Search Results

Search found 28559 results on 1143 pages for 'upgrade issue'.

Page 906/1143 | < Previous Page | 902 903 904 905 906 907 908 909 910 911 912 913  | Next Page >

• No sound out of headphone port on laptop

  - by Thanatos

  I cannot get sound out of the headphone port on a laptop. Headphones are plugged in, and sound comes out of the internal speakers. Windows behaves normally (sound switches to headphones when headphones are inserted). It did work in Linux at one point, but something changed, we're just not sure what. Rebooting doesn't fix. This appears to occur whether or not PulseAudio is running. Things I've tried: Rebooting. No effect. Booting into Windows. It works properly, so probably not a hardware issue. All of alsamixer. My only controls are this: "Master" Volume bar & mutable, unmuted. Controls volume. "PCM" Volume bar only. 100%. "S/PDIF" Mutable only, currently muted, has no effect. "S/PDIF" Default PCM", Mutable only, currently unmuted, has no effect. Killing PulseAudio. No effect. (It also won't stay dead! Something appears to be restarting it, and I can't tell what, but it is annoying as fuck.) alsactl init 0, no effect. sudo rm -f /var/lib/alsa/asound.state, no effect. General system info: Ubuntu 10.04 LTS Toshiba Satellite T135D-S1324 lspci says I have: 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller Some edits: Yes, the headphones are in all the way. This works in Windows: You plug headphones in, the internal speakers stop making noise, and noise comes out the head phones. Windows says I only have two sound cards: the HDMI port (which I don't care about) and the "sound card", which it claims is a "Conexant Pebble High Definition SmartAudio" In Windows, both the internal speakers and the headphone jack show up as one soundcard, which in my experience, is typical. (This is a laptop)

  Read the article

• ATI firepro will not detect a second DVI-D monitor

  - by John

  OK so weird issue here. I have previously been running 6 screens off of 3 of the older ATI firepro graphics cards but they had a problem with the heat sink getting too hot and warping the PCB resulting in total failure of the card, to replace my three dead cards I purchased a new-type ATI firepro with the newer heat sink design. I'm only using one at the moment to make sure they've fixed the problem before I waste more money on 2 more cards but this is where things start to get weird. The Firepro's only have one port on them, they connect to two monitors via a splitter cable going from the one port to two DVI connectors for the screens. When I plug two identical monitors in via their DVI inputs not matter what I do windows and Catalyst will only detect one screen. However if I use the VGA input on one of the screens with a VGA - DVI adaptor to plug it in to the card it works fine. This confuses me greatly. I'm currently using the ATI Firepro 2270 Graphics card with identical DELL U2311H screens. I can post the rest of the system spec as well if needed but I wouldn't have thought it would make much difference as it had no problem handling 6 screens before the graphics cards failed. Naturally both catalyst and ATI drivers are the most current version. ATI tech support has been absolutely zero help, they seemed to get stumped as soon as I verified that both screens were plugged in and connected properly. Anyone have any ideas?

  Read the article

• Poor performance on IIS7, only on Windows Server 2008, fine on Windows 7?

  - by user32005

  Hi, I'm new to IIS7 but have experience with other versions. I've been working on an application that works great in a dev environment (as always) but when I push it to a windows server 2008/IIS7 box performance takes a noticeable hit. The dev environment is Windows7/IIS7. The configuration in IIS is the same on the dev box as the server. I've tried all sorts of things to try and find a reason for this but I cant come to any conclusion. I've ruled out database problems on the live box as all data is cached after the first request. I've confirmed this to be true and made sure there is no additional database traffic. I've ruled out network issues with a combination of monitoring requests with fiddler and local debugging on the server. Whenever the code runs on the server there seems to be a performance issue. The server: Intel Core 2 Quad CPU Q6600 @ 2.40ghz with 2gb RAM. I know this is not fantastic but I was expecting it to at least perform as well as my dev environment (which is running much more on a lower spec). The CPU using peaks at under 60%, and memory usage is less than half of the available. I've enabled failed request tracing and most of the time is spent in a custom HttpModule, this module works to handle every request, I cant get any more detail as to what within the module may be causing the problem. Any ideas, I've been pulling my hair out for days now. Thanks

