Search Results

Search found 13930 results on 558 pages for 'dev center'.

Page 332/558 | < Previous Page | 328 329 330 331 332 333 334 335 336 337 338 339  | Next Page >

• Force local IP traffic to an external interface

  - by calandoa

  I have a machine with several interfaces that I can configure as I want, for instance: eth1: 192.168.1.1 eth2: 192.168.2.2 I would like to be able to forward all the traffic to one of these local address trhough the other interface. For instance, all requests to an iperf, ftp, http server at 192.168.1.1 are not just routed internally, but forwarded through eth2 (and the external network will take care of re-routing the packet to eth1). I tried and looked at several commands, like iptables, ip route, etc... but nothing worked. The closest behavior I could get was done with: ip route change to 192.168.1.1/24 dev eth2 which send all 192.168.1.x on eth2, except for 192.168.1.1 which is still routed internally. The goal of this setup is to do interface driver testing without using two PCs. I am using Linux, but if you know how to do that with Windows, I'll buy it!

  Read the article

• How can I stop my laptop display from flickering when I connect my TV?

  - by Lord Torgamus

  I have a laptop with an HDMI output port running Vista, and an HDTV with HDMI input ports. The laptop is set to extend its desktop onto a second monitor. When I connect the computer to the TV with an HDMI cable, my laptop screen usually flickers rapidly. Most of the time it lasts for about 30 seconds, but sometimes it lasts for several minutes and once in a while it doesn't happen at all. It wouldn't be so bad except that the cursor moves back to the center of the laptop screen with each flicker, so I can't really do anything until the machine decides it's ready to calm down. I haven't been able to find any pattern at all for the causes or duration of the flickering. It doesn't seem to matter what programs the laptop is running when I connect it to the TV, whether I enable the extended display before or after I connect the TV or which HDMI port/cable I use. What could be causing this, and how can I make it go away?

  Read the article

• After installing Windows Phone 8 SDK, Connectify doesn't work

  - by Pratyush Nalam

  Today I installed Windows Phone 8 SDK from the official site. After installing and a couple of restarts (it restarted the PC to enable Hyper-V), I opened Connectify. I use Connectify Hotspot to connect my iPod to the internet as I have an ethernet connection and no wireless router. The problem is that now, Connectify doesn't show WiFi in Share Over. The attached screenshot shows this. Previously, before I installed the SDK, it would show Ethernet and Wi-Fi. I would select WiFi and share my internet. Now, this is completely screwed. EDIT: I found out that the Microsoft Virtual Wi-Fi Miniport Driver has got disabled and I am not able to enable it again. Please advise. Please advise on what to do Hardware: Windows 8 Pro with Media Center, Apple MacBook Pro 9,1 15 inch Mid-2012 (non retina)

  Read the article

• How to determine the used size of device associated's buffer

  - by dubbaluga

  Hi, when mounting a device without the "sync" option, e. g. by invoking the following: mount -o async /dev/sdc1 /mnt a buffer is associated with a device to optimize (speed) read/write operations. Is there a way to determine the size of this buffer? Another question that comes into my mind is, if it's possible to find out how much of it is used currently. This can be interesting to determine the time it would take to "sync" or "umount" slow devices, such as flash-based media. Thanks in advance for your answers, Rainer

  Read the article

• How to move unseen windows => Cannot access my application after switching monitors

  - by Stephane Rolland

  I switch monitors really often: At work I have a very poor computer, and gpu too, which is bad at keeping its configuration, resolution and monitor position between each reboot. Both monitor are different size and resolution. When doing that I often have applications that were on one of the monitors that remember their last position opened... so now they are unseen, at screen coordinates I cannot access. I know there is a shortcut that can access the move functionnality of a window. Could you remind it to me. Do you have other trick to center all opened windows into the visible screens ?

