Search Results

Search found 21717 results on 869 pages for 'setup versions'.

Page 478/869 | < Previous Page | 474 475 476 477 478 479 480 481 482 483 484 485  | Next Page >

• Flexible virtualization infrastructure Design with libvirt

  - by Lessfoe

  I'm going to install a CentOS6 Server with Virtualization ( libvirtd ) capabilities on a DELL Server with Hardware RAID5 of around 6T of disk space ( It has 4x2T disks in a PERC700 RAID Controller ). I'm going then to install some guests which requires few resources except one that needs 500GB of disk space, 8/16GB of RAM and good performances. I was thinking about file images for guests storage but I'm not sure about the 500GB VM what needs good performances so that an LVM device could be better. So my question is what would be the best layout concerning: RAID setup ( RAID5, RAID1 + 1 disk for OS only. ) disk partitioning ( using the entire disk/ leave free space for future use and extending it with LVM ) guests storage management ( LVM devices or file images ( considering the 500GB VM that is performance demanding ) or mixed ) Where to put guests storage? /var/lib/libvirt/images or maybe in a custom dir separated from system /home/VMs Thanks in advance for any hint.

  Read the article

• How do I configure networking when using XEN on 12.04 Server

  - by Ingram

  I'm following this guide, https://help.ubuntu.com/community/XenProposed, and I'd like to setup a static IP address, but I don't know how. I'm using 12.04 Server. This is the step I'm having trouble at (I'm using eth1): Edit /etc/network/interfaces, and make it look like this: auto lo iface lo inet loopback auto xenbr0 iface xenbr0 inet dhcp bridge_ports eth0 auto eth0 iface eth0 inet manual I do this, and here is my output from ifconfig: eth1 Link encap:Ethernet HWaddr 00:17:a4:f8:79:20 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:478264 errors:0 dropped:0 overruns:0 frame:0 TX packets:2895 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:46470058 (46.4 MB) TX bytes:214620 (214.6 KB) Interrupt:17 Memory:fa000000-fa012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) xenbr0 Link encap:Ethernet HWaddr 00:17:a4:f8:79:20 inet addr:192.168.1.122 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::217:a4ff:fef8:7920/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:471842 errors:0 dropped:0 overruns:0 frame:0 TX packets:2795 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:37005780 (37.0 MB) TX bytes:182010 (182.0 KB) So how do I give this system a static IP address? Sorry, I'm not that familiar with networking on Ubuntu.

  Read the article

• Trying to format drive fails

  - by david

  since I will be doing an internship for which i need to use Windows software, I have decided to ruin my day trying to remove my Ubuntu 12.04, install Win XP SP3 (since the DualBoot theme from ubuntu suggests to first install Windows and then Ubuntu, for problems with the bootloader if you do it the other way around) and then reinstall Ubuntu 12.04 since I would like to keep using it as my primary operating system, using WinXP exclusively for the internship. Other than that, I would like to have a partition for the data, which can be used by both Ubuntu and Windows. So now, I have used the disk utility run from an ubuntu-live cd to format my drive with Master Boot Record (being conscious of the fact that this way I will lose all my data, which I have saved on an external drive before, and that my Ubuntu won't work anymore afterwards), creating partitions for Windows (NTFS), personal data (FAT, since as far as I know both Ubuntu and Windows can deal with this), a Swap partition for Linux, and one partition for Ubuntu (ext4); trying to install Win XP from cd gives me a blue screen, which stops the setup and telling me to remove all recently installed drives and to run CHKDSK. So I thought, that maybe Windows doesn't like pre-partitioned drives for its installation and thus I need to re-format my hard drive in order to have a completely "new" drive, which I can then, during the Windows-installation, partition in order to create the partitions I need. Trying to do this, though, the disk-utility run from the live-CD gives me this warning: Error creating partition table: helper exited with exit code 1: In part_create_partition_table: device_file=/dev/sda, scheme=0 got it got disk committed to disk BLKRRPART ioctl failed for /dev/sda: Device or resource busy I do not understand why it tells me that the hard-drive is busy, because, as stated above, I am doing all this from a live-CD. Thus, my questions are: How can I resolve the error given by the disk utility? Does it make sense to use four partitions in the way mentioned above? And if not so, which partitions should I create? Can I, theoretically, partition my drive from an Ubuntu live-cd in order to create the partitions I want and to install first Windows and then Ubuntu? Thanks for any help, David