  Read the article

• Virtualize SBS 2003 - P2V vs migrating to new VM

  - by jlehtinen

  I need to virtualize a SBS 2003 server in my work environment. I need some tips on what people think is the best way to proceed. Background: The SBS 2003 server is the primary DC for the domain and also hosts FTP, RRAS(VPN), DNS, and file shares. Exchange is NOT used, neither is SQL server. DHCP is done via a firewall appliance. I have added a Server 2003 VM to the domain and promoted it to the DC role. AD/DNS is replicating here correctly. This was mainly done to provide fault-tolerance to the domain, I was not intending to make this VM the primary DC. I've already asked about buying upgraded licensing for Server 2008/2012 but was refused due to cost. Options: I see (at least) two routes I could take to complete this. From what I've read option 2 is the "preferred" method, but there's a few steps where I'm not clear on what to expect. Option 1.) P2V the primary DC Power off primary DC Power off secondary DC (to prevent USN rollback in case P2V has issue) P2V (cold clone) primary DC Boot new PDC VM Allow new hardware to detect Remove old NIC hardware from device manager Assign old IPs to new virtual NICs Reboot PDC VM, confirm connectivity and no major issues Power on secondary DC, confirm replication Option 2.) Create new VM, transfer roles, remove original DC from domain Create new VM, install SBS 2003 Do I need the original SBS install discs for this? MS migration doc mentions this. Add VM to domain, promote to DC role Does this start 7 day timer where two SBS servers can be in same domain? Set up RRAS on new VM Set up IIS/FTP on new VM Move file shares to new VM Transfer FSMO roles to new VM DC dcpromo original primary DC out of domain

  Read the article

• Nginx configuration leads to endless redirect loop

  - by brianthecoder

  So I've looked at every sample configuration I could find and yet every time I try and view a page that requires ssl, I end up in an redirect loop. I'm running nginx/0.8.53 and passenger 3.0.2. Here's the ssl config server { listen 443 default ssl; server_name <redacted>.com www.<redacted>.com; root /home/app/<redacted>/public; passenger_enabled on; rails_env production; ssl_certificate /home/app/ssl/<redacted>.com.pem; ssl_certificate_key /home/app/ssl/<redacted>.key; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X_FORWARDED_PROTO https; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_set_header X-Url-Scheme $scheme; proxy_redirect off; proxy_max_temp_file_size 0; location /blog { rewrite ^/blog(/.*)?$ http://blog.<redacted>.com/$1 permanent; } location ~* \.(js|css|jpg|jpeg|gif|png)$ { if (-f $request_filename) { expires max; break; } } error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } } Here's the non-ssl config server { listen 80; server_name <redacted>.com www.<redacted>.com; root /home/app/<redacted>/public; passenger_enabled on; rails_env production; location /blog { rewrite ^/blog(/.*)?$ http://blog.<redacted>.com/$1 permanent; } location ~* \.(js|css|jpg|jpeg|gif|png)$ { if (-f $request_filename) { expires max; break; } } error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } } Let me know if there's any additional info I can give to help diagnose the issue.

