Search Results

Search found 28170 results on 1127 pages for '16 bit animation'.

Page 380/1127 | < Previous Page | 376 377 378 379 380 381 382 383 384 385 386 387  | Next Page >

• GA 8KNXP Rev1.0: 4GB installed, only 3.5 recognized by BIOS

  - by hurikhan77

  I've installed 2x 1 GB and 4x 512 MB memory into my GA-8KNXP system which would sum up to 4GB. The specs from the manual say: Maximum memory support: 4GB. If all six slots are utilized, slot 5+6 may only equipped with single-sided RAM modules. And so I did. Anyway: The BIOS counts up to 3.5 GB and finishes there. Also my linux system reports only 3.5 GB of memory although 4 GB memory support is activated in the kernel. So I suppose this is a memory mapping issue or a hardware issue. I've tried removing only on of the 512 MB memory modules leaving 5 modules in place. But that just stopped the system from powering on correctly (screen stays black although fans and leds come to live). Dual Channel was detected and enabled so the system technically found all 6 modules. "dmidecode" in linux reports only memory in slots 1 to 4 and ignores slots 5+6, so it only detects 3 GB of memory. It also says the system would support up to 16 GB of memory with 4 GB modules per slot. I think technically the chipset should be able to offer and utilize the complete 4 GB memory range. Any clues what else I could check? Or do I have just to live with 0.5 GB wasted memory?

  Read the article

• Pip installs on Archlinux fails to build egg

  - by stmfunk

  I was trying to install nltk on my Archlinux server but it repeatedly fails with the following error output /usr/lib/python3.3/distutils/dist.py:257: UserWarning: Unknown distribution option: 'entry_points' warnings.warn(msg) /usr/lib/python3.3/distutils/dist.py:257: UserWarning: Unknown distribution option: 'zip_safe' warnings.warn(msg) /usr/lib/python3.3/distutils/dist.py:257: UserWarning: Unknown distribution option: 'test_suite' warnings.warn(msg) usage: setup.py [global_opts] cmd1 [cmd1_opts] [cmd2 [cmd2_opts] ...] or: setup.py --help [cmd1 cmd2 ...] or: setup.py --help-commands or: setup.py cmd --help error: invalid command 'bdist_egg' /tmp/pip_build_root/nltk/distribute-0.6.21-py3.3.egg Traceback (most recent call last): File "./distribute_setup.py", line 143, in use_setuptools raise ImportError ImportError During handling of the above exception, another exception occurred: Traceback (most recent call last): File "", line 16, in File "/tmp/pip_build_root/nltk/setup.py", line 23, in distribute_setup.use_setuptools() File "./distribute_setup.py", line 145, in use_setuptools return _do_download(version, download_base, to_dir, download_delay) File "./distribute_setup.py", line 125, in _do_download _build_egg(egg, tarball, to_dir) File "./distribute_setup.py", line 116, in _build_egg raise IOError('Could not build the egg.') OSError: Could not build the egg. ---------------------------------------- Cleaning up... Command python setup.py egg_info failed with error code 1 in /tmp/pip_build_root/nltk Storing complete log in /root/.pip/pip.log This error is also occurring for matplotlib buts thats the only other library I found it to fail on so far. pyyaml installs fine. The install works perfectly under virtualenv on my mac which is using python 2.7 but the server is using python 3.3. Any help is appreciated.

  Read the article

• SQL SERVER 2005 with Windows 7 Problems

  - by azamsharp

  First of all I restored the database from other server and now all the stored procedures are named as [azamsharp].[usp_getlatestposts]. I think [azamsharp] is prefixed since it was the user on the original server. Now, on my local machine this does not run. I don't want the [azamsharp] prefix with all the stored procedures. Also, when I right click on the Sproc I cannot even see the properties option. I am running the SQL SERVER 2005 on Windows 7. UPDATE: The weird thing is that if I access the production database from my machine I can see the properties option. So, there is really something wrong with Windows 7 security. UPDATE 2: When I ran the orphan users stored procedure it showed two users "azamsharp" and "dbo1". I fixed the "azamsharp" user but "dbo1" is not getting fixed. When I run the following script: exec sp_change_users_login 'update_one', 'dbo1', 'dbo1' I get the following error: Msg 15291, Level 16, State 1, Procedure sp_change_users_login, Line 131 Terminating this procedure. The Login name 'dbo1' is absent or invalid.

