Search Results

Search found 31000 results on 1240 pages for 'network design'.

Page 177/1240 | < Previous Page | 173 174 175 176 177 178 179 180 181 182 183 184  | Next Page >

• Raspberry pi slows down my entire network

  - by gnusouth

  Whenever my Raspberry Pi is connected to the network (via ethernet) the entire network is slowed to a crawl. On my main computer, ping times for google.com go from ~10ms to ~200ms and it takes forever to load web pages. Connections are also slow on the Pi, with an apt-get update showing pathetic speeds in the order of 1KB/s. Turning off the Pi completely removes the drag from the network. I've tried static and dynamic IP addresses for the Pi, but both have the same problems. I'm currently using Raspbian (downloaded today), but also had this problem with Arch Linux. I've checked the connection's duplex with dmesg | grep -i duplex, which shows that the Pi's connection is running at 100Mbps, full-duplex, as expected. My modem/router is a Billion 7404VNPX (an Australian thing); relatively high-end, albeit a bit buggy at times (it will occassionally delete all its firewall settings). It assigns IPs in the range 192.168.1.1 to 192.168.1.20 and has 192.168.1.254 as its own IP. When I assign static IPs I tend to use the 192.168.1.200 area. Does anyone have any idea as to what could be causing this weird slowdown? Or any tests I could try? Thanks

  Read the article

• PHP application failed to connect after a network plugged back in

  - by tntu

  My data-center appears to have had some issues with their network and thus my server has suffered from on an off network connectivity for about an hour. After the connection has been completely re-established my code still kept reporting the same issue over and over until I have restarted the service. The code is a simple PHP code that loops forever checking the Apple feed-back server and then sleeps for a few minutes and then it begins all over again. Now I understand the error being generated if the network is down but once it got back up why did it continue until I have restarted the code? Does PHP have something that needs to be re-initialized or something?? Messges log: Dec 20 08:57:22 server kernel: r8169: eth0: link down Dec 20 08:57:28 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:29 server kernel: r8169: eth0: link down Dec 20 08:57:33 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:33 server kernel: r8169: eth0: link down Dec 20 08:57:37 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:38 server kernel: r8169: eth0: link down Dec 20 08:57:44 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:44 server kernel: r8169: eth0: link down Dec 20 08:57:52 server kernel: r8169 0000:06:00.0: eth0: link up Dec 20 08:57:52 server kernel: r8169: eth0: link down Dec 20 09:10:58 server kernel: r8169 0000:06:00.0: eth0: link up PHP Error: PHP Warning: stream_socket_client(): php_network_getaddresses: getaddrinfo failed: Name or service not known in /home/push/feedback.php on line 36 Code Line 36: $apns = stream_socket_client('ssl://feedback.sandbox.push.apple.com:2196', $errcode, $errstr, 60, STREAM_CLIENT_CONNECT, $stream_context);

  Read the article

• Choosing gateway router/firewall for small datacenter network [closed]

  - by rvs

  I'm choosing a gateway router/firewall for small internal network for medium-sized web service. Currently there are 5 servers in internal network, up to 50 http(s) requests/second, up to 1000 simultaneous connections, uplink is 100 Mbit. So, network is relatively small and not very busy and we don't like to buy some pricey monster like cisco or jupiper for this site. Instead we'd like to buy two affordable devices (one for spare), which can handle our workload now and some time in future (it might be up to 2x more in 1 year). I had some experience with Sonicwall NSA, but it seems to be too complex for this site (we don't need most of its features) and even too pricey when buying two of them. So, after some research I've come up with following options: Netgear Prosecure UTM Series (probably UTM25) Zyxel ZyWall Series (USG100 or USG200) Sonicwall TZ 210 Is this a good idea? All of the above seems to be more office products, not datacenter ones. Or we should stick with Sonicwall NSA? Does anyone have any hands-on experience with this models? Maybe some other advices? Thanks.

