Search Results

Search found 30511 results on 1221 pages for 'linux networking'.

Page 301/1221 | < Previous Page | 297 298 299 300 301 302 303 304 305 306 307 308  | Next Page >

• iMac G5 20" (First All-In-One White Screen) Cannot Connect To Internet

  - by Goober

  The Scenario I've got an iMac G5 20" (First All-In-One White Screen) PPC. It has an Airport Extreme Network card in order to wirelessly to connect to the internet. For the most part I connect using ethernet as opposed to wirelessly, but recently have had the need to connect using the wireless. The Hardware BT Home Broadband Wireless Router. iMac G5 20" From about 5 years ago (First All-In-One White Screen) The Issue Even though I know for a fact that It has connected to the internet wireslessly in the past, for some reason it can discover the wireless router, but upon entering the password it fails to connect. I have tried multiple times to no avail. I have 2 other Mac's on the network and a pc that can all connect wirelessly. However both the mac's. Question Any ideas as to why my really old iMac G5 can't connect wirelessly anymore!?

  Read the article

• Weird Network Behavior of Home Router

  - by Stilgar

  First of all I would like to apologize because what you are going to read will be long and confusing but I am fighting this issue for 3 days now and am out of ideas. At home I have the following setup 50Mbps Internet connects into a home router A 2 desktop computers connect to router A via standard FTP LAN cables including one where the cable is ~20m long. a second router B connects to router A via standard FTP LAN cable X (~20m long). several devices connect to the wireless network of router B and there are a couple of desktop computers connected to it through FTP LAN cables. For some reason computers connected to router B when it is connected via cable X have very slow Internet connection. It is like 5 times slower than what is expected. This is the actual problem I am trying to solve. Interesting facts If a computer is connected to cable X directly instead of through router B the Internet speed is just fine (up to the 50Mbps I get from the ISP). Tested with two computers. I have tried replacing router B with another router C and the problem persists. If I connect router B via another cable to the same ports with the same settings everything seems to work fine and computers connected to router B have quite fast Internet I have tested mainly via Speedtest.net but I have also achieved similar speeds when downloading a file The upload speed is quite higher than the download speed in all cases. Note that my ISP usually has higher upload speed (unless it manages to hit the 50Mbps cap) It seems like the speed when connecting through router B with cable X is reduced 4-5 times no matter what the original speed is. For example via router B I get 10Mbps speed to local servers where I get 50Mbps when connected on router A. If I use a distant server where the ISP is only able to provide 25Mbps I get 4-5Mbps on router B. WiFi is slower than LAN on both routers (which is normal) but the reduced speed is reduced proportionally for WiFi. In addition the upload speed is normally higher from the ISP and it is also reduced proportionally. I have tried two different network configurations. One where I have NAT behind NAT where router B connects to router A via the WAN port and has its own DHCP. Second where router B connects to router A via standard LAN port and has DHCP disabled. In this configuration router B serves as a switch and the Network Gateway for computers connected to router B is the internal IP address of router A. Both configurations work just fine but both manifest the reduced speed issue. pings seem to work just fine As far as I can tell none of the cables is crossed The RJ45 setup for cable X orange orange-white brown brow-white blue blue-white green green-white This is a big problem for me since cable X passes through walls and floors and is very hard to replace. I also may have gotten some of the facts wrong because I am almost going crazy with this issue and testing includes going several floors up and down the staircase. One hypothesis I came up with is that the cable is defective in such a way that the voltage from the router affects its performance. When it is connected to a computer it performs just fine but the router has less power. Related hypothesis includes the cable being affected by electricity cables in the walls when the voltage is low. (I know nothing about electricity) So any ideas what to do, what to test or what the issue may be?

  Read the article

• How to access internet from 2 laptops with data card plugged-in in one of the machine?

  - by learnerforever

  Hi, I have 2 laptops - one running Windows XP and other running Vista. Both have wifi card.I have one Reliance broadband data card. I want to be able to access internet on both the machines simultaneously using this one data card. Please help. I think, there would be many many ways to do it. I do have some linksys router but any simple quick way without any extra hardware? like we could set up p2p or WLAN between these 2 machines, because both have wifi card so we shouldn't compulsorily need any extra hardware(?) I am fine with connecting data card to either of the machines. Thanks,

  Read the article

• How can I effectively block torrenting?

