Search Results

Search found 40602 results on 1625 pages for 'event based components'.

Page 607/1625 | < Previous Page | 603 604 605 606 607 608 609 610 611 612 613 614  | Next Page >

• ESXI 5.1 - Unable to trunk to cisco switch

  - by Lance

  I have configured my esxi host vSwitch1 to use the secondary NIC on my VMware host. On vSwitch1 configuration I have set the VLAN to 4095 which specifies to allow all VLANs. If my cisco switch port configuration is set to an access port my server can ping the vlan interface on the switch. If my cisco switch port configuration is set to a trunk, whilst it stays UP UP and CDP information is available, I lose my ping from VMware VM server to the local vlan interface on the switch and I lose any server connectivity to my network. Switch NIC teaming policy to Route based on originating virtual port ID Configuration based on: http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=1006628 interface GigabitEthernet0/42 description Host Port switchport trunk encapsulation dot1q switchport trunk allowed vlan 18,220 switchport mode trunk switchport nonegotiate spanning-tree portfast trunk end Output from ESXI CLI esxcfg-vswitch -l: ~ # esxcfg-vswitch -l Switch Name Num Ports Used Ports Configured Ports MTU Uplinks vSwitch0 128 5 128 1500 vmnic0 PortGroup Name VLAN ID Used Ports Uplinks VM Network 4095 1 vmnic0 Management Network 4095 1 vmnic0 Switch Name Num Ports Used Ports Configured Ports MTU Uplinks vSwitch1 128 4 128 1500 vmnic1 PortGroup Name VLAN ID Used Ports Uplinks VM Network 2 4095 1 vmnic1 Any tips welcome!!!

  Read the article

• iSCSI, failover and XenServer

  - by jemmille

  I have an iSCSI fail over implementation setup so if one of my storage units fails the other takes over immediately (it also runs the NFS shares). When fail over occurs, volumes are exported, the IP is switched to the other machine and the targets are reconfigured. The fail over of the storage system itself works just fine. I use NexentaStor for my filer. When I do a test (manual) fail over of my storage the following occurs: Note: I run the admin VM's on NFS and customer based VM's on iSCSI All NFS based VM's remain up and working perfectly through the failover and after All VM 's running on iSCSI eventually report the following: An error about not being able to write to a particular block An error about journaling not working Then the file system goes RO To get the VM's working again I have to do the following: Force shutdown of the "broken" VM's. Detach the iSCSI SR Re-attach the iSCSI SR Boot the VM on a different server (5 in my pool) If I don't boot on a different server I get this error "Internal error: Failure("The VDI <uuid&gt; is already attached in RW mode; it can't be attached in RO mode!")" The only way I have found to fix that error is to reboot the entire server it was running on previously which is obviously a huge pain. Currently multipathing is NOT enabled (but can be and the same thing still occurs). I have edited much of the /etc/iscsid.conf file to work with the timeout settings but to no avail. In short, my storage fails over properly but XenServer does not keep the connection alive. As a thought, the error that shows up in #4 above might be the ultimate cause and fixing that would fix everything? Any help would be appreciated more than you know.

  Read the article

• MySQL replication - rapidly growing relay bin logs

  - by Rob Forrest

  Morning all, I've got a really strange situation here this morning much like a reportedly fixed MySQL bug. http://bugs.mysql.com/bug.php?id=28421 My relay bin logs are rapidly filling with an infinite loop of junk made of this sort of thing. #121018 5:40:04 server id 101 end_log_pos 15598207 #Append_block: file_id: 2244 block_len: 8192 # at 15598352 #121018 5:40:04 server id 101 end_log_pos 15606422 #Append_block: file_id: 2244 block_len: 8192 # at 15606567 ... # at 7163731 #121018 5:38:39 server id 101 end_log_pos 7171801 #Append_block: file_id: 2243 block_len: 8192 WARNING: Ignoring Append_block as there is no Create_file event for file_id: 2243 # at 7171946 #121018 5:38:39 server id 101 end_log_pos 7180016 #Append_block: file_id: 2243 block_len: 8192 WARNING: Ignoring Append_block as there is no Create_file event for file_id: 2243 These log files grow to 1Gb within about a minute before rotating and starting again. These big files are interspersed with 1 or 2 smaller files with just this in /*!40019 SET @@session.max_insert_delayed_threads=0*/; /*!50003 SET @OLD_COMPLETION_TYPE=@@COMPLETION_TYPE,COMPLETION_TYPE=0*/; DELIMITER /*!*/; # at 4 #121023 9:43:05 server id 100 end_log_pos 106 Start: binlog v 4, server v 5.1.61-log created 121023 9:43:05 BINLOG ' mViGUA9kAAAAZgAAAGoAAAAAAAQANS4xLjYxLWxvZwAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAEzgNAAgAEgAEBAQEEgAAUwAEGggAAAAICAgC '/*!*/; # at 106 #121023 9:43:05 server id 100 end_log_pos 156 Rotate to mysqld-relay-bin.000003 pos: 4 DELIMITER ; # End of log file ROLLBACK /* added by mysqlbinlog */; /*!50003 SET COMPLETION_TYPE=@OLD_COMPLETION_TYPE*/; We're running a master-master replication setup with the problematic server running mysql 5.1.61. The other server which is, for the moment, stable is running 5.1.58. Has anyone got any ideas what the solution is to this and moreover, what might have caused this?

