forward compatibility - Page 273

CISCO 2911 Router configuration

- by bala

Device cisco 2911 router configuration support is required please. I have exchange server 2010 configured and working without any errors the problem is in cisco router configuration when exchange server sends emails out the receives WAN IP not the public ip. I have configured RDNS lookups with our MX record IP addesses that match the FQDN but all our emails are rejected because it does not match with the public ip. Receiving mails problem is not an problem all mails are coming through. i am sure i am missing something on the router configuration that does not sends the public ip, can any one help me to solve this issue. Note; I've got 1 WAN IP & 8 Public IP from ISP . Find below the running configuration. Building configuration... Current configuration : 2734 bytes ! ! Last configuration change at 06:32:13 UTC Tue Apr 3 2012 ! NVRAM config last updated at 06:32:14 UTC Tue Apr 3 2012 ! NVRAM config last updated at 06:32:14 UTC Tue Apr 3 2012 version 15.1 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname BSBG-LL ! boot-start-marker boot-end-marker ! ! enable secret 5 $x$xHrxxxxx5ox0 enable password 7 xx23xx5FxxE1xx044 ! no aaa new-model ! no ipv6 cef ip source-route ip cef ! ! ! ! ! ip flow-cache timeout active 1 ip domain name yourdomain.com ip name-server 213.42.20.20 ip name-server 195.229.241.222 multilink bundle-name authenticated ! ! crypto pki token default removal timeout 0 ! ! license udi pid CISCO2911/K9 ! ! username bsbg ! ! ! ! ! ! interface Embedded-Service-Engine0/0 no ip address shutdown ! interface GigabitEthernet0/0 ip address 192.168.0.9 255.255.255.0 ip flow ingress ip nat inside ip virtual-reassembly in duplex auto speed 100 no cdp enable ! interface GigabitEthernet0/1 ip address 213.42.xx.x2 255.255.255.252 ip nat outside ip virtual-reassembly in duplex auto speed auto no cdp enable ! interface GigabitEthernet0/2 no ip address shutdown duplex auto speed auto ! ip forward-protocol nd ! no ip http server no ip http secure-server ! ip nat inside source list 120 interface GigabitEthernet0/1 overload ip nat inside source static tcp 192.168.0.4 25 94.56.89.100 25 extendable ip nat inside source static tcp 192.168.0.4 53 94.56.89.100 53 extendable ip nat inside source static udp 192.168.0.4 53 94.56.89.100 53 extendable ip nat inside source static tcp 192.168.0.4 110 94.56.89.100 110 extendable ip nat inside source static tcp 192.168.0.4 443 94.56.89.100 443 extendable ip nat inside source static tcp 192.168.0.4 587 94.56.89.100 587 extendable ip nat inside source static tcp 192.168.0.4 995 94.56.89.100 995 extendable ip nat inside source static tcp 192.168.0.4 3389 94.56.89.100 3389 extendable ip nat inside source static tcp 192.168.0.4 443 94.56.89.101 443 extendable ip nat inside source static tcp 192.168.0.12 80 94.56.89.102 80 extendable ip nat inside source static tcp 192.168.0.12 443 94.56.89.102 443 extendable ip nat inside source static tcp 192.168.0.12 3389 94.56.89.102 3389 extendable ip route 0.0.0.0 0.0.0.0 213.42.69.41 ! access-list 120 permit ip 192.168.0.0 0.0.0.255 any ! ! ! control-plane ! ! ! line con 0 exec-timeout 5 0 line aux 0 line 2 no activation-character no exec transport preferred none transport input all transport output pad telnet rlogin lapb-ta mop udptn v120 ssh stopbits 1 line vty 0 4 password 7 xx64xxD530D26086Dxx login transport input all ! scheduler allocate 20000 1000 end

Read the article

Replies to request coming over a relay goes to relay's internal IP, not to original request's source IP

- by seaquest

Dhcpd running on Linux gets a dhcp request over dhcrelay which is running on other remote machine. Oct 6 10:09:46 2012 dhcpd: DHCPDISCOVER from 00:1e:68:06:eb:37 (oguz-U300) via 172.16.17.81 tcpdump: listening on eth1, link-type EN10MB (Ethernet), capture size 96 bytes 10:35:01.112500 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto: UDP (17), length: 328) 192.168.0.81.67 > 192.168.0.1.67: BOOTP/DHCP, Request from 00:1e:68:06:eb:37, length: 300, hops:1, xid:0xe378fc7e, flags: [none] (0x0000) Gateway IP: 172.16.17.81 Client Ethernet Address: 00:1e:68:06:eb:37 [|bootp] It matches to a subnet and send reply. However reply does not go to the requesting dhcrelay external IP(192.168.0.81). Instead, it goes to the internal interface IP of machine running dhcrelay. And I think because of this remote machine running dhcrelay or the dhcrealy itself discarding packet. Oct 6 10:09:46 2012 dhcpd: DHCPOFFER on 172.16.17.11 to 00:1e:68:06:eb:37 (oguz-U300) via 172.16.17.81 10:35:02.050108 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto: UDP (17), length: 328) 192.168.0.1.67 > 172.16.17.81.67: BOOTP/DHCP, Reply, length: 300, hops:1, xid:0xe378fc7e, flags: [none] (0x0000) Your IP: 172.16.17.11 Gateway IP: 172.16.17.81 Client Ethernet Address: 00:1e:68:06:eb:37 [|bootp] Is this a normal behaviour? Machine running dhcrelay: eth1(ext) Link encap:Ethernet HWaddr 00:90:0B:21:43:F4 inet addr:192.168.0.81 Bcast:192.168.0.255 Mask:255.255.255.0 eth2(int) Link encap:Ethernet HWaddr 00:90:0B:21:43:F5 inet addr:172.16.17.81 Bcast:172.16.17.255 Mask:255.255.255.0 3582 ? Ss 0:00 /usr/sbin/dhcrelay -i eth2 192.168.0.1 Machine running dhcpd: eth1 Link encap:Ethernet HWaddr 00:90:0B:23:97:D1 inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0 option domain-name "test.com"; option subnet-mask 255.255.255.0; authoritative; ignore client-updates; ddns-update-style ad-hoc; default-lease-time 86400; max-lease-time 86400; subnet 192.168.0.0 netmask 255.255.255.0 { range 192.168.0.135 192.168.0.169; option broadcast-address 192.168.0.255; option domain-name-servers 192.168.0.1; option domain-name "test.com"; option routers 192.168.0.1; } subnet 172.16.17.0 netmask 255.255.255.0 { local-address 192.168.0.1; server-identifier 192.168.0.1; range 172.16.17.10 172.16.17.11; option broadcast-address 172.16.17.255; option routers 172.16.17.81; } (I put local-address and server-identifier. But this does not help ) Regards, -- Oguz YILMAZ UPDATE: The first problem is found. I have configured dhcrelay only on listening internel interface. It seems (of course) is should also listen to external interface for replies. It appears it is not important where the packet destined to. dhrelay will forward it to internal net. HOWEVER, I have deleted route on dhcpd server to reach 172.16.17.x subnet. It again tries to send reply to 172.16.17.81. Because it does not know the route it send it from default gateway to the internet. eth0: IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto: UDP (17), length: 328) 192.168.1.2.67 > 172.16.17.81.67: BOOTP/DHCP, Reply, length: 300, hops:1, xid:0x32830125, secs:3, flags: [none] (0x0000) eth0: Your IP: 172.16.17.11 eth0: Gateway IP: 172.16.17.81 eth0: Client Ethernet Address: 00:1e:68:06:eb:37 [|bootp] How can I force dhcpd to force to send replies to requesting IP? Because, it is not much meaningful to add routes to subnet we distribute IP for. Internet - dhcpd - 192.168.0.1 - SOMENET - 192.168.0.81 - dhcrelay - 172.16.17.0/24 192.168.0.1 has no route for 172.16.17.0 and has no interface directly attached to that net.

Read the article

Reading XML File

- by Joy

I'm developping an iphone application which uses google weather api to forecast the weather. The webservice is giving me data in the following format:- <?xml version="1.0"?> <xml_api_reply version="1"> <weather module_id="0" tab_id="0" mobile_row="0" mobile_zipped="1" row="0" section="0" > <forecast_information> <city data="Kolkata, West Bengal"/> <postal_code data="Kolkata"/> <latitude_e6 data=""/> <longitude_e6 data=""/> <forecast_date data="2010-04-28"/> <current_date_time data="2010-04-28 10:20:00 +0000"/> <unit_system data="US"/> </forecast_information> <current_conditions ><condition data="Haze"/> <temp_f data="97"/> <temp_c data="36"/> <humidity data="Humidity: 53%"/> <icon data="/ig/images/weather/haze.gif"/> <wind_condition data="Wind: S at 12 mph"/> </current_conditions> <forecast_conditions> <day_of_week data="Wed"/> <low data="82"/> <high data="91"/> <icon data="/ig/images/weather/chance_of_rain.gif"/> <condition data="Chance of Rain"/> </forecast_conditions> <forecast_conditions> <day_of_week data="Thu"/> <low data="82"/> <high data="96"/> <icon data="/ig/images/weather/rain.gif"/> <condition data="Rain"/> </forecast_conditions> <forecast_conditions> <day_of_week data="Fri"/> <low data="82"/> <high data="96"/> <icon data="/ig/images/weather/sunny.gif"/> <condition data="Clear"/> </forecast_conditions> <forecast_conditions> <day_of_week data="Sat"/> <low data="78"/> <high data="98"/> <icon data="/ig/images/weather/mostly_sunny.gif"/> <condition data="Mostly Sunny"/> </forecast_conditions> </weather> As I'm new to iPhone development so i'm facing problem while reading this using xmlparser. Please help me out of this problem. Looking forward to your valuable reply. Thanks in advance..

Read the article

Remote Desktop Services Gateway Issue

- by AVandelay05

Alright fellow techies here's the rundown. I have installed Server 2008 r2 Remote Dekstop Services on a VM in my network. I installed the following RD role services: RD Session Host, Licensing, Connection Broker, Gateway, Web Access. When I set things up originally, the gateway server and RDWeb worked as it should locally. After getting things running locally (remoteserver.domainname.local) I wanted to test things externally. From the outside, I couldn't get things running (meaning I could connect to rdweb access externally, but when I tried to run an app I would get the message "can't connect/find computer"). Here's my setup for external access The VM has every RD Services role services installed on it, meaning it acts as gateway, rd web access, session host, licensing, the whole bit. I made a self-signed certificate on the gateway server (gateway.domainname.net is the cert name). Internally, I have a secondary forward-lookup zone called domainname.net with an A record gateway pointing to the local IP of the gateway server. On our public DNS (domainname.net) I have an A record gateway. This is to access the RDWeb externally. In IIS I have the following authentication settings RDWeb: All disabled except for anonymous authentication Rpc: All disabled except for basic and windows RpcWithCert: All disbled except for windows authentication I have the necessary web access config in our sonicwall tz210 (https and rdp, external ip pointing to local ip of rds server) RAP and CAP have the correct user and computer groups, authentication, and allowed devices After all of this, here's what happens accessing externally. I can login correctly to RDWeb Access (I've tried a bogus login, I can't login to it so that's working properly). I see the Apps for use. I click on an app, click connect, the credential window opens, I put in the correct user creds, it tries to connect to the gateway server, but then the cred window comes back in view. I tried to reach a limit of failed logins, but never reached one, haha. So from the same external client machine I try to connect to the gateway through a Remote Desktop connection. I put in the correct gateway settings in the RD window, try to connect and get the same results as I did in RDWeb access. I checked the event logs on the RD Services machine and saw the following event IDs around the time I tried to login externally: ID 6037 with the message "The program svchost.exe, with the assigned process ID 2168, could not authenticate locally by using the target name host/gateway.domainname.net. The target name used is not valid. A target name should refer to one of the local computer names, for example, the DNS host name. Try a different target name." ID 10 RADWebAccess "RD Web Access was unable to access gateway.domainname.net, which is the server that is specified as running the RemoteApp and Desktop Connection Management service. Ensure that the computer account of the RD Web Access server is a member of the TS Web Access Computers security group on gateway.domainname.net" ID 4625 "An account failed to log on. Subject: Security ID: NULL SID Account Name: - Account Domain: - Logon ID: 0x0 Logon Type: 3 Account For Which Logon Failed: Security ID: NULL SID Account Name: Administrator Account Domain: gateway.domainname.net Failure Information: Failure Reason: Unknown user name or bad password. Status: 0xc000006d Sub Status: 0xc000006a Process Information: Caller Process ID: 0x0 Caller Process Name: - Network Information: Workstation Name: USER-LAPTOP Source Network Address: External IP Source Port: 63125 Detailed Authentication Information: Logon Process: NtLmSsp Authentication Package: NTLM Transited Services: - Package Name (NTLM only): - Key Length: 0 This event is generated when a logon request fails. It is generated on the computer where access was attempted. The Subject fields indicate the account on the local system which requested the logon. This is most commonly a service such as the Server service, or a local process such as Winlogon.exe or Services.exe. The Logon Type field indicates the kind of logon that was requested. The most common types are 2 (interactive) and 3 (network). The Process Information fields indicate which account and process on the system requested the logon. The Network Information fields indicate where a remote logon request originated. Workstation name is not always available and may be left blank in some cases. The authentication information fields provide detailed information about this specific logon request. - Transited services indicate which intermediate services have participated in this logon request. - Package name indicates which sub-protocol was used among the NTLM protocols." I don't think the VM has a null SID. The SID of the VM and it's physical host have different SIDS. I can access the blank page for rpc externally using the external gateway name. It seems like authentication is a problem. Also, is it a problem that the external name of the gateway server doesn't match the local name? The external name (which the cert is based on) is gateway.domainname.net and the internal name is remoteserver.domainname.local. That's the only thing I can think of that would be the problem, but the external name has to be different from the local right? Internally, I ping gateway.domainname.net and it gives me the correct local IP of the server. Now, there isn't an actual computer name in AD, but I don't know how I would achieve that? I hope I've been clear....any help would be appreciated. I think I'm close to achieving this. :)