  - by Chauncellor

  My WNR1000v3 is serving six people and two of them have decided that despite my warnings they're going to torrent heavily all day. Not dealing with that crap I decided to reserve their IPs and set up port blocking 1000-65535 at all times of the day. However.... looking at the log reveals that stuff is still going through. Half of the entries are saying: [LAN access from remote] from <externalIP>:16001 to 192.168.1.7:18946 Friday, Oct 12,2012 22:47:05 and half are saying: [Service blocked: BlockTorrents] from source 192.168.1.7, Friday, Oct 12,2012 22:46:26 Is this because of uPNP? Or does the 'block services' feature Netgear has only work with outgoing connections? Is there something that I'm missing? If it is indeed uPNP, how could I effectively block their torrenting without hurting everyone's use of services like Skype, Playstation Network, etc.?

  Read the article

• How can I "share" a network share over the internet to multiple operating systems?

  - by Minsc

  Hello all, We have a network share accessible through our intranet that is widely used. This share has it's own set of fine tuned permissions. I have been tasked with allowing A.D. authenticated access to this share over the internet without the use of VPN. The internet access has to mimic the NTSF permissions in place on the share. Another piece of the puzzle is that the access over the internet has to allow perusal of the share from Windows and Mac OS systems. I had envisioned a web front end that would facilitate downloading to and uploading from the share via a web browser. I'm trying to ask for some suggestions about what type of setup is necessary to achieve this. I've done loads of testing and searching for solutions but I can't seem to get anything to work as I hope. The web server that will be handing all of this is a Windows 2K8 box with IIS 7. How can I allow the users to authenticate against Active Directory when coming from the internet even when coming from a Mac system? I hope my question is not too broad, I'm sorry if I should have broken it up into multiple questions. It all is just tied together in my head. Thank you all for your time and aid.

  Read the article

• Spanning-tree setup with incompatible switches

  - by wfaulk

  I have a set of eight HP ProCurve 2910al-48G Ethernet switches at my datacenter that are set up in a star topology with no physical loops. I want to partially mesh the switches for redundancy and manage the loops with a spanning-tree protocol. However, our connection to the datacenter is provided by two uplinks, each to a Cisco 3750. The datacenter's switches are handling the redundant connection using PVST spanning-tree, which is a Cisco-proprietary spanning-tree implementation that my HP switches do not support. It appears that my switches are not participating in the datacenter's spanning-tree domain, but are blindly passing the BPDUs between the two switchports on my side, which enables the datacenter's switches to recognize the loop and put one of the uplinks into the Blocking state. This is somewhat supposition, but I can confirm that, while my switches say that both of the uplink ports are forwarding, only one is passing any real quantity of data. (I am assuming that I cannot get the datacenter to move away from PVST. I don't know that I'd want them to make that significant of a change anyway.) The datacenter has also sent me this output from their switches (which I have expurgated of any identifiable info): 3750G-1#sh spanning-tree vlan nnn VLAN0nnn Spanning tree enabled protocol ieee Root ID Priority 10 Address 00d0.0114.xxxx Cost 4 Port 5 (GigabitEthernet1/0/5) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32mmm (priority 32768 sys-id-ext nnn) Address 0018.73d3.yyyy Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/5 Root FWD 4 128.5 P2p Gi1/0/6 Altn BLK 4 128.6 P2p Gi1/0/8 Altn BLK 4 128.8 P2p and: 3750G-2#sh spanning-tree vlan nnn VLAN0nnn Spanning tree enabled protocol ieee Root ID Priority 10 Address 00d0.0114.xxxx Cost 4 Port 6 (GigabitEthernet1/0/6) Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Bridge ID Priority 32mmm (priority 32768 sys-id-ext nnn) Address 000f.f71e.zzzz Hello Time 2 sec Max Age 20 sec Forward Delay 15 sec Aging Time 300 sec Interface Role Sts Cost Prio.Nbr Type ------------------- ---- --- --------- -------- -------------------------------- Gi1/0/1 Desg FWD 4 128.1 P2p Gi1/0/5 Altn BLK 4 128.5 P2p Gi1/0/6 Root FWD 4 128.6 P2p Gi1/0/8 Desg FWD 4 128.8 P2p The uplinks to my switches are on Gi1/0/8 on both of their switches. The uplink ports are configured with a single tagged VLAN. I am also using a number of other tagged VLANs in my switch infrastructure. And, to be clear, I am passing the tagged VLAN I'm receiving from the datacenter to other ports on other switches in my infrastructure. My question is: how do I configure my switches so that I can use a spanning tree protocol inside my switch infrastructure without breaking the datacenter's spanning tree that I cannot participate in?

