Search Results

Search found 10756 results on 431 pages for 'zend controller'.

Page 294/431 | < Previous Page | 290 291 292 293 294 295 296 297 298 299 300 301  | Next Page >

• OpenVPN Configuration - Windows 7 client & debian server

  - by Guillaume

  I recently formatted my Windows 7 computer and lost my client's config files for OpenVPN. I recovered the certificates and default config that were left on the server but I haven't managed to make the whole thing work again. I assume the server's config and routing table are OK because it was working before (although quite some time ago). Would any of you experts be able to help? server.conf # Serveur TCP/666 mode server proto udp port 666 dev tun # Cles et certificats ca ca.crt cert server.crt key server.key dh dh1024.pem tls-auth ta.key 0 cipher AES-256-CBC # Reseau server 10.8.0.0 255.255.255.0 #push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 208.67.222.222" push "dhcp-option DNS 208.67.220.220" push "redirect-gateway def1" keepalive 10 120 # Securite user nobody group nogroup chroot /etc/openvpn/jail persist-key persist-tun comp-lzo # Log verb 3 mute 20 status openvpn-status.log log-append /var/log/openvpn.log client.conf # Client client dev tun proto udp remote *my server's ip address*:666 cipher AES-256-CBC # Cles ca ca.crt cert client1.crt key client1.key tls-auth ta.key 1 # Securite nobind persist-key persist-tun comp-lzo verb 3 Routing table on debian server when OpenVPN server is running: Destination Gateway Genmask Indic Metric Ref Use Iface 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 my server's ip * 255.255.255.0 U 0 0 0 eth0 default 72815.trg.dedic 0.0.0.0 UG 0 0 0 eth0 Routing table on Windows 7 client (OpenVPN not working) =========================================================================== Interface List 19...00 f0 8a 1b 6e 5c ......TAP-Win32 Adapter V9 12...90 2e 34 33 84 7b ......Atheros AR8151 PCI-E Gigabit Ethernet Controller ( NDIS 6.20) 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.11 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.11 276 192.168.1.11 255.255.255.255 On-link 192.168.1.11 276 192.168.1.255 255.255.255.255 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.11 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.11 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: [...] =========================================================================== Persistent Routes: None And when the link is established between my client and the server: The server's routing table stays the same. The client's becomes: =========================================================================== Interface List 19...00 f0 8a 1b 6e 5c ......TAP-Win32 Adapter V9 12...90 2e 34 33 84 7b ......Atheros AR8151 PCI-E Gigabit Ethernet Controller ( NDIS 6.20) 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.11 20 0.0.0.0 128.0.0.0 10.8.0.5 10.8.0.6 30 10.8.0.1 255.255.255.255 10.8.0.5 10.8.0.6 30 10.8.0.4 255.255.255.252 On-link 10.8.0.6 286 10.8.0.6 255.255.255.255 On-link 10.8.0.6 286 10.8.0.7 255.255.255.255 On-link 10.8.0.6 286 my server's ip 255.255.255.255 192.168.1.1 192.168.1.11 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.0.0.0 128.0.0.0 10.8.0.5 10.8.0.6 30 192.168.1.0 255.255.255.0 On-link 192.168.1.11 276 192.168.1.11 255.255.255.255 On-link 192.168.1.11 276 192.168.1.255 255.255.255.255 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 10.8.0.6 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.11 276 255.255.255.255 255.255.255.255 On-link 10.8.0.6 286 =========================================================================== Persistent Routes: None What's working: Server and client do connect to each other, SSL certificates are OK. The client gets an IP (10.8.0.6) from the server OpenVPN client is started as an administrator. But: I cannot ping the other one on either side. 'Gateway' value is empty on client's side (in the adapter's "status" window). Client has got no internet access when the link is up. Ideal configuration: I only want the client to be able to use the server's Internet access and access its resources (MySQL server in particular). I do not need or want the server to access the client's local network. The client needs to be able to access it's local network, although all Internet traffic should be redirected to the VPN link. I spent a considerable amount of time on this but it's still not working, any help would be much appreciated. Thanks :)

  Read the article

• Ubuntu on an XPS 14 Ultrabook with mSATA cache and 500GB HD - how to partition for dual boot?