  Read the article

• nfs mount with nfs 3

  - by rahrahruby

  I am running CentOS 6.4 Kernel version 2.6.32-358.23.2.el6.x86_64 #1 SMP and have the following nfs info: nfs-utils-lib-1.1.5-6.el6.x86_64 nfs4-acl-tools-0.3.3-6.el6.x86_64 nfs-utils-1.2.3-36.el6.x86_64 and am trying to mount an nfs volume with nfs3. I have the following line in my fstab: 172.16.11.87:/volume1/web /home/nas nfsver=3 rsize=8192,wsize=8192,timeo=14,intr(no_root_squach) When I run nfsstat it still shows the client as nfs4 Server rpc stats: calls badcalls badauth badclnt xdrcall 0 0 0 0 0 Client rpc stats: calls retrans authrefrsh 1988817 6 1988818 Client nfs v4: null read write commit open open_conf 0 0% 36943 1% 21606 1% 401 0% 392369 19% 375986 18% open_noat open_dgrd close setattr fsinfo renew 0 0% 0 0% 387945 19% 22904 1% 3 0% 2914 0% setclntid confirm lock lockt locku access 1 0% 1 0% 0 0% 0 0% 0 0% 97856 4% getattr lookup lookup_root remove rename link 613996 30% 29888 1% 1 0% 1248 0% 253 0% 414 0% symlink create pathconf statfs readlink readdir 26 0% 226 0% 2 0% 3 0% 0 0% 3825 0% server_caps delegreturn getacl setacl fs_locations rel_lkowner 5 0% 0 0% 0 0% 0 0% 0 0% 0 0% exchange_id create_ses destroy_ses sequence get_lease_t reclaim_comp 0 0% 0 0% 0 0% 0 0% 0 0% 0 0% layoutget layoutcommit layoutreturn getdevlist getdevinfo ds_write 0 0% 0 0% 0 0% 0 0% 0 0% 0 0% ds_commit 0 0%

  Read the article

• Anonymous FTP upload on CentOS 5.2

  - by Craig

  I need to allow users to upload files to an FTP server anonymously. They should not be able to see any other files, or download files. It is a CentOS 5.2 server. I have a separate partition for the the upload area (mounted at /ftp). I have tried to set up vsftpd, followed all the instructions/advice I could find. But, when a user logs in and tries to transfer a file it throws a "553 could not create file." error. If I do a 'pwd' it shows the directory as "/" rather than the anon_root of "/ftp/anonymous". Any attempt to change the remote directory ends with "550 Failed to change directory.". I have a subdirectory "/ftp/anonymous/incoming" that is writable for the uploads SELinux is in permissive mode. I am running version 2.0.5 release 16.el5 of vsftpd. Here is the vsftpd.conf file: anonymous_enable=YES local_enable=YES write_enable=YES local_umask=002 anon_umask=007 file_open_mode=0666 anon_upload_enable=YES anon_mkdir_write_enable=NO dirmessage_enable=YES xferlog_enable=YES connect_from_port_20=YES chown_uploads=YES chown_username=inftpadm xferlog_std_format=YES nopriv_user=nobody listen=YES pam_service_name=vsftpd userlist_enable=YES tcp_wrappers=YES ftp_username=inftpadm anon_root=/ftp/anonymous anon_other_write_enable=NO anon_mkdir_write_enable=NO anon_world_readable_only=NO dirlist_enable=YES Can anyone help?

  Read the article

• Very different results from df after a few seconds

  - by tatus2

  When the backup moves the files from one server to the other the results from df change every few seconds in an impossible manner. The source host is running rsync. On the destination host I'm running the following command every few seconds: echo `date` `df|grep md0` Results are below: Sat Jun 29 23:57:12 CEST 2013 /dev/md0 4326425568 579316100 3527339636 15% /MD0 Sat Jun 29 23:57:14 CEST 2013 /dev/md0 4326425568 852513700 3254142036 21% /MD0 Sat Jun 29 23:57:15 CEST 2013 /dev/md0 4326425568 969970340 3136685396 24% /MD0 Sat Jun 29 23:57:17 CEST 2013 /dev/md0 4326425568 1255222180 2851433556 31% /MD0 Sat Jun 29 23:57:20 CEST 2013 /dev/md0 4326425568 1276006720 2830649016 32% /MD0 Sat Jun 29 23:57:24 CEST 2013 /dev/md0 4326425568 1355440016 2751215720 34% /MD0 Sat Jun 29 23:57:26 CEST 2013 /dev/md0 4326425568 1425090960 2681564776 35% /MD0 Sat Jun 29 23:57:27 CEST 2013 /dev/md0 4326425568 1474601872 2632053864 36% /MD0 Sat Jun 29 23:57:28 CEST 2013 /dev/md0 4326425568 1493627384 2613028352 37% /MD0 Sat Jun 29 23:57:32 CEST 2013 /dev/md0 4326425568 615934400 3490721336 15% /MD0 Sat Jun 29 23:57:33 CEST 2013 /dev/md0 4326425568 636071360 3470584376 16% /MD0 As you can see I start from USE of 15% and after 15 seconds I'm at 37% (I don't need to mention that the backup can not copy this huge amount of data in such a short time). After ~20 seconds the cycle closes. I'm again roughly at the same usage as earlier. The value is reasonable, ca. 35 Mb were copied. Can somebody explain to me what is going on? Does df only make an estimation of usage instead of used value?