  Read the article

• Block P2P traffic on a Linksys router WRT54G with tomato firmware

  - by Kami

  Hi, I'm running a small wireless network (6 to 10 users) on a Lynksys WRT54G with tomato firmware sharing an internet connection. I don't want the users to download files with bittorrent (mainly used) and other p2p apps. I've also found some solutions about lowering p2p traffic priority using QoS. I really need to BAN p2p traffic. Does anyone know how to setup some rules to deny that kind of traffic ? I've tried to setup an Access Restriction Rule: But it's not working at all ...

  Read the article

• How can ICS in Windows 7 be managed via command line, scripts, config files, etc.?

  - by Skya

  I've been using ICS successfully for years, but now I'm looking for a way to control it through something else than the GUI in Control Panel\Network and Internet\Network Connections - Connection Properties: I want to do everything that the encircled checkbox does, without touching the GUI. But what does the checkbox do? Microsoft don't provide specific information and the most helpful forum post I've found is from 2003. Assuming that some of the advice is still valid, I've come to the conclusion that ICS is broken down into 6 parts that have to be set up individually: the sharedAccess service interface settings firewall rules a static route dnsproxy autodhcp I've already learned that the service can be started/stopped with the command net start/stop sharedAccess and that netsh is a good tool for changing the interface settings and the firewall rules. But I don't understand how ICS handles routing and DNS. All hosts in my network are configured statically, so I don't care much about autodhcp. Thanks for your help! EDIT: I've spent the whole day scanning through ProcMon and I've seen reads/writes to both the registry and the filesystem and it is difficult to determine what parts of it actually make ICS work. I'm trying to look for an API instead. I'm looking into this right now, but I still want to know more about the inner workings.

  Read the article

• Does VPN connection on virtual machine bypass host VPN?

  - by Daniel Valland Torgrimsen

  I wanted to see if i could channel my traffic trough two vpns, so as an experiment i set up a windows xp virtual machine in virtualbox (using NAT shared network setting), connected the host pc(windows 7) to a vpn, and then the virtual machine to another vpn. this seams to work fine. However, my question is, is the traffic sent trough both vpn servers, or is the virtual machines vpn bypassing the host machines vpn connection? thanks.

  Read the article

• Kickstart installation from USB -- Kickstart location

  - by dooffas

  After managing to get a Fedora ISO to rebuild successfully (for a USB stick) after adding a kickstart file (http://serverfault.com/questions/548405/), I now have an issue with locating the kickstart file on the USB media. When this is done from a CDROM you can simply kickckstart by adding this parameter to boot: linux ks=cdrom This will kickstart (providing the kickstart file is named ks.cfg and is in the root of the disk). Now, obviously this will be different for the USB drive, so from my research, I assumed that this line would do the job: linux ks=hd:sdb1:/ks.cfg Evidently this does not work. I get an error informing me this drive is already mounted and cannot be remounted. EDIT: Actual error message: mount: /dev/sdb1 is already mounted or /run/install/tmpmnt0 busy Warning: Can't get kickstart from /dev/sdb1:/ks.cfg To test that the syntax was correct I placed the kickstart file on another USB stick and loaded the same command to grab ks.cfg from the new location: linux ks=hd:sdc1:/ks.cfg This does work (providing USB sticks are mounted in order, boot - sdb1, kickstart - sdc1). The install will kickstart and complete the install with no issue. Obviously having to use 2 pen drives is somewhat frustrating and unreliable. Is there a way around this?

  Read the article

• No network connectivity for my CentOS 6 installed in VMWare Fusion in MacOSX Lion

  - by gilzero

  I installed CentOS 6.2 (CentOS-6.2-x86_64-minimal.iso) with VMWare Fusion(Version 4.1.2). (Not with EasyInstall). I am using MacOSX Lion, connect to internet via WIFI. The centos installed does not have network connectivity. *How may I configure it to connect to wifi? * Thanks for any help. Below is screenshot of ifconfig: With the setting Network Adapter, I tried both NAT and Bridged WiFi.

