Search Results

Search found 19478 results on 780 pages for 'delay load'.

Page 611/780 | < Previous Page | 607 608 609 610 611 612 613 614 615 616 617 618  | Next Page >

  • WAN Optimization for Small Office/Home Office

    - by TiernanO
    I have been reading up on WAN optimization for the last while, mostly out of interest of speeding up my own internet connections, but also to speed up the office internet connection. At home, I have 2 cable modems plugged into a RouterBoard RB750, which load balances the connections. In the office, we have a single connection into a NetGear router. Most of the WAN Optimization products I have seen, seem to be prohibitively expensive, but also seem to be based on the idea of having multiple branches around the world. What I am looking for, ideally, is as follows: software install: I am "guessing" I need to install it in 2 places: one in the office or house, and one in "the cloud". any connections going to, say, The US (we are in Europe, but our backup's live in the US currently, which would be something important to speed up) would be "tunnelled" though the Optimizer. If downloading or uploading large files, open multiple connections between both "the cloud" and the optimizer... This is where a lot of speed could be gained. finally, for items not compressed, they would be compressed on the cloud side of things, also items that are already on the optimizer could be not sent again. kind of like RSync or Proxy servers... So, is there something that can be done? Is it available using off the shelf components (some magic script with SSH, Squid, Linux and duct tape) or is it something that needs to be purchased? or even an Open Source Project that does 90% of what i am asking?

    Read the article

  • IP to IP forwarding with iptables [centos]

    - by FunkyChicken
    I have 2 servers. Server 1 with ip 1.1.1.1 and server 2 with ip 2.2.2.2 My domain example.com points to 1.1.1.1 at the moment, but very soon I'm going to switch to ip 2.2.2.2. I have already setup a low TTL for domain example.com, but some people will still hit the old ip a after I change the ip address of the domain. Now both machines run centos 5.8 with iptables and nginx as a webserver. I want to forward all traffic that still hits server 1.1.1.1 to 2.2.2.2 so there won't be any downtime. Now I found this tutorial: http://www.debuntu.org/how-to-redirecting-network-traffic-a-new-ip-using-iptables but I cannot seem to get it working. I have enabled ip forwarding: echo "1" > /proc/sys/net/ipv4/ip_forward After that I ran these 2 commands: /sbin/iptables -t nat -A PREROUTING -s 1.1.1.1 -p tcp --dport 80 -j DNAT --to-destination 2.2.2.2:80 /sbin/iptables -t nat -A POSTROUTING -j MASQUERADE But when I load http://1.1.1.1 in my browser, I still get the pages hosted on 1.1.1.1 and not the content from 2.2.2.2. What am I doing wrong?

    Read the article

  • Issue with kernel boot [OVH SERVER]

    - by Conner Stephen McCabe
    Trying to install OpenVZ kernel on Centos 6.3, Yes my kernel is installed i can see it in the /boot folder, yes it is Rhel6 and yes it is all up to date, i checked this with yum update. My issue comes when i reboot my server with that kernel set as the default, it doesn't load, below i shall put a copy of my grub.conf file and my menu.lst file. Grub.conf: default=0 timeout=5 title vzkernel (2.6.32-042stab057.1) root (hd0,0) kernel /boot/vmlinuz-2.6.32-042stab057.1 ro root=/dev/sda1 initrd /initramfs-2.6.32-042stab057.1.img title linux centos6_64 kernel /boot/bzImage-3.2.13-xxxx-grs-ipv6-64 root=/dev/sda1 ro root (hd0,0) Now i shall paste in Menu.lst; # grub.conf generated by anaconda # # Note that you do not have to rerun grub after making changes to this file # NOTICE: You have a /boot partition. This means that # all kernel and initrd paths are relative to /boot/, eg. # root (hd0,0) # kernel /vmlinuz-version ro root=/dev/mapper/vg_stock-lv_root # initrd /initrd-[generic-]version.img #boot=/dev/sda default=0 timeout=5 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu title Linux OpenVZ (vmlinuz-2.6.32-042stab057.1) root (hd0,0) kernel /boot/vmlinuz-2.6.32-042stab057.1 ro root=/dev/mapper/vg_stock-lv_root rd_LVM_LV=vg_stock/lv_root rd_LVM_LV=vg_stock/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFONT=l$ initrd /initramfs-2.6.32-042stab057.1.img title CentOS (2.6.32-71.el6.x86_64) root (hd0,0) kernel /boot/bzImage-3.2.13-xxxx-grs-ipv6-64 ro root=/dev/mapper/vg_stock-lv_root rd_LVM_LV=vg_stock/lv_root rd_LVM_LV=vg_stock/lv_swap rd_NO_LUKS rd_NO_MD rd_NO_DM LANG=en_US.UTF-8 SYSFO$ initrd /initramfs-2.6.32-71.el6.x86_64.img # dummy text Somebody mentioned something about OVH having added a script which changes the kernel settings or something, and suggested that we either remove the script or reinstall using a VNC, but we don't know how to go about doing either of these? Really would be great if you guys could help. Thanks in advance.