  Read the article

• Remote network traffic not passing through VPN

  - by John Virgolino

  We have the following topology: LAN A LAN B LAN C 10.14.0.0/16 <-VPN-> 10.18.0.0/16 --- SONICWALL <-VPN-> M0N0WALL --- 10.32.0.0/16 Traffic between LAN A and LAN B works perfectly. Traffic between LAN C and LAN B works perfectly. Traffic between LAN A and LAN C, not so much. LAN A's gateway has a route to LAN C that points to the Sonicwall. The Sonicwall has a route to LAN A pointing to the VPN gateway connecting LAN B to LAN A. Tracing packets on the Sonicwall shows the LAN C destined traffic to arrive on the Sonicwall, but it does not forward the traffic, it dies there. Traffic from LAN B gets forwarded. Tracing packets on the Sonicwall while sending traffic from LAN C destined for LAN A shows nothing. This tells me that the M0N0WALL is not forwarding traffic for the 10.14.0.0 network and the Sonicwall is not forwarding from 10.14.0.0. The SA on the Sonicwall terminates on the WAN ZONE and is defined to use an address group that incorporates both the 10.14.0.0 and 10.18.0.0 networks. The M0N0WALL is configured for the 10.18.0.0 network and I have tried with both a static route to 10.14.0.0 and without on the M0N0WALL. I tried manually adding the 10.14.0.0 network to the SA on the M0N0WALL, but that really aggravated it and the SA never came up, so I reverted. I have checked all the firewall rules to make sure nothing is blocked. All of the Sonicwall auto-added rules look right. Specs: Sonicwall TZ200, Enhanced OS M0N0WALL v1.32 I'm at a loss at this point. Any help would be appreciated.

  Read the article

• pfSense routing between two routers with shared network

  - by JohnCC

  I have a network set-up using two pfSense routers arranged like this:- DMZ1 WAN1 WAN2 DMZ2 | | | | | | | | \___ PF1 PF2___/ | | | | \___TRUSTED___/ Each pfSense router has its own separate WAN connection, and a separate DMZ network attached to it. They share a common TRUSTED LAN between them. The machines on the trusted network have PF1 as their default gateway. PF1 has a static route defined to DMZ2 via PF2, and PF2 has a static route to DMZ1 via PF1. There is NAT to the WAN but internal networks (DMZ1/2 and TRUSTED) use different RFC1918 subnets. I inherited this arrangement, and all used to work fine. I made a config change to PF1 (relating to multicast), and machines on DMZ2 suddenly could not talk to TRUSTED. I rolled the change back, but the problem persisted. What I guess you'd hope would happen is that TCP packets would go DMZ2 - PF2 - TRUSTED and on return TRUSTED - PF1 - PF2 - DMZ2. That's the only way I can see it would have worked. However, PF1 drops the returning packets. I've verified this using tcpdump. I've worked around this by adding static routes to DMZ2 via PF2 to the servers on TRUSTED, but some devices on there do not support static routes so this is not ideal. Is there way to make this arrangement work decently, or is the design inherently flawed? Thanks!

  Read the article

• No network connection for vmware esxi guests

  - by JavaDev

  I'm new to VMware and setting up an Esxi server as a trial with the intention of possibly virtualizing some of our servers in the near future. I have setup ESXi on a Dell poweredge server, and installed a Centos 5.6 and Ubuntu 11.04 guest os on the server. However I cannot get networking on my guest OS's. The host is connected to a network with a DHCP server via a switch and is configured with a static IP. I have the default set-up for networking on the host: both guests are connected to the default vmnic1 adapter via the virtual switch vSwitch0. One thing though, the virtual adapter shows 'Observed IP ranges' to be XXX.XXX.XXX.194-XXX.XXX.XXX.195 (I've blanked out the initial prefixes) i.e just 1 address, even though the network the host is connected to has the usual 255.255.255.0 subnet mask. On the guest machines (using DHCP) by default, I can see an eth0 interface but with no connection or assigned IP address. A physical machine connected to the network gets a DHCP lease as expected. How do I get networking working on my guest OSes? Apologies for the long-winded question.