  Read the article

• 550 Requested action not taken: mailbox unavailable on OS X server 10.6

  - by Marc Graham

  I recently added a new domain to my mail server. I have 1 main server mail.example.com and several others that have the mx record pointing to mail.example.com. My two new domains have the mx record set correctly. The issue I am experiencing is the 550 Requested action not taken: mailbox unavailable error but only when I send emails to accounts on the new urls from an external email account such as gmail. If i send an email to one of the newly made email addresses with the new url from an email account within the same server it delivers normally. For example.... sending [email protected] to [email protected] receives 550 error sending [email protected] to [email protected] works normal here is a report from wormly.com with server and account names changed for obvious reasons Resolving hostname... Connecting... SMTP -> FROM SERVER: 220 existingmailserver.com ESMTP Service ready SMTP -> FROM SERVER: 250-Requested mail action okay, completed 250-SIZE 0 250-AUTH LOGIN PLAIN CRAM-MD5 250-ETRN 250-8BITMIME 250 OK MAIL FROM: [email protected] SMTP -> FROM SERVER: 250 Requested mail action okay, completed RCPT TO: [email protected] SMTP -> FROM SERVER: 550 Requested action not taken: mailbox unavailable SMTP -> ERROR: RCPT not accepted from server: 550 Requested action not taken: mailbox unavailable Message sending failed.

  Read the article

• Sudden problems with iptables not running

  - by Fourjays

  I've got a sudden issue with iptables not running on my CentOS 5.8/DirectAdmin XenVPS. All I have done today is install PHP APC and run an update (although I admittedly didn't pay much attention today - I usually do). Iptables has been running fairly smoothly since I installed it over 6 months ago. Basically when I try to run iptables -L it tells me: iptables v1.3.5: can't initialize iptables table `filter': iptables who? (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. I've looked around and tried a few things and it appears that maybe my kernel doesn't have the modules loaded? I've been reading this and tried the two commands they suggest to no avail. Except there does appear to be a mismatch on one bit of output: -bash-3.2# cd /lib/modules -bash-3.2# ls 2.6.18-194.32.1.el5xen 2.6.18-238.5.1.el5xen 2.6.18-274.7.1.el5xen 2.6.39.1-cs-domU 2.6.18-238.12.1.el5xen 2.6.18-238.9.1.el5xen 2.6.37.2-cs-domU 3.0.1-cs-domU -bash-3.2# depmod -a WARNING: Couldn't open directory /lib/modules/2.6.18-274.18.1.el5xen: No such file or directory FATAL: Could not open /lib/modules/2.6.18-274.18.1.el5xen/modules.dep.temp for writing: No such file or directory Does this mean the versions are out of sync? If so, what are my next steps to getting this fixed? As you can probably tell I am still learning how to manage my server so please be very clear in all advice. Many thanks :)

  Read the article

• ssh-add insists on passphrase

  - by Sam Walton

  I have a new ssh key problem. I have successfully used them for years with Heroku, Git and other servers so I can login without having to issue a passphrase. A few weeks ago, I was unable to push a git repository on my machine to my Heroku and it responded with Permission denied (publickey). Hmm. Everything else but this Heroku function still works. So I ssh-keygen -t rsa -C "newHeroku" with no passphrase (hit return so it would be empty). So I enter: sudo chmod 600 ~/.ssh/newHeroku* Then: ssh-add ~/.ssh/newHeroku.pub Returning return for the passphrase asked it exits without error. The next step is to: ssh-add /Users/sam/.ssh/newHeroku.pub To verify that it's "live" I enter: ssh-add -l To which the output is still The agent has no identities. Okay, to eliminate variables, I repeat the key generation process but entering in a passphrase for a new key. I ssh-add the new key and get the "Enter passphrase" as expected. Now this is why I'm posting here and not on a Heroku blog because ssh-add fails because the passphrase I used keeps getting rejected. It appears, even though I have no problem with my keys elsewhere, that something is wrong with passphrase because even though I get no errors, I get errors when on the one that expects a passphrase. One question, should I expect the Passphrase request for ssh-add when I have not generated a passphrase? It's been suggested that this is a clue and I offer it. Or maybe I have a poor understanding of what ssh-add is doing. Wouldn't be the first time I asked a stupid Q. Also, I'm on Lion and have updated no system updates in the few weeks of this period except application updates.