    Read the article

  • Problem running “Central Administration” website after windows update at Windows 2003 Server Standar

    - by Magdy Roshdy
    I was have WSS 2.0 and then I upgraded to WSS 3.0 and the old instalation database was SQL 2000, now I have another SQL Server instance called:server_name\MICROSOFT##SSEE . After upgrade every thing works fine and our team started to use the portal and we sent lot of documents and make lot of activities on it. The problem started after installing Windows updates the website suddenly stopped and giving me an error "Cannot connect to the configuration database" If I tried to open SharePoint Products and Technologies Configuration Wizard it is gives me a strange error says: "An exception of type Microsoft.SharePoint.PostSetupConfiguration.PostSetupConfigurationTaskException was thrown. Additional exception information: SharePoint Products and Technologies cannot be configured. The current installation mode does not support SKU to SKU upgrades because there exists an older version of Windows SharePoint Services that must be upgraded first " At this post:http://stackoverflow.com/questions/114398/iis-error-cannot-connect-to-the-configuration-database/249494#249494 the guy of the second answer have the same problem and he suggested a solution but I don't understand well. I tried as he suggested to make the identity of the app pool of the SharePoint web site as "IWAM_server_name " after that the error changed as he said and I web site give me "Server Application Unavailable " and when checked the Event Viewer at the server I found that ASP.NET 2.0 give this exception: "Could not load file or assembly 'System.Web, Version=2.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a' or one of its dependencies. Access is denied ." and I don't know how to solve this problem. I'm really want to make my web site working because our team really need these documents and its stuff. I hope I will find some one to help me.

    Read the article

  • "Dictionary problem." Error with VMPlayer

    - by George Mauer
    I'm pretty new to using vmware virtualization (been a virtualbox user) so I'm hoping you guys can help me out. I recently got an external usb disk containing a vm for a client, downloaded vmplayer, set it up with "Open a Virtual Machine", ran it, easy as pie. After working with it a bit this morning, I shut the VM down and now trying to start it back up again I get this: I tried removing the vm from my library, now it happens whenever I try to add it back in. In the meantime, I can still access other virtual machines so it seems like the problem might be with the virtual disk. So two questions: This is obviously not a very helpful error message. Where can I go to get more information? My Application EventLog doesn't contain anything from VMWare. What steps can I take to fix the problem? Edit: A couple more pieces of information. I did not take any snapshots. I don't think VM Player even has that ability. I have a zip file of (what I assume) is the state of the VM when it was sent to me. I cannot unzip it as it is huge and simply requires more HD space than I have available but I did extract the vmx file and examine it. Other than the UUIDs and the fact that mine reads cleanShutdown = "FALSE" they are identical. The log contains the following lines Jun 23 10:11:18.080: vmx| SNAPSHOT: SnapshotConfigInfoRead: Unable to load dict from 'E:....\MachineName.vmsd'. Jun 23 10:11:18.080: vmx| SNAPSHOT: SnapshotConfigInfoRead failed for file 'E:....\MachineName.vmx': Dictionary problem (6) Jun 23 10:11:18.082: vmx| SNAPSHOT: Snapshot_TimeStampTiers failed: Dictionary problem (6)

    Read the article

  • How can I measure actual memory usage from my running processes?

    - by NullUser
    I have two servers, server1 and server2. Both of them are identical HP blades, running the exact same OS (RHEL 5.5). Here's the output of free for both of them: ### server1: total used free shared buffers cached Mem: 8017848 2746596 5271252 0 212772 1768800 -/+ buffers/cache: 765024 7252824 Swap: 14188536 0 14188536 ### server2: total used free shared buffers cached Mem: 8017848 4494836 3523012 0 212724 3136568 -/+ buffers/cache: 1145544 6872304 Swap: 14188536 0 14188536 If I understand correctly, server2 is using significantly more memory for disk I/O caching, which still counts as memory used. But both are running the same OS and if I remember correctly, I configured both with the same parameters when they were installed. I did a diff on /etc/sysctl.conf and they are identical. The problem is, I am collecting memory usage and other metrics over a period of time, (eg: vmstat, iostat, etc.) while a load is generated on the system. The memory used for caching is throwing off my calculations on the results. How can I measure actual memory usage from my running processes, rather than system usage? Is used - (buffers + cached) a valid way to measure this?

    Read the article

  • Nginx settings are screwing up my Drupal form submissions, how do I fix?