  Read the article

• How do I clear out the ssh-agent entries (on Mac OS X )?

  - by cwd

  I'm running Mac OS X, and it appears that after SSHing to several machines, using identity files, my 'ssh-agent' builds up a lot of identity / keys and then sometimes offers too many to a remote machine, causing them to kick me off before connecting: Received disconnect from 10.12.10.16: 2: Too many authentication failures for cwd It's pretty obvious what's happening, and this page talks about it in more detail: SSH servers only allow you to attempt to authenticate a certain number of times. Each failed password attempt, each failed pubkey/identity that is offered, etc, take up one of these attempts. If you have a lot of SSH keys in your agent, you may find that an SSH server may kick you out before allowing you to attempt password authentication at all. If this is the case, there are a few different workarounds. Rebooting clears the agent and then everything works OK again. I can also add this line to my .ssh/config file to force it to use password authentication: PreferredAuthentications keyboard-interactive,password Anyhow, I saw the note on the page I referenced talking about deleting keys from the agent, but I'm not sure if that applies on a Mac since they appear to be cleared after reboot anyhow. Is there a simple way to clear out all keys in the 'ssh-agent' (the same thing that happens at reboot)?

  Read the article

• Once VPN connection is done, how do I proceed reaching the other side address space?

  - by sports

  I'm using Windows Azure and I created a VPN Site To Site, configured like this: My virtual network: My address space: 10.2.0.0/16 (65531) Subnet1: 10.2.1.0/24 (251) Subnet2: 10.2.2.0/24 (251) Gateway: 10.2.3.0/29 (3) My public gateway IP: 137.135.x.z (I wont show x and z for security reasons) This public gateway uses, as you can see, 5 IPs on subnet1 and 5 IPs on subnet2, and 5 IPs on the gateway "Their" virtual network (in azure this would be a "Local network") Their address space: 172.60.100.67/32, 172.60.100.68/32, 172.60.100.69/32 Their device public IP: x.x.x.x (ommited for security reasons) Notice their address space are 3 IPs So: the VPN is "in green" (in Azure is showing up green, literally, like these two are connected) and now my question is: How do I proceed to reach their address space? I've tried creating a virtual machine (Windows Server 2008, but it could be an Ubuntu) on "my" virtual network and it is automatically "placed" on subnet1 or subnet2. So it gets the IP 10.2.1.0 (valid example), I can't choose to place the virtual machine in the gateway address space. How do I "reach" any of the IPs 172.60.100.67, 172.60.100.68, 172.60.100.69 ? In other words: How can I telnet any of these IPs? or ping? or see them in my network? Please provide me answers for Windows Server 2008 or for an Ubuntu. I'm open to create any virtual machine.

  Read the article

• heavy load on mysql

  - by payal

  i have dedicated server with very good configuation like 16 gb ram etc but i am facing heavy load from mysql i am running a music wesbite however only one database is running and 5-10 pages are only running.when i click on whm show processlist it shows only 2-3 processes However whm load is always less than one but when i click on whm load it shows 20% of cpu usage by mysql and after some time it starts saying can not connect to mysql . mysql server has gone away 1691 (Trace) (Kill) mysql 0 19.2 2.7 /usr/sbin/mysqld --basedir=/ --datadir=/var/lib/mysql --user=mysql --log- error=/var/lib/mysql/server.xyz.com.err --pid-file=/var/lib/mysql/server.xyz.com.pid i have tested static pages they are coming blezing fast but all dynamic pages which are using mysql is coming damn slow it takes years to open.. my.conf file is [mysqld] key_buffer = 1536M max_allowed_packet = 1M max_connections = 250 max_user_connections = 15 wait_timeout=40 connect_timeout=10 table_cache = 512 sort_buffer_size = 2M read_buffer_size = 2M read_rnd_buffer_size = 8M myisam_sort_buffer_size = 64M thread_cache_size = 8 query_cache_size = 32M server-id = 14 old-passwords = 1 [mysqldump] quick max_allowed_packet = 16M [mysql] no-auto-rehash [myisamchk] key_buffer = 256M sort_buffer_size = 256M read_buffer = 2M write_buffer = 2M [mysqlhotcopy] interactive-timeout ihave checked log error file it says nothing.i have increased maximum connnection also to 1000 but still same problem is there .if i disconnect that one databasejust by changing the name of database i can see withing half hour the load of server and mysql goes down to negliglble .i have tested everything and if there are some query which can cause heavy load to server can you please list which type of query can cause heavy load on server then also for 5-10 pages it will never cause that much heavy load. i have seen server with 500 websites but was working just fine.

