Search Results

Search found 10313 results on 413 pages for 'hardware sharing'.

Page 294/413 | < Previous Page | 290 291 292 293 294 295 296 297 298 299 300 301  | Next Page >

• Raid recovery in gigabyte GA-8I945 Pro

  - by epeleg

  This was a working machine until a few days ago. And now it won't boot into the OS, during startup if makes clicking sounds (I think from one of the drives). Installed OS: Windows 2003 Web edition Hardware: Gigabyte GA-8I945P Pro , 2*160G Sata in RAID1 configuration , 2 Volumes – 25G and the rest. When I installed windows on it, during setup, I pressed F6 and used ICH7DH drivers of RAID. The manual for the MOBO says: Step 1: After the POST memory test begins and before the operating system boot begins, look for a message which says "Press to enter Configuration utility" (Figure 4). Press CTRL+ I to enter the RAID BIOS setup utility. But the machine never shows this message. BIOS SATA RAID/AHCI Mode is set to RAID. Any ideas or pointers on what I can do to recover my data? Thanks

  Read the article

• end_request: I/O error, dev sda, sector xxxxxxxxx

  - by muruga

  I have a IBM server. This server contains 3 hard disk with RAID 5. It was working fine earlier. Unfortunately this machine got the following error message. After that I have rebooted the systems. After that I am getting the following error message in kern.log and demsg kernel: [65896.678870] end_request: I/O error, dev sda, sector 17430271 kernel: [69263.783957] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK : [69263.783957] sd 0:0:0:0: [sda] Sense Key : Hardware Error [current] kernel: [69263.783957] sd 0:0:0:0: [sda] Add. Sense: Internal target failure Whether it is kernel problem or hard disk problem or Raid problem

  Read the article

• Slow write speeds on new Gigabit home file server

  - by Ryan Holder

  So I finally got all my parts delivered to setup a home file/backup server this week. It's currently running Ubuntu Server and I'm using Samba to share files on my network. The server currently has a 2TB WD Green drive in it connected to a Asus M5A78L-M This is then connected via CAT6a to my new Gigabit switch (TP-Link TL-SG1005D). My home desktop is then also connected to this switch and again also through CAT6a cable. Currently when transfering files I will get a perfect 100MB/s read from the server to my Windows machine. When copying from my Windows machine to the server I get around 30/38MB/s. I know this drive is capable is faster speeds so would anybody have an idea of where the bottleneck is? Any help would be greatly appreciated :) EDIT: I have found ftp's write speed is much closer to what my Samba read speed is so I'm going to give it a guess that is a software problem rather than hardware

  Read the article

• openSuse full disk encryption

  - by djechelon

  I'm a proud Suser. I'm about to reinstall 12.2 on my ASUS N76VZ (UEFI x64 laptop). Since I'm very sensitive about laptop security against theft or unwanted inspection, I chose to use BitLocker with USB dongle in Windows 7. When installing Suse the last time I found that only the home partition (separated from root) was capable of being encrypted. Does Suse offer a full disk encryption solution like BitLocker that I haven't discovered yet? Or is encrypting home partition the only way to protect data? Encrypting only home is feasible as one stores personal data in home, but I still would like to encrypt the whole thing! Also, using a hardware token (no TPM available) for unlocking is preferred to password, if possible! Thanks

  Read the article

• How do I fix "Setup did not find any hard disk drives installed in your computer" error during Win XP Pro install?

  - by CT.

  I just bought a nettop. It came with WinXP Home. I first installed Win 7 on it. I wasn't that happy with the performance so I decided to go back to XP. I am using an external dvd drive and a Win XP Pro disc. I boot from the dvd drive and during the install get this error: Setup did not find any hard disk drives installed in your computer. Make sure any hard disk drives are powered on and properly connected to your computer, and that any disk-related hardware configuration is correct. This may involve running a manufacturer-supplied diagnostic or setup program. Setup cannot continue. To quit Setup, press F3. This is the nettop in question: http://www.newegg.com/Product/Product.aspx?Item=N82E16883103228

  Read the article

• Can I take a HDD in Raid1 and plug it straight into a different machine?

  - by jacko

  I would assume that I can just take my HDD out of my NAS (in raid1 mirror) and plug it into another enclosure and have it work off the bat but I'd like to make sure... Any ideas? Edit: My current setup is a Netgear ReadyNAS in (hardware) raid1. I'm hoping to replace this with a home theatre type PC (possibly running Ubuntu), and would like to migrate my data without having to do a bulk transfer over my network between the 2 machines. Can anyone confirm the case for the Netgear ReadyNAS?