    - by bflora
    How do I tell Nginx to "ignore" specific URLS or pages on my web site? I run a Drupal site where anonymous visitors get served via NGINX while logged in users get served via Apache. We do this to keep the load down and scale better. It works great, except, since we set up nginx, a good number of Drupal forms no longer work. For example, before installing Nginx, if you created a new article, then clicked "edit" and edited the article. You could click "save" and your changes to the article would be saved. After setting up nginx, when you make edits and then click "save," the page simple refreshes, but now with "nginx-index.php" inserted into the URL. And your changes to the form were not actually saved to the database. So if you go to edit an article, you'll be on domain.com/node/##/edit or something like that. When you try to save your changes to the form, you'll wind up at domain.com/nginx-index.php?q=node/##/edit. And your changes will not be saved. There is a way around this, but only for administrative users. If you go to a form where this problem is happening, then comment or comment-out three lines in our settings.php file, the form will save properly. Those three lines are: // 'cache_form' = array( // 'engine' = 'db', // ), If they're commented, you uncomment them, them save the form. If they're uncommented, you comment them out and save the form. Obviously, this sucks. My friend who set up our server (and then left the country) told me that there are some Nginx settings that can tell it to "ignore" certain URLs or pages which could work here. How do I do this and where do I do it?

    Read the article

  • default domain and first domain in apache2 causing trouble

    - by acidzombie24
    I have 3 sites and a default/test site using mono's test page. I created aFirst, c, d, e, zLast. zLast has rewrite rules that should be evaluated last. Since the first VirtualHost seen is the default i set it to this --aFirst-- <VirtualHost *:80> ServerName www.domain.tld ServerAdmin webmaster@localhost DocumentRoot /var/www/test DirectoryIndex index.html index.aspx index.php MonoDocumentRootDir "/var/www/test" MonoServerPath rootsite "/usr/local/bin/mod-mono-server2" MonoApplications rootsite "/:/var/www/test" <Directory /var/www/test> MonoSetServerAlias rootsite SetHandler mono AddHandler mod_mono .aspx .ascx .asax .ashx .config .cs .asmx </Directory> </VirtualHost> The problem is my default page (the ip address of my server) and the first website (csite.ddomain.net) have problems (even though csite is defined in c and is not the first virtual host). The ip address of my server and csite.ddomain.net ALWAYS load the same site. Either monos test page or the csite. It flips every time i restart apache. Why isnt the server ip address always loading the default page (mono test page) and why isnt csite.ddomain.net always loading the site i want!?! Heres the config for --csite-- <VirtualHost *:80> ServerName csite.testdomain.net ServerAdmin webmaster@localhost ServerAlias s.csite.testdomain.net DocumentRoot /var/www/prjname DirectoryIndex index.html index.aspx MonoDocumentRootDir "/var/www/prjname" MonoServerPath rootsite "/usr/local/bin/mod-mono-server2" MonoApplications rootsite "/:/var/www/prjname" <Directory /var/www/prjname> MonoSetServerAlias rootsite SetHandler mono AddHandler mod_mono .aspx .ascx .asax .ashx .config .cs .asmx </Directory> </VirtualHost> aFirst, c, d, e, zLast are all enabled.

    Read the article

  • Reverse proxy for mailserver (SMTP + HTTP for web client)

    - by ba
    I'm looking at doing some reverse proxy work for a mail server with corresponding web client. Both servers are running on the same machine, this is not a server with a high load. :) The solution I've discussed with friends is having the mail server/web client on our internal network. Then to put a reverse proxy on the DMZ to service both SMTP and web client HTTP-traffic to the mail server on the internal network. From what I understand this is the recommended secure solution? So far I've thought for the SMTP-proxy part of using postfix which will receive mail, do some spamhause and similar anti-spam measures and if it all checks out, send the mail to the mail server on the inside. The mail server on the inside will send all outgoing mail to the proxy which will then send it out on the Internet. For the web client I'm not sure exactly which software I should be running on the proxy machine, I've been thinking about using Squid -- but that's basically based on the fact that I know squid is a http proxy. The web client data will be sent out over SSL. Reading around some here on Serverfault I've seen other people using Apache with mod_proxy+mod_security for similar situations. Am I thinking correctly for this solution? What software would you guys use and with which modules? Thanks in advance for the help! :)