  Read the article

• heavy load on mysql

  - by payal

  i have dedicated server with very good configuation like 16 gb ram etc but i am facing heavy load from mysql however only one database is running and 5-10 pages are only running. However whm load is always less than one but when i click on whm load it shows 20% of cpu usage by mysql and after some time it starts saying can not connect to mysql . mysql server has gone away 1691 (Trace) (Kill) mysql 0 19.2 2.7 /usr/sbin/mysqld --basedir=/ --datadir=/var/lib/mysql --user=mysql --log- error=/var/lib/mysql/server.xyz.com.err --pid-file=/var/lib/mysql/server.xyz.com.pid i have tested static pages they are coming blezing fast but all dynamic pages which are using mysql is coming damn slow it takes years to open.. ihave checked log error file it says nothing.i have increased maximum connnection also to 1000 but still same problem is there .if i disconnect that one databasejust by changing the name of database i can see withing half hour the load of server and mysql goes down to negliglble .i have tested everything and if there are some query which can cause heavy load to server can you please list which type of query can cause heavy load on server then also for 5-10 pages it will never cause that much heavy load. i have seen server with 500 websites but was working just fine.

  Read the article

• Unable to record using Jmeter: [help me very urgent]

  - by krish

  Hi, I am trying to record a http web page using Jmeter 2.3.3 version.I has setup the JMeter proxy and tried, but did n't work. I have followed the below steps. 1. Launch jmeter 2.3.3, added thred group to test plan 2. Under Workbench-add-non-test elements- added HTTP proxy server. proxy server setting are port:9090, target:use recording controller, grouping:donot group samplers, Type:HTTp request and checked the boxes of all under http sampler settings 3.Saved the settings 4. Now in browser(IE 7.0 or firefox 3.0.16), under connection settings, setup the manual proxy settings as local host and port as 9090(no auto detect settings nothing, only manual proxy). Setting saved 5.Now in the jmeter, started the http proxy server. 6. Open a browser and hit the webpage needs to be tested. The page is not opened. In fact because of the changes made in browsers, no pages are opened. Whenever i try hitting a page, the pages are recorded in the Jmeter. but without the page open, how can i test. I looking for an immediate answer and my work is blocked. Immediate answer would be appreciated.

  Read the article

• Desktop PC does not power up on power button

  - by hIpPy

  When I press the power button on my desktop, it does not power up completely. Before I press the power button, I see lights on the motherboard. Everything is normal. On power button press, the fans on the cpu, graphics card and motherboard start to spin a little for a second or two and then they stop. No beeps during this process. It has been doing this for a while now but it used to start up after some trials. Once it starts up, I have NO issues at all like random shutdowns so it is not an issue with OS. Update: I left the desktop off for a few days and it started. I'm just guessing here but it seems as if the PSU (Antec TP2-550ATX) is dying out and does not have enough power now - just a guess. It's an old desktop assembled in 2005 but I have maintained it well. Update: I always keep the desktop running and I never shut it down. During updates or manual restarts, it powers up without issues. I wonder if this sheds lights on the issue. Any idea how I can narrow down the issue? ex: if I can find if the PSU is dying etc. I'd really like to fix the issue. Please help. Thanks. Below is the complete configuration. DFI LAN-Party UT NF4 Ultra-D 6/23 {6.70}, Evercool EC-VC-RE 41/47C, AMD Opteron 170 2.0GHz {1.3.2.16} 1.312V 36/41C, ThermalRight SI-120, Panaflo 120×38mm OCZ Platinum 2×1GB 200MHz 2.66V 3-3-2-7 1T XFX 7800GTX 256MB 475/1250MHz {91.31}, Zalman VF900 Cu led 41/56C WD Caviar 320GB 7200RPM 16MB SATA 3Gb/s Antec TP2-550ATX Antec P180 WinXP sp3 Logitech MX310 Razer Mantis Speed BenQ FP91G+ 19" LCD 8ms DVI Creative Audigy2 ZS {4.42} BenQ DW1640 Logitech z-5300e 5.1 280W Legend: Driver versions: {} User settings: [] Voltage: V Wattage: W Temperature: C (Celsius) min/max