Read the article

Tomcat 7 on Ubuntu 12.04 with JRE 7 not starting

- by Andreas Krueger

I am running a virtual server in the web on Ubuntu 12.04 LTS / 32 Bit. After a clean install of JRE 7 and Tomcat 7, following the instructions on http://www.sysadminslife.com, I don't get Tomcat 7 up and running. > java -version java version "1.7.0_09" Java(TM) SE Runtime Environment (build 1.7.0_09-b05) Java HotSpot(TM) Client VM (build 23.5-b02, mixed mode) > /etc/init.d/tomcat start Starting Tomcat Using CATALINA_BASE: /usr/local/tomcat Using CATALINA_HOME: /usr/local/tomcat Using CATALINA_TMPDIR: /usr/local/tomcat/temp Using JRE_HOME: /usr/lib/jvm/java-7-oracle Using CLASSPATH: /usr/local/tomcat/bin/bootstrap.jar:/usr/local/tomcat/bin/tomcat-juli.jar > telnet localhost 8080 Trying ::1... Trying 127.0.0.1... telnet: Unable to connect to remote host: Connection refused netstat sometimes shows a Java process, most of the times not. If it does, nothing works either. Does anyone have a solution or encountered similar situations? Here are the contents of catalina.out: 16.11.2012 18:36:39 org.apache.catalina.core.AprLifecycleListener init INFO: The APR based Apache Tomcat Native library which allows optimal performance in production environments was not found on the java.library.path: /usr/lib/jvm/java-6-oracle/lib/i386/client:/usr/lib/jvm/java-6-oracle/lib/i386:/usr/lib/jvm/java-6-oracle/../lib/i386:/usr/java/packages/lib/i386:/lib:/usr/lib 16.11.2012 18:36:40 org.apache.coyote.AbstractProtocol init INFO: Initializing ProtocolHandler ["http-bio-8080"] 16.11.2012 18:36:40 org.apache.coyote.AbstractProtocol init INFO: Initializing ProtocolHandler ["ajp-bio-8009"] 16.11.2012 18:36:40 org.apache.catalina.startup.Catalina load INFO: Initialization processed in 1509 ms 16.11.2012 18:36:40 org.apache.catalina.core.StandardService startInternal INFO: Starting service Catalina 16.11.2012 18:36:40 org.apache.catalina.core.StandardEngine startInternal INFO: Starting Servlet Engine: Apache Tomcat/7.0.29 16.11.2012 18:36:40 org.apache.catalina.startup.HostConfig deployDirectory INFO: Deploying web application directory /usr/local/tomcat/webapps/manager Here come the results of ps -ef, iptables --list and netstat -plut: > ps -ef UID PID PPID C STIME TTY TIME CMD root 1 0 0 Nov16 ? 00:00:00 init root 2 1 0 Nov16 ? 00:00:00 [kthreadd/206616] root 3 2 0 Nov16 ? 00:00:00 [khelper/2066167] root 4 2 0 Nov16 ? 00:00:00 [rpciod/2066167/] root 5 2 0 Nov16 ? 00:00:00 [rpciod/2066167/] root 6 2 0 Nov16 ? 00:00:00 [rpciod/2066167/] root 7 2 0 Nov16 ? 00:00:00 [rpciod/2066167/] root 8 2 0 Nov16 ? 00:00:00 [nfsiod/2066167] root 119 1 0 Nov16 ? 00:00:00 upstart-udev-bridge --daemon root 125 1 0 Nov16 ? 00:00:00 /sbin/udevd --daemon root 157 125 0 Nov16 ? 00:00:00 /sbin/udevd --daemon root 158 125 0 Nov16 ? 00:00:00 /sbin/udevd --daemon root 205 1 0 Nov16 ? 00:00:00 upstart-socket-bridge --daemon root 276 1 0 Nov16 ? 00:00:00 /usr/sbin/sshd -D root 335 1 0 Nov16 ? 00:00:00 /usr/sbin/xinetd -dontfork -pidfile /var/run/xinetd.pid -stayalive -inetd root 348 1 0 Nov16 ? 00:00:00 cron syslog 368 1 0 Nov16 ? 00:00:00 /sbin/syslogd -u syslog root 472 1 0 Nov16 ? 00:00:00 /usr/lib/postfix/master postfix 482 472 0 Nov16 ? 00:00:00 qmgr -l -t fifo -u root 520 1 0 Nov16 ? 00:00:04 /usr/sbin/apache2 -k start www-data 523 520 0 Nov16 ? 00:00:00 /usr/sbin/apache2 -k start www-data 525 520 0 Nov16 ? 00:00:00 /usr/sbin/apache2 -k start www-data 526 520 0 Nov16 ? 00:00:00 /usr/sbin/apache2 -k start tomcat 1074 1 0 Nov16 ? 00:01:08 /usr/lib/jvm/java-6-oracle/bin/java -Djava.util.logging.config.file=/usr/ postfix 1351 472 0 Nov16 ? 00:00:00 tlsmgr -l -t unix -u -c postfix 3413 472 0 17:00 ? 00:00:00 pickup -l -t fifo -u -c root 3457 276 0 17:31 ? 00:00:00 sshd: root@pts/0 root 3459 3457 0 17:31 pts/0 00:00:00 -bash root 3470 3459 0 17:31 pts/0 00:00:00 ps -ef > iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT tcp -- anywhere anywhere tcp dpt:http-alt ACCEPT tcp -- anywhere anywhere tcp dpt:8005 ACCEPT tcp -- anywhere anywhere tcp dpt:http-alt Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination > netstat -plut Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 *:smtp *:* LISTEN 472/master tcp 0 0 *:3213 *:* LISTEN 276/sshd tcp6 0 0 [::]:smtp [::]:* LISTEN 472/master tcp6 0 0 [::]:8009 [::]:* LISTEN 1074/java tcp6 0 0 [::]:3213 [::]:* LISTEN 276/sshd tcp6 0 0 [::]:http-alt [::]:* LISTEN 1074/java tcp6 0 0 [::]:http [::]:* LISTEN 520/apache2

Read the article

how to use multiple tab controls, and to be able to call a selected tab control with buttons.

- by mojotaker

Please I am trying to assign each button on the left its own Tab control. That is for example, when the Intake form button is pushed, it will have its own set of tabs (its own tabcontrols) am i supposed to place multiple tab controls on the artboard, or is there a way to programatically change the names of the tabs, and there contents, when a button is pushed on the left ? thank you in advance. and here is a link hxxp://img709.imageshack.us/img709/554/tabcontrol.gif here is the code so far <Window xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:d="http://schemas.microsoft.com/expression/blend/2008" xmlns:mc="http://schemas.openxmlformats.org/markup-compatibility/2006" x:Class="service.MainWindow" x:Name="Window" Title="MainWindow" Width="687" Height="480" mc:Ignorable="d"> <Window.Resources> <Storyboard x:Key="OnLoaded1"/> </Window.Resources> <Window.Triggers> <EventTrigger RoutedEvent="FrameworkElement.Loaded"> <BeginStoryboard Storyboard="{StaticResource OnLoaded1}"/> </EventTrigger> </Window.Triggers> <Grid x:Name="LayoutRoot" Margin="0,0,-16,1"> <Grid.ColumnDefinitions> <ColumnDefinition Width="0*"/> <ColumnDefinition/> </Grid.ColumnDefinitions> <DockPanel Margin="8,8,0,7" LastChildFill="False" Grid.Column="1" HorizontalAlignment="Left" Width="660"> <Menu VerticalAlignment="Top" Width="657" Height="32"> <MenuItem x:Name="file" Header="File"/> <MenuItem x:Name="edit" Header="Edit"> <MenuItem Width="100" Height="100" Header="MenuItem"/> </MenuItem> <MenuItem x:Name="view" Header="View"/> <MenuItem x:Name="preferences" Header="Preferences"/> <MenuItem x:Name="help" Header="Help"/> </Menu> </DockPanel> <TabControl x:Name="tabwin" Margin="137.224,46,19,7" Grid.Column="1"> <TabItem x:Name="intakeformsub" Header="Elegibility Form"> <Grid HorizontalAlignment="Left" Width="490"/> </TabItem> <TabItem Header="TabItem"> <Grid/> </TabItem> <TabItem Header="TabItem"> <Grid/> </TabItem> <TabItem Header="TabItem"> <Grid> <Grid.ColumnDefinitions> <ColumnDefinition Width="0.567*"/> <ColumnDefinition Width="0.433*"/> </Grid.ColumnDefinitions> </Grid> </TabItem> <TabItem Header="TabItem"> <Grid/> </TabItem> <TabItem Header="TabItem"> <Grid> <Grid.ColumnDefinitions> <ColumnDefinition Width="0.735*"/> <ColumnDefinition Width="0.265*"/> </Grid.ColumnDefinitions> </Grid> </TabItem> <TabItem Header="TabItem"> <Grid/> </TabItem> <TabItem Header="TabItem"> <Grid/> </TabItem> </TabControl> <Grid x:Name="___buttontab" Margin="11.205,61,0,0" Grid.Column="1" HorizontalAlignment="Left" Width="122.019" VerticalAlignment="Top" Height="276"> <Button VerticalAlignment="Top" Height="36" Content="Button"/> <Button Margin="0,40,0,0" Content="Oasis Assessments" VerticalAlignment="Top" Height="36"/> <Button Margin="0,80,0,0" VerticalAlignment="Top" Height="36" Content="Plan of Care"/> <Button Margin="0,120,0,0" VerticalAlignment="Top" Height="36" Content="Medication Profile" RenderTransformOrigin="0.421,5.556"/> <Button Margin="0,0,0,80" VerticalAlignment="Bottom" Height="36" Content="Clinical Notes"/> <Button Margin="0,0,0,40" VerticalAlignment="Bottom" Height="36" Content="Infection Control"/> <Button x:Name="intakeformbtn" VerticalAlignment="Top" Height="36" Content="Intake Form" Click="intakeform"> <Button.BindingGroup> <BindingGroup/> </Button.BindingGroup> </Button> <Button VerticalAlignment="Bottom" Height="36" Content="Discharge Summary"/> </Grid> <ProgressBar HorizontalAlignment="Left" Margin="8,0,0,7" VerticalAlignment="Bottom" Width="104.795" Height="19" Grid.Column="1"/> </Grid> </Window>

Read the article

How can I make this Java code run faster?