  Read the article

• Windows 7 'Unidentified Network'

  - by Throdne

  So my internet was working last night before I went to bed and woke up to a computer that is showing unidentified network. I have tried multiple ways of fixing it. > route delete 0.0.0.0 > uninstalling drivers - restart - reinstall from downloaded drivers > ipconfig /release - /renew > static IP > speed & duplex from auto negotiation to 1.0gbps full duplex > and also changed my network address to no value to 1234567890ab (not in that order) nothing seems to work. I have Comcast internet and when I connect the computer to the modem it works perfectly. but when I connect it to my router again, Unidentified network. I know my router isn't faulty, because my macbook pro, server, NAS, iPhones, and iPads are still working. I have also tried moving the port on the router, still same problem. my router is a: Cisco Small Business RVS4000 motherboard: GIGABYTE GA-990FXA-UD3

  Read the article

• Window 7 image in vmware will allow network connection out but not http

  - by Ormis

  I am currently trying to create a set of images to deploy on my network, but I've run in to a snag. When I create my own Windows 7 image I can successfully use NAT for connecting to the network but whenever I try to access a webpage I get nothing. To be more specific, All firewalls/iptables are disabled on my host machine, my virtual machine, and my network. I can do lookups and all addresses respond correctly (i'm even using Google's DNS). On the host OS i have full connectivity. On the virtual machine I can ping any device I want and all addresses resolve correctly. Within a browser I cannot reach any page via hostname or IP. I feel almost like port 80 is being blocked but i can't find any reason this would be the case. If anyone has had this occur before, I would love some insight to the problem. I initially asked this on stackoverflow and now my eyes are now opened up to superuser. Thank you for any help you can provide.

  Read the article

• Windows mounted network drives slow after upgrading switch

  - by Kver

  On our small business network our old 10/100 consumer grade switch gave up the ghost, and we replaced it with a proper business-grade gigabyte switch. After wiring it in our Linux and Mac users immediately got back to working off of network drives; But 2 of our 3 Windows 7 PCs have suddenly experienced a tremendous slowdown with mapped network drives; Windows will become stuck "discovering" a folder causing applications to freeze when trying to open files. It will instantly display and browse files, but the moment you try to open one the bug hits. To remedy this we have our users copying files to the desktop, but it can take a few minutes while windows is stuck "calculating" the time it will take to copy. These aren't big files, mostly excel sheets less than 500KB - these operations are instant on Linux and Mac. (The third Windows machine is having no issues) I've tried remapping the drives, mapping to different drive letters, rebooting, etc. I'm at a loss, because switches are mostly transparent, and it's only after the switch was replaced that the Windows PCs started acting up. What black-magic voodoo am I missing to make Windows work? Thank you.

  Read the article

• Having an issue trying to get Gigabit speed across my network (Ubuntu Server)

  - by user94217

  I've just started looking into the network speeds at my office, the entire network is setup to be "Gigabit". This includes Gb switches, Gb Network cards and Cat 5e cabling. I'm not expecting the full speed, I just want more than ~90 Mb/s. I've been running some tests with iperf the linux tools and checking the hardware with ethtool. I have 3 servers and when doing my checks/test I discovered that the two backup servers can access each other at around 450 Mb/s but when using either one of them to connect and test the main server, I only get the 90Mb/s even though ethtool shows the networking card running at 1000/Full. The only difference between all the server/networking cards is the "Port" which ethtool shows. On the two backup servers the "Port" is shown as MII yet on the other it's shown as "Twisted Pair". When using ethtool -s to manually set the "Port" to MII on the main server, it looses all connectivity and does not show "Speed" or "Duplex". Anyway, Am i doing something wrong? Is there a specific reason my main server cannot use Gb when there appears to be no difference except the "Port"?