  Read the article

• Centralized Windows/Mac Patch Management that is easy to use

  - by BiggsTRC

  I'm looking for advice on what patch management solutions you would recommend based upon your experience. I'm also looking for which ones you would not recommend based upon your experience. We have a mixed network of Windows and Mac clients. Our central servers are all Windows servers, although I have considered putting in a Mac server to better handle our Mac clients. The issue we are facing currently is that we need to maintain the patches on all of our third-party applications. Right now we use WSUS, which handles with patching of Windows and some Microsoft products but that is about it. I need something to cover the other applications, specifically things like Adobe products (Reader, Flash, Dreamweaver, etc.) Our network isn't that big (maybe 200 clients) and I don't have a person to dedicate just to patching and maintaining a patch management solution. Thus very large and complicated solutions like System Center are most likely out. I have recently been looking at Dell's Kace K1000 solution (http://www.kace.com/products/systems-management-appliance/). It seems simple and it provides a lot of tools in one package that I would like/need as well. I like the fact that it is self-contained in an appliance and that it is designed for solutions like mine. However, I'm not sure if this is the best solution. I've also looked some at Shavlik's Netchk solution (http://www.shavlik.com/netchk-protect.aspx) but I don't need an anti-virus product. However, it looks like they might have a very good patch database. My question is this: What are your thoughts on these to products? Are there better products out there? Are there issues that I'm not considering? I want something that is very good at patching a broad range of products, that is simple to use, that takes a minimal amount of management (like WSUS), and that (hopefully) works with Mac and Windows.

  Read the article

• Wireless disconnect randomly with wpa_supplicant reason=2

  - by renenglish

  I installed ubuntu-server 12.04 on my PC , and I use an usb wireless card to join the network. It works ok when I boot up my PC , but the wireless disconnects after a while. I pkill wpa_supplicant and reload the driver rtl8192cu , then it works a again. Then it disconnect again after about a random minutes. Here is the syslog: 22384 May 29 21:49:27 homecenter kernel: [ 6450.459313] wlan1: authenticated 22385 May 29 21:49:27 homecenter kernel: [ 6450.459535] wlan1: associate with f4:ec:38:45:62:74 (try 1) 22386 May 29 21:49:27 homecenter kernel: [ 6450.469080] wlan1: RX AssocResp from f4:ec:38:45:62:74 (capab=0 x431 status=0 aid=3) 22387 May 29 21:49:27 homecenter kernel: [ 6450.469085] wlan1: associated 22388 May 29 21:49:27 homecenter wpa_supplicant[2342]: Associated with f4:ec:38:45:62:74 22389 May 29 21:49:27 homecenter kernel: [ 6450.481933] ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready 22390 May 29 21:49:27 homecenter wpa_supplicant[2342]: WPA: Key negotiation completed with f4:ec:38:45:62:7 4 [PTK=CCMP GTK=CCMP] 22391 May 29 21:49:27 homecenter wpa_supplicant[2342]: CTRL-EVENT-CONNECTED - Connection to f4:ec:38:45:62: 74 completed (auth) [id=0 id_str=] 22392 May 29 21:49:38 homecenter kernel: [ 6461.472014] wlan1: no IPv6 routers present 22393 May 29 21:49:38 homecenter ntpdate[2263]: step time server 91.189.94.4 offset 0.012758 sec 22394 May 29 21:49:51 homecenter ntpdate[2404]: step time server 91.189.94.4 offset -0.001190 sec 22395 May 29 21:54:38 homecenter kernel: [ 6762.052030] wlan1: deauthenticated from f4:ec:38:45:62:74 (Reas on: 2) 22396 May 29 21:54:38 homecenter wpa_supplicant[2342]: CTRL-EVENT-DISCONNECTED bssid=f4:ec:38:45:62:74 reas on=2 22397 May 29 21:54:38 homecenter kernel: [ 6762.064744] cfg80211: All devices are disconnected, going to re store regulatory settings 22398 May 29 21:54:38 homecenter kernel: [ 6762.064752] cfg80211: Restoring regulatory settings 22399 May 29 21:54:38 homecenter kernel: [ 6762.064757] cfg80211: Calling CRDA to update world regulatory d omain 22400 May 29 21:54:38 homecenter kernel: [ 6762.069938] cfg80211: Ignoring regulatory request Set by core s ince the driver uses its own custom regulatory domain 22401 May 29 21:54:38 homecenter kernel: [ 6762.069943] cfg80211: World regulatory domain updated: 22402 May 29 21:54:38 homecenter kernel: [ 6762.069945] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) 22403 May 29 21:54:38 homecenter kernel: [ 6762.069949] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KH z), (300 mBi, 2000 mBm) 22404 May 29 21:54:38 homecenter kernel: [ 6762.069952] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KH z), (300 mBi, 2000 mBm) 22405 May 29 21:54:38 homecenter kernel: [ 6762.069956] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KH z), (300 mBi, 2000 mBm) 22406 May 29 21:54:38 homecenter kernel: [ 6762.069959] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KH z), (300 mBi, 2000 mBm) 22407 May 29 21:54:38 homecenter kernel: [ 6762.069962] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KH z), (300 mBi, 2000 mBm)

