Search Results

Search found 16472 results on 659 pages for 'computer scientist'.

Page 479/659 | < Previous Page | 475 476 477 478 479 480 481 482 483 484 485 486  | Next Page >

• PackageForTheWeb "should not be executed directly"

  - by Sergei Ousynin

  When trying to install package (specifically, chipset drivers for Nexcom PEAK-series computer, but I guess it doesn't really matters) I get "PackageForTheWeb Error" saing "This program is used internally by PackageFromTheWeb. It should not be executed directly." I get this error on both Windows 2000 (where it should be installed) and Windows 7. The original driver CD was lost long time ago, so the package was downloaded from the Nexcom website, found no info about installer prerequisites there. What should I install (or anything else) to install this package? UPD: I found a solution - unpacked the package and executed setup.exe that was inside. But I'm pretty sure it's not an action supposed by vendor, so answers are still welcome.

  Read the article

• Why does HDTune report better performing drives 2 months after installing them?

  - by Rolnik

  OK, so this is really weird. I ran HDTune on a newly set-up home-built computer and got the following readings from my drives in mid-November. SSD 154 MB/s RAID1 87 RAID0 198 (software installs) RAID0 98 Swap drive Today, in January, I run HDTune (same version) and get these results, in MB/s: SSD 186 RAID1 98 RAID0 241 RAID0 98 (Swap drive) Here are more details that HDTune reports on the SSD drive: HD Tune: OCZ-VERTEX Benchmark Blockquote Transfer Rate Minimum : 135.4 MB/sec Transfer Rate Maximum : 219.4 MB/sec Transfer Rate Average : 185.7 MB/sec Access Time : 0.1 ms Burst Rate : 187.3 MB/sec CPU Usage : -1.0% To get to my question: Why are my hard drives improving in performance? Most of my logical drives are in some form of RAID, except for the SSD. Will this performance ever deteriorate? Note, none of my drives are a hybrid drive that uses some form of SSD to enhance the write/reads on actual platters.

  Read the article

• Best Configuration For Youtube HD 720p

  - by Eray Alakese

  Hello, I'm recording a screencast with CamStudio (http://camstudio.org/) . My computer's screen resolution is 1280*800 , so video's resolution is 1280*800, too. I'm using Microsoft Video 1 codec when recording. I was record 9 minutes video and this video's size is 214 MB . I will upload this video to Youtube. I'm coding a web site at the video, because of this, video must be quality (720p) . I want to reduce file's size, before upload . I'm using Total Video Converter (http://www.effectmatrix.com/total-video-converter/) . But when i convert to FLV , video's size increase to 250MB :) I don't know, how can i configure this setting and which file type should i choose. (screenshot here : http://i.imgur.com/Se0EP.jpg )

  Read the article

• Best Configuration For Youtube HD 720p

  - by Eray Alakese

  Hello, I'm recording a screencast with CamStudio . My computer's screen resolution is 1280*800 , so video's resolution is 1280*800, too. I'm using Microsoft Video 1 codec when recording. I was record 9 minutes video and this video's size is 214 MB . I will upload this video to Youtube. I'm coding a web site at the video, because of this, video must be quality (720p) . I want to reduce file's size, before upload . I'm using Total Video Converter . But when i convert to FLV , video's size increase to 250MB :) I don't know, how can i configure this setting and which file type should i choose.

  Read the article

• What are my X client options for MS Windows?

  - by Nick Bolton

  I need to connect to a headless X Windows server (running on Ubuntu) from my MS Windows 7 computer over a 100 Mbit network. I could use VNC (or any other remote viewer) but the 3D graphics performance would be lousy I imagine. I used to have it hooked up to a monitor, but that's broken now and I can't afford a new one. A friend advised that I could try and use an X client, and that the 3D graphics wont suffer too much over 100 Mbit. Cygwin seems to be an option, but I was wondering if there were any more lightweight options.

  Read the article

• How to load previous kernel via ssh?