- by Martin Wiboe

Hello all, I am trying to make a Java port of a simple feed-forward neural network. This obviously involves lots of numeric calculations, so I am trying to optimize my central loop as much as possible. The results should be correct within the limits of the float data type. My current code looks as follows (error handling & initialization removed): /** * Simple implementation of a feedforward neural network. The network supports * including a bias neuron with a constant output of 1.0 and weighted synapses * to hidden and output layers. * * @author Martin Wiboe */ public class FeedForwardNetwork { private final int outputNeurons; // No of neurons in output layer private final int inputNeurons; // No of neurons in input layer private int largestLayerNeurons; // No of neurons in largest layer private final int numberLayers; // No of layers private final int[] neuronCounts; // Neuron count in each layer, 0 is input // layer. private final float[][][] fWeights; // Weights between neurons. // fWeight[fromLayer][fromNeuron][toNeuron] // is the weight from fromNeuron in // fromLayer to toNeuron in layer // fromLayer+1. private float[][] neuronOutput; // Temporary storage of output from previous layer public float[] compute(float[] input) { // Copy input values to input layer output for (int i = 0; i < inputNeurons; i++) { neuronOutput[0][i] = input[i]; } // Loop through layers for (int layer = 1; layer < numberLayers; layer++) { // Loop over neurons in the layer and determine weighted input sum for (int neuron = 0; neuron < neuronCounts[layer]; neuron++) { // Bias neuron is the last neuron in the previous layer int biasNeuron = neuronCounts[layer - 1]; // Get weighted input from bias neuron - output is always 1.0 float activation = 1.0F * fWeights[layer - 1][biasNeuron][neuron]; // Get weighted inputs from rest of neurons in previous layer for (int inputNeuron = 0; inputNeuron < biasNeuron; inputNeuron++) { activation += neuronOutput[layer-1][inputNeuron] * fWeights[layer - 1][inputNeuron][neuron]; } // Store neuron output for next round of computation neuronOutput[layer][neuron] = sigmoid(activation); } } // Return output from network = output from last layer float[] result = new float[outputNeurons]; for (int i = 0; i < outputNeurons; i++) result[i] = neuronOutput[numberLayers - 1][i]; return result; } private final static float sigmoid(final float input) { return (float) (1.0F / (1.0F + Math.exp(-1.0F * input))); } } I am running the JVM with the -server option, and as of now my code is between 25% and 50% slower than similar C code. What can I do to improve this situation? Thank you, Martin Wiboe

Read the article

MSBuild condition across projects

- by Billy Talented

I have tried several solutions for this problem. Enough to know I do not know enough about MSBuild to do this elegantly but I feel like there should be a method. I have a set of libraries for working with .net projects. A few of the projects utilize System.Web.Mvc - which recently released Version 2 - and we are looking forward to the upgrade. Currently sites which reference this library reference it directly by the project(csproj) on the developer's computer - not a built version of the library so that changes and source code case easily be viewed when dealing code from this library. This works quite well and would prefer to not have to switch to binary references (but will if this is the only solution). The problem I have is that because of some of the functionality that was added onto the MVC1 based library (view engines, model binders etc) several of the sites reliant on these libraries need to stay on MVC1 until we have full evaluated and tested them on MVC2. I would prefer to not have to fork or have two copies on each dev machine. So what I would like to be able to do is set a property group value in the referencing web application and have this read by the above mentions library with the caviat that when working directly on the library via its containing solution I would like to be able to control this via Configuration Manager by selecting a build type and that property overriding the build behavior of the solution (i.e. 'Debug - MVC1' vs 'Debug -MVC2') - I have this working via: <Choose> <When Condition=" '$(Configuration)|$(Platform)' == 'Release - MVC2|AnyCPU' Or '$(Configuration)|$(Platform)' == 'Debug - MVC2|AnyCPU'"> <ItemGroup> <Reference Include="System.Web.Mvc, Version=2.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35, processorArchitecture=MSIL"> </Reference> <Reference Include="Microsoft.Web.Mvc, Version=1.0.0.0, Culture=neutral, processorArchitecture=MSIL"> <SpecificVersion>False</SpecificVersion> <HintPath>..\Dependancies\Web\MVC2\Microsoft.Web.Mvc.dll</HintPath> </Reference> </ItemGroup> </When> <Otherwise> <ItemGroup> <Reference Include="System.Web.Mvc, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35, processorArchitecture=MSIL"> <SpecificVersion>False</SpecificVersion> <HintPath>..\Dependancies\Web\MVC\System.Web.Mvc.dll</HintPath> </Reference> </ItemGroup> </Otherwise> The item that I am struggling with is the cross solution issue(solution TheWebsite references this project and needs to control which build property to use) that I have not found a way to work with that I think is a solid solution that enabled the build within visual studio to work as it has to date. Other bits: we are using VS2008, Resharper, TeamCity for CI, SVN for source control.

Read the article

Function signature-like expressions as C++ template arguments

- by Jeff Lee

I was looking at Don Clugston's FastDelegate mini-library and noticed a weird syntactical trick with the following structure: TemplateClass< void( int, int ) > Object; It almost appears as if a function signature is being used as an argument to a template instance declaration. This technique (whose presence in FastDelegate is apparently due to one Jody Hagins) was used to simplify the declaration of template instances with a semi-arbitrary number of template parameters. To wit, it allowed this something like the following: // A template with one parameter template<typename _T1> struct Object1 { _T1 m_member1; }; // A template with two parameters template<typename _T1, typename _T2> struct Object2 { _T1 m_member1; _T2 m_member2; }; // A forward declaration template<typename _Signature> struct Object; // Some derived types using "function signature"-style template parameters template<typename _Dummy, typename _T1> struct Object<_Dummy(_T1)> : public Object1<_T1> {}; template<typename _Dummy, typename _T1, typename _T2> struct Object<_Dummy(_T1, _T2)> : public Object2<_T1, _T2> {}; // A. "Vanilla" object declarations Object1<int> IntObjectA; Object2<int, char> IntCharObjectA; // B. Nifty, but equivalent, object declarations typedef void UnusedType; Object< UnusedType(int) > IntObjectB; Object< UnusedType(int, char) > IntCharObjectB; // C. Even niftier, and still equivalent, object declarations #define DeclareObject( ... ) Object< UnusedType( __VA_ARGS__ ) > DeclareObject( int ) IntObjectC; DeclareObject( int, char ) IntCharObjectC; Despite the real whiff of hackiness, I find this kind of spoofy emulation of variadic template arguments to be pretty mind-blowing. The real meat of this trick seems to be the fact that I can pass textual constructs like "Type1(Type2, Type3)" as arguments to templates. So here are my questions: How exactly does the compiler interpret this construct? Is it a function signature? Or, is it just a text pattern with parentheses in it? If the former, then does this imply that any arbitrary function signature is a valid type as far as the template processor is concerned? A follow-up question would be that since the above code sample is valid code, why doesn't the C++ standard just allow you to do something like the following, which is does not compile? template<typename _T1> struct Object { _T1 m_member1; }; // Note the class identifier is also "Object" template<typename _T1, typename _T2> struct Object { _T1 m_member1; _T2 m_member2; }; Object<int> IntObject; Object<int, char> IntCharObject;

Read the article

C++ std::vector problems

- by Faur Ioan-Aurel

For 2 days i tried to explain myself some of the things that are happening in my c++ code,and i can't get a good explanation.I must say that i'm more a java programmer.Long time i used quite a bit the C language but i guess Java erased those skills and now i'm hitting a wall trying to port a few classes from java to c++. So let's say that we have this 2 classes: class ForwardNetwork { protected: ForwardLayer* inputLayer; ForwardLayer* outputLayer; vector<ForwardLayer* > layers; public: void ForwardNetwork::getLayers(std::vector< ForwardLayer* >& result ) { for(int i= 0 ;i< layers.size(); i++){ ForwardLayer* lay = dynamic_cast<ForwardLayer*>(this->layers.at(i)); if(lay != NULL) result.push_back(lay); else cout << "Layer at#" << i << " is null" << endl; } } void ForwardNetwork::addLayer ( ForwardLayer* layer ) { if(layer != NULL) cout << "Before push layer is not null" << endl; //setup the forward and back pointer if ( this->outputLayer != NULL ) { layer->setPrevious ( this->outputLayer ); this->outputLayer->setNext ( layer ); } //update the input layer and outputLayer variables if ( this->layers.size() == 0 ) this->inputLayer = this->outputLayer = layer; else this->outputLayer = layer; //push layer in vector this->layers.push_back ( layer ); for(int i = 0; i< layers.size();i++) if(layers[i] != NULL) cout << "Check::Layer[" << i << "] is not null!" << endl; } }; Second class: class Backpropagation : public Train { public: Backpropagation::Backpropagation ( FeedForwardNetwork* network ){ this->network = network; vector<FeedforwardLayer*> vec; network->getLayers(vec); } }; Now if i add from main() some layers into network via addLayer(..) method it's all good.My vector is just as it should.But after i call Backpropagation() constructor with a network object ,when i enter getLayers(), some of my objects from vector have their address set to NULL(they are randomly chosen:for example if i run my app once with 3 layer's into vector ,the first object from vector is null.If i run it second time first 2 objects are null,third time just first object null and so on). Now i can't explain why this is happening.I must say that all the objects that should be in vector they also live inside the network and they are not NULL; This happens everywhere after i done with addLayer() so not just in the getLayers(). I cant get a good grasp to this problem.I thought first that i might modify my vector.But i can't find such thing. Also why if the reference from vector is NULL ,the reference that lives inside ForwardNetwork as a linked list (inputLayer and outputLayer) is not NULL? I must ask for your help.Please ,if you have some advices don't hesitate! PS: as compiler i use g++ part of gcc 4.6.1 under ubuntu 11.10

Read the article

LevelToVisibilityConverter in silverligt 4

- by prince23

<UserControl x:Class="SLGridImage.MainPage" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:d="http://schemas.microsoft.com/expression/blend/2008" xmlns:mc="http://schemas.openxmlformats.org/markup-compatibility/2006" mc:Ignorable="d" d:DesignHeight="300" d:DesignWidth="400" xmlns:sdk="http://schemas.microsoft.com/winfx/2006/xaml/presentation/sdk"> <UserControl.Resources> <local:LevelToVisibilityConverter x:Key="LevelToVisibility" /> </UserControl.Resources> <Grid x:Name="LayoutRoot" Background="White"> <sdk:DataGrid x:Name="dgMarks" CanUserResizeColumns="False" SelectionMode="Single" AutoGenerateColumns="False" VerticalAlignment="Top" ItemsSource="{Binding MarkCollection}" IsReadOnly="True" Margin="13,44,0,0" RowDetailsVisibilityMode="Collapsed" Height="391" HorizontalAlignment="Left" Width="965" VerticalScrollBarVisibility="Visible" > <sdk:DataGrid.Columns> <sdk:DataGridTemplateColumn> <sdk:DataGridTemplateColumn.CellTemplate> <DataTemplate> <Button x:Name="myButton" Click="myButton_Click"> <StackPanel Orientation="Horizontal"> <Image Margin="2, 2, 2, 2" x:Name="imgMarks" Stretch="Fill" Width="12" Height="12" Source="Images/test.png" VerticalAlignment="Center" HorizontalAlignment="Center" Visibility="{Binding Level, Converter={StaticResource LevelToVisibility}}" /> <TextBlock Text="{Binding Level}" TextWrapping="NoWrap" ></TextBlock> </StackPanel> </Button> </DataTemplate> </sdk:DataGridTemplateColumn.CellTemplate> </sdk:DataGridTemplateColumn> <sdk:DataGridTemplateColumn Header="Name" > <sdk:DataGridTemplateColumn.CellTemplate> <DataTemplate > <Border> <TextBlock Text="{Binding Name}" /> </Border> </DataTemplate> </sdk:DataGridTemplateColumn.CellTemplate> </sdk:DataGridTemplateColumn> <sdk:DataGridTemplateColumn Header="Marks" Width="80"> <sdk:DataGridTemplateColumn.CellTemplate> <DataTemplate> <Border> <TextBlock Text="{Binding Marks}" /> </Border> </DataTemplate> </sdk:DataGridTemplateColumn.CellTemplate> </sdk:DataGridTemplateColumn> </sdk:DataGrid.Columns> </sdk:DataGrid> </Grid> </UserControl> in .cs using System; using System.Collections.Generic; using System.Linq; using System.Net; using System.Windows; using System.Windows.Controls; using System.Windows.Documents; using System.Windows.Input; using System.Windows.Media; using System.Windows.Media.Animation; using System.Windows.Shapes; using System.Collections.ObjectModel; using System.ComponentModel; namespace SLGridImage { public partial class MainPage : UserControl { private MarksViewModel model = new MarksViewModel(); public MainPage() { InitializeComponent(); this.DataContext = model; } private void myButton_Click(object sender, RoutedEventArgs e) { } } public class MarksViewModel : INotifyPropertyChanged { public MarksViewModel() { markCollection.Add(new Mark() { Name = "ABC", Marks = 23, Level = 0 }); markCollection.Add(new Mark() { Name = "XYZ", Marks = 67, Level = 1 }); markCollection.Add(new Mark() { Name = "YU", Marks = 56, Level = 0 }); markCollection.Add(new Mark() { Name = "AAA", Marks = 89, Level = 1 }); } private ObservableCollection<Mark> markCollection = new ObservableCollection<Mark>(); public ObservableCollection<Mark> MarkCollection { get { return this.markCollection; } set { this.markCollection = value; OnPropertyChanged("MarkCollection"); } } public event PropertyChangedEventHandler PropertyChanged; public void OnPropertyChanged(string propName) { if (PropertyChanged != null) this.PropertyChanged(this, new PropertyChangedEventArgs(propName)); } } public class Mark { public string Name { get; set; } public int Marks { get; set; } public int Level { get; set; } } public class LevelToVisibilityConverter : System.Windows.Data.IValueConverter { #region IValueConverter Members public object Convert(object value, Type targetType, object parameter, System.Globalization.CultureInfo culture) { Visibility isVisible = Visibility.Collapsed; if ((value == null)) return isVisible; int condition = (int)value; isVisible = condition == 1 ? Visibility.Visible : Visibility.Collapsed; return isVisible; } public object ConvertBack(object value, Type targetType, object parameter, System.Globalization.CultureInfo culture) { throw new NotImplementedException(); } #endregion } } when i run getting error The type 'local:LevelToVisibilityConverter' was not found. Verify that you are not missing an assembly reference and that all referenced assemblies have been built. what i am i missing here looking forward for an solution thank you

Read the article

How do I set up ServletForwardingController to intercept for jsp requests on weblogic

