Search Results

Search found 20847 results on 834 pages for 'advanced computer science'.

Page 230/834 | < Previous Page | 226 227 228 229 230 231 232 233 234 235 236 237  | Next Page >

• Bypass BIOS password set by faulty Toshiba firmware on Satellite A55 laptop?

  - by Brian

  How can the CMOS be cleared on the Toshiba Satellite A55-S1065? I have this 7 year old laptop that has been crippled by a glitch in its BIOS: 'A "Password =" prompt may be displayed when the computer is turned on, even though no power-on password has been set. If this happens, there is no password that will satisfy the password request. The computer will be unusable until this problem is resolved. [..] The occurrence of this problem on any particular computer is unpredictable -- it may never happen, but it could happen any time that the computer is turned on. [..] Toshiba will cover the cost of this repair under warranty until Dec 31, 2010.' -Toshiba As they stated, this machine is "unusable." The escape key does not bypass the prompt (nor does any other key), thus no operating system can be booted and no firmware updates can be installed. After doing some research, I found solutions that have been suggested for various Toshiba Satellite models afflicted by this glitch: "Make arrangements with a Toshiba Authorized Service Provider to have this problem resolved." -Toshiba (same link). Even prior to the expiration of Toshiba's support ("repair under warranty until Dec 31, 2010"), there have been reports that this solution is prohibitively expensive, labor charges accruing even when the laptop is still under warranty, and other reports that are generally discouraging: "They were unable to fix it and the guy who worked on it said he couldn’t find the jumpers on the motherboard to clear the BIOS. I paid $39 for my troubles and still have the password problem." - Steve. Since the costs of the repairs can now exceed the value of the hardware, it would seem this is a DIY solution, or a non-solution (i.e. the hardware is trash). Build a Toshiba parallel loopback by stripping and soldering the wires on a DB25 plug to connect connect these pins: 1-5-10, 2-11, 3-17, 4-12, 6-16, 7-13, 8-14, 9-15, 18-25. -CGSecurity. According to a list of supported models on pwcrack, this will likely not work for my Satellite A55-1065 (as well as many other models of similar age). -pwcrack Disconnect the laptop battery for an extended period of time. Doesn't work, laptop sat in a closet for several years without the battery connected and I forgot about the whole thing for awhile. The poor thing. Clear CMOS by setting the proper jumper setting or by removing the CMOS (RTC) battery, or by short circuiting a (hidden?) jumper that looks like a pair of solder marks -various sources for various Satellite models: Satellite A105: "you will see C88 clearly labeled right next the jack that the wireless card plugs into. There are two little solder squares (approx 1/16") at this location" -kerneltrap Satellite 1800: "Underneath the RAM there is black sticker, peel off the black sticker and you will reveal two little solder marks which are actually 'jumpers'. Very carefully hold a flat-head screwdriver touching both points and power on the unit briefly, effectively 'shorting' this circuit." -shadowfax2020 Satellite L300: "Short the B500 solder pads on the system board." -Lester Escobar Satellite A215: "Short the B500 solder pads on the system board." -fixya Clearing the CMOS could resolve the issue, but I cannot locate a jumper or a battery on this board. Nothing that looks remotely like a battery can be removed (everything is soldered). I have looked closely at the area around the memory and do not see any obvious solder pads that could be a secret jumper. Here are pictures (click for full resolution) : Where is the jumper (or solder pads) to short circuit and wipe the CMOS on this board? Possibly related questions: Remove Toshiba laptop BIOS password? Password Problem Toshiba Satellite..

  Read the article

• Do We Indeed Have a Future? George Takei on Star Wars.

  - by Bil Simser

  George Takei (rhymes with Okay), probably best known for playing Hikaru Sulu on the original Star Trek, has always had deep concerns for the present and the future. Whether on Earth or among the stars, he has the welfare of humanity very much at heart. I was digging through my old copies of Famous Monsters of Filmland, a great publication on monster and films that I grew up with, and came across this. This was his reaction to STAR WARS from issue 139 of Famous Monsters of Filmland and was written June 6, 1977. It is reprinted here without permission but I hope since the message is still valid to this day and has never been reprinted anywhere, nobody will mind me sharing it. STAR WARS is the most pre-posterously diverting galactic escape and at the same time the most hideously credible portent of the future yet.While I thrilled to the exploits that reminded me of the heroics of Errol Flynn as Robin Hood, Burt Lancaster as the Crimson Pirate and Buster Crabbe as Flash Gordon, I was at the same time aghast at the phantasmagoric violence technology can place at our disposal. STAR WARS raised in my mind the question - do we indeed have a future?It seems to me what George Lucas has done is to masterfully guide us on a journey through space and time and bring us back face to face with today's reality. STAR WARS is more than science fiction, I think it is science fictitious reality.Just yesterday, June 7, 1977, I read that the United States will embark on the production of a neutron bomb - a bomb that will kill people on a gigantic scale but will not destroy buildings. A few days before that, I read that the Pentagon is fearful that the Soviets may have developed a warhead that could neutralize ours that have a capacity for that irrational concept overkill to the nth power. Already, it seems we have the technology to realize the awesome special effects simulations that we saw in the film.The political scene of STAR WARS is that of government by force and power, of revolutions based on some unfathomable grievance, survival through a combination of cunning and luck and success by the harnessing of technology -  a picture not very much at variance from the political headlines that we read today.And most of all, look at the people; both the heroes in the film and the reaction of the audience. First, the heroes; Luke Skywalker is a pretty but easily led youth. Without any real philosophy to guide him, he easily falls under the influence of a mystical old man believed previously to be an eccentric hermit. Recognize a 1960's hippie or a 1970's moonie? Han Solo has a philosophy coupled with courage and skill. His philosophy is money. His proficiency comes for a price - the highest. Solo is a thoroughly avaricious mercenary. And the Princess, a decisive, strong, self-confident and chilly woman. The audience cheered when she wielded a gun. In all three, I missed qualities that could be called humane - love, kindness, yes, I missed sensuality. I also missed a sense of ideals and faith. In this regard the machines seemed more human. They demonstrated real affection for each other and an occasional poutiness. They exhibited a sense of fidelity and constancy. The machines were humanized and the humans conversely seemed mechanical.As a member of the audience, I was swept up by the sheer romantic escapsim of it all. The deering-dos, the rope swing escape across the pit, the ray gun battles and especially the swash buckle with the ray swords. Great fun!But I just hope that we weren't too intoxicated by the escapism to be able to focus on the recognizable. I hope the beauty of the effects didn't narcotize our sensitivity to violence. I hope the people see through the fantastically well done futuristic mirrors to the disquieting reflection of our own society. I hope they enjoy STAR WARS without being "purely entertained".