  - by Aamir

  I work remotely on my work computer. I am also the root of the workstation that I am sharing with my colleague. Yesterday, I upgraded the kernel to 2.6.31-17 when asked by the update manager but refrained from restarting because I knew my NVIDIA and several other kernel modules wouldn't work. Unfortunately my colleague who is a linux noob restarted the machine and here I am :( I am thinking of changing the symlinks /initrd.img and /vmlinuz to the previous kernel image and use kexec. Please tell some better way to load the 2.6.31-16 release of kernel from ssh and not the grub boot menu. I am using Ubuntu Karmic.

  Read the article

• What is a safe way to dispose of personal info on an old laptop and what to do with said laptop?

  - by MikeN

  I have an old laptop someone gave me that only has 64Megs of RAM on it and runs WIN XP. I wanted to wipe the drive clean by installing Ubuntu Desktop to remove any shred of personal information on it and to make it useful to someone else. But the Ubuntu installer keeps failing because there is not enough RAM. Is there another version of Linux that would easily install on a 64 Megs of RAM system? 2nd part of question, what do I do with this old laptop? It doesn't have a battery anymore and has to be plugged into the wall to run. Assuming I can install a good Linux distro on it, who do I give it to? Salvation Army? I'm looking to just have it be useful to someone or some organization for spare parts or some basic computer usage.

  Read the article

• Launching multiple applications with a single command/script/shortcut

  - by Bill

  I realized a few days ago that every time I sit down at work, I do a few things after unlocking my computer. First, I open up Firefox, then I open up Chrome, then I log in to Digsby. I realized I could probably save repeating this daily by writing a small batch script to open up Firefox and Chrome , but I couldn't figure out how to make it work.. and since the whole effort is to save time I don't want to bash my head around in the windows command prompt to do it. I also tired this in powershell but ran in to a bunch of security nonsense. Is there a way to do this that I am missing? Bonus points if somebody has figured out how to manipulate Digsby via COM , scripting, or python =)

  Read the article

• My pendrive is not working and showing Unknown file System

  - by Debabratta

  I have a pendrive when I insert it into one o my port it shows in the My Computer but when I try to explore, it shows please insert a disk into drive H. However my usb drive is well inserted. I tried to format it but it is showing There is no disk in drive H, Insert a disk then try again. Its properties is showing Unknown File System and the used space and free space part showing 0 bytes. I cann't also check for errors in the drive. Its device status:The device is working properly. I also reinstalled the driver but that did not help me. Please suggest some way to recover the issue. Thanks.

  Read the article

• PGP - MailCloak/Gpg4Win/etc

  - by ericl42

  Hello, I have used Gpg4Win in the past along with FireGPG to have encryption on my emails. I am needing to roll this out to quite a few more people and was wondering if anyone else had some products they preferred better. The criteria I need is free and as user friendly as possible. I looked at MailCloak but I have had some issues with it on 1 of the 2 computers I've been testing on. It seems like it might work pretty well as a overall solution but on my computer I keep getting "Identity cannot be created." and not sure whats going on with that. Thanks for the info.

  Read the article

• Install Rails on linux [migrated]

  - by Jseb

  I am trying to install Ruby on Rails. and i have followed the following link for the install https://www.digitalocean.com/community/articles/how-to-install-ruby-on-rails-on-ubuntu-12-04-lts-precise-pangolin-with-rvm. This link was helpful i was able to run it, and everything, however as soon has i restarted the computer i then go into my apps and run it again with rails s and this message occurs. The program 'rails' is currently not installed. You can install it by typing: sudo apt-get install rails But work before, what should i do, do i need to set the path of somesort?? I am not that great in linux so bear with me. I am using linux ubuntu 12.04 desktop and my user is john Thanks in advance

  Read the article

• Two users using the same same user profile while not in a domain.