  Read the article

• Service redirection on same network

  - by Unode

  I have a network on which I run multiple servers each dedicated to a given service. Because most services run on distinct ports I'm currently looking for a way of unifying "all" services into a single "proxy" machine. The idea is to abstract which machine is being accessed but still allow direct connection if needed/requested. This "proxy" machine has only one network interface which is part of the same network as all the other service providing machines. I've looked into Routing and NAT but I've so far failed to figure out how to make it work. I tried to achieve this using shorewall but couldn't find clear examples. However I'm not entirely sure this is the best/simplest strategy. With that said, what would be the best way of achieving this result? Example case: Proxy IP - Listening port - Send requests to 192.168.0.50 80 192.168.0.1:80 " 22 192.168.0.2:2222 " 3306 192.168.0.3:3000 " 5432 192.168.0.4:5432 " 5222 192.168.0.5:5222 PS: I'm not concerned with the single-point-of-failure nature of the proxy. Thanks

  Read the article

• VirtualBox bridged network not working as expected

  - by iby chenko

  I am having hard time getting Bridged network to work with VirtualBox. Idea is to have host as well as one or more guests on same LAN. Using NAT (default) I do get access to internet and any node on the LAN when working from one of the VM guests. However, no LAN node including host can access (or ping) guest in VM. I need to be able to use any guest as if it was a physical computer on the network (need to be accessed by any machine on LAN). According to my understanding of the VirtualBox documentation, this should be Bridged mode. I think I set it correctly, well, actually there is not much to it: 1. select Bridged mode in VM network setup 2. select physical NIC of the host to connect bridge to 3. start VM When I do this, each VM does get new IP address that corresponds to LAN settings : 192.168.1.100 192.168.1.102 192.168.1.103 etc. where host is 192.168.1.80 / 255.255.255.0 (IP addresses above 100 are served by DHCP server). This seem to be correct based on what I know about ethernet. From VM I can ping other nodes like 192.168.1.50 etc. and I still get ethernet access. So far so good... But I STILL cannot ping any of the other VMs (running ones of course). I cannot ping them from other VMs, from host or from other nodes on the LAN. Aside from fact that IP addresses handed to guests are now local, this still acts same as NAT. What is going on? What am I missing? Regards, I

  Read the article

• how to build network across buildings ?

  - by Omie

  Hi ! I need some help in building a network between hundreds of computers spread across multiple buildings of my college. Yes, I'll be doing this as a part of my college project. Please see this image, it will give you enough idea of what I'm trying to achieve. http://i.imgur.com/rOohx.png All the computers in all buildings should be able to connect server. Once network is up, there will be a set of services over intranet and network use will be moderate. well, say there will be an email server and a http server. My point is, I cannot afford much of performance loss. It feels easy to connect computers inside 1 building to each other, however, I'm clueless as to how to connect all of them to server. I mean, just 1 cable won't be enough to connect 1 building to server, right ? How should I go with it ? I am not expecting detailed configuration. Just heads up will do :) Thanks

  Read the article

• Protocol (or service publish/discovery) to detect devices in network

  - by Gobliins

  we connect some embedded devices in a network. What i am looking for now, is a way to find the devices IP and identify them. We work with Windows PC´s and i am about to write a C# tool that should do this. I thought about send a udp broadcast and in the ack i.e. is the device´s ip, which would mean the device needs a daemon runnig to assign an ip itself. Running a service (like a printer) on the device, and on the PC just lookup for the service. I read about some things like apipa, zeroconf, ipv4 local link, bonjour, dns-sd, mdns, bonjour; They can automatically assign ip´s and publish services in a network. My Question is, can someone recommend me what would be good for my task? -The protocol or Service should be low on ressource (memory/cpu usage) use. -Are there some standard protocolls to use? -Is DNS a good idea or would it be to ressource consumpting just for finding a device´s IP? -Should also work when no dhcp servers are around. edit: To clarify a bit: The IP configuration is automatic. The problem to focus is how to tell the PC which IP in the network (or a direct connection in this vase there would only be one) belongs to the device (identity).