  Read the article

• Windows 2012 Server Hyper-V: Cannot see LAN

  - by Samuel

  I have one NIC on the machine loaded XP on the Hyper-V and had chosen the network as virtual switch. No LAN and no internet shows up on the client. Am I missing something? it used to work in 2008-R2. Details: One network card on machine (Qualcomm Atheros AR8131 PIC-E Gigabit Ethernet controller) The virtual machine hard disk is pointing to and existing XP-SP2 hard disk created using VPC 2007 The Virtual machine Network Adapter is setup as Virtual Switch to the real ethernet controller with Enable virtual LAN identification set to 2 (no other virtual machine is created in the system) After the virtual machine boots LAN shows empty in Control Panel Network Connections (this is XP client) and I also cannot access the internet. XP is showing activation prompt but as far as I know it should not disable the network! Virtual network switch is set to External

  Read the article

• sql server 2008 snapshot agent problem

  - by Dmitri

  Hi! I've just installed mssql 2008 sp1 x64 on windows 7 RTM, and have the problem with creating snapshots, whenever I try to launch the snapshot agent (i.e. to setup transactional replication publication), it throws the error that 'the file is missing'. I have looked into c:\program files\microsoft sql server\100\com and there are no executable files at all, like snapshot.exe! I tried a crazy move to copy all the files from my mssql 2005 com folder, without replacing ofcourse, and now it doesn't give an error, but says 'starting' all the time, but nothing happens. (Now I have removed those files again) I have all of the relevant features installed. So please help me figure out what to do now! Thanks! Dmitri.

  Read the article

• How to manage a multiplayer asynchronous environment in a game

  - by Phil

  I'm working on a game where players can setup villages, which can contain defending units. Any of these units (each on their own tiles) can be set to "campaign" which means they are no longer defending but can now be used to attack other villages. And each unit on a tile can have up to a 100 health. So far so good. Oh and it's all asynchronous so even though the server will be aware that your village is being attacked, you won't be until the attack is over. The issue I'm struggling with, is the following situation. Let's say a unit on a tile is being attacked by a player from another village. The other player see's your village and is attacking your units. You don't know this is happening though, so you set your unit to campaign and off you go to attack another village, with the unit which itself is actually being attacked by this other player. The other player stops attacking your village and leaves your unit with say a health of 1, which is then saved to the server. You however have this same unit are attacking another village with it, but now you discover that even though it started off with a 100 health, now mysteriously it only has 1... Solutions? Ideas? Edit The simplest solutions are often the best. I referred to Clash of clans below, well after a bit more digging it seems that in CoC you can only attack players that are offline! ha, that almost solves the problem. I say almost because there's still the situation where a players village could be in the process of being attacked when they come back online, still need to address that. Edit 2 A solution to the "What happens when a player is attacking your village and you come online" issue, could be the attacking player just get's kicked out of the village at that point and just get's whatever they had won up to that point, it's a bit of a fudge but it might work.

  Read the article

• Win 2008 R2 Server Not Recognizing Second Hard Drive

  - by Brian

  Hello, I just purchased a Dell server, which has two hard drives and no RAID setup. I can only currently see one hard drive... not sure how to get it to recognize the other, as I thought being a new machine that wouldn't be an issue. It has Windows Server 2008 R2 that I loaded on. I'm a n00b to all of this so I'm not sure why this is failing to work... Any help appreciated. Thanks.