  Read the article

• Detecting/Reactivating serial port that becomes inactive on Ubuntu Linux 10.10

  - by Tom

  I am using a usb2serial port to communicate with some old equipment (using my code built upon the boost asio library - I think my code is fine because it works almost all of the time). Every so often (maybe once every few days) the communication stops with my device with no error at all - the device just does not respond. I then restart my computer and everything is fine again. Does anyone know where I can start to analyse this problem? My serial port loads up fine (in /dev/ttyUSB0) and the boost library does not throw an error. The device just does not respond. If I restart the device no change - only when I restart my pc does it make a difference. I have also tried unplugging and replugging the usb connector. Does anyone know what gets cleared in the reboot (w.r.t the serial device) or what I can probe when the problem happens again (rather than just restarting with hope)

  Read the article

• Need to get a file written to a floppy.

  - by dboarman-FissureStudios

  I asked this question over on SO. I have tried dd if=kernel.sys of=/dev/fd0 bs=512 seek=1 to get this file to write to the floppy. It is a kernel shell that must be written to the sector immediately following the bootsector of a disk to boot the PC. No matter what I've tried, for some reason, kernel.sys is not writing to the floppy. I know the bootstrap loader is being written and executed. However, it cannot find the kernel to load the shell. Any ideas on what I am doing wrong? I mean, really, how is it so difficult to get this file written to a floppy? OpenSUSE 11.2

  Read the article

• Netinstalling CentOS if the gateway is in a different subnet

  - by James Lawrie

  I have a KVM host (A) running a virtual machine (B). They each have their own external IP address and the networking is setup using bridging between eth0 and br0 on A. B uses eth0, with A being the gateway. The problem is that the two external IP addresses are on different subnets (different /8s in fact) so by default, B claims it cannot reach A (Network Unreachable). I can resolve this by adding a static route on B: echo "any host gateway_ip dev eth0" > /etc/sysconfig/static-routes Modifying /etc/init.d/networking to reload the gateway after applying static routes (I only added the final line before fi): if [ -f /etc/sysconfig/static-routes ]; then grep "^any" /etc/sysconfig/static-routes | while read ignore args ; do /sbin/route add -$args done route add default gw "${GATEWAY}" fi If I then restart networking, it comes online. How can I do this (or work around it some other way) prior to the system being installed, ideally inside an Anaconda kickstart file?

  Read the article

• How Do I make an Acer T230H Touchcreen work on Ubuntu 9.10?

  - by N Rahl

  I've done this so far: sudo nano /etc/udev/rules.d/99-touchscreen.rules And added: SUBSYSTEM=="usb", ATTRS{idVendor}=="0408", ATTRS{idProduct}=="3000", SYMLINK+="usb/quanta_touch" SUBSYSTEM=="input", KERNEL=="event*", ATTRS{idVendor}=="0408", ATTRS{idProduct}=="3000", SYMLINK+="input/quanta_touch" sudo service udev restart then the instructions here: http://ubuntuforums.org/showpost.php?p=8932808&postcount=36 And then added to my xorg conf: Section "InputDevice" Identifier "Acer T230H" Driver "hidtouch" Option "SendCoreEvents" "true" Option "ReportingMode" "Raw" Option "Device" "/dev/usb/quanta_touch" Option "PacketCount" "13" Option "OpcodePressure" "852034" Option "OpcodeX" "65584" Option "OpcodeY" "65585" Option "CalibrationModel" "1" Option "CornerTopLeftX" "0" Option "CornerTopLeftY" "0" Option "CornerTopRightX" "1920" # 1920 for 23" Option "CornerTopRightY" "0" Option "CornerBottomLeftX" "0" Option "CornerBottomLeftY" "1080" # 1080 for 23" Option "CornerBottomRightX" "1920" # 1920 for 23" Option "CornerBottomRightY" "1080" # 1080 for 23" Option "CornerScreenWidth" "1920" # 1920 for 23" Option "CornerScreenHeight" "1080" # 1080 for 23" EndSection Section "ServerLayout" Identifier "Touchscreen" InputDevice "Acer T230H" "SendCoreEvents" EndSection And restarted. And the touchscreen does nothing. Any ideas?

  Read the article

• Are these components compatible and are there any significant bottlenecks?