  Read the article

• Can't access apache from outsite my local network

  - by valter

  UPDATED: Now, when I type my external ip like xxx.xxx.xxx.xxx:8079, i can access xampp defaults page. But the strange is that when someone else from outside my network, try to access it using the same ip, it doesnt work. I Think it should, because its the external ip. I'm getting crazy. I have tried for hours to access xampp defaults page from outside my local network. My ISP blocks port 80 and 8080. So I changed apache to listen to port 8079 Listen 8079 My local computer ip is 10.1.1.2 I can access the webserver, from any computer on my local network when I type http://10.1.1.2:8079 I also oppended the port 8079 on my modem, as the image shows bellow. (I think i did it right) When apache is running on my computer, if I test the port 8079 at http://canyouseeme.org/ i get the message "Success: I can see your service on xxx.xxx.xxx.xxx on port (8079) Your ISP is not blocking port 8079" If apache is not running I get "Error: I could not see your service on xxx.xxx.xxx.xxx on port (8079) Reason: Connection refused". So, it's clear that the port 8079 is oppened. But when I type xxx.xxx.xxx.xxx:8079 on google chrome for example, I get Oops! Google Chrome could not connect to xxx.xxx.xxx.xxx:8079 What can I do to solve this, to allow apache to server the pages? I don't know what else I shoud configure. Please, help me. Thanks.

  Read the article

• How do I fix a permissions problem with MS Distributed File System?

  - by charlesrandall

  I have a computer that is new, Windows 7, that is supposed to have access to particular network resources on a Distributed File System. However, despite all permissions being set correctly, I have consistent trouble accessing them. For instance, I'm supposed to be able to reach \company.org\main\subdir. All the permissions have been granted, only when I try to access it by name, it tells me I don't have permission to access \main. This is where the fun starts. If I ping company.org, get the IP, replace company.org by the IP, I can then access \IP\main\subdir without any problems at all. However we have a ton of scripts and build tools that access the network resource by name. My sysadmin has found that using MS's dfsutil.exe, we can fix it temporary using this sequence of commands: C:\dfsutil.exe /pktinfo C:\dfsutil.exe /PktFlush C:\dfsutil.exe /SpcFlush C:\dfsutil.exe /PurgeMupCache C:\dfsutil.exe /pktinfo After that, everything is great... until I reboot, or until some unspecified time later where suddenly I don't have access to \main\ anymore. Hoping to find a more permanent solution than waiting for it to break and running a batch file.

  Read the article

• Computers on network crashing

  - by Phil Cross

  We have recently upgraded our network to Windows 7 clients with Windows server 2008 servers. The upgrade was completed by the end of September and until now has been fine (apart from the minor bugs). Recently (within the last 2 weeks) we've notice all computers on the network (around 1000) start to slow down to the point their unusable. It starts at about 08:45 and finishes at 09:15. Because of this, we think something may be broadcasting across the network. This happens every day, between these times. I cant use my computer at all at the slowdown peak, and looking at task managers performance graphs, Physical memory is hovering around 35% and CPU usage is at 0-10% (idle) yet still crashing. I've looked on DHCPs server log and cant see anything which stands out. The only change we made prior to the slowdown was installing adobe CS6 on some computers, however the slowdown affects computers without CS6. We have 2 physical machines, each with around 5-7 virtual machines running on them with ample memory. Does anyone have any suggestions as to what we can do to narrow down whats causing the crashes? Any help, suggestions or advice would be appreciated.

  Read the article

• Corrupted Laptop - Transfer Data Without My Computer (explorer.exe) Using Command Line

  - by nicorellius

  I have a laptop (Toshiba Satellite) that is pretty messed up. The person this belongs too already replaced it with a new machine. My job is to transfer all her data from this machine to disk so that I can transfer it to her. She doesn't want to lose any data (understandably so). Any operation I attempted (i.e., double clicking on any folder icon, like My Documents, My Computer, etc) resulted din a complete crash. The only good news is that I can actually start and navigate around using the command line. Also, I can access the internet. I have a network, so if I can map the drives I can get this thing figured out (hopefully). Also, I tried a USB drive but I couldn't figure out how to access it from the command line. Two questions (I need to use the command line for these): How would I go about accessing the USB drive and how can I map the shared drives on my network so that I may cd to that directory for use of the copy command?

  Read the article

• How would you rewrite/refactor this ?

