Search Results

Search found 47090 results on 1884 pages for 'linux ubuntu customize'.

Page 168/1884 | < Previous Page | 164 165 166 167 168 169 170 171 172 173 174 175  | Next Page >

• Is it possible to mount a hot-swappable drive when it is turned on?

  - by John

  In my PC, I have a hot-swap drive. Usually I keep it off to save power. I only really use it when accessing from another PC on the network. Is it possible to configure /etc/fstab to mount this drive when I turn it on (without having to shake the mouse, open file manager and click the drive to have it mounted? Currently, I have: UUID=a869e5ca-7d3b-4d64-91e2-eadbecd8c9e5 /media/i-TVShows ext4 rw,nosuid,nodev,auto,user,uhelper=udisks 0 0 in my /etc/fstab file but it doesn't seem to do the trick. I want the drive to be user-mountable, on power on, with RW access, and I'm thinking of adding 'nofail'...this is my first time writing to the fstab file, and a lot of the parameters I took from the output of 'mount' so feel free to correct any oddness you find. Thanks

  Read the article

• Linux (DUP!) ping packages

  - by Darkmage

  i cant seem t figure out what is going on here. The Linux machine I am using is running as a VM on a Win7 machine using Virtual Box running as a service. If i ping the win7 Host i get ok result. root@Virtual-Box:/home/glennwiz# ping -c 100000 -s 10 -i 0.02 192.168.1.100 PING 192.168.1.100 (192.168.1.100) 10(38) bytes of data. 18 bytes from 192.168.1.100: icmp_seq=1 ttl=128 time=1.78 ms 18 bytes from 192.168.1.100: icmp_seq=2 ttl=128 time=1.68 ms if i ping localhost im ok root@Virtual-Box:/home/glennwiz# ping -c 100000 -s 10 -i 0.02 localhost PING localhost (127.0.0.1) 10(38) bytes of data. 18 bytes from localhost (127.0.0.1): icmp_seq=1 ttl=64 time=0.255 ms 18 bytes from localhost (127.0.0.1): icmp_seq=2 ttl=64 time=0.221 ms but if i ping gateway i get DUP packets root@Virtual-Box:/home/glennwiz# ping -c 100000 -s 10 -i 0.02 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 10(38) bytes of data. 18 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=1.27 ms 18 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=1.46 ms (DUP!) 18 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=22.1 ms 18 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=22.4 ms (DUP!) if i ping other machine on same LAN i stil get dups. pinging remote hosts also gives (DUP!) result root@Virtual-Box:/home/glennwiz# ping -c 100000 -s 10 -i 0.02 www.vg.no PING www.vg.no (195.88.55.16) 10(38) bytes of data. 18 bytes from www.vg.no (195.88.55.16): icmp_seq=1 ttl=245 time=10.0 ms 18 bytes from www.vg.no (195.88.55.16): icmp_seq=1 ttl=245 time=10.3 ms (DUP!) 18 bytes from www.vg.no (195.88.55.16): icmp_seq=2 ttl=245 time=10.3 ms 18 bytes from www.vg.no (195.88.55.16): icmp_seq=2 ttl=245 time=10.6 ms (DUP!)

  Read the article

• Dropped connections between Linux Servers in Data Center

  - by Emil H

  I have a number of linux servers at a us-based datacenter. The servers were installed by the hosting company, and are running fedora core. We're experiencing problems with dropped connections. The issue seems to be that when we attempt to connect to one of the other servers after a period of inactivity, the first connection attempt will fail, and sometimes the second. However, after that the connection succeds and it works for a while. This happens for both mysql connections and raw socket connections, but only seems to occur when connecting to some of our servers. The confusing part is that it some of the servers for which we see different behaviors have identical hardware configuration and software. For example, it happens when connecting to a server called mysql2, but not for a server called mysql3. These servers were installed at the same time, but the same specifications. The problem can be reproduced somewhat reliably, but only after waiting fifteen minutes to half an hour. This makes it hard to diagnose, and even harder since I'm not really sure what to look for. I realize that connections sometimes failed, and that we should write our applications to compensate for this but these servers all in the same data center. Why would it matter if two servers haven't communicated for a while? Does anybody have an idea what might be causing this? Is it a server configuration problem or a network problem that I should contact the hosting company about. What do I tell them to look for? Unfortunately our experience has been that the support staff doesn't investigate problems in depth unless we give them detailed directions.