  Read the article

• CodePlex Daily Summary for Wednesday, June 02, 2010

  CodePlex Daily Summary for Wednesday, June 02, 2010New ProjectsBackupCleaner.Net: A C#.Net-based tool for automatically removing old backups selectively. It can be used when you already make daily backups on disk, and want to cle...C# Dotnetnuke Module development Template for Visual Studio 2010: C# DNN Module Development template for Visual Studio 2010 Get a head-start on DNN Module development. Whether you're a pro or just starting with D...Christoc's DotNetNuke C# Module Development Template: A quick and easy to use C# Module development template for DotNetNuke 5, Visual Studio 2008.Client per la digitalizzazione di documenti integrato con DotNetNuke: Questo applicativo in ambiente windows 32bit consente di digitalizzare documenti con piu scanner contemporaneamente, processare OCR in 17 Lingue (p...ContainerOne - C# application server: An application server completely written in c# (.net 4.0).Drop7 Silverlight: It's a clone of the original Drop7 written in Silverlight (C#). Echo.Net: Echo.Net is an embedded task manager for web and windows apps. It allows for simple management of background tasks at specific times. It's develope...energy: Smartgrid Demand Response ImplementationGenerate Twitter Message for Live Writer: This is a plug-in for Windows Live Writer that generates a twitter message with your blog post name and a TinyUrl link to the blog post. It will d...HomingCMS.Net: A lightweight cms.Information Système & Shell à distance: Un web service qui permet d'avoir des informations sur le système et de lancer de commande (terminal) à distance.Javascript And Jquery: gqq's javascript and jquery examplesMemory++: "Tweak the memory to speed up your computer" Memory ++ is basically an application that will speed up your computer ensuring comfort in their norma...Microformat Parsers for .NET: Microformat's Parsers for .NET helps you to collect information you run into on the web, that is stored by means of microformats. It's written in C...MoneyManager: Trying to make Personal Finances management System for my needs. Microsoft stopped to support MSMoney - it makes me so sad, so I wanna to make my ...Open source software for running a financial markets trading business: The core conceptual model will support running a business in the financial markets, for example running a trading exchange business.Ovik: Open Video Converter with simple and intuitive interface for converting video files to the open formats.Oxygen Smil Player: The <project name> is a open a-smil player implementation that is meaned to be connected to a Digital Signage CMS like Oxygen media platform ( www....Protect The Carrot: Protect The Carrot is a small fastpaced XNA game. You are a farmer whose single carrot is under attack by ravenous rabbits. You have to shoot the r...Race Day Commander: The core project is designed to support coaches of "long distance" or "endurance" sporting events coach their athletes during a race. The idea bein...Raygun Diplomacy: Raygun Diplomacy is an action shooter sandbox game set in a futuristic world. It will use procedural generation for the world, weapons, and vehicle...Resx-Translator-Bot: Resx-Translator-Bot uses Google Tanslate to automatically translate the .resx-files in your .NET and ASP.NET applications.Sistema de Expedición del Permiso Único de Siembra: Sistema de Expedición del Permiso Único de Siembra.SiteOA: 一个基于asp.net mvc2的OAStraighce: This is a low-featured, cyclic (log files reside in appname\1.txt to at mose 31.txt), thread-safe and non-blocking TraceListener with some extensio...Touch Mice: Touch Mice turns multiple mice on a computer into individual touch devices. This allows you to create multi-touch applications using the new touch...TStringValidator: A project helper to validate strings. Use this class to hold your regex strings for use with any project's string validation.Ultimate Dotnetnuke Skin Object: Ultimate Skin Object is a Dotnetnuke 5.4.2+ extension that will allow you to easily change your skins doc type, remove unneeded css files, inject e...Ventosus: Ventosus is an upcoming partially text-based game. No further information is available at this time.vit: vit based on asp.net mvcW7 Auto Playlist Generator: Purpose: This application is designed to create W7MC playlist automatically whenever you want. You can select if you want the playlist sorted Alpha...W7 Video Playlist Creator: Purpose: This program allows you to quickly create wvx video play list for Windows Media Center. This functionality is not included in WMC and is u...New ReleasesBCryptTool: BCryptTool v0.2.1: The Microsoft .NET Framework 4.0 is needed to run this program.BFBC2 PRoCon: PRoCon 0.5.2.0: Notes available on phogue.netC# Dotnetnuke Module development Template for Visual Studio 2010: DNNModule 1.0: This is the initial release of DNNModule as was available for download from http://www.subodh.com/Projects/DNNModule In this release: Contains one...Client per la digitalizzazione di documenti integrato con DotNetNuke: Versione 3.0.1: Versione 3.0.1CommonLibrary.NET: CommonLibrary.NET 0.9.4 - Final Release: A collection of very reusable code and components in C# 3.5 ranging from ActiveRecord, Csv, Command Line Parsing, Configuration, Holiday Calendars,...Community Forums NNTP bridge: Community Forums NNTP Bridge V20: Release of the Community Forums NNTP Bridge to access the social and anwsers MS forums with a single, open source NNTP bridge. This release has ad...Community Forums NNTP bridge: Community Forums NNTP Bridge V21: Release of the Community Forums NNTP Bridge to access the social and anwsers MS forums with a single, open source NNTP bridge. This release has ad...DirectQ: Release 1.8.4: Significant bug fixes and improvments over 1.8.3c; there may be some bugs that I haven't caught here as development became a little disjointed towa...DotNetNuke 5 Thai Language Pack: 1.0.1: Fixed Installation Problem. Version 1.0 -> 1.0.1 Type : Character encoding. Change : ().dnn description file to "ไทย (ไทย)".dnnEcho.Net: Echo.Net 1.0: Initial release of Echo.Net.Extend SmallBasic: Teaching Extensions v.018: ShapeMaker, Program Window, Timer, and many threading errors fixedExtend SmallBasic: Teaching Extensions v.019: Added Rectangles to shapemaker, and the bubble quizGenerate Twitter Message for Live Writer: Final Source Code Plus Binaries: Compete C# source code available below. I have also included the binary for those that just want to run it.GoogleMap Control: GoogleMap Control 4.5: Map and map events are only functional. New state, persistence and event implementation in progress. Javascript classes are implemented as MS AJAX ...Industrial Dashboard: ID 3.1: -Added new widget IndustrialSlickGrid. -Added example with IndustrialChart.LongBar: LongBar 2.1 Build 310: - Library: Double-clicking on tile will install it - Feedback: Now you can type your e-mail and comment for errorMavention: Mavention Insert Lorem ipsum: A Sandbox Solution for SharePoint 2010 that allows you to easily insert Lorem ipsum text into RTE. More information and screenshots available @ htt...Memory++: Memory ++: Tweak the memory to speed up your computer Memory is basically an application that will speed up your computer ensuring comfort in their normal ac...MyVocabulary: Version 2.0: Improvements over version 1.0: Several bug fixes New shortcuts added to increase usability A new section for testing verbs was addednopCommerce. Open Source online shop e-commerce solution.: nopCommerce 1.60: You can also install nopCommerce using the Microsoft Web Platform Installer. Simply click the button below: nopCommerce To see the full list of f...Nuntio Content: Nuntio Content 4.2.1: Patch release that fixes a couple of minor issues with version numbers and priority settings for role content. The release one package for DNN 4 an...Ovik: Ovik v0.0.1 (Preview Release): This is a very early preview release of Ovik. It contains only the pure processes of selecting files and launching a conversion process. Preview r...PHPExcel: PHPExcel 1.7.3c Production: This is a patch release for 26477. Want to contribute?Please refer the Contribute page. DonationsDonate via PayPal. If you want to, we can also a...PowerShell Admin Modules: PAM 0.2: Version 0.2 contains the PAMShare module with Get-Share Get-ShareAccessMask Get-ShareSecurity New-Share Remove-Share Set-Share and the PAMath modu...Professional MRDS: RDS 2008 R3 Release: This is an updated version of the code to work with RDS 2008 R3 (version 2.2.76.0). IMPORTANT NOTE These samples are supplied as a ZIP file. Unzip...Protect The Carrot: First release: We provide two ways to install the game. The first is PTC 1.0.0.0 Zip which contains a Click-Once installer (the DVD type since codeplex does not...PST File Format SDK: PST File Format SDK v0.2.0: Updated version of pstsdk with several bug fixes, including: Improved compiler support (several changes, including two patches from hub) Fixed Do...Race Day Commander: Race Day Commander v1: First release. The exact code that was written on the day in 6 hours.Resx-Translator-Bot: Release 1.0: Initial releaseSalient.StackApps: JavaScript API Wrapper beta 2: This is the first draft of the generated JS wrapper. Added basic test coverage for each route that can also serve as basic usage examples. More i...SharePoint 2010 PowerShell Scripts & Utilities: PSSP2010 Utils 0.2: Added Install-SPIFilter script cmdlet More information can be found at http://www.ravichaganti.com/blog/?p=1439SharePoint Tools from China Community: ECB菜单控制器: ECB菜单控制器Shopping Cart .NET: 1.5: Shopping Cart .NET 1.5 has received an upgrade to .NET 4.0 along with SQL Server 2005/8. There is a new AJAX Based inventory system that helps you ...sMODfix: sMODfix v1.0b: Added: provisional support for ecm_v54 Added: provisional support for gfx_v88SNCFT Gadget: SNCFT gadget v1: cette version est la version 1 de ma gadgetSnippet Designer: Snippet Designer 1.3: Change logChanges for Visual Studio 2010Fixed bug where "Export as Snippet" was failing in a website project Changed Snippet Explorer search to u...sNPCedit: sNPCedit v0.9b: + Fixed: structure of resources + Changed: some labels in GUISoftware Is Hardwork: Sw. Is Hw. Lib. 3.0.0.x+05: Sw. Is Hw. Lib. 3.0.0.x+05SQL Server PowerShell Extensions: 2.2.3 Beta: Release 2.2 re-implements SQLPSX as PowersShell version 2.0 modules. SQLPSX consists of 9 modules with 133 advanced functions, 2 cmdlets and 7 scri...StackOverflow.Net: Preview Beta: Goes with the Stack Apps API version 0.8Ultimate Dotnetnuke Skin Object: Ultimate Skin Object V1.00.00: Ultimate Skin Object is a Dotnetnuke 5.4.2+ extension that will allow you to easily change your skins doc type, remove unneeded css files, inject e...VCC: Latest build, v2.1.30601.0: Automatic drop of latest buildVelocity Shop: JUNE 2010: Source code aligned to .NET Framework 4.0, ASP.NET 4.0 and Windows Server AppFabric Caching RC.ViperWorks Ignition: ViperWorks_5.0.1005.31: ViperWorks Ignition Source, version 5.0.1005.31.Visual Studio 2010 and Team Foundation Server 2010 VM Factory: Session Recordings: This release contains the "raw" and undedited session recordings and slides delivered by the team. 2010-06-01 Create package and add two session r...W7 Auto Playlist Generator: Source Code plus Binaries: Compete C# and WinForm source code available below. I have also included the binary for those that just want to run it.W7 Video Playlist Creator: Source Code plus Binaries: Compete C# and WPF source code available below. I have also included the binary for those that just want to run it.Most Popular ProjectsRawrWBFS ManagerAJAX Control ToolkitMicrosoft SQL Server Product Samples: DatabaseSilverlight ToolkitWindows Presentation Foundation (WPF)patterns & practices – Enterprise LibraryPHPExcelMicrosoft SQL Server Community & SamplesASP.NETMost Active ProjectsCommunity Forums NNTP bridgepatterns & practices – Enterprise LibraryGMap.NET - Great Maps for Windows Forms & PresentationBlogEngine.NETIonics Isapi Rewrite FilterMirror Testing SystemRawrCaliburn: An Application Framework for WPF and SilverlightPHPExcelCustomer Portal Accelerator for Microsoft Dynamics CRM