  Read the article

• Can't connect to wireless router anymore due to data rate problem

  - by Jay White

  I was playing around with my wireless router, and switched the mode to a fixed mode B. Now< I can no longer assoicate to the AP. Windows does not give any particular error message, but with wireshark I see that the returned error is that the client does not support the necessary data rate. My wireless card is type n, and it is set to mode a/b/g compatible. I tried setting ot to just b, however this made no difference. How can I set the data rate of my card so that I can connect again to my AP? I would prefer not to just reset the device, as there has been some configuration done that would be a pain to redo, and as well I do not have the ISP password handy. Regardless I would like to understand this situation better.

  Read the article

• tcpdump selective acknowledgements question

  - by wlaus

  Hi All, I eventually sometimes watch most initial tcp connection attempts like this: tcpdump -nn -Z somepcapuser not src host (12x.x5.109.xxx or 62.75.160.xxx ) and not (port 9001 or 443 or 8080 ) and tcp[tcpflags]&(tcp-syn) !=0 and not tcp[tcpflags]& (tcp-ack) !=0 or icmp this works pretty well to quickly identify oddness so far. However, I now have a question on the following output: 03:53:52.227884 IP 203.81.166.20.53786 62.75.160.xxx.80: S 846930886:846930886(0) win 61690 "<"mss 1460,nop,nop,sackOK,opt-178:f04700000000,nop,wscale 4"" I wonder what the marked portion means, haven't seen that before. Thanks for help wlaus

  Read the article

• Server Names Inside Private Network

  - by thyandrecardoso

  Our office has a private network, where any requests on a (pre-determined) public IP are forwarded to a private IP inside said network. On that private IP, we've got a server running several services, including HTTP servers, and SCM systems. We only control our private network, having no control on the public IP configuration. We bought a domain name, and pointed it to that public IP, so people can access our services from the outside. But, when inside the office, people can't use that DNS name, because the server and any other hosts inside the network share the same public IP! For desktops, inside the office network, dealing with names is really easy: one entry on the hosts file and we're done. However, for laptops, that keep going in and out, and need to access services inside the office, the naming is really annoying. I don't know the "standard" process for dealing with these kind of situations. I've considered installing BIND in the office, and make people configure their wireless and wired connections to use that DNS server. What is the correct approach in this situation? If using BIND (or any other DNS server) is the answer, how should I configure it so that people inside the office can use it to get our custom names, and get forwarded to the ISP DNS when trying to reach the internet?

  Read the article

• Two network cards in one Windows 7 PC

  - by Martin

  Hi, I've upgraded from Vista to Windows 7. On Vista I used to run one network card (Intel 82566DC -2 Gigabit) for my internet which was connected to a Dovado USB mobile broadband router connected to a 3G modem. The IP setup on the card is set on DHCP. The second card (3com Ethernet link) was used to connect to our town's local WUG (wireless user group) and all worked fine. Now the problem I have with Windows 7 is that when I connect to the internet with the (Intel) first card, the internet work fine but as soon as I connect the second card to the wug my internet drops. If I then disconnect the first card (internet one) and try to connect to the wug it works. It seems that the two cards are fighting each other. Is there maybe something I can do to fix the problem? As you probably can gather from this post is that I am not an expert on PC's so please if you do answer do I in simple terms. :) Thanks, Martin

  Read the article

• cisco 6500 crash enabling netflow

  - by bleomycin

  Hello everyone, i have a cisco 6503 running IOS 12.2(33)sxi5 and i'm trying to enable netflow. Following the instructions here http://www.manageengine.com/products/netflow/help/cisco-netflow/cisco-ios-netflow.html enabling for interface vlan 3, shortly after ip flow-export version 5 console outputs: CPU_MONITOR-6-NOT_HEARD: CPU monitor messages have not been heard for 30 seconds crashlog here: http://pastebin.com/Niv2H8xD it then writes a crash log and reloads the router. Has anyone else experienced anything like this before? Here is my running config prior to adding the options in the above link: http://pastebin.com/AgNb1ahG Thank you for any help!