- by dok

My end goal is to be able to use the spring message tag with configured messageSource on a legacy app using a model-1 architecture. I've done this in tomcat with something like <bean id="messageSource" class="org.springframework.context.support.ReloadableResourceBundleMessageSource"> <property name="basename" value="WEB-INF/classes/bundle"/> </bean> <bean id="urlMapping" class="org.springframework.web.servlet.handler.SimpleUrlHandlerMapping"> <property name="mappings"> <props> <prop key="*">myServletForwardingController</prop> </props> </property> </bean> <bean id="myServletForwardingController" name="/**/*.jsp" class="org.springframework.web.servlet.mvc.ServletForwardingController"> <property name="servletName" value="jsp"/> </bean> For weblogic I have <bean id="messageSource" class="org.springframework.context.support.ReloadableResourceBundleMessageSource"> <property name="basenames"> <list> <value>WEB-INF/i18n/bundle</value> </list> </property> </bean> <bean name="/**/*.jsp" class="org.springframework.web.servlet.mvc.ServletForwardingController"> <property name="servletName" value="JspServlet"/> </bean> But, no luck. I'm getting a StackOverflowError when I attempt to access a JSP. java.lang.StackOverflowError at java.lang.ClassLoader.defineClass1(Native Method) at java.lang.ClassLoader.defineClass(ClassLoader.java:620) at java.security.SecureClassLoader.defineClass(SecureClassLoader.java:124) at weblogic.utils.classloaders.GenericClassLoader.defineClass(GenericClassLoader.java:338) at weblogic.utils.classloaders.GenericClassLoader.findLocalClass(GenericClassLoader.java:291) at weblogic.utils.classloaders.GenericClassLoader.findClass(GenericClassLoader.java:259) at weblogic.utils.classloaders.ChangeAwareClassLoader.findClass(ChangeAwareClassLoader.java:54) at java.lang.ClassLoader.loadClass(ClassLoader.java:306) at java.lang.ClassLoader.loadClass(ClassLoader.java:251) at weblogic.utils.classloaders.GenericClassLoader.loadClass(GenericClassLoader.java:179) at weblogic.utils.classloaders.ChangeAwareClassLoader.loadClass(ChangeAwareClassLoader.java:35) at java.lang.ClassLoader.loadClassInternal(ClassLoader.java:319) at java.lang.ClassLoader.defineClass1(Native Method) at java.lang.ClassLoader.defineClass(ClassLoader.java:620) at java.security.SecureClassLoader.defineClass(SecureClassLoader.java:124) at weblogic.utils.classloaders.GenericClassLoader.defineClass(GenericClassLoader.java:338) at weblogic.utils.classloaders.GenericClassLoader.findLocalClass(GenericClassLoader.java:291) at weblogic.utils.classloaders.GenericClassLoader.findClass(GenericClassLoader.java:259) at weblogic.utils.classloaders.ChangeAwareClassLoader.findClass(ChangeAwareClassLoader.java:54) at java.lang.ClassLoader.loadClass(ClassLoader.java:306) at java.lang.ClassLoader.loadClass(ClassLoader.java:251) at weblogic.utils.classloaders.GenericClassLoader.loadClass(GenericClassLoader.java:179) at weblogic.utils.classloaders.ChangeAwareClassLoader.loadClass(ChangeAwareClassLoader.java:35) at java.lang.ClassLoader.loadClassInternal(ClassLoader.java:319) at org.springframework.web.servlet.FrameworkServlet.processRequest(FrameworkServlet.java:683) at org.springframework.web.servlet.FrameworkServlet.doGet(FrameworkServlet.java:552) at javax.servlet.http.HttpServlet.service(HttpServlet.java:707) at javax.servlet.http.HttpServlet.service(HttpServlet.java:820) at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:226) at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:124) at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:283) at weblogic.servlet.internal.ServletStubImpl.onAddToMapException(ServletStubImpl.java:394) at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:309) at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:175) at weblogic.servlet.internal.RequestDispatcherImpl.invokeServlet(RequestDispatcherImpl.java:533) at weblogic.servlet.internal.RequestDispatcherImpl.forward(RequestDispatcherImpl.java:266) at org.springframework.web.servlet.mvc.ServletForwardingController.handleRequestInternal(ServletForwardingController.java:129) at org.springframework.web.servlet.mvc.AbstractController.handleRequest(AbstractController.java:153) at org.springframework.web.servlet.mvc.SimpleControllerHandlerAdapter.handle(SimpleControllerHandlerAdapter.java:48) at org.springframework.web.servlet.DispatcherServlet.doDispatch(DispatcherServlet.java:771) at org.springframework.web.servlet.DispatcherServlet.doService(DispatcherServlet.java:716) at org.springframework.web.servlet.FrameworkServlet.processRequest(FrameworkServlet.java:647) at org.springframework.web.servlet.FrameworkServlet.doGet(FrameworkServlet.java:552) at javax.servlet.http.HttpServlet.service(HttpServlet.java:707) at javax.servlet.http.HttpServlet.service(HttpServlet.java:820) ...

Read the article

Linq2SQL vs NHibernate performance (have I gone mad?)

- by HeavyWave

I have written the following tests to compare performance of Linq2SQL and NHibernate and I find results to be somewhat strange. Mappings are straight forward and identical for both. Both are running against a live DB. Although I'm not deleting Campaigns in case of Linq, but that shouldn't affect performance by more than 10 ms. Linq: [Test] public void Test1000ReadsWritesToAgentStateLinqPrecompiled() { Stopwatch sw = new Stopwatch(); Stopwatch swIn = new Stopwatch(); sw.Start(); for (int i = 0; i < 1000; i++) { swIn.Reset(); swIn.Start(); ReadWriteAndDeleteAgentStateWithLinqPrecompiled(); swIn.Stop(); Console.WriteLine("Run ReadWriteAndDeleteAgentState: " + swIn.ElapsedMilliseconds + " ms"); } sw.Stop(); Console.WriteLine("Total Time: " + sw.ElapsedMilliseconds + " ms"); Console.WriteLine("Average time to execute queries: " + sw.ElapsedMilliseconds / 1000 + " ms"); } private static readonly Func<AgentDesktop3DataContext, int, EntityModel.CampaignDetail> GetCampaignById = CompiledQuery.Compile<AgentDesktop3DataContext, int, EntityModel.CampaignDetail>( (ctx, sessionId) => (from cd in ctx.CampaignDetails join a in ctx.AgentCampaigns on cd.CampaignDetailId equals a.CampaignDetailId where a.AgentStateId == sessionId select cd).FirstOrDefault()); private void ReadWriteAndDeleteAgentStateWithLinqPrecompiled() { int id = 0; using (var ctx = new AgentDesktop3DataContext()) { EntityModel.AgentState agentState = new EntityModel.AgentState(); var campaign = new EntityModel.CampaignDetail { CampaignName = "Test" }; var campaignDisposition = new EntityModel.CampaignDisposition { Code = "123" }; campaignDisposition.Description = "abc"; campaign.CampaignDispositions.Add(campaignDisposition); agentState.CallState = 3; campaign.AgentCampaigns.Add(new AgentCampaign { AgentState = agentState }); ctx.CampaignDetails.InsertOnSubmit(campaign); ctx.AgentStates.InsertOnSubmit(agentState); ctx.SubmitChanges(); id = agentState.AgentStateId; } using (var ctx = new AgentDesktop3DataContext()) { var dbAgentState = ctx.GetAgentStateById(id); Assert.IsNotNull(dbAgentState); Assert.AreEqual(dbAgentState.CallState, 3); var campaignDetails = GetCampaignById(ctx, id); Assert.AreEqual(campaignDetails.CampaignDispositions[0].Description, "abc"); } using (var ctx = new AgentDesktop3DataContext()) { ctx.DeleteSessionById(id); } } NHibernate (the loop is the same): private void ReadWriteAndDeleteAgentState() { var id = WriteAgentState().Id; StartNewTransaction(); var dbAgentState = agentStateRepository.Get(id); Assert.IsNotNull(dbAgentState); Assert.AreEqual(dbAgentState.CallState, 3); Assert.AreEqual(dbAgentState.Campaigns[0].Dispositions[0].Description, "abc"); var campaignId = dbAgentState.Campaigns[0].Id; agentStateRepository.Delete(dbAgentState); NHibernateSession.Current.Transaction.Commit(); Cleanup(campaignId); NHibernateSession.Current.BeginTransaction(); } Results: NHibernate: Total Time: 9469 ms Average time to execute 13 queries: 9 ms Linq: Total Time: 127200 ms Average time to execute 13 queries: 127 ms Linq lost by 13.5 times! Event with precompiled queries (both read queries are precompiled). This can't be right, although I expected NHibernate to be faster, this is just too big of a difference, considering mappings are identical and NHibernate actually executes more queries against the DB.

Read the article

OpenVPN Server Ethernet Bridging Question

- by Hooplad

Hello All, I am having a difficult time properly configuring an ethernet bridge using OpenVPN 2.0.9 install on CentOS 5 ( VPN server ). The goal that I am trying to complete is to connect a VM ( instance running on the same CentOS machine ) acting as a Microsoft Business Contact Manager server. I would then like this "BCM server" to serve Windows XP clients on 192.168.1.0/24 network as well as clients connecting from VPN ( 10.8.0.0/24 ). The setup as it is now was based off a known working configuration. The problem with the working configuration was that it would allow to the client to connect and access everything running on the VPN server ( SVN, Samba, VM Server ) but not any computers on the 192.168.1.0/24 network. I must disclose that the VPN server is behind a router/firewall. Ports are being forwarded correctly ( again, clients were able to connect to the VPN server with no problem. netcat confirms the udp port is open as well ). current ifconfig output br0 Link encap:Ethernet HWaddr 00:21:5E:4D:3A:C2 inet addr:192.168.1.169 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::221:5eff:fe4d:3ac2/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:846890 errors:0 dropped:0 overruns:0 frame:0 TX packets:3072351 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:42686842 (40.7 MiB) TX bytes:4540654180 (4.2 GiB) eth0 Link encap:Ethernet HWaddr 00:21:5E:4D:3A:C2 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:882641 errors:0 dropped:0 overruns:0 frame:0 TX packets:1781383 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:82342803 (78.5 MiB) TX bytes:2614727660 (2.4 GiB) Interrupt:169 eth1 Link encap:Ethernet HWaddr 00:21:5E:4D:3A:C3 UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 RX packets:650 errors:0 dropped:0 overruns:0 frame:0 TX packets:1347223 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:67403 (65.8 KiB) TX bytes:1959529142 (1.8 GiB) Interrupt:233 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:17452058 errors:0 dropped:0 overruns:0 frame:0 TX packets:17452058 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:94020256229 (87.5 GiB) TX bytes:94020256229 (87.5 GiB) tap0 Link encap:Ethernet HWaddr DE:18:C6:D7:01:63 inet6 addr: fe80::dc18:c6ff:fed7:163/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3086 errors:0 dropped:166 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 b) TX bytes:315099 (307.7 KiB) vmnet1 Link encap:Ethernet HWaddr 00:50:56:C0:00:01 inet addr:192.168.177.1 Bcast:192.168.177.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fec0:1/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:4224 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) vmnet8 Link encap:Ethernet HWaddr 00:50:56:C0:00:08 inet addr:192.168.55.1 Bcast:192.168.55.255 Mask:255.255.255.0 inet6 addr: fe80::250:56ff:fec0:8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:4226 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) current route table Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.55.0 * 255.255.255.0 U 0 0 0 vmnet8 192.168.177.0 * 255.255.255.0 U 0 0 0 vmnet1 192.168.1.0 * 255.255.255.0 U 0 0 0 br0 current iptables output Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere Chain OUTPUT (policy ACCEPT) target prot opt source destination server_known_working.conf local banshee port 1194 proto udp dev tap0 ca ca.crt cert banshee_server.crt key banshee_server.key dh dh1024.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "route 192.168.1.0 255.255.255.0" client-to-client keepalive 10 120 tls-auth ta.key 0 user nobody group nobody persist-key persist-tun status openvpn-status.log verb 4 The following is the current CentOS server config file. server_ethernet_bridged.conf ( current ) local 192.168.1.169 port 1194 proto udp dev tap0 ca ca.crt cert server.crt key server.key dh dh1024.pem ifconfig-pool-persist ipp.txt server-bridge 192.168.1.169 255.255.255.0 192.168.1.200 192.168.1.210 push "route 192.168.1.0 255.255.255.0 192.168.1.1" client-to-client keepalive 10 120 tls-auth ta.key 0 user nobody group nobody persist-key persist-tun status openvpn-status.log verb 6 The following is one of the client's config file that was used with the known working configuration. client.opvn client dev tap proto udp remote XXX.XXX.XXX 1194 resolv-retry infinite nobind persist-key persist-tun ca client.crt cert client.crt key client.key tls-auth client.key 1 verb 3 I have tried the HOWTO provided by OpenVPN as well as others http://www.thebakershome.net/openvpn%5Ftutorial?page=1 with no success. Any help or suggestions would be appreciated.