  Read the article

• I can't get my PC to start up by a normal way.

  - by ssice

  I couldn't write a more accurate title. I am just unable to start the computer by pressing the Power On button. I checked the Power Supply and it seems to give good voltage values in every pin. And this is not a BIOS malfunction because of bad overclocking or anything that may come to your mind. And I will tell you why. It happens that EPS (or any ATX-based) power supply has the ability to be powered-on by the Motherboard by jumping the 13th pin of the 24-pin-ATX-connector to COM/GND. I did it, after pushing the power on button (without any visual response) and, pwhaa! The machine turned on. I was able to read (and even write, if I wanted) BIOS values and then start any OS installed. Machine starts, so it's not any kind of misconfiguration. It seems some hardware related. I am able to power the machine on only if I already pushed the power on button. Though pushing it without jumping the 13th pin to ground for a second does not power the machine. Of course, jumping the pin without pushing the power on button does not tell the motherboard anything, so the computer would not start up either. It's as if the logic that connects the power button with the 13th pin derivation to GND was unable to be activated. What can be the issue? How can I solve it? My configuration is as follows: CPU: AMD Phenom 9850 X4 Black Edition MB: ASUS Formula II AM2 RAM: 2x2GB Corsair Dominator 5-5-5-15 2T @ 1066MHz DDR2 Tested also with only 1 module GPU: 2x XFX nVIDIA GeForce 9600 GT XxX Alpha Dog Edition @ Core: 540Mhz [SLi] Power Supply: Xilence 700W (ATX 12V 2.3 / EPS 12V 2.92 compatible) PS: I know the machine is like 2 years old. I hardly use it now, but my parents do.

  Read the article

• Driver denied access to PCI card

  - by Corin

  Alright, I asked this on StackOverflow (here) and they suggested trying ServerFault to get help on permissions. So here's the deal. We designed a custom PCI card and wrote the driver for it. It's been working for years without problems but now we encountered one particular installation were it doesn't work. The problem is that we cannot connect to the PCI to begin communication with it. We tried replacing the card and had the same problem. We had the motherboard replaced thinking the PCI slots were bad. That didn't help either. We tried the cards in a different computer and they all worked. So it seemed to be something specific to the computer. The Windows Device Manager indicates the device is working properly and seems to have all the correct driver info. We now have this troublesome computer back at the office for testing. With the help of some extra debug info in the driver we determined that we cannot connect because access is denied. Sounds like a permissions issue to me. I should note that we are logged into the system as a local administrator. So what configuration option in Windows can prevent access to a device?

  Read the article

• CloudFront with Custom Origin and ELB

  - by kmfk

  We are using CloudFront for our static assets but also wanted to allow for Gzip. We set up a new distribution with a custom origin pointing back to our application servers which are behind a elastic load balancer. We manually keep the files in sync across the cluster and update them when we publish. However, with this set up, we get nothing but Miss and RefreshHits from CloudFront, which so far has defeated the purpose. Is there any additional settings in order to use an ELB as your custom origin? In the docs, it references this as a viable solution. It appears when we point the distribution to a single server in our production cluster, cloudfront properly caches our assets. Is it possible that the sticky sessions cookie and the subsequent header that gets added by it could be an issue? Cache-Control: no-cache="set-cookie" //Added by load balancer Any ideas? FYI - currently, we have our custom origin pointing to a single EC2 instance, so caching is working correctly - in case you try to curl the file below. Example headers: curl -I http://static.quick-cdn.com/css/9850999.css HTTP/1.0 200 OK Accept-Ranges: bytes Cache-Control: max-age=3700 Cache-Control: no-cache="set-cookie" Content-Length: 23038 Content-Type: text/css Date: Thu, 12 Apr 2012 23:03:52 GMT Last-Modified: Thu, 12 Apr 2012 23:00:14 GMT Server: Apache/2.2.17 (Ubuntu) Vary: Accept-Encoding X-Cache: RefreshHit from cloudfront X-Amz-Cf-Id: K_q7Zy3_jdzlEJ85ukELVtdx1GmuXqApAbZZ7G0fPt0mxRMqPKX5pQ==,RzJmPku-rEIO9WlvuSoKa8hiAaR3dLk5KC4cQMWWrf_MDhmjWe8n6A== Via: 1.0 28c34f9fbf559a21ee16594849e4fc9c.cloudfront.net (CloudFront) Connection: close