  Read the article

• Oracle Solaris: Zones on Shared Storage

  - by Jeff Victor

  Oracle Solaris 11.1 has several new features. At oracle.com you can find a detailed list. One of the significant new features, and the most significant new feature releated to Oracle Solaris Zones, is casually called "Zones on Shared Storage" or simply ZOSS (rhymes with "moss"). ZOSS offers much more flexibility because you can store Solaris Zones on shared storage (surprise!) so that you can perform quick and easy migration of a zone from one system to another. This blog entry describes and demonstrates the use of ZOSS. ZOSS provides complete support for a Solaris Zone that is stored on "shared storage." In this case, "shared storage" refers to fiber channel (FC) or iSCSI devices, although there is one lone exception that I will demonstrate soon. The primary intent is to enable you to store a zone on FC or iSCSI storage so that it can be migrated from one host computer to another much more easily and safely than in the past. With this blog entry, I wanted to make it easy for you to try this yourself. I couldn't assume that you have a SAN available - which is a good thing, because neither do I! What could I use, instead? [There he goes, foreshadowing again... -Ed.] Developing this entry reinforced the lesson that the solution to every lab problem is VirtualBox. Oracle VM VirtualBox (its formal name) helps here in a couple of important ways. It offers the ability to easily install multiple copies of Solaris as guests on top of any popular system (Microsoft Windows, MacOS, Solaris, Oracle Linux (and other Linuxes) etc.). It also offers the ability to create a separate virtual disk drive (VDI) that appears as a local hard disk to a guest. This virtual disk can be moved very easily from one guest to another. In other words, you can follow the steps below on a laptop or larger x86 system. Please note that the ability to use ZOSS to store a zone on a local disk is very useful for a lab environment, but not so useful for production. I do not suggest regularly moving disk drives among computers. In the method I describe below, that virtual hard disk will contain the zone that will be migrated among the (virtual) hosts. In production, you would use FC or iSCSI LUNs instead. The zonecfg(1M) man page details the syntax for each of the three types of devices. Why Migrate? Why is the migration of virtual servers important? Some of the most common reasons are: Moving a workload to a different computer so that the original computer can be turned off for extensive maintenance. Moving a workload to a larger system because the workload has outgrown its original system. If the workload runs in an environment (such as a Solaris Zone) that is stored on shared storage, you can restore the service of the workload on an alternate computer if the original computer has failed and will not reboot. You can simplify lifecycle management of a workload by developing it on a laptop, migrating it to a test platform when it's ready, and finally moving it to a production system. Concepts For ZOSS, the important new concept is named "rootzpool". You can read about it in the zonecfg(1M) man page, but here's the short version: it's the backing store (hard disk(s), or LUN(s)) that will be used to make a ZFS zpool - the zpool that will hold the zone. This zpool: contains the zone's Solaris content, i.e. the root file system does not contain any content not related to the zone can only be mounted by one Solaris instance at a time Method Overview Here is a brief list of the steps to create a zone on shared storage and migrate it. The next section shows the commands and output. You will need a host system with an x86 CPU (hopefully at least a couple of CPU cores), at least 2GB of RAM, and at least 25GB of free disk space. (The steps below will not actually use 25GB of disk space, but I don't want to lead you down a path that ends in a big sign that says "Your HDD is full. Good luck!") Configure the zone on both systems, specifying the rootzpool that both will use. The best way is to configure it on one system and then copy the output of "zonecfg export" to the other system to be used as input to zonecfg. This method reduces the chances of pilot error. (It is not necessary to configure the zone on both systems before creating it. You can configure this zone in multiple places, whenever you want, and migrate it to one of those places at any time - as long as those systems all have access to the shared storage.) Install the zone on one system, onto shared storage. Boot the zone. Provide system configuration information to the zone. (In the Real World(tm) you will usually automate this step.) Shutdown the zone. Detach the zone from the original system. Attach the zone to its new "home" system. Boot the zone. The zone can be used normally, and even migrated back, or to a different system. Details The rest of this shows the commands and output. The two hostnames are "sysA" and "sysB". Note that each Solaris guest might use a different device name for the VDI that they share. I used the device names shown below, but you must discover the device name(s) after booting each guest. In a production environment you would also discover the device name first and then configure the zone with that name. Fortunately, you can use the command "zpool import" or "format" to discover the device on the "new" host for the zone. The first steps create the VirtualBox guests and the shared disk drive. I describe the steps here without demonstrating them. Download VirtualBox and install it using a method normal for your host OS. You can read the complete instructions. Create two VirtualBox guests, each to run Solaris 11.1. Each will use its own VDI as its root disk. Install Solaris 11.1 in each guest.Install Solaris 11.1 in each guest. To install a Solaris 11.1 guest, you can either download a pre-built VirtualBox guest, and import it, or install Solaris 11.1 from the "text install" media. If you use the latter method, after booting you will not see a windowing system. To install the GUI and other important things, login and run "pkg install solaris-desktop" and take a break while it installs those important things. Life is usually easier if you install the VirtualBox Guest Additions because then you can copy and paste between the host and guests, etc. You can find the guest additions in the folder matching the version of VirtualBox you are using. You can also read the instructions for installing the guest additions. To create the zone's shared VDI in VirtualBox, you can open the storage configuration for one of the two guests, select the SATA controller, and click on the "Add Hard Disk" icon nearby. Choose "Create New Disk" and specify an appropriate path name for the file that will contain the VDI. The shared VDI must be at least 1.5 GB. Note that the guest must be stopped to do this. Add that VDI to the other guest - using its Storage configuration - so that each can access it while running. The steps start out the same, except that you choose "Choose Existing Disk" instead of "Create New Disk." Because the disk is configured on both of them, VirtualBox prevents you from running both guests at the same time. Identify device names of that VDI, in each of the guests. Solaris chooses the name based on existing devices. The names may be the same, or may be different from each other. This step is shown below as "Step 1." Assumptions In the example shown below, I make these assumptions. The guest that will own the zone at the beginning is named sysA. The guest that will own the zone after the first migration is named sysB. On sysA, the shared disk is named /dev/dsk/c7t2d0 On sysB, the shared disk is named /dev/dsk/c7t3d0 (Finally!) The Steps Step 1) Determine the name of the disk that will move back and forth between the systems. root@sysA:~# format Searching for disks...done AVAILABLE DISK SELECTIONS: 0. c7t0d0 /pci@0,0/pci8086,2829@d/disk@0,0 1. c7t2d0 /pci@0,0/pci8086,2829@d/disk@2,0 Specify disk (enter its number): ^D Step 2) The first thing to do is partition and label the disk. The magic needed to write an EFI label is not overly complicated. root@sysA:~# format -e c7t2d0 selecting c7t2d0 [disk formatted] FORMAT MENU: ... format fdisk No fdisk table exists. The default partition for the disk is: a 100% "SOLARIS System" partition Type "y" to accept the default partition, otherwise type "n" to edit the partition table. n SELECT ONE OF THE FOLLOWING: ... Enter Selection: 1 ... G=EFI_SYS 0=Exit? f SELECT ONE... ... 6 format label ... Specify Label type[1]: 1 Ready to label disk, continue? y format quit root@sysA:~# ls /dev/dsk/c7t2d0 /dev/dsk/c7t2d0 Step 3) Configure zone1 on sysA. root@sysA:~# zonecfg -z zone1 Use 'create' to begin configuring a new zone. zonecfg:zone1 create create: Using system default template 'SYSdefault' zonecfg:zone1 set zonename=zone1 zonecfg:zone1 set zonepath=/zones/zone1 zonecfg:zone1 add rootzpool zonecfg:zone1:rootzpool add storage dev:dsk/c7t2d0 zonecfg:zone1:rootzpool end zonecfg:zone1 exit root@sysA:~# oot@sysA:~# zonecfg -z zone1 info zonename: zone1 zonepath: /zones/zone1 brand: solaris autoboot: false bootargs: file-mac-profile: pool: limitpriv: scheduling-class: ip-type: exclusive hostid: fs-allowed: anet: ... rootzpool: storage: dev:dsk/c7t2d0 Step 4) Install the zone. This step takes the most time, but you can wander off for a snack or a few laps around the gym - or both! (Just not at the same time...) root@sysA:~# zoneadm -z zone1 install Created zone zpool: zone1_rpool Progress being logged to /var/log/zones/zoneadm.20121022T163634Z.zone1.install Image: Preparing at /zones/zone1/root. AI Manifest: /tmp/manifest.xml.RXaycg SC Profile: /usr/share/auto_install/sc_profiles/enable_sci.xml Zonename: zone1 Installation: Starting ... Creating IPS image Startup linked: 1/1 done Installing packages from: solaris origin: http://pkg.us.oracle.com/support/ DOWNLOAD PKGS FILES XFER (MB) SPEED Completed 183/183 33556/33556 222.2/222.2 2.8M/s PHASE ITEMS Installing new actions 46825/46825 Updating package state database Done Updating image state Done Creating fast lookup database Done Installation: Succeeded Note: Man pages can be obtained by installing pkg:/system/manual done. Done: Installation completed in 1696.847 seconds. Next Steps: Boot the zone, then log into the zone console (zlogin -C) to complete the configuration process. Log saved in non-global zone as /zones/zone1/root/var/log/zones/zoneadm.20121022T163634Z.zone1.install Step 5) Boot the Zone. root@sysA:~# zoneadm -z zone1 boot Step 6) Login to zone's console to complete the specification of system information. root@sysA:~# zlogin -C zone1 Answer the usual questions and wait for a login prompt. Then you can end the console session with the usual "~." incantation. Step 7) Shutdown the zone so it can be "moved." root@sysA:~# zoneadm -z zone1 shutdown Step 8) Detach the zone so that the original global zone can't use it. root@sysA:~# zoneadm list -cv ID NAME STATUS PATH BRAND IP 0 global running / solaris shared - zone1 installed /zones/zone1 solaris excl root@sysA:~# zpool list NAME SIZE ALLOC FREE CAP DEDUP HEALTH ALTROOT rpool 17.6G 11.2G 6.47G 63% 1.00x ONLINE - zone1_rpool 1.98G 484M 1.51G 23% 1.00x ONLINE - root@sysA:~# zoneadm -z zone1 detach Exported zone zpool: zone1_rpool Step 9) Review the result and shutdown sysA so that sysB can use the shared disk. root@sysA:~# zpool list NAME SIZE ALLOC FREE CAP DEDUP HEALTH ALTROOT rpool 17.6G 11.2G 6.47G 63% 1.00x ONLINE - root@sysA:~# zoneadm list -cv ID NAME STATUS PATH BRAND IP 0 global running / solaris shared - zone1 configured /zones/zone1 solaris excl root@sysA:~# init 0 Step 10) Now boot sysB and configure a zone with the parameters shown above in Step 1. (Again, the safest method is to use "zonecfg ... export" on sysA as described in section "Method Overview" above.) The one difference is the name of the rootzpool storage device, which was shown in the list of assumptions, and which you must determine by booting sysB and using the "format" or "zpool import" command. When that is done, you should see the output shown next. (I used the same zonename - "zone1" - in this example, but you can choose any valid zonename you want.) root@sysB:~# zoneadm list -cv ID NAME STATUS PATH BRAND IP 0 global running / solaris shared - zone1 configured /zones/zone1 solaris excl root@sysB:~# zonecfg -z zone1 info zonename: zone1 zonepath: /zones/zone1 brand: solaris autoboot: false bootargs: file-mac-profile: pool: limitpriv: scheduling-class: ip-type: exclusive hostid: fs-allowed: anet: linkname: net0 ... rootzpool: storage: dev:dsk/c7t3d0 Step 11) Attaching the zone automatically imports the zpool. root@sysB:~# zoneadm -z zone1 attach Imported zone zpool: zone1_rpool Progress being logged to /var/log/zones/zoneadm.20121022T184034Z.zone1.attach Installing: Using existing zone boot environment Zone BE root dataset: zone1_rpool/rpool/ROOT/solaris Cache: Using /var/pkg/publisher. Updating non-global zone: Linking to image /. Processing linked: 1/1 done Updating non-global zone: Auditing packages. No updates necessary for this image. Updating non-global zone: Zone updated. Result: Attach Succeeded. Log saved in non-global zone as /zones/zone1/root/var/log/zones/zoneadm.20121022T184034Z.zone1.attach root@sysB:~# zoneadm -z zone1 boot root@sysB:~# zlogin zone1 [Connected to zone 'zone1' pts/2] Oracle Corporation SunOS 5.11 11.1 September 2012 Step 12) Now let's migrate the zone back to sysA. Create a file in zone1 so we can verify it exists after we migrate the zone back, then begin migrating it back. root@zone1:~# ls /opt root@zone1:~# touch /opt/fileA root@zone1:~# ls -l /opt/fileA -rw-r--r-- 1 root root 0 Oct 22 14:47 /opt/fileA root@zone1:~# exit logout [Connection to zone 'zone1' pts/2 closed] root@sysB:~# zoneadm -z zone1 shutdown root@sysB:~# zoneadm -z zone1 detach Exported zone zpool: zone1_rpool root@sysB:~# init 0 Step 13) Back on sysA, check the status. Oracle Corporation SunOS 5.11 11.1 September 2012 root@sysA:~# zoneadm list -cv ID NAME STATUS PATH BRAND IP 0 global running / solaris shared - zone1 configured /zones/zone1 solaris excl root@sysA:~# zpool list NAME SIZE ALLOC FREE CAP DEDUP HEALTH ALTROOT rpool 17.6G 11.2G 6.47G 63% 1.00x ONLINE - Step 14) Re-attach the zone back to sysA. root@sysA:~# zoneadm -z zone1 attach Imported zone zpool: zone1_rpool Progress being logged to /var/log/zones/zoneadm.20121022T190441Z.zone1.attach Installing: Using existing zone boot environment Zone BE root dataset: zone1_rpool/rpool/ROOT/solaris Cache: Using /var/pkg/publisher. Updating non-global zone: Linking to image /. Processing linked: 1/1 done Updating non-global zone: Auditing packages. No updates necessary for this image. Updating non-global zone: Zone updated. Result: Attach Succeeded. Log saved in non-global zone as /zones/zone1/root/var/log/zones/zoneadm.20121022T190441Z.zone1.attach root@sysA:~# zpool list NAME SIZE ALLOC FREE CAP DEDUP HEALTH ALTROOT rpool 17.6G 11.2G 6.47G 63% 1.00x ONLINE - zone1_rpool 1.98G 491M 1.51G 24% 1.00x ONLINE - root@sysA:~# zoneadm -z zone1 boot root@sysA:~# zlogin zone1 [Connected to zone 'zone1' pts/2] Oracle Corporation SunOS 5.11 11.1 September 2012 root@zone1:~# zpool list NAME SIZE ALLOC FREE CAP DEDUP HEALTH ALTROOT rpool 1.98G 538M 1.46G 26% 1.00x ONLINE - Step 15) Check for the file created on sysB, earlier. root@zone1:~# ls -l /opt total 1 -rw-r--r-- 1 root root 0 Oct 22 14:47 fileA Next Steps Here is a brief list of some of the fun things you can try next. Add space to the zone by adding a second storage device to the rootzpool. Make sure that you add it to the configurations of both zones! Create a new zone, specifying two disks in the rootzpool when you first configure the zone. When you install that zone, or clone it from another zone, zoneadm uses those two disks to create a mirrored pool. (Three disks will result in a three-way mirror, etc.) Conclusion Hopefully you have seen the ease with which you can now move Solaris Zones from one system to another.

