Search Results

Search found 8998 results on 360 pages for 'upgrade failure'.

Page 207/360 | < Previous Page | 203 204 205 206 207 208 209 210 211 212 213 214  | Next Page >

• Laptop crashes when connecting to external harddisk

  - by Gnot

  I recently had a problem with my laptop. when I booted up the machine, I would get a SMART failure error message and when I pressed F1 to continue, it would take a very long time to boot and it would come back to the same error message again. Thinking that my hard disk was dying, I bought a new hard disk and installed on my laptop and so now my laptop is alright. However I need to recover data from that old hard disk, so I bought an external hard disk case and placed the old hard disk onto the case and connected to my laptop with USB. The first few times when I connected, I could see the files from the old hard disk and managed to copy some files over although it took extremely long to transfer. But now whenever I connect to the old hard disk, after a few minutes, my laptop will crash and re-boot. Do you think my old hard disk is dead beyond repair? Or you can offer some help here? Any assistance would be appreciated!

  Read the article

• Windows Media Player functionality for Ubuntu

  - by Xeoncross

  I have way to many music files to bother with setting up playlists. Especially since my files locations keeps changing as I move stuff around and swap between different computers, different mount points, and even different Operating Systems! So managing my media with any application is doomed to failure. However, since I still want to listen to the music I usually just select all the files I want to play at a time and then right-click to open them in a media player. Works great in windows media player and places all the tracks in a temp playlist on the sidebar. Fails in ubuntu using Rhythmbox since it doesn't understand "temp" playlists and just keeps adding files to your FULL listing of all sings on your whole computer. I have over three copies of some tracks now in my audio collection - and all of them are now invalid because the location of the files has changed. So what media player (for Ubuntu) works well with just temporary playlists and will allow me to open up my files without adding them to a collection?

  Read the article

• Disable writing RAID degraded mode

  - by jolivier

  I have a RAID5 with 5 disks on my machine and suspect the motherboard chipset to fail at some points and make my raid going in degraded mode. Last time it happened I noticed it on the failure of the 2nd drive connected to the same chipset and lost a lot of data. So I would like to prevent this, and especially I would like to have mdadm disable writes on the raid if one of the disk fails. So that in between I get notified, I recover and can use my system again. Sadly I could not find it in man mdadm so I was wondering if this is possible via a tool or hidden option since for me it looks like a standard feature of a RAID system. If this is not possible I would also be happy with a solution to stop the raid if degraded.

  Read the article

• New power supply, now computer doesn't recognise hard drive?

  - by Mike

  Ok, I bought a new power supply, because my old one was too damn loud. I hooked it up to my PC, turned it on, everything is looking fine, start up detects my DVD drive, 2 hard disks.. then I get the message "BOOT FAILURE INSERT SYSTEM DISK". Now I've seen some other people talk about going into BIOS and changing the start up to the HDD and not the CD.. well I've done that and it doesn't help. If I let windows load up and it asks me to which partition I wish to install windows, no partition is present. It's as if after the initial start up the drives arn't being found. I plugged my old (but loud) PSU back in, connected up all the cables, and it works perfectly. Why does the new PSU not detect my HDD's after the first BIOS screen start up? Any ideas? :)

  Read the article

• Can I use Veritias Storage Manager to provide HA storage using server-local storage?

  - by Paul

  I have a need to provide an high-availability ftp/http file repository. Upload will happne to one server, but the uploaded file must be immediately visisble on all other servers I can handle the failover of the servers themeselves using load balancers. But in the event of failure of one server, the other servers must see the same contents of the repository. Normally, I'd use a SAN for this, but in this case the data centre standards do not allow SAN/external storage - all storage will be local to the servers. Cam I use Veritas Storage Manager (or any other product) to manage mirroring hte contents between servers in this way? Or does that require a SAN? I couldn't tell either way from a quick look at the data sheets etc.