  Read the article

• DIR 601 No wireless internet

  - by ashley

  I have an orange globe on my d link router. I signed into 192.168.0.1 and went to Manuel Internet Connection Setup as I was told to do. When I clicked on that and tried to clone my PC's MAC address, it said invalid MAC address. Host Name : DIR-601 Use Unicasting : (compatibility for some DHCP Servers) Primary DNS Address : 0.0.0.0 Secondary DNS Address : 0.0.0.0 MTU : (bytes) MTU default = 1500 MAC Address : F8:1E:DF:EA:38:E6 How do I get a valid MAC address so I can save the settings and move on to the next steps I was told to do in order to get wireless internet again?

  Read the article

• How can I get Transaction Logs to auto-truncate after Backup

  - by Yaakov Ellis

  Setup: Sql Server 2008 R2, databases set up with Full recovery mode. I have set up a maintenance plan that backs up the transaction logs for a number of databases on the server. It is set to create backup files in sub-directories for each database, verify backup integrity is turned on, and backup compression is used. The job is set to run once every 2 hours during business hours (8am-6pm). I have tested the job and it runs fine, creates the log backup files as it should. However, from what I have read, once the transaction log is backed up, it should be ok to truncate the transaction log. I do not see any option for doing this in the Sql Server Maintenance Plan designer. How can I set this up?

  Read the article

• Remote desktop use two out of four monitors

  - by William Gant

  I've recently upgraded my home workstation and now have four monitors on it. I work remotely most of the time and need some way to get remote desktop onto only two of those four monitors. The top two monitors (monitors 4 & 3, going from left to right) each have a maximum resolution of 1680x1050. The bottom two monitors (1 & 2) each have a maximum resolution of 1920x1080. In my .rpd file for this remote desktop connection, I have the following keys (I've clipped it for brevity) screen mode id:i:2 use multimon:i:1 desktopwidth:i:1920 desktopheight:i:2130 session bpp:i:32 winposstr:s:0,1,3,75,1655,675 Previously I was able to get away with just doing "mstsc /span" when I had only two monitors, but that isn't working now (and isn't desirable). I'd like for the new setup to only use two of my monitors. I don't really care which two. How do I alter the .rdp file to accomplish this?

  Read the article

• activesync not working with forms based authentication

  - by Chad

  I have an Exchange 2003 SP2 single backend server with an SSL cert. I was having trouble getting OMA to work so I found a MS article about making a reg hack and creating a new Exchange-OMA virtual directory. I am able to connect and access content from my mailbox by using secure mail.domainname.com/oma and using my credentials. ActiveSync was not working on a Windows mobile phone or iPhone. I found another article about using Forms Based Authenication and SSL on a single Exchange server environment and the fix was to elliminate FBA and SSL for the Exchange virtual directory. That allows ActiveSync to now work. I have very few mobile users, but they are management, so I need to make ActiveSync work but I would like to get back to using SSL. http://support.microsoft.com/kb/817379 Any ideas about this setup? Thanks.

  Read the article

• Using Lighttpd: apache prox or direct connection?

  - by Halfgaar

  Hi, I'm optimizing a site by using lighttpd for the static media. I've found that a recommended solution is to use Apache Proxy to point to the lighttpd server. But, does that use up an Apache thread/process per request? In my setup, I've noticed that all my processes are used up, even though they aren't doing anything, CPU wise. To free up apache processes, I've configured lighttpd and the amount of processes needed is lowered significantly, Munin shows. However, I've set it up to connect directly to lighty, to prevent apache workers from server static media. My question is: when using Apache Proxy, does that also use up a process/worker?

  Read the article

• Converting my PC to a server

  - by Sean87

  I live in a university campus and luckly I have super fast internet in my room, with a static IP address. I tried to setup XAMPP and by pointing to my IP address from anywhere I can access the services running on my PC. Now I am thinking of hosting my own website on my own PC. I am not sure what else I will need (beside the static IP) to make this happen (if it is possible at all). I am running Windows 7 ultimate and of course I do have a domain registered. What should I point my domains DNS names to make this happen (I assume it is far more steps involved!)

