Search Results

Search found 24933 results on 998 pages for 'arch linux'.

Page 390/998 | < Previous Page | 386 387 388 389 390 391 392 393 394 395 396 397  | Next Page >

  • Fedora 15: em1 recently dissapeared and hostapd no longer serves internet to wirelessly connected devices

    - by Daniel K
    I have a laptop running hostapd, phpd, and mysql. This laptop uses an Ethernet connection to connect to the internet and acts as a wireless access point for my workplace's wifi devices. After installing some software and reconnecting my Ethernet elsewhere, my "em1" device is no longer present and wirelessly connected devices can no longer reach the internet. The software I recently installed is: pptp, pptpd, and updated some fedora libraries. I have also recently moved my desk and laptop to another location and thus had to reconnect the Ethernet elsewhere. Wifi devices no longer have access to the internet. Wirelessly connected devices are able to successfully log into the laptop, showing full strength, correct SSID, and uses the proper password. However, when I tried to connect to a site like google, the request times out. The device "em1" also no longer appears on my machine. Running: # ifup em1 will give me the following output: ERROR : [/etc/sysconfig/network-scripts/ifup-eth] Device em1 does not seem to be present, delaying initialization. And running: # dhclient em1 has the following output: Cannot find device "em1" When I run # dmesg|grep renamed, I get the following: renamed network interface eth0 to p4p1. I've tried to connect to the internet through p4p1 directly from the laptop and was successful. However, my wireless devices connected to my laptop are not able to connect to the internet. I have uninstalled pptp and pptpd using # yum erase ... but the problem still persists. To install pptp I used: # yum install pptp To install pptpd I did the following: # rpm -Uvh http://poptop.sourceforge.net/yum/stable/fc15/pptp-release-current.noarch.rpm # yum install pptpd To update my fedora libraries I used: # yum check-update # yum update EDIT: Running # route produces the following results: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.11.200.1 0.0.0.0 UG 0 0 0 p4p1 10.11.200.0 * 255.255.252.0 U 0 0 0 p4p1 172.16.100.0 * 255.255.255.0 U 0 0 0 wlan0

    Read the article

  • How to show a warning message when entering a folder?

    - by Valter Henrique
    I don't know if this is possible, but, I have a folder which I would like to show some warning message when the user enters in it. In my case would say that the folder could be deleted without previous warning to save some disk space. I already create a file inside the folder with the warning message: WARNING! ########################################################################################################################################################## Please, be advised, that the folder /company-backup/amazon-s3 can be deleted without previous WARNING to save disk space as the INFRASTRUCTURE TEAM judge necessary. Best regards, Infrastructure Team. ########################################################################################################################################################### Is that possible ? Any idea ?

    Read the article

  • Server not configured error

    - by Ivan Slaughter
    I'm using Plesk 8.3 for my hosting account. Server said : Server Default page If you see this page it means: 1. hosting for this domain is not configured or 2. there's no such domain registered in Plesk What you can do: * Using Plesk, you can create domains with web hosting on a single physical server. what left on my setting?

    Read the article

  • Incorrect durations mp4 file created by ffmpeg (avconv)

