Search Results

Search found 24933 results on 998 pages for 'arch linux'.

Page 396/998 | < Previous Page | 392 393 394 395 396 397 398 399 400 401 402 403  | Next Page >

  • Only tunnel certain applications via OpenVPN

    - by jinjin
    Hi, I've purchased a VPN solution, it works correctly when I have "redirect-gateway def1" in the configuration file (routing all traffic through the VPN). However when I remove that line from the configuration file, I am still able to ping-out of the machine (ping -I tap0), however I cannot ping the IP assigned to the machine (it's a public ip), i get the error: Destination Host Unreachable. I only want to have certain applications sending traffic through the VPN tunnel (eg: ZNC, irssi), all of which i can select which IP they use. However they can't recieve any data, making the tunnel essentially useless to me when disabling redirect-gateway. Any ideas on how to allow specific applications use the tunnel, without of forcing everything to go through it? My configuration file is as follows: dev tap remote #.#.#.# float #.#.#.# port 5129 comp-lzo ifconfig #.#.#.# 255.255.255.128 route-gateway #.#.#.# #redirect-gateway def1 secret key.txt cipher AES-128-CBC The output of ifconfig -a when the tunnel is connected: tap0 Link encap:Ethernet HWaddr 00:ff:47:d3:6d:f3 inet addr:#.#.#.# Bcast:#.#.#.# Mask:255.255.255.255 inet6 addr: <snip> Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:612 errors:0 dropped:0 overruns:0 frame:0 TX packets:35 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:25704 (25.1 KiB) TX bytes:6427 (6.2 KiB) EDIT: the Bcast:#.#.#.# (ifconfig) is different from route-gateway #.#.#.# (openvpn) if that makes any difference.

    Read the article

  • Tool to bulk speed up/convert an audio file

    - by User1
    I want to listen to certain podcasts on my phone but I have two common problems: The audio is in some weird format (some don't play on my phone). The audio is slow. I want to use something like sox or avconv to bulk convert the files. Since this is just voice and going on a cell phone, small low-quality files would be best for me. I had some good success using avconv: avconv -i weird.wma normal.ogg Unforunately, this command creates an enormous ogg file and I can't get it play faster. Ideally, this particular file would play at 170% of the original speed.

    Read the article

  • Cannot boot from Yumi multiboot USB stick

    - by Amator
    I've just created a multiboot USB stick using Yumi. I tried to start my notebook (Asus K70IO) using it, but all I see is just a black screen with blinking underscore even after waiting for minutes. If during this time I remove the USB stick I get the message: "Operating system load error". How do I properly load my Yumi USB stick and use it? I've tried formatting it using Yumi's checkbox to format the stick in FAT32 too, but it didn't help. Now I tried to use Sardu 2.0.5 and met same problem: black screen and blinkin underscore, if I remove stick I see "Operating system load error" and my OS starts to boot. At the same time if I create bootable USB stick from ISO using UltraISO it boots smoothly.

    Read the article

  • What is the most secure way to allow a user read access to a log file?

    - by gAMBOOKa
    My application requires read access to /var/log/messages, which belongs to user and group root. What is the minimal exposure level required on /var/log/messages so my application can read it? Presently, my plan is to change the group ownership of /var/log/messages to a new group, and add root and my application user to it, but this would also give the application write privileges to /var/log/messages. OS: Centos 5.5

    Read the article

  • script to su with password in script without root

    - by Triplell89
    I have scripted a process that involves updating symbolic links on files located on 3 different machines. On those machines exists 4 users each, who each need to have these links updated. Using su, is there a way to pass the password argument to the command on a single line, without invoking sudo as the users will not have admin rights? My only alternative solution at this point is to ssh around, however I would like to be able to do this without hardcoding in a bunch of hosts/ips.

