Search Results

Search found 21356 results on 855 pages for 'check digit'.

Page 655/855 | < Previous Page | 651 652 653 654 655 656 657 658 659 660 661 662  | Next Page >

• Replaced CPU and black screen but no beep?

  - by luke

  I'm having a bit of trouble with a GIGABYTE GA-MA78G-DS3H (rev. 2.0) motherboard. Recently when trying to clean my AMD Phenom II X 4 CPU, I dropped it and broke some pins. I have now brought a Athlon 64 X2 5400+. However, it does not seem to work. To begin with, I cleared the CMOS via the jumper located near the battery. This was because I had my AMD Phenom II overclocked and did not wish for the same voltage to go to the new CPU. I then tried booting with the monitor plugged into the chipsets VGA but no luck. No signal was sent to the monitor, and the monitor just went into standby. I then tried it off the graphics card but the same happened again. Then I tried to check whether the CPU could executed some BIOS codes by stripping the RAM out and making sure a speaker was plugged in but no beeps could be heard. I replaced the speaker and tried again but no luck. The CPU is brand-new so what is going wrong?

  Read the article

• JBoss database connection pool configuration

  - by Qben

  I am facing an connection pool issue in my clustered JBoss installation. From time to time one of my connection pools will hit the roof and I get a lot of these in my logfile. java.sql.SQLException: No ManagedConnections available within configured blocking timeout ( 30000 [ms] ); The odd thing is that I can see in the JMX console that the ConnectionCount hit the roof, but at the same time InUseConnectionCount is often quite small. The problem will resolve itself after a couple of minutes but during recovery phase my application will not work (for obvious reasons). The question is if this indicate an error in the configured timeouts of the connections (I pretty much use defaults), or if my pool is simply too small to handle the peaks. Under normal operation I would say I use ~40% of the configured max number of connections. The reason I just don't increase the max number of connection is that if I actually used up all connections I suspect that InUseConnectionCount would hit the roof. Hence I suspect I might have more issues than just a too small pool size. Maybe InUseConnectionCount has decreased at the time I check jmx-console and it actually do hit the roof? I tend to collect data every second minute. Any hints are more than welcome.

  Read the article

• Multi-partition USB stick

  - by nightcracker

  In my freelance job as "the dude that fixes your computer" I have an extremely handy tool, a bootable USB stick with Ubuntu LiveCD that allows me to recover and investigate in a known, working environment. Now, I want to reformat this USB stick and reinstall with Casper-RW persistance. I did this a few times before with a FAT-formatted USB stick. It was a horror. The USB drive corrupted constantly, by people accidently removing the USB stick, the computer not properly shutting down, ETC. Now what I want to create a multi-partition USB stick so I can put Ubuntu on a ext partition, but still be able to store some Windows stuff in it, by having a secondary FAT partition. However I read somewhere that Windows will only check the first partition on USB sticks, giving a problem with the first bootable linux partition. Is this possible on some way? EDIT Perhaps it wasn't clear what the problem is. The problem is that I read somewhere that Windows will only recognize the first partition on a USB stick. But I want two partitions, a ext partition and a FAT partition. No issues so far, but in order to be bootable the ext partition must be the first one!

  Read the article

• How do I set up postfix to store e-mail in a file instead of relaying it?

  - by GomoX

  I want to run a staging copy of a production server on a local environment. The system runs a PHP application, which sends e-mail to customers in various scenarios and I want to make sure no e-mail is ever sent from the staging environment. I can tweak the code so it uses a dummy e-mail sender, but i'd like to run the exact same code as the production environment. I can use a different MTA (Postfix is just what we use in production), but I'd like something that is easy to set up under Debian/Ubuntu :) So, I'd like to set up the local Postfix install to store all e-mail in (one or more) files instead of relaying it. Actually, I don't really care how it's stored as long as it's feasible to check the e-mail that was sent. Even a set up option that tells postfix to keep the e-mail in the mail queue would work (I can purge the queue when I reload the staging server with a copy from production). I know this is possible, I just haven't found any good solution online for what seems like a fairly common need. Thanks!

