Search Results

Search found 19471 results on 779 pages for 'network troubleshooting'.

Page 332/779 | < Previous Page | 328 329 330 331 332 333 334 335 336 337 338 339  | Next Page >

  • Can't connect to Windows Server 2008 shared folders via VPN connection

    - by Pearl
    I set up an VPN connection on my 2008 server using RRAS. The VPN seems to work fine. I can connect from outside the network. I am also able to establish a remote access connection via the VPN-IP. However, I can't access my shared folders. After connecting to the VPN I can ping the server, but it is not shown in my networks. using \ip or \server-name doesn't work either, cannot be found. I checked ipconfig and this is what I found regarding the VPN: DNS-Suffix: Description: test Physical Adress: DHCP activated: No Auto-Config: Yes IPv4-Adress: 192.168.2.114 Sub: 255.255.255.255 Standard-gateway: DNS-Server: 192.168.0.1 NetBIOS: activated To clarify my IP-situation: server is connected to router with 192.168.0.x, the test-client is in an external network connected to a router with 192.168.1.x, server-client connection is using static ips with 192.168.2.x Can anyone help me with this one? The VPN should be ok since I am able to establish remote access.

    Read the article

  • Strongswan and OpenVPN together

    - by cmorgia
    I have an host in Amazon EC2 which is configured with an OpenVPN Access Server. The only client to this server is acting as a gateway from a private network. I installed StrongSWAN 5 on the same host to allow windows 7 and iOS clients to connect using IPSEC. Both services works but what I cannot figure out is how to configure StrongSWAN to consider the OpenVPN tunnel endpoint as the only gateway available to clients. Basically I want all the traffic that comes from IPSEC clients to be entirely forwarded to the OpenVPN tunnel. The remote OpenVPN client that is exposing the private network has forwarding enabled and appropriate masquerading configured. The only missing point is to have the OpenVPN tunnel as the gateway for IPsEC clients

    Read the article

  • hp pavilion g6 1250 wireless problems

    - by Ahmed Kotb
    i have tried using ubuntu 10.04 and ubuntu 11.10 and both have the same problem the driver is detected by the additional propriety drivers wizard and after installation , ubuntu can't see except on wireless network which is not mine (and i can't connect to it as it is secured) there are plenty of wireless networks around me but ubuntu can't detect them and if i tried to connect to one of them as if it was hidden connection time out. the command lspci -nvn | grep -i net gives 04:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) iwconfig gives lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off i guess it is something related to Broadcom driver .. but i don't know , any help will be appreciated UPDATE: ok i installed a new copy of 11.10 to remove the effect of any trials i have made i followed the link (http://askubuntu.com/q/67806) as suggested all what i have done now is trying the command lsmod | grep brc and it gave me the following brcmsmac 631693 0 brcmutil 17837 1 brcmsmac mac80211 310872 1 brcmsmac cfg80211 199587 2 brcmsmac,mac80211 crc_ccitt 12667 1 brcmsmac then i blacklisted all the other drivers as mentioned in the link the wireless is still disabled.. in the last installation installing the Brodcom STA driver form the additional drivers enabled the menu but as i have said before it wasn't able to connect or even get a list of available networks so what should i do now ? the output of command rfkill list all rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no

    Read the article

  • CentOS Failover Cluster - SIOCADDRT: No such process (when adding a loopback)

    - by Steve Rolfe
    I'm trying to configure two web servers for a load balancing server. The load balancing aspect works fine (it sees both server, kills 'em if it needs to, and seems to direct traffic fine). The only issue is with the servers looping: /etc/sysconfig/network-scripts/ifcfg-lo:0 DEVICE=lo:0 IPADDR=<Virtual IP> NETMASK=255.255.255.255 ONBOOT=yes NAME=loopback Everytime I try a "service network restart" I get a SIOCADDRT: No such process when loading the loopback interface. Anyone have an idea what's causing this?

    Read the article

  • Can I setup a link SQL server connection between servers on different networks?