  Read the article

• System Idle Process network traffic?-Updated

  - by Moab

  I was using NetBalancer and noticed network traffic on an unidentified service, but when I highlight it and then go to the lower center pane and click the parent process it says it is the System Idle process, it is showing incoming and outgoing traffic in the upper pane, anyone know why this Windows System Idle Process is talking on the network? Windows 7 HP 64bit . . . Edit, after blocking the traffic for that unidentified Service I checked my event viewer (Windows LogsSystem) and found 3 new events that were never recorded before and matched the time I blocked the traffic. So is this part of the Windows local DNS cache? Event ID 1014 DNS Client Events Name resolution for the name dns.msftncsi.com timed out after none of the configured DNS servers responded. dns.msftncsi.com Name resolution for the name wpad.home timed out after none of the configured DNS servers responded. wpad Name resolution for the name mscrl.microsoft.com timed out after none of the configured DNS servers responded. mscrl.microsoft.com . Then My Web Browser refused to work, I re-enabled the traffic and all returned to normal. .

  Read the article

• Is one server on a vlan unnecessary?

  - by moomoochoo

  DETAILS I've been researching web hosting solutions in Japan. Based on this question one of the services available seems to be a VLAN. I've read about the advantages of such a system for a large organization, but there doesn't seem to be much information regarding smaller setups. I take that to mean that for one server it is likely to be unnecessary? My concern is that I don't know how many other servers are on the WAN, so regardless of how many servers I use a VLAN might still be a good idea. SERVER INFO One dedicated server would be used. It would not be virtualized. My Research so far Based on comments here, a VLAN would be useful for mitigating these problems. A user on another server could, either mistakenly or maliciously, assign one of your IP addresses to their server, resulting in a "duplicate IP" situation that would cause connectivity issues. A user on another server could poison the arp cache and potentially redirect traffic to snoop on communication intended to/from your server. (later in the discussion this point was said to be unrealistic.) QUESTION Is it worthwhile getting a vlan for one dedicated server? Will it be easier/the same/ harder to manage?

  Read the article

• Makecert.exe hangs

  - by Robert

  I was following the steps in Scott Hanselman's blog post describing how to create a certificate authority and code signing certificate for PowerShell scripts. Initially, I created the certificate authority and a personal certifcate and used it to sign a powershell script successfully. All went as described in the blog post. The problem starts (as most do) when I did something that was (probably) stupid, although it seemed reasonable at the time. I wanted to start over and repeat the process again with a clean slate, so from the mmc certificates snap-in console, I deleted the personal certificate and the certificate authority I created previously. After that any time I try to use makecert, (just as I did the first time around), makecert either hangs or faults (which prompts to end or debug). Did I hose something up by deleting via the certificates snap-in? It didn't complain or warn me that it could be potentially hazardous. Is this just coincidence and something else entirely could be hosed? I have Event Log entries from the times when makecert crashed, which all look very similar; here is one: Log Name: Application Source: Application Error Date: 8/5/2009 3:55:04 PM Event ID: 1000 Task Category: (100) Level: Error Description: Faulting application makecert.exe, version 6.0.6000.16384, time stamp 0x4545910b, faulting module ntdll.dll, version 6.0.6002.18005, time stamp 0x49e03821, exception code 0xc0000005, fault offset 0x00067409, process id 0xe58, application start time 0x01ca160efdf30625. Anyone have any ideas as to what exactly caused this and/or what I can do to fix it. I'm on 32-bit Vista Enterprise w/SP2.