  - by Scott Chamberlain

  I have a windows server 2003 acting as a terminal server, this computer is not a member of any domain. We demo our product on the server by creating a user account. The person logs in uses the demo for a few weeks and when they are done we delete the user account. However every time we do this it creates a new folder in C:\Documents and Settings\. I know with domains you can have many users point at one profile and make it read only so all changes are dumped afterwords, but is there a way to do that when the machine is not on a domain? I would really like it if I didn't have to remote in and clean up the folders every time.

  Read the article

• Install Office software on a standard user account automatically.

  - by Earls

  If I know the Administrator account name and password on a Windows 7 computer, would it be possible to create an Office 2010 install CD that would "silently" install Office 2010 on a standard user account which does not have installation privileges. As in, the group policy "always install with elevated privileges" is in effect for the user. Some way to built the admin account privileges into the office installer? VBS Script? CMD? Understand, the laptops are in the field, the end user doesn't have the admin password and can't have the admin password. Thanks.

  Read the article

• Why can't I create a Windows backup on my secondary disk?

  - by Brian Sullivan

  I've installed Windows 7 Ultimate on an SSD that I've added to the XPS desktop that I bought from Dell. I would like to use the built-in backup functionality to create incremental backups and store them on the large drive that came with the machine. I formatted the large drive and turned it into a Basic disk. However, when I try to set the backup location to the large internal disk (E:\) in the "Set up backup" wizard, a get a message saying, "A system image cannot be saved on a drive that your computer boots from or that Windows is installed on." Windows is not installed on that disk. I even deleted the OEM partition that was on the disk, and removed it completely from the boot order in the BIOS. Any clue why Windows is griping at me about this?

  Read the article

• Why do most routers not include local DNS?

  - by user785194

  I need to change my firewall/router, and I'd prefer something with built-in DNS to resolve queries on the local subnets. I've got a mixed Linux/Windows system, often with only one computer turned on, and I frequently have problems resolving local names. I don't want to keep a Linux box permanently on just for DNS, and I'd prefer to have DNS in my router appliance, which is always on. I search Google for this occasionally but never find anything. You always get the obvious answers - it's not possible, put everything in /etc/hosts, NetBIOS, dedicated box, etc. So what am I missing? Why don't "cheap" routers let you do this? I'm pretty sure that Cisco kit does this. Almost all cheap routers will let you do MAC address reservation, to let them assign static IP addresses for DHCP. So why can't they simply do DNS as well for everything on the local subnets, just passing through remote domains to the ISP?

  Read the article

• Truecrypt system partion partially encryted but then drive corrupted and won't boot - decrypting so I can access files to backup?

  - by Dr.Seuss

  So I was attempting to encrypt my (Windows 7) system drive with Truecrypt and it stopped at around 15% and said that there was a segment error and that it could not proceed until it was fixed. So, I restarted the computer and ran HDD Regenerator which subsequently fixed the bad sectors on the drive, but now my system cannot boot. So, I run a number of recovery disks to no avail (Windows repair is unable to fix) and the drive won't mount on a linux version run from a CD because the drive is encrypted. So I tried mounting the drive using Truecrypt under the Linux distribution on the disk and selected "Mount partition using system encryption without pre-boot authentication" so I can decrypt, but I get an error message about it only being possible once the entire system is encrypted. How do I get out of this mess? I need to be able to back up the data that's on that partially encrypted drive so I can reinstall my operating system.

  Read the article

• Need help upgrading MacBookPro3,1 RAM to 4GB.

  - by Fantomas

  My questions are: 1) Where to buy it and what to buy? I have heard that this RAM is generic enough and it does not have to come from Apple. 2) Can I reuse my existing stick(s)? Would I have a single 2GB module, or 2 x 1GB modules? 3) If I have 2GB already, is it a good idea to have one old stick and one new one? Which one is better placed at the top and which one at the bottom? Let me know what questions you have. My computer's info: Hardware Overview: Model Name: MacBook Pro Model Identifier: MacBookPro3,1 Processor Name: Intel Core 2 Duo Processor Speed: 2.4 GHz Number Of Processors: 1 Total Number Of Cores: 2 L2 Cache: 4 MB Memory: 2 GB Bus Speed: 800 MHz Boot ROM Version: MBP31.0070.B07 SMC Version (system): 1.16f11