Read the article

OpenVPN and PPTP on XEN VPS

- by amiv

I have Debian based system (Ubuntu 11.10) on XEN VPS. I've installed OpenVPN and works great. I need to install PPTP too, so did it and clients can connect, but they have no internet on client side. If I connect to VPN over PPTP I can ping and access to only my VPS by its IP, but ony that. There's no "internet" on client side. It looks it's not DNS problems (I'm using 8.8.8.8) because I can't ping known IPs. I bet the solution is simple, but don't have any idea. Any guess? /etc/pptpd.conf option /etc/ppp/pptpd-options logwtmp localip 46.38.xx.xx remoteip 10.1.0.1-10 /etc/ppp/pptpd-options name pptpd refuse-pap refuse-chap refuse-mschap require-mschap-v2 require-mppe-128 ms-dns 8.8.8.8 ms-dns 8.8.4.4 proxyarp nodefaultroute lock nobsdcomp /etc/ppp/ip-up [...] ifconfig ppp0 mtu 1400 /etc/sysctl.conf [...] net.ipv4.ip_forward=1 Command which I run: iptables -t nat -A POSTROUTING -j SNAT --to-source 46.38.xx.xx (IP of my VPS) The client can connect, first one gets IP 10.1.0.1 and DNS from Google. I bet it's iptables problem, am I right? I'm iptables noob and I don't have idea what's wrong. And here's the ifconfig and route command before client connect via PPTP: root@vps3780:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default xx.xx.tel.ru 0.0.0.0 UG 100 0 0 eth0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 46.38.xx.0 * 255.255.255.0 U 0 0 0 eth0 root@vps3780:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:16:3e:56:xx:xx inet addr:46.38.xx.xx Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::216:xx:xx:dfb6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:22671 errors:0 dropped:81 overruns:0 frame:0 TX packets:2266 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1813358 (1.8 MB) TX bytes:667626 (667.6 KB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:100 errors:0 dropped:0 overruns:0 frame:0 TX packets:100 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:10778 (10.7 KB) TX bytes:10778 (10.7 KB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:602 errors:0 dropped:0 overruns:0 frame:0 TX packets:612 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:90850 (90.8 KB) TX bytes:418904 (418.9 KB) And here's the ifconfig and route command after client connect via PPTP: root@vps3780:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default xx.xx.tel.ru 0.0.0.0 UG 100 0 0 eth0 10.1.0.1 * 255.255.255.255 UH 0 0 0 ppp0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 46.38.xx.0 * 255.255.255.0 U 0 0 0 eth0 root@vps3780:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:16:3e:56:xx:xx inet addr:46.38.xx.xx Bcast:0.0.0.0 Mask:255.255.255.0 inet6 addr: fe80::216:xx:xx:dfb6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:22989 errors:0 dropped:82 overruns:0 frame:0 TX packets:2352 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1841310 (1.8 MB) TX bytes:678456 (678.4 KB) Interrupt:24 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:112 errors:0 dropped:0 overruns:0 frame:0 TX packets:112 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:12102 (12.1 KB) TX bytes:12102 (12.1 KB) ppp0 Link encap:Point-to-Point Protocol inet addr:46.38.xx.xx P-t-P:10.1.0.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1400 Metric:1 RX packets:66 errors:0 dropped:0 overruns:0 frame:0 TX packets:15 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:10028 (10.0 KB) TX bytes:660 (660.0 B) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:602 errors:0 dropped:0 overruns:0 frame:0 TX packets:612 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:90850 (90.8 KB) TX bytes:418904 (418.9 KB) And ugly iptables --list output: root@vps3780:~# iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- 10.8.0.0/24 anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable ACCEPT all -- 10.1.0.0/24 anywhere ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- 10.1.0.0/24 anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT all -- 10.8.0.0/24 anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable And ugly iptables -t nat -L output: root@vps3780:~# iptables -t nat -L Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain INPUT (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination SNAT all -- 10.8.0.0/24 anywhere to:46.38.xx.xx MASQUERADE all -- 10.1.0.0/24 anywhere SNAT all -- 10.1.0.0/24 anywhere to:46.38.xx.xx SNAT all -- 10.8.0.0/24 anywhere to:46.38.xx.xx SNAT all -- 10.1.0.0/24 anywhere to:46.38.xx.xx MASQUERADE all -- anywhere anywhere SNAT all -- anywhere anywhere to:46.38.xx.xx SNAT all -- 10.8.0.0/24 anywhere to:46.38.xx.xx MASQUERADE all -- anywhere anywhere MASQUERADE all -- 10.1.0.0/24 anywhere MASQUERADE all -- anywhere anywhere MASQUERADE all -- 10.1.0.0/24 anywhere As I said - OpenVPN works very good. 10.8.0.0/24 for OpenVPN (on tun0). PPTP won't work. 10.1.0.0/24 for PPTP (on ppp0). Clients can connect, but they haven't "internet". Any suggestions will be appreciated. Second whole day fighting with no results. EDIT: iptables -t filter -F - it resolved my problem :-)

Read the article

A new method of supporting FOSS?

- by James

I have been kicking an idea around for sometime and wondered if something of it's nature hadn't already been invented. The premise is a website that integrates code management, project/team management, and micro-transactions. Donations, in and of themselves, are a sporadic, and unreliable method of supporting developers. Furthermore most free software that accepts donations is started by programmers ,be it to learn, because of a hobby, or because they saw a niche that needed to be filled. There is no method in place of of saying "hay, the FOSS community needs this kind of software, will someone develop it, and accept donations!?" Programmers should be programming, not busy begging for money. Basically the idea is people can go to the site in question, and start a project or make a request. Anyone signed up with the site can start a request. Each member account is free to support or "upvote" a project request. Requests and the associated number of votes let programmers in the community know the needs of the community. When a project is started a request for developers can be put forth. Developers have a ranking based on commits to other projects. The project founder can send invites to known Developers, or accept invites from members based on developer ranking. Once the project has at least one team-member, an objectives sheet or "draft" can be put out, listing design, goals, and features. The founding member and each team-member may contribute to this sheet. Each "milestone", or "Feature" is represented by an article. An article is any unit of a draft that can be voted on by The Project Founder, Team-members, and contributors...which brings me to the next half of this idea. --Microtransactions-- People signed up with this hypothetical website can purchase credits which then can be transfered to projects they would like to support. Anyone who transfers credits to a project is known as a contributor to that project. At anytime a Founder, or the lead team-member may submit an article, or a design (multiple articles) for consideration. All team-members, as well as the Founder, can vote once for each article freely. Contributors may vote yes or no on a number of articles (independent of any given meeting where a particular design or article is considered) equal to the number of credits they have placed into a contributors fund for that particular project. A contributors fund is a proxy between a sites credit account, and a projects credit account. It is sort of like a promise to contribute, instead of an actual contribution. Contributers may place constraints on particular articles such that if those constraints (a yes or no vote) are satisfied then a manually specified amount of credits is automatically transfered to the project account. This allows a project to develop based on the needs of those who may (in the future) financially rely on the project. --- Code commits & milestones --- When a team-member makes a commit, they may specify if it's a minor commit, a bug fix, a compatibility patch (i.e. for a new platform), or a milestone (an article voted on previously). People signed up with the website, may download the updated project and test it to see if the programmer's assertion is true about the commit. A report may then be filed on a small form, giving a one or two paragraphs, and a positive or negative confirmation of the programmer's goal for that particular commit. After all milestones for a particular draft are complete, a new draft is submitted for voting. Also funds may withdrawn by each team-member based on the proportion of commits and milestones confirmed (fulfilled the stated purpose) for each programmer. --- voting --- Members, contributor, and non-contributor, may make priority requests for particular articles of a draft. The project founder may or may not opt to fill those requests based on the volume of upvotes. A fulfilled priority request means that any team-member that makes a community-confirmed commit for an article is, when all articles for the draft are fulfilled, granted a portion of project credits in proportion to the average priority of all the articles he committed. ---- Notes --- While this is horribly prone to design-by-committee the one saving grace is that the lead team-member may place constraints on a draft such that some, or ALL articles must be voted yes. Commits may not begin until a draft satisfying said constraints is approved. What does SO think, is this idea feasible? Does anyone see major problems with this? Is there any insights, or improvements that could be made?

Read the article

Packets marked by iptables only sent to the correct routing table sometimes

- by cookiecaper

I am trying to route packets generated by a specific user out over a VPN. I have this configuration: $ sudo iptables -S -t nat -P PREROUTING ACCEPT -P OUTPUT ACCEPT -P POSTROUTING ACCEPT -A POSTROUTING -o tun0 -j MASQUERADE $ sudo iptables -S -t mangle -P PREROUTING ACCEPT -P INPUT ACCEPT -P FORWARD ACCEPT -P OUTPUT ACCEPT -P POSTROUTING ACCEPT -A OUTPUT -m owner --uid-owner guy -j MARK --set-xmark 0xb/0xffffffff $ sudo ip rule show 0: from all lookup local 32765: from all fwmark 0xb lookup 11 32766: from all lookup main 32767: from all lookup default $ sudo ip route show table 11 10.8.0.5 dev tun0 proto kernel scope link src 10.8.0.6 10.8.0.6 dev tun0 scope link 10.8.0.1 via 10.8.0.5 dev tun0 0.0.0.0/1 via 10.8.0.5 dev tun0 $ sudo iptables -S -t raw -P PREROUTING ACCEPT -P OUTPUT ACCEPT -A OUTPUT -m owner --uid-owner guy -j TRACE -A OUTPUT -p tcp -m tcp --dport 80 -j TRACE It seems that some sites work fine and use the VPN, but others don't and fall back to the normal interface. This is bad. This is a packet trace that used VPN: Oct 27 00:24:28 agent kernel: [612979.976052] TRACE: raw:OUTPUT:rule:2 IN= OUT=eth0 SRC=XXX.YYY.ZZZ.AAA DST=23.1.17.194 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=14494 DF PROTO=TCP SPT=57502 DPT=80 SEQ=2294732931 ACK=0 WINDOW=5840 RES=0x00 SYN URGP=0 OPT (020405B40402080A03A6E01D0000000001030307) UID=999 GID=999 Oct 27 00:24:28 agent kernel: [612979.976105] TRACE: raw:OUTPUT:policy:3 IN= OUT=eth0 SRC=XXX.YYY.ZZZ.AAA DST=23.1.17.194 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=14494 DF PROTO=TCP SPT=57502 DPT=80 SEQ=2294732931 ACK=0 WINDOW=5840 RES=0x00 SYN URGP=0 OPT (020405B40402080A03A6E01D0000000001030307) UID=999 GID=999 Oct 27 00:24:28 agent kernel: [612979.976164] TRACE: mangle:OUTPUT:rule:1 IN= OUT=eth0 SRC=XXX.YYY.ZZZ.AAA DST=23.1.17.194 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=14494 DF PROTO=TCP SPT=57502 DPT=80 SEQ=2294732931 ACK=0 WINDOW=5840 RES=0x00 SYN URGP=0 OPT (020405B40402080A03A6E01D0000000001030307) UID=999 GID=999 Oct 27 00:24:28 agent kernel: [612979.976210] TRACE: mangle:OUTPUT:policy:2 IN= OUT=eth0 SRC=XXX.YYY.ZZZ.AAA DST=23.1.17.194 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=14494 DF PROTO=TCP SPT=57502 DPT=80 SEQ=2294732931 ACK=0 WINDOW=5840 RES=0x00 SYN URGP=0 OPT (020405B40402080A03A6E01D0000000001030307) UID=999 GID=999 MARK=0xb Oct 27 00:24:28 agent kernel: [612979.976269] TRACE: nat:OUTPUT:policy:1 IN= OUT=eth0 SRC=XXX.YYY.ZZZ.AAA DST=23.1.17.194 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=14494 DF PROTO=TCP SPT=57502 DPT=80 SEQ=2294732931 ACK=0 WINDOW=5840 RES=0x00 SYN URGP=0 OPT (020405B40402080A03A6E01D0000000001030307) UID=999 GID=999 MARK=0xb Oct 27 00:24:28 agent kernel: [612979.976320] TRACE: filter:OUTPUT:policy:1 IN= OUT=eth0 SRC=XXX.YYY.ZZZ.AAA DST=23.1.17.194 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=14494 DF PROTO=TCP SPT=57502 DPT=80 SEQ=2294732931 ACK=0 WINDOW=5840 RES=0x00 SYN URGP=0 OPT (020405B40402080A03A6E01D0000000001030307) UID=999 GID=999 MARK=0xb Oct 27 00:24:28 agent kernel: [612979.976367] TRACE: mangle:POSTROUTING:policy:1 IN= OUT=tun0 SRC=XXX.YYY.ZZZ.AAA DST=23.1.17.194 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=14494 DF PROTO=TCP SPT=57502 DPT=80 SEQ=2294732931 ACK=0 WINDOW=5840 RES=0x00 SYN URGP=0 OPT (020405B40402080A03A6E01D0000000001030307) UID=999 GID=999 MARK=0xb Oct 27 00:24:28 agent kernel: [612979.976414] TRACE: nat:POSTROUTING:rule:1 IN= OUT=tun0 SRC=XXX.YYY.ZZZ.AAA DST=23.1.17.194 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=14494 DF PROTO=TCP SPT=57502 DPT=80 SEQ=2294732931 ACK=0 WINDOW=5840 RES=0x00 SYN URGP=0 OPT (020405B40402080A03A6E01D0000000001030307) UID=999 GID=999 MARK=0xb and this is one that didn't: Oct 27 00:22:41 agent kernel: [612873.662559] TRACE: raw:OUTPUT:rule:2 IN= OUT=eth0 SRC=XXX.YYY.ZZZ.AAA DST=209.68.27.16 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=40425 DF PROTO=TCP SPT=45305 DPT=80 SEQ=604973951 ACK=0 WINDOW=5840 RES=0x00 SYN URGP=0 OPT (020405B40402080A03A6B6960000000001030307) UID=999 GID=999 Oct 27 00:22:41 agent kernel: [612873.662609] TRACE: raw:OUTPUT:policy:3 IN= OUT=eth0 SRC=XXX.YYY.ZZZ.AAA DST=209.68.27.16 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=40425 DF PROTO=TCP SPT=45305 DPT=80 SEQ=604973951 ACK=0 WINDOW=5840 RES=0x00 SYN URGP=0 OPT (020405B40402080A03A6B6960000000001030307) UID=999 GID=999 Oct 27 00:22:41 agent kernel: [612873.662664] TRACE: mangle:OUTPUT:rule:1 IN= OUT=eth0 SRC=XXX.YYY.ZZZ.AAA DST=209.68.27.16 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=40425 DF PROTO=TCP SPT=45305 DPT=80 SEQ=604973951 ACK=0 WINDOW=5840 RES=0x00 SYN URGP=0 OPT (020405B40402080A03A6B6960000000001030307) UID=999 GID=999 Oct 27 00:22:41 agent kernel: [612873.662709] TRACE: mangle:OUTPUT:policy:2 IN= OUT=eth0 SRC=XXX.YYY.ZZZ.AAA DST=209.68.27.16 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=40425 DF PROTO=TCP SPT=45305 DPT=80 SEQ=604973951 ACK=0 WINDOW=5840 RES=0x00 SYN URGP=0 OPT (020405B40402080A03A6B6960000000001030307) UID=999 GID=999 MARK=0xb Oct 27 00:22:41 agent kernel: [612873.662761] TRACE: nat:OUTPUT:policy:1 IN= OUT=eth0 SRC=XXX.YYY.ZZZ.AAA DST=209.68.27.16 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=40425 DF PROTO=TCP SPT=45305 DPT=80 SEQ=604973951 ACK=0 WINDOW=5840 RES=0x00 SYN URGP=0 OPT (020405B40402080A03A6B6960000000001030307) UID=999 GID=999 MARK=0xb Oct 27 00:22:41 agent kernel: [612873.662808] TRACE: filter:OUTPUT:policy:1 IN= OUT=eth0 SRC=XXX.YYY.ZZZ.AAA DST=209.68.27.16 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=40425 DF PROTO=TCP SPT=45305 DPT=80 SEQ=604973951 ACK=0 WINDOW=5840 RES=0x00 SYN URGP=0 OPT (020405B40402080A03A6B6960000000001030307) UID=999 GID=999 MARK=0xb Oct 27 00:22:41 agent kernel: [612873.662855] TRACE: mangle:POSTROUTING:policy:1 IN= OUT=eth0 SRC=XXX.YYY.ZZZ.AAA DST=209.68.27.16 LEN=60 TOS=0x00 PREC=0x00 TTL=64 ID=40425 DF PROTO=TCP SPT=45305 DPT=80 SEQ=604973951 ACK=0 WINDOW=5840 RES=0x00 SYN URGP=0 OPT (020405B40402080A03A6B6960000000001030307) UID=999 GID=999 MARK=0xb I have already tried "ip route flush cache", to no avail. I do not know why the first packet goes through the correct routing table, and the second doesn't. Both are marked. Once again, I do not want ALL packets system-wide to go through the VPN, I only want packets from a specific user (UID=999) to go through the VPN. I am testing ipchicken.com and walmart.com via links, from the same user, same shell. walmart.com appears to use the VPN; ipchicken.com does not. Any help appreciated. Will send 0.5 bitcoins to answerer who makes this fixed.