    Read the article

  • 404 with serving static files in a custom nginx configuration

    - by code90
    In my nginx configuration, I have the following: location /admin/ { alias /usr/share/php/wtlib_4/apps/admin/; location ~* .*\.php$ { try_files $uri $uri/ @php_admin; } location ~* \.(js|css|png|jpg|jpeg|gif|ico|pdf|zip|rar|air)$ { expires 7d; access_log off; } } location ~ ^/admin/modules/([^/]+)(.*\.(html|js|json|css|png|jpg|jpeg|gif|ico|pdf|zip|rar|air))$ { alias /usr/share/php/wtlib_4/modules/$1/admin/$2; } location ~ ^/admin/modules/([^/]+)(.*)$ { try_files $uri @php_admin_modules; } location @php_admin { if ($fastcgi_script_name ~ /admin(/.*\.php)$) { set $valid_fastcgi_script_name $1; } fastcgi_pass $byr_pass; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /usr/share/php/wtlib_4/apps/admin$valid_fastcgi_script_name; fastcgi_param REDIRECT_STATUS 200; include /etc/nginx/fastcgi_params; } location @php_admin_modules { if ($fastcgi_script_name ~ /admin/modules/([^/]+)(.*)$) { set $byr_module $1; set $byr_rest $2; } fastcgi_pass $byr_pass; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /usr/share/php/wtlib_4/modules/$byr_module/admin$byr_rest; fastcgi_param REDIRECT_STATUS 200; include /etc/nginx/fastcgi_params; } Following is the requested url which ends up with "404": http://www.{domainname}.com/admin/modules/cms/styles/cms.css Following is the error log: [error] 19551#0: *28 open() "/usr/share/php/wtlib_4/apps/admin/modules/cms/styles/cms.css" failed (2: No such file or directory), client: xxx.xxx.xxx.xxx, server: {domainname}.com, request: "GET /admin/modules/cms/styles/cms.css HTTP/1.1", host: "www.{domainname}.com" Following urls works fine: http://www.{domainname}.com/admin/modules/store/?a=manage http://www.{domainname}.com/admin/modules/cms/?a=cms.load Can anyone see what the problem could be? Thanks. PS. I am trying to migrate existing sites from apache to nginx.

    Read the article

  • Optimizing Apache for large file serving

    - by D_Guy13
    I have a random problem with Apache that I can't quite figure out, here is my setup, Windows Server 2008 R2, 64 Bit, 5GB RAM, SSD with 200 MB(Read/write) and Dual Core CPU @ 2.1 GHz A dump from mod-staus, Server Version: Apache/2.4.7 (Win32) mod_limitipconn/0.24 mod_antiloris/0.5.2 PHP/5.5.9 Server MPM: WinNT Apache Lounge VC11 Server Built: Nov 21 2013 20:13:01 Current Time: Thursday, 21-Aug-2014 23:38:06 W. Europe Daylight Time Restart Time: Thursday, 21-Aug-2014 20:30:47 W. Europe Daylight Time Parent Server Config. Generation: 1 Parent Server MPM Generation: 1 Server uptime: 3 hours 7 minutes 18 seconds Server load: -1.00 -1.00 -1.00 Total accesses: 283025 - Total Traffic: 1172.2 GB 25.2 requests/sec - 106.8 MB/second - 4.2 MB/request 62 requests currently being processed, 388 idle workers Serving large .zip & iso files using mod_xsendfile. (File size range 500 MB - 1.5 GB) The setup works and is running fine. CPU usage is very unstable, jumps all the time between 10% - 90% and the servers goes down when it hits 100%. In that case I have to hard restart the server. Server it outputting traffic at 30 Mbps. Is there anything else I should think about to get a more stable CPU usage? Is that CPU usage normal? Can switching to Linux help me achieve better CPU usage?

    Read the article

  • G4 server running slow

    - by Abby Kach
    I have HP proliant ML 350 servers. We have 8 remote locations where users connect and log on to our server through DYNDNS to access our company ERP's to conduct day to day work. The base of our company ERP's is oracle for which we have a separate server.Now the problem is day by day the load on the server is increasing and the speed is getting slower and slower and users are facing a lot of issues . so I are planning to implement Sonic wall VPN. I conducted a demo of sonic wall but it was slower than the current speed of dyndns. the configuration of my server is as follows :- Linux HP ProLiant 370 Intel Xenon 3.20 GHZ 150 GB (72 * 2) 3 GB Suse Omega HP ProLiant 370 Intel Xenon 3.20 GHZ 300GB (72.8 * 4) Raid 5 4 GB Windows Server 2K3 Enterprise Edition Storage Box HP Storage Works 1400 Intel Xenon 2.00 GHZ 4 TB(1 TB * 4) Raid 5 2 GB Windows Server 2K8 Enterprise Edition Domain & Terminal HP ProLiant 350 Intel Xenon 3.20 GHZ 250 GB(72.8 * 3) Raid 5 4 GB Windows Server 2K3 Enterprise Edition Can some one help me as to how can i speed up my network at remote locations and reduce the problems of speed etc..