  - by JDS

  I am getting an XPS 14 ( http://www.dell.com/us/p/xps-14-l421x/pd ) and I want to dual-boot Windows and Ubuntu. This thing has a 500GB standard HD and a 32GB mSATA that can be used as cache. Does anyone know how this thing is partitioned? Is the OS installed on the mSATA drive and data is on the big HD? Is there a BIOS controller or maybe even a Windows driver that makes the mSATA drive and 500GB HD appear contiguous? I get the impression that something makes the mSATA be used invisibly as cache, but I can't find any technical documentation how that works. My primary concern here is wrt dual-booting Ubuntu. I want to know if I need to partition the mSATA separately, or the big HD, or just partition the "magic" contiguous disk space that appears available to the OS.

  Read the article

• Failure to copy files with ownership/ACL information on a Windows Server 2008 R2 machine

  - by darklion

  I'm attempting to copy a directory tree, maintaining its ownership information using the command: XCOPY S:\ProjectsDefault\Tempalte\admin S:\Projects\00\111\admin /S /E /I /O the command gives an Access denied error message, and while it does create the directory tree, the ownership and ACL information is not copied. This is being done on a Windows 2008 R2 Server which has mounted a share from a Windows 2003 R2 domain controller. The user has been been granted full access to the share and is a member of the Domain Admins security group. Oddly enough, the command does work if performed on a different (Windows 2003 R2 Server). (It also works if done using the Domain Administrator account on the 2008 server.)

  Read the article

• MDADM RAID5 array showing as CLEAN FAULTY

  - by Dean Reilly

  A drive dropped out of my raid 5 array yesterday. It looks like the reason was due to a bad controller so I switched it out and attempted to re-add the drive but mdadm claimed it couldn't do it. So I zerod the superblock and just added the drive normally and left it to resync. When I came to check on the array this morning I was unable to mount it at all and it's now showing as CLEAN FAULTY with two drives missing. The two missing drives are listed as spare and faulty spare. Is there anything I can do in this situation or is the array gone?

  Read the article

• Server 2003 RAS Server Utilising High WAN Traffic

  - by Joe Sergeant

  We have Routing and Remote Access configured on Server 2003 (also our primary domain controller), allowing users to connect in remotely to access files, email, etc. With one user, the RAS Server is constantly sending data to that user's remote computer. From 9am this morning it has transferred almost 800MB. The user isn't transferring any files remotely, certainly not enough to total 800MB anyway. None of the other remote users have had this issue. We have ensured that the user in question has "Use default gateway on remote network" disabled for both IPv4 and IPv6 and we are fairly confident that Offline Files isn't trying to synchronise with the server remotely, too. My question is two-fold. Firstly, has anyone had a similar experience? Secondly, what would be the best software to discover exactly what data is being sent to the remote user?

  Read the article

• Prevent users from creating / copying / moving anything except .exe

  - by webnoob

  We have a program that compiles executables into a folder into c:\bin. Ideally I would like to share this folder so users can access the exe's within but stop them creating any other files in there. The reason for this is to stop users grabbing source code and putting it in a shared drive then taking it. We have a Domain Controller setup and all the users belong to a specific security group. Is there any way to achieve this? EDIT: TO clarify, I need to stop users from creating or moving files INTO the C:\bin folder which are not executables.

  Read the article

• Is it safe to run an operating system from an USB flash drive?

  - by Georg

  I've got a laptop that has a broken harddisk controller. Replacing the motherboard is quite expensive. I thought about buying a flash drive and installing & running the system from it. However, I'm concerned about some things. Speed: Are they fast enough for swap memory (I've got only 1GB RAM installed.) I'm considering buying 2 or 3 of them and making them into a RAID. What about limited write cycles? How long will it last for a system that has a filesystem with journaling enabled? I'd hate to abandon it. Are there significant differences between internal SSD which are used in modern laptops like MacBooks and USB flash drives? What should I expect in 10 years when the memory wear starts kicking in?

