Search Results

Search found 19055 results on 763 pages for 'high performance'.

Page 117/763 | < Previous Page | 113 114 115 116 117 118 119 120 121 122 123 124  | Next Page >

  • Stability, x86 Vs Sparc

    - by Jason T
    Our project are plan to migrate from Sparc to x86, and our HA requirement is 99.99%, previous on Sparc, we assume the hardware stability would like, hardware failure every 4 month or even one year, and also we have test data for our application, then we have requirement for each unplanned recovery (fail over) to achieve 99.99% (52.6 minutes unplanned downtime per year). But since we are going to use Intel x86, it seems the hardware stability is not so good as Sparc, but we don't have the detail data. So compare with Sparc, how about the stability of the Intel x86, should we assume we have more unplanned downtime? If so, how many, double? Where I can find some more detail of this two type of hardware?

    Read the article

  • distributed, fault-tolerant network block device

    - by gucki
    I'm looking for a distributed, fault-tolerant network storage system which exposes block devices (not filesystems) on the clients. A client's block device should write simultaneously to several storage nodes A client's block device should not fail as long as not all storage nodes backing it went down The master should automatically redistribute storages' data when a storage node fails or gets added/ removed A single master (which is for metadata only) is fine So ideally the architecture would be very similar to moosefs (http://www.moosefs.org/) but instead of exposing a real filesystem mounted using a fuse client it'd expose block devices on the clients. I know of iscsi and drbd but both don't seem to offer what I'm looking for. Or am I missing something?

    Read the article

  • Why does restarting the modem fix latency?

    - by Giovanni Galbo
    In the last few days I've noticed poor internet performance. Today I ran a speed test and the results were abysmal... 10mb down and 0.18mb up (which really hurt, because I was trying to RDC from another location). I pay for 30mb down and 5mb up. Latency was at 128ms. Before calling my ISP to give them a verbal lashing, I unplugged the modem and plugged it back in. I pretty much got top speed after doing that (with a latency of 7ms). I'm the type of guy that likes to know what goes on under the hood. So what's the deal? What mysterious powers does restarting give to my modem?