    - by Glenn Slaven
    We have a production SQL server hosted offsite at a hosting company, and we have a staging environment within our own network. We want to be able to setup a SQL job that copies content from a table on the staging server to prod on a regular basis, and I think we need to setup a linked server connection to do this. What do I need to get the hosting company to do to allow us to set this up? We have RDP access to the production servers, I just need to know what network and security configurations need to happen from the hosting company's perspective so I can ask them to do it.

    Read the article

  • Architect Day Artifacts

    - by Bob Rhubart
    In the last eight days the Oracle Technology Network Architect Day tour has stopped in Dallas,  Anaheim (Disneyland, to be precise) , and at Oracle HQ in Redwood Shores,  CA. I was on-scene for the Dallas event, where I pulled a TMZ-style ambush on Chris Benedict from the Oracle Enterprise Solutions Group to capture this short video.     The other presenters escaped. But the slide decks from several of the presentations are now available on Slideshare:  IT Optimization: Reduce Data Center Costs and Set the Foundation for Future Growth as presented by Alan Levine, Oracle Enterprise Architect Senior Director Implementing Applications with SOA and Application Integration Architecture as presented by Vish Gaitonde, Director, Ecosystem Strategy, Application Integration Architecture Application Grid: Platform for Virtualization and Consolidation of Your Java Applications as presented by Sam Shah, Director, SOA and Integration, Oracle Enterprise Solutions Group Infrastructure Consolidation and Virtualization as presented by Steve Bennett, also a Director with the Oracle Enterprise Solutions Group Security in a Cloudy Architecture as presented by Geri Born, Security Specialist with the Oracle Enterprise Solutions Group I’ll post more Architect Day presentations as soon as I track them down. A special thank you to Oracle ACE Directors Jordan Braunstein, Billy Tong, and Kai Yu, who were on hand in Dallas, and to fellow ACE Directors Basheer Khan and Floyd Teter for their participation in the Anaheim event.  (Floyd and his iPad came through again, allowing me to record the Anaheim panel discussion via Skype while sitting in my home office in Cleveland.) That audio, as well as audio from the panel discussion and a roundtable from the Dallas event, will be available soon as ArchBeat podcast programs. If you attended one of these events, a big thanks. Your active participation, your questions and input, are what these events are all about.  As new cities are added to the tour, we expect more of the same from the OTN architect community. And did I mention that the food is free? So stay tuned… del.icio.us Tags: oracle,otn,enterprise architecture,enterprise architect,archbeat,arch2arch,architect day Technorati Tags: oracle,otn,enterprise architecture,enterprise architect,archbeat,arch2arch,architect day   Cross-posted to the Oracle Technology Network Blog

    Read the article

  • Event ID 8021 The browser was unable to retrieve a list of servers from the browser master

    - by Ash
    We have a LAN where workstations are randomly losing network connectivity for brief moments of time. The workstations can also take a long time to login to the domain. During our troubleshooting we have found an error log on a few Windows 7 workstations: Warning BROWSER 8021 The browser was unable to retrieve a list of servers from the browser master \\random-pc on the network \Device\NetBT_Tcpip_{BBABCDE9-D8A0-4399-93F2-492FE0848B12}. The data is the error code. What do these errors mean? What computers should have the Computer Browser service enabled, workstations and/or servers? The environment is a mix of Windows 7 & Windows XP workstations on a Windows Server SBS 2011 SP1 domain.

    Read the article

  • How to set up server/domain name correctly in hosts file with HTTPS

    - by Byakugan
    I am trying to do local network and I am using these kind of types of network. 1) Main server which connects to internet with static IP 2) Second computer connected to first one locally with address like 192.168.0.2 - when I write this address to address line it is like i wrote localhost in original main server - so it should show my local web browser etc ... It has domain name this IP and connected router for it ... example www.domain.com so I added to my main server hosts file (linux powered) lines like these: 192.168.0.2 domain.com www.domain.com It was working ok when I entered my domain name in local computer it showed my site ... But after some time I added HTTPS cerfiticate and added this line to my apatche server: Redirect permanent / https://www.domain.com/ And now it does not work even when i add something like this to my hosts file: 192.168.0.2 https://www.domain.com So any idea how do do this thing work? Thank you.