  Read the article

• Developing an Implementation Plan with Iterations by Russ Pitts

  - by user535886

  Developing an Implementation Plan with Iterations by Russ Pitts  Ok, so you have come to grips with understanding that applying the iterative concept, as defined by OUM is simply breaking up the project effort you have estimated for each phase into one or more six week calendar duration blocks of work. Idea being the business user(s) or key recipient(s) of work product(s) being developed never go longer than six weeks without having some sort of review or prototyping of the work results for an iteration…”think-a-little”, “do-a-little”, and “show-a-little” in a six week or less timeframe…ideally the business user(s) or key recipients(s) are involved throughout. You also understand the OUM concept that you only plan for that which you have knowledge of. The concept further defined, a project plan initially is developed at a high-level, and becomes more detailed as project knowledge grows. Agreeing to this concept means you also have to admit to the fallacy that one can plan with precision beyond six weeks into a project…Anything beyond six weeks is a best guess in most cases when dealing with software implementation projects. Project planning, as defined by OUM begins with the Implementation Plan view, which is a very high-level perspective of the effort estimated for each of the five OUM phases, as well as the number of iterations within each phase. You might wonder how can you predict the number of iterations for each phase at this early point in the project. Remember project planning is not an exact science, and initially is high-level and abstract in nature, and then becomes more detailed and precise as the project proceeds. So where do you start in defining iterations for each phase for a project? The following are three easy steps to initially define the number of iterations for each phase: Step 1 => Start with identifying the known factors… …Prior to starting a project you should know: · The agreed upon time-period for an iteration (e.g 6 weeks, or 4 weeks, or…) within a phase (recommend keeping iteration time-period consistent within a phase, if not for the entire project) · The number of resources available for the project · The number of total number of man-day (effort) you have estimated for each of the five OUM phases of the project · The number of work days for a week Step 2 => Calculate the man-days of effort required for an iteration within a phase… Lets assume for the sake of this example there are 10 project resources, and you have estimated 2,536 man-days of work effort which will need to occur for the elaboration phase of the project. Let’s also assume a week for this project is defined as 5 business days, and that each iteration in the elaboration phase will last a calendar duration of 6 weeks. A simple calculation is performed to calculate the daily burn rate for a single iteration, which produces a result of… ((Number of resources * days per week) * duration of iteration) = Number of days required per iteration ((10 resources * 5 days/week) * 6 weeks) = 300 man days of effort required per iteration Step 3 => Calculate the number of iterations that can occur within a phase Next calculate the number of iterations that can occur for the amount of man-days of effort estimated for the phase being considered… (number of man-days of effort estimated / number of man-days required per iteration) = # of iterations for phase (2,536 man-days of estimated effort for phase / 300 man days of effort required per iteration) = 8.45 iterations, which should be rounded to a whole number such as 9 iterations* *Note - It is important to note this is an approximate calculation, not an exact science. This particular example is a simple one, which assumes all resources are utilized throughout the phase, including tech resources, etc. (rounding down or up to a whole number based on project factor considerations). It is also best in many cases to round up to higher number, as this provides some calendar scheduling contingency.

