Search Results

Search found 24516 results on 981 pages for 'visual c 2008'.

Page 671/981 | < Previous Page | 667 668 669 670 671 672 673 674 675 676 677 678  | Next Page >

• IPSec on Domain Controllers and Trusted Domains

  - by OneLogicalMyth

  I am looking at configuring IPSec as follows: Isolation Request authentication for inbound and outbound connections Computer and user (Kerberos V5) I am looking to do a blanket deployment across all servers and domain controllers. Workstations I will leave as not set. What impact in terms of the domain controllers with the 2-way forest trust do think I would see? Should I exclude the IP addresses of the trusted domain controllers? I don't want to stop communication between the current and trusted forest, however I do want IPsec to be used within the current forest on all servers. The trusted forest is running 2008 R2 and the current forest is 2012 R2.

  Read the article

• How to install a "virtual" network card on a virtual server?

  - by vikp

  Hi, We have purchased an unmanaged VPS windows hosting solution from one of the UK based companies. We have Windows Server 2008 Standard Edition. We need to install certain third party applications on that server. Unfortunatelly, one of the applications requires a MAC address to be present at all times - this is their way of making sure that software is not pirated (which it isn't). We have tried installing a virtual loopback network card, but this has brought the server down - i.e. we couldn't connect using remote desktop any longer. At the moment we are limited with what we can try. This is an unmanaged solution, therefore any support including restarts is rather costly. Are you aware of any low-risk solutions? Thank you

  Read the article

• Ways to do simple failover with one server and two IPs

  - by CrassHoppr

  The setup is one server (Windows 2008) at one location with two incoming connections. As the server has to interface with various on-site devices, and will have a small number of incoming connections, a data center is not an option, and instead cable/dsl connections must be used. The goal is that users visit https://service.site.com and are sent to either the primary IP address or a secondary IP if the primary is down. I've seen advice to use round robin DNS for this, but caching an IP for a downed interface is something I'd like to avoid. Is something like this possible with these constraints?

  Read the article

• Backing up Windows 2003 Server that has Certificate Authority

  - by Dina

  I want to export and migrate a Certificate Authority CA role from a Windows 2003 machine to a new copy of Windows 2008 R2 virtual machine. I was told that I cannot have 2 CA roles on the same network at the same time. Therefore, I must first export the certificates on the older machine, delete the CA role, then add the CA role on the new machine and import the certificates into it. As a safety precaution, I am tasked to find a backup solution in case this does not work and I need to revert back to the old Windows 2003 CA. My question is: What is the best software for doing this type of backup? I am currently trying out Symantec Backup Exec 2012. Which I hope will allow me to create a backup prior to removing CA role on Windows 2003. If this CA migration fails, the backup will allow me to revert the old machine to a time before I removed its CA role.

  Read the article

• Multiple Reporting Services databases in one instance?

  - by Tedd Hansen

  Is it possible to have multiple Reporting Services databases in one MSSQL instance? I have a MSSQL 2008 R2 with RS set to SharePoint Integrated Mode. This RS is in use and can't be changed. I do however need a RS in native mode for the TFS installation to be able to use it. Am I required to set up a new instance of MSSQL? Bonus question: If so, is that permitted under the MS licensing scheme or is it an additional cost?

  Read the article

• How to remove Excel List Manager?

  - by jdmuys

  I have a spreadsheet with columns set as using the List Manager. I want to remove the list manager. However, the "Remove List Manager" item in the "List" menu of the List toolbar is always disabled. I tried selecting a number of different set of cells in the list, to no avail. "Remove List Manager" stays stubbornly disabled (grayed out). What am I missing? I am using Excel 2008 version 12.1.5.

  Read the article

• MSSQL: Choice of service accounts

  - by Troels Arvin

  When installing MS SQL Server 2008, one needs to associate a service account with the installation (possibly even several accounts, one for the SQL Server Agent, one for Analysis Services, ..., but let's leave that for the case of simplicity). The service account may be local account, or a Windows domain account. If a domain account is used: Can MSSQL start, if connectivity to the domain controllers is temporarily down? If the answer is yes: Should each DBMS instance on each server have a separate account, or does it make sense to use a particular "MSSQL" domain account on all MSSQL-installations in the organization? If separate accounts are used for each instance on each server: Does it make sense to create a special MSSQL security group in the domain and place all the MSSQL service accounts in that group, perhaps to ease replication, etc? Is there a common, generally accepted naming convention for MSSQL service account(s)?