Read the article

rsync over ssh is not working anymore, while ssh itself is working fine (Write failed: broken pipe)

- by brazorf

This issue started happening after i changed router. This is the scenario: Windows7 Host Ubuntu 10.04 Guest (VirtualBox) Ubuntu 10.04 remote server What i used to do is run a very basic rsync command: rsync -avz --delete /local/path/ username@host:/path/to/remote/directory This worked perfect until i did change adsl provider, and i changed router aswell: now, this happens: rsync on Ubuntu Guest is not working anymore (to any random server), if using this new router rsync on Ubuntu Guest is WORKING, if i switch back to old router i tried a new virtual box ubuntu install, and the command is WORKING with both the routers So, the not-working-combo is oldUbuntu + newRouter. To get things worst, i can state that (on the not-working ubuntu) i ping the remote host plain ssh connection to the remote host is working fine (i can auth, connect, and do stuff on the remote host) scp is NOT working (this is just a further thing i tried) This is the console output of the execution, with ssh verbose set to vvvv: root@client:~# rsync -ae 'ssh -vvvv' /root/test-rsync/ {username}@{hostname}:/home/{username}/test/ OpenSSH_5.3p1 Debian-3ubuntu7, OpenSSL 0.9.8k 25 Mar 2009 debug1: Reading configuration data /root/.ssh/config debug1: Applying options for {hostname} debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to {hostname} [{ip.add.re.ss}] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug3: Not a RSA1 key file /root/.ssh/{private_key}. debug2: key_type_from_name: unknown key type '-----BEGIN' debug3: key_read: missing keytype debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug3: key_read: missing whitespace debug2: key_type_from_name: unknown key type '-----END' debug3: key_read: missing keytype debug1: identity file /root/.ssh/{private_key} type 1 debug1: Checking blacklist file /usr/share/ssh/blacklist.RSA-2048 debug1: Checking blacklist file /etc/ssh/blacklist.RSA-2048 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3p1 Debian-3ubuntu7 debug1: match: OpenSSH_5.3p1 Debian-3ubuntu7 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.3p1 Debian-3ubuntu7 debug2: fd 3 setting O_NONBLOCK debug1: SSH2_MSG_KEXINIT sent debug3: Wrote 792 bytes for a total of 831 debug1: SSH2_MSG_KEXINIT received debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: [email protected],zlib,none debug2: kex_parse_kexinit: [email protected],zlib,none debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: kex_parse_kexinit: diffie-hellman-group-exchange-sha256,diffie-hellman-group-exchange-sha1,diffie-hellman-group14-sha1,diffie-hellman-group1-sha1 debug2: kex_parse_kexinit: ssh-rsa,ssh-dss debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: aes128-ctr,aes192-ctr,aes256-ctr,arcfour256,arcfour128,aes128-cbc,3des-cbc,blowfish-cbc,cast128-cbc,aes192-cbc,aes256-cbc,arcfour,[email protected] debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: hmac-md5,hmac-sha1,[email protected],hmac-ripemd160,[email protected],hmac-sha1-96,hmac-md5-96 debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: none,[email protected] debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: debug2: kex_parse_kexinit: first_kex_follows 0 debug2: kex_parse_kexinit: reserved 0 debug2: mac_setup: found hmac-md5 debug1: kex: server->client aes128-ctr hmac-md5 [email protected] debug2: mac_setup: found hmac-md5 debug1: kex: client->server aes128-ctr hmac-md5 [email protected] debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug3: Wrote 24 bytes for a total of 855 debug2: dh_gen_key: priv key bits set: 125/256 debug2: bits set: 525/1024 debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug3: Wrote 144 bytes for a total of 999 debug3: check_host_in_hostfile: filename /root/.ssh/known_hosts debug3: check_host_in_hostfile: match line 4 debug3: check_host_in_hostfile: filename /root/.ssh/known_hosts debug3: check_host_in_hostfile: match line 5 debug1: Host '{hostname}' is known and matches the RSA host key. debug1: Found key in /root/.ssh/known_hosts:4 debug2: bits set: 512/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug3: Wrote 16 bytes for a total of 1015 debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug3: Wrote 48 bytes for a total of 1063 debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /root/.ssh/{private_key} (0x7f3ad0e7f9b0) debug3: Wrote 80 bytes for a total of 1143 debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,gssapi,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering public key: /root/.ssh/{private_key} debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug3: Wrote 368 bytes for a total of 1511 debug1: Server accepts key: pkalg ssh-rsa blen 277 debug2: input_userauth_pk_ok: fp 1b:65:36:92:59:b3:12:3e:8c:c6:03:28:d4:81:09:dc debug3: sign_and_send_pubkey debug1: read PEM private key done: type RSA debug3: Wrote 656 bytes for a total of 2167 debug1: Enabling compression at level 6. debug1: Authentication succeeded (publickey). debug2: fd 4 setting O_NONBLOCK debug3: fd 5 is O_NONBLOCK debug1: channel 0: new [client-session] debug3: ssh_session2_open: channel_new: 0 debug2: channel 0: send open debug1: Requesting [email protected] debug1: Entering interactive session. debug3: Wrote 112 bytes for a total of 2279 debug2: callback start debug2: client_session2_setup: id 0 debug1: Sending environment. debug3: Ignored env TERM debug3: Ignored env SHELL debug3: Ignored env SSH_CLIENT debug3: Ignored env SSH_TTY debug1: Sending env LC_ALL = en_US.UTF-8 debug2: channel 0: request env confirm 0 debug3: Ignored env USER debug3: Ignored env LS_COLORS debug3: Ignored env MAIL debug3: Ignored env PATH debug3: Ignored env PWD debug1: Sending env LANG = en_US.UTF-8 debug2: channel 0: request env confirm 0 debug3: Ignored env SHLVL debug3: Ignored env HOME debug3: Ignored env LANGUAGE debug3: Ignored env LOGNAME debug3: Ignored env SSH_CONNECTION debug3: Ignored env LESSOPEN debug3: Ignored env LESSCLOSE debug3: Ignored env _ debug1: Sending command: rsync --server -logDtpre.iLsf . /home/{username}/test/ debug2: channel 0: request exec confirm 1 debug2: fd 3 setting TCP_NODELAY debug2: callback done debug2: channel 0: open confirm rwindow 0 rmax 32768 debug3: Wrote 208 bytes for a total of 2487 At this point everything freeze for lots of minutes, ending in Write failed: Broken pipe rsync: connection unexpectedly closed (0 bytes received so far) [sender] rsync error: unexplained error (code 255) at io.c(601) [sender=3.0.7] Any suggestion? Thank You F. Edit 2012/09/13: i am changing title and issue definition, since i made some TINY step ahead and i think i can give more detailed clues.

Read the article

What are good CLI tools for JSON?

- by jasonmp85

General Problem Though I may be diagnosing the root cause of an event, determining how many users it affected, or distilling timing logs in order to assess the performance and throughput impact of a recent code change, my tools stay the same: grep, awk, sed, tr, uniq, sort, zcat, tail, head, join, and split. To glue them all together, Unix gives us pipes, and for fancier filtering we have xargs. If these fail me, there's always perl -e. These tools are perfect for processing CSV files, tab-delimited files, log files with a predictable line format, or files with comma-separated key-value pairs. In other words, files where each line has next to no context. XML Analogues I recently needed to trawl through Gigabytes of XML to build a histogram of usage by user. This was easy enough with the tools I had, but for more complicated queries the normal approaches break down. Say I have files with items like this: <foo user="me"> <baz key="zoidberg" value="squid" /> <baz key="leela" value="cyclops" /> <baz key="fry" value="rube" /> </foo> And let's say I want to produce a mapping from user to average number of <baz>s per <foo>. Processing line-by-line is no longer an option: I need to know which user's <foo> I'm currently inspecting so I know whose average to update. Any sort of Unix one liner that accomplishes this task is likely to be inscrutable. Fortunately in XML-land, we have wonderful technologies like XPath, XQuery, and XSLT to help us. Previously, I had gotten accustomed to using the wonderful XML::XPath Perl module to accomplish queries like the one above, but after finding a TextMate Plugin that could run an XPath expression against my current window, I stopped writing one-off Perl scripts to query XML. And I just found out about XMLStarlet which is installing as I type this and which I look forward to using in the future. JSON Solutions? So this leads me to my question: are there any tools like this for JSON? It's only a matter of time before some investigation task requires me to do similar queries on JSON files, and without tools like XPath and XSLT, such a task will be a lot harder. If I had a bunch of JSON that looked like this: { "firstName": "Bender", "lastName": "Robot", "age": 200, "address": { "streetAddress": "123", "city": "New York", "state": "NY", "postalCode": "1729" }, "phoneNumber": [ { "type": "home", "number": "666 555-1234" }, { "type": "fax", "number": "666 555-4567" } ] } And wanted to find the average number of phone numbers each person had, I could do something like this with XPath: fn:avg(/fn:count(phoneNumber)) Questions Are there any command-line tools that can "query" JSON files in this way? If you have to process a bunch of JSON files on a Unix command line, what tools do you use? Heck, is there even work being done to make a query language like this for JSON? If you do use tools like this in your day-to-day work, what do you like/dislike about them? Are there any gotchas? I'm noticing more and more data serialization is being done using JSON, so processing tools like this will be crucial when analyzing large data dumps in the future. Language libraries for JSON are very strong and it's easy enough to write scripts to do this sort of processing, but to really let people play around with the data shell tools are needed. Related Questions Grep and Sed Equivalent for XML Command Line Processing Is there a query language for JSON? JSONPath or other XPath like utility for JSON/Javascript; or Jquery JSON

Read the article

Where do I start ?