    Read the article

  • dovecot rhel 5 installation fails because of newer libraries

    - by kayhan yüksel
    to whom it may respond to, we are trying to install dovecot (dovecot-2.2.10-1_14.el5.x86_64) on a RHEL 5.4 server and we get the error : [root@asgfkm /]# rpm -i dovecot-2.1.17-0_136.el5.x86_64.rpm uyarý: dovecot-2.1.17-0_136.el5.x86_64.rpm: Header V4 DSA/SHA1 Signature, key ID 66534c2b: NOKEY hata: Failed dependencies: libcrypto.so.6()(64bit) is needed by dovecot-1:2.1.17-0_136.el5.x86_64 libldap-2.3.so.0()(64bit) is needed by dovecot-1:2.1.17-0_136.el5.x86_64 libmysqlclient.so.15()(64bit) is needed by dovecot-1:2.1.17-0_136.el5.x86_64 libmysqlclient.so.15(libmysqlclient_15)(64bit) is needed by dovecot-1:2.1.17-0_136.el5.x86_64 libssl.so.6()(64bit) is needed by dovecot-1:2.1.17-0_136.el5.x86_64 [root@asgfkm /]# but when we try to install requested libraries, it conflicts with the never libraries : uyarý: openssl-0.9.8e-27.el5_10.1.x86_64.rpm: Header V3 DSA/SHA1 Signature, key ID e8562897: NOKEY openssl-1.0.0-20.el6.x86_64 paketi zaten yüklü (openssl-0.9.8e-27.el5_10.1.x86_64 sürümünden daha yeni) this is happening with the other libraries also : libldap, libmysql, etc... Do you recommend --force option to install it or is there any other proper way around ? Thank you for your time,

    Read the article

  • Route return traffic to correct gateway depending on service

    - by Marnix van Valen
    On my office network I have two internet connections and one CentOS server running a website (HTTPS on port 443). The website should be publicly accessible through the public IP of the first internet connection (ISP-1). The other internet connection, ISP-2, id the default gateway on the network. Both internet connections have routers (the household-kind) with NAT, SPI firewalls etc. The router on ISP-2 is a Netgear WNDR3700 (aka N600) with original firmware. The problem is that the website is unreachable. Looks like incoming traffic on ISP-1 will reach the server but the returning traffic is routed through ISP-2, effectively making the site unreachable. As far as I can tell I can't do port based routing on the WNDR3700. What are my options to make this work? I've been looking at implementing an iptables / routing based solution on the server itself but haven't been able to make that work. Update: Note that the server has one network interface connecting it to both routers.

    Read the article

  • Debian: SSH: "PermitRootLogin=forced-commands-only" stopped working

    - by Brent
    I have several servers running Debian Lenny. Just recently I discovered the PermitRootLogin=forced-commands-only directive for ssh, which allows me to run a scripted rsync as root with an ssl key, without enabling more generalized root ssh access. However, last week this stopped working - it appears on all of my servers - and I can't figure out why. Everything continues to work fine with PermitRootLogin=yes, but I would prefer to block root logins - especially via passwords. The day it stopped working, we reconfigured some of the ports on one of our switches (which we later reverted), but I can't see that affecting this, since it still works with PermitRootLogin set to yes. How can I diagnose why the forced-commands-only directive has apparently stopped working?