    Read the article

  • Apache on Win32: Slow Transfers of single, static files in HTTP, fast in HTTPS

    - by Michael Lackner
    I have a weird problem with Apache 2.2.15 on Windows 2000 Server SP4. Basically, I am trying to serve larger static files, images, videos etc. The download seems to be capped at around 550kB/s even over 100Mbit LAN. I tried other protocols (FTP/FTPS/FTP+ES/SCP/SMB), and they are all in the multi-megabyte range. The strangest thing is that, when using Apache with HTTPS instead of HTTP, it serves very fast, around 2.7MByte/s! I also tried the AnalogX SimpleWWW server just to test the plain HTTP speed of it, and it gave me a healthy 3.3Mbyte/s. I am at a total loss here. I searched the web, and tried to change the following Apache configuration directives in httpd.conf, one at a time, mostly to no avail at all: SendBufferSize 1048576 #(tried multiples of that too, up to 100Mbytes) EnableSendfile Off #(minor performance boost) EnableMMAP Off Win32DisableAcceptEx HostnameLookups Off #(default) I also tried to tune the following registry parameters, setting their values to 4194304 in decimal (they are REG_DWORD), and rebooting afterwards: HKLM\SYSTEM\CurrentControlSet\Services\AFD\Parameters\DefaultReceiveWindow HKLM\SYSTEM\CurrentControlSet\Services\AFD\Parameters\DefaultSendWindow Additionally, I tried to install mod_bw, which sets the event timer precision to 1ms, and allows for bandwidth throttling. According to some people it boosts static file serving performance when set to unlimited bandwidth for everybody. Unfortunately, it did nothing for me. So: AnalogX HTTP: 3300kB/s Gene6 FTPD, plain: 3500kB/s Gene6 FTPD, Implicit and Explicit SSL, AES256 Cipher: 1800-2000kB/s freeSSHD: 1100kB/s SMB shared folder: about 3000kB/s Apache HTTP, plain: 550kB/s Apache HTTPS: 2700kB/s Clients that were used in the bandwidth testing: Internet Explorer 8 (HTTP, HTTPS) Firefox 8 (HTTP, HTTPS) Chrome 13 (HTTP, HTTPS) Opera 11.60 (HTTP, HTTPS) wget under CygWin (HTTP, HTTPS) FileZilla (FTP, FTPS, FTP+ES, SFTP) Windows Explorer (SMB) Generally, transfer speeds are not too high, but that's because the server machine is an old quad Pentium Pro 200MHz machine with 2GB RAM. However, I would like Apache to serve at at least 2Mbyte/s instead of 550kB/s, and that already works with HTTPS easily, so I fail to see why plain HTTP is so crippled. I am using a Kerio Winroute Firewall, but no Throttling and no special filters peeking into HTTP traffic, just the plain Firewall functionality for blocking/allowing connections. The Apache error.log (Loglevel info) shows no warnings, no errors. Also nothing strange to be seen in access.log. I have already stripped down my httpd.conf to the bare minimum just to make sure nothing is interfering, but that didn't help either. If you have any idea, help would be greatly appreciated, since I am totally out of ideas! Thanks! Edit: I have now tried a newer Apache 2.2.21 to see if it makes any difference. However, the behaviour is exactly the same. Edit 2: KM01 has requested a sniff on the HTTP headers, so here comes the LiveHTTPHeaders output (an extension to Firefox). The Output is generated on downloading a single file called "elephantsdream_source.264", which is an H.264/AVC elementary video stream under an Open Source license. I have taken the freedom to edit the URL, removing folders and changing the actual servers domain name to www.mydomain.com. Here it is: LiveHTTPHeaders, Plain HTTP: http://www.mydomain.com/elephantsdream_source.264 GET /elephantsdream_source.264 HTTP/1.1 Host: www.mydomain.com User-Agent: Mozilla/5.0 (Windows NT 5.2; WOW64; rv:6.0.2) Gecko/20100101 Firefox/6.0.2 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: de-de,de;q=0.8,en-us;q=0.5,en;q=0.3 Accept-Encoding: gzip, deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Connection: keep-alive HTTP/1.1 200 OK Date: Wed, 21 Dec 2011 20:55:16 GMT Server: Apache/2.2.21 (Win32) mod_ssl/2.2.21 OpenSSL/0.9.8r PHP/5.2.17 Last-Modified: Thu, 28 Oct 2010 20:20:09 GMT Etag: "c000000013fa5-29cf10e9-493b311889d3c" Accept-Ranges: bytes Content-Length: 701436137 Keep-Alive: timeout=15, max=100 Connection: Keep-Alive Content-Type: text/plain LiveHTTPHeaders, HTTPS: https://www.mydomain.com/elephantsdream_source.264 GET /elephantsdream_source.264 HTTP/1.1 Host: www.mydomain.com User-Agent: Mozilla/5.0 (Windows NT 5.2; WOW64; rv:6.0.2) Gecko/20100101 Firefox/6.0.2 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: de-de,de;q=0.8,en-us;q=0.5,en;q=0.3 Accept-Encoding: gzip, deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Connection: keep-alive HTTP/1.1 200 OK Date: Wed, 21 Dec 2011 20:56:57 GMT Server: Apache/2.2.21 (Win32) mod_ssl/2.2.21 OpenSSL/0.9.8r PHP/5.2.17 Last-Modified: Thu, 28 Oct 2010 20:20:09 GMT Etag: "c000000013fa5-29cf10e9-493b311889d3c" Accept-Ranges: bytes Content-Length: 701436137 Keep-Alive: timeout=15, max=100 Connection: Keep-Alive Content-Type: text/plain

    Read the article

  • Do SSD hybrid drives perform better than HDD + ReadyBoost flash?

    - by Chris W. Rea
    Seagate has released a product called the Momentus XT Solid State Hybrid Drive. This looks exactly like what Windows ReadyBoost attempts to do with software at the OS level: Pairing the benefits of a large hard drive together with the performance of solid-state flash memory. Does the Momentus XT out-perform a similar ad-hoc pairing of a decent hard drive with similar flash memory storage under Windows ReadyBoost? Other than the obvious "a hardware implementation ought to be faster than a software implementation", why would ReadyBoost not be able to perform as well as such a hybrid device?