  Read the article

• Rename a Network Printer win Win 7

  - by Alex

  Seems this is a common question but the answers regularly miss the point. I have a server. Server has some printers connected. Server has all drivers for x32 & x64 OS PLUS ALL DEFAULTS set. Server also manages print queue. I have many workstations, all need to use the printers. All NEED to have drivers print queue and DEFAULTS propagated from server. Now.... When I add the printers on the workstations, I get: "ABC Printer on SERVER123" I need something less long - just "ABC Printer" So how? Tip: Please don't show me how to change the name of your locally installed printer. I know how to do this - I am particularly interested in shared printers that look like "ABC Printer on SERVER123" Tip: Installing the driver with a local port wont cut it because then I loose the server propagated defaults, the driver updates and I need to run around with driver disks/confuse trembling users with hard things like choosing drivers. I am happy for a hack if there is no official way to do this in the group policy.... I tried looking in HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Printers on the workstation machines but those are only local printers :( I can see the network printer details on the workstations here: HKEY_USERS[Some GUID]\Printers\Connections But there is nothing obvious like a description string... Can anyone help with this?

  Read the article

• Windows Server 2008 R2, weird intermittent outgoing connection issues, & Hyper-V Virtual Network

  - by brizz

  My provider says that they run an 'unfiltered' network, so it's not a network issue. Not entirely convinced...but they aren't being very helpful. Basically two days ago started having issues with DNS completely stop working for anywhere between 2-20minutes. This happens roughly every 1-2 hours at least once. I later then found that I am unable to ping ANY external IP address when this is going on. So it's not a DNS issue. Whats even more odd is when this is going on, I STAY connected via RDP, and I can access webpages, etc that are on the server when I access from my home computer. Have tried disabling the firewall--no fix. Have checked Event viewer, the only thing that is there is a warning that DNS has stopped working. I have made no changes/updates to the server. The only thing I have done is add an IP address (don't think it has anything to do with the problem, but wanted to mention everything). Any help/insight/suggestions on how to go about debugging would be much appreciated! update: I am also running Hyper-V, and a virtual network. I just tried pinging (when I have issues), from a Hyper-V machine--and it works, when the main server doesn't.

  Read the article

• allow SSH to bypass VPN on OSX mavericks, openvpn, pf

  - by zycho42

  My home computer connects to the internet through an OpenVPN connection. However, I would like to be able to connect to my home computer from outside over ssh. Ssh is set up and working, but when I connect to the vpn ssh is only accessible from inside my home network. I figure what's going wrong is my router forwards incoming ssh connections to my mac, but then my mac replies over the vpn, so the connection from outside times out. I've got pf set up for a couple of other things, but I can't figure out how to let the ssh replies bypass the vpn using pf. I've come across other solutions that use ip tables, routing tables and rules, but I can't figure out how to set that up on mavericks. I've been searching for this for a while now but I haven't found a working solution. Any help would be greatly appreciated!

  Read the article

• what is uninstall procedure for software installed via "make install" on CentOS 6.2

  - by gkdsp

  I installed OCILIB on my CentOS 6.2 server some time ago, and now I want to install a newer version. The vendor requires an uninstall, but doesn't provide instructions. I'm guessing that's because it's trivial for people with a Linux background. http://orclib.sourceforge.net/doc/html/group_g_install.html If I installed this software using: step 1: # ./configure --with-oracle-headers-path=/usr/include/oracle/11.2/client64 --with-oracle-lib-path=/usr/lib/oracle/11.2/client64/lib step 2: # make step 3: # su root step 4: # make install step 5: # gcc -g -DOCI_IMPORT_LINKAGE -DOCI_CHARSET_ANSI -L/usr/lib/oracle/11.2/client64/lib -lclntsh -L/usr/local/lib -locilib conn.c -o conn How would I go about uninstalling this? I tried following this http://www.cyberciti.biz/faq/delete-uninstall-software-linux-commands/ but nothing was found on my disk using rpm -qa *oci* or yum list *oci*. Maybe since it wasn't installed with yum or rpm then I shouldn't expect either of these to find it. Are there generic instructions for uninstalling software on Linux that I could use, or do the instructions really depend on the specific software? Any help much appreciated.

  Read the article

• The physical working paradigm of a signal passing on wire.