  Read the article

• How to direct reverse proxy requests using wildcard vhosts

  - by HonoredMule

  I'm interested in running a reverse proxy with 2-3 virtual machines behind it. Each internal server will run multiple virtual hosts, and rather than manually configuring each individual vhost on the proxy (a variety of vhosts come and go too often for this to be practical), I would like to use something which can employ pattern matching in a sequential order to find the appropriate back-end server. For example: Server 1: *.dev.mysite.com Server 2: *.stage.mysite.com Server 3: *.mysite.com, dev.mysite.com, stage.mysite.com, mysite.com Server 4: * In the above configuration, task.dev.mysite.com would go to Server 1, dev.mysite.com would go to Server 3, yoursite.stage.mysite.com to Server 2, www.mysite.com to Server 3, and yoursite.com to Server 4. I've looked into using Squid, Varnish, and nginx so far. I have my opinions regarding their respective desirability and general suitability, but it's not readily apparent if any of them can handle dynamic server selection in this manner and not require per-vhost configuration. Apache on the other hand can do this handily and simply, but otherwise (aside from being well-known and familiar) seems very poorly suited to the partly-performance-serving task. Performance isn't actually a major concern yet, but it seems foolish to use Apache if another system will perform far better and can also handle the desired 'hands-free' configuration. But so is frequently having to adjust the gateway for all production services and risk network-wide outage...and so also is setting oneself up for longer downtime later if Apache becomes a too-small bottleneck. Which of these (or other) reverse proxies can do it/would do it best? And maybe I should post this as a separate question, but if Apache is the only practical option, how safe/reliable/predictable is apache-mpm-event in apache2.2 (Ubuntu 12.04.1) particularly for a dedicated reverse proxy? As I understand it the Event MPM was declared "safe" as of 2.4 but it's unclear whether reaching stability in 2.4 has any implications for the older (2.2) versions available in official/stable package channels of various distros.

  Read the article

• CheckPoint/Amazon VPC VPN tunnel working inconsistently

  - by Lee

  First time poster, so please be gentle and correct me if there's Server Fault etiquette I'm missing. We have two CheckPoint edge devices at sites A & B, independently managed, connecting to two Amazon private clouds. In both cases, the two Amazon VPCs are in the same community on the CheckPoint device. A VPN tunnel exists between the two CheckPoint devices as well. Between Sites A & B and the Amazon VPC in Northern Virigina, we are unable to keep more than one tunnel up. Both will come up, but tunnel 2 will drop an hour after initiation and will not come back up while tunnel 1 is up. We believe the 1-hour period is due to IPsec phase 2 renegotiation, but can't be sure. On our side, we see the tunnel 2 remote endpoint as not responding to phase 2 negotiation. Between Sites A & B and the Amazon VPC in Oregon, we have no issues. Both tunnels are up and fail over properly. The CheckPoint gateways are using domain-based VPNs. According to CheckPoint's advice to Amazon, this won't work. Yet, in Oregon, it does. We've pursued this with Amazon and, despite the fact it's working in Oregon, they've refused to troubleshoot with us further. Can anyone suggest anything we can do to try to get this stabilized? Going to route-based VPNs is not an option for us.

  Read the article

• SQLVDI error - attempt to release mutex not owned by caller

  - by Chris W

  I've started getting some errors in the App event log of one of our database servers (Windows 2003 & SQL Server 2005). The nightly full database backups are completing successfully however immediately after the job success is written to the event log there is a run of entries that say: SQLVDI: Loc=CVDS. Desc=Release(ClientAliveMutex). ErrorCode=(288)Attempt to release mutex not owned by caller. There's five of these logged - the server itself has more than 20 databases on it which are all backed up successfully. The server is backed up by Bacula using a VSS backup. Has anyone got any ideas what would be causing the errors? They seem to have started after a re-boot on Friday to install some patches which included KB960089. Edit: After getting the errors for a few days they've now stopped without any action on my part other than letting the backups continue as they were. It may be a coincidence but they stopped after Bacula completed its weekly full rather than the daily incremental backup.