  Read the article

• NFSv3 + ACL: mask is gone on clients

  - by Jorge Suárez de Lis

  I'm sharing a NFS folder among a user group. The default umask on the clients is 0700, and this is a problem because newly created files won't be readable/writable by another users. So, I'm using ACLs to force the umask 0770 on the shared folder, and this works OK on the server, but not on the clients. server # getfacl /export/proyectos getfacl: Eliminando «/» inicial en nombres de ruta absolutos # file: export/proyectos # owner: root # group: root user::rwx group::rwx other::r-x default:user::rwx default:group::rwx default:mask::rwx default:other::r-x server # getfacl /export/proyectos/innovacion getfacl: Eliminando «/» inicial en nombres de ruta absolutos # file: export/proyectos/innovacion # owner: root # group: proyecto-innovacion # flags: ss- user::rwx group::rwx mask::rwx other::--- default:user::rwx default:group::rwx default:mask::rwx default:other::--- As you see, the default (and also a specific on the second directory) mask ACLs are being applied. I mount the whole share on the client: 172.16.54.56:/export/proyectos on /proyectos type nfs (rw,noatime,rsize=131072,wsize=131072,acregmin=10,acl,nfsvers=3,addr=172.16.54.56) But the mask and default:mask ACLs are gone. client $ getfacl /proyectos/ getfacl: Eliminando «/» inicial en nombres de ruta absolutos # file: proyectos/ # owner: root # group: root user::rwx group::rwx other::r-x default:user::rwx default:group::rwx default:other::r-x client $ getfacl /proyectos/innovacion getfacl: Eliminando «/» inicial en nombres de ruta absolutos # file: proyectos/innovacion # owner: root # group: proyecto-innovacion # flags: ss- user::rwx group::rwx other::--- default:user::rwx default:group::rwx default:other::--- It lacks the default:mask and mask ACLs, the only ones that I've setted. So the proposed solution to enforce umask won't work for me. Why is happening this?

  Read the article

• cannot install Komodo IDE

  - by Delirium tremens

  I double-click komodo, but it doesn't run. In the Terminal, I type "echo $PATH", but the Komodo dir isn't there. There too, I type "komodo", but the command isn't found. While trying to install Komodo, I may have typed wrong paths. How to correct $PATH? How to run Komodo? echo $PATH echoes /usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games

  Read the article

• LS command for torrent files

  - by amir-beygi

  Hi all I have a directory full of torrent files,and i have to download all of them; But the problem is i have disk limit in my remote server,and file sizes are vary(100MB~8GB) and if i add all of torrent files ,none of them would be download completely;So i need a command to list all my torrents and the size of them , to be selected and add to download list later . NOTE: REMOTE SERVER - LINUX_UBUNTU_9.10 // SSH So i need a command like torrentls That output somethings like: file1.torrent 1111MB file2.torrent 222MB file3.torrent 3333MB file4.torrent 444MB file5.torrent 5555MB

  Read the article

• Failing to send email on Ubuntu box (Karmic Koala)

  - by user25312

  I have a home network with an XP and Ubuntu (9.10) box. I have created a small test php script for checking that I can send emails from my machine. I am using the same php.ini file with the same [mail settings], yet the file works on my XP box, and fails on the Ubuntu box. I have included the script here, hopefully, someone can spot whats going wrong: <?php // send e-mail to ... $to="[email protected]"; // Your subject $subject="Test Email"; // From //$header="from: test script"; $header='From: host-email-username@hostdomain_here' . "\r\n" . // Your message $message="Hello \r\n"; $message.="This is test\r\n"; $message.="Test again "; // send email $sentmail = mail($to,$subject,$message,$header); // if your email succesfully sent if($sentmail){ echo "Email Has Been Sent ."; } else { echo "Cannot Send Email "; } ?> The emails have been spoofed for obvious reasons, but otherwise, the script is exactly as the one I tested [Edit] I have since installed mailutils package on my Ubuntu box, now the script runs and returns 'Email has been sent'. However, the mail never arrives in my mail inbox (I've waited 1 day so far). Is there something else I need to be looking at?