    - by Ruslan Sharipov
    Example usage: avconv -i rtmp://maps.lo.ufanet.ru/live/10e227922b473e91f37474fa084107af -vcodec copy -an -sn -map 0 -f segment -segment_format mp4 -segment_time 60 -y %05d.mp4 avconv version 0.8.3-6:0.8.3-1+b1, Copyright (c) 2000-2012 the Libav developers built on Jun 15 2012 13:54:35 with gcc 4.7.0 HandShake: client signature does not match! Metadata: height 480.00 remote_addr: sdp_session {sdp_session,0, {sdp_o,"-","1289703354974145","1289703354974145",inet4, "10.1.12.99"}, "Media Presentation", {inet4,"0.0.0.0"}, {0,0}, [{"control","*"},{"range","npt=0.0 start 30400239.52 timeshift_duration 319250.58 timeshift_size 120000.00 width 640.00 [flv @ 0x1d36a40] Estimating duration from bitrate, this may be inaccurate Input #0, flv, from 'rtmp://maps.lo.ufanet.ru/live/10e227922b473e91f37474fa084107af': Duration: N/A, start: 0.000000, bitrate: N/A Stream #0.0: Video: h264 (Baseline), yuvj420p, 640x480 [PAR 1:1 DAR 4:3], 1k tbr, 1k tbn, 2k tbc Output #0, segment, to '%05d.mp4': Metadata: encoder : Lavf53.21.0 Stream #0.0: Video: libx264, yuvj420p, 640x480 [PAR 1:1 DAR 4:3], q=2-31, 1k tbn, 1k tbc Stream mapping: Stream #0:0 -> #0:0 (copy) Press ctrl-c to stop encoding ^Cframe= 9566 fps= 36 q=-1.0 Lsize= -0kB time=318.25 bitrate= -0.0kbits/s video:30348kB audio:0kB global headers:0kB muxing overhead -100.000071% Received signal 2: terminating. Result: serafim@yard:~/video2$ ls 00000.mp4 00001.mp4 00002.mp4 00003.mp4 00004.mp4 00005.mp4 Now try to play the files in the player, such as VLC. And that's what we get: the first fragment (00000.mp4) played well, no problems, but the second (00001.mp4 and beyond) starts the bug manifests itself, namely the file 00001.mp4 first 60 seconds black screen, but since 61 seconds starts playing the video. Attachments: https://dl.dropbox.com/u/760901/rtmp_and_mp4.zip How to get rid of the delay with black screen at the beginning of the segments? Maybe ffmpeg to pass parameters, or third-party software is able to correct the obtained segments mp4?

    Read the article

  • Why assign write and execute permissions to a group when executing web scripts?

    - by PeanutsMonkey
    If I have a script that is to be executed by the nobody user, why is there a need to assign group write and execute permissions. For example in the article at http://www.zzee.com/solutions/unix-permissions.shtml, it notes that the permission 755 should be assigned to scripts on a web server. I understand that the user nobody is treated as others and as the owner of the script I would like full permissions. Am I missing something?

    Read the article

  • CPU Affinity on ARM processors

    - by dsljanus
    I am using some RaspberryPI boards for a data acquisition system. They are nice boards, with plenty of community support around them, but they are really slow. I am thinking of gradually replacing them with ODROID multicore boards, with the Samsung Exynos processors. I have some experience using taskset to set CPU affinity on my servers because I am always running Node.js applications that are by definition single threaded. Now, is it possible to do this on an ARM board? I do not see why it would not in theory, but I have doubts over how well it is going to work. Does anyone have experience with this kind of hack? Also, I would appreciate any comments about ARM CPUs and how they differ from x86.

    Read the article

  • SASL - Plaintext password not accepted - Encrypted works

    - by leviathanus
    I have a very strange issue! SASL does not work properly, as it does not accept plain-text passwords (like Outlook sends them) Oct 2 10:35:09 srf cyrus/imap[4119]: accepted connection Oct 2 10:35:09 srf cyrus/imap[4119]: badlogin: [217.XX.XXX.140] plaintext [email protected] SASL(-1): generic failure: checkpass failed Now I switch to "Encrypted password" in Thunderbird. I have the same issue as Outlook above on Thunderbird if I turn on "Plain Password"): Oct 2 10:40:40 srf cyrus/imap[14644]: accepted connection Oct 2 10:40:41 srf cyrus/imap[14622]: login: [217.XX.XXX.140] [email protected] CRAM-MD5 User logged in Same with Postfix: Without Oct 2 10:42:48 srf postfix/smtpd[17980]: connect from unknown[217.XX.XXX.140] Oct 2 10:42:48 srf postfix/smtpd[17980]: warning: SASL authentication failure: cannot connect to saslauthd server: Permission denied Oct 2 10:42:48 srf postfix/smtpd[17980]: warning: SASL authentication failure: Password verification failed Oct 2 10:42:48 srf postfix/smtpd[17980]: warning: unknown[217.XX.XXX.140]: SASL PLAIN authentication failed: generic failure With "Encrypted password": Oct 2 10:45:27 srf postfix/smtpd[21872]: connect from unknown[217.XX.XXX.140] Oct 2 10:45:28 srf postfix/smtpd[21872]: 50B3A332AAB: client=unknown[217.XX.XXX.140], sasl_method=CRAM-MD5, [email protected] Oct 2 10:45:28 srf postfix/cleanup[21899]: 50B3A332AAB: message-id=<[email protected]> Oct 2 10:45:28 srf postfix/qmgr[6181]: 50B3A332AAB: from=<[email protected]>, size=398, nrcpt=1 (queue active) Oct 2 10:45:28 srf postfix/smtpd[21872]: disconnect from unknown[217.XX.XXX.140] Config: /etc/imapd.conf:sasl_mech_list:LOGIN PLAIN CRAM-MD5 and /etc/postfix/sasl/smtpd.conf:mech_list: LOGIN PLAIN CRAM-MD5 I have no idea where to dig. Please advise.