    Read the article

  • Interpreting Munin graphs showing available entropy and MySQL slow queries in sync

    - by user64204
    We're experiencing performance issues on our website, and after reviewing our munin graphs, the only metrics we've found in sync are Available entropy and MySQL slow queries, with the latter influenced by our number of logged in users: Based on the wikipedia entropy page, my understanding is that entropy is the amount of randomness (here measured in bytes) that the system can use for various tasks, mainly cryptography and functions that require random input. Since the peaks in available entropy and MySQL slow queries are occurring in sync and at regular interval, that the number of MySQL slow queries is proportional to our number of Drupal users whereas the peaks in available entropy seem to be much more constant and less proportional to these 2 metrics, we're thinking available entropy is the reflect of a root cause which, combined with the traffic to our website, is causing those slow queries (and not the opposite, slow queries influencing the entropy). Accordingly: Q: What underlying problem do you think could cause regular peaks in available entropy that could have an influence on MySQL's ability to process queries?

    Read the article

  • What are the quality metrics for RAM?

    - by Hi-Tech KitKat Android
    I have searched RAM and i found there are given some specification for the same capacity RAM, What are the difference and performance comparison between these? Like RAM1 General Brand Transcend Memory Type 2 GB (8 x 128 MB) DDR2 DIMM Memory Standard DDR2-800/PC-6400 Compatible Device PC Pins 240-pin Burst Length 4, 8 Buffered/Unbuffered Unbuffered Memory Memory Clock 400 MHz Technology DDR2 SDRAM Memory CAS Latency 4, 5, 6 RAM 2 General Brand Transcend Memory Type 2 GB (8 x 128 MB) DDR2 DIMM Memory Standard DDR2-667/PC2-5300 Compatible Device PC Pins 240-pin Burst Length 4, 8 Buffered/Unbuffered Unbuffered Memory Memory Clock 333 MHz Technology DDR2 SDRAM Memory CAS Latency 3, 4, 5 RAM3 General Brand Kingston Memory Type 2 GB (64 x 256 MB) 800 MHz DDR2 DIMM Compatible Device PC Pins 240-pin Error Check Non-ECC Buffered/Unbuffered Unbuffered Memory Memory Clock 200 MHz Technology DDR2 SDRAM Memory CAS Latency 6 What are the affect of the following Memory Type(given as 8 x 128 MB) Memory Clock (given in MHz) CAS Latency (given as 4,5,6) my Requirement is 2 GB DDR2 Type Desktop Please help

    Read the article

  • Intel cpu hyperthreading on or off for ibm db2?

    - by rtorti19
    Has anyone ever done any database performance comparisons with hyper-threading enabled vs disabled? We are running ibm db2 and I'm curious if anyone has an recommendations for enabling hyper-threading or not. With hyper-threading enabled it makes it quite difficult to do capacity planning for cpu usage. For example. "With 8 physical cores represented as 16 "threads" on the OS and a cpu-bound workload, does that mean when your cpu usage hit's 50% you are actually running at 100%." What real benefits do I gain with leaving hyper-threading enabled on an intel server running DB2? Does hyper-threading help if you're workload is truly disk IO bound? If so, up to what percentage? These are the types of questions I'm trying to answer. Any thoughts?

    Read the article

  • Benchmarks relevant for a Visual Studio .Net development workstation

    - by user30715
    I am developing a system with Windows 7-64, Visual Studio and Sharepoint on a virtual workstation on some kind of VMWare server. The system is painfully slow, with VS lagging behind when entering code, Intellisense lagging, opening and saving files takes ages when compared to a normal budget laptop. As far as I can see the virtual machine has OK specs and does not seem to be swapping etc., and the IT dept also says that they can't see anything wrong when they're monitoring the system. As long as the problem is not well-documented, the IT dept and management does not want to throw money (=upgraded laptops) at us, so I need to show some sort of benchmark. It has been many years since I did any system benchmarking, and I don't know the current benchmark software, so my question is which benchmark will be most relevant for Visual Studio performance? Not just for compiling fast, but also to reflect the "responsiveness" of the system. Cheers, user30715

    Read the article

  • Free DNS software with failover support?