  Read the article

• Ubuntu black screen after Installation of 12.10 Live USB

  - by Lime0fHint

  My computer was made in 2004, but I'm sure it doesn't matter since it's a durable machine. So recently, I decided to breathe new life to it with Linux. I tried Lubuntu 12.10, Nope. Black screen after install. So I tried Ubuntu 12.10 when I gave up, and same exact thing. Except, this time I'm fighting for it, since Ubuntu is the best OS I've ever seen. So back on-topic, when I start the installation, it says that something is already mounted (Sda or something of the sorts) So I just figure that it's the Live USB I'm using. So I let it ignore it, and move on. The rest of the installation goes smooth, all looks fine. Then I get to the screen with the introductory to Ubuntu. Meanwhile, it's still installing, but finishing up. I'm not sure if the install actually finishes, but I do know that after a bit, the screen goes back to the desktop. The install closes and I'm back at the desktop, and the cursor is showing the "loading" symbol, as if it were still working. Then the screen goes black, with the same cursor. After that, nothing. I left it over night like that thinking it was doing something, in the morning it was still black with the cursor circling or whatever. So what could be causing this? One concern I have is that I have a Nvidia graphics card (7300 GT). I heard that Nvidia isn't compatible with Linux? I did notice that it was marked as unreconigsed by Ubuntu, so is that the problem perhaps?

  Read the article

• HP DV6 connects but no internet

  - by Frank Barcenas

  I have a Hewlett Packard DV6. I connected to the access point. I receive an IP address/default gateway/DNS,etc(DHCP). I cannot ping my gateway. DNS lookups fails. There is just no connectivity. My driver is listed as being IWLWIFI. An lspci shows my card to be a Realtek RTL8101E/RTL8102E. I can't ping myself from another computer. eth0 Link encap:Ethernet HWaddr c8:0a:a9:0c:a7:45 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:41 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:561 errors:0 dropped:0 overruns:0 frame:0 TX packets:561 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:42164 (42.1 KB) TX bytes:42164 (42.1 KB) wlan0 Link encap:Ethernet HWaddr 00:26:c7:04:97:c0 inet addr:192.168.1.109 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::226:c7ff:fe04:97c0/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:71 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2035 (2.0 KB) TX bytes:12371 (12.3 KB)

  Read the article

• backuppc - how to backup remote (over the internet) clients?

  - by Scott

  I am testing out backuppc, which works great so far backing up windows clients on a LAN via SMB (no backup client/agent required). However I have quite a few laptops and desktops that are in various remote locations - some of which move around. I need some way to have that remote computer create an outgoing connection for backup purposes (Windows XP/7). I know backuppc supports smb, rsync and 'tar', but I believe these are all connections going from the server TO the client. SO, I either need a way to vpn the client on a timed basis, or it would be a lot better if the client could some how connect to the server (ssh?) and initiate it's own backup somehow (rsync?). Of course this all needs to be pre-installed by me and require no maintenance by the end user, no dialogs on their side. What do you think?

  Read the article

• Are these symptoms of a video card is dying?

  - by K Cloud

  What I am getting from my PC: Scrambled text in the boot menu. The scrambled text dissapears and everthing goes normal after several restarts, or the computer has worked for some time. Display goes blank showing, windows kernel mode driver stopped responding. Sometimes the windows just hangs, I need to restart the pc for that. There used to be some scrambled colors in my windows, so I cleaned up my video carda and port and reinstalled the video card, things are something right. The pc runs normally for hours in safe mode, as diffault display driver works at that case. My PC specs: Core 2 Duo processor 2 GB RAM NVIDIA EN210 SILENT GPU Windows 8 Drivers details: NVIDIA drivers - v331.65, told to be fully compatible with Win8 Currently I am installing Windows 7 and will be putting the older version of driver v320 to test, yet I'm really confused weather my GPU is dying or still on go.