  Read the article

• SQLVDI error - attempt to release mutex not owned by caller

  - by Chris W

  I've started getting some errors in the App event log of one of our database servers (Windows 2003 & SQL Server 2005). The nightly full database backups are completing successfully however immediately after the job success is written to the event log there is a run of entries that say: SQLVDI: Loc=CVDS. Desc=Release(ClientAliveMutex). ErrorCode=(288)Attempt to release mutex not owned by caller. There's five of these logged - the server itself has more than 20 databases on it which are all backed up successfully. The server is backed up by Bacula using a VSS backup. Has anyone got any ideas what would be causing the errors? They seem to have started after a re-boot on Friday to install some patches which included KB960089. Edit: After getting the errors for a few days they've now stopped without any action on my part other than letting the backups continue as they were. It may be a coincidence but they stopped after Bacula completed its weekly full rather than the daily incremental backup.

  Read the article

• Apache no longer starts at Windows boot up

  - by w3d

  I have Apache installed as part of XAMPP - local test server. It is configured as a Windows (XP) Service. Startup type is "Automatic". For a long time now it has always started when Windows boots up, but recently this has stopped happening. I now need to start it manually via the XAMPP Control Panel - at which point it appears to start up perfectly OK. The only recent updates to the machine (that I recall) are Windows Updates - none of which appear to have "known issues" that relate to this. And updates to Google Chrome. Any ideas what could prevent Apache from starting automatically at Windows (XP) boot up? EDIT#1 There are 2 related Errors in my system event log regarding the Service Control Manager: Timeout (30000 milliseconds) waiting for the Apache2.2 service to connect. The Apache2.2 service failed to start due to the following error: The service did not respond to the start or control request in a timely fashion. When I manually start the Apache server after boot up there are 2 "information" events stating that it was "sent a start control" and that it "entered the running state". Although I notice it appears to take 19 seconds between the start control being sent and entering a running state - according to the event log. So, maybe 30 seconds during boot up isn't long enough (anymore) for Apache to start??

  Read the article

• How to get an ARM CPU clock speed in Linux?

  - by MiKy

  I have an ARM-based embedded machine based on S3C2416 board. According to the specifications I have available there should be a 533 MHz ARM9 (ARM926EJ-S according to /proc/cpuinfo), however the software running on it "feels" slow, compared to the same software on my Android phone with a 528MHz ARM CPU. /proc/cpuinfo tells me that BogoMIPS is 266.24. I know that I should not trust BogoMIPS regarding performance ("Bogo" = bogus), however I would like to get a measurement on the actual CPU speed. On x86, I could use the rdtsc instruction to get the time stamp counter, wait a second (sleep(1)), read the counter again to get an approximation on the CPU speed, and according to my experience, this value was close enough to the real CPU speed. How can I find the actual CPU speed of given ARM processor? Update I found this simple Pi calculator, which I compiled both for my Android phone and the ARM board. The results are as follows: S3C2416 # cat /proc/cpuinfo Processor : ARM926EJ-S rev 5 (v5l) BogoMIPS : 266.24 Features : swp half fastmult edsp java ... #./pi_arm 10000 Calculation of PI using FFT and AGM, ver. LG1.1.2-MP1.5.2a.memsave ... 8.50 sec. (real time) Android # cat /proc/cpuinfo Processor : ARMv6-compatible processor rev 2 (v6l) BogoMIPS : 527.56 Features : swp half thumb fastmult edsp java # ./pi_android 10000 Calculation of PI using FFT and AGM, ver. LG1.1.2-MP1.5.2a.memsave ... 5.95 sec. (real time) So it seems that the ARM926EJ-S is slower than my Android phone, but not twice slower as I would expect by the BogoMIPS figures. I am still unsure about the clock speed of the ARM9 CPU.

  Read the article

• 0 connected nodes in datastax opscenter

  - by gansbrest

  Installed opscenterd on the separate node outside of the cluster, but within firewall ( aws security group ). Tested all possible ports between agents and opcenter server. No errors in the log.. 2013-10-30 01:07:23+0000 [FC_Cluster] INFO: Initializing event storage. 2013-10-30 01:07:23+0000 [FC_Cluster] INFO: Attempting to load all persisted alert rules 2013-10-30 01:07:23+0000 [FC_Cluster] INFO: Done loading persisted alert rules 2013-10-30 01:07:23+0000 [FC_Cluster] INFO: Done initializing event storage. 2013-10-30 01:07:23+0000 [FC_Cluster] INFO: Done loading persisted scheduled job descriptions 2013-10-30 01:07:23+0000 [FC_Cluster] INFO: OpsCenter starting up. 2013-10-30 01:07:23+0000 [] INFO: Finished starting new cluster services for FC_Cluster 2013-10-30 01:08:04+0000 [FC_Cluster] INFO: Agent for ip 10.34.10.185 is version u'3.2.2' 2013-10-30 01:08:04+0000 [FC_Cluster] INFO: Agent for ip 10.32.37.251 is version u'3.2.2' 2013-10-30 01:08:04+0000 [FC_Cluster] INFO: Agent for ip 10.82.226.252 is version u'3.2.2' The most interesting part that I can see some data in the opscenter UI, when I stop agents, there is no data displayed, when I start - it show up again, but at the same time it shows 0 connected nodes. Storage capacity is even funnier - 3 of 0 nodes.. Any ideas why that could be happening?