  - by smwikipedia

  Hi, This may be more a question of physics, so pardon me if there's any inconvenience. When I study computer networks, I often read something like this in order to represent a signal, we place some voltage on one end of the wire and the other end will detect the voltage and thus the signal. So I am wondering how a signal exactly passes through wire? Here's my current understanding based on my formal knowledge about electronics: First we need a close circuit to constrain/hold the electronic field. When we place a voltage at somewhere A of the circuit, electronic field will start to build up within the circuit medium, this process should be as fast as light speed. And as the electronic field is being built up, the electrons within the circuit medium are moved, and thus electronic current occurs, and once the electronic current is strong enough to be detected at somewhere else B on the complete circuit, then B knows about what has happend at A and thus communication between A and B is achieved. The above is only talking about the process of sending a single voltage through wire. If there's a bitstream and we need to send a series of voltages, I am not sure which of the following is true: The 2nd voltage should only be sent from A after the 1st voltage has been detected at B, the time interval is time needed to stimulate the electronic field in the medium and form a detectable electronic current at B. Several different voltages could be sent on wire one by one, different electronic current values will exists along the wire simutaneously and arrive at B successively. I hope I made myself clear and someone else has ever pondered this question. (I tag this question with network cause I don't know if there's a better option.) Thanks, Sam

  Read the article

• I just ordered 70/10 internet service, and need a new router I think?

  - by data_jepp

  Before I had 25/5 service and the N standard router did just fine. Now it doesn't do the job. Online speedtest reads at 82 so I have the line. But my laptop is getting less than 30 in my room. My laptop has the following WiFi card: http://www.intel.com/content/www/us/en/wireless-products/centrino-advanced-n-6205.html What is this talk about 2.4 and 5GHz? Can my laptop be connected at once over both bands? And would that let me use the full 70Mb over Wi-Fi?

  Read the article

• Synergy on macbook with osx mavericks wifi connection

  - by user332956

  I'm trying to set up Synergy with my macbook pro running OS X 10.9.3 as a client and my Windows 7 desktop as a server. I'm having some pretty bad connection problems though when I try to use my mac. Every couple seconds the mouse or the keyboard will stop working entirely then come back. I ran some tests and found that the ping from my desktop to my mac would be very high every third ping or so(1000+ ms) or sometimes even time out. If I ping my desktop from my mac the pings are all reasonably low. I believe that this is a power saving feature of Mavericks and I have found a way to get around it by continually pinging my router on my mac, keeping my wifi card from going to sleep. I'm using this right now to type this up with synergy and have had zero issues. Has anyone else ran into this issue and found a better solution? So far, I think my best bet would be to buy an ethernet adapter but I'd rather not have yet another cable running across my desk.

  Read the article

• Cisco VPN disconnects after 5 seconds with error 422

  - by Marius

  I'm trying to connect to my university's server with VPN using Cisco VPN Client version 5.0.04, but after 5 seconds it disconnects with the error message 422: Lost contact with the secure gateway. Check your connection. From my research on the net it seems this could be because it tries to find my IP, and finds out that this is 127.0.0.1. Then 5 seconds later it discovers that I have a new IP (my actual IP), and it disconnects because I'm not allowed to change IP. Does anyone know how I could fix this, or if there is another reason i get this error? Update I looked through the log, and found this error, which confirms what I thought, except it gets the correct IP first, then changes it to localhost. 87 18:56:53.250 08/24/09 Sev=Warning/3 CM/0xA3100027 Adapter address changed from 149.171.237.25. Current address(es): 127.0.0.1.

  Read the article

• how to use winpcap to send EAPOL packets on windows 7 with wireless card?

  - by caimengru0807

  I want to implement a 802.1X wireless client on Windows 7 using PEAP/MSCHAPv2. The 802.1X protocol is a data link layer protocol, it uses the EAPOL protocol to encapsulate the packets. I use the WinPcap to send and receive the EAPOL packets, however I fail to do it with the wireless NIC. It can work fine to send the EAPOL packets use wired NIC. It can also work fine to send the EAPOL packets on Windows XP using wireless NIC. So what's wrong with it on Windows 7?

  Read the article

< Previous Page | 297 298 299 300 301 302 303 304 305 306 307 308  | Next Page >