    Read the article

  • "iostat" command different in two equal machines

    - by Oz.
    We have several machines on Amazon (ec2) of the type c1.xlarge with 8 cpus, running the Amazon AMI. Details on the machine: 7 GB of memory 20 EC2 Compute Units (8 virtual cores with 2.5 EC2 Compute Units each) 1690 GB of instance storage 64-bit platform I/O Performance: High API name: c1.xlarge One out of the several machines is showing a high load average, since we have run the last yum upgrade a couple of weeks a go. We did not yet update the other machines, and everything looks normal on them. The strange thing is that the top command not showing any hint for the cause of the load. CPUs are - 4.8%us, 1.1%sy, 0.0%ni, 94.1%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st. Mem is about 1.5GB free. Any idea what could it be, or where else can we check? iostat command on the proper machine: avg-cpu: %user %nice %system %iowait %steal %idle 8.97 0.03 4.46 0.19 0.14 86.23 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvdap1 1.60 0.69 55.38 587620 47254184 xvdfp2 2.64 1.10 61.04 934786 52091056 xvdfp4 0.86 0.19 41.72 163866 35601920 xvdfp1 4.37 36.59 73.89 31220810 63051504 xvdfp3 8.03 7.08 94.63 6045402 80749184 iostat command on problematic machine: avg-cpu: %user %nice %system %iowait %steal %idle 9.29 0.04 5.55 0.26 0.11 84.74 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn xvdap1 2.13 3.34 68.85 246244 5077888 xvdfp1 7.60 74.31 104.88 5480362 7734840 xvdfp3 13.22 73.67 125.00 5433386 9218600 xvdfp4 1.11 0.76 65.08 55762 4799248 xvdfp2 4.16 3.31 99.17 243818 7313264 Many thanks for the help.

    Read the article

  • How to interpret IOZone results?

    - by homer5439
    Here are the resuts of running IOZone on an ext3 filesystem on an LVM volume residing on a SAN LUN (it was ran with 5 parallel processes). "Throughput report Y-axis is type of test X-axis is number of processes" "Record size = 4 Kbytes " "Output is in Kbytes/sec" " Initial write " 81628.55 " Rewrite " 83354.72 " Read " 115595.02 " Re-read " 119306.09 " Reverse Read " 47684.20 " Stride read " 10011.09 " Random read " 16751.27 " Mixed workload " 5659.77 " Random write " 1661.85 " Pwrite " 36030.83 Now this is all nice and dandy, but my question is: how do I know whether the values are as good as they could be or there is something to tweak (and if so, what?) The actual usage I will have for that Logical Volume is to act as virtual disk for a VM.

    Read the article

  • What info is really useful in my iptables log and how do I disable the useless bits?