  Read the article

• Replacing sick NTP server source and re-synching (with internal time currently 2 minutes late)

  - by l0c0b0x

  One of the external NTP servers (the primary one--currently) we're using as source seems to not be responding to NTP calls. Unfortunately, on our core router (Cisco 6509), the NTP functionality hasn't switched to the secondary NTP external server as it was expected. As a result, our core router which is pretty much our main internal NTP source is 2 minutes late. I'm planning to fix the external router issue by making the external NTP source be the one currently working. I'm wondering, how much will a 2 minute change affect my users and services? Specially since these days, we're heavily relying on certificate-based authentication. We're a Windows/Cisco shop. Internal NTP setup: [Core Router 1 / Cisco 6509]: looking out to two external NTP servers (in which the primary one is not responding to NTP calls) [Core Router 2]: Synching with Core router 1 (primary), working external router (secondary) [Other Cisco network devices]: Synching with Core router 1 (primary), core router 2 (secondary) [Domain controller(s)]: Synching with Core router 1 [All windows clients/servers]: Synching with domain controllers

  Read the article

• Creating a new Active Directory account with an InfoPath form

  - by ryan

  I am setting up a business partner portal in our Sharepoint server. There will be an AD group with permissions limited to viewing and possibly contributing to the specific business partner site and employees of our business partners will have accounts created for them as needed. Now we would like to let our business development group(BDG) have control over the partner accounts. Ideally they should be able to add and delete accounts and change permissions on them. The BDG are not domain admins so we don't want to give them access to the domain controller. We want to create an Infopath form that will allow them to do all this. Is it possible to create and manage AD accounts from within an Infopath form on the sharepoint server? I searched this site and MSDN and can not find anything specifically related to my question.

  Read the article

• No Internet access while being connected to VPN using Cisco VPN Client 5.

  - by szeldon

  Hi, I have an access to corporate VPN using Cisco VPN Client 5.0.00:0340, but when I'm connected to it, I don't have an Internet access. I'm using Windows XP SP3. As it was suggested here http://forums.speedguide.net/showthread.php?t=209167 , I tried to enable "Allow local LAN Access" but it doesn't work. I also tried a second solution - deleting entry using "route" command, but it didn't help. I used "route delete 192.168.100.222". It's a third day of my attempts to solve this issue and I don't have an idea what else to do. I'm not very experienced in VPN stuff, but I know something about networking. Basing on my knowledge, I think that it's theoretically possible to achieve Internet access using my local network and only corporate stuff to be routed using VPN connection. I think that theoretically this should look like this: every IP being inside by corporation - VPN interface IP every other IP - my ethernet interface I've tried many possibilities of how to change those routes, but neither of them work. I'd really appreciate any help. My route configuration before connecting to VPN: =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 c0 a8 de 79 01 ...... Atheros AR5006EG Wireless Network Adapter - Teefer2 Miniport 0x10005 ...02 00 4c 4f 4f 50 ...... Microsoft Loopback Card 0x160003 ...00 17 42 31 0e 16 ...... Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller - Teefer2 Miniport =========================================================================== =========================================================================== Active routes: Network Destination Netmask Gateway Interface Metrics 0.0.0.0 0.0.0.0 192.168.101.254 192.168.100.222 10 10.0.0.0 255.255.255.0 10.0.0.10 10.0.0.10 30 10.0.0.10 255.255.255.255 127.0.0.1 127.0.0.1 30 10.255.255.255 255.255.255.255 10.0.0.10 10.0.0.10 30 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.100.0 255.255.254.0 192.168.100.222 192.168.100.222 1 192.168.100.222 255.255.255.255 127.0.0.1 127.0.0.1 1 192.168.100.255 255.255.255.255 192.168.100.222 192.168.100.222 1 224.0.0.0 240.0.0.0 10.0.0.10 10.0.0.10 3 224.0.0.0 240.0.0.0 192.168.100.222 192.168.100.222 1 255.255.255.255 255.255.255.255 10.0.0.10 10.0.0.10 1 255.255.255.255 255.255.255.255 192.168.100.222 192.168.100.222 1 255.255.255.255 255.255.255.255 192.168.100.222 2 1 Default gateway: 192.168.101.254. =========================================================================== My route configuration after connection to VPN: =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 c0 a8 de 79 01 ...... Atheros AR5006EG Wireless Network Adapter - Teefer2 Miniport 0x10005 ...02 00 4c 4f 4f 50 ...... Microsoft Loopback Card 0x160003 ...00 17 42 31 0e 16 ...... Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller - Teefer2 Miniport 0x170006 ...00 05 9a 3c 78 00 ...... Cisco Systems VPN Adapter - Teefer2 Miniport =========================================================================== =========================================================================== Active routes: Network Destination Netmask Gateway Interface Metrics 0.0.0.0 0.0.0.0 10.251.6.1 10.251.6.51 1 10.0.0.0 255.255.255.0 10.0.0.10 10.0.0.10 30 10.0.0.0 255.255.255.0 10.251.6.1 10.251.6.51 10 10.0.0.10 255.255.255.255 127.0.0.1 127.0.0.1 30 10.1.150.10 255.255.255.255 192.168.101.254 192.168.100.222 1 10.251.6.0 255.255.255.0 10.251.6.51 10.251.6.51 20 10.251.6.51 255.255.255.255 127.0.0.1 127.0.0.1 20 10.255.255.255 255.255.255.255 10.0.0.10 10.0.0.10 30 10.255.255.255 255.255.255.255 10.251.6.51 10.251.6.51 20 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.100.0 255.255.254.0 192.168.100.222 192.168.100.222 10 192.168.100.0 255.255.254.0 10.251.6.1 10.251.6.51 10 192.168.100.222 255.255.255.255 127.0.0.1 127.0.0.1 10 192.168.100.255 255.255.255.255 192.168.100.222 192.168.100.222 10 213.158.197.124 255.255.255.255 192.168.101.254 192.168.100.222 1 224.0.0.0 240.0.0.0 10.0.0.10 10.0.0.10 30 224.0.0.0 240.0.0.0 10.251.6.51 10.251.6.51 20 224.0.0.0 240.0.0.0 192.168.100.222 192.168.100.222 10 255.255.255.255 255.255.255.255 10.0.0.10 10.0.0.10 1 255.255.255.255 255.255.255.255 10.251.6.51 10.251.6.51 1 255.255.255.255 255.255.255.255 192.168.100.222 192.168.100.222 1 255.255.255.255 255.255.255.255 192.168.100.222 2 1 Default gateway: 10.251.6.1. ===========================================================================