  Read the article

• OS X can connect to Windows machine, but can't access shared folders

  - by Bonnie

  I can create new folders on my Windows XP machine, set them to "shared". On my Mac, I pick Finder → Go → Connect to Server → smb://192.168.1.4 → Connect → Name / Password. It even shows me all the names of the newly created shared-folders on my PC, but when I try to actually connect to any of them I get connection failed, there was an error connecting Any idea on what would cause that? The fact that it successfully gets so far—to actually showing me my PC share-names—must mean I have 99% of this working correctly, i.e. the physical connection, the IP address, the user name, the password, etc. Still, I can't seem to access the folders themselves. I've tried this with my Windows XP firewall on/off, and Norton AntiVirus on/off. Same problem. Everything did work fine, 4 months ago. Were there any odd OS X or Windows updates released recently? I always apply them all. smbclient on the Mac does correctly find the XP machine, my XP user name, and accepts my XP password. I get the following from that smbclient command: Doing spnego session setup (blob length=16) server didn't supply a full spnego negprot Got challenge flags: ... Got NTLMSSP flags: ... Got NTLMSP flags: ... Domain=[XPMACHINE] OS=[Windows 5.1] Server=[Windows 2000 LAN Manager] tree connect failed: NT_STATUS_INSUFF_SERVER_RESOURCES I'm not sure why a standard XP box can't "supply a full spnego negprot". Whatever that means. Using XP's RegEdit to change my IRPStackSize from 11... to 13, 15, 20, 22... still gives that "NT_STATUS_INSUFF_SERVER_RESOURCES" error on the Mac.

  Read the article

• 10GE network: Is it still deadly expensive? Any options?

  - by BarsMonster

  Hi! I am building home cluster where I going to have about 16 nodes which can live with 1G ports, but I really want to have 10GE on file server & central node. It's all local, so no need for cabels longer than 3-5m. And ofcourse I want to spend as little money as possible (not going to spend more than whole cluster costs) :-) What are my options? 1) Legacy solution is to take some 24-48 port 1GE switch, and connect to file/central nodes via 4-8 aggregated links. This will work I guess, cost is very acceptable, but I am not sure if it's ok to use that much aggregated links. And ofcourse it would be hard to double bandwidth when needed... :-D 2) Switch with several 10GE uplink 'ports'. As far as I see, they all require modules which costs about 1000$, so I will need 4 10G modules, and 2 10GE cards... Smells like way more than 5000$+... 3) Connect file & central node via 2 10G cards directly, and put 4 quadport 1GE NICs on fileserver. I am saving on 2 10G modules and a switch, fileserver will have to do packet routing, but it's still gonna have alot of CPU's left :-) 4) Any other options? Infiniband? 5) Are MyriNet adaptors works fine? I guess there are no cheaper options? 6) Hmm... Scrap fileserver, put it all on central node and provide dedicated 1GE port for each of the nodes... This is sad...

  Read the article

• How to find out what is causing a slow down of the application on this server?

  - by Jan P.

  This is not the typical serverfault question, but I'm out of ideas and don't know where else to go. If there are better places to ask this, just point me there in the comments. Thanks. Situation We have this web application that uses Zend Framework, so runs in PHP on an Apache web server. We use MySQL for data storage and memcached for object caching. The application has a very unique usage and load pattern. It is a mobile web application where every full hour a cronjob looks through the database for users that have some information waiting or action to do and sends this information to a (external) notification server, that pushes these notifications to them. After the users get these notifications, the go to the app and use it, mostly for a very short time. An hour later, same thing happens. Problem In the last few weeks usage of the application really started to grow. In the last few days we encountered very high load and doubling of application response times during and after the sending of these notifications (so basically every hour). The server doesn't crash or stop responding to requests, it just gets slower and slower and often takes 20 minutes to recover - until the same thing starts again at the full hour. We have extensive monitoring in place (New Relic, collectd) but I can't figure out what's wrong; I can't find the bottlekneck. That's where you come in: Can you help me figure out what's wrong and maybe how to fix it? Additional information The server is a 16 core Intel Xeon (8 cores with hyperthreading, I think) and 12GB RAM running Ubuntu 10.04 (Linux 3.2.4-20120307 x86_64). Apache is 2.2.x and PHP is Version 5.3.2-1ubuntu4.11. If any configuration information would help analyze the problem, just comment and I will add it. Graphs info phpinfo() apc status memcache status collectd Processes CPU Apache Load MySQL Vmem Disk New Relic Application performance Server overview Processes Network Disks (Sorry the graphs are gifs and not the same time period, but I think the most important info is in there)