    - by anthony01
    In my iptables rules files, I entered this at the end: -A INPUT -j LOG --log-level 4 --log-ip-options --log-prefix "iptables: " I DROP everything besides INPUT for SSH (port 22) I have a web server and when I try to connect to it through my browser, through a forbidden port number (on purpose), I get something like that in my iptables.log Sep 24 14:05:57 myserver kernel: [xx.xx] iptables: IN=eth0 OUT= MAC=aa:bb:cc SRC=yy.yy.yy.yy DST=xx.xx.xx.xx LEN=64 TOS=0x00 PREC=0x00 TTL=54 ID=59351 DF PROTO=TCP SPT=63776 DPT=1999 WINDOW=65535 RES=0x00 SYN URGP=0 Sep 24 14:06:01 myserver kernel: [xx.xx] iptables: IN=eth0 OUT= MAC=aa:bb:cc SRC= yy.yy.yy.yy DST=xx.xx.xx.xx LEN=48 TOS=0x00 PREC=0x00 TTL=54 ID=63377 DF PROTO=TCP SPT=63776 DPT=1999 WINDOW=65535 RES=0x00 SYN URGP=0 Sep 24 14:06:09 myserver kernel: [xx.xx] iptables: IN=eth0 OUT= MAC=aa:bb:cc SRC=yy.yy.yy.yy DST=xx.xx.xx.xx LEN=48 TOS=0x00 PREC=0x00 TTL=54 ID=55025 DF PROTO=TCP SPT=63776 DPT=1999 WINDOW=65535 RES=0x00 SYN URGP=0 Sep 24 14:06:25 myserver kernel: [xx.xx] iptables: IN=eth0 OUT= MAC=aa:bb:cc SRC=yy.yy.yy.yy DST=xx.xx.xx.xx LEN=48 TOS=0x00 PREC=0x00 TTL=54 ID=54521 DF PROTO=TCP SPT=63776 DPT=1999 WINDOW=65535 RES=0x00 SYN URGP=0 Sep 24 14:06:55 myserver kernel: [xx.xx] iptables: IN=eth0 OUT= MAC=aa:bb:cc SRC=yy.yy.yy.yy DST=xx.xx.xx.xx LEN=100 TOS=0x00 PREC=0x00 TTL=54 ID=35050 PROTO=TCP SPT=63088 DPT=22 WINDOW=33304 RES=0x00 ACK PSH URGP=0 Sep 24 14:06:55 myserver kernel: [xx.xx] iptables: IN=eth0 OUT= MAC=aa:bb:cc SRC=yy.yy.yy.yy DST=xx.xx.xx.xx LEN=52 TOS=0x00 PREC=0x00 TTL=54 ID=14076 PROTO=TCP SPT=63088 DPT=22 WINDOW=33264 RES=0x00 ACK URGP=0 Sep 24 14:06:55 myserver kernel: [xx.xx] iptables: IN=eth0 OUT= MAC=aa:bb:cc SRC=yy.yy.yy.yy DST=xx.xx.xx.xx LEN=52 TOS=0x00 PREC=0x00 TTL=54 ID=5277 PROTO=TCP SPT=63088 DPT=22 WINDOW=33248 RES=0x00 ACK URGP=0 Sep 24 14:06:56 myserver kernel: [xx.xx] iptables: IN=eth0 OUT= MAC=aa:bb:cc SRC=yy.yy.yy.yy DST=xx.xx.xx.xx LEN=100 TOS=0x00 PREC=0x00 TTL=54 ID=25501 PROTO=TCP SPT=63088 DPT=22 WINDOW=33304 RES=0x00 ACK PSH URGP=0 As you can see, I typed xx.xx.xx.xx:1999 in my browser, and it tried to connect until it timed out. 1) There are many similar lines for just one event. Do you think I need all of them? How would I avoid duplicates? 2) The last 4 lines are for my port 22. But since I allow port 22 INPUT for my web server, why are they here? 3) Do I need info like LEN,TOS,PREC and others? I'm trying to find a page that explains them one by one, by I can't find anything.