  Read the article

• Windows 2008 Standard upgrade to Windows 2008 Enterprise failure

  - by Archit Baweja

  Sidestory, I was in the process of setting up a second Exchange 2010 server for DAG support, when I realized that my box needed Windows 2008 Enterprise edition. The box currently has Windows 2008 Standard Windows update including SP2 Exchange 2010 with CAS, HT, Mailbox roles Domain Services role File Services role. When I try to upgrade to Windows 2008 Enterprise, I initially got a "your current version of windows is more recent than the intallation media", something to that effect. My first guess was it may be SP2 related, so I uninstalled SP2, restarted and tried again. This time it gave me an error to the effect Windows could not configure one or more windows components. Please restart and try the update again. This was at the last stage of the Windows 2008 Enterprise install when it says "Completing installation". So I removed Domain Services role (including demoting it as a DC). However I get the same error again. Anyone see something like this before and have any suggestions? Also , is there a log file the windows upgrade program spits out that I can consult to see what component exactly is interfering? Update 1 Based on some googling I finally found the setup log file, and it seems that Windows setup had an issue determining the .Net 3.0 "feature" being installed or uninstalled. So based of of a win7/vista technet article I'm going to retry the upgrade after removing the .Net 3.0 feature.

  Read the article

• VMware vSphere 4.1 and BackupExec 2010

  - by Josh

  I'm sure a common problem with most shops is backups, their size, and the window in which you have to back up the data. What we are working with: VMware vSphere 4.1 Cluster PS4000XV Equallogic Storage Array (1.6TB Volume dedicated for Backup to Disk) Physical Backup Server with a single LTO4 drive. BackupExec 2010 R3 with the following agents, Exchange, SQL, Active Directory, VMware. Dual Gigabit MPIO Connections between all devices (Storage Array, Backup Server, VM Hosts) What we would like to accomplish: I would like to implement an efficient Backup to Disk to Tape solution where all of our VMs are backed up to the Storage Array first, and then once completely backed up to the array are replicated to tape. In the event we needed to recover, we would be able to do so directly from tape. Where we are at currently. Of the several ways I have setup the jobs in Backup Exec 2010 R3 the backup jobs all queue up at the same time, as soon as a job is finished backing up to disk it then starts that same job to tape, but pulling from the original source instead of the designated B2D location. I understand that I could create a job that backs up the "Backup to Disk" folder to tape, but in the event of restoration, I would first need to stage the data in the B2D folder before I could restore the VM. I would really like to hear from individuals in similar situations. Any and all comments and critiques are appreciated.

  Read the article

• "The zone can be scavenged after" keeps incrementing

  - by kce

  What are you trying to do? I'm trying to enable DNS scavenging on a DNS zone that has about a hundred stale DNS records. What have you tried in order to make it happen? I setup DNS Scavenging per everyone's favorite TechNet Blog post: Don't be afraid of DNS Scavenging. Just be patient. I first disabled scavenging on all of our domain controllers: DNSCmd . /ZoneResetScavengeServers contoso.com 192.168.1.1 192.168.1.2 I then enabled automatic scavenging on the DNS zone: I then enabled DNS scavenging on one of the domain controllers: I then found a few records that I expected to get delete with timstamps from a few years ago and ensured that that the Delete this record when it becomes stale and that time stamp was actually set: Finally I reloaded the zone and waited 14 days (the sum of the Refresh + No-Refresh periods). What results did you expect? I expected to see a 2501 Event in the DNS server logs noting the deletion of a bunch of DNS records. What actually happened? Nothing happened. The Zone Aging/Scavenging Properties showed that the zone could be scavenged after 6/12/2014 10:00:00 AM last week. No 2501/2502 events were recorded. All of the records with "aged" time stamps are still present. The date at which the zone can be scavenged after incremented another seven days to ?6/?18/?2014 10:00:00 AM. As I understand it until that date stays at least 14 days in the past nothing will ever even be eligible for scavenging let alone actually be scavenged. The only 2501 events recorded in the event logs are ones that I have triggered by right clicking and selecting "Scavenge Stale Resource Records". They note that scavenging will try to run again in 168 hours which was this morning. I have DNS scavenging enabled for a few months and have waited patiently for something to happen. I have reloaded the zone multiple times (which resets this timestamp). What am I missing here?