  - by Tom Gullen

  I'm trying to buy a new pc, for software dev and a bit of gaming. I already have a 500gb HDD , and a PCI sound card I want to use as well. Is all this stuff compatible, and will it all work together and are there any significant bottlenecks? Case, Mobo and PSU "Primo Motion" AMD 880G DDR3 Ready Barebones (Socket AM3) http://www.overclockers.co.uk/showproduct.php?prodid=FS-268-OK&groupid=43&catid=1817&subcat= SSD 64GB Crucial RealSSD C300 64GB 2.5" SATA 6Gb/s Solid State Hard Drive http://www.overclockers.co.uk/showproduct.php?prodid=HD-007-CR&groupid=1657&catid=1660&subcat=1668 CPU AMD Phenom II X6 Six Core 1090T Black Edition 3.20GHz (Socket AM3) http://www.overclockers.co.uk/showproduct.php?prodid=CP-266-AM&groupid=701&catid=6&subcat=1944 RAM 8GB Corsair Vengeance 8GB (2x4GB) DDR3 PC3-15000C9 1866MHz Dual Channel Kit http://www.overclockers.co.uk/showproduct.php?prodid=MY-292-CS&groupid=701&catid=8&subcat=1387 Graphics XFX ATI Radeon HD 5770 1024MB GDDR5 PCI-Express Graphics Card http://www.overclockers.co.uk/showproduct.php?prodid=GX-149-XF

  Read the article

• Is there a simple Load Balancer app for development environment on Windows?

  - by djangofan

  Does there exist a simple Load Balancer app for development on Windows? I am running a pair of JBoss 5.x instances in a cluster on a single machine. Normally , this configuration is load balanced by a nice hardware load balancer but I am wondering if there is a simple piece of software to enable load balancing in my Eclipse dev environment. Basically, for example, I want a load balancer running on port 11111 that round-robins between the 2 clustered JBoss instances on ssl ports 8443 and 8543 . (or http port if thats not possible) I know that Glassfish has a built-in load balancer but I can't use Glassfish. One idea I have is to try to setup a separate instance of Tomcat with the "balancer" web app. Im trying that now... not sure if it will work... and its a complicated setup and I wish there was something really easy.

  Read the article

• EBS+RAID10+XFS slower than EBS+RAID10+EXT3 using MySQL?

  - by Johann Tagle

  We're currently using EC2 with 16 EBS volumes in RAID10 configuration for our MySQL data. I know some people don't recommend to put EBS volumes to RAID but that's not what I'm concerned about at the moment. Current format is ext3, but we're experimenting with moving to xfs, given many reports that it is faster. However, we're actually experiencing a performance degradation when the partition was converted to xfs - a benchmark run with inserts, updates, selects and deletes was more than 10 seconds slower using xfs. Any idea what could be the problem? Below is the fstab entry (really only changed ext3 to xfs). Database tables are innodb and we are using innodb_file_per_table. /dev/mapper/vg_data-lv_data /data xfs noatime 0 0 Thanks.

  Read the article

• Connecting my XBOX 360 to home network

  - by patrick

  I am trying to set up my XBOX 360 as a Windows Media Center Extender. I input the code as shown on the XBOX screen, but I get the error message: "Cannot Set Up Extender." This means that the Extender was found (there's a separate error msg for extender not found), however it can't be set up. Windows points me to this page which tells me to change my router settings to enable multicast and UPnP. My router doesn't have those specific settings but I did open all ports for the XBOX. What is odd about this problem is that it did work, then I restarted my computer and didn't change any settings, and now it doesn't work. I guess something did change, but I can't figure out anything else to try after opening all ports. I'm running Windows 7 and the router is fairly recent (I bought it about six months ago) so it should be able to handle this. The router firmware is up to date.

  Read the article

• Exim queue in WHM

  - by Xobb

  Hi fellas, I've got the centos server with WHM. The mail server is exim. I need exim put all messages in queue and not sending directly.Though I've added the queue_only option to exim configuration and the messages are collected in the queue now. Afterwards I've found out that someone is calling exim -q to process the queue every once in a while. I've found the following cron job: 0 6 * * * /scripts/exim_tidydb > /dev/null 2>&1 which I beleive has been used to process the exim queue. Also I suspect that script was installed alongside with WHM. Surely I've commented it out and was expecting everything to work just fine. But that didn't happen. I still get the exim queue processed once in a while. Am I missing anything? What may cause my exim queue to process? Here is cat /etc/exim.conf | grep queue queue_only deliver_queue_load_max = 3 Thanks