    Read the article

  • DNS updating issue

    - by Will
    Hey guys, I'm new to serverfault so please excuse me if I sound a tad nub. I work in an environment that is kinda peace mealed together, and I honestly don't know how it works. I'm new to the IT field and am still in school. When I replace a PC I rename the old one to mo-o-pcname and give the new one the proper name of mo-pcname (mo is a location thing we use so it really doesn't apply to the problem.) The new PC will function on the network; it will have the ability to access network resources (printers, file shares, etc) and it will have the ability to get out to the internet. However I can no longer ping the machine. It would appear as if the DNS (A) record is not getting updated or something. Like I said I'm kinda new to the field and just trying to work through this problem. Thanks for your help.

    Read the article

  • How do I configure custom routes when an interface is configured?

    - by ManicDee
    Other Superuser questions have addressed the issue of adding custom routes to access e.g.: multiple networks of a corporate network through one interface, while accessing the Internet through another interface. So assuming that I have a script to add specific routes when en0 is configured, and a separate script to add specific routes when en1 is configured, is there some way I can trigger those scripts to run automatically when Mac OS X/Darwin starts and configures those interfaces? Back in my Linux days, it was possible to add an option in /etc/network/interfaces along the lines of: iface eth0 inet dhcp up /usr/local/sbin/eth0-routes-up Is there something similar for Mac OS X?

    Read the article

  • Oracle RDBMS Server 11gR2 Pre-Install RPM for Oracle Linux 6 has been released

    - by Lenz Grimmer
    Now that the certification of the Oracle Database 11g R2 with Oracle Linux 6 and the Unbreakable Enterprise Kernel has been announced, we are glad to announce the availability of oracle-rdbms-server-11gR2-preinstall, the Oracle RDBMS Server 11gR2 Pre-install RPM package (formerly known as oracle-validated). Designed specifically for Oracle Linux 6, this RPM aids in the installation of the Oracle Database. In order to install the Oracle Database 11g R2 on Oracle Linux 6, your system needs to meet a few prerequisites, as outlined in the Linux Installation Guides. Using the Oracle RDBMS Server 11gR2 Pre-install RPM, you can complete most of the pre-installation configuration tasks. which is now available from the Unbreakable Linux Network, or via the Oracle public yum repository. The pre-install package is available for x86_64 only. Specifically, the package: Causes the download and installation of various software packages and specific versions needed for database installation, with package dependencies resolved via yum Creates the user oracle and the groups oinstall and dba, which are the defaults used during database installation Modifies kernel parameters in /etc/sysctl.conf to change settings for shared memory, semaphores, the maximum number of file descriptors, and so on Sets hard and soft shell resource limits in /etc/security/limits.conf, such as the number of open files, the number of processes, and stack size to the minimum required based on the Oracle Database 11g Release 2 Server installation requirements Sets numa=off in the kernel boot parameters for x86_64 machines Please see the release announcement for further details and instructions. Also take a look at Ginny Henningsen's "How I Simplified Oracle Database Installation on Oracle Linux" article on the Oracle Technology Network for a general description on how to perform the installation of the Oracle Database on Oracle Linux. While the article refers to Oracle Linux 5 and the former "oracle-validated" package, the steps for Oracle Linux 6 are still very similar (we're looking into updating that article for Oracle Linux 6).

    Read the article

  • How to start a task before networking?

    - by user1252434
    I've written an upstart task that modifies /etc/network/interfaces. (Actually a file sourced into it.) Which start on condition do I need to declare to let my task run before any networking jobs? I've tried start on starting networking, but that's apparently too late. When I log in after booting I can see that the changes were written, but obviously they are not used: the new config states a static IP, but the boot process waits for a non-existing DHCP server (old config) to time out. I've also tried start on starting network-interface INTERFACE=eth0, which didn't work either. IIRC there was an error in the log that the change couldn't be written. Background: I need a VM template that can be cloned and the clones configured through a script. Among other settings, I need to give them a static IP address to access them from the host. I use guestfish to write a config file to one of the virtual disks and let a script apply these settings to the system. I don't want that disk to contain an actual system settings file. I can't modify /etc directly, because that disk is shared (copy-on-write/diff) among the clones and guestfish apparently doesn't support that type of image. I could also let them use DHCP and setup a server that assigns IP by MAC, but I'm afraid of the complexity. I could also add just another virtual disk for configuration files, but if possible I'd prefer to store settings directly on the system disk image. Used software: Ubuntu Server 12.04, VirtualBox. The configuration modifier is a self written ruby script.