    Read the article

  • Apache Server with memcache, varnish and php slow request times

    - by coolestdude1
    My issue is that these servers are taking rather long for request about 2 seconds on average just to serve files. When we had just one server doing everything it was noticeably faster even with the same web app (Drupal 6 and Drupal 7). I want to get this number down to a reasonable level and so I need some help getting to the bottom of why the request times are so slow. This can cause the webapp to hang on post or put and generally leads to a bad user experience on my sites. PS: I am more of a server newbie so this has confounded me for quite some time. The domains: collabornation.net nptrainingworks.com (they run off the same two webservers using vhost configs) The Gear: Two Rackspace 4 Gig servers running CentOS 6.2 Final They have a mounted file system (gluster) that is used to keep files the same on both machines. They are behind a rackspace load balancer running round robin. Mysql is run using php-pdo and php-mysql as such mysql is run on another instance running memcache on that machine with phpMyAdmin located there as well. Apache version number 2.2.15-15.el6.centos.1 (httpd.x86_64) Varnish version number 3.0.2-1.el5 (varnish.x86_64) PHP version number 5.3.14-1.el6.remi (php.x86_64) Configs Linked Below Apache Conf Vhost Conf Varnish Backends Varnish Defaults Varnish Acl PHP INI Again need some help, much appreciated!

    Read the article

  • Safe use of Update-FormatData?

    - by Steve B
    In a custom PowerShell module, I have at the top of my module definition this code: Update-FormatData -AppendPath (Join-Path $psscriptroot "*.ps1xml") This is working fine as all .ps1xml files are loaded. However, the module is sometimes loaded using Import-Module MyModule -Force (actually, this is in the install script of the module). In this case, the call to Update-FormatData fails with this error : Update-FormatData : There were errors in loading the format data file: Microsoft.PowerShell, c:\pathto\myfile.Types.ext.ps1xml : File skipped because it was already present from "Microsoft.PowerShell". At line:1 char:18 + Update-FormatData <<<< -AppendPath "c:\pathto\myfile.Types.ext.ps1xml" + CategoryInfo : InvalidOperation: (:) [Update-FormatData], RuntimeException + FullyQualifiedErrorId : FormatXmlUpateException,Microsoft.PowerShell.Commands.UpdateFormatDataCommand Is there a way to safely call this command? I know I can call Update-FormatData with no parameters, and it will update any known .ps1xml file, but this would work only if the file has already been loaded. Can I list somewhere the loaded format data files? Here is a bit of background: I'm building a custom module that is installed using a script. The install script looks like : [CmdletBinding(SupportsShouldProcess=$true,ConfirmImpact="High")] param() process { $target = Join-Path $PSHOME "Modules\MyModule" if ($pscmdlet.ShouldProcess("$target","Deploying MyModule module")) { if(!(Test-Path $target)) { new-Item -ItemType Directory -Path $target | Out-Null } get-ChildItem -Path (Split-Path ((Get-Variable MyInvocation -Scope 0).Value).MyCommand.Path) | copy-Item -Destination $target -Force Write-Host -ForegroundColorWhite @" The module has been installed. You can import it using : Import-Module MyModule Or you can add it in your profile ($profile) "@ Write-Warning "To refresh any open PowerShell session, you should run ""Import-Module MyModule -Force"" to reload the module" Import-Module MyModule -Force Write-Warning "This session has been refreshed." } } MyModule defines, as first statement, this line : Update-FormatData -AppendPath (Join-Path $psscriptroot "*.ps1xml") As I updated my $profile to always load this module, the Update-Path command has been called when I run the install script. In the install script, I force import the module, which be fire again the module, and then, the Update-Path call

    Read the article

  • Win7 Hangs During App Install/Upgrade/Uninstall

    - by JadeMason
    I have a custom built PC that intermittently hangs when installing, uninstalling, or upgrading applications. Technical Specs ASUS P5E w/ WiFi Motherboard Intel Core2 Quad Q6600 Processor 4x 2GB G.Skill DDR2 800 SDRAM ASUS EAH2900XT / Radeon HD 2900XT 512MB Video Card Under normal operation the machine runs reliably, even under heavy load, such as video transcoding. The temperature never gets anywhere near where I would worry about it. However, the machine regularly hangs (complete lockup, no response to keyboard or mouse, no activity on-screen) when either installing a new application, uninstalling an existing application, or applying patches to existing applications or the OS. This is extremely frustrating as this machine is primarily used as a HTPC. Several apps are configured for automatic updates, and these updates sometimes cause the machine to lockup while we are watching content on the PC. In previously investigating this issue, I found one likely problem could be my Logitech Webcam. The Logitech software has a bug that leaves an entry in HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\ Control\SessionManager\PendingFileRenameOperations Which references the Temp directory. My registry contained this error, so I uninstalled the webcam software and deleted this registry key value. Unfortunately, the machine will still intermittently hang. I've noticed that the hangs always happen when an install/upgrade/uninstall requires elevated privileges (presumably to modify the registry). I can typically get at least one install/upgrade/uninstall to complete after a reboot, but after that it is a game of russian roulette to see if the operation will succeed or hang the machine. The event log is not helpful, as log messages end at the time of the hang, with no record of a warning or error. My only recourse when the machine hangs in this way is to perform a hard reset/power cycle. Any tips on how to further debug this issue are greatly appreciated.