  Read the article

• 4TB HGST SATA drive only shows 1.62 TB in Windows Server 2012

  - by user136085

  I'm using a Supermicro X9SRE-3F motherboard with the latest BIOS and 2x 4TB drives connected to the on-board SATA controller. If I set the BIOS to RAID and create a RAID 1 array, the array shows up in the BIOS as 3.6TB. However when I boot Windows (on a separate RAID 1 array), the 4TB drives show up individually in disk manager as 2x 1.62TB drives. I could use Windows 2012 to set up software RAID 1, but when I set the BIOS back to 2x individual drives, they still show up in Windows as 2x 1.62TB drives. How do I access the full capacity of these drives? Thanks, Brian Bulaw

  Read the article

• How to configure Windows Server 2008 DHCP to supply unique subnet to a remote site?

  - by caleban

  The Main site hosts the only Windows Server. Windows Server 2008 R2 Domain Controller running AD, DNS, DHCP, Exchange 2007. Remote site has no Windows server. Main site subnet is 192.168.1.0/24 Remote site subnet is 192.168.2.0/24 The Windows Server at Main site is supplying 192.168.1.0/24 via DHCP to hosts at the local site where it resides. Is it possible to configure that Windows Server to supply 192.168.2.0/24 to hosts at the Remote site and if so how? We could use the Cisco router at the Remote site to supply DHCP but if possible we'd like to use the Windows Server at the Main site to supply DHCP.

  Read the article

• USB forwarding from dom0 to domU

  - by Karolis T.

  What are my options to forward two USB connected phones to xen guest? I've read about PCI-passthrough http://www.wlug.org.nz/XenPciPassthrough, but I'm sure usb controller in the server isn't a pci card. There's device level forwarding, but I need to forward two devices, this here doesn't say how to do it: http://www.olivetalks.com/2008/02/03/usb-forwarding-on-xen-it-just-does-not-work/ Would something as simple as: usbdevice = [ 'host:xxx', 'host:yyy', ] work? EDIT: I'm now starting a bounty. This is really important for me and for other people also, hoping someone who have this resolved will be able to help.

  Read the article

• How difficult will it be to switch DHCP from Windows 2000 to our network router?