    Read the article

  • How to connect my Android to my Laptop wirelessly , to stream data between the two?

    - by Deepun
    I want to stream data from my Laptop PC to my Android phone using TCP or UDP by creating sockets in both the phone and the laptop, but it has to be done wirelessly. How do I connect them to stream the data ? I thought creating an ad-hoc wireless network from my laptop and connecting to it using my Android would work. But my Android is not detecting the ad-hoc network. Is there any other way how I can connect the two ? I downloaded this software called 'connectify' and created a wifi hotspot on my laptop, and successfully connected the two. But will I be able to stream data to my device using this connection ? Can simple direct Bluetooth connection help me in creating sockets in both phone and laptop and stream the data ?

    Read the article

  • Ideas for campus Internet Login mechanism?

    - by miCRoSCoPiCeaRthLinG
    Hello, I work at this university and I'm seeking an effective solution for an internet login mechanism. We have a leased-link at our campus, which is shared by both staff & students. All systems (desktops + laptops + handhelds) connect to the internal network via wifi and can then get onto the net. However, a local govt. regulation requires us to keep track of individual internet usage and hence we need a solution (pref. free / opensource) that'll enable us to implement some sort of an authentication mechanism once a user hooks onto the network. One requirement is that the software should be able to authenticate either against LDAP or some other custom user database (MySQL based) or both. Can anyone suggest any such software or mechanism? Most of our servers are Linux based... so something that runs off such a platform will be good. Thanks, m^e

    Read the article

  • Windows 2003 DNS updates from ISC DHCP server

    - by wolfgangsz
    We have a very mixed network, with most clients being Debian Lenny, the rest Windows XP/Vista/7. The network itself is split into two segments (for technical reasons) called "corporate" and "engineering". On the "corporate" side all clients get their IP addresses from a Windows DHCP server and the dynamic updates into the Windows DNS work just fine. On the "engineering" side, clients get their IP addresses from a linux machine running the standard ISC DHCP server. Although this server is configured to do dynamic DNS updates, they actually don't work. Anybody got any advice on how to fix this? Please note: dynamic updates from the clients directly into the DNS would work, but are not an option for us. So this is strictly on how make this work from an ISC DHCP server to a Windows DNS server.

    Read the article

  • Proxification rulte for System process

    - by kseen
    I'm trying to configure Microsoft Visual Studio 2010 remote debugging and ran into issue: while connecting to remote computer running MSVSMON, client computer sends SYN request for connection. It makes it under the System process (as I see it in TCPView). As every network apps should be configured to use proxy in our network, I'm trying to add devenv.exe to proxification rules to make its traffic goes thru LAN's proxy server. It doesn't help. So my question is how can I make that low-level-system traffic will go through local area network proxy server?

    Read the article

  • Slow internet using Arch Linux

    - by GZaidman
    after a week or so of using Arch Linux I cant access the internet - it takes around 5 mins to load google (most of the other websites just give me a timeout), pacman's downloading speed range between 5-2Kbs, and pinging google takes around 9Kms. I'm connected using wireless network (wifi card is Intel Ultimate 6300 and router is Edimax 6524n). Every other Windows machine that's connected to the network (and even the T410 running Windows) is fine, so the problem lies in Linux. So far, i checked the resolv.conf file (my router ip address is listed), and the hosts file (pretty much default), and I disabled the ipv6 module. None of that helped. PS: i'm using NetworkManager (but the problem still occurs when connecting using wicd) running on Gnome3. Thanks in advance for any help you can provide! EDIT: something really strange happens whenever I ping google: i get an unknown host 'google.com', but the bit rate from the card jumps at the exact second I ping google (so far, the bit rate jumped to 54Mb/s from 1Mb/s over the course of 4 pings).