    Read the article

  • Access is denied when running batch file on Windows7

    - by Radek
    I have a bat file on Windows7 that I used to run. Now I am not able to run it because of Access is denied error. My account is part of administrator group. C:\EduTester\others>mysqlbackup.bat Access is I am able to see the file via more mysqlbackup.bat when inside the directory where the file sits. C:\EduTester\others>more mysqlbackup.bat @echo off rem settings etc etch In fact I used to run the bat file as administrator using runas command runas /savecred /user:yogurt\administrator "c:\EduTester\others\mysqlbackup.bat" Attempting to start c:\EduTester\others\mysqlbackup.bat as user "yogurt\administrator" ... RUNAS ERROR: Unable to run - c:\EduTester\others\mysqlbackup.bat 2: The system cannot find the file It used to run ok few days ago. I am not aware that I would change something that could affect this. I have just tried to restart the Windows7 computer and I am experiencing the same. UPDATE In event viewer I can see this Windows cannot load the user's profile but has logged you on with the default profile for the system I think it might the be cause...

    Read the article

  • Coldfusion:-Firefox can't establish a connection to the server at localhost

    - by Fransis
    I installed Coldfusion 8 trial version on my system (XP Professional sp3). I created an Folder in the “C:/Coldfusion8/wwwroot” called “buildProject” containing an Index.cfm and some other .cfm files. But I am unable to access the Neither my project files or CFIDE/Administrator I tried the following URLS http://localhost:8500/wwwroot/buildProject/ http://localhost:8500/CFIDE/administrator/index.cfm http:// 127.0.0.1:8500/wwwroot/buildProject/ http:// 127.0.0.1:8500/CFIDE/administrator/index.cfm http://localhost /wwwroot/buildProject/index.cfm http://localhost /CFIDE/administrator/index.cfm http://localhost /wwwroot/buildProject/ http://localhost /CFIDE/administrator/index.cfm Firefox can't establish a connection to the server at 127.0.0.1:8500. The site could be temporarily unavailable or too busy. Try again in a few moments. If you are unable to load any pages, check your computer's network connection. If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web. • I cleared the browsing “History” from both IE and FF. • I have restarted the CF server in the Control Panel Administrative Tools Services • Even restarted the IIS Getting the same error. Further I was trying to access IE/FF via CFbuilder But still I am getting the error “The connection was refused when attempting to contact [URL].” My inetpub is in the D rive where as CF8 is in C drive Also when i check IIS-5 Control Panel Admin tools Services I do not find the Localhost under web sites or FTP sites. Kindly help me with a fix.

    Read the article

  • VPS goes slow at more than 20 users online at the same time

    - by hachiari
    I have 512 MB VPS (brustable to 1GB) Somehow, the site goes slow when there are about 10 users, and becomes impossible to load at 20 users online at the same time. I wonder what could be the problem for this. The bandwidth connection of the VPS is 1Gbps. Here is some settings in my VPS: KeepAlive Off <IfModule prefork.c> StartServers 7 MinSpareServers 7 MaxSpareServers 10 ServerLimit 64 MaxClients 64 MaxRequestsPerChild 0 </IfModule> my.cnf settings - calculated Max Memory 300MB Output from UNIXBENCH INDEX VALUES TEST BASELINE RESULT INDEX Dhrystone 2 using register variables 376783.7 13429727.4 356.4 Double-Precision Whetstone 83.1 1137.5 136.9 Execl Throughput 188.3 1637.4 87.0 File Copy 1024 bufsize 2000 maxblocks 2672.0 148868.0 557.1 File Copy 256 bufsize 500 maxblocks 1077.0 79430.0 737.5 File Read 4096 bufsize 8000 maxblocks 15382.0 1410009.0 916.7 Pipe Throughput 111814.6 4419722.0 395.3 Pipe-based Context Switching 15448.6 561505.1 363.5 Process Creation 569.3 10272.7 180.4 Shell Scripts (8 concurrent) 44.8 514.3 114.8 System Call Overhead 114433.5 3537373.8 309.1 ========= FINAL SCORE 295.0 I am afraid that the VPS company limit the number of connection to the VPS... is it possible? The server is in Japan, but the site has global traffic (some of the traffic are from countries with low speed connection). Could this be the problem? This is a serious problem :( my site just cant grow if this keeps on happening... please tell me if you have any idea. Thank You, Bryant

    Read the article

  • Why is my server performance degrading to the point of stopping, periodically?