    Read the article

  • Add user in CentOS 5

    - by Ron
    I created a new user in my CentOS web server with useradd. Added a password with passwd. But I can't log in with the user via SSH. I keep getting 'access denied'. I checked to make sure that the password was assigned and that the account is active. /var/log/secure shows the following error: Aug 13 03:41:40 server1 su: pam_unix(su:auth): authentication failure; logname= uid=500 euid=0 tty=pts/0 ruser=rwade rhost= user=root Please help, Thanks Thanks for the responses so far: I should add that it is a VPS on a remote computer, fresh out of the box. I can log in as the root user quite fine. I can also su to the new user, but I cannot log in as the new user. Here is my sshd_config file: # $OpenBSD: sshd_config,v 1.73 2005/12/06 22:38:28 reyk Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/usr/local/bin:/bin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. #Port 22 #Protocol 2,1 Protocol 2 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # HostKey for protocol version 1 #HostKey /etc/ssh/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh/ssh_host_rsa_key #HostKey /etc/ssh/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 768 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH SyslogFacility AUTHPRIV #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes #StrictModes yes #MaxAuthTries 6 #RSAAuthentication yes #PubkeyAuthentication yes #AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no PasswordAuthentication yes # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes ChallengeResponseAuthentication no # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no GSSAPIAuthentication yes #GSSAPICleanupCredentials yes GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication mechanism. # Depending on your PAM configuration, this may bypass the setting of # PasswordAuthentication, PermitEmptyPasswords, and # "PermitRootLogin without-password". If you just want the PAM account and # session checks to run without PAM authentication, then enable this but set # ChallengeResponseAuthentication=no #UsePAM no UsePAM yes # Accept locale-related environment variables AcceptEnv LANG LC_CTYPE LC_NUMERIC LC_TIME LC_COLLATE LC_MONETARY LC_MESSAGES AcceptEnv LC_PAPER LC_NAME LC_ADDRESS LC_TELEPHONE LC_MEASUREMENT AcceptEnv LC_IDENTIFICATION LC_ALL #AllowTcpForwarding yes #GatewayPorts no #X11Forwarding no X11Forwarding yes #X11DisplayOffset 10 #X11UseLocalhost yes #PrintMotd yes #PrintLastLog yes #TCPKeepAlive yes #UseLogin no #UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #ShowPatchLevel no #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner /some/path # override default of no subsystems Subsystem sftp /usr/libexec/openssh/sftp-server

    Read the article

  • tmpreaper, --protect and a non-root user

    - by nsg
    Hi, I'm a little confused. I have a download directory that I want to remove all files older then 30 days with tmpreaper. Just one problem, the directory in question is a separate partition with a lost+found directory, of course I need to keep it so I added --protect 'lost+found', the problem is that tmpreaper outputs: error: chdir() to directory 'lost+found' (inode 11) failed: Permission denied (PID 30604) Back from recursing down `lost+found'. Entry matching `--protect' pattern skipped. `lost+found' I have tried with other pattern like lost* and so on... I'm running tmpreaper as a non-root user because there is no reason for superuser privileges because I own all files (except lost+found). Are I'm forced to run tmpreaper as root? Or are my shell-skills not as good as I thought? I guess the problem is: tmpreaper will chdir(2) into each of the directories you've specified for cleanup, and check for files matching the <shell_pattern> there. It then builds a list of them, and uses that to protect them from removal. Any thought and/or advice? Edit: The command I'm trying to run is something like $ /usr/sbin/tmpreaper -t --protect 'lost+found' 30d /mydir 1> /dev/null error: chdir() to directory `lost+found' (inode 11) failed: Permission denied Edit 2: I read the source code for tmpreaper-1.6.13 and found this if (safe_chdir (dirname)) exit(1); and if (chdir (dirname)) { message (LOG_ERROR, "chdir() to directory `%s' (inode %lu) failed: %s\n", dirname, (u_long) sb1.st_ino, strerror (errno)); return 1; } So it seems tmpreaper needs to be able to chdir in to all directories, ignored or not. I see two options left Run tmpreaper as root Move the download directory Find a alternative tool (tmpwatch?) I will give it some more research before i make a choice.

    Read the article

  • Make `mount` choose a device

    - by o_O Tync
    I have a mount point — let it be /media/question — and two possible devices: a physical HDD and a remote NFS folder. Sometimes I plug the device in physically, in other cases I mount it via NFS. Is there a way to specify both of them in fstab so that executing mount /media/question will preferably choose physical volume, and when it's not available — NFS?

    Read the article

  • Impossible to stop raid device

    - by Traroth
    I'm trying to stop a RAID disk in order to replace it by a new one, as this one is not working properly. I'm typing mdadm --stop /dev/md1, and I'm getting an error message: mdadm: fail to stop array /dev/md1: Device or resource busy I'm getting this message even if I reboot the server, and I can't see a process that could cause this. The server is working under a Debian with a 2.6.18-4-amd64 kernel. Could you help? Edit: Mote details about what my colleague tried out. After unmounting sda1, the command mdadm --remove /dev/md0 /dev/sda1 worked. But now, we still have an error message after mdadm --remove /dev/md1 /dev/sda5: mdadm: hot remove failed for /dev/sda5: Device or resource busy I still don't understand completly how the different partitions are mounted, so I suppose there is something I don't understand in the currenct situation...