  Read the article

• big cpu load on vmware server / linux

  - by dezfafara

  Hi, I currently using a server 2.x hosting 4 virtual machines on a linux system Today, on my physical server, I saw an enormous load average: this is the "top" of the server, illustrating my 4 virtual guests. top - 11:02:02 up 194 days, 23:09, 5 users, load average: 18.78, 12.05, 13.55 Tasks: 113 total, 4 running, 109 sleeping, 0 stopped, 0 zombie Cpu0 : 71.6%us, 19.0%sy, 0.0%ni, 8.8%id, 0.0%wa, 0.3%hi, 0.3%si, 0.0%st Cpu1 : 74.3%us, 10.4%sy, 0.0%ni, 15.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu2 : 72.5%us, 17.6%sy, 0.0%ni, 9.8%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu3 : 79.5%us, 4.6%sy, 0.0%ni, 16.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 8178884k total, 8129980k used, 48904k free, 134904k buffers Swap: 10490436k total, 148k used, 10490288k free, 6129728k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 7312 root 6 -10 1149m 921m 559m R 97 11.5 107947:09 vmware-vmx 6995 root 6 -10 779m 687m 317m R 92 8.6 107374:31 vmware-vmx 6693 root 6 -10 880m 659m 409m S 85 8.3 76947:33 vmware-vmx 12937 root 6 -10 960m 719m 523m S 75 9.0 67219:49 vmware-vmx In bold are the cpu usage for my 4 virtuals guests These guests are running on a linux system, and the appropriate process are usually 5% - 15% of cpu I don't understang why , since a few days I have this big problem. This is the "top" on a virtual guest which is at 95% of cpu load top - 11:23:15 up 194 days, 23:13, 4 users, load average: 0.25, 0.47, 0.59 Tasks: 92 total, 2 running, 90 sleeping, 0 stopped, 0 zombie Cpu(s): 1.4%us, 7.7%sy, 0.0%ni, 90.5%id, 0.5%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 382296k total, 369732k used, 12564k free, 145156k buffers Swap: 979924k total, 13956k used, 965968k free, 86988k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 3691 root 20 0 23948 1148 960 S 13.0 0.3 15339:23 vmware-guestd 3840 root 20 0 19880 584 512 S 7.7 0.2 1729:17 hald-addon-stor This virtual guest state is ok ... If anyone has any ideas .. Thanks

  Read the article

• Linux server: Dropped packets

  - by Lars

  I see dropped packets using ifconfig on my eth0 interface: eth0 Link encap:Ethernet HWaddr 00:15:17:0d:03:ca inet addr:10.0.1.2 Bcast:10.0.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:30268348 errors:0 dropped:70721 overruns:0 frame:0 TX packets:133076885 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8699434077 (8.6 GB) TX bytes:194937313025 (194.9 GB) Interrupt:16 Memory:feae0000-feb00000 When i use ethtool -S i dont see anything wrong: NIC statistics: rx_packets: 30267138 tx_packets: 133074510 rx_bytes: 8699356158 tx_bytes: 194934147340 rx_broadcast: 35296 tx_broadcast: 5435 rx_multicast: 0 tx_multicast: 0 rx_errors: 0 tx_errors: 0 tx_dropped: 0 multicast: 0 collisions: 0 rx_length_errors: 0 rx_over_errors: 0 rx_crc_errors: 0 rx_frame_errors: 0 rx_no_buffer_count: 0 rx_missed_errors: 0 tx_aborted_errors: 0 tx_carrier_errors: 0 tx_fifo_errors: 0 tx_heartbeat_errors: 0 tx_window_errors: 0 tx_abort_late_coll: 0 tx_deferred_ok: 0 tx_single_coll_ok: 0 tx_multi_coll_ok: 0 tx_timeout_count: 0 tx_restart_queue: 0 rx_long_length_errors: 0 rx_short_length_errors: 0 rx_align_errors: 0 tx_tcp_seg_good: 5757001 tx_tcp_seg_failed: 0 rx_flow_control_xon: 8649 rx_flow_control_xoff: 62072 tx_flow_control_xon: 0 tx_flow_control_xoff: 0 rx_long_byte_count: 8699356158 rx_csum_offload_good: 30212111 rx_csum_offload_errors: 0 rx_header_split: 10857552 alloc_rx_buff_failed: 0 tx_smbus: 0 rx_smbus: 0 dropped_smbus: 0 rx_dma_failed: 0 tx_dma_failed: 0 I am running Ubuntu 12.04 with kernel 3.2.0-30-generic #48-Ubuntu SMP I have pinged every device on my internal network for about 24 hours, without packet loss. Also checked my router and my interface to the WAN, also no errors there. Does anyone have any clue?

  Read the article

• How do I uncompress vmlinuz to vmlinux?

  - by Lord Loh.

  I have already tried uncompress, gzip, and all other solutions that come up as google results and these have not worked for me. To get just the image search for the GZ signature - 1f 8b 08 00. > od -A d -t x1 vmlinuz | grep '1f 8b 08 00' 0024576 24 26 27 00 ae 21 16 00 1f 8b 08 00 7f 2f 6b 45 so the image begins at 24576+8 => 24584. Then just copy the image from the point and decompress it - > dd if=vmlinuz bs=1 skip=24584 | zcat > vmlinux 1450414+0 records in 1450414+0 records out 1450414 bytes (1.5 MB) copied, 6.78127 s, 214 kB/s Got these instructions verbatim from a forum online: http://www.codeguru.com/forum/showthread.php?t=415186 This process does not work for me and end up giving errors that states file not found 0024576 and all subsequent numbers. How do I proceed extracting vmlinux from vmlinuz? Thank you. EDITED: This is a reverse engineering question. I have no access to the distro to install any RPM or recompile. I start with nothing but vmlinuz.