    - by Pascal Aschwanden
    So, once in a while, I see in firebug that a request takes over 15 or even 60 seconds to respond and sometimes never. Here is what I've ruled out: It's not the CPU, cuz every time I check the Server load its less then 6 for all 3 numbers It's not the memory, because thats fairly low too, less the 50% It's not the I/O anymore, because I've seen the graphs that Joyent sent back to me when I requested them, and they show less then 3MB of I/O (mostly all read). It's not the SQL performance - I've profiled every last SQL command that runs, and they're all (99.9% of them anyway) running in less then 30ms, most run in less then 5ms. Oh and I've been profiling all the script execution times, and even the when the problem occurs, the script always manages to finish in 50ms or less (that's 1 / 20th of a second ). Now, I do run alot of ajax calls. 1 every 2 seconds per user and I have 300 DAU+. But, even if all 300 are playing simultaneously, thats still only 150 calls per second max. The only other thing I can think of is that one of my neighbors is funky. The problem is highly intermittent. 99% of the time it works perfectly and there's excellent performance. but 99%+ is not good enough. Eventually the performance gets so bad I have to restart the server, at which point everything is fine again. I've done this about 4 times now. Any ideas? Note: this is on joyent, vps, intro package 256mb of ram with bursting. here are the mysql dump info: Traffic ø per hour Received 18 MiB 29 MiB Sent 134 MiB 221 MiB Total 151 MiB 251 MiB Connections ø per hour % max. concurrent connections 5 --- --- Failed attempts 0 0.00 0.00% Aborted 0 0.00 0.00% Total 9,418 15.59 k 100.00%

    Read the article

  • Large scale file replication with an option to "unsubscribe" from a replicated file on a given machine

    - by Alexander Gladysh
    I have a 100+ GB files per day incoming on one machine. (File size is arbitrary and can be adjusted as needed.) I have several other machines that do some work on these files. I need to reliably deliver each incoming file to the worker machines. A worker machine should be able to free its HDD from a file once it is done working with it. It is preferable that a file would be uploaded to the worker only once and then processed in place, and then deleted, without copying somewhere else — to minimize already high HDD load. (Worker itself requires quite a bit of bandwidth.) Please advise a solution that is not based on Java. None of existing replication solutions that I've seen can do the "free HDD from the file once processed" stuff — but maybe I'm missing something... A preferable solution should work with files (from the POV of our business logic code), not require the business logic to connect to some queue or other. (Internally the solution may use whatever technology it needs to — except Java.)

    Read the article

  • How to extract attachments from Exchange 2003 database

    - by John
    I have an ancient Exchange 2003 server that I'm getting ready to retire. All user accounts have been migrated to Google Apps for Business, so no new mail is being sent or received on the server. There are less than 50 accounts on the server, but some are very large so that the whole Exchange database is between 10 and 20 GB. The largest account has over 100,000 messages. I believe that in the migration to Gmail, some attachments were not migrated. For peace of mind, I'd like to get the attachments out of the Exchange database. The only way I know of to do this is to set up a 2nd computer with Outlook on it, set up one of the accounts, and then sync the whole mail history and get the attachments out that way. Is there something simpler that I can do? Here are two possibilities: An Exchange attachment retrieval tool/script that pulls attachments for all accounts directly out of the Exchange database. An Exchange PST exporter tool/script that will export PST files for all accounts so that I can just load the PST files into Outlook at will.

    Read the article

  • HAProxy, health checking multiple servers with different host names

    - by Marco Bettiolo
    I need to load balance between multiple running servers with different host names. I cannot set-up the same virtual host on each one. Is it possible to have only one listen configuration with multiple server and make the Health Checks apply the http-send-name-header Host directive? I am using HAProxy 1.5. I came up with this working haproxy.cfg, as you can see, I had to set a different hostname for each health check as the health check ignores the http-send-name-header Host. I would have preferred to use variables or other methods and keep things more concise. global log 127.0.0.1 local0 notice maxconn 2000 user haproxy group haproxy defaults log global mode http option httplog option dontlognull retries 3 option redispatch timeout connect 5000 timeout client 10000 timeout server 10000 stats enable stats uri /haproxy?stats stats refresh 5s balance roundrobin option httpclose listen inbound :80 option httpchk HEAD / HTTP/1.1\r\n server instance1 127.0.0.101 check inter 3000 fall 1 rise 1 server instance2 127.0.0.102 check inter 3000 fall 1 rise 1 listen instance1 127.0.0.101:80 option forwardfor http-send-name-header Host option httpchk HEAD / HTTP/1.1\r\nHost:\ www.example.com server www.example.com www.example.com:80 check inter 5000 fall 3 rise 2 listen instance2 127.0.0.102:80 option forwardfor http-send-name-header Host option httpchk HEAD / HTTP/1.1\r\nHost:\ www.bing.com server www.bing.com www.bing.com:80 check inter 5000 fall 3 rise 2