    Read the article

  • Routing table with two NIC adapters in libvirt/KVM

    - by lzap
    I created a virtual NAT network (192.168.100.0/24 network) in my libvirt and new guest with two interfaces - one in this network, one as bridged (10.34.1.0/24 network) to the local LAN. The reason for that is I need to have my own virtual network for my DHCP/TFTP/DNS testing and still want to access my guest externally from my LAN. On both networks I have working DHCP, both giving them IP addresses. When I setup NAT port forwarding (e.g. for ssh), I can connect to the eth0 (virtual network), everything is fine. But when I try to access the eth1 via bridged interface, I have no response. I guess I have problem with my routing table - outgoing packets are routed to the virtual NAT network (which has access to the machine I am connecting from - I can ping it). But I am not sure if this setup is correct. I think I need to add something to my routing table. # ifconfig eth0 Link encap:Ethernet HWaddr 52:54:00:B4:A7:5F inet addr:192.168.100.14 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:feb4:a75f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16468 errors:0 dropped:27 overruns:0 frame:0 TX packets:6081 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:22066140 (21.0 MiB) TX bytes:483249 (471.9 KiB) Interrupt:11 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 52:54:00:DE:16:21 inet addr:10.34.1.111 Bcast:10.34.1.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:fede:1621/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:189 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4911 (4.7 KiB) TX bytes:9 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.34.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 1002 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1003 0 0 eth1 0.0.0.0 192.168.100.1 0.0.0.0 UG 0 0 0 eth0 Network I am trying to connect from is different than network the hypervisor is connected to: 10.36.0.0. But it is accessible from that network. So I tried to add new route rule: route add -net 10.36.0.0 netmask 255.255.0.0 dev eth1 And it is not working. I thought setting correct interface would be sufficient. What is needed to get my packets coming through?

    Read the article

  • How do I limit concurrent sftp / port forwarding logins

    - by Kyoku
    I have ssh set up so my users can only access sftp and port forwarding, how can I limit the number of concurrent logins on a per user basis? In my sshd_config I have UsePAM set to yes and in /etc/security/limits.conf I have: username - maxlogins 1 I also tried: username hard maxlogins 1 Neither of these works and the users can still log in multiple times.

    Read the article

  • crontab: question about a special case of the dash character in the time field spec

    - by mdpc
    In the SuSE /etc/crontab the entry to run the cron.{hourly,daily,monthly,weekly} scripts is coded as: -*/15 * * * * root test -x /usr/lib/cron/run-crons && /usr/lib/cron/run-crons /dev/null 2&1 Notice that the very first character of the specification is a dash character (-), and this is NOT a typo. Can somebody explain what the time spec '-*/15' means? BTW, the stuff seems to be running fine. Thanks

    Read the article

  • Mass editing videos on Ubuntu?

    - by rick
    Hi, I'm trying to add a watermark and a credits image to all of my old videos. I downloaded them off YouTube so they are all flv (H.264?). Is there some software that will allow me do simple edits in batches? I know a little bit of Python and tried looking at some of the library but they all seem like overkill (and way above my head). So is there a solution besides getting some software and going through all my videos and doing it manually? They are all mostly the same length, but it would be nice to specify a relative position for my credits. e.g. show a static image for 10 seconds when the video is at 95%