  Read the article

• UFW as an active service on Ubuntu

  - by lamcro

  Every time I restart my computer, and check the status of the UFW firewall (sudo ufw status), it is disabled, even if I then enable and restart it. I tried putting sudo ufw enable as one of the startup applications but it asks for the sudo password every time I log on, and I'm guessing it does not protect anyone else who logs on my computer. How can I setup ufw so it is activated when I turn on my computer, and protects all accounts? Update I just tried /etc/init.d/ufw start, and it activated the firewall. Then I restarted the computer, and again it was disabled. content of /etc/ufw/ufw.conf # /etc/ufw/ufw.conf # # set to yes to start on boot ENABLED=yes # set to one of 'off', 'low', 'medium', 'high' LOGLEVEL=full content of /etc/default/ufw # /etc/default/ufw # # Set to yes to apply rules to support IPv6 (no means only IPv6 on loopback # accepted). You will need to 'disable' and then 'enable' the firewall for # the changes to take affect. IPV6=no # Set the default input policy to ACCEPT, ACCEPT_NO_TRACK, DROP, or REJECT. # ACCEPT enables connection tracking for NEW inbound packets on the INPUT # chain, whereas ACCEPT_NO_TRACK does not use connection tracking. Please note # that if you change this you will most likely want to adjust your rules. DEFAULT_INPUT_POLICY="DROP" # Set the default output policy to ACCEPT, ACCEPT_NO_TRACK, DROP, or REJECT. # ACCEPT enables connection tracking for NEW outbound packets on the OUTPUT # chain, whereas ACCEPT_NO_TRACK does not use connection tracking. Please note # that if you change this you will most likely want to adjust your rules. DEFAULT_OUTPUT_POLICY="ACCEPT" # Set the default forward policy to ACCEPT, DROP or REJECT. Please note that # if you change this you will most likely want to adjust your rules DEFAULT_FORWARD_POLICY="DROP" # Set the default application policy to ACCEPT, DROP, REJECT or SKIP. Please # note that setting this to ACCEPT may be a security risk. See 'man ufw' for # details DEFAULT_APPLICATION_POLICY="SKIP" # By default, ufw only touches its own chains. Set this to 'yes' to have ufw # manage the built-in chains too. Warning: setting this to 'yes' will break # non-ufw managed firewall rules MANAGE_BUILTINS=no # # IPT backend # # only enable if using iptables backend IPT_SYSCTL=/etc/ufw/sysctl.conf # extra connection tracking modules to load IPT_MODULES="nf_conntrack_ftp nf_nat_ftp nf_conntrack_irc nf_nat_irc" Update Followed your advise and ran update-rc.d with no luck. lester@mcgrath-pc:~$ sudo update-rc.d ufw defaults update-rc.d: warning: /etc/init.d/ufw missing LSB information update-rc.d: see <http://wiki.debian.org/LSBInitScripts> Adding system startup for /etc/init.d/ufw ... /etc/rc0.d/K20ufw -> ../init.d/ufw /etc/rc1.d/K20ufw -> ../init.d/ufw /etc/rc6.d/K20ufw -> ../init.d/ufw /etc/rc2.d/S20ufw -> ../init.d/ufw /etc/rc3.d/S20ufw -> ../init.d/ufw /etc/rc4.d/S20ufw -> ../init.d/ufw /etc/rc5.d/S20ufw -> ../init.d/ufw lester@mcgrath-pc:~$ ls -l /etc/rc?.d/*ufw lrwxrwxrwx 1 root root 13 2009-12-20 20:34 /etc/rc0.d/K20ufw -> ../init.d/ufw lrwxrwxrwx 1 root root 13 2009-12-20 20:34 /etc/rc1.d/K20ufw -> ../init.d/ufw lrwxrwxrwx 1 root root 13 2009-12-20 20:34 /etc/rc2.d/S20ufw -> ../init.d/ufw lrwxrwxrwx 1 root root 13 2009-12-20 20:34 /etc/rc3.d/S20ufw -> ../init.d/ufw lrwxrwxrwx 1 root root 13 2009-12-20 20:34 /etc/rc4.d/S20ufw -> ../init.d/ufw lrwxrwxrwx 1 root root 13 2009-12-20 20:34 /etc/rc5.d/S20ufw -> ../init.d/ufw lrwxrwxrwx 1 root root 13 2009-12-20 20:34 /etc/rc6.d/K20ufw -> ../init.d/ufw

  Read the article

• Tuning performance of Ubuntu 10.04 on Compaq Evo W4000.

  - by Fantomas

  Hi, I got this computer free and installed Ubuntu 10.04 on it + updates, plus followed the following tutorial all the way: http://www.unixmen.com/linux-tutorials/937-things-to-do-after-installing-ubuntu-1004-lts-lucid-lynx I love the Docky which comes with it, but the computer has been running rather slowly. The System: kernel 2.6.32-22-generic Gnome 2.30.0 (I like Gnome!) Memory: 1GB Processor: Intel (R) Pentium (R) 4 CPU 1700 MHz (needless to say, it is 32 bit). I think I dedicated 128 Mb to video memory while installing, but cannot find this setting now. I did also install an NVidia driver for the 3D card, so I probably want to reclaim that memory back. I want to trim the fat but I also want to keep some of the sex appeal of Ubuntu 10.04. I will gift this computer to a friend, who will use it for Internet, music, videos, word processing, Skype and instant messaging - he is non-technical, so this hardware and Linux should work for him; I just need to speed it up while keeping the good software and having a nice UI. I sort of know my way around Linux, but not that well. Feel free to ask me to run particular commands if you want more info. For starters, here are the services below. Which ones can I kill and how? What else can go? There is no need to run ssh or ftp or http or ntp servers. As I said before, this computer is for non-technical person. There is also absolutely no bluetooth or wireless networking needed - it will feed off a regular ethernet cable. What I do not want to do is reinstall some other distro or recompile a kernel. I want to make it 80% perfect spending 20% of the energy :) Thanks! $ service --status-all [ ? ] acpi-support [ ? ] acpid [ ? ] alsa-mixer-save [ ? ] anacron [ - ] apparmor [ ? ] apport [ ? ] atd [ ? ] avahi-daemon [ ? ] binfmt-support [ - ] bluetooth [ - ] bootlogd [ - ] brltty [ ? ] console-setup [ ? ] cron [ + ] cups [ ? ] dbus [ ? ] dmesg [ ? ] dns-clean [ ? ] failsafe-x [ - ] fancontrol [ ? ] gdm [ - ] grub-common [ ? ] hostname [ ? ] hwclock [ ? ] hwclock-save [ ? ] irqbalance [ - ] kerneloops [ ? ] killprocs [ - ] lm-sensors [ ? ] module-init-tools [ ? ] network-interface [ ? ] network-interface-security [ ? ] network-manager [ ? ] networking [ ? ] ondemand [ ? ] pcmciautils [ ? ] plymouth [ ? ] plymouth-log [ ? ] plymouth-splash [ ? ] plymouth-stop [ ? ] pppd-dns [ ? ] procps [ + ] pulseaudio [ ? ] rc.local [ - ] rsync [ ? ] rsyslog [ - ] saned [ ? ] screen-cleanup [ ? ] sendsigs [ ? ] speech-dispatcher [ ? ] stop-bootlogd [ ? ] stop-bootlogd-single [ ? ] udev [ ? ] udev-finish [ ? ] udevmonitor [ ? ] udevtrigger [ ? ] ufw [ ? ] umountfs [ ? ] umountnfs.sh [ ? ] umountroot [ ? ] unattended-upgrades [ - ] urandom [ + ] winbind [ ? ] wpa-ifupdown [ - ] x11-common

  Read the article

• Is a university education really worth it for a good programmer?

  - by Jon Purdy

  The title says it all, but here's the personal side of it: I've been doing design and programming for about as long as I can remember. If there's a programming problem, I can figure it out. (Though admittedly StackOverflow has allowed me to skip the figuring out and get straight to the doing in many instances.) I've made games, esoteric programming languages, and widgets and gizmos galore. I'm currently working on a general-purpose programming language. There's nothing I do better than programming. However, I'm just as passionate about design. Thus when I felt leaving high school that my design skills were lacking, I decided to attend university for New Media Design and Imaging, a digital design-related major. For a year, I diligently studied art and programmed in my free time. As the next year progressed, however, I was obligated to take fewer art and design classes and more technical classes. The trouble was of course that these classes were geared toward non-technical students, and were far beneath my skill level at the time. No amount of petitioning could overcome the institution's reluctance to allow me to test out of such classes, and the major offered no promise for any greater challenge in the future, so I took the extreme route: I switched into the technical equivalent of the major, New Media Interactive Development. A lot of my credits moved over into the new major, but many didn't. It would have been infeasible to switch to a more rigorous technical major such as Computer Science, and having tutored Computer Science students at every level here, I doubt I would be exposed to anything that I haven't already or won't eventually find out on my own, since I'm so involved in the field. I'm now on track to graduate perhaps a year later than I had planned, which puts a significant financial strain on my family and my future self. My schedule continues to be bogged down with classes that are wholly unnecessary for me to take. I'm being re-introduced to subjects that I've covered a thousand times over, simply because I've always been interested in it all. And though I succeed in avoiding the cynical and immature tactic of failing to complete work out of some undeserved sense of superiority, I'm becoming increasingly disillusioned by the lack of intellectual stimulation. Further, my school requires students to complete a number of quarters of co-op work experience proportional to their major. My original major required two quarters, but my current requires three, delaying my graduation even more. To top it all off, college is putting a severe strain on my relationship with my very close partner of a few years, so I've searched diligently for co-op jobs in my area, alas to no avail. I'm now in my third year, and approaching that point past which I can no longer handle this. Either I keep my head down, get a degree no matter what it takes, and try to get a job with a company that will pay me enough to do what I love that I can eventually pay off my loans; or I cut my losses now, move wherever there is work, and in six months start paying off what debt I've accumulated thus far. So the real question is: is a university education really more than just a formality? It's a big decision, and one I can't make lightly. I think this is the appropriate venue for this kind of question, and I hope it sticks around for the sake of others who might someday find themselves in similar situations. My heartfelt thanks for reading, and in advance for your help.