    - by Lin
    I'm looking for DNS software that can accomplish the following: Check health of all A records at set intervals If server is unresponsive after multiple successive checks, replace A record with a working server When a server is down, check it periodically. Once it's up, restore normal A records Here's an equivalent I thought of: Run DNS servers with very low TTL (minutes) Use a cron job to periodically query all webservers Use sed to replace A records if need be, and then restart DNS server I have a hard time believing there isn't already something that can accomplish the above. I'm not looking for a paid service, and I'm restricted to anything I can run with root access to a VPS. Any suggestions would be great. Thanks!

    Read the article

  • How do I load balance between two Linux machines?

    - by William Hilsum
    Inspired by the Stack Overflow network, I am now obsessed with HAProxy and trying to use it myself. At the moment, each HAProxy box has got two network cards (well, two configured, I can have a maximum of 4 and wasn't sure if they needed their own one for management between the boxes). On both machines, the backend one (eth1) is a private IP that goes to a switch connected to the webservers, and the front facing one (eth0) has a public internet IP that is routed straight though. In addition, I have created an additional virtual ip for eth0 called eth0:0 which has got a third public ip address. I just about get how to use it for load balancing between multiple web servers that are behind it, but, I am failing to load balance between the two HAProxy boxes - they appear to fight for the virtual IP, but, this does not appear to be a smart solution. Now, by using the virtual shared IP address, this solution appears to work and does seem to give me maximum uptime, but, is this the correct way to do it, or is there a smarter way? I have been looking at other Linux packages such as keepalived, but, I have only been using Linux (server) for a week now and am at the limits of my understanding. Is there anyone who has done this before and can you advise anything for maximum uptime?

    Read the article

  • Rail's FileStore with Linux Disk Caching or RAMdisk?

    - by Yo Ludke
    I have a Ruby on Rails application that stores it's catched files on the filesystem (Rails file-system cache). I was thinking about changing to memcached Store, but a short test shows it isn't a big difference in speed. From linuxatemyram.com I learned a bit about file caching. On the current machine there would be around 40..45GB RAM left which isn't needed for the application and which can be used to linux-disk-cache this rails file cache store. The disk is a RAID10 system with almost 120MB disk perfomance. How can I tell Linux to use free RAM more deliberately and not to be shy about using it? Do think it's necessary to adjust a sysyctl/.. value here, or would I have performance advantages to put the File Store root diretory on a ramdisk? (Loosing the cache during a reboot wouldn't be a problem)

    Read the article

  • Do you run anti-virus software?

    - by Paolo Bergantino
    Do you find the crippling effect that most anti virus software has on a computer's performance worth the "security" they provide? I've never been able to really tell myself its worth it, and have used my computer without "protection" for years without any problems. Jeff Atwood wrote about this a while back, taking a similar stance. So I'm looking for some discussion on the merits and downfalls of antivirus software, and whether you personally think its worth the hassle. One point I do think is valid is that I am probably okay with not running it because I know if something goes wrong I have the ability to make it right (most of the time) but I can't really recommend the same for family as they may not be able to...

    Read the article

  • DRBD Replication failure

    - by user62513
    A couple of weeks ago I setup a 2 nodes CRM system with one of the resources managed being MySQL over DRBD. Today for maintenance reasons I restarted both nodes but now they can't connect to each other anymore. DRBD fell out of sync and I followed this guide to get it back connected but it's only able to run successfully on one node. But this strange thing happens: If I crm node standby both nodes and I try: crm node online node0 before crm node online node1, all the CRM resources start successfully but the DRBD partitions are still running in StandAlone state. crm node online node1 beofre crm node online node0, the DRBD resource fails to start, thus causing mysql not to start. If I standby both resources and call crm node online node0 then it times out and prints this error: Running crm node online node0 produces this output after timing out Error setting standby=off (section=nodes, set=<null>): Remote node did not respond Error performing operation: Remote node did not respond Is there anything I'm doing wrong here? An alternative will be just do MySQL replication but I'm not sure how to promote a slave to master when the master database is not available.