    Read the article

  • SSH stops at "using username" with IPTables in effect

    - by Rautamiekka
    We used UFW but couldn't make the Source Dedicated ports open, which was weird, so we purged UFW and switched to IPTables, using Webmin to configure. If the inbound chain is on DENY and SSH port open [judged from Webmin], PuTTY will say using username "root" and stops at that instead of asking for public key pw. Inbound chain on ACCEPT the pw is asked. This problem didn't happen with UFW. Picture of IPTables configuration in Webmin: http://s284544448.onlinehome.us/public/PlusLINE%20Dedicated%20Server,%20Webmin,%20IPTables,%200.jpgThe address is to the previous rautamiekka.org. iptables-save when on INPUT DENY: # Generated by iptables-save v1.4.8 on Wed Apr 11 16:09:20 2012 *mangle :PREROUTING ACCEPT [1430:156843] :INPUT ACCEPT [1430:156843] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [1415:781598] :POSTROUTING ACCEPT [1415:781598] COMMIT # Completed on Wed Apr 11 16:09:20 2012 # Generated by iptables-save v1.4.8 on Wed Apr 11 16:09:20 2012 *nat :PREROUTING ACCEPT [2:104] :POSTROUTING ACCEPT [0:0] :OUTPUT ACCEPT [0:0] COMMIT # Completed on Wed Apr 11 16:09:20 2012 # Generated by iptables-save v1.4.8 on Wed Apr 11 16:09:20 2012 *filter :INPUT DROP [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [1247:708906] -A INPUT -i lo -m comment --comment "Machine-within traffic - always allowed" -j ACCEPT -A INPUT -p tcp -m comment --comment "Services - TCP" -m tcp -m multiport --dports 22,80,443,10000,20,21 -m state --state NEW,ESTABLISHED -j ACCEPT -A INPUT -p tcp -m comment --comment "Minecraft - TCP" -m tcp --dport 25565 -j ACCEPT -A INPUT -p udp -m comment --comment "Minecraft - UDP" -m udp --dport 25565 -j ACCEPT -A INPUT -p tcp -m comment --comment "Source Dedicated - TCP" -m tcp --dport 27015 -j ACCEPT -A INPUT -p udp -m comment --comment "Source Dedicated - UDP" -m udp -m multiport --dports 4380,27000:27030 -j ACCEPT -A INPUT -p udp -m comment --comment "TS3 - UDP - main port" -m udp --dport 9987 -j ACCEPT -A INPUT -p tcp -m comment --comment "TS3 - TCP - ServerQuery" -m tcp --dport 10011 -j ACCEPT -A OUTPUT -o lo -m comment --comment "Machine-within traffic - always allowed" -j ACCEPT COMMIT # Completed on Wed Apr 11 16:09:20 2012 iptables --list when on INPUT DENY: Chain INPUT (policy DROP) target prot opt source destination ACCEPT all -- anywhere anywhere /* Machine-within traffic - always allowed */ ACCEPT tcp -- anywhere anywhere /* Services - TCP */ tcp multiport dports ssh,www,https,webmin,ftp-data,ftp state NEW,ESTABLISHED ACCEPT tcp -- anywhere anywhere /* Minecraft - TCP */ tcp dpt:25565 ACCEPT udp -- anywhere anywhere /* Minecraft - UDP */ udp dpt:25565 ACCEPT tcp -- anywhere anywhere /* Source Dedicated - TCP */ tcp dpt:27015 ACCEPT udp -- anywhere anywhere /* Source Dedicated - UDP */ udp multiport dports 4380,27000:27030 ACCEPT udp -- anywhere anywhere /* TS3 - UDP - main port */ udp dpt:9987 ACCEPT tcp -- anywhere anywhere /* TS3 - TCP - ServerQuery */ tcp dpt:10011 Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere /* Machine-within traffic - always allowed */ The UFW rules prior to purging on INPUT DENY: 127.0.0.1 ALLOW IN 127.0.0.1 3306 DENY IN Anywhere 20,21/tcp ALLOW IN Anywhere 22/tcp (OpenSSH) ALLOW IN Anywhere 80/tcp ALLOW IN Anywhere 443/tcp ALLOW IN Anywhere 989 ALLOW IN Anywhere 990 ALLOW IN Anywhere 8075/tcp ALLOW IN Anywhere 9987/udp ALLOW IN Anywhere 10000/tcp ALLOW IN Anywhere 10011/tcp ALLOW IN Anywhere 25565/tcp ALLOW IN Anywhere 27000:27030/tcp ALLOW IN Anywhere 4380/udp ALLOW IN Anywhere 27014:27050/tcp ALLOW IN Anywhere 30033/tcp ALLOW IN Anywhere

    Read the article

  • Where does netstat get the process name?

    - by tjameson
    I am developing a node application and there is an option to set the process title (process name). This only sets it in some tools (like ps and top), but not in htop or netstat. I found this article that explained how most applications do it, but it doesn't change in netstat. That lead me to wonder where those programs are getting the process name. Would they be getting it from /proc/##/cmdline? (## being the PID of the process) I figure messing with things in /proc is a bad idea (and probably not possible), so if this is where those programs are getting it, is there a way to change it?