  Read the article

• 100% CPU load on Ubuntu 10.04.3 LTS 64bit

  - by deadtired

  I have 2 days since I am trying to fix this issue, with no success. The server is a mysql database server. Hardware: DELL Poweredge 1950, 2x Intel Xeon Quad Core E5345 @ 2.33GHz, 16 Gb mem, 2x 146Gb SAS (software RAID1) Software: Ubuntu 10.04.3 LTS, MySQL 5.1.41 Issue: while mysql is not used and runs with no database, everything seems alright. As soon as I install a database, it has the reason to bring all 8 cores in 100% with low memory consumption. So, you can imagine the load average goes high (I saw 212 load average for the first time). The server doesn't become unresponsive, but you can see it's slow while browsing the project installed. Additional info: the database used is not more than 24MB and it was moved from a server with less resources and a lot more larger databases. So it's not the database/project. my.cnf is not a reason also, as I used both default one and the one I use on the same distribution on another server.What is interesting is that mysql doesn't close any process and runs to the limit of the max_connections. Logs are quiet. Nothing there. I switched to this Ubuntu version after I suspected some problems in the newly Ubuntu 11.10 server. This one worked alright for an hour after I made a kernel upgrade to 3.0.1 (it was using the memory also) I tested disk speed and seems alright. Some more output on the running server: dstat -cndymlp -N total -D total 3: htop command: Idea? Did anyone meet the same problem? Any fix you can think of?

  Read the article

• Unable to record using Jmeter

  - by krish

  Hi, I am trying to record a http web page using Jmeter 2.3.3 version.I has setup the JMeter proxy and tried, but did n't work. I have followed the below steps. Launch jmeter 2.3.3, added thred group to test plan Under Workbench-add-non-test elements- added HTTP proxy server. proxy server setting are port:9090, target:use recording controller, grouping:donot group samplers, Type:HTTp request and checked the boxes of all under http sampler settings Saved the settings Now in browser(IE 7.0 or firefox 3.0.16), under connection settings, setup the manual proxy settings as local host and port as 9090(no auto detect settings nothing, only manual proxy). Setting saved Now in the jmeter, started the http proxy server. Open a browser and hit the webpage needs to be tested. The page is not opened. In fact because of the changes made in browsers, no pages are opened. Whenever i try hitting a page, the pages are recorded in the Jmeter. but without the page open, how can i test. I looking for an immediate answer and my work is blocked. Immediate answer would be appreciated.

  Read the article

• How to log kernel panics without KVM

  - by Spacedust

  My server is crashing and I can't find an answer why. It all started after my datacenter upgrade RAM from 16 GB to 32 GB. I also found such logs in dmesg - they've started to show itself just before the first kernel panic: EXT4-fs error (device md2): ext4_ext_find_extent: bad header/extent in inode #97911179: invalid magic - magic 5f69, entries 28769, max 26988(0), depth 24939(0) EXT4-fs error (device md2): ext4_ext_remove_space: bad header/extent in inode #97911179: invalid magic - magic 5f69, entries 28769, max 26988(0), depth 24939(0) EXT4-fs error (device md2): ext4_mb_generate_buddy: EXT4-fs: group 20974: 8589 blocks in bitmap, 54896 in gd JBD: Spotted dirty metadata buffer (dev = md2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. EXT4-fs error (device md2): ext4_ext_split: inode #97911179: (comm pdflush) eh_entries 28769 != eh_max 26988! EXT4-fs (md2): delayed block allocation failed for inode 97911179 at logical offset 1039 with max blocks 1 with error -5 This should not happen!! Data will be lost EXT4-fs error (device md2): ext4_mb_generate_buddy: EXT4-fs: group 21731: 5 blocks in bitmap, 60762 in gd JBD: Spotted dirty metadata buffer (dev = md2, blocknr = 0). There's a risk of filesystem corruption in case of system crash. My system is CentOS 5.8 64-bit with latest kernel 2.6.18-308.20.1.el5. How can I check what is the reason of kernel panic without having an access to the KVM ? I have told my datacenter admins to check the memory in the server.

  Read the article

• NetBackup's bplist doesn't get user/group info for Windows files

  - by Gnustavo

  I'm trying to get information about storage consumption from NetBackup's bplist output. I'm running NBU 6.0MP5 on a RHEL 3 server. The server is backing up several Solaris, Linux, and Windows machines. When I use bplist to get information about files backed up on any UNIX machine I get something like this: # bplist -C unixclient -R 99 -l -s 01/28/2006 -e 01/29/2006 / drwxr-xr-x test ccase 0 Nov 16 09:28 /l/home2/test/ -rw------- test ccase 4737 Jan 06 17:54 /l/home2/test/.bash_history -rw-rw-r-- test ccase 104 Nov 11 2004 /l/home2/test/.bashrc However, when I use it to list files backed up on any Windows client I can't get the user and group information. They both always appear as 'root'. Like this: # bplist -C winclient -t 13 -R 99 -l -s 02/20/2006 / drwx------ root root 0 Feb 20 14:26 /C/temp/ -rwx------ root root 41 Feb 20 14:26 /C/temp/asdf.txt drwx------ root root 0 May 25 2004 /C/temp/CTRMNGR/ Does anyone know why bplist doesn't show the correct user/group for Windows files? If it can't, is there a way to get that information using another command? Thanks. Gustavo.