  Read the article

• Black screen during startup

  - by Juanillo

  Hello, I've got a friend with a weird problem. When he starts his computer the screen is completely black untile the computer is completely started. So the screen is black until it suddenly shows the windows desktop. He said that this is happening since a technical service repaired his computer, but that repairment is not now in warranty. Recently the computer stopped working, but as the screen is black he cannot access to Bios or to secure start-up (by pressing F8). When he inserts the Windows Vista DVD the system doesn't boot from DVD (it musn't be configured in this way in the Bios.) Maybe there´s a problem with the hardware (maybe the graphic card). Can anyone explain a reason why the screen is black during start-up? Any idea of what to do with the computer to restore it? Thanks.

  Read the article

• My Network adapter "D-Link DWA-547" is causing windows 7 to freeze up.

  - by Anders

  Any audio playing, and sometimes the program i am using is constantly stuttering and freezing up. I have narrowed the offending hardware down to my: D-Link DWA-547 RangeBooster N650 Desktop Adapter If i disable it in the device manager everything runs fine and smooth. The card works, and gives me super fast internet. But the rest of the system hangs. I have tried installing the card with the drivers from the cd that came with it, i also tried the lates beta drivers from the d-link webpage, but the problem persists. What do i do? I am running windows 7 x64 on a asus p5b motherboard with 2 intel processors.

  Read the article

• Canon HV20 recognized, but no drivers in Windows 7 x64

  - by Tuminoid

  My Canon HV20 camcorder is properly recognized when connected via Firewire to Windows 7 x64, but no drivers are installed for it. Windows or I cannot locate any drivers for it as, but it should be working off-the-shelf. I googled a lot, and found instructions to set IEEE 1394 host to legacy mode via Device Manager, but Windows doesn't offer me the legacy option at all. If I check the properties of Canon&HV20 device in Other devices section it says The drivers for this device are not installed. (Code 28) There is no driver selected for the device information set or element. It used to work just fine on my previous installation of Vista x64 and same hardware :/

  Read the article

• Taking over and Moving a PHP site

  - by KCavon

  I have a internal use PHP site at my new position. It only runs a few days a year off site so we keep it on laptops. The hardware it has been on, a 8 year IBM Thinkpad running Fedora, is dying. I have new Lenovo Thinkpad's running latest and greatest Ubuntu. I have copied the contents of var to a shared drive, renamed the old www folder in var on the new machine and copied over the old www folder. I can get to the login page and into the site, but when I look something up it returns Cannot Open. I know I cannot get to the MySQL in the new machine because users and passwords dont match. The version of the PHP from the old machine is before the setup script was included. I know very little about PHP. I am looking for input on the proper way to link the old PHP files to my mysql instance. Any help, much appreciated.

  Read the article

• OpenBSD Routing Problem

  - by Ozkan SENOVA

  I am running OpenBSD on a network appliance hardware. It has 5 NICs. I want to give different IP's in same subnet to 3 nics. Eg: em0: 192.168.1.5 em1: 192.168.1.90 em2: 192.168.1.56 I make the necessary configuration with ifconfig, all interfaces works as expected when all the ethernet ports are plugged in to switch. But there is something wrong in routing. If I connect to 192.16.1.5 via any service(http, smtp etc.), traffic goes over link#3. If I unpug the cable from em2 I can't reach any IP's binded on device. Is there any way to route traffic over different links in this IP configuration?

  Read the article

• Blank screen after grub menu

  - by Tim

  I just rebooted an Ubuntu Server 10.04. After choosing boot options in the grub menu, though, it just displays a black screen with the blinking white underscore in the upper-left corner. The machine has had (hardware) trouble with networking before, but the problem remains after 10 minutes, so I don't think it's the problem now. Booting into recovery mode or using earlier kernels yields the same problem. This also happens if I boot from another hard-drive. I haven't yet tried to boot from CD as the machine lacks a CD reader. How should I diagnose the problem? Update: My boot options are: recordfail insmod ext2 set root='(hd0,1)' search --no-floppy --fs-uuid --set 567[redacted] linux /boot/vmlinuz-2.6.32-29-generic root=UUID=567[redacted] ro quiet splash initrd /boot/initrd.img-2.6.32-29-generic Update: Also, I cannot access the virtual terminals (ctrl+alt+Fn).

  Read the article

• Load balancing + NAT issue on BNT GBE 2-7 gear

  - by Clément Game

  Hi guys, I've got troubles configuring an Hardware load-Balancer with NAT functions. I have the following architecture: Internet === VIP (public) LB (private ip) ==== private addressed servers When a connection is initialised from the outside (internet) , the LB correctly forwards the SYN packet to one of the private servers. But when these servers want to reply with a SYN/ACK there is a problem. the initial SYN packet had as ip header : VIP = Private_server_Address But the private servers cannot reach VIP from their side (this is normal since it's nated), and then provide a correct reply. Have you guys any solution to correctly forward the packets to their correct destination ? Note: The load balancer, which is the default gw for the servers, also has a NAT rule for "masquerading" (actually more SNAT than real masquerading) Regards, Clément.