  Read the article

• Configuring sudo to work without password

  - by aidan

  I'm trying to configure sudo to allow all users to restart apache without having to enter a password. Security concerns aside, why isn't this working? I added the line to /etc/sudoers: %admin ALL=NOPASSWD: /usr/sbin/apache2ctl $sudo -l User aidan may run the following commands on this host: (root) NOPASSWD: /usr/sbin/apache2ctl (ALL) ALL $sudo /usr/sbin/apache2ctl [sudo] password for aidan: Thanks for any help.

  Read the article

• LSI MegaRAID LINUX got Optimal after degradation but strange POST message

  - by kesrut

  Linux server box with LSI MegaRAID controller got degraded. But after some time RAID status changed to Optimal. Adapter 0 -- Virtual Drive Information: Virtual Drive: 0 (Target Id: 0) Name : RAID Level : Primary-1, Secondary-0, RAID Level Qualifier-0 Size : 2.727 TB Mirror Data : 2.727 TB State : Optimal Strip Size : 256 KB Number Of Drives per span:2 Span Depth : 3 Default Cache Policy: WriteBack, ReadAdaptive, Cached, No Write Cache if Bad BBU Current Cache Policy: WriteThrough, ReadAdaptive, Cached, No Write Cache if Bad BBU Default Access Policy: Read/Write Current Access Policy: Read/Write Disk Cache Policy : Disk's Default Encryption Type : None Is VD Cached: No But now I'm getting RAID BIOS POST message: Your battery is either charging, bad or missing, and you have VDs configured for write-back mode. Because the battery is not currently usable, these VDs willl actually run in write-through mode until the battery is fully charged or replaced if it is bad or missing. (Image: http://cl.ly/image/1h1O093b1i2d) So may it be battery issue caused problem ? I get information about battery: BatteryType: iBBU Voltage: 4001 mV Current: 0 mA Temperature: 22 C Battery State : Operational BBU Firmware Status: Charging Status : None Voltage : OK Temperature : OK Learn Cycle Requested : No Learn Cycle Active : No Learn Cycle Status : OK Learn Cycle Timeout : No I2c Errors Detected : No Battery Pack Missing : No Battery Replacement required : No Remaining Capacity Low : No Periodic Learn Required : No Transparent Learn : No No space to cache offload : No Pack is about to fail & should be replaced : No Cache Offload premium feature required : No Module microcode update required : No Where can be problem ? I'm disabled alarms, but get them if enabled. But don't know how find root of problem.

  Read the article

• Open a file with eclipse via terminal and focus eclipse window

  - by Rui Carneiro

  I am a webdeveloper and my current working tools are: Terminal (ssh, tailing logs, grep, git, etc) Eclipse (PDT, Javascript, etc) Firefox (Developer Toolbar + Firebug) The problem is that I hate using the eclipse navigation tree. For me it is a lot easier to go to the Terminal and do something like this: $ eclipse /var/www/myproject/long/path/lib/Driver/Sql.php The annoying part is that the eclipse window is not focused after this command. I have to manually click on the eclipse window (using mouse... :@ grrr) Anyway to force eclipse to be focused?

  Read the article

• Bad results converting PDF to EPS on Linux

  - by Tim

  I'm having some trouble converting PDFs (created by Adobe Illustrator on a Mac) to EPS. I have tried several things but I am wondering if there is a better option. The following list is ordered by decreasing quality: inkscape --export-area-page --export-eps=out.eps in.pdf using the graphical program Inkscape works best, but is a bit slow; pdftops -eps in.pdf out.eps uses Poppler and works good and is fast; pdf2ps in.pdf out.eps uses ghostscript and works ok for simple documents; convert in.pdf out.eps uses ImageMagick and always rasterizes the image. I haven't tested the following: acroread -toPostScript use acroread (Linux only) Some issues I've found: Transparency is not supported in EPS, but instead of flattening the layers, most programs rasterize the image producing big files and ugly graphs. Inkscape does this best by only rasterizing the unsupported area. Gradients are rendered properly by Inkscape, but Poppler somehow chops up the gradient into many shapes of different colors. Greek symbols are seemingly not supported by Ghostscript and are rasterized (using pdf2ps). What are your experiences for this kind of task? Did I forgot certain programs and/or command line options that improve quality? I found some posts on this, but not a (thorough) comparison of possibilities, please correct me if I'm wrong. Related posts How to convert PDF to EPS? on TeX