  Read the article

• How can I make my FireFox Browser AddOn Backwards Compatible?

  - by bwheeler96

  I'm making a firefox browser add-on, and I just got all of the code working fine, but it will only install in FireFox 16, and I want it to be compatible at least from 10+, has anyone dealt with this issue? I have my package.json pointing to my install.rdf, and my install.rdf clearly states target applications. Is there any additional setup I need? here is my package.json { "name": "firefox-ext", "license": "MPL 2.0", "author": "", "version": "0.1", "fullName": "firefox-ext", "id": "jid1-AMCw25iQJof53w", "description": "a basic add-on" } and here is my install.rdf. <?xml version="1.0"?> <RDF xmlns="http://www.w3.org/1999/02/22-rdf-syntax-ns#" xmlns:em="http://www.mozilla.org/2004/em-rdf#"> <Description about="urn:mozilla:install-manifest"> <em:id>jid1-AMCw25iQJof53w</em:id> <em:name>Generic App</em:name> <em:version>1.0</em:version> <em:type>2</em:type> <em:creator>Brian Wheeler</em:creator> <em:description>Good Stuff</em:description> <em:targetApplication> <Description> <em:id>{ec8030f7-c20a-464f-9b0e-13a3a9e97384}</em:id> <em:minVersion>1.0</em:minVersion> <em:maxVersion>19.0</em:maxVersion> </Description> </em:targetApplication> </Description> </RDF> I'm using the CFX CLI Tools to make this, so everything has been built and tested with cfx init, cfx run, and cfx xpi I just can't figure out compatibility with anything other than 16. Also, major bonus points if someone could explain the advantages of a rapid release cycle, because it really seems to have shot 3rd party Mozilla developers in the foot in terms of software compatibility. Thanks, -Brian

  Read the article

• New security configuration flag in UCM PS3

  - by kyle.hatlestad

  While the recent Patch Set 3 (PS3) release was mostly focused on bug fixes and such, a new configuration flag was added for security. In 10gR3 and prior versions, UCM had a component called Collaboration Manager which allowed for project folders to be created and groups of users assigned as members to collaborate on documents. With this component came access control lists (ACL) for content and folders. Users could assign specific security rights on each and every document and folder within a project. And it was possible to enable these ACL's without having the Collaboration Manager component enabled. But it took some special instructions (see technote# 603148.1) and added some extraneous pieces still related to Collaboration Manager. When 11g came out, Collaboration Manager was no longer available. But the configuration settings to turn on ACLs were still there. Well, in PS3 they've been cleaned up a bit and a new configuration flag has been added to simply turn on the ACL fields and none of the other collaboration bits. To enable ACLs: UseEntitySecurity=true Along with this configuration flag to turn ACLs on, you also need to define which Security Groups will honor the ACL fields. If an ACL is applied to a content item with a Security Group outside this list, it will be ignored. SpecialAuthGroups=HumanResources,Legal,Marketing Save the settings and restart the instance. Upon restart, two new metadata fields will be created: xClbraUserList, xClbraAliasList. If you are using OracleTextSearch as the search indexer, be sure to run a Fast Rebuild on the collection. On the Check In, Search, and Update pages, values are added by simply typing in the value and getting a type-ahead list of possible values. Select the value, click Add and then set the level of access (Read, Write, Delete, or Admin). If all of the fields are blank, then it simply falls back to just Security Group and Account access. As for how they are stored in the metadata fields, each entry starts with it's identifier: ampersand (&) symbol for users, "at" (@) symbol for groups, and colon (:) for roles. Following that is the entity name. And at the end is the level of access in paranthesis. e.g. (RWDA). And each entry is separated by a comma. So if you were populating values through batch loader or an external source, the values would be defined this way. Detailed information on Access Control Lists can be found in the Oracle Fusion Middleware System Administrator's Guide for Oracle Content Server.

  Read the article

• Raid0 performance degradation?