    Read the article

  • Iptables NAT logging

    - by Gerard
    I have a box setup as a router using Iptables (masquerade), logging all network traffic. The problem: Connections from LAN IPs to WAN show fine, i.e. SRC=192.168.32.10 - DST=60.242.67.190 but for traffic coming from WAN to LAN it will show the WAN IP as the source, but the routers IP as the destination, then the router - LAN IP. I.e. SRC=60.242.67.190 - DST=192.168.32.199 SRC=192.168.32.199(router) - DST=192.168.32.10 How do I configure it so that it logs the conversations correctly? SRC=192.168.32.10 - DST=60.242.67.190 SRC=60.242.67.190 DST=192.168.32.10 Any help appreciated, cheers

    Read the article

  • 2 Printers 1 Queue

    - by Shazburg
    My issue: When an order is processed, the same document needs to be printed on two printers. My proposed solution: Create a single queue in CUPS with a backend script that spits the job out to the two real printers queues. My problem: Documentation. Maybe I'm looking at every ring around the bullseye, but I can't find anything that lays out the rules for writing a CUPS backend script. In the end, I have several questions: Is there already an option to do this in CUPS that I've missed? The line I use to add my queue is "lpadmin -p MultiPass -E -v multipass -P Generic PostScript Printer". But DeviceURI is bad unless I specify a directory like "-v multipass:/tmp". Why is this? For testing, my script does nothing but capture ARGV and write it out to a text file one line per argument. Problem is, I'm getting nothing. Logs show the job as successful, but I'm pretty sure my meager attempt at a backend isn't even being run. I've tried to keep this question brief, so please ask for more info as I'm sure I've left out the most important part in all this. Honestly, I'm just done chasing my own tail. Thank you for your time.

    Read the article

  • Problems connecting Centos on VMware to the network using bridged connection.

    - by Sakin
    Hi, I installed CentOs on VMware running on windows XP. When trying to configure it to connect to the internet in a bridged configuration, I get an error message when trying to bring up the network interface: [root@VMLinux ~]# /et/init.d/network start Bringing up loopback interface: [ OK ] Bringing up interface eth0: Determining IP information for eth0... failed [FAILED] VM is running on a machine that has access to the network, I tried it on two different networks that have DHCP enabled. Everything works fine when using a NAT connection through my host. How can I make the bridge work for me? Thanks.

    Read the article

  • Does a successful exit of rsync -acvvv s d guarantee identical directory trees?

    - by user259774
    I have two volumes, one xfs, and another ntfs - ntfs was empty, and xfs had 10 subitems. I needed to sync them. I initially copied a few of the subitems by dragging them over in a gui fm. Several of the direct descendants which i had dragged finished, apparently. One I stopped before it was done, and the rest I cancelled while it still appeared to be gathering information about the files. Then I ran rsync -acvvv xmp/ nmp/, where xmp and nmp are the volumes' respective mountpoints, which exited with a 0 status. find xmp -printf x | wc -c and find nmp -printf x | wc -c both return 372926. My question is: Am I guaranteed that the two drives' contents are identical?

    Read the article

  • VLC RTP Streaming in FC12

    - by Matt D
    I'm trying to get VLC to work streaming RTP audio/video over my office network. The goal is multicast a/v streaming. In all test cases, we are streaming from VLC to VLC. I am able to stream from Windows to Windows, and from Fedora to Windows, but not from Windows to Fedora. Additionally, I am unable to receive a LOCAL stream from one instance of VLC to another, within Fedora. I don't see any reason why this would be. The buffer indicator (where the elapsed/total time is normally displayed) never shows any connectivity, so it would appear to be a network problem, but since I am able to stream from Fedora to Windows (same IP, same port) I thought it would be something else. Does anyone know of a solution to this issue?