    Read the article

  • VPS Memory Exchausted Even With Light Settings

    - by user101570
    Linux noob here. I have a 256MB VPS on Ubuntu 11.04 server and when I run "free -m" the result shows all memory being used (including the second line re: buffers/cache). I found this very strange, considering I only have 5 Apache processes running each chewing up about 20MB each. MYSQL is taking up 30MB. To my knowledge, and according to "top", I have no other memory hogs operating. Settings that may be relevant: PHP memory_limit = 32M MYSQL key_buffer = 16M Prefork MPM Maxclients = 10 So when I reviewed these settings, I naturally thought maxclients was too high, so I tried switching it to 5. Now not only does my memory still show as being 100% used, my website loads much, much slower, despite not getting any traffic aside from mine at the moment. I don't understand this. I thought a single Apache process handles all requests from a client received within the "KeepAliveTimeout" window, which I've set to 2 seconds. With my initial config. of 10 maxclients, my page load times are around .3ms, so a single process should handle that no problem, correct? So next I went to an extreme level of 1 for maxclients. My memory is still at 100% usage and my site loads painfully slow. I'm a noob at a complete loss here. According to the many tutorials I've read on basic server setup, I should be good to go. Help! Please! Edit: total used free shared buffers cached Mem: 256 256 0 0 0 0 -/+ buffers/cache: 256 0 Swap: 0 0 0

    Read the article

  • What Device/System to use as a "router on a stick"

    - by Jeff Leyser
    I need to create several distinct VLANs, and provide a way for traffic to move between them. A "router on a stick" approach seems ideal: Internet | Router with Trunking Capability ("router on a stick") * * Trunk between router and switch * Switch with Trunking Capability | | | | | | | | | | | LAN 2 | LAN 4 | | 10.0.2.0/24 | 10.0.4.0/24 | | | | LAN 1 LAN 3 LAN 5 10.0.1.0/24 10.0.3.0/24 10.0.5.0/24 We have trunk-capable Layer-2 switches. The question is what to use as the router on a stick. My choices seem to be: 1) Use an existing Cisco 5505 ASA firewall. It appears the ASA can do the routing, but it's a 100Mbps device, and so seems sub-optimal at best 2) Buy a router. This seems overkill. 3) Buy a Layer-3 switch. Also seems overkill. 4) Use an existing Linux Box as a router 5) Use a new Linux box as a router' 6) Something I'm not thinking of I think either (4) or (5) is my best option, but I'm not sure how to choose between them. I expect the amount of traffic that has to cross the VLANs to be somewhat small, but bursty. How much load does routing add to a CentOS machine?

    Read the article

  • Using Truecrypt to secure mySQL database, any pitfalls?

    - by Saul
    The objective is to secure my database data from server theft, i.e. the server is at a business office location with normal premises lock and burglar alarm, but because the data is personal healthcare data I want to ensure that if the server was stolen the data would be unavailable as encrypted. I'm exploring installing mySQL on a mounted Truecrypt encrypted volume. It all works fine, and when I power off, or just cruelly pull the plug the encrypted drive disappears. This seems a load easier than encrypting data to the database, and I understand that if there is a security hole in the web app , or a user gets physical access to a plugged in server the data is compromised, but as a sanity check , is there any good reason not to do this? @James I'm thinking in a theft scenario, its not going to be powered down nicely and so is likely to crash any DB transactions running. But then if someone steals the server I'm going to need to rely on my off site backup anyway. @tomjedrz, its kind of all sensitive, individual personal and address details linked to medical referrals/records. Would be as bad in our field as losing credit card data, but means that almost everything in the database would need encryption... so figured better to run the whole DB in an encrypted partition. If encrypt data in the tables there's got to be a key somewhere on the server I'm presuming, which seems more of a risk if the box walks. At the moment the app is configured to drop a dump of data (weekly full and then deltas only hourly using rdiff) into a directory also on the Truecrypt disk. I have an off site box running WS_FTP Pro scheduled to connect by FTPs and synch down the backup, again into a Truecrypt mounted partition.

    Read the article

< Previous Page | 607 608 609 610 611 612 613 614 615 616 617 618  | Next Page >