  - by davy8

  Not sure if this belongs here or on SuperUser, feel free to move as appropriate. I've noticed the performance on my RAID0 setup seems to have degraded over the past months. The throughput is fine, but I think the random access time has increased or something. In use I generally see about 1-5mb/sec when loading stuff in Visual Studio and other apps and it doesn't seem like the CPU is bottlenecking as the CPU utilization is pretty low. I don't recall what Access Time used to be, but HD Tune is reporting 12.6ms Read throughput is showing as averaging about 125MB/sec so it should be great for sequential reads. Defrag daily and it shows fragmentation levels low, so that shouldn't be an issue. Additional info, Windows 7 x64, Intel raid controller on mobo, WD Black 500GB (I think 32mb cache) x2.

  Read the article

• Raid0 performance degradation?

  - by davy8

  Not sure if this belongs here or on SuperUser, feel free to move as appropriate. I've noticed the performance on my RAID0 setup seems to have degraded over the past months. The throughput is fine, but I think the random access time has increased or something. In use I generally see about 1-5mb/sec when loading stuff in Visual Studio and other apps and it doesn't seem like the CPU is bottlenecking as the CPU utilization is pretty low. I don't recall what Access Time used to be, but HD Tune is reporting 12.6ms Read throughput is showing as averaging about 125MB/sec so it should be great for sequential reads. Defrag daily and it shows fragmentation levels low, so that shouldn't be an issue. Additional info, Windows 7 x64, Intel raid controller on mobo, WD Black 500GB (I think 32mb cache) x2.

  Read the article

• Windows 7 Activation with Bootcamp and VMWare

  - by Jason Hernandez

  I have windows 7(64) installation setup on a Boot Camp partition on my MacBook Pro 13". I also access this partition through VMware hosted by OS X (snow leopard). Every time I switch between VMware and Boot Camp windows says that it needs to be re-activated because of hardware or driver changes. I've tried wmware KB KB 1003426 to no avail. Edo Thanks, Jason Edit, I am using the most recent VMware and tools. I've tried "KB 1004917" as well. No Dice. I'm considering re-installing at this point.

  Read the article

• Wireless card not found on Ubuntu

  - by Idealflip

  Hello all, I'm trying to setup Ubuntu on an old PC. I ran the following command, lspci, in order to get info on the wireless card installed. 00:0a.0 Ethernet controller: Marvell Technology Group Ltd. 88w8335 [Libertas] 802.11b/g Wireless (rev 03) Does anyone know where I can get drivers for this card/chip? And also, how to install (I'm rather new to linux). Also, I'm sure the card is working because I just formatted over xp, and everything was working well. Thanks in advanced!

  Read the article

• Unit testing ASP.NET Web API controllers that rely on the UrlHelper

  - by cibrax

  UrlHelper is the class you can use in ASP.NET Web API to automatically infer links from the routing table without hardcoding anything. For example, the following code uses the helper to infer the location url for a new resource,public HttpResponseMessage Post(User model) { var response = Request.CreateResponse(HttpStatusCode.Created, user); var link = Url.Link("DefaultApi", new { id = id, controller = "Users" }); response.Headers.Location = new Uri(link); return response; } That code uses a previously defined route “DefaultApi”, which you might configure in the HttpConfiguration object (This is the route generated by default when you create a new Web API project). The problem with UrlHelper is that it requires from some initialization code before you can invoking it from a unit test (for testing the Post method in this example). If you don’t initialize the HttpConfiguration and Request instances associated to the controller from the unit test, it will fail miserably. After digging into the ASP.NET Web API source code a little bit, I could figure out what the requirements for using the UrlHelper are. It relies on the routing table configuration, and a few properties you need to add to the HttpRequestMessage. The following code illustrates what’s needed,var controller = new UserController(); controller.Configuration = new HttpConfiguration(); var route = controller.Configuration.Routes.MapHttpRoute( name: "DefaultApi", routeTemplate: "api/{controller}/{id}", defaults: new { id = RouteParameter.Optional } ); var routeData = new HttpRouteData(route, new HttpRouteValueDictionary { { "id", "1" }, { "controller", "Users" } } ); controller.Request = new HttpRequestMessage(HttpMethod.Post, "http://localhost:9091/"); controller.Request.Properties.Add(HttpPropertyKeys.HttpConfigurationKey, controller.Configuration); controller.Request.Properties.Add(HttpPropertyKeys.HttpRouteDataKey, routeData);  The HttpRouteData instance should be initialized with the route values you will use in the controller method (“id” and “controller” in this example). Once you have correctly setup all those properties, you shouldn’t have any problem to use the UrlHelper. There is no need to mock anything else. Enjoy!!.