    Read the article

  • reducing Windows 7 size

    - by Sejanus
    My Windows 7 uses around 16 GB while Windows XP only around 4 GB hard disk space. Seems weird. I use Windows only for gaming so I dont need a lot of stuff they have to offer. What is the best way to reduce Windows 7 size? What can I delete / uninstall and how? Also I'd like reduce RAM and processor usage as much as possible (as long as it doesnt hurt game performance)... turn off all that fancy stuff and so on. What can I turn off and how? Thanks in advance!

    Read the article

  • How to make AD highly available for applications that use it as an LDAP service

    - by Beaming Mel-Bin
    Our situation We currently have many web applications that use LDAP for authentication. For this, we point the web application to one of our AD domain controllers using the LDAPS port (636). When we have to update the Domain Controller, this has caused us issues because one more web application could depend on any DC. What we want We would like to point our web applications to a cluster "virtual" IP. This cluster will consist of at least two servers (so that each cluster server could be rotated out and updated). The cluster servers would then proxy LDAPS connections to the DCs and be able to figure out which one is available. Questions For anyone that has had experience with this: What software did you use for the cluster? Any caveats? Or perhaps a completely different architecture to accomplish something similar?

    Read the article

  • Tuning (and understanding) table_cache in mySQL

    - by jotango
    Hello, I ran the excellent MySQL performance tuning script and started to work through the suggestions. One I ran into was TABLE CACHE Current table_cache value = 4096 tables You have a total of 1073 tables. You have 3900 open tables. Current table_cache hit rate is 2%, while 95% of your table cache is in use. You should probably increase your table_cache I started to read up on the table_cache but found the MySQL documentation quite lacking. They do say to increase the table_cache, "if you have the memory". Unfortunately the table_cache variable is defined as "The number of open tables for all threads." How will the memory used by MySQL change, if I increase this variable? What is a good value, to set it to?

    Read the article

  • Server and Application architecture for large outgoing email volume.

    - by Ezequiel
    Hi, we need to develop an application to send large amount of emails (newsletters) We estimate 15 millions of emails per month (6 - 10 emails per seconds). Would you recommend me the proper architecture for this application? should we have several MTA agents and use them in a round robin fashion? What considerations should we take on account to not being treated as spammers (its really not spam what we are going to send). Thanks for your help. Ezequiel

    Read the article

  • master-slave datastore replication, automatic failover, and wackamole

    - by z8000
    I have 2 dedicated servers provisioned for my next project's datastores. The datastores are configured for master-slave replication. There's no inherent automatic failover but I of course want this. That is, I'd love for access to the master datastore to always just work without having to configure a client library to detect when a master is down and failover to the slave. I've seen Wackamole which is based on the Spread Toolkit. You provide Wackamole with a set of IPs and a bunch of nodes, and regardless of the up/down state of any of the nodes, those IPs will stay available/up. Wackamole detects when a node goes down and ARPs the IP(s) that were up on the now-down node. It's pretty neat actually. So, my thought was to use Wackamole to keep the 2 virtual private IPs available/up. Clients would then just always use the same private IP to access the master datastore and the same but distinct IP for the slave datastore, even if those IPs were hosted on the same node. My datastore servers are accessed over a private network. I am unsure if this messes with Wackamole though. Is this lunacy? How do you generally handle automatic failover of private services like a datastore. FWIW, it shouldn't matter but the datastore is Redis. I don't want to hear "use mySQL" please :) Thanks.

    Read the article

  • How complex of a daemon should be run through inetd?

    - by amphetamachine
    What is the general rule for which daemons should be started up through inetd? Currently, on my server, sshd, apache and sendmail are set up to run all the time, where simple *NIX services are set up to be started by inetd. I'm the only one who uses ssh on my computer, and break-in attempts aren't a problem because I have it running on a non-standard port, and my HTTP server gets maybe 5 hits a day that aren't GoogleBot. My question is, what are the benefits vs. the performance hits associated with running a complex daemon like sshd or apache through superserver, and what, if any successes or failures have you had running your own daemons in this manner?