  Read the article

• PC runs very slowly for no apparent reason

  - by GalacticCowboy

  I have a Dell Latitude D820 that I've owned for about 2.5 years. It is a Core 2 Duo T7200 2.0GHz, with 2 GB of RAM, an 80 GB hard drive and an NVidia Quadro 120M video card. The computer was purchased in late November of 2006 with XP Pro, and included a free upgrade to Vista Business. (Vista was available on MSDN but not yet via retail, so the Vista Business upgrades weren't shipped until March of '07.) Since we had an MSDN subscription at the time, I installed Vista Ultimate on it pretty much as soon as I got it. It ran happily until sometime in the spring of 2007 when Media Center (which I had never used except to watch DVDs) started throwing some kind of bizarre SQL (CE?) error. This error would pop up at random times just while using the computer. Furthermore, Media Center would no longer start. I never identified the cause of this error. I had the Vista Business upgrade by this time, so I nuked the machine, installed XP and all the drivers, and then the Vista Business upgrade. Again, it ran happily for a few months and then started behaving badly once again. Vista Business doesn't have Media Center, so this exhibited completely unrelated symptoms. For no apparent reason and at fairly random times, the machine would suddenly appear to freeze up or run very slowly. For example, launching a new application window (any app) might take 30-45 seconds to paint fully. However, Task Manager showed very low CPU load, memory, etc. I tried all the normal stuff (chkdsk, defrag, etc.) and ran several diagnostic programs to try to identify any problems, but none found anything. It eventually reached the point that the computer was all but unusable, so I nuked it again and installed XP. This time I decided to stick with XP instead of going to Vista. However, within the past couple of months it has started to exhibit the same symptoms in XP that I used to see in Vista. The computer is still under Dell warranty until December, but so far they aren't any help unless I can identify a specific problem. A friend (partner in a now-dead business) has an identical machine that was purchased at the same time. His machine exhibits none of these symptoms, which leads me to believe it is a hardware issue, but I can't figure out how to identify it. Any ideas? Utilities? Seen something similar? At this point I can't even identify any pattern to the behavior, but would be willing to run a "stress test"-style app for as long as a couple days if I had any hope that it would find something. EDIT July 17 I'm testing jerryjvl's answer regarding the video card, though I'm not sure it fully explains the symptoms yet. This morning I ran a video stress test. The test itself ran fine, but immediately afterward the PC started acting up again. I left ProcExp open and various system processes were consuming 50-60% of the CPU but with no apparent reason. For example, "services.exe" was eating about 40%, but the sum of its child processes wasn't higher than about 5%. I left it alone for several minutes to settle down, and then it was fine again. I used the "video card stability test" from firestone-group.com. Its output isn't very detailed, but it at least exercises the hardware pretty hard. EDIT July 22 Thanks for your excellent suggestions. Here is an update on what I have tried so far. Ran memtest86, SeaTools (Seagate), Hitachi drive fitness test, video card stability test (mentioned above). The video card test was the only one that seemed to produce any results, though it didn't occur during the actual test. I defragged the drive (again...) with JkDefrag I dropped the video card

  Read the article

• Fun with Python

  - by dotneteer

  I am taking a class on Coursera recently. My formal education is in physics. Although I have been working as a developer for over 18 years and have learnt a lot of programming on the job, I still would like to gain some systematic knowledge in computer science. Coursera courses taught by Standard professors provided me a wonderful chance. The three languages recommended for assignments are Java, C and Python. I am fluent in Java and have done some projects using C++/MFC/ATL in the past, but I would like to try something different this time. I first started with pure C. Soon I discover that I have to write a lot of code outside the question that I try to solve because the very limited C standard library. For example, to read a list of values from a file, I have to read characters by characters until I hit a delimiter. If I need a list that can grow, I have to create a data structure myself, something that I have taking for granted in .Net or Java. Out of frustration, I switched to Python. I was pleasantly surprised to find that Python is very easy to learn. The tutorial on the official Python site has the exactly the right pace for me, someone with experience in another programming. After a couple of hours on the tutorial and a few more minutes of toying with IDEL, I was in business. I like the “battery supplied” philosophy that gives everything that I need out of box. For someone from C# or Java background, curly braces are replaced by colon(:) and tab spaces. Although I tend to miss colon from time to time, I found that the idea of tab space is actually very nice once I get use to them. I also like to feature of multiple assignment and multiple return parameters. When I need to return a by-product, I just add it to the list of returns. When would use Python? I would use Python if I need to computer anything quick. The language is very easy to use. Python has a good collection of libraries (packages). The REPL of the interpreter allows me test ideas quickly before committing them into script. Lots of computer science work have been ported from Lisp to Python. Some universities are even teaching SICP in Python. When wouldn’t I use Python? I mostly would not use it in a managed environment, such as Ironpython or Jython. Both .Net and Java already have a rich library so one has to make a choice which library to use. If we use the managed runtime library, the code will tie to the particular runtime and thus not portable. If we use the Python library, then we will face the relatively long start-up time. For this reason, I would not recommend to use Ironpython for WP7 development. The only situation that I see merit with managed Python is in a server application where I can preload Python so that the start-up time is not a concern. Using Python as a managed glue language is an over-kill most of the time. A managed Scheme could be a better glue language as it is small enough to start-up very fast.

  Read the article

• Windows Service SearchIndexer.exe Crashes on Indexing

  - by Josh Jay

  Relevant Specs: Windows 7 Professional 64-bit SP1 Outlook 2010 Version 14.0.7116.5000 (32-bit) Original Symptom: In outlook, I attempted to search for an email but nothing ever returned and the indicator kept going like it was searching. Attempted Resolutions: I investigated the search options and with some research noticed the Windows Service "Windows Search" (SearchIndexer.exe) was not running. I attempted to start it but I receive this error message: "Windows could not start the Windows Search service on Local Computer. Error 1067: The process terminated unexpectedly." The Event Viewer gives this error entry: Log Name: Application Source: Application Error Date: 6/3/2014 11:02:05 AM Event ID: 1000 Task Category: (100) Level: Error Keywords: Classic User: N/A Computer: ***REMOVED FOR POST*** Description: Faulting application name: SearchIndexer.exe, version: 7.0.7601.17610, time stamp: 0x4dc0d019 Faulting module name: KERNELBASE.dll, version: 6.1.7601.18229, time stamp: 0x51fb1677 Exception code: 0xc0000005 Fault offset: 0x000000000000940d Faulting process id: 0x6a0 Faulting application start time: 0x01cf7f3cc83757c6 Faulting application path: C:\Windows\system32\SearchIndexer.exe Faulting module path: C:\Windows\system32\KERNELBASE.dll Report Id: 06424160-eb30-11e3-9555-843a4b07b336 Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Application Error" /> <EventID Qualifiers="0">1000</EventID> <Level>2</Level> <Task>100</Task> <Keywords>0x80000000000000</Keywords> <TimeCreated SystemTime="2014-06-03T15:02:05.000000000Z" /> <EventRecordID>602923</EventRecordID> <Channel>Application</Channel> <Computer>M6700-12011.ncaa.org</Computer> <Security /> </System> <EventData> <Data>SearchIndexer.exe</Data> <Data>7.0.7601.17610</Data> <Data>4dc0d019</Data> <Data>KERNELBASE.dll</Data> <Data>6.1.7601.18229</Data> <Data>51fb1677</Data> <Data>c0000005</Data> <Data>000000000000940d</Data> <Data>6a0</Data> <Data>01cf7f3cc83757c6</Data> <Data>C:\Windows\system32\SearchIndexer.exe</Data> <Data>C:\Windows\system32\KERNELBASE.dll</Data> <Data>06424160-eb30-11e3-9555-843a4b07b336</Data> </EventData> </Event> The regular windows search (from start menu) works fine, and if I reboot the machine the service starts up OK but as soon as it kicks off when I let the machine idle for long enough it crashes (same Event Viewer entry). We also tried the Microsoft Utility to no avail. Has anyone seen this issue before?

  Read the article

• Where to download replacement "Explorerframe.DLL" Files for x64 Windows 7 Pro?