  Read the article

• When send a meeting invite to a specific user, you get a undeliverable response back from another us

  - by jherlitz

  We have a user, where it doesn't matter who sends it, but if you send her a meeting invite through outlook (exchange 2007), you get a non-deliverable message back from another user. Same one all the time though. I checked her shared calendar properties and removed the user from the list. I checked and made sure she wasn't using cache mode. I checked the manage full permissions and send permissions within exchange and the user is not listed. What am I missing? Notes: Using Outlook 2007 with Exchange 2007 on a XP box and Server 2008.

  Read the article

• Virtual MS Sql Server not consuming enough CPU

  - by rocketman

  We have a Win2008 server 32 bit running as a virtual machine under ESX server. It has 6 CPU cores of 2Gz each and 4GB ram. It's running MS Sql Server 2008 R2 only. Problem: The server is heavily loaded and responds slowly. From windows taskmanagers point of view, it really looks overloaded, CPU wise. However, our external "cloud manager" says it's only using 2.5GHz worth of CPU-cycles in the cluster. I/O times looks "good". We have already tried to set the SQL servers number of working threads from 0(auto) to 256, to no effect. How to tune the VM host, guest or SQL to use all of it's alotted resources? Does it sound possible att all?

  Read the article

• How to access a site in IIS with no DNS mapping

  - by CiccioMiami

  In my IIS 7.5 hosted in a Windows Server 2008 R2 I have several websites with no DNS address assigned. Let's take for instance the site (as named in IIS) with site name mySite. I have for this site the standard binding with no host name. Suppose that my server IP address is, for instance, 101.22.23.01. Therefore it seems logic to me that in order to access the website, I should place in the address bar of my browser: [IP_address]/[sitename] in this case: 101.22.23.01/mySite but it does not work. Shall I specify something else in the bindings?

  Read the article

• php crashes when I try to add extensions

  - by Christy

  Hi all, I am trying to install phpmyadmin on my web server with Windows 2008 and iis 7. PHP is running fine and I have several sites that rely on it. When installing phpmyadmin - it has errors at the bottom that crypt and mbstring are not properly installed. When I try to add the php_mcrypt.dll and/or the php_mbstring.dll to the php.ini file (I verified the location and the right file through phpinfo) it crashes. I get a 500 error on all the websites, and I get an error on the server saying FastCGI has failed. Does anyone know how to fix this or why it is happening? Shouldn't I be able to add extenstions? I have the dll files in the extension folder, which is referenced in the php.ini and other extensions (installed previously) are working as expected. Other info: php version 5.2.8, pdo driver for mysql version 5.0.51a Thanks in advance!

  Read the article

• Wordpress Installation on Two Servers - Loadbalancing

  - by rihatum

  Hi All, I have to install wordpress (One Blog, one domain, for e.g. mycompany.com/blog) on two servers sharing one database on a different server, these two servers are behind a loadbalancer and the db would be on another server. We are planning this way due to high traffic. I have done standalone wordpress installations on a single server, on windows 2003, 2008 with IIS6, 7 etc I am just researching as to how would I implement this. What would be the steps to achieve this and upon searching I saw some posts regarding the wp-content/uploads directory to be synced at regular intervals ? your help much appreciated Thanks for reading

  Read the article

• Backups of Exchange 2007 SP3 using VSS are abnormally large

  - by Stew

  I have recently implemented Veeam backup and recovery 6.0, and have noted when backing up my exchange server via incremental updates, it is transferring way more data than expected. Backup is incremental, and setup to use VSS. VSS is stable and healthy, according to vssadmin. Exchange 2007 SP3 running on Windows Server 2008 R2, just last weekend I installed the latest Rollup for Exchange. I thought the nightly incrementals were large, but perhaps my users really are sending that much mail so I tested taking one incremental backup, waiting 10 minutes and taking a second. The second incremental backup transfered 5.8GB of data. We as an organization are absolutely NOT putting 5.8GB of data on the mail server every 10 minutes. Are there any other veeam users who have seen something similar? Is my test faulted? Are there other considerations for VSS?