- by Panthe

Brief History: Just graduated high school, learned a bit of python and C++, have no friends with any helpful computer knowledge at all. Out of anyone i met in my school years I was probably the biggest nerd, but no one really knew. I consider my self to have a vast amount of knowledge on computers and tech then the average person. built/fixed tons of computers, and ability to troubleshoot pretty much any problem I came across. Now that high school is over, Ive really been thinking about my career. Loving, living computers for the past 15 years of my life I decided to take my ability's and try to learn computer programming, why I didn't start earlier I don't know, seems to be big mistake on my part... Doing some research I concluded that Python was the first programming language I should learn, since it was high level and easier to understand then C++ and Java. I also knew that to become good at what I did I needed to know more then just 2 or 3 languages, which didn't seem like a big problem considering once I learned the way Python worked, mainly syntax changed, and the rest would come naturally. I watched a couple of youtube videos, downloaded some book pdf's and snooped around from some tutorials here and there to get the hang of what to do. A two solid weeks had passed of trying to understand the syntax, create small programs that used the basic functions and understanding how it worked, I think i have got the hang of it. It breaks down into what ive been dealing with all this time (although i kinda knew) is that, input,output, loops, functions and other things derived from 0's and 1's storing data and recalling it, ect. (A VERY BASIC IDEA). Ive been able to create small programs, Hangman, file storing, temperature conversion, Caeser Cipher decode/encoding, Fibonacci Sequence and more, which i can create and understand how each work. Being 2 weeks into this, I have learned alot. Nothing at all compared to what i should be learning in the years to come if i get a grip on what I'm doing. While doing these programs I wont stop untill I've done doing a practice problem on a book, which embarresing enough will take me a couple hour depending on the complexity of it. I absolutly will not put aside the challenge until its complete, WHICH CAN BE EXTREMELY DRAINING, ive tried most problems without cheating and reached success, which makes me feel extremely proud of my self after completing something after much trial and error. After all this I have met the demon, alogrithm's which seem to be key to effiecent code. I cant seem to rap my head around some of the computer codes people put out there using numbers, and sometimes even basic functions, I have been able to understand them after a while but i know there are alot more complex things to come, considering my self smart, functions that require complex codes, actually hurt my brain. NOTHING EVER IN LIFE HURT MY BRAIN....... not even math classes in highschool, trying to understand some of the stuff people put out there makes me feel like i have a mental disadvantage lol... i still walk forward though, crossing my fingers that the understanding will come with time. Sorry if is this is long i just wish someone takes all these things into consideration when answering my question. even through all these downsides im still pushing through and continuing to try and get good at this, i know reading these tutorials wont make me any good unless i can become creative and make my own, understand other peoples programs, so this leads me to the simple question i could have asked in the beginning..... WHERE IN THE WORLD DO I START ? Ive been trying to find out how to understand some of the open source projects, how i can work with experianced coders to learn from them and help them, but i dont think thats even possible by the way how far people's knowledge is compared to me, i have no freinds who i can learn from, can someone help me and guide me into the right direction.. i have a huge motivation to get good at coding, anything information would be extremely helpful

Read the article

MySQL: Creating table with FK error (errno 150)

- by Peter Bailey

I've tried searching on this error and nothing I've found helps me, so I apologize in advance if this is a duplicate and I'm just too dumb to find it. I've created a model with MySQL Workbench and am now attempting to install it to a mysql server. Using File Export Forward Engineer SQL CREATE Script... it outputs a nice big file for me, with all the settings I ask for. I switch over to MySQL GUI Tools (the Query Browser specifically) and load up this script (note that I'm going form one official MySQL tool to another). However, when I try to actually execute this file, I get the same error over and over SQLSTATE[HY000]: General error: 1005 Can't create table './srs_dev/location.frm' (errno: 150) "OK", I say to myself, something is wrong with the location table. So I check out the definition in the output file. SET @OLD_UNIQUE_CHECKS=@@UNIQUE_CHECKS, UNIQUE_CHECKS=0; SET @OLD_FOREIGN_KEY_CHECKS=@@FOREIGN_KEY_CHECKS, FOREIGN_KEY_CHECKS=0; SET @OLD_SQL_MODE=@@SQL_MODE, SQL_MODE='TRADITIONAL'; -- ----------------------------------------------------- -- Table `state` -- ----------------------------------------------------- DROP TABLE IF EXISTS `state` ; CREATE TABLE IF NOT EXISTS `state` ( `state_id` INT NOT NULL AUTO_INCREMENT , `iso_3166_2_code` VARCHAR(2) NOT NULL , `name` VARCHAR(60) NOT NULL , PRIMARY KEY (`state_id`) ) ENGINE = InnoDB; -- ----------------------------------------------------- -- Table `brand` -- ----------------------------------------------------- DROP TABLE IF EXISTS `brand` ; CREATE TABLE IF NOT EXISTS `brand` ( `brand_id` INT UNSIGNED NOT NULL AUTO_INCREMENT , `name` VARCHAR(45) NOT NULL , `domain` VARCHAR(45) NOT NULL , `manager_name` VARCHAR(100) NULL , `manager_email` VARCHAR(255) NULL , PRIMARY KEY (`brand_id`) ) ENGINE = InnoDB; -- ----------------------------------------------------- -- Table `location` -- ----------------------------------------------------- DROP TABLE IF EXISTS `location` ; CREATE TABLE IF NOT EXISTS `location` ( `location_id` INT UNSIGNED NOT NULL AUTO_INCREMENT , `name` VARCHAR(255) NOT NULL , `address_line_1` VARCHAR(255) NULL , `address_line_2` VARCHAR(255) NULL , `city` VARCHAR(100) NULL , `state_id` TINYINT UNSIGNED NULL DEFAULT NULL , `postal_code` VARCHAR(10) NULL , `phone_number` VARCHAR(20) NULL , `fax_number` VARCHAR(20) NULL , `lat` DECIMAL(9,6) NOT NULL , `lng` DECIMAL(9,6) NOT NULL , `contact_url` VARCHAR(255) NULL , `brand_id` TINYINT UNSIGNED NOT NULL , `summer_hours` VARCHAR(255) NULL , `winter_hours` VARCHAR(255) NULL , `after_hours_emergency` VARCHAR(255) NULL , `image_file_name` VARCHAR(100) NULL , `manager_name` VARCHAR(100) NULL , `manager_email` VARCHAR(255) NULL , `created_date` TIMESTAMP NOT NULL DEFAULT CURRENT_TIMESTAMP , PRIMARY KEY (`location_id`) , CONSTRAINT `fk_location_state` FOREIGN KEY (`state_id` ) REFERENCES `state` (`state_id` ) ON DELETE NO ACTION ON UPDATE NO ACTION, CONSTRAINT `fk_location_brand` FOREIGN KEY (`brand_id` ) REFERENCES `brand` (`brand_id` ) ON DELETE NO ACTION ON UPDATE NO ACTION) ENGINE = InnoDB; CREATE INDEX `fk_location_state` ON `location` (`state_id` ASC) ; CREATE INDEX `fk_location_brand` ON `location` (`brand_id` ASC) ; CREATE INDEX `idx_lat` ON `location` (`lat` ASC) ; CREATE INDEX `idx_lng` ON `location` (`lng` ASC) ; Looks ok to me. I surmise that maybe something is wrong with the Query Browser, so I put this file on the server and try to load it this way ] mysql -u admin -p -D dbname < path/to/create_file.sql And I get the same error. So I start to Google this issue and find all kinds of accounts that talk about an error with InnoDB style tables that fail with foreign keys, and the fix is to add "SET FOREIGN_KEY_CHECKS=0;" to the SQL script. Well, as you can see, that's already part of the file that MySQL Workbench spat out. So, my question is then, why is this not working when I'm doing what I think I'm supposed to be doing? Version Info: # MySQL: 5.0.45 GUI Tools: 1.2.17 Workbench: 5.0.30

Read the article

slow DNS resolution

- by Ehsan

I have a DNS server that resolves all queries for an internal group of servers. It is a bind on CentOS 5.5 (same as RHEL5) and I have set it up to allow recursion and resolve direction without any forwarders. The problem I am facing is that it takes a freakishly long amount of time to resolve a name for the first time. (in the magnitudes of 20 sec) This causes clients to give timeout. When I set it to forward all to Google's public DNS, i.e. 8.8.8.8+8.8.4.4, it works very nicely (within a second). I tried monitoring the traffic on the net to see why it is doing this: [root@ns1 ~]# tcpdump -nnvvvA -s0 udp tcpdump: listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 23:06:36.137797 IP (tos 0x0, ttl 64, id 35903, offset 0, flags [none], proto: UDP (17), length: 60) 172.17.1.10.36942 > 172.17.1.4.53: [udp sum ok] 19773+ A? www.paypal.com. (32) E..<[email protected]... .....N.5.(6.M=...........www.paypal.com..... 23:06:36.140594 IP (tos 0x0, ttl 64, id 56477, offset 0, flags [none], proto: UDP (17), length: 71) 172.17.1.4.6128 > 192.35.51.30.53: [udp sum ok] 10105 [1au] A? www.paypal.com. ar: . OPT UDPsize=4096 (43) E..G....@........#3....5.3fR'y...........www.paypal.com.......)........ 23:06:38.149756 IP (tos 0x0, ttl 64, id 13078, offset 0, flags [none], proto: UDP (17), length: 71) 172.17.1.4.52425 > 192.54.112.30.53: [udp sum ok] 54892 [1au] A? www.paypal.com. ar: . OPT UDPsize=4096 (43) [email protected]&.....6p....5.3.q.l...........www.paypal.com.......)........ 23:06:40.159725 IP (tos 0x0, ttl 64, id 43016, offset 0, flags [none], proto: UDP (17), length: 71) 172.17.1.4.24059 > 192.42.93.30.53: [udp sum ok] 11205 [1au] A? www.paypal.com. ar: . OPT UDPsize=4096 (43) E..G....@..@.....*].]..5.3..+............www.paypal.com.......)........ 23:06:41.141403 IP (tos 0x0, ttl 64, id 35904, offset 0, flags [none], proto: UDP (17), length: 60) 172.17.1.10.36942 > 172.17.1.4.53: [udp sum ok] 19773+ A? www.paypal.com. (32) E..<.@..@..@... .....N.5.(6.M=...........www.paypal.com..... 23:06:42.169652 IP (tos 0x0, ttl 64, id 44001, offset 0, flags [none], proto: UDP (17), length: 60) 172.17.1.4.9141 > 192.55.83.30.53: [udp sum ok] 1184 A? www.paypal.com. (32) E..<[email protected].#..5.(...............www.paypal.com..... 23:06:42.207295 IP (tos 0x0, ttl 54, id 38004, offset 0, flags [none], proto: UDP (17), length: 205) 192.55.83.30.53 > 172.17.1.4.9141: [udp sum ok] 1184- q: A? www.paypal.com. 0/3/3 ns: paypal.com. NS ns1.isc-sns.net., paypal.com. NS ns2.isc-sns.com., paypal.com. NS ns3.isc-sns.info. ar: ns1.isc-sns.net. AAAA 2001:470:1a::1, ns1.isc-sns.net. A 72.52.71.1, ns2.isc-sns.com. A 38.103.2.1 (177) E....t..6./A.7S......5#..................www.paypal.com..................ns1.isc-sns.net..............ns2.isc-sns...............ns3.isc-sns.info..,.......... ..p.............,..........H4G..I..........&g.. (this goes on for a few more seconds) If you look carefully, you will see that the first 3-4 root servers did not respond at all. This wastes 7-8 seconds, until one of them responded. Do you think I have setup something wrong here? Interestingly, when I dig directly from the root servers that did not respond, the always respond very fast (showing the firewall/nat is not the issue here). E.g. dig www.paypal.com @192.35.51.30 works perfectly, consistently, and very fast. What do you think about this mystery?