  - by Ben Franchuk

  After posting this question, I did some research to reveal what the problem likely was, and found what I need to fix. Following this is the original post, then my updated question. A few months ago I ended up requiring to change my computer's SID to fix a problem it had been having- Instead of fixing the problem, though, it screwed up my at-the-time current install of windows, to the point of me needing to do a fresh install. As I am in possession of an OEM copy of Windows 7 Pro 64 Bit, I successfully reinstalled over the dead copy with that (all the files that were on the computer previous to this windows install were put in a Windows.old folder). Everything installed and worked absolutely fine, except for one thing. The problem I am experiencing is that, in some Windows Explorer windows, the explorer pane doesn't show. Instead, it simply shows a white area where the pane would show. This makes some software not usable, I recently realized; Software such as Cubase, which use just the explorer pane to select file save locations, cannot save at all as the pane itself is... not operational. Below is a screenshot of this problem as it occurs in cubase; ...and again as it shows in UTorrent in the save location selector window. The highlighted area is where the sidebar would NORMALLY be. Pardon my scribbling over some of the things in the window- I would personally rather the internet did not get a glimpse of my files. I have yet to find a common reason why the pane works in some applications when they pull explorer, and others not. I have yet to see it go away, and the software affected by it has been affected since I reinstalled my copy of windows. Initially, I was able to live with it as I can type out save locations in the file name bar to navigate, but with software like Cubase, I do not have this option. Reinstalling windows again is NOT an option. Here's the updated question. After posting this question originally, I did some research on the problem in question, and it turns out that this is extremely easily fixable via replacing the file "ExplorerFrame.DLL" which is located in the System32 and SystemWOW64 Folders, in the windows folder, on the C:\ drive. As I quite frequently customize my computer, this is a normal thing for me to do and I know exactly how to safely and properly replace this file. The only problem is that I cannot for the life of me find a download of this file that actually works with my computer. I tried a couple from some different sites but they all caused explorer to not restart (I was given an error when starting the application from Task Manager) and was forced to revert to the broken .DLL files. Since there are 2 separate "ExplorerFrame.DLL" files; one for 64 bit and the other for 32 bit, I am assuming that I will need to download 2 separate versions to replace the corrupted ones. Where can I acquire these files? I am currently running Windows 7 Professional x64 Bit.

  Read the article

• What *exactly* gets screwed when I kill -9 or pull the power?

  - by Mike

  Set-Up I've been a programmer for quite some time now but I'm still a bit fuzzy on deep, internal stuff. Now. I am well aware that it's not a good idea to either: kill -9 a process (bad) spontaneously pull the power plug on a running computer or server (worse) However, sometimes you just plain have to. Sometimes a process just won't respond no matter what you do, and sometimes a computer just won't respond, no matter what you do. Let's assume a system running Apache 2, MySQL 5, PHP 5, and Python 2.6.5 through mod_wsgi. Note: I'm most interested about Mac OS X here, but an answer that pertains to any UNIX system would help me out. My Concern Each time I have to do either one of these, especially the second, I'm very worried for a period of time that something has been broken. Some file somewhere could be corrupt -- who knows which file? There are over 1,000,000 files on the computer. I'm often using OS X, so I'll run a "Verify Disk" operation through the Disk Utility. It will report no problems, but I'm still concerned about this. What if some configuration file somewhere got screwed up. Or even worse, what if a binary file somewhere is corrupt. Or a script file somewhere is corrupt now. What if some hardware is damaged? What if I don't find out about it until next month, in a critical scenario, when the corruption or damage causes a catastrophe? Or, what if valuable data is already lost? My Hope My hope is that these concerns and worries are unfounded. After all, after doing this many times before, nothing truly bad has happened yet. The worst is I've had to repair some MySQL tables, but I don't seem to have lost any data. But, if my worries are not unfounded, and real damage could happen in either situation 1 or 2, then my hope is that there is a way to detect it and prevent against it. My Question(s) Could this be because modern operating systems are designed to ensure that nothing is lost in these scenarios? Could this be because modern software is designed to ensure that nothing lost? What about modern hardware design? What measures are in place when you pull the power plug? My question is, for both of these scenarios, what exactly can go wrong, and what steps should be taken to fix it? I'm under the impression that one thing that can go wrong is some programs might not have flushed their data to the disk, so any highly recent data that was supposed to be written to the disk (say, a few seconds before the power pull) might be lost. But what about beyond that? And can this very issue of 5-second data loss screw up a system? What about corruption of random files hiding somewhere in the huge forest of files on my hard drives? What about hardware damage? What Would Help Me Most Detailed descriptions about what goes on internally when you either kill -9 a process or pull the power on the whole system. (it seems instant, but can someone slow it down for me?) Explanations of all things that could go wrong in these scenarios, along with (rough of course) probabilities (i.e., this is very unlikely, but this is likely)... Descriptions of measures in place in modern hardware, operating systems, and software, to prevent damage or corruption when these scenarios occur. (to comfort me) Instructions for what to do after a kill -9 or a power pull, beyond "verifying the disk", in order to truly make sure nothing is corrupt or damaged somewhere on the drive. Measures that can be taken to fortify a computer setup so that if something has to be killed or the power has to be pulled, any potential damage is mitigated. Thanks so much!

  Read the article

• Windows 7, file properties - Is "date accessed" ALWAYS 100% accurate?

  - by Robert

  Hello, Here's the situation: I went on vacation for a couple of weeks, but before I left, I took the harddrive out of my computer and hid it in a different location. Upon coming back on Monday and putting the harddrive back in my computer, I right-clicked on different files to see their properties. Interestingly enough, several files had been accessed during the time I was gone! I right-clicked different files in various locations on the harddrive, and all of these suspect files had been accessed within a certain time range (Sunday, ?January ?09, ?2011, approximately ??between 6:52:16 PM - 7:16:25 PM). Some of them had been accessed at the exact same time--down to the very second. This makes me think that someone must have done a search on my harddrive for certain types of files and then copied all those files to some other medium. The Windows 7 installation on this harddrive is password protected, but NOT encrypted, so they could have easily put the harddrive into an enclosure/toaster to access it from a different computer. Of course I did not right-click every single file on my computer, but did so in different folders. For instance, one of the folders I went through has different types of files: .mp3, ,prproj, .3gp, .mpg, .wmv, .xmp, .txt with file-sizes ranging from 2 KB to 29.7 MB (there is also a sub-folder in this folder which contains only .jpg files); however, of all these different types of files in this folder and its subfolder, all of them had been accessed (including the .jpg files from the sub-folder) EXCEPT the .mp3 files (if it makes any difference, the .mp3 files in this folder range in size from 187 KB to 4881 KB). Additionally, this sub-folder which contained only .jpg files (48 .jpg files to be exact) was not accessed during this time--only the .jpg files within it were accessed-- (between 6:57:03 PM - 6:57:08 PM). I thought that perhaps this was some kind of Windows glitch that was displaying the wrong access date, but then I looked at the "date created" and "date modified" for all of these files in question, and their created/modified dates and times were spot on correct. My first thought was that someone put the harddrive into an enclosure/toaster and viewed the files; but then I realized that this was impossible because several of the files had been accessed at the same exact time down to the second. So this made me think that the only other way the "date accessed" could have changed would have been if someone copied the files. Is there any chance at all whatsoever that this is some kind of Windows glitch or something, or is it a fact that someone was indeed accessing my files (and if someone was accessing my files, am I right about the files in question having been copied)? Is there any other possibility for what could have happened? Do I need to use any kinds of forensics tools to further investigate this matter (and if so, which tools), or is there any other way in which I can be certain of what took place in that timeframe the day before I got back? Or is what I see with Windows 7 good enough (i.e. accurate and truthful)? Thanks in advance, and please let me know if any other details are required on my part.

  Read the article

• Automatically support new changes with Python.

  - by Zachary Brown

  I was working on a program,that I need to support new additions. Hmmm. Let me give you some background on the program. It is an educational software program that has quizzes for the user to take, just to gain odd knowledge. Now, It currently supports 6 subjects, all organized with directores on the HDD ( i.e. the Science directory is called science. ) and the way you launch the subject to see what quizzes you have to take is by pushing a button on the home screen. This sort of thing prevents easy subject additions. I want to be able to add a subject later on without having to recode the home screen and re organize all the buttons. I would use a Listbox and os.listdir(...), but I was kind of wanting something prettier than a Listbox. I am using Tkinter on Windows. The Python version I am using is 2.6 Is there a "fancy" listbox sort of thing that can be styled to work with the background?

  Read the article

• Have any software engineers gotten math degrees later in their careers?

  - by vin

  I have a bachelors in computer science and worked the last 12 years as a software engineer. I'm bored with doing general development work, so I want to specialize. I'm thinking about getting a master's degree in math so I can build math models and write algorithms to implement them. I'm unsure what type of work I'd do (financial, gaming, graphics, science, research, etc) but I'm open minded. I would need to refresh my undergrad math skills (which are old and faded), but I loved algebra and calculus. I've been working with couple statisticians so I've been finding myself more interested in statistics. Since I'm a parent supporting a household, I would have to continue working while studying. Have any software engineers taken this route? (Specifically, going from BS in comp sci to MS in math.) If so, what advice do you have for coursework, financing, and getting a job that combines programming with advanced math? How abundant are these kinds of jobs? I'm not sure where one starts. Also, how do you hop from a BS to an MS in a different subject?