  Read the article

• Symlink path can be followed manually, but `cd` returns Permission denied

  - by Ricket

  I am trying to access the directory /usr/software/test/agnostic. There are several symlinks involved in this path. As you can see by the below transcript, I am unable to cd directly to the path, but I can check each step of the way and cd to the symlinked directories until I reach the destination. Why is this? (and how do I fix it?) Ubuntu 12.10, bash > ls /usr/software/test/agnostic ls: cannot access /usr/software/test/agnostic: Permission denied > cd /usr/software/test > cd agnostic bash: cd: agnostic: Permission denied > pwd -P /x/eng/localtest/arch/x86_64-redhat-rhel5 > ls -al | grep agnostic lrwxrwxrwx 1 root root 15 Oct 23 2007 agnostic -> noarch/agnostic > ls -al | grep noarch ... lrwxrwxrwx 1 root root 23 Oct 23 2007 noarch -> /x/eng/localtest/noarch > cd noarch > cd agnostic bash: cd: agnostic: Permission denied > ls -al | grep agnostic lrwxrwxrwx 1 5808 dip 4 Oct 5 2010 agnostic -> main > cd main > ls (correct output of `ls`) > pwd /usr/software/test/noarch/main > pwd -P /x/eng/localtest/noarch/main

  Read the article

• Should I buy more RAM for my computer or a better CPU?

  - by Reijer The Coder

  I have recently bought a new laptop, an ASUS N56VJ-S4149H. I bought it to use it in all possible ways I could want, so that would be gaming downloading and streaming movies browsing the web and programming software. So far it has been running great but one thing annoys me a little bit. I frequently play Mount&Blade: Warband, it's a great game and you should check it out. Everything runs smoothly but only when I turn down the 'Texture Detail'. Otherwise it will lag a lot and I can't really play. Now my question is: Is this a problem of not enough RAM? At first I was really sure it was but after thinking about for a while I'm not anymore. My computer only has 4 Gigabytes of RAM and there is still a slot open. So will it improve when I buy another 8 Gigabytes? EDIT: It has an Nvidia GeForce GT 635M inside. and an Intel Core i5 3230M CPU with 2,6 GHz. Help and answers are really appreciated. Thanks to all.

  Read the article

• Uploading to another domain gives HTTP code 405

  - by dragon112

  I'm trying to upload a file (which can be quite large) from the website of one server to the backend of another server using plupload. Lets say: domain 1 = http://www.websitedomain.com/uploadform domain 2 = http://www.backenddomain.com/uploadhandler Trying to upload i send the following: OPTIONS /main/uploadnetwork.php HTTP/1.1 Host: backenddomain.com Connection: keep-alive Access-Control-Request-Method: POST Origin: http://www.websitedomain.com User-Agent: Mozilla/5.0 (Windows NT 6.1; WOW64) AppleWebKit/537.4 (KHTML, like Gecko) Chrome/22.0.1229.79 Safari/537.4 Access-Control-Request-Headers: origin, content-type Accept: */* Referer: http://www.websitedomain.com/uploadform Accept-Encoding: gzip,deflate,sdch Accept-Language: nl-NL,nl;q=0.8,en-US;q=0.6,en;q=0.4 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 DNT: 1 But when I try to start the upload the server returns the following: HTTP/1.1 405 Method Not Allowed Allow: GET, HEAD, OPTIONS, TRACE Content-Type: text/html Server: Microsoft-IIS/7.5 X-Powered-By: ASP.NET X-Powered-By-Plesk: PleskWin Date: Mon, 01 Oct 2012 12:41:57 GMT Content-Length: 999 After doing some research I found out that a browser does this to check if the server will accept the intended message. It looks like my server doesn't feel like accepting a simple POST call even tho i use post all the time. The Google Chrome console gives the following error: XMLHttpRequest cannot load http://www.backenddomain.com/uploadhandler. Origin http://www.websitedomain.com is not allowed by Access-Control-Allow-Origin. Does anyone know how to stop the browser from checking or how i can tell my server to just accept the POST?