  - by MetalSearGolid

  While I know a bit about networking, I am more of a programmer, and I have never set up a DHCP server. I have always allowed a router to assign IP addresses. However, my boss has asked me to switch out our old Win2k Domain Controller and DHCP server to a new server. The catch is that he wants to just use our router to assign IP addresses rather than have the new server do it. Is this going to be more than just disconnecting the old server? And if so, are there any documents or tips anyone can help me to make the transition a bit smoother? The new server will most likely have Windows Server 2008 R2. Any advice I can get on this matter would be greatly appreciated.

  Read the article

• Terrible Performance with SATA Drives on Dell PowerEdge, steps to troubleshoot?

  - by Tom

  I had asked this question earlier and the question went missing so here it is again. Bought a DELL Poweredge 2950 to use as in-house QA Server. Disk performance is beyond terrible, 1000-4000 ms response time on the drive with our SQL Server database .mdf. Sql Server disk queue upwards of 300 at times. I'm a software guy, can anyone help me with steps to determine the issue? I don't know what RAID controller it has, how can I determine that? I'm speculating it could be BIOS issue. Perhaps the server used to have another kind of drive in it and when I added SATA the ??? buffer size is wrong??? Perhaps I chose wrong options (chose defaults) when setting up the RAID 1 arrays? I thought RAID 1 was a performance array?

  Read the article

• Active Directory replication failing with Access is Denied

  - by Justin Love

  I recently discovered that Active Directory replication started failing about a month ago. If I attempt to Replicate Now from the failing domain controller, I receive The following error occurred during the attempt to synchronize the domain controllers: Access is denied. It is between two servers at a remote site. One is Windows 2003 and the other is Windows 2000; the Windows 2000 machines is experiencing the errors. The domain is older OUR_DOMAIN style. Attempts so far: I disabled Kerberos service on the Windows 2000 server and restarted RPC and RPC locater services have expected settings HKEY_Local_Machine\Software\Microsoft\Rpc\ClientProtocols missing ncacn_nb_tcp on Windows 20003 server (added) Portqry reports okay Firewall disabled netdom resetpwd (and reboot) on Windows 2000 server.

  Read the article

• Areca 1880ix RAID hangs

  - by Dave

  Areca RAID controller ARC-1880ix-12 (firmware 1.50) hangs when on high load. My setup is: Chenbro 3U chassis Intel S5500BC mainboard Xeon 5603 CPU 16GB of RAM 12 Seagate SAS drives ST32000645SS (2 of them as hot spare, 10 as RAID10) Mellanox Infiniband HBA card This server is working as external infiniband storage for Xen VMs. When load is quite big Areca's firmware hangs - it becomes unreachable even from Areca's ethernet adapter. After resetting the server power it returns to normal operation. While Areca is hanged I can confirm that it is powered (ethernet link is active) and Infiniband HBA works Ok. Thanks in advance for any idea or suggestion where the problem might be!

  Read the article

• Why has ESXi 5.0 not used the software RAID configuration on my test server?

  - by kafka

  I've got a test server which was running WS 2008 Enterprise on the bare metal. It was correctly using the software RAID 1 configuration (2x250 GB disks which appeared as one disk), setup on the Dell Poweredge T110 (which meets compatibility requirements) without requiring any extra setup from me. (As an aside I'm fairly sure it's software RAID, as we didn't spec a hardware RAID controller, if that's of any importance in this situation). I am now testing installing ESXi 5.0 on this server to run some VMs. I've successfully installed ESXi, and imported a VM fine, but it's showing 2 x 250 GB disks available as datastores. However they should be appearing as one volume. When I boot the server, there is a RAID configuration screen you can enter, and I'm guessing this is what I'll have to do at some stage, but now need to be very careful because there is one disk which contains data that I want to be mirrored on the other disk. What is the best thing to do in this situation?

  Read the article

• Ubuntu 11.04: No Audio Output

  - by Jason George

  I installed a fresh copy of Ubuntu 11.04 earlier this week and I'm having trouble getting my audio online. It was working fine in 10.04 and all the resources I can find on troubleshooting seem to be fairly dated so I'm not sure if they apply. CMI8788 [Oxygen HD Audio] Analog Stereo Duplex Playing a WMA file shows 0.00db output when I mouse over the sound controller in the status bar. Obviously, no output from my speakers. I tried adjusting the profile, thinking I might have the wrong one. That seems to have made things worse. Where mouse over originally said something along the lines of "Oxygen HD Audio," it now reads "Dummy Output." Selecting "Test Speakers" in sound preferences crashes the dialog. Any pointers would be great.