    Read the article

  • Corosync :: Restarting some resources after Lan connectivity issue

    - by moebius_eye
    I am currently looking into corosync to build a two-node cluster. So, I've got it working fine, and it does what I want to do, which is: Lost connectivity between the two nodes gives the first node '10node' both Failover Wan IPs. (aka resources WanCluster100 and WanCluster101 ) '11node' does nothing. He "thinks" he still has his Failover Wan IP. (aka WanCluster101) But it doesn't do this: '11node' should restart the WanCluster101 resource when the connectivity with the other node is back. This is to prevent a condition where node10 simply dies (and thus does not get 11node's Failover Wan IP), resulting in a situation where none of the nodes have 10node's failover IP because 10node is down 11node has "given back" his failover Wan IP. Here's the current configuration I'm working on. node 10sch \ attributes standby="off" node 11sch \ attributes standby="off" primitive LanCluster100 ocf:heartbeat:IPaddr2 \ params ip="172.25.0.100" cidr_netmask="32" nic="eth3" \ op monitor interval="10s" \ meta is-managed="true" target-role="Started" primitive LanCluster101 ocf:heartbeat:IPaddr2 \ params ip="172.25.0.101" cidr_netmask="32" nic="eth3" \ op monitor interval="10s" \ meta is-managed="true" target-role="Started" primitive Ping100 ocf:pacemaker:ping \ params host_list="192.0.2.1" multiplier="500" dampen="15s" \ op monitor interval="5s" \ meta target-role="Started" primitive Ping101 ocf:pacemaker:ping \ params host_list="192.0.2.1" multiplier="500" dampen="15s" \ op monitor interval="5s" \ meta target-role="Started" primitive WanCluster100 ocf:heartbeat:IPaddr2 \ params ip="192.0.2.100" cidr_netmask="32" nic="eth2" \ op monitor interval="10s" \ meta target-role="Started" primitive WanCluster101 ocf:heartbeat:IPaddr2 \ params ip="192.0.2.101" cidr_netmask="32" nic="eth2" \ op monitor interval="10s" \ meta target-role="Started" primitive Website0 ocf:heartbeat:apache \ params configfile="/etc/apache2/apache2.conf" options="-DSSL" \ operations $id="Website-one" \ op start interval="0" timeout="40" \ op stop interval="0" timeout="60" \ op monitor interval="10" timeout="120" start-delay="0" statusurl="http://127.0.0.1/server-status/" \ meta target-role="Started" primitive Website1 ocf:heartbeat:apache \ params configfile="/etc/apache2/apache2.conf.1" options="-DSSL" \ operations $id="Website-two" \ op start interval="0" timeout="40" \ op stop interval="0" timeout="60" \ op monitor interval="10" timeout="120" start-delay="0" statusurl="http://127.0.0.1/server-status/" \ meta target-role="Started" group All100 WanCluster100 LanCluster100 group All101 WanCluster101 LanCluster101 location AlwaysPing100WithNode10 Ping100 \ rule $id="AlWaysPing100WithNode10-rule" inf: #uname eq 10sch location AlwaysPing101WithNode11 Ping101 \ rule $id="AlWaysPing101WithNode11-rule" inf: #uname eq 11sch location NeverLan100WithNode11 LanCluster100 \ rule $id="RAND1083308" -inf: #uname eq 11sch location NeverPing100WithNode11 Ping100 \ rule $id="NeverPing100WithNode11-rule" -inf: #uname eq 11sch location NeverPing101WithNode10 Ping101 \ rule $id="NeverPing101WithNode10-rule" -inf: #uname eq 10sch location Website0NeedsConnectivity Website0 \ rule $id="Website0NeedsConnectivity-rule" -inf: not_defined pingd or pingd lte 0 location Website1NeedsConnectivity Website1 \ rule $id="Website1NeedsConnectivity-rule" -inf: not_defined pingd or pingd lte 0 colocation Never -inf: LanCluster101 LanCluster100 colocation Never2 -inf: WanCluster100 LanCluster101 colocation NeverBothWebsitesTogether -inf: Website0 Website1 property $id="cib-bootstrap-options" \ dc-version="1.1.7-ee0730e13d124c3d58f00016c3376a1de5323cff" \ cluster-infrastructure="openais" \ expected-quorum-votes="2" \ no-quorum-policy="ignore" \ stonith-enabled="false" \ last-lrm-refresh="1408954702" \ maintenance-mode="false" rsc_defaults $id="rsc-options" \ resource-stickiness="100" \ migration-threshold="3" I also have a less important question concerning this line: colocation NeverBothLans -inf: LanCluster101 LanCluster100 How do I tell it that this collocation only applies to '11node'.