  Read the article

• Want 2 external monitors with a 13' MacBook - is this possible?

  - by kevinburke

  I've got a 13' white MacBook from 2008 and I'd like to run one or two external monitors, my budget is $500. I've tried to do research and this is what I was going to get - will these work OK? Two Diamond BVU195 HD USB Display Adapters (DVI and VGA with included DVI to VGA adapter) to plug into the USB port Two Dell ST2310 monitors One external USB hub so I don't use up both of my USB ports Will this work? I've read some people say it does and some people say it doesn't, but I don't know enough to say either way. Also do you have recommendations for a better monitor than the dell sd2310? what's the best setup I can buy for $500? Thanks very much for your help, Kevin

  Read the article

• Removing information about deleted volume

  - by Pravin

  In order to increase space in my c drive, I had to delete all my volumes and create again allocating more space to C which I did, after which my drive name G didn't exist. Before this I used to install all my softwares in G. Now since the drive does not exist, I want to remove all info about the softwares I installed in G as they got deleted when volume got deleted. I also want to install cilk++ but it gives me an error-invalid drive g:. If I insert pendrives so I get a volume named G, cilk++ installer runs but says that it will be integrated to visual studio 2008 which i previously had in G drive(but no longer exists) and doesn't show visual studio 2010 which i recently installed in C drive. How do I fix this? Please help.

  Read the article

• Excel: Look up function for combinations of cells in a single column

  - by Rebecca

  I'm looking to find the number of times a certain combination of values appears in a single column, I was hoping to do this in Excel but I'm starting to think it may not be possible. As an example, I have a list that looks like a longer vertical version of this: F1 F3 F2 F4 F1 F3 F4 F1 F3 F4 F1 F3 F4 And I want to know how many times a specific order (say F1 F3 F4) occurs, in this example 3 times (in my case the lookup sequences are 8 cells long). Is there a way to run over the whole column and identify the instances where this combination of cells occurs? I'm running Excel 2008 for Mac. Many thanks!

  Read the article

• Dummy SMTP server as a service

  - by levidos

  Hello, I have a Windows Server 2008 machine with IIS installed which is hosting a webapp that is sending some notification mails once-in-a-while. What I'd like to do is to monitor the email sent by the application. For this I need a dummy SMTP server which intercepts messages but won't send them further but save them locally on the hard disk.I've already found some of them like Papercut, SMTP4Dev. The problem with these that I have to be logged on the server all the time which is not suitable because the server has only 2+1 TS connections. I like to run a program like these as a windows service and check the mails when I need them. Any suggestion is much appreciated. Best Regards,Levente Rog

  Read the article

• Shared volume for data (multiple MDF) and another shared volume for logs (multiple LDF)

  - by hagensoft

  I have 3 instances of SQL Server 2008, each on different machines with multiple databases on each instance. I have 2 separate LUNS on my SAN for MDF and LDF files. The NDX and TempDB files run on the local drive on each machine. Is it O.K. for the 3 instances to share a same volume for the data files and another volume for the log files? I don't have thin provisioning on the SAN so I would like to not constaint disk space creating multiple volumes because I was adviced that I should create a volume (drive letter) for each instance, if not for each database. I am aware that I should split my logs and data files at least. No instance would share the actual database files, just the space on drive. Any help is appretiated.

  Read the article

• MacBook repeatedly disconnects from Wi-Fi

  - by redwall_hp

  I have an early 2008-model MacBook (2.4 GHz). The Wi-Fi router I have at home is a Linksys WRT54GX2 that I have had for a few years. My MacBook has recently started disconnecting from the router every few minutes, which is rather annoying. I can reconnect again without having to restart the router or anything, as it seems that the MacBook is just dropping the connection. I have tried changing the channel on the router, and upgrading the laptop from Leopard to Snow Leopard made no difference either. I'm only about six feet from the Linksys device, so distance isn't an issue. This only happens with the Linksys router, while I can use the local library's open network without any issues. The problem also seemingly becomes more pronounced after midnight. What could the problem be? Edit: Here are the logs that Spiff requested: http://pastie.org/951761

  Read the article

• Missing Jumbo and MTU for Broadcom NIC?