  Read the article

• Windows 7 scheduled task returns 0x2

  - by demmith

  I have identical scheduled tasks running in Windows XP Pro and Windows 7. The XP Pro one runs fine, the Windows 7 one always returns 0x2 (which means, "The system cannot find the file specified"; however, executing from the command line is no problem) in the Last Run Result column of the Task Scheduler UI. The scheduled task executes a .bat file daily. The .bat file contains a call to execute a Perl script. As I stated in the previous paragraph, it executes under XP without any trouble but under Windows 7, no dice. The task under Windows 7 is set to "run whether the user is logged on or not." In this case it is me, I am the only user of the system. It is also set to "Run with highest privileges." And it is not hidden. The .bat file executes perfectly well from the command line - it calls the Perl script as expected and the Perl script does its thing. I have searched far and wide looking for an appropriate answer to this issue. So far I have found nothing. What the devil is going on with this Win7 scheduled task? I am ready to pull my hair out.

  Read the article

• Missing drive space in Server 2003

  - by Tim Brigham

  I have two drives used for SQL backups which for the last week have been acting strange - the free space indicated by windows is far off from what windirstat, etc indicates. There should only be about 60 GB of drive space used and there is about 160. This would match the utilization if the two last backup files were still residing on disk. SQL server is 2000, OS Server 2003 x64. Running on a VMware 5.0 cluster. OSSEC and McAfee for this system shows clean. My current plan is to temporarily attach one of these drives this drive to another VM for analysis. Is there anything more I should be looking at? There were a lot of pages on the net when I was looking for documentation on this issue but I haven't found this case described. EDIT: Unfortunately even a full reboot did not clear this behavior. I also used process explorer to look for open file handles. No dice.

  Read the article

• unable to access Internet by wireless but can by cable

  - by Jeff King

  i'M GOING MAD! UNtil last friday I had been successfully using wifi with the supplier as VIRGIN through their Motorola SB 4200 cable Modem and the wireless router being the Linksys WRT 54G router. Supported were three lap tops and an EPSON 510W printer and this had been running with no issue for about 3 years. Back to last friday, we started suffering significant delays and then the network collapsed with no wireless access. I was able to connect a single laptop direct to the cable modem and internet access was restored to just that one device. I thought that the problem was the router so I tried a backup D-Link device with no success. I have subsequently bought another cable modem AND a netgear router plus addidtional ethernet cables but with no success. The best that happens is that the signal appears good but I cannot get access to the internet. A yellow question mark appears on the 'gradient' icon. Each laptop and router works elsewhere so I'm stumped. Mind you I am a real novice so I'm not surprised. Please can anyone tell me what I'm doing wrong?

  Read the article

• Multiple Remote Desktop Connection in Windows Server 2003?

  - by Joel Bradley

  My company is transitioning all user PC's to Windows 7 64-Bit in anticipation of the 2014 cutoff for Windows XP support. So far everything has been going great except for one specific piece of software that will not run in Windows 7. The current plan is to give everyone a cheap secondary PC to run this software but I feel that's a little much for software that's not even used all the time, although it is essential. I've suggested we install virtual machines but the company does not want to pay for the XP licences. I have access to a copy of Windows Server 2003 that is no longer being used and I was wondering if it was possible to create a remote desktop server. I know it can be done on a one-to-one basis, but this is a 15 person helpdesk. I'd like to be able to support multiple remote dekstop sessions, each with their own logins and dekstops. Is this possible? Are there any other alternatives to my issue? FYI, I've been told that XP mode is only free for consumers. There are costs when used in a corporate environment.