    Read the article

  • Taking a screencast in Backtrack 4

    - by user30196
    I'm working on a tutorial using Backtrack 4 Live USB, and I would like to take a screencast of what I'm doing (not just screenshots) So far I have tried these application with limited success: -recordmydesktop -xvidcap -wink -istanbul -vlc -vnc2flv Each time I try the resulting files are generally choppy (at best 1 frame per second) and most don't even end up with a clear view of the screen each time. If anyone has suggestions for the screencast I would greatly appreciate it.

    Read the article

  • Lubuntu LiveCD disabling auto-mount.

    - by PxE Booter
    In cooperation with my IT teacher we want to boot all PC's in IT class with Lubuntu. I've successfully set up PXE server, but there is one thing that worries us. Harddrives shouldn't be accessible from booted Lubuntu(normal user only). Would adding to fstab something like: /dev/sda1 /Idk/What auto noauto work? I'd like to add that I can uncompress squashfs livecd filesystem. If no, what other solution is there, to block auto-mounting /dev/sda drive?

    Read the article

  • Debian Testing installs Iceweasel ESR (severely outdated)?

    - by Lucas Phillips
    I just reinstalled Debian Testing, and for some reason, instead of Iceweasel 25, I have 17. The installed and candidate versions are both 17.0.9esr-1~deb7u1. apt-get update && apt-get upgrade does nothing, and it seems that version 17 is the latest for this install. I was on Debian Testing before, and Iceweasel was at the latest version. Even Debian Stable had an Iceweasel version 20. Why would it be trying to install ESR now?

    Read the article

  • How do ALSA and PulseAudio relate?

    - by Hanno Fietz
    While trying to get my sound to work, I was wondering about the roles of ALSA and PulseAudio. I have both installed and was wondering, for example, which of them needs to know about my sound card. Both seem to be able to use each other, there's a pulseaudio plugin for ALSA, and on my system, alsa shows up as a sound card in pulseaudio. Which of the two does what, are they alternatives or complementary?

    Read the article

  • Webcam error (libv4lconvert) while capturing VIDEO

    - by shadyabhi
    I get the following when I capture images using my web-cam.. libv4lconvert: Error decompressing JPEG: unknown huffman code: 0000ffff libv4lconvert: Error decompressing JPEG: unknown huffman code: 0000ffff libv4lconvert: Error decompressing JPEG: unknown huffman code: 0000ffff ...(same error repeating) ... I also had issue that my camera was not getting detected in ubuntu. So, in order to run an application that uses the webcam, I have to run a command like LD_PRELOAD=/usr/lib/libv4l/v4l1compat.so ./6dofhand Whats causing these errors?

    Read the article

  • Second network card configuration not working.

    - by Sebas
    I have 4 servers running Centos 5. All of them have two ethernet network cards. I have configured 192.168.1.x IP addresses on their eth0 card. They are all connected to the same switch using their eth0 card and they are all working. I have configured 10.72.11.x IP addresses on their eth1 card.They are all connected to the same switch - a different one from the switch used with eth0 card - using their eth1 card and they are NOT all working. Their configuration files is like: DEVICE=eth1 BOOTPROTO=static IPADDR=10.72.11.236 BROADCAST=10.72.11.191 NETMASK=255.255.255.192 NETWORK=10.72.11.128 HWADDR=84:2B:2B:55:4B:98 IPV6INIT=yes IPV6_AUTOCONF=yes ONBOOT=yes The interfase is starting and configured as I need. [root@sql1 network-scripts]# ifconfig eth0 Link encap:Ethernet HWaddr 84:2B:2B:55:4B:97 inet addr:192.168.1.105 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::862b:2bff:fe55:4b97/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2981 errors:0 dropped:0 overruns:0 frame:0 TX packets:319 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:386809 (377.7 KiB) TX bytes:66134 (64.5 KiB) Interrupt:36 Memory:da000000-da012800 eth1 Link encap:Ethernet HWaddr 84:2B:2B:55:4B:98 inet addr:10.72.11.236 Bcast:10.72.11.191 Mask:255.255.255.192 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:48 Memory:dc000000-dc012800 I also added a route-eth1 file that looks like: 10.0.0.0/8 via 10.72.11.254 Routing looks fine to me: [root@sql1 network-scripts]# netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.72.11.192 0.0.0.0 255.255.255.192 U 0 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 10.0.0.0 10.72.11.254 255.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 But I cannot ping one server from the other. [root@sql1 network-scripts]# ping 10.72.11.235 PING 10.72.11.235 (10.72.11.235) 56(84) bytes of data. From 10.72.11.236 icmp_seq=1 Destination Host Unreachable From 10.72.11.236 icmp_seq=2 Destination Host Unreachable From 10.72.11.236 icmp_seq=3 Destination Host Unreachable From 10.72.11.236 icmp_seq=4 Destination Host Unreachable From 10.72.11.236 icmp_seq=5 Destination Host Unreachable From 10.72.11.236 icmp_seq=6 Destination Host Unreachable ^C --- 10.72.11.235 ping statistics --- 7 packets transmitted, 0 received, +6 errors, 100% packet loss, time 6033ms , pipe 3 What am I doing wrong?