  - by Mike

  I have two Broadcom BCM5708C NetXtreme II GigE NICs in my Dell Windows SBS 2008 server. I would like make one them them Jumbo Frames enabled so that I can add it to my SAN whose VLAN on the switch is already using 9000 MTU. Broadcom's own data sheet for this NIC claims that it is Jumbo Frame capable up to a 9000 MTU. The problem is that there is no setting for Jumbo or MTU in the NIC's configurable settings. There are other settings but just not the one I need to change. Am I missing something here? The driver claims to be up-to-date when I allow Windows to search on-line.

  Read the article

• Symfony sfControlPanel 500 error only when executing 'tasks'

  - by rrlange

  As a bit of background, I recently had to restore a Symfony site from backup. Ever since the 'successful' restore, I am running into an exception when trying to execute a(ny) task via the web-based sfControlPanel: Unable to find PHP executable stack trace * at sfToolkit::getPhpCli() in SF_ROOT_DIR/plugins/sfControlPanelPlugin/modules/sfControlPanel/actions/actions.class.php line 93 FYI: symfony version 1.0.6 PHP 5.2.6 (cli) (built: May 2 2008 16:06:40) Apache/2.2.3 CentOS 5.* Thank you very much for any and all suggestions as to what might be amiss. Addendum: I neglected to mention that I can the frontend app (and certain backend apps) perfectly fine via the web. I am also able to run common tasks via the command line (cc etc.).

  Read the article

• Getting VPN to work from Virtual PC

  - by strobaek

  Setup: Host is running Windows7. Virtual PC is a Windows Server 2008 running under VMWare workstation 6.5. From the Host I have a VPN to e.g. TFS and other resources. From the VPC I need to connect to e.g. a SQL server via the VPN. My problem is, that I cannot get a connection from the VPC. If I'm sitting on the corporate network, all is working fine (but then I don't have the VPN). From home - where the VPN is required - it does not work. I have two network adapters defined/configued. One as BRIDGED and one as Host Only. IF I change the one being BRIDTED to NATS I have no connectivity at all from the VPC. I have no problems connecting from my host to the VPC. Thanks.

  Read the article

• Cannot connect to IIS 7 from localhost

  - by Wout

  I cannot connect to the local IIS 7 using "http://localhost" in IE. "http://127.0.0.1" doesn't work either. The strange thing is that if I add a binding on e.g. port 81, then I can reach "http://localhost:81". Also turning off the firewall on the local machine doesn't help. The site is reachable from the internet. The local requests don't seem to hit IIS (no entries in the IIS log files). IIS is hosted on Windows Server 2008 R2 from behind a hardware firewall device. Note that I'm a programmer, not a network administrator, so I'm having a hard time trouble shooting this.

  Read the article

• team foundation server 2010 installation from DVD - I get agent installation instead!

  - by Avi

  GRRRRRRRRRRRR!(#Y%)@#!! They bragged they now have a very easy installation! I don't get it. I entered the MSDN "Disk 5000: Developer Tools" DVD, opened default.htm, clicked on the "Visual Studio Team Foundation Server 2010" link. The VSTFS2010 folder open. I click autorun.exe. And then I get "Microsoft Visual Studio Agents 2010 Setup". I don't get it. Why "agents"? I wanted to instal a server!

  Read the article

• Project Server 2010 site creation - the database connection string is not available

  - by Brandon Montgomery

  I am trying to get Project Server 2010 up and running on a Win Server 2008 box. I've got Sharepoint 2010 installed and Project Server 2010 installed. I open SharePoint Central Administration, then I go to Manage Service Applications Project Server Service Application. It looks like there is a site under the "Sharepoint - 80" section, but the Status says "Failed - see the Application event Log". When I click on the site and select "Retry" I get the same thing. In the event viewer, I see an error with SharePoint Foundation Search as the Source - it reads: Could not create a database session. Context: Application '276504a6-93b1-4c1f-a900-fd6ed9d5c117' Details: The database connection string is not available. (0xc0041228) How can I fix this? Is there some configuration I missed?

  Read the article

< Previous Page | 667 668 669 670 671 672 673 674 675 676 677 678  | Next Page >