  Read the article

• Error in mysql "max_allowed_packet" VPS godaddy

  - by focusmantra

  I am getting error "Serious session error detected. Please notify administrator, this problem is most probably caused by small value in max_allowed_packet MySQL setting. " This error generally comes after every 20-25 minutes and when it comes , it logs out the user and then logs in again, starts again and then after sometime the same issue occurs again. I tried changing max_allowed_packet setting but getting error "access denied; You need SUPER privilege for this operation'. I even tried SET SESSION too but error "SESSION variable 'max_allowed_packet' is read-only. Use SET GLOBAL to assign the value" I have hosted the website on godaddy VPS centos and access it via putty or cpanel. Website is made in moodle 2.0.3 i.e. php. My developers use to fix this but warned will occur when server restart. As godaddy ppl say move to dedicated and then i can do but as I don't have any money so can't at present. I trying to find how developers used to do for temporary fix that is until server restart.

  Read the article

• ext3: maximum recommended partition size / handling large partitions

  - by Hansi

  Hi! I would like to do an encrypted install of Ubuntu on a 2 Terabyte drive (i.e., using LUKS/DMcrypt). In order to not have to type in passwords too often, the partitioning scheme will be 50 GB for / and about 1 TB for /home (and the rest for Windows 7), just for clarity. Even though by now LVM is regarded as being stable, I don't want to bother having more room for errors by introducing unnecessary layers of complexity. For both Ubuntu partitions I want encrypted ext3 with the default blocksize of ext3 (4k?). Thoughts: When I look at most partition schemes here on this site or elsewhere, I usually see at most about 400 or 500 GB partitions (maybe I didn't see enough). There may be different reasons for this, but is reliability an issue here? Are larger ext3 partitions, like about 1 TB, harder to handle for the OS or filesystem driver or at some other level? If I make the partition too large, will it be harder to repair in case of corruptions? Are there some default settings for ext3 that I should change for 1 TB partitions? Question: What maximum partition size for ext3 do you recommend and why? Thanks!

  Read the article

• IIS 7 and ASP.NET State Service Configuration

  - by Shawn

  We have 2 web servers load balanced and we wanted to get away from sticky sessions for obvious reasons. Our attempted approach is to use the ASP.NET State service on one of the boxes to store the session state for both. I realize that it's best to have a server dedicated to storing sessions but we don't have the resources for that. I've followed these instructions to no avail. The session still isn't being shared between the two servers. I'm not receiving any errors. I have the same machine key for both servers, and I've set the application ID to a unique value that matches between the two servers. Any suggestions on how I can troubleshoot this issue? Update: I turned on the session state service on my local machine and pointed both servers to the ip address on my local machine and it worked as expected. The session was shared between both servers. This leads me to believe that the problem might be that I'm not using a standalone server as my state service. Perhaps the problem is because I am using the ip address 127.0.0.1 on one server and then using a different ip address on the other server. Unfortunately when I try to use the network ip address as opposed to localhost the connection doesn't seem to work from the host server. Any insight on whether my suspicions are correct would be appreciated.

  Read the article

• SVG doesn't work on subdomain - some browsers try to download rather than display

  - by John Catterfeld

  I have a site with a 'development' subdomain, which displays my SVG file exactly as intended. However when I copy it across to www, or any other subdomain (e.g. 'test') some browsers try to open the file in an external editor, therefore asking me to download the file rather than displaying it. For example: http://development.mysite.com/test.svg - works http://www.mysite.com/test.svg - doesn't work The SVG file: <?xml version="1.0" standalone="no"?> <!DOCTYPE svg PUBLIC "-//W3C//DTD SVG 1.1//EN" "http://www.w3.org/Graphics/SVG/1.1/DTD/svg11.dtd"> <svg xmlns="http://www.w3.org/2000/svg" version="1.1"> <circle cx="100" cy="50" r="40" stroke="black" stroke-width="2" fill="red" /> </svg> This happens in Firefox, Chrome and Safari, however IE9 and above display the file as intended. It is a Windows hosting, and I have <mimeMap fileExtension=".svg" mimeType="image/svg+xml" /> in my web.config file My hunch is that there must be some setting on the server which I need my hosting company to make. Can anyone suggest what might cause this issue?