  Read the article

• Routing data through VPN in linux

  - by Shadyabhi

  I think its a silly question but still here it goes.. Terminal Output: eth0 Link encap:Ethernet HWaddr 00:1c:c0:37:5e:25 inet addr:10.100.98.51 Bcast:10.100.98.255 Mask:255.255.255.0 inet6 addr: fe80::21c:c0ff:fe37:5e25/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:29677 errors:0 dropped:0 overruns:0 frame:0 TX packets:5209 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:3179007 (3.1 MB) TX bytes:610142 (610.1 KB) Memory:e0380000-e03a0000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:76 errors:0 dropped:0 overruns:0 frame:0 TX packets:76 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:9555 (9.5 KB) TX bytes:9555 (9.5 KB) vpn_0 Link encap:Ethernet HWaddr 00:ac:39:95:a1:16 inet6 addr: fe80::2ac:39ff:fe95:a116/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1786 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:128597 (128.5 KB) TX bytes:468 (468.0 B) Actually, I followed this tutorial to setup the PacketiX VPN on ubuntu. Now, how do I actually use this VPN? Terminal Output: shadyabhi@shadyabhi-desktop:~$ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 default 10.100.98.4 0.0.0.0 UG 0 0 0 eth0 shadyabhi@shadyabhi-desktop:~$ As told in tutorial, if I do route del default route add default dev vpn_0 I am not able to surf the internet. And I get the route command output as: root@shadyabhi-desktop:/home/shadyabhi# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.100.98.0 * 255.255.255.0 U 1 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 eth0 default * 0.0.0.0 U 0 0 0 vpn_0 root@shadyabhi-desktop:/home/shadyabhi# I know I am not able to route the traffic properly. How do i do that?

  Read the article

• Running git-svn with cron results in garbage in .git

  - by Paul

  I've setup a git-svn repo with cron to fetch from the svn repo daily. I have a script to do the fetching, and this is what is invoked by cron. Everything is fine with the repo, and the script works fine when executed manually. However, when it runs under cron, empty files get dropped into the .git directory. The files have names that look like they are some base64 output, e.g. juTrvjP6m8 and kcKf3hu3b4. Two of these files show up for every cron run. I thought these might be commit hashes, but they're not, git-show says it's an unknown revision. I set-up the repo as follows: git svn init http://svn.ip.addr/repo git svn fetch svn-remote My script looks like this: cd /gitsvn/dir git svn fetch svn-remote git svn push pub The last line pushes the repo to a separate (bare) public repo from which others can clone. I'm piping the output from the cron job to a file, which looks like this: fatal: unable to run 'git-svn' Counting objects: 21, done. Delta compression using up to 2 threads. Compressing objects: 100% (10/10), done. Writing objects: 100% (11/11), 59.08 KiB, done. Total 11 (delta 8), reused 0 (delta 0) To /gitpub/repo.git 360faf5..a153b0d trunk -> trunk The line "fatal: unable to run 'git-svn'" is alarming, but the fetch seems to go ahead anyway. Any suggestions? Where are these empty garbage files coming from, and how to stop them? Am I in for bigger problems in the future? BTW, I'm using git 1.6.3.3.

  Read the article

• Move files and resize partition automatically?

  - by Rob

  I'm in a bit of an odd situation. I've recently been working on switching from debian to arch, and I've got my home partition for both pointing to the same partition (different usernames, so that's not an issue). What I want to do is one of two things, either: Set up user on arch with same username and group as debian, and have everything just sort of work! OR Move files I'd like to share between home folders to their own partition, and mount it with fstab. For the second one, I have around 150gb of files that would need moved to their own partition, and i've got about 15gb of free space on my home partition. So what I'd want to do is somehow make a 10gb ext4 partition, move 10gb-ish of files, expand the partition again, move files again, etc until all the files are moved to their own partition. I can do it manually, but it'd be easier if I could say "Move 10GB-ish of files from here to there, and then resize it and repeat until I'm out of files". Is that even possible?

  Read the article

• rfkill unblock all does not activate a certain wireless card

  - by Davidos

  With an intel 1000 wireless card; rfkill list 0: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: tpacpi_bluetooth_sw: Bluetooth Soft blocked: yes Hard blocked: no rfkill unblock all 0: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 3: hci0: Bluetooth Soft blocked: no Hard blocked: no Why does my wireless card not turn on?