  Read the article

• APC UPS-5000 Power off remote servers

  - by Vishal

  Hi there, I have a UPS connected via the serial port to a server using PowerChute Business Edition. If a power outage occurs I would like this server to start shutting down all other servers within the network. Is there dedicated software to do this? I was thinking of creating a command file which runs a .bat file to run shut down commands to each server (using PSExec). I can set PowerChute to run this command file when a power failure occurs. Is there not anything APC provide which has this functionality and is more efficient than writing a .bat file to do this? Thanks,

  Read the article

• Windows XP Map drive failed

  - by bajohns

  Greetings, I have a Windows Web Server 2008 VPS and two client machines. One is a Windows 7 box and the other XP. I configured one folder as a share on the 2008 box and attempted to mount it on each of the clients. The catch is it won't work with XP. Same username/password but I get Access granted on the Win 7 but for XP I get: Failure Reason: Unknown user name or bad password. Status: 0xc000006d Any ideas? If this duplicates any other question please refer me but I cannot seem to find the answer.

  Read the article

• Practical way of keeping up-to-date backup servers?

  - by ftkg

  What is the approach generally used when you want to have backup physical servers? Currently I have a Linux server running a database, a samba share, a webapp and some scripts; and a Windows Server, running some third-party software. What I would like was to be able to have a ready backup server to enter in production in case of failure, but how to keep them up-to-date? I've seen some expensive solutions for Windows; for Linux I've wondered if I really have to build an array of scripts.

  Read the article

• Simple Central Storage for HA mail server

  - by jtnire

  Hi Everyone, I will have 2 Postfix servers. One will be a backup of the other. What is the easiest method to provide central storage to both of these boxes? My infrastructure is very simple: Just a lot of Xen hosts, so there is no SAN or anything. Each Xen host does have RAID1 though. I don't mind mounting NFS shares on each of those mail servers, as long as the NFS server wasn't a single point of failure. Is there such a thing as redundant NFS? Any help would be appreciated Thanks

  Read the article

• Installing WiFi in a church for internet access

  - by Dave Griffiths

  Hi, a colleague at work asked this question: My local church want to get WiFi enabled in the whole of their offices and main church building. The offices and main building are in the same overall structure and so the signal does not need to travel outside to any other buildings outside this main structure. Where would I start on such a project and what kind of repeaters are needed (and how are they set up) given that some of the walls are pretty thick. Do you still have one ADSL line coming in to router or are there some options of having two lines coming in so that they isn't a single point of failure. Am looking at fibre for the broadband for increased speed. Any starting pointers appreciated.

  Read the article

• Get off greylisting (the reason why our emails bounced back)

  - by user34402

  Hello, I'm system administrator in online store. We send several emails to our clients after purchase: confirmation, invoice and sale notification to our staff. Recently we got most of emails bounced back and some bounces describes a reason as greylisting, others - just general failure. It is ruining our business because clients are calling that they didn't get the emails with confirmation and invoices. How to get off greylisting, and to not be greylisted? What actions should we do? Mailserver is dedicated machine using Mailenable on Win 2003. Thanks.

  Read the article

• How to take backup mirror copies of C: drive?

  - by metal gear solid

  I've installed everything on my C: Drive . Whatever i need Windows 7, updated drivers and utilities and software etc i need. I now i want to take a backup mirror of everything in a DVD or i can keep backup in another USB HDD. so in case if i face any windows or hard-drive failure in future then i can restore everything as it is as all are today. I don't want to reinstall everything again Windows, Drivers all utilities and all needed soft-wares. My C: Drive's total capacity is 108 GB but data on c: drive is only 12 GB. What Should i do ? What is the best solution for me? I need free solution.

  Read the article

• User account restriction error and unable to access share

  - by user44394

  I have a windows share with full control granted to individual domain user accounts on the share and security permission. Whenever the user attempts to browse to the share they receive the error: Logon failure user account restriction. Possible reasons are blank passwords not allowed, logon hour restrictions, or a policy restriction has been enforced. If the users are added to the administrators group on this machine they are able to browse the share without issue. What do I need to change to allow them access to the share without being administrators on that machine?

  Read the article

• Nagios service active only when other service is failing

  - by Laimoncijus

  Is is possible to define service to be active only the times while other service is failing? Consider following example: 2 hosts available: HostA (primary) and HostB (backup). Nagios service, which monitors amount of active connections to the host: gives OK when amount of connections to host 0 gives FAILURE when amount of connections to host = 0 If setup nagios service to monitor both hosts: HostA and HostB - it will give me OK for HostA (while it is primary and all connections normally goes to it) and FAIL for HostB (while it is backup and will receive no connections while HostA is alive). Can I make the nagios service for HostB somehow depend on sevice of HostA and give no failures (or maybe be inactive) up to the moment the service of HostA starts failing?