  Read the article

• VMware ESX 3.5 Host Health shown as unknown

  - by dunxd

  I have an ESX 3.5 update 5 cluster of five host servers, all fully patched as of this Friday. Today I noticed that one of the servers has the Hardware Health status as unknown in Virtual Center Infrastructure Client. When I look at the Health Status view under configuration for that host, all the items are status Unknown. The server is exactly the same configuration as the others - same model (HP DL360 G5), memory, NICs etc. I have tried restarting the management service with service mgmt-vmware restart but this has not resolved the issue. Asides from this, I am not seeing any issues with the cluster - however, I hate having a blind spot like this. Any ideas?

  Read the article

• SAS disk performance drops a while after reboot.

  - by Flamewires

  So we have some workstations with identical hardware. The Fedora14 box has a couple weeks uptime and still get good performance. hdparm -tT /dev/sda /dev/sda: Timing cached reads: 21766 MB in 2.00 seconds = 10902.12 MB/sec Timing buffered disk reads: 586 MB in 3.00 seconds = 195.20 MB/sec The Cent 5.5 boxes however seem to be okay after a reboot, /dev/sda: Timing cached reads: 34636 MB in 2.00 seconds = 17354.64 MB/sec Timing buffered disk reads: 498 MB in 3.01 seconds = 165.62 MB/sec but some time later( unsure exactly, tested at approx 1 day uptime) /dev/sda: Timing cached reads: 2132 MB in 2.00 seconds = 1064.96 MB/sec Timing buffered disk reads: 160 MB in 3.01 seconds = 53.16 MB/sec drop to this. This is with very low load. I believe they all have the same bios settings. Any ideas what could cause this on Cent? Ask for more info. It might also be worth noting, that passing the --direct flag causes the slow boxes to perform similarly to the non-slow ones for buffered disk reads.

  Read the article

• Running multipul lines through a server.

  - by Kevin Roberson

  I am looking to buy numbers in bulk on DIDx.net. After I purchase the numbers in a particular area code, I want to forward those numbers to other numbers that are outside of that area code. This way it will be seen as a local call versus long distance. I have the customers but I don't have the system I need. I have read about Asterisk, VOIP, SIP, and BYOH. But I have no clue what will be the best system for me. Does anyone have any idea what my next step should be when it comes to hardware and software? Or what type of operating system I should use? I basically want to set up a system like GoogleVoice & Phonebooth.

  Read the article

• Why does booting from a 64 bit Win 8 USB install work on a 32 bit laptop?

  - by Arabella

  I upgraded a 64 bit Windows 7 laptop to Windows 8 through the Upgrade Assistant, creating a bootable USB without any problems. I installed it successfully. Before I purchased an upgrade for my 32 bit Windows 7 laptop, I decided to boot from the USB with the 64 bit ISO to see what happened. The Windows 8 install screen came up with all the options. Should it not have detected that the laptop is 32 bit and therefore the install should have given an error? I cancelled the install before it did anything, but now I want to know if I need to download the iso again after purchasing the upgrade on my 32 bit laptop? I've read the answers to this question, which confirms what is said in this article - a 32 or 64 bit iso will be downloaded depending on the hardware of the computer you are upgrading. If that is the case, then why did it boot into the install screen?

  Read the article

• How to Virtualize an OEM windows install.

  - by jumentous

  I've bought a new computer and like always it comes with windows 7 pre-installed. I'm a linux user by default but i still keep a virtual windows installation around. Is it possible to install my linux distribution, and use the OEM license that came with the computer to create the virtual instance? I have no intention of moving the license off the physical machine so i'm sure i could argue that i'm not violating the license but i don't expect that this would work and activate without great legal battles. So in the event that this doesn't work what other options do i have? Can i shrink the physical partition and have Qemu boot it? My thoughts are that windows would detect the change in hardware and fail. What can i do with this windows install as a linux user?

  Read the article

• RS-232 vs. RS-485

  - by user60524

  Doing a little research on the two to figure out which one may better suit my purposes (communications amongst different hardware). How do they fare against one another? Im far from being a specialist and have no idea where I would even start looking for data to compare and contrast. If possible can someone please answer the following questions in regards to each of these. Can they be networked amongst each other? Can they be easily networked over ethernet? What speeds do they transfer at? (Min, Max, Etc.) Reliability? Best framework to build on top of to support the above? Any standard communications programs? Debugging capability? Any help would be very much appreciated, thanks.