  Read the article

• Can't mount FAT32 drive under Ubuntu Linux

  - by Josh

  I have a 320GB USB drive with a single large FAT32 partition. The volume mounts perfectly fine on my Mac OS X 10.5.8 machine and Disk Utility on the mac reports no issues with the volume. I can read/write all data on the drive. However when I connect the drive to my Ubuntu 9.10 Karmic system, the partition does not mount. dmesg|tail says: [ 2752.334822] scsi3 : SCSI emulation for USB Mass Storage devices [ 2752.335040] usb-storage: device found at 3 [ 2752.335044] usb-storage: waiting for device to settle before scanning [ 2757.330301] usb-storage: device scan complete [ 2757.331005] scsi 3:0:0:0: Direct-Access WD 3200AAK External 1.65 PQ: 0 ANSI: 0 [ 2757.331772] sd 3:0:0:0: Attached scsi generic sg2 type 0 [ 2757.355647] sd 3:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB) [ 2757.360737] sd 3:0:0:0: [sdb] Write Protect is off [ 2757.360749] sd 3:0:0:0: [sdb] Mode Sense: 00 00 00 00 [ 2757.360755] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2757.367618] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2757.367631] sdb: sdb1 [ 2762.797622] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2762.797636] sd 3:0:0:0: [sdb] Attached SCSI disk [ 2822.866228] FAT: bogus number of reserved sectors [ 2822.866237] VFS: Can't find a valid FAT filesystem on dev sdb1. When I run fsck.vfat -a /dev/sdb1 I get: root@cartman:~# fsck.vfat -a /dev/sdb1 dosfsck 3.0.3, 18 May 2009, FAT32, LFN Logical sector size is zero. Googling "vfat Logical sector size is zero" produced no consensus as to the solution. I would prefer not to have to completely reformat the disk if possible because it contains about 280GB of data I would rather not have to find a temporary home for. Any suggestions?

  Read the article

• apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName

  - by user35402

  I keep getting this warning when I (re)start Apache. Restarting web server apache2 apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName ... waiting apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.1.1 for ServerName [ OK ] This is the content of my etc/hosts file: #127.0.0.1 hpdtp-ubuntu910 #testproject.localhost localhost.localdomain localhost #127.0.1.1 hpdtp-ubuntu910 127.0.0.1 localhost 127.0.0.1 testproject.localhost 127.0.1.1 hpdtp-ubuntu910 # The following lines are desirable for IPv6 capable hosts ::1 localhost ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters ff02::3 ip6-allhosts This is the content of my /etc/apache2/sites-enabled/000-default file: <VirtualHost *:80> ServerName testproject.localhost DocumentRoot "/home/morpheous/work/websites/testproject/web" DirectoryIndex index.php <Directory "/home/morpheous/work/websites/testproject/web"> AllowOverride All Allow from All </Directory> Alias /sf /lib/vendor/symfony/symfony-1.3.2/data/web/sf <Directory "/lib/vendor/symfony/symfony-1.3.2/data/web/sf"> AllowOverride All Allow from All </Directory> </VirtualHost> When I go to http://testproject.localhost, I get a blank page can anyone spot what I am doing wrong?

  Read the article

• How do I restart MySQL in monit when page contains specific text?

  - by Tyler

  How do I check if a web page contains the text "Error connecting to database" and if the text exists in the page restart the database? Here's what I have so far but it isn't working: check host website.com with address website.com group database start program = "/usr/bin/service mysql start" stop program = "/usr/bin/service mysql stop" if url http://website.com content == "Error connecting to database" then restart

  Read the article

• "Must have" "Launcher" applications?

  - by levi rosol

  What applications do you use for quickly launching applications, websites, folder paths, etc? Post one application per response, and include a URL.

  Read the article

• Wine and Kernel Access

  - by Kyle Rozendo

  My knowledge on the topic is rather limited, but does one have Kernel access/the general ability to change programs at run time whilst running Wine? For Clarification: Can the user of the computer access any information they want via the Kernel on the underlying system running Wine, or does normal Windows security still apply?

  Read the article

• What is the kernel module "hid_microsoft"?