  Read the article

• Netboot Debian (wheezy) from NFS v4

  - by bara

  Is it possible to boot Debian Wheezy from NFS v4? Bootwing with NFS v3 works just fine. NFS v4 not. This is in my /etc/exports: /nfs 192.168.100.0/24(ro,sync,insecure,no_root_squash,no_subtree_check,fsid=0) /nfs/root 192.168.100.0/24(ro,nohide,sync,insecure,no_root_squash,no_subtree_check) /nfs/root/www contains the root of the webserver. The commandline is: rootfstype=nfs4 root=/dev/nfs4 nfsroot=192.168.100.1:/root/www fails with mount call failed - server replied: Permission denied. Mounting from the busybox in the initrd fails: mount -t nfs4 192.168.100.1:/nfs/root/www /root mounting .. failed: Invalid argument Do I need to modify the initrd?

  Read the article

• Trouble editing ~/.bash_profile: -bash: $'\r': command not found

  - by Dave

  I installed CygWin on Windows 7. Using Notepad, I edited my ~/.bash_profile file to add on to the PATH variable … PATH="${PATH}:/cygdrive/c/apache-ant-1.8.2/bin" Now, when I SSH in to my Windows machine, I get this error … -bash: $'\r': command not found -bash: $'\r': command not found -bash: $'\r': command not found -bash: $'\r': command not found -bash: $'\r': command not found -bash: /home/dev/.bash_profile: line 39: syntax error: unexpected end of file and my PATH is not set. Anyone know how I can correct this?

  Read the article

• Linux Software RAID: How to fsck on hard drive?

  - by Rick-Rainer Ludwig

  We have a Linux server running with Software RAID1. We see some issues in /var/log/messages like: unreadable sector. I want to perform a complete fsck on the drive to get some more information, but a fsck /dev/md0 brings a clean due to the Software RAID layer in between. How can I check the real hard drive? Do I need to disassemble the whole RAID? How do I deal with the inconsistency in the partition due to the additional Software RAID header? Does anyone have a good idea for this?

  Read the article

• zabbix monitoring mysql database

  - by krisdigitx

  I have a server running multiple instances of mysql and also has the zabbix-agent running. In zabbix_agentd.conf i have specified: UserParameter=multi.mysql[*],mysqladmin --socket=$1 -uzabbixagent extended-status 2>/dev/null | awk '/ $3 /{print $$4}' where $1 is the socket instance. From the zabbix server i can run the test successfully. zabbix_get -s ip_of_server -k multi.mysql[/var/lib/mysql/mysql2.sock] and it returns all the values However the zabbix item/trigger does not generate the graphs, I have created a MACRO for $1 which is the socket location {$MYSQL_SOCKET1} = '/var/lib/mysql/mysql2.sock' and i use this key in items to poll the value multi.mysql[{$MYSQL_SOCKET1},Bytes_sent] LOGS: this is what i get on the logs: 3360:20120214:144716.278 item [multi.mysql['/var/lib/mysql/mysql2.sock',Bytes_received]] error: Special characters '\'"`*?[]{}~$!&;()<>|#@' are not allowed in the parameters 3360:20120214:144716.372 item [multi.mysql['/var/lib/mysql/mysql2.sock',Bytes_sent]] error: Special characters '\'"`*?[]{}~$!&;()<>|#@' are not allowed in the parameters Any ideas where the problem could be? FIXED {$MYSQL_SOCKET1} = /var/lib/mysql/mysql2.sock i removed the single quotes from the line and it worked...

  Read the article

• Strategy to allow emergency access to colocation crew

  - by itsadok

  I'm setting up a server at a new colocation center half way around the world. They installed the OS for me and sent me the root password, so there's obviously a great amount of trust in them. However, I'm pretty sure I don't want them to have my root password on a regular basis. And anyway, I intend to only allow key-based login. On some cases, though, it might be useful to let their technical support log in through a physical terminal. For example, if I somehow mess up the firewall settings. Should I even bother worrying about that? Should I set up a sudoer account with a one-time password that will change if I ever use it? Is there a common strategy for handling something like this?