  Read the article

• Making an SSD drive the primary boot/system drive

  - by David Ebbo

  [Not much of a hardware guy, so please excuse my ignorance :)] I just ordered an HP Pavilion Elite HPE-450t (desktop), which came with Win7 installed on the hard drive, using two partitions (C: and D:). Separately, I bought a 128GB SSD that I intend to use as my system drive. I got it in there and connected it, and right now, it's the J: drive (which was the first letter available in disk manager). My goal is for the SSD to get a clean OS install be the C: drive, and to clean out the other hard drive and make it D: (for misc data storage) Question #1: the motherboard has two SATA plugs. Does it matter which one I use for which drive? Question #2: what's the right way to install Win7 on the SSD in a way that it ends up being the C: drive? Do I need to switch some things around in the current Win7 that came with it, are can I do all that while installing Win7 on the SSD?

  Read the article

• Can I use CAT 6a connectors with 7a cable (and get 6a performance)?

  - by Mr. Flibble

  I'm re-wiring a building and want to get the best cable possible laid - it required re-plastering to make a change to the cables and the cables will be there for the next 10 - 20 years. Currently there appears to be cat 7a cable available but not too much in the way of cat 7a connectors. Also - I won't be using 40Gig hardware in the near future. So, my question: is it possible to use cat 6a connectors / patch panels with cat 7a cable and get the same performance as I would had I used cat 6a cable? Are there any gotchas in trying to do this?

  Read the article

• Windows 7 x64 Hard Freezing (again)

  - by Lanissum

  Awhile ago, my computer was randomly freezing a few minutes after booting, and I ended up replacing the CPU and mobo after testing the RAM and hard drive, I also couldn't find anything wrong with the video card. So after replacing the presumably faulty hardware, everything worked fine for about a month and a half. All of a sudden, My computer is randomly freezing a few minutes after loading up any intensive application (games, mostly). Most of the time it just freezes with the current frame until I hard reset, although once it printed a BSOD message stating that dxgmms1.sys was to blame. The only difference between these two episodes I can think of is that I can do word/internet/work without issue now, as opposed to the near uselessness my computer was rendered last time. For those of you who want to know, I tested my memory with memtest86 (for 64 bit machines). I can't figure out what could have started this latest round of issues, the event logger just states that a kernel-power event has occurred (like last time) but I think thats just a generic "this machine has rebooted after a sudden shutdown" message.

  Read the article

• Using VMware's ESXi, can I plug in 30 USB Wireless adapters and allow each of 30 VMs one?

  - by 31eee384

  I'm assuming ESXi will act very similarly to VMware Workstation or other products, so answers based on knowledge of those programs might also help. I want to plug in 30 USB Wireless or Ethernet adapters into my server, and let each VM access one and only one of these devices. Unfortunately, I don't have the hardware to just try it out as the purchase of hubs and adapters hinges on the result of this question. The answer could be a resounding "yes, easy!" and that would be great. I couldn't find any answers to this question with google, and it's possible that this is because it's so easy to do. Thanks!

  Read the article

• How to switch off the monitor when mouse reaches the edge of the screen?

  - by evgeny9

  I have 2 computers at home (Windows XP and Windows 7), but one monitor for both of them. They are connected to this monitor using different interfaces: DVI and VGA. I'm also using one keyboard and one mouse to control both PCs with the help of Synergy or Input Director. But I still need to manually switch between monitor interfaces. I wonder, if there's some way (software) that will switch this interfaces (turn off the monitor), when reach the edge of the screen with the mouse. Until now I found several answers, which help to avoid pressing hardware buttons, but still can not do the job automatically based on mouse pointer coordinates. Thank you.

  Read the article

• Setting up Mac VPN on simple network with separate IPs

  - by Dave

  Hi there, We have a pretty simple network configuration. A typical ASDL line with two extra IP addresses. We have a basic home network router Dlink DIR-655. We have two Mac OS X Snow Leopard Servers that we want to setup VPN on. The problem is that we can't change the ports which VPN works under ie. we can only setup port forwarding for UDP 500,1701,4500 to a single server. I'm wondering how we can cost effectively re-work our network so that we can take advantage of the separate IP addresses and have both VPNs working with the same router. Is that possible with our current hardware setup or do we need something more powerful? We're also toying with Mobile Access and wondering if that might be easier to setup. Expert help is greatly appreciated.

  Read the article

< Previous Page | 290 291 292 293 294 295 296 297 298 299 300 301  | Next Page >