  Read the article

• Apache Bench length failures

  - by Laurens

  I am running Apache Bench against a Ruby on Rails XML-RPC web service that is running on Passenger via mod_passenger. All is fine when I run 1000 requests without concurrency. Bench indicates that all requests successfully complete with no failures. When I run Bench again with a concurrency level of 2, however, requests start to fail due to content length. I am seeing failures rates of 70-80% when using concurrency. This should not happen. The requests I am sending to the web service should always results in the same response. I have used cURL to verify that this is in fact the case. My Rails log is not showing any errors as well so I am curious to see what content Bench actually received and interpreted as a failure. Is there any way to print these failures?

  Read the article

• Windows Recovery partition unusable after Ubuntu 12.04 install on Eee PC 1005P

  - by Crivat Camilar

  Installed Ubuntu 12.04 over the secondary (D:) partition with Grub2 handling multi-boot. Never accessed the 'Recovery' option in the boot menu until Windows7 Starter became unusable due to HDD failure (bad sectors on C:). Tried creating an USB recovery stick using the OEM's recovery application (F9) on hidden partition: all I got was a clean C:\ and an error telling me the recovery images cannot be found [R:\recovery\windowsre\ - or something very much like that] although everything is there (changed 'hidden' flag to check and copy contents). Nothing happens upon pressing F9, then Grub takes over giving the recovery option. The application starts but halts about 30s after initializing, very briefly displaying the error message above. I guess every time it goes through this it actually wipes C:\ but crashes immediately afterwards not being able to find what-ever .wim image files it needs. How to make it work?

  Read the article

• Exchange 2007 OWA not listening on SSL port

  - by krs1

  I have an Exchange 2007 server that went down after a power failure. It has OWA access via SSL both externally and internally. OWA is working fine from the internal notwork, however I am getting a timeout when I attempt to connect externally. I pulled up wireshark and noticed that the server actually redirects to SSL. For some reason the server is not listening on the SSL port, and this seems to be causing the timeout. I normally do only development work, but I'm stuck with this since my sysadmin took off for the week and isn't answering my phone calls. As far as I know it shouldn't be a firewall issue. Aside from me not wanting to work on the damn thing, what should I look for?

  Read the article

• "The network path was not found" - shortening the delay before Windows tries again

  - by Harry Johnston

  If I try to connect (over Windows file sharing) to a machine that has gone to sleep, I get a timeout followed by "The network path was not found". If I then wake the machine and try again, I still get "The network path was not found" because the connection failure has been cached. If I wait a while (about 30 seconds?) and then try again I can connect successfully. I understand this behaviour. My question is: is there any way to shorten the delay before I can try the connection again?

  Read the article

• Recently used contacts getting corrupted Outlook 2010

  - by advis12

  We are using Microsoft's Identity Integration Feature Pack to sync contacts between two separate domains at two separate branches of our company. Recently we have run into an issue with a few of the contacts being pulled/synced from this remote location. When people in our organizaion are sending emails to certain contacts that are being synced from the remote location, the message delivery fails. After looking into the issue we are seeing that this failure is the result of the email being sent to some obscure email address rather than the correct email address. For example, the email address is getting changed to IMCEAEX_O=NT5_ou=44C5AE1BBEE0ED499F607407769311BB_cn=2F31FA0CA187314FA8D6A99BEFC52C36@domain.com rather than [email protected] Clearing the recently used contact list seems to solve the issue, but it does not solve the underlying problem. Because this issue is starting to happen to several different people I would like to solve the underlying cause. Does anyone have any input on how to start troubleshooting this issue? Also, we are using Exchange 2010. Thank you for taking the time to look at this.

  Read the article

• Replacing a non-failing drive in a RAID-0 array

  - by TallFurryMan

  I have a Windows 7 machine booting on a RAID-0 pair of 500GB disks, controlled by an ICH9R. One of those was indicating an end-To-end SMART failure, so I added a spare disk as a temporary workaround, before receiving another to replace the failing one. The RAID-0 rebuilt on the spare and dropped the failing one from the array, as expected. Now that I received the new drive, what are my options to reintegrate it in the array? My first thought was to simply clone the temporary disk to the new one while the array is offline, but shouldn't there be a way to force a second rebuild, just as if the temporary drive had a warning, and drop that temporary from the array?