  Read the article

• ISA 2006 SP1 - SSL Client Certificate Authentication in Workgroup Environment

  - by JoshODBrown

  We have an IIS6 website that was previously published using an ISA 2006 SP1 standard server publishing rule. In IIS we had required a client certificate be provided before the website could be accessed... this all worked fine and dandy. Now we wish to use a web publishing rule on ISA 2006 SP1 for this same website. However, it seems the client certificate doesn't get processed now, so of course the user can't access the website. I've read a few articles stating the CA for the certificate needs to be installed in the trusted root certificate authorities store on the ISA Server (i have done this), as well as installing the client certificate on the ISA Server (done as well). I have also verified that the ISA Server is able to access the CRL for our CA no problem... In the listener properties for the web publishing rule, under Authentication, and Client Authentication Method, there is an option for SSL Client Certificate Authentication... i select this, but it appears the only Authentication Validation Method selectable is Windows (Active Directory).... there is no Active Directory in this environment. When i configure the rule with the defaults, I then try to hit my website and it prompts for my certificate, i choose it and hit ok... then I'm given the following error Error Code: 500 Internal Server Error. The server denied the specified Uniform Resource Locator (URL). Contact the server administrator. (12202) I check the event logs on the ISA Server and in Security Logs, i see Event ID 536, Failure Aud. The reason: The NetLogon component is not active. I think this is pretty obvious since there is no active directory available. Is there a way to make this web publishing rule work using client certificates in this workgroup environment? Any suggestions or links to helpful documents would be greatly appreciated!

  Read the article

• Controller Error: Do I need to worry?

  - by Kryten

  Hi, I have a HP Pavillion dv5224ea Laptop with Windows 7 on it. Recently I discovered a Error in Event Viewer: The driver detected a controller error on \Device\Ide\IdePort1. (more details): - System - Provider [ Name] atapi - EventID 11 [ Qualifiers] 49156 Level 2 Task 0 Keywords 0x80000000000000 - TimeCreated [ SystemTime] 2010-03-07T12:43:07.090197600Z EventRecordID 30198 Channel System Computer Alistair-Win7 Security - EventData \Device\Ide\IdePort1 0000100001000000000000000B0004C002000000850100C00000000000000000000000000000000000000000000000000000000004100000 -------------------------------------------------------------------------------- Binary data: In Words 0000: 00100000 00000001 00000000 C004000B 0008: 00000002 C0000185 00000000 00000000 0010: 00000000 00000000 00000000 00000000 0018: 00000000 00001004 In Bytes 0000: 00 00 10 00 01 00 00 00 ........ 0008: 00 00 00 00 0B 00 04 C0 .......À 0010: 02 00 00 00 85 01 00 C0 ......À 0018: 00 00 00 00 00 00 00 00 ........ 0020: 00 00 00 00 00 00 00 00 ........ 0028: 00 00 00 00 00 00 00 00 ........ 0030: 00 00 00 00 04 10 00 00 ........ Event Viewer is recording A LOT of these errors (sometimes 13, one after the other!). Do I need to worry? What does this error mean? What device could "\Device\Ide\IdePort1" be? What is a ATAPI Error? Do I need to re-install Windows? I generally find the occurs when I try to backup my machine (using Windows Backup) or when using a program that uses Volume Shadow Copy. I have run "sfc", no problems. There are no Device Errors in Device Manager. I have also run "vssadmin list writers", no problems. Whats going on??? Would it be a good idea to re-install Windows 7?

  Read the article

• Windows 2008 RemoteAPP client disconnects within a matter of minutes.

  - by Jeroen Wilke

  I'm having an odd problem with Windows 2008 TS, and remote applications specifically. The situation is as follows: TS idle timeout is disabled via GPO TS terminating disconnected sessions after 1hr (via GPO) My users can log on to the Terminal server, and get a full desktop, OR via rdp files that give access to a few remote applications. When a user connects to a full desktop, everything is fine and dandy, they will remain logged on indefinately, and when they disconnect the session is terminated after an hour. however, when a user connects using a remote application link, the client seems to disconnect after only a few minutes of inactivity, when you click the window, the session reconnects. EventID's on TS server: 4779: This event is generated when a user disconnects from an existing Terminal Services session, or when a user switches away from an existing destop using Fast User Switching. 4778 : This event is generated when a user reconnects to an existing Terminal Services session, or when a user switches to an existing desktop using Fast User Switching users are connecting directly to 3389, not using a TS-gateway at the moment. This behavior is consistent on different clients that we have, Full desktop is fine, RemoteAPP constantly disconnects. The .rdp file used doesn't list any interesting parameters, aside from what application to launch, and where to find it. Can someone explain to me how there can be a difference in behaviour between full desktop, and remoteapp ? since essentially they use the exact same client ? Regards Jeroen

  Read the article

• cPanel web server redundancy advice?