  - by frostings

  Old application that is used by 50-60.000 paying customers. Company is several hundred people big. Application has a lot of business critical code (30% of all code) written in classic asp. Application has a lot more .net code. Application has a COM+ bridge for enabling asp to "talk" to .net Organization lacks some/a lot knowledge on what is causing the 10-20% server-reset per day (might be due to COM+ ?) There is no red line through the application; no architecture, no real patterns etc. The application has been like this for at least 5 years. The asp code base is increasing, slowly but certainly. I have read refactoring stories and I have knowledge on why you some of the times should not re-write a system. I would love for the old asp code to vanish as well as the COM+ component. But the pain is that no one really knows what is going on inside the asp classic code and the attitude inside all the teams are "this is just how it is". Down the line, this causes a lot of other issues like recruiting, dev effeciency, business needs that cannot be met, scale etc. With these little facts, does that justify a re-write of the asp code and the removal of the COM+ component ? How would you go about it ?

  Read the article

• How to handle business rules with a REST API?

  - by Ciprio

  I have a REST API to manage a booking system I'm searching how to manage this situation : A customer can book a time slot : A TimeSlot resource is created and linked to a Person resource. In order to create the link between a time lot and a person, the REST client send a POST request on the TimeSlot resource But if too many people booked the same slot (let's say the limit is 5 links), it must be impossible to create more associations. How can I handle this business restriction ? Can I return a 404 status code with a JSON response detailing the error with a status code ? Is it a RESTFul approach ? EDIT : Like suggested below I used status 409 Conflict in addition to a JSON response detailing the error

  Read the article

• What is a "wrapper" program?

  - by user6950

  Where I work, employees use a third-party desktop program for their clients. This program saves data to a flat file. My colleague wants to write a Java program that uploads that flat file to a remote server, opens the desktop program when the flat file is downloaded from a Web site, and checks if the desktop program is running or not by looking at the Windows processes. He keeps calling this helper/utility program a "wrapper." But it doesn't wrap anything! I tried to clear it up with him, but he said, "Well, I call it a wrapper." He now has everyone in the company calling it a "wrapper." What would you call it? I say that it's a helper program or utility program.

  Read the article

• Is a text file with names/pixel locations something a graphic artist can/should produce? [on hold]

  - by edA-qa mort-ora-y

  I have an artist working on 2D graphics for a game UI. He has no problem producing a screenshot showing all the bits, but we're having some trouble exporting this all into an easy-to-use format. For example, take the game HUD, which is a bunch of elements laid out around the screen. He exports the individual graphics for each one, but how should he communicate the positioning of each of them? My desire is to have a yaml file (or some other simple markup file) that contains the name of each asset and pixel position of that element. For example: fire_icon: pos: 20, 30 fire_bar: pos: 30, 80 Is producing such files a common task of a graphic artist? Is is reasonable to request them to produce such files as part of their graphic work?

  Read the article

• Simple ‘In-Progress’ Message for Time Consuming Tasks in ASP.NET Pages

  ‘In-Progress’ Message & Disabling controls in ASP.NET Pages using JavaScript

  Read the article

• Creating site with wix.com or weebly.com [on hold]

  - by Edgar

  I decided to create web page and for that purpose I find out that I can use wix.com portal. My knowledge of HTML,CSS is on basic level. So I want to ask what are pros and cons of creating webPages using WIX to compare with making your on your own (writing code by yourself). One of the questions is: can I put custom advertisements to the my page. Also would appreciate of suggestions what portal is better for wix.com or weebly.com or for good website I should choose codding by myself? Finally, would be nice to get any suggestions in this field.

  Read the article

• How to remove CRUD operations from Entity Class

  - by GlutVonSmark

  Trying to get my head around removing dataStore access from my entity classes. Lets say I have an AccountsGroup entity class. I put the all DBAccess into AccountsGroupRepository class. Now should I have a DeleteFromDB method in the AccountsGroup class, that will call the repository? Public Sub DeleteFromDB dim repository as new AccountsGroupRepository(me) repository.DelteFromDB End Sub Or should I just always use repositry whenever I need to delete an entity, and not have the CRUD methods in the entity class? What happens when there is some business logic validation that needs to be done before the delete can proceed. For example if AccountsGroup still has some Accounts in it the delete method should throw an exception. Where do I put that?

  Read the article

< Previous Page | 173 174 175 176 177 178 179 180 181 182 183 184  | Next Page >