    Read the article

  • VirtualBox networking problem, host XP, guest Debian

    - by Silma
    Hi, I'm trying to set up a development environment in a virtual machine on my laptop, with debian os. I have both lan and wlan available on the host machine, yet I can't connect to the internet using either. As I said the host OS is windows XP and the guest OS will be the latest Debian, we downloaded the business card net install so we need internet access from the beginning, besides we need the virtual machine to be visible on the local network (for my fellow developers). We tried host-only networking, NAT, bridging, with proxy (the local network uses a proxy to connect to the internet) and without proxy, nothing seems to work. What else can we do? Thanks a lot.

    Read the article

  • ASA 5510 Need to filter traffic log events to my iPhone

    - by drpcken
    For some reason I cannot update apps or download apps to any ios devices on my network (tried both iphone and ipads). When I'm at home on my own network everything works fine. This started about a week ago. I've configured my iphone with a static IP address and even used 4.2.2.2 as my dns to rule out that the issue is with my DNS Server. I'm looking at the SYSLOG in ASDM (Cisco ASA 5510) but Im not sure it is providing me enough info. It seems to be showing ACL blocks on my public ip address, but not individual client IP's, so I can't see whats going on. How can I setup a way to filter any incoming/outgoing traffic to my iPhone's static IP and try and troubleshoot this?

    Read the article

  • Top ten security tips for non-technical users

    - by Justin
    I'm giving a presentation later this week to the staff at the company where I work. The goal of the presentation is to serve as a refresher/remidner of good practices that can help keep our network secure. The audience is made up of both programmers and non-technical staff, so the presentation is geared for non-technical users. I want part of this presentation to be a top list of "tips". The list needs to be short (to encourage memory) and be specific and relevant to the user. I have the following five items so far: Never open an attachment you didn't expect Only download software from a trusted source, like download.com Do not distribute passwords when requested via phone or email Be wary of social engineering Do not store sensitive data on an FTP server Some clarifications: This is for our work network These need to be "best practices" tips for the end-user, not IT policy We have backups, OS patches, firewall, AV, etc, all centrally managed This is for a small business (less than 25 people) I have two questions: Do you suggest any additional items? Do you suggest any changes to existing items?

    Read the article

  • Proper use of disk to disk to tape backup using de-duplication and LTO5

    - by Michael
    I currently have ~12TB of data for a full disk to tape (LTO3) backup. Needless to say, it's now requiring over 16 tapes so I'm looking at other solutions. Here is what I've come up with. I'd like to hear the community's thoughts. Server for Disk-to-Disk BackupExec 2010 Using De-duplication Technology 20+TB worth of SATA drives LTO5 robotic library connected via SAS 1Gbps NIC connected to network What I envision is doing a full backup of my entire network which will initially take a long time over the 1Gbps NIC but once the de-duplication kicks in backups should be quick. I will then use the LTO5 to make disk to tape backups and archive those accordingly. What does everyone think? Any faster way of doing the initial full backup over the 1Gbps NIC? What will be my pain points? Is there a better way of doing what I'm trying to achieve?

    Read the article

  • Cannot connect Ubunto to Windows pc either direction

    - by Frank A
    New to ubuntu and really struggling with this. I want to connect to my old windows XP Pc on our home network. Searching for solutions gets complicated as at one level you are told use Connect to Server. I set to Windows Share, type in server IP address.. ... I get "Failed to retrieve share list from server" Demo on Youtube worked with no problem. Other advice in ask ubuntu is you need to install samba. Did that but nothing seems to happen when I try and run it other than it asking for admin password. (How do you tell what is running on Ubuntu?) So I try the other direction Windows XP to Ubuntu. I made the ubuntu directory within home frank shared and tried various combination such as \ipaddress\home\frank but just "The folder you entered does not appear to be valid. Please choose another." My entire data only drive is shared in Windows and no problems accessing that from other Win XP boxes on our network There are no alerts in Windows firewall, Ubuntu Firestarter did block but changed that to allowed... or so I thought. In firestarter I had set up Inbound traffic policy 192.168.1.1/24. And since then it has added the ip address of the win pc twice. So, I am in a state of confusion not knowing whedre to turn next so thought Ask Ubuntu :)