  Read the article

• What is the best way to configure Apache or AWS to support a Rails multi tenancy application that allows each customer to have their own domain name?

  - by Ryan Arneson

  I'm building a Rails 3 SaaS site that allows for multi-tenancy. When a customer signs up they put in their own domain name, e.g. example.com. I need example.com to point to my SaaS application and serve them their content. My questions are as follows: Do I need to create an Apache vhost for each customer using their own domain? Is there an easier way with CNAME's to just have the customer point to the IP address of my server(s) that then forwards the request onto my application through some catch all vhost? Would I be able to create the CNAME record for the customer so they don't have to do any setup? Would this be a case better suited to Amazon Web Services? Any help or explanation or corrections on my understanding of dns would be appreciated. I'm a developer so the server ops portion of this is a bit cloudy.

  Read the article

• links for 2010-12-15

  - by Bob Rhubart

  Pravin Janardanam: Security in OBIEE 11g, Part 1 Guest blogger Pravin Janardanam kicks off a two-part series in which he tackles the differences in security between OBIEE 11g and 10g, and provides some hints on security migration from a 10g environment. (tags: oracle otn businessintelligence obiee) HttpClusterServlet Configuration (Weblogic Server Acting as a Proxy) Quick tips from Divay Dureja. (tags: oracle weblogic servlet configuration) Accelerating Deployment of Virtualized Infrastructures with the Oracle VM Blade Cluster Reference Configuration "The Oracle VM blade cluster reference configuration is a single-vendor solution that addresses every layer of the virtualization stack with Oracle hardware and software components." - from the white paper. (tags: oracle otn oraclevm virtualization) A SOA Safari (Antony Reynolds' Blog) SOA author Antony Reynolds shares links to some of his favorite SOA titles available for reading on Safari. (tags: oracle otn soa) Using Crossbow and Solaris 11 Express Zones for a single machine proof of concept environment with Puppet "My last blog entry was about my debugging experience with Puppet and promise to share the setup that I used. I now follow up that previous entry with this one which describes my Crossbow + NAT + S11 Zones proof of concept." - Michael Tin (tags: oracle solaris crossbow) @myfear: One thing you did not know about Java EE class loading in GlassFish 2.x "Be careful migrating apps from one app server to the other. And don't expect to have a strong hierarchical class loader in place. That is especially true for GF 2.x class loading." Oracle ACE Director Markus Eisele (tags: oracle otn oracleace java glassfish weblogic)

  Read the article

• ATG Live Webcast March 29: Diagnosing E-Business Suite JVM and Forms Performance Issues (Performance Series Part 4 of 4)