  Read the article

• looking to streamline my RSS feed mashup

  - by Mark Cejas

  Hello crafty developers, I have aggregated RSS feeds from various sources with RSSowl, fetching directly from the social mention API. The RSS feeds are categorized into the following major categories: blogs, news, twitter, Q&A and social networking sites. Each major category is nested with a common group of RSS feeds that represent a particular client/brand ontology. Merging these feeds into the RSSowl reader application, allows me to conduct and save refined search queries (from the aggregated data) into a single file - that I can then tag and further segment for analysis. This scheme is utilized for my own research needs and has helped me considerably. However, I find this RSS mashup scheme kinda clumsy, it requires quite a bit of time to initially organize all of the feeds and I would like to be able to do further natural language processing to the data as well as eventually be able to rank the collected list of URL's into some order of media prominence - right I don't want to pay the ridiculous radian6 web analytics fees, when my intuition is telling me that with a bit of 'elbow grease' I can maybe leverage some available resources online to develop a functional low scale web mining application and get some good intelligence from it. I am now starting to learn a little about computer science - my background is in physical science/statistics so is my thinking in the right track? So, I guess I am imagining an application that allows me to query in a refined manner. A manner that allows me to search for keyword combinations, applying AND/OR operators, selectively focus my queries into particular sources - like a collection of blogs or twitter, or social networking communities, then save the results of my queries into a structured format that can then be manipulated and explored. Am I dreaming? I just had to get all of this out. any bit of advice and insight would be hugely appreciated. my best, Mark

  Read the article

• Send html array as post variable using Request.JSON

  - by ian

  I have an html: First name: <input type='text' name='first_name' value='' /><br/> Last name: <input type='text' name='last_name' value='' /><br/> <input type='checkbox' name='category[]' value='Math' /> Math<br/> <input type='checkbox' name='category[]' value='Science' /> Science<br/> <input type='checkbox' name='category[]' value='History' /> History<br/> etc..... I want to send(using post method) the selected categories(category[]) via mootools ajax so that if I dump the $_POST variable in the server I will get something like: array(1) { [category]=> array(2) { [0]=> string(4) "Math" [1]=> string(7) "History" } } What should be the javascript(mootools) code for it? Below is my partial code. new Request.JSON({url: '/ajax_url', onSuccess: function(){ alert('success'); } }).post(???); Note that I don't want to send first_name and last_name fields. I only want to send the category field which is an html array.

  Read the article

• Dynamic editor upload into web page. Need advice

  - by Andrew Florko

  Hello everybody, I am writing intranet site for tracking employees science activities in organization. There lots of editable information on each personal page (science degree, publications & so on) so I upload editor per request (user clicks "edit" and modal dialog with html editor: set of textboxes/comboboxes/autocomplete features & validation logic appears). Editor is html layout that is wrapped with jquery dialog plugin + some logic, written as javascript functions that should be invoked from the callee page (onsubmit, validate, afterLoad editor events). There are also attributes (editor preferrable with and height) that are passed to callee page also. Currently I send these functions & attribute as ... function onsubmit() { }; function validate() { } var width = 640; var height = 800 ... code that is embedded into the request page. Function calls and editor markup wrap with jquery plugin completed in the callee page. It works, but I have some try { call editor event handler } catch { } stuff in callee page (because not every editor provides these functions) and some attributes (editor width & height for instance) that are loaded as variables declared in javascript. Please, suggest, is there a better approach to build & use custom editors for my situation. Thank you in advance!

  Read the article

• How to call a method in another class using the arraylist index in java?

  - by Puchatek

  Currently I have two classes. A Classroom class and a School class. public void addTeacherToClassRoom(Classroom myClassRoom, String TeacherName) I would like my method addTeacherToClassRoom to use the Classroom Arraylist index number to setTeacherName e.g. int 0 = maths int 1 = science I would like to setTeacherName "Daniel" in int 1 science. many, thanks public class Classroom { private String classRoomName; private String teacherName; public void setClassRoomName(String newClassRoomName) { classRoomName = newClassRoomName; } public String returnClassRoomName() { return classRoomName; } public void setTeacherName(String newTeacherName) { teacherName = newTeacherName; } public String returnTeacherName() { return teacherName; } } import java.util.ArrayList; public class School { private ArrayList<Classroom> classrooms; private String classRoomName; private String teacherName; public School() { classrooms = new ArrayList<Classroom>(); } public void addClassRoom(Classroom newClassRoom, String theClassRoomName) { classrooms.add(newClassRoom); classRoomName = theClassRoomName; } public void addTeacherToClassRoom(Classroom myClassRoom, String TeacherName) { myClassRoom.setTeacherName(TeacherName); } }

  Read the article

• What kind of “sysadmin stuff” should I show to students during a talk?

  - by Gregory Eric Sanderaon

  A teacher asked me If I could talk about my job as a linux sysadmin in his class. The course is called "Introduction to Operating systems" and i've been given 45 minutes to talk. The students are beginning their second year, so they've had a bit of experience with programming in different languages. What i'm like to do is show a series of hands-on examples of the kinds of things I do on a regular basis. I've already got a few ideas jotted down, but I'm afraid that they might be either too advanced or too simple for the students to appreciate. Another concern is that a topic might be too long to explain and use too much time overall. Here are a few ideas : Program deployment using version control (git in my case) filtering apache logs using grep, awk, uniq, tail A couple of bash scripts that i've made for various stuff on servers live montitoring (htop, iotop, iptraf) creating databases and assigning roles in mysql/postgresql So, are these ideas any good ? Do you have better ideas ? are the ideas too simple and should I go for more "advanced" stuff ?

  Read the article

• SQL Server 2008 Express + Reporting Services on Windows 7

  - by TimothyP

  I'm trying to install SQL Server Express 2008 and Reporting Services on a x64 Windows 7 Machine for development purposes. I've installed SQL Server 2008 Express with the Microsoft Web Platform Installer I had to manually enable the SQL Server Browser in the Sql Server Configuration Manager and tried to enable the SQL Server Agent but that simply doesn't work. Keeps throwing an RPC error: "The remote procedure call failed. [0x800706be]". The start mode is set to Disabled and I cannot change it. Even though I selected the SQL Server Express with advanced services in the web platform installer I could not find any reference to SQL Server Reporting Services so I used the SQL Server Installation Center x64 application to "upgrade" to SQL Server Express 2008 with advanced services... this installed many things but still I couldn't find any reference to SQL Server Reporting Services other than an application called: "Reporting Services Configuration Manager" This opens up a dialog called "Reporting Services Configuration Connection" which is asking for a server name (shows the name of my machine) and a Find button. When I click the find button I get: "Unable to connect to the Reporting Server WMI provider. Details: Invalid Namespace". I found some references on the web to solve this problem, but they refer to a directory: "%ProgamFiles%\Microsoft SQL Server\MSRS10.SQL2008\Reporting Services\" which does not exist anywhere on my system. (The directories for SQL Server are there, but there is no Reporting Services directory anywhere). What am I doing wrong here? Wasn't the web platform installer supposed to handle all this? Thnx for any advice. PS: Most google results refer to 2005 vs 2008 problems, but I never had 2005 installed on this system, it's a newly installed development machine.

  Read the article

• pros and cons with server management gui tools to manage linux web servers

  - by ajsie

  i have stumbled upon these GUI tools that could help you manage your linux server through a web interface. ebox, webmin, ispconfig, zivios, ispcp, plesk, cpanel etc. i wonder what the pros and cons are with these solutions. a lot of people is saying that they are not as good as using pure command line (ssh) to manage your server. but i think thats yet another "linux are for advanced users" talk. i agree that a lot of things may only be done with the command line by editing directly in the configuration files. but i don't really want to do that every time and for everything. especially basic configurations these could manage. its like not having phpmyadmin for managing mysql. it would be a pain in the ass right? so if one wants to throw up a web server serving a php site oneself developed and wants all the usual stuff up and running (mysql, phpmyadmin, svn, webdav etc) is these tools the right way to go? and for more advanced features, one just use the terminal like old days. is this a smart way of managing a linux server? and which one would you choose? have you used any of these and could share your thoughts about them?

  Read the article

• Windows 7: Windows Firewall: Logging/Notifying on Outgoing Request Attempts

  - by Maxim Z.

  I'm trying to configure Windows Firewall with Advanced Security to log and tell me when programs are trying to make outbound requests. I previously tried installing ZoneAlarm, which worked wonders for me with this in XP, but now, I'm unable to install ZA on Win7. My question is, is it possible to somehow monitor a log or get notifications when a program tries to do that if I set all outbound connections to auto-block, so that I can then create a specific rule for the program and block it.? Thanks! UPDATE: I've enabled all the logging options available through the Properties windows of the Windows Firewall with Advanced Security Console, but I am only seeing logs in the %systemroot%\system32\LogFiles\Firewall\pfirewall.log file, not in the Event Viewer, as the first answer suggested. However, the logs that I can see only tell me the request's or response's destination IP and whether the connection was allowed or blocked, but it doesn't tell me what executable it comes from. I want to find out the file path of the executable that each blocked request comes from. So far, I haven't been able to.

  Read the article

• Biztalk 2009 logshipping with SQL 2008

  - by Manjot

  Hi, I am setting up biztalk logshipping for Biztalk 2009 database. Following http://msdn.microsoft.com/en-us/library/aa560961.aspx article, I am doing the following to setup biztalk logshipping on destination server: Enable Ad-hoc queries by: sp_configure 'show advanced options',1 go reconfigure go sp_configure 'Ad Hoc Distributed Queries',1 go reconfigure go sp_configure 'show advanced options',0 go reconfigure go Execute LogShipping_Destination_Schema & LogShipping_Destination_Logic in master on destinations server Run: exec bts_ConfigureBizTalkLogShipping @nvcDescription = '', @nvcMgmtDatabaseName = '', @nvcMgmtServerName = '', @SourceServerName = null, -- null indicates that this destination server restores all databases @fLinkServers = 1 -- 1 automatically links the server to the management database When I run this I am receiving the following error: Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. After some research I found some info : Usually this error means that the SQL Server Service Principal Name (SPN) was not configured, and NTLM was not being used as an authentication mechanism. SQl services are runing under different domain accounts. So, I asked the domain admin to create SPNs for the servers, SQL service accounts for beoth source and destination using name and FQDN. enabled computer name and service accounts for delegation. When I run the following: select * from sys.dm_exec_connections I get the the same error: Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON' Any help please?

  Read the article

< Previous Page | 226 227 228 229 230 231 232 233 234 235 236 237  | Next Page >