Read the article

PHP MVC Framework Structure

- by bigstylee

I am sorry about the amount of code here. I have tried to show enough for understanding while avoiding confusion (I hope). I have included a second copy of the code at Pastebin. (The code does execute without error/notice/warning.) I am currently creating a Content Management System while trying to implement the idea of Model View Controller. I have only recently come across the concept of MVC (within the last week) and trying to implement this into my current project. One of the features of the CMS is dynamic/customisable menu areas and each feature will be represented by a controller. Therefore there will be multiple versions of the Controller Class, each with specific extended functionality. I have looked at a number of tutorials and read some open source solutions to the MVC Framework. I am now trying to create a lightweight solution for my specific requirements. I am not interested in backwards compatibility, I am using PHP 5.3. An advantage of the Base class is not having to use global and can directly access any loaded class using $this->Obj['ClassName']->property/function();. Hoping to get some feedback using the basic structure outlined (with performance in mind). Specifically; a) Have I understood/implemented the concept of MVC correctly? b) Have I understood/implemented Object Orientated techniques with PHP 5 correctly? c) Should the class propertise of Base be static? d) Improvements? Thank you very much in advance! <?php /* A "Super Class" that creates/stores all object instances */ class Base { public static $Obj = array(); // Not sure this is the correct use of the "static" keyword? public static $var; static public function load_class($directory, $class) { echo count(self::$Obj)."\n"; // This does show the array is getting updated and not creating a new array :) if (!isset(self::$Obj[$class]) && !is_object(self::$Obj[$class])) //dont want to load it twice { /* Locate and include the class file based upon name ($class) */ return self::$Obj[$class] = new $class(); } return TRUE; } } /* Loads general configuration objects into the "Super Class" */ class Libraries extends Base { public function __construct(){ $this->load_class('library', 'Database'); $this->load_class('library', 'Session'); self::$var = 'Hello World!'; //testing visibility /* Other general funciton classes */ } } class Database extends Base { /* Connects to the the database and executes all queries */ public function query(){} } class Session extends Base { /* Implements Sessions in database (read/write) */ } /* General functionality of controllers */ abstract class Controller extends Base { protected function load_model($class, $method) { /* Locate and include the model file */ $this->load_class('model', $class); call_user_func(array(self::$Obj[$class], $method)); } protected function load_view($name) { /* Locate and include the view file */ #include('views/'.$name.'.php'); } } abstract class View extends Base { /* ... */ } abstract class Model extends Base { /* ... */ } class News extends Controller { public function index() { /* Displays the 5 most recent News articles and displays with Content Area */ $this->load_model('NewsModel', 'index'); $this->load_view('news', 'index'); echo $this->var; } public function menu() { /* Displays the News Title of the 5 most recent News articles and displays within the Menu Area */ $this->load_model('news/index'); $this->load_view('news/index'); } } class ChatBox extends Controller { /* ... */ } /* Lots of different features extending the controller/view/model class depending upon request and layout */ class NewsModel extends Model { public function index() { echo $this->var; self::$Obj['Database']->query(/*SELECT 5 most recent news articles*/); } public function menu() { /* ... */ } } $Libraries = new Libraries; $controller = 'News'; // Would be determined from Query String $method = 'index'; // Would be determined from Query String $Content = $Libraries->load_class('controller', $controller); //create the controller for the specific page if (in_array($method, get_class_methods($Content))) { call_user_func(array($Content, $method)); } else { die('Bad Request'. $method); } $Content::$var = 'Goodbye World'; echo $Libraries::$var . ' - ' . $Content::$var; ?> /* Ouput */ 0 1 2 3 Goodbye World! - Goodbye World

Read the article

How do I launch a WPF app from command.com. I'm getting a FontCache error.

- by jttraino

I know this is not ideal, but my constraint is that I have a legacy application written in Clipper. I want to launch a new, WinForms/WPF application from inside the application (to ease transition). This legacy application written in Clipper launches using: SwpRunCmd("C:\MyApp\MyBat.bat",0) The batch file contains something like this command: C:\PROGRA~1\INTERN~1\iexplore "http://QASVR/MyApp/AppWin/MyCompany.MyApp.AppWin.application#MyCompany.MyApp.AppWin.application" It is launching a WinForms/WPF app that is we deploy via ClickOnce. Everything has been going well until we introduced WPF into the application. We were able to easily launch from the legacy application. Since we have introduced WPF, however, we have the following behavior. If we launch via the Clipper application first, we get an exception when launching the application. The error text is: The type initializer for 'System.Windows.FrameworkElement' threw an exception. at System.Windows.FrameworkElement..ctor() at System.Windows.Controls.Panel..ctor() at System.Windows.Controls.DockPanel..ctor() at System.Windows.Forms.Integration.AvalonAdapter..ctor(ElementHost hostControl) at System.Windows.Forms.Integration.ElementHost..ctor() at MyCompany.MyApp.AppWin.Main.InitializeComponent() at MyCompany.MyApp.AppWin.Main..ctor(String[] args) at MyCompany.MyApp.AppWin.Program.Main(String[] args) The type initializer for 'System.Windows.Documents.TextElement' threw an exception. at System.Windows.FrameworkElement..cctor() The type initializer for 'System.Windows.Media.FontFamily' threw an exception. at System.Windows.Media.FontFamily..ctor(String familyName) at System.Windows.SystemFonts.get_MessageFontFamily() at System.Windows.Documents.TextElement..cctor() The type initializer for 'MS.Internal.FontCache.Util' threw an exception. at MS.Internal.FontCache.Util.get_WindowsFontsUriObject() at System.Windows.Media.FontFamily.PreCreateDefaultFamilyCollection() at System.Windows.Media.FontFamily..cctor() Invalid URI: The format of the URI could not be determined. at System.Uri.CreateThis(String uri, Boolean dontEscape, UriKind uriKind) at System.Uri..ctor(String uriString, UriKind uriKind) at MS.Internal.FontCache.Util..cctor() If we launch the application via the URL (in IE) or via the icon on the desktop first, we do not get the exception and application launches as expected. The neat thing is that whatever we launch with first determines whether the app will launch at all. So, if we launch with legacy first, it breaks right away and we can't get the app to run even if we launch with the otherwise successful URL or icon. To get it to work, we have to logout and log back in and start it from the URL or icon. If we first use the URL or the icon, we have no problem launching from the legacy application from that point forward (until we logout and come back in). One other piece of information is that we are able to simulate the problem in the following fashion. If we enter a command prompt using "cmd.exe" and execute a statement to launch from a URL, we are successful. If, however, we enter a command prompt using "command.com" and we execute that same statement, we experience the breaking behavior. We assume it is because the legacy application in Clipper uses the equivalent of command.com to create the shell to spawn the other app. We have tried a bunch of hacks like having command.com run cmd.exe or psexec and then executing, but nothing seems to work. We have some ideas for workarounds (like making the app launch on startup so we force the successful launch from a URL, making all subsequent launches successful), but they all are sub-optimal even though we have a great deal of control over our workstations. To reduce the chance that this is related to permissions, we have given the launching account administrative rights (as well as non-administrative rights in case that made a difference). Any ideas would be greatly-appreciate. Like I said, we have some work arounds, but I would love to avoid them. Thanks!

Read the article

Neo4j increasing latency as SKIP increases on Cypher query + REST API

- by voldomazta

My setup: Java(TM) SE Runtime Environment (build 1.7.0_45-b18) Java HotSpot(TM) 64-Bit Server VM (build 24.45-b08, mixed mode) Neo4j 2.0.0-M06 Enterprise First I made sure I warmed up the cache by executing the following: START n=node(*) RETURN COUNT(n); START r=relationship(*) RETURN count(r); The size of the table is 63,677 nodes and 7,169,995 relationships Now I have the following query: START u1=node:node_auto_index('uid:39') MATCH (u1:user)-[w:WANTS]->(c:card)<-[h:HAS]-(u2:user) WHERE u2.uid <> 39 WITH u2.uid AS uid, (CASE WHEN w.qty < h.qty THEN w.qty ELSE h.qty END) AS have RETURN uid, SUM(have) AS total ORDER BY total DESC SKIP 0 LIMIT 25 This UID has about 40k+ results that I want to be able to put a pagination to. The initial skip was around 773ms. I tried page 2 (skip 25) and the latency was around the same even up to page 500 it only rose up to 900ms so I didn't really bother. Now I tried some fast forward paging and jumped by thousands so I did 1000, then 2000, then 3000. I was hoping the ORDER BY arrangement will already have been cached by Neo4j and using SKIP will just move to that index in the result and wont have to iterate through each one again. But for each thousand skip I made the latency increased by alot. It's not just cache warming because for one I already warmed up the cache and two, I tried the same skip a couple of times for each skip and it yielded the same results: SKIP 0: 773ms SKIP 1000: 1369ms SKIP 2000: 2491ms SKIP 3000: 3899ms SKIP 4000: 5686ms SKIP 5000: 7424ms Now who the hell would want to view 5000 pages of results? 40k even?! :) Good point! I will probably put a cap on the maximum results a user can view but I was just curious about this phenomenon. Will somebody please explain why Neo4j seems to be re-iterating through stuff which appears to be already known to it? Here is my profiling for the 0 skip: ==> ColumnFilter(symKeys=["uid", " INTERNAL_AGGREGATE65c4d6a2-1930-4f32-8fd9-5e4399ce6f14"], returnItemNames=["uid", "total"], _rows=25, _db_hits=0) ==> Slice(skip="Literal(0)", _rows=25, _db_hits=0) ==> Top(orderBy=["SortItem(Cached( INTERNAL_AGGREGATE65c4d6a2-1930-4f32-8fd9-5e4399ce6f14 of type Any),false)"], limit="Add(Literal(0),Literal(25))", _rows=25, _db_hits=0) ==> EagerAggregation(keys=["uid"], aggregates=["( INTERNAL_AGGREGATE65c4d6a2-1930-4f32-8fd9-5e4399ce6f14,Sum(have))"], _rows=41659, _db_hits=0) ==> ColumnFilter(symKeys=["have", "u1", "uid", "c", "h", "w", "u2"], returnItemNames=["uid", "have"], _rows=146826, _db_hits=0) ==> Extract(symKeys=["u1", "c", "h", "w", "u2"], exprKeys=["uid", "have"], _rows=146826, _db_hits=587304) ==> Filter(pred="((NOT(Product(u2,uid(0),true) == Literal(39)) AND hasLabel(u1:user(0))) AND hasLabel(u2:user(0)))", _rows=146826, _db_hits=146826) ==> TraversalMatcher(trail="(u1)-[w:WANTS WHERE (hasLabel(NodeIdentifier():card(1)) AND hasLabel(NodeIdentifier():card(1))) AND true]->(c)<-[h:HAS WHERE (NOT(Product(NodeIdentifier(),uid(0),true) == Literal(39)) AND hasLabel(NodeIdentifier():user(0))) AND true]-(u2)", _rows=146826, _db_hits=293696) And for the 5000 skip: ==> ColumnFilter(symKeys=["uid", " INTERNAL_AGGREGATE99329ea5-03cd-4d53-a6bc-3ad554b47872"], returnItemNames=["uid", "total"], _rows=25, _db_hits=0) ==> Slice(skip="Literal(5000)", _rows=25, _db_hits=0) ==> Top(orderBy=["SortItem(Cached( INTERNAL_AGGREGATE99329ea5-03cd-4d53-a6bc-3ad554b47872 of type Any),false)"], limit="Add(Literal(5000),Literal(25))", _rows=5025, _db_hits=0) ==> EagerAggregation(keys=["uid"], aggregates=["( INTERNAL_AGGREGATE99329ea5-03cd-4d53-a6bc-3ad554b47872,Sum(have))"], _rows=41659, _db_hits=0) ==> ColumnFilter(symKeys=["have", "u1", "uid", "c", "h", "w", "u2"], returnItemNames=["uid", "have"], _rows=146826, _db_hits=0) ==> Extract(symKeys=["u1", "c", "h", "w", "u2"], exprKeys=["uid", "have"], _rows=146826, _db_hits=587304) ==> Filter(pred="((NOT(Product(u2,uid(0),true) == Literal(39)) AND hasLabel(u1:user(0))) AND hasLabel(u2:user(0)))", _rows=146826, _db_hits=146826) ==> TraversalMatcher(trail="(u1)-[w:WANTS WHERE (hasLabel(NodeIdentifier():card(1)) AND hasLabel(NodeIdentifier():card(1))) AND true]->(c)<-[h:HAS WHERE (NOT(Product(NodeIdentifier(),uid(0),true) == Literal(39)) AND hasLabel(NodeIdentifier():user(0))) AND true]-(u2)", _rows=146826, _db_hits=293696) The only difference is the LIMIT clause on the Top function. I hope we can make this work as intended, I really don't want to delve into doing an embedded Neo4j + my own Jetty REST API for the web app.

Search Results

Search found 7159 results on 287 pages for 'forward compatibility'.

Page 273/287 | < Previous Page | 269 270 271 272 273 274 275 276 277 278 279 280 | Next Page >

- by bala

- by seaquest

- by Joy

- by AVandelay05

- by Andreas Krueger

- by mojotaker

- by Martin Wiboe

- by Billy Talented

- by Jeff Lee

- by Faur Ioan-Aurel

- by prince23

- by dok

- by HeavyWave

- by Hooplad

- by amiv

- by James

- by cookiecaper

- by brazorf

- by jasonmp85

- by Panthe

- by Peter Bailey

- by Ehsan

- by bigstylee

- by jttraino

- by voldomazta

< Previous Page | 269 270 271 272 273 274 275 276 277 278 279 280 | Next Page >