  Read the article

• apache access and error log written in same file

  - by user196075

  i have issue that access and error log are written in same file ! , the configuration in virtualhosts.conf as the following : <VirtualHost *:80> ServerName ************ ServerAdmin support@************8 DocumentRoot /var/www/html/*********.com ErrorLog /var/log/httpd/********/********.com_error_log CustomLog /var/log/httpd/********/********.com_access_log combined <Directory /var/www/html/***********.com> Options -Indexes FollowSymLinks AllowOverride All </Directory> </VirtualHost> as you see from the configuration each access and error logs should be save separately , but both logs are written in *.com_access_log , i have double check all permission , group and owner ... can't find anything wrong previous error in log file : [Thu Sep 19 14:15:02 2013] [error] [client 192.168.10.54] client denied by server configuration: /var/www/html/**********/show_has_offers.php i have tried to generate same error , i can find the hit in access log only as the following : 192.168.10.75 - - [24/Oct/2013:08:11:14 +0000] "GET /show_has_offers.php HTTP/1.1" 404 1586 "-" "Mozilla/5.0 (X11; Linux x86_64; rv:22.0) Gecko/20100101 Firefox/22.0" 0 17332 and nothing in error log !! Please advice ...

  Read the article

• Windows Server 2008 R2 creating a multi-year client certificate using the IIS certsrv page while deploying SSTP VPN

  - by Warren P

  I am trying to follow instructions on Technet about deploying a Standard (non-enterprise) SSTP based VPN) that were originally written for Server 2008, but I am using Server 2008 R2, I have gotten as far as the part where it asks you to create a request a Server Authentication certificate. I have deployed IIS, and Active Directory Certificate Services, and chose "Standalone" and "Standard" (non-enterprise) Certificate Authority because I don't have an OID and don't think I should have to get one for a simple deployment of SSTP. The resulting certificates made by the Certification Authority "Issue" command, only have a 1 year period of validity, I want a multi-year certificate. At no point in this process is there any way to input this information unless it's through the Attributes text input area on the Advance Certificate Request page, which appears to be generated using an old ActiveX control, which means I can only do this using the workarounds in the article that I linked at the top, and only using Internet Explorer. Update:: It may be that this question is pointless since self-signed keys do not appear to work, when I try them, using Windows 8 as the VPN client. The problem is that the keys that are self-created by the technique shown here do not have any Certificate Revocation Server URLs and so you get an error "The revocation function was unable to check revocation", and the VPN connection fails.

  Read the article

• What other ways can I load balance EC2 servers without using Elastic Load Balancing?

  - by undefined

  I have a web application that consists of a web server managed by a web hosting firm, a set of EC2 instances in amazons cloud and a MySQL database (hosted on the webserver). MySQL is behind a firewall and is set to allow access from Localhost and from a single IP address which is an Amazon Elastic IP address that is attached to the EC2 instance I have been running up to now. The problem is that I want to look at my scaling up and load balancing strategy for my EC2 instance. To this end I have been investigating the Elastic Load Balancers and Autoscaling tools that Amazon provides and have managed to set this up fine but for one thing - connecting to the MySQL database running on my webserver. I realised (thanks to answers on Serverfault) that I needed to check firewall settings and add the IP address for the load balancer, however Elastic Load Balancers provide you with a DNS name, not an IP address and infact the IP addresses change over time so this will not work. I have been told by the company hosting the database that the way the firewall works is to look up the IP address of the DNS name and store the IP rather than the DNS name. so basically this will not work and the only way to allow access would be to open up the SQL port to allow access from anyone! Is this a viable idea? Should I look at moving my database into the cloud? Is there another firewall that the server company can use? Should I find another way of load balancing (if so what?) tricky one eh? any help appreciated!