  Read the article

• Active Directory: trouble adding new DC

  - by ethrbunny

  I have a domain with 3 DCs. One is starting to fail so I brought up a new one. All are running Win 2003. Problem: there appear to be replication issues between the 4 machines but I can't figure out what's causing this. All are registered with the DNS as identically as I can make them. How do I know there is a problem? Nagios is telling me that the other 3 DCs are having KCCEvent errors and the new machine is reporting "failed connectivity" errors. Doing dcdiag on the new machine reports: the host could not be resolved to an IP address. This seems crazy as I log into it using the DNS name. I can ping it from the other three machines using this DNS name as well. repadmin /showreps from the new machine says its seeing the other 3 machines. Doing the same from one of the older machines doesn't show the new machine. I've tried netdiag /repair numerous times. No luck. There are no firewalls running on any of the machines. If I look at Domain info via MMC (on the new machine) it appears that all the information is current. Users, computers, DCs.. its all there. Im puzzled as to what step(s) I've missed in adding this new machine. Suggestions? EDIT: dcdiag from non-working: C:\Documents and Settings\Administrator.BME>dcdiag Domain Controller Diagnosis Performing initial setup: Done gathering initial info. Doing initial required tests Testing server: Default-First-Site-Name\YELLOW Starting test: Connectivity The host 312ce6ea-7909-4e15-aff6-45c3d1d9a0d9._msdcs.server.edu could not be resolved to an IP address. Check the DNS server, DHCP, server name, etc Although the Guid DNS name (312ce6ea-7909-4e15-aff6-45c3d1d9a0d9._msdcs.server.edu) couldn't be resolved, the server name (yellow.server.edu) resolved to the IP address (10.127.24.79) and was pingable. Check that the IP address is registered correctly with the DNS server. ......................... YELLOW failed test Connectivity Doing primary tests Testing server: Default-First-Site-Name\YELLOW Skipping all tests, because server YELLOW is not responding to directory service requests Running partition tests on : Schema Starting test: CrossRefValidation ......................... Schema passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Schema passed test CheckSDRefDom Running partition tests on : Configuration Starting test: CrossRefValidation ......................... Configuration passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Configuration passed test CheckSDRefDom Running partition tests on : bme Starting test: CrossRefValidation ......................... bme passed test CrossRefValidation Starting test: CheckSDRefDom ......................... bme passed test CheckSDRefDom Running enterprise tests on : server.edu Starting test: Intersite ......................... server.edu passed test Intersite Starting test: FsmoCheck ......................... server.edu passed test FsmoCheck dcdiag from working: P:\>dcdiag Domain Controller Diagnosis Performing initial setup: Done gathering initial info. Doing initial required tests Testing server: Default-First-Site-Name\AD1 Starting test: Connectivity ......................... AD1 passed test Connectivity Doing primary tests Testing server: Default-First-Site-Name\AD1 Starting test: Replications ......................... AD1 passed test Replications Starting test: NCSecDesc ......................... AD1 passed test NCSecDesc Starting test: NetLogons ......................... AD1 passed test NetLogons Starting test: Advertising ......................... AD1 passed test Advertising Starting test: KnowsOfRoleHolders ......................... AD1 passed test KnowsOfRoleHolders Starting test: RidManager ......................... AD1 passed test RidManager Starting test: MachineAccount ......................... AD1 passed test MachineAccount Starting test: Services ......................... AD1 passed test Services Starting test: ObjectsReplicated ......................... AD1 passed test ObjectsReplicated Starting test: frssysvol ......................... AD1 passed test frssysvol Starting test: frsevent ......................... AD1 passed test frsevent Starting test: kccevent ......................... AD1 passed test kccevent Starting test: systemlog ......................... AD1 passed test systemlog Starting test: VerifyReferences ......................... AD1 passed test VerifyReferences Running partition tests on : Schema Starting test: CrossRefValidation ......................... Schema passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Schema passed test CheckSDRefDom Running partition tests on : Configuration Starting test: CrossRefValidation ......................... Configuration passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Configuration passed test CheckSDRefDom Running partition tests on : bme Starting test: CrossRefValidation ......................... bme passed test CrossRefValidation Starting test: CheckSDRefDom ......................... bme passed test CheckSDRefDom Running enterprise tests on : server.edu Starting test: Intersite ......................... server.edu passed test Intersite Starting test: FsmoCheck ......................... server.edu passed test FsmoCheck P:\>

  Read the article

• How Can I prevent a specific application from being run on a specific machine using Group Policy?