  - by BillSawyer

  The next webcast in our popular EBS series on performance management is going to be a showstopper.  Dave Suri, Project Lead, Applications Performance and Gustavo Jimenez, Senior Development Manager will discuss some of the steps involved in triaging and diagnosing E-Business Suite systems related to JVM and Forms components. Please join us for our next ATG Live Webcast on Mar. 29, 2012: Triage and Diagnostics for E-Business Suite JVM and Forms The topics covered in this webcast will be: Overall Menu/Sections Architecture Patches/Certified browsers/jdk versions JVM Tuning JVM Tools (jstat,eclipse mat, ibm tda) Forms Tools (strace/FRD) Java Concurrent Program options location Case studies Case Studies JVM Thread dump case for Oracle Advanced Product Catalog Forms FRD trace relating to Saving an SR Java Concurrent Program for BT Date:               Thursday, March 29, 2012Time:              8:00 AM - 9:00 AM Pacific Standard TimePresenters:  Dave Suri, Project Lead, Applications Performance                        Gustavo Jimenez, Senior Development ManagerWebcast Registration Link (Preregistration is optional but encouraged)To hear the audio feed:   Domestic Participant Dial-In Number:            877-697-8128    International Participant Dial-In Number:      706-634-9568    Additional International Dial-In Numbers Link:    Dial-In Passcode:                                              99342To see the presentation:    The Direct Access Web Conference details are:    Website URL: https://ouweb.webex.com    Meeting Number:  597073984 If you miss the webcast, or you have missed any webcast, don't worry -- we'll post links to the recording as soon as it's available from Oracle University.  You can monitor this blog for pointers to the replay. And, you can find our archive of our past webcasts and training here.If you have any questions or comments, feel free to email Bill Sawyer (Senior Manager, Applications Technology Curriculum) at BilldotSawyer-AT-Oracle-DOT-com. 

  Read the article

• Windows SBS 2011 DNS Role (service) failing & needing restarting

  - by HaydnWVN

  Have a Windows SBS 2011 with Exchange that is handling all DNS for the network. Since getting a 3rd party (Hardware & Support) to setup a recieving FTP service and restricting Exchanges memory useage for another 3rd party product (Stock software) the local network seems to periodically 'lose the internet connection'. Delving deeper I found that the DNS service is somehow failing/stopping without the actual service on the server reporting such (nothing in event logs). A simple restart of the 'DNS Role' on the server solves the problem. The manager onsite reports that he has to do this most days in the afternoon - yet not at the same time and other days it works fine without a restart being required. I'm unable (lacking sufficient SBS2011 knowledge) to diagnose this further, ideally I would like the DNS Role to report (and log) the failure, then automatically restart itself.

  Read the article

• N64oid Brings N64 Emulation to Android Devices

  - by ETC

  Craving some Ocarina of Time adventures, Super Mario 64 antics, or some Star Fox 64 flying on your Android device? N64oid brings retro emulation of Nintendo’s popular N64 console to Android devices. N64oid is an N64 console emulator for Android devices. You’ll need a copy of the $5.99 emulator, ROMs (from the usual sources, unless you’ve got a ROM ripping setup in your basement and a stack of old cartridges), and a suitably speedy Android device. Older Android devices will find the playback choppy and subpar, but newer and speedier devices like the Nexus-One and Samsung Galaxy should have no problem handling the emulator. Like all emulators N64oid is a work in progress and emulating an entire closed-system console on a totally different set of hardware is never a perfect 1:1 emulation, but if you’re a die hard fan of classic N64 titles (check out this list of top ranked titles to inspire some nostalgia) N64oid is worth the price of a burger for sure. N64oid [Android Market via Download Squad] Latest Features How-To Geek ETC Learn To Adjust Contrast Like a Pro in Photoshop, GIMP, and Paint.NET Have You Ever Wondered How Your Operating System Got Its Name? Should You Delete Windows 7 Service Pack Backup Files to Save Space? What Can Super Mario Teach Us About Graphics Technology? Windows 7 Service Pack 1 is Released: But Should You Install It? How To Make Hundreds of Complex Photo Edits in Seconds With Photoshop Actions Super-Charge GIMP’s Image Editing Capabilities with G’MIC [Cross-Platform] Access and Manage Your Ubuntu One Account in Chrome and Iron Mouse Over YouTube Previews YouTube Videos in Chrome Watch a Machine Get Upgraded from MS-DOS to Windows 7 [Video] Bring the Whole Ubuntu Gang Home to Your Desktop with this Mascots Wallpaper Hack Apart a Highlighter to Create UV-Reactive Flowers [Science]

  Read the article

< Previous Page | 474 475 476 477 478 479 480 481 482 483 484 485  | Next Page >