  Read the article

• Computer will not boot - disk read error - cannot boot from HD or DVD

  - by Grant Palin

  This is a 3 year-old system: HP a1640n. There have been no issues with it in the past. I added a video card 2 years ago, and more memory 1 year ago, both without issues. There haven't been any recent hardware changes. I did install Win7 in Oct., but there were no issues with that either. I used the computer fine two nights ago, and turned it off. Yesterday, I tried to turn it on, and got the error: "A Disk Read Error Occurred. Press CTRL ALT DEL to restart" So I restart, see the initial start screen (HP) and enter the BIOS. The hard drive and dvd drive appear to be listed, but the names are gibberish text. I tried putting a Windows disk in the dvd drive, and continued with the boot, but the disk did not get recognized. Even though the BIOS was set to check for optical media before the hard drive. Back to the error screen. If the computer would boot from a cd or dvd, I would just figure the hard drive needed replacing. But both being problematic worries me. Is this a matter of replacing both the hard drive and dvd drive, or might it be an indication of a bigger problem? Thanks for any advice.

  Read the article

• lighttpd domains and url matching

  - by Manuel

  I'm trying to configure lighttpd so that: www.domain1.org/admin uses config1 any other URL on www.domain1.org uses config2 any url on www.domain2.org uses config2 So basically, domain1 and domain2 should use the same configuration except for when domain1 is accessed via an URL that starts with /admin I tried so far a number of variations, including this one: $HTTP["host"] =~ "domain1.org" { $HTTP["url"] =~ "^/admin" { // config1 alias.url = ("/media/admin" => "/usr/share...", "/static" => "/var/www/...") url.rewrite-once = ( "^(/media/admin.*)$" => "$1", "^(/static.*)$" => "$1", "^/favicon\.ico$" => "/media/favicon.ico", "^(/.*)$" => "/application.fcgi$1", ) server.document-root="/var/www/application" fastcgi.debug = 1 fastcgi.server = ( "/application.fcgi" => ( "main" => ( "socket" => "/var/www/application/application.sock", "check-local" => "disable", ) ), ) } else $HTTP["url"] !~ "^/admin" { // config2 } $HTTP["host"] !~ "domain1.org" { // config2 } But no matter what, accessing domain1.org/admin yields a 404. Is there anything that I am missing?

  Read the article

• Calculating memory footprints using /proc/sysvipc/shm

  - by MarkTeehan

  This is for a SLES 10 database server. One of my servers runs three databases and three app servers; I am analyzing how their shared memory segments grow and shrink to avoid intermittent out-of-memory scenarios. "Top" is hot helpful for this since its calculations for RES and VIRT are inconsistent. I am doing this by matching up the contents of /proc/sysvipc/shm with memory usage reported by the database admin console. I do this by totaling up saving the contents of /proc/sysvipc/shm and then total up "bytes" for all of the segments for the offending userid. This is a large server with hundreds of segments and tens (or hundreds) of GB of allocated memory per userid. However it doesn't match up - the database management software claims to be using around 25% more memory than the total I calculate. Negligible swap space is in use, so I am ignoring that. I am running it as root so I am sure I see all shared memory segments. My question is : is all (significant) allocated memory recorded in /proc/sysvipc/shm, or is this only shared memory (*and not "un-shared" memory?). If this is incorrect, what is the correct way to calculate out the total allocated memory for each userid? Also: I believe doing a 'cat' on this file locks server IPC. I check it every 5 seconds - is it likely that this frequency could be problematic? Thanks! Mark Teehan Singapore

  Read the article

• Laptop CPU fan not working properly

  - by Smith

  My laptop's CPU fan is suddenly acting very bizarre, and I am at a loss for what to do so I am asking for some help. Specifically, the fan is not even starting to spin until the CPU reaches 60 degrees Celsius (checked through HWmonitor). Once it is on, however, it properly stays on even when the CPU gets back to idle temps around 38 Celsius. Before, the fan was simply starting with the computer and staying on like normal. I've checked this for consistency both by allowing cold boots to ramp up temperature to 60 Celsius (the slow climb also causing the laptop to become unreasonably warm near the heatsink), and also running Prime95 immediately to kickstart the fan (this works every time). The fan seems to be stationary when turning the computer on from either sleep or shutdown. The fan will start at POST very briefly, and then stop completely. I've checked the BIOS for a SmartFan setting but haven't found any. I've opened the case to check for dust or debris and have not found anything (I applied some canned air to the area just in case). The laptop is a Lenovo ThinkPad Edge E430 and the CPU is an Intel Core i5 3210m @ 2.5 GHz. Any advice would really be appreciated.