    Read the article

  • getting input/output error from NFS client on RHEL5

    - by Andrew Watson
    i have two RHEL5 boxes on a private network together (192.168.2.0/24) and I am trying to export a file system from one to the other but I keep getting the following error: mount.nfs: Input/output error on the client side I see this output: mount: trying 192.168.2.101 prog 100003 vers 3 prot tcp port 2049 mount: trying 192.168.2.101 prog 100005 vers 3 prot tcp port 960 and on the server side I see this: Sep 20 14:14:32 omicron mountd[18739]: authenticated mount request from 192.168.2.87:635 for /srv/nfs/web (/srv/nfs/web) but that's all. I opened up iptables so that the whole 192.168.2.0/24 network is allowed to communicate freely but the public side is locked down to 22,80 etc.... any ideas?

    Read the article

  • Looking for a fiber optic "switch" or "router" for home use

    - by Shrout1
    The gist of my question: What is a "fiber optic" switch called? I.E. a layer 2 ethernet switch that uses fiber TX and RX connections and sends layer 2 network traffic between the fiber strands that are connected. Can someone purchase a dedicated fiber switch that does not have copper ethernet ports? What is the current average price of a device like this? Not necessarily looking for product endorsements, just information Might not make sense to go this route if it is too cost prohibitive What type of fiber connector is used for terminating a fiber strand into a jack on the wall? Can fiber be "patched" using two jacks and a "patch" cable? Is signal loss a concern with the longest runs at 100-200ft, a patch cable and media converters? The full story: My parents had unterminated fiber optic cable and terminated Cat5e run throughout their home when it was built in 2004. 10 years later the Cat5e isn't providing the throughput that my father needs to accomplish multiple streams of HD and fast system backups throughout the house. He can't reach gigabit speeds across the distance of the Cat5e runs. We are both interested in terminating the fiber connections and using them as high speed "backbones" to copper switches in each room of the house. It would be easy to attain gigabit speeds (or better, eventually) using the fiber. I have searched and searched for a "fiber optic switch" or "fiber optic router" and cannot find the correct term to describe this piece of hardware. We can use fiber media converters at the end points of each connection, however it would be nice to have a "patch panel" set up in the network closet in the basement that has fiber connections on it and switches the ethernet streams between the connections/systems in the house. Each fiber media converter costs between $50-$100 a piece... After 10 or so terminated connections it might make sense to find a piece of hardware that does not require media converters. That would depend upon the cost of this hardware Somewhat unrelated, if we are able to route between these fiber strands successfully, what is the physical connector type used in a jack on the wall? Just like RJ45 has a wall outlet (depicted below): What is the fiber optic equivalent of this? In the interim could we "patch" a couple fiber strands together in the network closet? Would signal loss be of concern with a run length of 100-200 feet, a patch cable and two media converters? If that would work then it could be used until the funds are available for more.

    Read the article

  • DNS servers via RA in IPv6

    - by glglgl
    Some time ago, RFC 6106 was created, which states how a router tells the clients about the DNS server to be used. It is a new standard, it has to be implemented, which needs time etc. I'm courious about the need for it: wouldn't have it been better to define a "globally valid" anycast address for DNS? Queries would be sent to this address and would be promoted along the default route until there is a host which claims to be responsible for it. In an enterprise network, that would be a central DNS server (or even more, on really big companies); in a SOHO network, it would either be the router or the DNS server of the ISP, in a root server hosting data center, it would be the DNS of the hoster, etc. What do I see wrong here? Do I have a wrong view of the anycast concept?

    Read the article

< Previous Page | 328 329 330 331 332 333 334 335 336 337 338 339  | Next Page >