    Read the article

  • Most scalable way of serving a small set of static HTTP content

    - by Ekevoo
    The story: Hi guys. I'm among the people responsible for serving the results of the most anticipated (by number of people participating) annual entrance exam in my state. As such, when our results are published, the interest is overwhelming. In the past we delegated the responsibility of serving the results to the media, but that spoils a little the officialness of these results. This year we went with a little (long overdue) experiment of using lighttpd instead of Apache as well as other physical network optimizations I wasn't directly involved with. The results were very satisfactory. The server didn't choke even once, nor we saw any of the usual Twitter complaints on unavailability and/or slowness that were previously common. However, because we still delegated the first publication of the results to the media I'm still not 100% sure we can handle the load of actually publishing the results first. The question: Now because these files are like 14MB in total and a true lightweight Linux distribution isn't that big either, I'm thinking: what if next year we run full RAMdrive? Is there any? Is that useful? Is that worth it for a team that uses Debian almost exclusively? Are there other optimizations that I should be focusing on instead?

    Read the article

  • Does anyone still use Iometer?

    - by Brian T Hannan
    "Iometer is an I/O subsystem measurement and characterization tool for single and clustered systems. It is used as a benchmark and troubleshooting tool and is easily configured to replicate the behaviour of many popular applications." link text Does anyone still use this tool? It seems helpful, but I'm not sure if it's for the thing I am trying to work on. I am trying create a benchmark computer performance test that can be run before and after a Windows Optimization program does its stuff (ex: PC Optimizer Pro or CCleaner). I want to be able to make a quick statement like CCleaner makes the computer run 50% faster or something along those lines. Are there any newer tools like this one?

    Read the article

  • Tools to manage sql 2008 database mirroring?

    - by lemkepf
    We are going to be moving about 20 databases that live on a single instance of sql 2000 to a sql 2008 r2 environment with database mirroring. What I'm looking for is a tool or scripts that will help me manage the conversion and management of those 20db's onto this new mirrored environment easily. There are many steps in setting each DB up and I want to automate as much as possible. Edit: Here are the steps I've been doing manually: Create the same username/passwords from the old sql 2000 server onto new sql 2008 server. Then sync those users/passwords onto the other sql 2008 server with the same SSID's so when we do the db backup and restore they match up. Take a backup of each sql 2000 db's. Copy them to server A. Restore the backup to server A. Backup from server a, copy to server b, restore there. Run the mirror "configure security" wizard. Start mirroring. I've love to be able to script this out or have a tool that does it for me. Thanks! Paul

    Read the article

  • SBD killing both cluster nodes when there are even small SAN network problems

    - by Wieslaw Herr
    I am having problems with stonith SBD in a openais-based cluster. Some background: The active/passive cluster has two nodes, node1 and node2. They are configured to provide an NFS service to users. To avoid problems with split-brain, they are both configured to use SBD. SBD is using two 1MB disks available to the hosts via an multipath fibre-channel network. The problems start if something happens with the SAN network. For example, today one of the brocade switches got rebooted and both nodes lost 2 out of 4 paths to each disks, which resulted in both nodes committing suicide and rebooting. This, of course, was highly undesirable because a) there were paths left b) even if the switch would be out for 10-20 seconds a reboot cycle of both nodes would take 5-10 minutes and all NFS-locks would be lost. I tried increasing the SBD timeout values (to 10sec+ values, dump attached at the end), however a "WARN: Latency: No liveness for 4 s exceeds threshold of 3 s" hints that something isn't working as I would it expect to. Here is what I would like to know: a) Is SBD working as it should killing nodes when 2 paths are available? b) If not, is the multipath.conf file attached correct? The storage controller we use is an IBM SVC (IBM 2145), should there be any specific configuration for it? (as in multipath.conf.defaults) c) How should I go about increasing the timeouts in SBD attachements: Multipath.conf and sbd dump (http://hpaste.org/69537)

    Read the article

< Previous Page | 113 114 115 116 117 118 119 120 121 122 123 124  | Next Page >