  Read the article

• Need old version Firefox Java plugin

  - by Bryan

  I need to use Java 1.6.0_20 for the software I'm running. I went to the Oracle website and downloaded jre1.6.0_20 and installed it on my computer, but can't seem to get Firefox to load Java. If I download directly from http://www.java.com/en/download/manual.jsp, the plugin works fine but is the wrong version, and I can't find on www.java.com anywhere to download any of the previous versions. According to the help (can't post link because of spam prevention), I need to go into the Java Control Panel and enable it for Mozilla. I've done this multiple times, but every time I go in to the control panel and check the box, click Apply and Save, as soon as I go back in the box is unchecked. Does anyone know either why the box is unchecked, or where I can download the old JRE that also is configured for Firefox?

  Read the article

• Installing Oracle11gr2 on redhat linux

  - by KItis

  I have basic question about installing applications on linux operating system. i am going to express my issue considering oracle db installation as a example. when installing oracle database , i created a user group called dba and and user in this group called ora112. so this users is allowed to install database. so my question is if ora112 uses umaks is set to 077, then no other uses will be able to configure oracle database. why do we need to follow this practice. is it a accepted procedure in application installation on Linux. please share your experience with me. thanks in advance for looking into this issue say i install java application on this way. then no other application which belongs to different user account won't be able use java running on this computer because of this access restriction.

  Read the article

• Random compositing lag

  - by user1020567

  My laptop specs: 512 mb of RAM, out of which 64 mb are shared with an integrated GPU - ATI Radeon Xpress 200 M. Intel 1,6 Ghz Celeron M single-core processor. I've spent months trying to figure out why compositing and effects sometimes lag on any distro I try. Now I've come to realise that no matter what drivers I try (the default ones work for me on pretty much any linux) compositing lag is random. When I used Ubuntu 10.10, for example, sometimes window compositing would lag and sometimes it wouldn't. The PC is able to render those effects so hardware is not the problem. It's completely random and unpredictable - sometimes when I turn on the computer the effects lag horribly and sometimes it's completely smooth. I've also checked startup items and there doesn't seem to be any unnecessary entries. I also tried building my own OS with Arch Linux and the problem persists there, therefore I can only assume that it's a driver issue of some sort. By default there are lots of drivers supplied with linux distributions. Could it be that they're in the way? The ones that I need are ati/radeon (or both? What's the difference between them?) and there seem to be a lot of others... What should I do?

  Read the article

• Update Manager got stuck (but not frozen) while installing downloaded updates. What should I do?

  - by WarriorIng64

  I have just gotten my Ubuntu 12.04 LTS desktop computer reassembled after a trip back home and connected it to my parent's wireless Internet connection. The connection seems quite shaky (disconnects half the time, likely an ongoing issue with the wireless card I have installed), and it struggled to download updates because of the constant interruptions. Eventually, it managed to download the updated packages and started installing them. I got up and left it to do its work. When I came back, I saw it was still having trouble staying connected to the wireless (no surprise there), but then I noticed that it seemed like Update Manager had stopped making progress on the installation. I opened the Details pane to see what it was last doing: My guess was that the installation script for flashplugin-installer couldn't complete the download until I stabilized the Internet connection. I hooked my Ubuntu laptop up to my desktop via Ethernet and shared its wireless connection using this guide, and as I am typing this now from my desktop you can see that the connection issue was successfully worked around. However, even with a stable connection established, Update Manager seems "stuck" at its current position and won't go any further. It's not totally frozen, but I can't do anything beyond open/close the Details pane as the Cancel button is grayed out. I know it can cause big problems if updates are stopped during installation, but I'm at a loss as to how this situation should be handled. I'm sure it should finish normally if I can just find a way to restart Update Manager, but the question is how this should be approached. How can I safely get my updates to finish installing?

  Read the article

< Previous Page | 475 476 477 478 479 480 481 482 483 484 485 486  | Next Page >