  Read the article

• My laptop screen keeps dimming

  - by Rowland

  I have a Cryo laptop with Windows 7 installed, bought in December 2011. Sometimes the screen seems to persistently dim and/or brighten up, even as I am doing things. In fact the brightness is varying even as I type this. The battery is always fully charged and connected to the mains. I have checked many times the battery/power-saving settings always leaving the settings the same way; full brightness and never dimming when on the mains. Yet when the screen starts playing up I can end up with the screen dimming and brightening almost continuously. I once went to the "adjust screen brightness" window when the screen had dimmed. I found the brightness slider on 100% (as I expected) but, as I dragged it to the left, to dim the screen, it first brightened and then started dimming, i.e. the screen setting said 100% brightness but it was only at, maybe 80%. I have checked with Cryo and they just say check the power settings. I know what these are and how to work them and always set them to never dim/full brightness, yet still my laptop starts this dimming every so often.

  Read the article

• Ping not working

  - by Nishant

  Ping is not working to and from this IP to my computer. inet addr:10.125.104.4 Bcast:10.125.111.255 Mask:255.255.240.0 My computer is like this Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 10.125.65.75 Subnet Mask . . . . . . . . . . . : 255.255.252.0 Default Gateway . . . . . . . . . : 10.125.64.6 We both CAN reach the common gateway IP , 10.125.96.6 . What should I check ? What is the barrier in sending info if we both have a common gateway that is pingable ? Besides I can login to a intermediate server and ssh to this server also !!

  Read the article

• mysqldump --where with = operator doesn't get all rows = - Help!

  - by JonathanLIVE

  I have a situation with a particular table that now thinks it contains 4 Petabytes of data. I know that sounds cool, but I assure you, it is only on a 60GB partition. This table has 9 fields in it. One of them is a domain_id field. It is the best field to identify the rows by, as there are only approximately 6300 of them. The only other field option to match has over 2million records, and thats just more difficult. I cannot do a straight mysqldump because it will attempt to output all 4PB of data and fill the drive long before it gets close to that, so I need to surgically remove the good stuff, destroy the db, and recreate it. I believe if I can do a dump for each domain_id record, then I will get most of the usable data out of it. This is what I am trying to use: mysqldump -u root --skip-opt -q --no-create-info --skip-add-drop-table --max_allowed_packet=1000000000 database table --where="domain_id=10" domains10.sql Using this I expect every row with the domain_id 10 to be exported. However, when I check the export, I am only getting 1 row, when however I look at the db, there are many many rows. It is as though the operator just finds one, then gives up. I have tried various operators. Using the < or I am able to get more of the data, but the export stops short at certain rows where the data has been compromised. With over 6000 to go through, I can't narrow down which rows are being affected in the export easily enough. So, what I need is an operator that will basically do what I thought = would do, simply give me an export of all records that match the specific field. Also note, the only way I got this DB even accessible is through an innodb force recovery 3. So I need to get this right, because after this is done, I have to drop the db in order to make mysql functional again. Looking forward to any helpful answers.

  Read the article

• Hardware testing tool/suite

  - by Aviator

  Hi All, I just bought a new core i5 system (assembled) and started installing Windows 7. It was failing for many times and at some point got installed. After that, frequent crashes related to MEMORY. So checked the RAM using memtest86+ and found many errors.I got it replaced with the vendor and now if i install ANY OS, at some point in installation it either freezes completely with no response for hours, or restarts automatically. I tried installing Windows 7, Windows Vista and Ubuntu 9.10. I tested the new RAM again and found no problems in about 2 passes using memtest86+. I even updated the BIOS using bootable USB and even the problem persists. I am really not sure which hardware is causing trouble. I dont have any OS inside it, so i have to check using bootable CDs DVDs and USB only. Please advice on how to proceed. Are there any suites/ separate tools for checking integrity of each hardware parts and troubleshoot it? I wanted to confirm which part is problematic before going for replacement. Thanks a lot! This is the config: Core i5, MSI P55-GD65, GSKill 2x2GB, Seagate 500GB 7200rpm, CM Extreme 600W PSU, Saphhire Radeon 5770 1GB, LG DVD Writer