  - by Mike

  I know this is possible to do and I am working on it with limited success. I believe the Group Policy I want is "Do Not Run Specified Windows Applications" - I can enable this and add the .exe I want to the list of programs not to be run. I have tried this on my local machine by running gpedit.msc going to User Config Admin Templates System and then choosing that policy and editing and enabling it. Doing it this way verifies that it works as I could then not run the specified .exe (XenAppWeb.exe) So this is great. I have created a GPO to do the same thing in GP Management on my domain controller where we centralize this, enforced it, applied it to an OU, and put one of our machines into this OU to test it. I have let it sit there for 3 days, run gpupdate /force, and when I try to run XenAppWeb.exe on this machine, it still lets me run it fine. What can I look at to troubleshoot this? I should note that I am trying to enact this policy on Windows XP machines (Virtual Machines) Thanks, Mike

  Read the article

• Sorting out mSSD acceleration on a Acer M3-581TG

  - by PhonicUK

  I recently purchased a Acer Timeline M3 Ultra, it ships with a 500GB HDD and a 20GB mSSD to use as a cache. First thing I did when I got it was format the drives and install a clean OS (on the HDD, the mSSD has nothing on it) - but now I can't figure out how everything needs to be configured in order to use the mSSD as a cache, it just looks like a standard storage drive. I've poked around in the BIOS and there is a SATA mode setting, but it only has one option (AHCI), most of the documentation I've seen on the subject says that the SATA controller needs to be in RAID mode otherwise 'Acceleration' isn't visible in the Intel SRT menu (which for me, it isn't) I've seen a few things that suggest I just need the correct partition layout, I tried this using fdisk from a Linux LiveCD but got nowhere. Any ideas? The laptop shipped with no recovery media so I'm marginally stumped. I don't have any issue with reformatting again if required.

  Read the article

• How can I accurately determine the age of a hard drive?

  - by Todd Stout

  Yes, if it's large, heavy, and only 65 Meg in capacity, you can assume it's ancient. An RLL controller would positively indicate the drive is from antiquity. What about drives that are only 3 or 4 years old? If I know the serial number, make and model is there a public database that indicates a manufacturing date? Update: As trite as this question might seem to some, the hard drive I was looking at that precipitated this question had no obvious manufacturing date stamped on it. I realize that most do. I think the answers given are very useful to myself and others.

  Read the article

• Certain drives in RAID 5 set intermittently are not recognized

  - by hydroparadise

  I have a curious problem in that 1 (sometimes 2) drives do not get recognized in a RAID 5 set. The server is getting rather old at 5 to 6 years, but still seems to function well once the machine sees all drives. So that leaves me with three areas to consider: the motherboard, the SATA RAID card, or the individual hard drives themselves. I am leaning toward the RAID card, but have not had much dealings with RAID cards. What would cause individual drives not to be recognized in the set? If it was the card, I would think that it would be all or nothing. If it were a single drive, is it possible that it would only work sometimes? The only other thing to consider is that that they are different drives (Seagate and Western Digital) but all around 80 GB. SATA RAID controller is 3ware Escalade 8506-4LP Motherboard is a SuperMicro P4SPA+ Am open and available for more details if needed...

  Read the article

• Red Hat 5.4 slow processing

  - by yucefrizk

  I'm running Red Hat Linux 5.4 on HP DL580 server with 16 processors and 64 GB of RAM. I'm connecting to the server remotely through SSH. after entering the password, it takes time to return the command line, if I click ctrl+c during this time, I'll have the command line prompt but not the correct bash prompt (I have to run bash to pass to my correct prompt). I tried to install Apache on the server, ./configure took 4 hours to finish instead of 1 or two minutes, Oracle installation same behavior. Server Disks are mirrored using RAID controller. any idea what could be the reason of this slowness?

  Read the article

< Previous Page | 290 291 292 293 294 295 296 297 298 299 300 301  | Next Page >