  Read the article

• SQLSTATE[HY000]: General error: 2006 MySQL server has gone away

  - by Barkat Ullah

  Server details: RAM: 16GB HDD: 1000GB OS: Linux 2.6.32-220.7.1.el6.x86_64 Processor: 6 Core Please see the link below for my # top preview: I can often see the error mentioned in title in my plesk panel and my /etc/my.cnf configuration are as below: bind-address=127.0.0.1 local-infile=0 datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock user=mysql max_connections=20000 max_user_connections=20000 key_buffer_size=512M join_buffer_size=4M read_buffer_size=4M read_rnd_buffer_size=512M sort_buffer_size=8M wait_timeout=300 interactive_timeout=300 connect_timeout=300 tmp_table_size=8M thread_concurrency=12 concurrent_insert=2 query_cache_limit=64M query_cache_size=128M query_cache_type=2 transaction_alloc_block_size=8192 max_allowed_packet=512M [mysqldump] quick max_allowed_packet=512M [myisamchk] key_buffer_size=128M sort_buffer_size=128M read_buffer_size=32M write_buffer_size=32M [mysqlhotcopy] interactive-timeout [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid open_files_limit=8192 As my server httpd conf is set to /etc/httpd/conf.d/swtune.conf and the configuration is as below: at prefork.c: <IfModule prefork.c> StartServers 8 MinSpareServers 10 MaxSpareServers 20 ServerLimit 1536 MaxClients 1536 MaxRequestsPerChild 4000 </IfModule> If I run grep -i maxclient /var/log/httpd/error_log then I can see everyday this error: [root@u16170254 ~]# grep -i maxclient /var/log/httpd/error_log [Sun Apr 15 07:26:03 2012] [error] server reached MaxClients setting, consider raising the MaxClients setting [Mon Apr 16 06:09:22 2012] [error] server reached MaxClients setting, consider raising the MaxClients setting I tried to explain everything that I changed to keep my server okay, but maximum time my server is down. Please help me which parameter can I change to keep my server okay and my sites can load fast. It is taking too much time to load my sites.

  Read the article

• Change Windows Authentication user for Sql Server Management Studio

  - by Asmor

  We're using Sql Server 2005 with Windows Authentication setup. So normally, when you log in using e.g. Sql Server Management Studio, it forces you to log in at MACHINE_NAME\Username. Anyways, on this one particular computer, the person said they had to make a new account called User01 to do something and showed me where she'd created it under security in the "master" system database. And so now when she logs in, it's listed as MACHINE_NAME\User01 (not the actual Windows user name). It's still set to Windows Authentication, though, and I'm unable to change the login name. Now here's where the real problem comes in... I didn't realize that she was being logged in under this user name at the time, and I disabled it to see what would happen. Now I can't log into the server under her account. I created a new account in Windows called test, and as expected SSMS had the username as MACHINE_NAME\test, and I was able to log in fine. However, the area where the User01 account was listed is not visible to me as far as I can tell and so I can't reenable it. I also tried running the following query: alter login User01 ENABLE And got this error: Msg 15151, Level 16, State 1, Line 1 Cannot alter the login 'User01', because it does not exist or you do not have permission. So in a nutshell, ideally I'd like to reenable User01 somehow, just to get things back to where they used to be. Failing that, how can I force SSMS to log in using the Windows account name as it should be, rather than trying to use User01?

  Read the article

• wget recursively download from pages with lots of links

  - by Shadow

  When using wget with the recursive option turned on I am getting an error message when it is trying to download a file. It thinks the link is a downloadable file when in reality it should just be following it to get to the page that actually contains the files(or more links to follow) that I want. wget -r -l 16 --accept=jpg website.com The error message is: .... since it should be rejected. This usually occurs when the website link it is trying to fetch ends with a sql statement. The problem however doesn't occur when using the very same wget command on that link. I want to know how exactly it is trying to fetch the pages. I guess I could always take a poke around the source although I don't know how messy the project is. I might also be missing exactly what "recursive" means in the context of wget. I thought it would run through and travel in each link getting the files with the extension I have requested. I posted this up over at stackOverFlow but they turned me over here:) Hoping you guys can help.

  Read the article

< Previous Page | 376 377 378 379 380 381 382 383 384 385 386 387  | Next Page >