    Read the article

  • How can I remove OLD history from Google Chrome?

    - by Norman Ramsey
    I'm working on a laptop with a modest hard drive, and 500MB is taken up with Google Chrome "History Index" and "Thumbnails" files. Some of these files are a year old. Chrome offers me the option to remove recent history, but I want the opposite: I want to remove old history. (Ideally I would remove the least recently used history information, but I don't expect to be able to do that.) Anyone have any ideas? I'm running the standard Debian google-chrome-beta package.

    Read the article

  • How do you persist installed software & configurations on an Amazon EC2 instance?

    - by Richard
    I've gotten a base Debian AMI up and running and now I need to know the best way to maintain it. I've ran the updates (aptitude update/upgrade) and installed/configured my software (Apache, Ruby, etc.) but if I reboot the instance or start a new one I'll have to do all this work over again. How do you persist these types of things over a reboot? Do you build a new AMI every time you adjust some tiny piece of the system? Or is there some way to feed it a script on startup that configures it in "real-time"? I know I could go all the way with a Reductive Labs Puppet style setup but that's a bit too much for my needs right now (1-2 servers). Any best practices on this? Update: I found a bit of information on using User-Data to run scripts at instance boot time.

    Read the article

  • mount fstab partition with public access

    - by Mikhail
    How do I specify that an fstab mount-point should be public? I want /mnt/windows to be accessible to normal users. I believe I am using ntfs-3g. If I set the /mnt/windows to 777 will it be publicly accessible without changing the permissions on the NTFS disk? /dev/sdb4 /mnt/windows ntfs noatime 0 1 /dev/sdb5 / ext4 noatime 0 1 UUID=5AA4-168D /boot/efi vfat defaults 0 1 and localhost my_computer # stat /mnt/windows/ File: '/mnt/windows/' Size: 12288 Blocks: 24 IO Block: 512 directory Device: 814h/2068d Inode: 5 Links: 1 Access: (0700/drwx------) Uid: ( 0/ root) Gid: ( 0/ root) Access: 2014-08-21 18:29:13.597722200 -0500 Modify: 2014-08-21 18:29:13.597722200 -0500 Change: 2014-08-21 18:29:13.597722200 -0500 Birth: -

    Read the article

  • killing all instances of chrome on the command line?

    - by Fedor
    In some cases killing a single tab/process doesn't do it and I need to close Chrome entirely. Since Chrome has multiple processes, how can I close all of them at once? I know that... pgrep chrome returns all the pids, can someone tell me a trick that would allow me to close all of them by feeding them to another command or merging them to a csv or something?

    Read the article

  • Move Ubuntu to another drive

    - by Ben Dilts
    I have a laptop with an 80GB SSD and 500GB HDD. I currently have Windows installed on the SSD, and a 400GB data partition for Windows on the HDD. I set aside 100GB on the HDD to try out Ubuntu, and I'd like to make it my primary OS and switch it over to the (much) faster SSD. How could I go about getting my Ubuntu setup moved over to the SSD? I have a 120GB USB hard drive I can use if necessary for getting through it.

    Read the article

< Previous Page | 386 387 388 389 390 391 392 393 394 395 396 397  | Next Page >