  Read the article

• Why isn't my phone charging with some micro usb cables?

  - by Jacxel

  I ordered 3 microUSB cables over ebay. My phone was at about 50% battery and I wanted to use it as a hot spot for some browsing on my laptop, so I plugged it in, a charging icon appeared on the phone, my laptop showed it as a connected usb device and so I went about my business. About 30 minutes later I checked the phone and to my dismay saw 45% battery. But ahh, I thought, I have been putting the poor little thing under too much pressure, acting as a WiFi hotspot must drain the battery quicker than it can charge via usb, perhaps even using my laptops usb port wouldn't output enough power. Unscathed I continued on and when I was going to bed I plugged the usb cable into a mains adapter and switched everything battery consuming off and content, went to sleep. The next morning I was awoken by my phones alarm which got cut off unexpectedly. I attempted to unlock my phone which showed no more signs of life. Why isn't my phone charging with these new USB cables? For clarity: They transfer data with no problems The phone appears to be charging, showing all the signs and lights it normally would, the cable that came with the phone works as you would expect, so its not a fault with the phone, I think they slow the discharging of the phone, but I could be wrong. Are these just bad quality cables? Is there a way to fix this issue?

  Read the article

• Choose a VPN software on CentOs 6.5

  - by loyCossou

  We are installing a SMS gateway with Kannel, on a CentOs 6.5 server, which is supposed to connect via SMPP to our local operators. Kannel is working fine and no probleme there. Now 2 operators are asking to connect via a VPN for obvious security reasons; actually they asked for or VPN details so they can connect to it... Now, I am looking for a free VPN that I can setup and configure on our server... I saw Open VPN that I already started configuring, no issue... But just saw on Wikipedia (http://en.wikipedia.org/wiki/OpenVPN#Platforms) that OpenVPN is not compatible with other VPN packages. Now my question is: 1- I am absolutely new to VPN technologies. Is OpenVPN a good choice in my situation? 2- If I configure OpenVPN on my server, will it be possible to any client to connect to my server? 3- Anyone have any advice for me? Thank you for this great community.

  Read the article

• Git clone/pull across local network

  - by Tom Sarduy

  I'm trying to clone/pull a repository in another PC using Ubuntu Quantal. I have done this on Windows before but I don't know what is the problem on ubuntu. I tried these: git clone file:////pc-name/repo/repository.git git clone file:////192.168.100.18/repo/repository.git git clone file:////user:pass@pc-name/repo/repository.git git clone smb://c-pc/repo/repository.git git clone //192.168.100.18/repo/repository.git Always I got: Cloning into 'intranet'... fatal: '//c-pc/repo/repository.git' does not appear to be a git repository fatal: The remote end hung up unexpectedly or fatal: repository '//192.168.100.18/repo/repository.git' does not exist More: The other PC has username and password Is not networking issue, I can access and ping it. I just installed git doing apt-get install git (dependencies installed) I'm running git from the terminal (I'm not using git-shell) What is causing this and how to fix this? Any help would be great! UPDATE I have cloned the repo on Windows using git clone //192.168.100.18/repo/intranet.git without problems. So, the repo is accessible and exist! Maybe the problem is due user credentials?