  Read the article

• How to Install PCRE Development Headers on Mac OSX

  - by martincarlin87

  I just upgraded my MacBook Pro to Mavericks and my local Ruby on Rails development environment isn't running straight off the bat, when I visit localhost I see It works! and remembered I needed to start Phusion Passenger, so when I run passenger start it checks all the requisites and fails when it gets to the PCRE Development Headers: * Checking for PCRE development headers... Found: no It tells me to go to http://www.pcre.org/ to download them so I downloaded 8.33 from here which went to my Downloads folder, so I unzipped it, cd'd to the folder and ran: ./configure make make install Then cd'd back to my rails app directory on my Desktop and re-ran passenger start but it's still the same. Tried a new Terminal window but that didn't make any difference. I must have done this before to get my dev environment working but can't seem to solve it this time. I also tried brew install pcre but it says Warning: pcre-8.33 already installed.

  Read the article

• FreeBSD: Samba performance over GBit-Ethernet

  - by Axel Gneiting

  I'm using a FreeBSD NAS with RAID-Z. I can read ~300MB/s from the ZFS disks to /dev/null on the box, but only get about 50MB/s over GBit-Ethernet with SMB to Windows 7 (Samba 3.5.6). Both systems have Intel-PCIe-NICs and are connected directly. Samba is configured to use AIO and I already tried to tune TCP/IP: kern.ipc.maxsockbuf=16777216 net.inet.tcp.sendspace=1048576 net.inet.tcp.recvspace=1048576 net.inet.tcp.sendbuf_max=8388608 net.inet.tcp.recvbuf_max=8388608 net.inet.tcp.delayed_ack=0 Any ideas what's causing the bottleneck? I think the link should handle 100 MB/s easily.

  Read the article

• The previous system shutdown at xxxx was unexpected

  - by m.edmondson

  For the past two nights we had a remote server shutdown unexpectedly. When rebooted we get the following message: Event Type: Error Event Source: EventLog Event Category: None Event ID: 6008 Date: 16/02/2011 Time: 09:10:43 User: N/A Computer: WELPLAN-1 Description: The previous system shutdown at 07:27:32 on 16/02/2011 was unexpected. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: db 07 02 00 03 00 10 00 Û....... 0008: 07 00 1b 00 20 00 42 02 .... .B. 0010: db 07 02 00 03 00 10 00 Û....... 0018: 07 00 1b 00 20 00 42 02 .... .B. Obviously this message doesn't help much, but what does all the hexadecimal mean? Will it help me track down the problem? Any pointers as to where to look?

  Read the article

• How to completely remove a wireless network setup from vista?

  - by 3d1l

  To remove a wireless connection setup I basically go to (network and sharing center) then select (manage wireless network) and then from the list of wireless networks I right click on the one that I want to remove and select (remove network) from the drop down menu. Problem is that when I go to define the wireless network again the system said that the network connection already exist so it seems that even when the wireless network definition is not longer display in the connections list, Vista keeps the configuration somewhere. So How can I be sure that a particular wireless network has been completely removed?

  Read the article

• Electricity in VAIO laptop ports while plugged in

  - by SRbH

  I have VAIO E series (SVE) laptop. While charger plugged in, touching VGA/HDMI/USB port metal casing gives me burning sensation. So, i checked it with voltmeter and i found that while plugged in there is presences of DC +1.0 V. Same case with my friend's VAIO E Series (VPCEH). Service center says this is normal. But i do not believe them as it is not the case with Dell Inspiron. Please let me know if you are facing same problem with VAIO and is it hazardous to devices which i connect to these ports (like HDD, LED, etc)?

  Read the article

• How do you test if a PCI slot is working - motherboard diagnostic software?

  - by Adam

  I suspect that my motherboard is bad, and that my PCI-E slot is not working. I have a Gigabyte motherboard that had a Hauppage 2250 working fine in the PCI-E slot for many months. However - recently - would not get TV channels that I used to get --- until finally Media center cant detect any channels at all. Got a new tuner card (ATI 350 card) - cant detect any channels. The cable signal is good - I have it connected directly to a TV - all channels come in clear. SO that is why I suspect a motherboard problem. Are there any motherboard diagnostic scanner utilities that can verify I need a new motherboard

  Read the article

< Previous Page | 328 329 330 331 332 333 334 335 336 337 338 339  | Next Page >