  - by Masi

  The lsmod-command shows the odd module. The command "modprobe -a hid_microsoft" does not reveal anything. What is it? $ modinfo hid_microsoft filename: /lib/modules/2.6.28-15-generic/kernel/drivers/hid/hid-microsoft.ko license: GPL srcversion: 3FE2E2F2EE89174E885204A alias: hid:b0005v0000045Ep00000701 alias: hid:b0003v0000045Ep0000009D alias: hid:b0003v0000045Ep00000713 alias: hid:b0003v0000045Ep000000F9 alias: hid:b0003v0000045Ep000000DB alias: hid:b0003v0000045Ep0000003B depends: vermagic: 2.6.28-15-generic SMP mod_unload modversions 586

  Read the article

• How to simply remove everything from a directory on Linux

  - by Tometzky

  How to simply remove everything from a current or specified directory on Linux? Several approaches: rm -fr * rm -fr dirname/* Does not work — it will leave hidden files — the one's that start with a dot, and files starting with a dash in current dir, and will not work with too many files rm -fr -- * rm -fr -- dirname/* Does not work — it will leave hidden files and will not work with too many files rm -fr -- * .* rm -fr -- dirname/* dirname/.* Don't try this — it will also remove a parent directory, because ".." also starts with a "." rm -fr * .??* rm -fr dirname/* dirname/.??* Does not work — it will leave files like ".a", ".b" etc., and will not work with too many files find -mindepth 1 -maxdepth 1 -print0 | xargs -0 rm -fr find dirname -mindepth 1 -maxdepth 1 -print0 | xargs -0 rm -fr As far as I know correct but not simple. find -delete find dirname -delete AFAIK correct for current directory, but used with specified directory will delete that directory also. find -mindepth 1 -delete find dirname -mindeph 1 -delete AFAIK correct, but is it the simplest way?

  Read the article

• sudo midnight commander

  - by mit

  I sometimes start midnight commander as superuser with the command sudo mc to do some operations on the current working directory as superuser. But this results in ~/.mc having the wrong permissions, which I need to fix manually. Any solution? Edit: I accepted an answer. I want to further add, that .mc is a directory, so my solution goes like this: $ cd ~ ~$ sudo chown -R mit.mit .mc ~$ chmod 775 .mc ~$ cd .mc ~$ chmod -R 664 .mc ~/.mc$ chmod 775 cedit It seems not to be a good idea after installing mc to use sudo on its first start .

  Read the article

• what does 999 means here

  - by Brij Raj Singh

  I did ll on one of my directories, what does 999 means here, drwxr-xr-x 9 git mysql 4096 Nov 12 14:41 gitlab/ drwxr-xr-x 6 gitlab_ci 999 4096 Jun 28 13:36 gitlabci/ could these directories be fully owned like gitlab is owned by git and gitlabci to be owned by gitlab_ci I want something like this drwxr-xr-x 9 git git 4096 Nov 12 14:41 gitlab/ drwxr-xr-x 6 gitlab_ci gitlab_ci 4096 Jun 28 13:36 gitlabci/

  Read the article

• Broken fonts in Konsole KDE 4.3.4

  - by depesz

  I have a strange situation - after some upgrades a couple of days ago fonts in KDE Konsole broke. To make it more specific - standard fonts look more or less OK, but when I use my national characters (like acelnsózz) they all look broken - like from another font, or badly scaled. The same problem doesn't exist in GNOME Terminal. I usually use the Terminus font, so I used this for demonstration, but it shows in other fonts as well - if that will be necessary I will provide list. Konsole shot: GNOME Terminal shot: As for my settings: =$ cat /etc/X11/xorg.conf Section "Device" Identifier "Builtin Default intel Device 0" Driver "intel" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Monitor Vendor" ModelName "Monitor Model" EndSection Section "Screen" Identifier "Builtin Default intel Screen 0" Device "Builtin Default intel Device 0" Monitor "Monitor0" EndSection Section "InputDevice" Identifier "touchpad" Driver "synaptics" Option "CorePointer" EndSection Section "ServerLayout" Identifier "Builtin Default Layout" Screen "Builtin Default intel Screen 0" InputDevice "touchpad" EndSection =$ xdpyinfo | grep -E resolution\|dimensions dimensions: 1680x1050 pixels (444x277 millimeters) resolution: 96x96 dots per inch I tried forcing DPI in system settings (to 120), or adding monitor size to xorg.conf - so far nothing helped. Any idea on what should I do to make it work sanely again?

  Read the article

< Previous Page | 164 165 166 167 168 169 170 171 172 173 174 175  | Next Page >