  Read the article

• Cannot login SQL Server after changing machine name

  - by Ucodia

  After installing and setting up new machines in a domain, we decided to rename one of them which had a SQL Server instance installed. So I changed the hostname, everything went fine regarding the domain but now, the server is logging a approximatively 2 SQL Server errors every 5 minutes and I cannot connect to the instance localy or from anywhere within the domain. Here is the error from the event log: SSPI handshake failed with error code 0x8009030c, state 14 while establishing a connection with integrated security; the connection has been closed. Reason: AcceptSecurityContext failed. The Windows error code indicates the cause of failure. The logon attempt failed [CLIENT: x.x.x.x] Concerning the instance, everything is started and restarted without any extra error.

  Read the article

• HDDs randomly falling off raid

  - by michael

  I really need help on this it's Saturday long weekend.No customer service help:( .I recently build new server/light duty desktop.Main purpose is only file sharing.Raid configuration :Adaptec 6805 ,8x 3TB HDD WD Red,Intel RES2SV240 expander,Raid 6,set in Intel mobo DZ 77GA-70K.I upgraded firmwares, but I'm having strange problem. During Build Verify segment 7 got missing.I just reinsert drive into hot swap bay and it started to rebuild Array.After rebuild was done another segments 0 and 5 gone missing while build/verify.I reinserted drives and now I'm praying that raid is going to rebuild successfully from remaining 6 drives,because i already transfer some data on it(I know it was bad idea).I checked S.M.A.R.T on missing drives , it only says link failure and aborted commands on one of them.No Errors on HDDs.Connections and cables are good.I added 2 fans blowing on RAID controller because it was getting too hot, so I guess overheating shouldn't be issue.What can be possibly wrong? Thank you for help.

  Read the article

• Windows/Samba connection error

  - by Gomibushi

  I have a Linux fileserver serving up /home for linux and windows users. I was able to connect from my windows client, but not from a DC. Then suddenly I could connect from the DC too. The linux servers run Centrify clients, and as such are part of the domain. All on same subnet. This is what the the log.smbd says, repeatedly: [2010/02/11 11:25:57, 0] lib/util_sock.c:read_data(534) read_data: read failure for 4 bytes to client 192.168.200.3. Error = Connection reset by peer On Windows it appeared as an "unknown error". EDIT: the error code is "0x80004005". We are developing a system depended on the samba share, and are worried this will appear again. It would be nice to pin point the root of this. Any ideas what this might be? Places to look?

  Read the article

• server down "without reason"

  - by Nick

  I have a Lenny dedicated server at Hivelocity. My server went down today. They doesn't know why. I don't know why. MTRG shows 7Mbps before went the server goes offline, ddos not probably. Hardware failure? maybe. but now is running ok. hacked? maybe. lastlog, md5sum, rkhunter, syslog and auth.log seems ok. my load is always between 0.02 and 0.3, the server runs a small website but with 2million pageviews/day and never failed before. Where can I find more information in my logs? where I start looking?

  Read the article

• Sql database dumps failing every night

  - by chaseman36

  Hey guys, I have sql05 and my maintenance plan which backs up a database to an external storage SAN, has been failing every night. Here is my error: Executing the query "BACKUP DATABASE [master] TO DISK = N'\\192.168.x.x\vmbackup\server\dbbackup\master_backup_201004222300.bak' WITH NOFORMAT, NOINIT, NAME = N'master_backup_20100422230002', SKIP, REWIND, NOUNLOAD, STATS = 10 " failed with the following error: "Cannot open backup device '\\192.168.x.x\vmbackup\server\dbbackup\master_backup_201004222300.bak'. Operating system error 5(Access is denied.). BACKUP DATABASE is terminating abnormally.". Possible failure reasons: Problems with the query, "ResultSet" property not set correctly, parameters not set correctly, or connection not established correctly. I googled this error and tried adding permissions to the backup device for network service as recommended at experts exchange, no dice. Does anyone have any ideas?

  Read the article

< Previous Page | 203 204 205 206 207 208 209 210 211 212 213 214  | Next Page >