  Read the article

• Please help to find a solution for two way, real-time synchronization on Centos 5.5 64Bit

  - by Vipul Limbachiya

  I am in need of a real time, two way synchronization software for Centos 5.5 / 64Bit. Here's little explanation: It needs to be able to perform: Two way synchronization. It must be realtime. By realtime means it can be almost realtime, i.e. a delay of 1 second for example is fine. And the folders are on the same server. I am currently using GlusterFS across two webservers. However, it has extremely poor small file read performance and it's slowing down my website. There's nothing more that can be done to improve this, I have already tested many configurations. As a solution, I was going to mount a RAM drive (tmpfs) that mirrors the GlusterFS web files but get the webserver to use the RAM drive. The issue is that I need two way realtime mirroring or replication between glusterfs and the RAM drive. I need this is as Apache writes files as wells. As I said, realtime two way synchronization across two folders. Which are in fact 2 different mounts points. The RAM (tmpfs) mount poing and the GlusterFS mount point. I already know about: Rsync - Which is one way Unison - Which is not realtime Please suggest me any solution free or paid. Thanks in advance

  Read the article

• Why does Windows Event Log stop logging events before maximum log size is reached?

  - by Tuure Laurinolli

  I have a service that produces a lot of event log output. Currently the event log is configured to overwrite any old events to keep the log from ever getting full. We have also increased the event log size considerably (to about 600 MB). Recently the service started reporting errors to its clients, and the error message it was sending to its clients is "The event log file is full". How can this be, when event log is configured to overwrite as necessary? In our hurry to get the service back up we cleared the event log without saving its contents, but most likely it had not reached 600 MB yet, judging from sizes of some earlier log dumps. There is also MS KB entry 312571, which reports that a hot fix to a similar issue is available, but the the configuration that the fix applies to is not exactly the same we have. Specifically, the fix only applies if event logs are configured to never overwrite old events. I wonder if this has something to do with the fact that the log files apparently are memory-mapped. What happens if the system runs out of address space to map files to?

  Read the article

• How can I implement ansible with per-host passwords, securely?

  - by supervacuo

  I would like to use ansible to manage a group of existing servers. I have created an ansible_hosts file, and tested successfully (with the -K option) with commands that only target a single host ansible -i ansible_hosts host1 --sudo -K # + commands ... My problem now is that the user passwords on each host are different, but I can't find a way of handling this in Ansible. Using -K, I am only prompted for a single sudo password up-front, which then seems to be tried for all subsequent hosts without prompting: host1 | ... host2 | FAILED => Incorrect sudo password host3 | FAILED => Incorrect sudo password host4 | FAILED => Incorrect sudo password host5 | FAILED => Incorrect sudo password Research so far: a StackOverflow question with one incorrect answer ("use -K") and one response by the author saying "Found out I needed passwordless sudo" the Ansible docs, which say "Use of passwordless sudo makes things easier to automate, but it’s not required." (emphasis mine) this security StackExchange question which takes it as read that NOPASSWD is required article "Scalable and Understandable Provisioning..." which says: "running sudo may require typing a password, which is a sure way of blocking Ansible forever. A simple fix is to run visudo on the target host, and make sure that the user Ansible will use to login does not have to type a password" article "Basic Ansible Playbooks", which says "Ansible could log into the target server as root and avoid the need for sudo, or let the ansible user have sudo without a password, but the thought of doing either makes my spleen threaten to leap up my gullet and block my windpipe, so I don’t" My thoughts exactly, but then how to extend beyond a single server? ansible issue #1227, "Ansible should ask for sudo password for all users in a playbook", which was closed a year ago by mpdehaan with the comment "Haven't seen much demand for this, I think most people are sudoing from only one user account or using keys most of the time." So... how are people using Ansible in situations like these? Setting NOPASSWD in /etc/sudoers, reusing password across hosts or enabling root SSH login all seem rather drastic reductions in security.

  Read the article

< Previous Page | 902 903 904 905 906 907 908 909 910 911 912 913  | Next Page >