  Read the article

• How to slave a 3.5" 500gb SATA external hard drive (Western Digital) to my Dell Inspiron laptop

  - by AJ HDD

  I have a 3.5" Western Digital My Book 500gb external hard drive. I gave it to a friend of mine, and he broke the USB port in it. I went to a nearby comp repair shop and had him solder the thing, and it didn't detect when it when I plugged it into my Dell Inspiron laptop. I recently saw about the 3.5" SATA to USB enclosure, so I went to check it. Strangely, when its placed in the enclosure, its not detecting in Windows. Also, when it was put as secondary (I'm guessing slave) to the shop fellow's desktop, it shows up in the BIOS and while starting, but then again doesn't show in Windows 7. The guy told me that I need to use a data recovery tool to get my data back. P.S. Whe WD hard drive doesnt have an OS, just data. So my question is: Can I slave the drive to my Dell laptop and try to recover the data, and if so how? I would really appreciate it any help, thanks in advance.

  Read the article

• Unable to install drivers of any kind of device on windows 8.1

  - by saadj55

  Windows 8.1 is unable to install drivers. First, I wanted to install Android ADB drivers for my Chinese Android Phone. I downloaded the relevant drivers from the manufacturers site and enabled USB debugging on my phone and tried to install it but Windows failed to find any drivers in the driver folder. After searching on google, I got to know that I will have to edit the win_usb.inf file in order to install the drivers so I did the editing part also. Added these line: %SingleAdbInterface% = USB_Install, USB\VID_0BB4&PID_0C03 %CompositeAdbInterface% = USB_Install, USB\VID_0BB4&PID_0C03 to both NTamd and NTx86 sections but the problem persists. Phone's current hardware id is: VID_0BB4&PID_0C03 I noticed that I need hardware ID with &MI_01 appended at the end. But Windows detects the device with the above hardware ID. I have the webcam drivers so I uninstalled WebCam Drivers to check if they can be installed back but I am also not able to install drivers for it. Windows is detecting the camera without that &MI_01 part. Please help. I cannot install webcam nor my android phone.

  Read the article

• what are these weird IP address connections in resource monitor?

  - by bill

  I decided to check out Resource Monitor (on the 'Performance' tab in Task Manager, Windows 7) and I noticed in the "Network" section that the 'System' image name kept making a bunch (~5 at a time) of connections to random IP addresses, it would show anywhere from 1-500 bytes/sec 'sent'. They would stay connected for 1-2 minutes. -All web browsers are closed So, first thing I did was run a trace from network-tools.com on some of these IP addresses. 8/10 were outside of US and did not resolve to any host name. Of the 10 IP addresses I traced, 2 were in US, 4 showed origins in China, and one each to Algeria, Russia, Pakistan, Korea. (!) So, the next thing I did was turn off my wireless card, watch the connections disappear, then turn the card back on, and within 30 seconds more random connections were created by System, with different IP addresses from the first time. The next thing I did was go open Task Manager, Show Processes From All Users, then I killed just about everything that wasn't (what appeared to be) a windows process. Turned on wi-fi, and again within 30 seconds, random IP addresses connect for ~ 1 min at a time, new ones coming and going. I occasionally use bit torrent on this machine, but there was definitely no process that seemed related to bt running after I went through task manager, and bt wasn't open to begin with. So, any ideas on what these connections might be for? I have been using Ad-Aware Free and AVG Free on this computer for a while now, always up to date..

  Read the article

• Why does windows (file) explorer try to connect to port 80 (http) instead just using smb?