    Read the article

  • HELP! Free space not reclaimed after online resizing ext4 in Ubuntu 9.10

    - by TiansHUo
    My root partition was filling up, with only 500 mbs left, I wanted to resize my root partition from 20 Gb to 40Gb So I resized my partition by using these steps: Using Gparted to resize another partition to give space for the EXT4 Using fdisk, deleting the root partition (on /dev/sda2), and creating it again using the new size resize2fs /dev/sda2 Updating grub2 But now the problem is that although I can boot in my new partition and the new partition shows it is 40Gb, but the free size was still 500mb. So I booted from a LiveCD and checked with e2fsck -p /dev/sda2, it reported clean. So I added the -f flag (force check), still, the drive is full.

    Read the article

  • What's going on with traceroute?

    - by Kevin
    The following is what happens when I run traceroute from a certain location: # traceroute google.com traceroute to google.com (74.125.227.39), 30 hops max, 60 byte packets 1 gateway.local.enactpc.com (10.0.0.1) 0.138 ms 0.101 ms 0.084 ms 2 * * * 3 * * * 4 * * * 5 * * * 6 * * * 7 * * * 8 * * * 9 * * * 10 * * * 11 * * * 12 * * * 13 * * * 14 * * * 15 * * * 16 * * * 17 * * * 18 * * * 19 * * * 20 * * * 21 * * * 22 * * * 23 * * * 24 * * * 25 * * * 26 * * * 27 * * * 28 * * * 29 * * * 30 * * * Absolutely nothing of interest... Now, originally I thought this was just a fact of the location's network set up. (I assume they block pings or something...) However, watch what happens when I use nmap to run a traceroute... # nmap -sP --traceroute google.com Starting Nmap 5.21 ( http://nmap.org ) at 2012-09-25 22:18 CDT Nmap scan report for google.com (74.125.227.40) Host is up (0.034s latency). Hostname google.com resolves to 11 IPs. Only scanned 74.125.227.40 rDNS record for 74.125.227.40: dfw06s06-in-f8.1e100.net TRACEROUTE (using proto 1/icmp) HOP RTT ADDRESS 1 0.19 ms gateway.local.enactpc.com (10.0.0.1) 2 1.93 ms 99-20-92-1.lightspeed.austtx.sbcglobal.net (99.20.92.1) 3 25.61 ms 99-20-92-2.lightspeed.austtx.sbcglobal.net (99.20.92.2) 4 ... 6 7 23.68 ms 12.83.68.137 8 31.30 ms gar23.dlstx.ip.att.net (12.122.85.73) 9 ... 10 31.82 ms 72.14.233.65 11 32.27 ms 209.85.250.77 12 32.98 ms dfw06s06-in-f8.1e100.net (74.125.227.40) Nmap done: 1 IP address (1 host up) scanned in 3.29 seconds When using nmap I get A LOT more results than with traceroute, why? Note, I checked, and the difference in target IP addresses is not related...

    Read the article

  • How Do I Use Multiple Versions of OpenSSL ... One for Apache and one for PHP

    - by Ken S.
    I have an Apache 2.2 (self-compiled version) server that is getting dinged during a PCI scan because it does not support TLS 1.1 or 1.2 ciphers. After some digging I found that the installed version of OpenSSL (0.9.8e) does not contain the newest TLS ciphers. So I went and downloaded and compiled the latest version of OpenSSL (1.0.1c) and have it installed in an alternate location within /opt so it wouldn't interfere with the installed version. What I would like to do is to compile Apache against the 1.0.1 libraries and keep the system-installed libraries for use with PHP, cURL, openssh, etc. I'm hoping that doing it this way will allow Apache to use the newest TLS but not break anything with any other programs that require the old libraries. I thought I could do this by adding an entry in to /etc/ld.so.conf that pointed to the new libraries, but I think this will conflict with the existing ones. i.e. two references to libcrypto could cause everything to have issues. The main reason for doing this is because of issues with PHP cURLing to external servers and having issues with the latest OpenSSL libs thus requiring edits to our PHP code. Would love some guidance on how best to accomplish this.

    Read the article

< Previous Page | 392 393 394 395 396 397 398 399 400 401 402 403  | Next Page >