  - by Erik

  Background: On an almost freshly installed pc I get a message along the lines of : "windows cannot find some-file-server-name. Check the spelling and try again"... when trying to access any fileshare. Troubleshooting so far: pinging works. Both by ip and by name the almost identical pc next to this one can access the file server everyone else can access the file server the pc in question can not access other open fileshares but it can connect to the internet And now for what I think is the interesting part: running wireshark with ip.addr == local.ip.add.ress and ip.addr == server.ip.add.ress tells me that it tries to connect over http. the server replies but after a few messages back and forth it stops the other machine of course just uses smb I guess port 80 just means it defaults to webdav, but I haven't been able to find anything that can cause this. Googling it the closest thing I found was this http://www.techrepublic.com/article/get-vista-and-samba-to-work/6353849 but then again this was an XP pc and I wasn't able to connect to other native Windows shares (and I tried the solution anyway and it didn't work.)

  Read the article

• UNC shared path not accessible though necessary permissions are set

  - by Vysakh

  I have 2 environments A and B. A is an original environment whereas B is a clone of A, exactly except AD servers. AD server of B has been assigned a trust relationship with A, so that all the service and user accounts of A can be used in B too. And trusting works fine, perfect!! But I encounter some issues accessing UNC paths(\server2\shared) with these service accounts. I had a check in A environment and all the permissions set in that environment is done in B too (already set since it is a clone of A),but the issue is with B environment only. And FYI, the user is an owner of that folder in both the environments. I tried creating a folder inside the share(\server2\shared) using command prompt, but failed with error "access denied". What I done a workaround is that I added that user in "security" tab of folder permissions and after that it worked fine. But this was not done in the original environment. Is this something related to trust relationship? Why the share to the same location for the same user works differently in 2 environments, though they've been set with the same permissions. FYI, these are windows 2003 servers. Can someone please help.

  Read the article

• Mysql Query - That Is Returning Blatanty Incorrect Result

  - by user866190

  I am building a VPS node that is running Ubuntu 10.10LTS, Apache2, Mysql 5.1 and php5. I could not log in to my website admin through the browser, even though I am using the correct login details. So I logged in from the command line to check the results. When I run this query I get expected results: mysql> select * from users; +----+----------+-----------------------+----------+ | id | username | email | password | +----+----------+-----------------------+----------+ | 1 | myUserName | [email protected] | myPassword | +----+----------+-----------------------+----------+ And the same goes for this query: mysql> select * from users where id = 1; +----+----------+-----------------------+----------+ | id | username | email | password | +----+----------+-----------------------+----------+ | 1 | myUserName | [email protected] | myPassword | +----+----------+-----------------------+----------+ 1 row in set (0.00 sec) But when I run this query I get this 'unexpected response': mysql> select * from users where username = 'myUserName' and password = 'myPassword'; Empty set (0.00 sec) I am not sure why this is happening. Any help would be greatly appreciated. BTW.. I will be encrypting the user details but for now I just want to get it set up. Please help, Thanks

  Read the article

• Varnish going sick

  - by junke1990

  I'm having trouble with Varnish, it works for a couple of views and then just goes sick... The weird thing is that it does work for about 20 or 30 requests. If I call apache directly it works fine. I'm running Varnish Version: 3.0.3-1 on Debian Squeeze and, for now, Apache on port 80 and Varnish on port 8080 on the same server.. I'm using https://github.com/mattiasgeniar/varnish-3.0-configuration-templates as base for my VCLs and modified the VCLs to support Concrete5. Anyone any clue on how I should debug this? backend default { .host = "127.0.0.1"; .port = "80"; .connect_timeout = 1.5s; .first_byte_timeout = 45s; .between_bytes_timeout = 30s; .probe = { .url = "/"; .timeout = 1s; .interval = 10s; .window = 10; .threshold = 8; } } LOG 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1353791312 1.0 0 CLI - Rd ping 0 CLI - Wr 200 19 PONG 1353791315 1.0 0 Backend_health - default Still sick 4--X-R- 0 8 10 0.000689 0.000000 HTTP/1.1 301 Moved Permanently (the 301 is because I check for www.)

  Read the article

< Previous Page | 651 652 653 654 655 656 657 658 659 660 661 662  | Next Page >