  - by crgnz

  At present I operate a (reasonably low volume) web-hosting service with a Centos 5.3 server running cPanel/WHM. I would like to implement a level of redundancy such that in the event of server failure, I can restore service with a minimum of effort in less than 60 minutes. I also want to setup a secondary DNS that cPanel will replicate with. My current idea is to kill two birds with one stone by: My current server is called "www1" Purchase an identical server (HP DL360 G4) with mirrored disks. Call this server "www2" Install Centos 5.4 (or perhaps I should install 5.3 to be identical with www1) Install cPanel/WHM on this server and fully license it Setup www1 and www2 cPanel to replicate DNS with each other Setup a nightly replication script that does the following: a) rsync's the /home directory from www1 to www2 b) dumps all MySQL databases on www1 and copies them to a temp folder (with root access only) on www2 c) triggers a script to run on www2 that restores the MySQL dumps Thus each night a fully working copy of all the websites and MySQL databases is copied to www2. I do not have enough knowledge of MySQL replication to understand if it works safely and transparently with cPanel. Thus I propose the mysql dump/copy/restore due to not knowing any better! In the event that www1 dies a horrible death, I envisage that I could login to www2, change the IP addresses to those that www1 had, and presto, the websites are available again. The advantage of this idea is that it is fairly simple and "low tech" and thus does not require an expert sysadmin to setup and monitor (I am NOT an expert sysadmin) The disadvantage of this idea is that up to a full days worth of data changes would be lost. I think this would be acceptable to the sorts of customers I host at the moment. The other disadvantage would be having to pay for a full cPanel license, but I am comfortable with that cost, so for now all I want to discuss are technical considerations. Is this a sound scheme?

  Read the article

• Ho can I recover from SharePoint configuration errors after promoting the server to a Domain Controller?

  - by jjr2527

  I have a SharePoint 2010 VM setup in VirtualBox and I was using local machine accounts to handle security on the server. While preparing for a demo it came time to have some meaningful users on my VM image. I followed some docs on promoting my server to a Domain Controller in a new forrest. So now I have [MachineName].SPDEMO.CONTOSO.com and I can add users as needed. However, when I try to connect to my SharePoint sites I am getting a white screen with the error: "Cannot connect to the configuration database" I changed the pool identity account of each of my IIS app pools to the new Administrator account and started the services successfully but I can't get the SQL services to start up. When I try to start them I get the following error: Windows could not start the SQL Server (MSSQLSERVER) on Local Computer. For more information, review the System Event Log. If this is a non-Microsoft service, contact the service vendor, and refer to service-specific error code 17058. In the event log I see the following error: The SQL Server (MSSQLSERVER) service terminated with service-specific error %%17058. Can I recover from this or should I roll back or just uninstall the Domain Controller role. I'd like to keep the server as a standalone DC so I can do some user profile creation/management but I need the SharePoint bits to work as well.

  Read the article

• Firebird database corruption causes

  - by Rytis

  I am running several different Firebird versions (2.0, 2.1) on multiple entry level Windows-based servers with wildly varying hardware. The only matching thing between them is that they are running same home built application with the same database structure. Lately I've been seeing massive slowdowns on multiple servers. Turns out that database gets corrupted, so each time it breaks, I get to mend, backup and restore the database, and it all is fine for some time (1-2 weeks), and then it repeats once again. Thankfully, I haven't seen any data loss or damage... yet. The thing is that every such downtime results in lost productivity, and often quite some driving for me as some of the databases are in remote locations. I've been trying to find out what's causing the corruption, but I haven't been able to. The fact that it's running on different hardware hints that it should not be a hardware based problem. If we rule out hardware issues, I have a bad feeling that it's a bug in Firebird as I'm not doing anything fancy via SQL. Do you have any idea how to find out exactly what's causing the corruption and hopefully fix the problem?

  Read the article

• Blue screen issue

  - by Jack

  I received several BSOD's that are recorded in the following logs: Problem signature: Problem Event Name: BlueScreen OS Version: 6.1.7601.2.1.0.256.48 Locale ID: 3081 Additional information about the problem: BCCode: 50 BCP1: FFFFF95FF8150C10 BCP2: 0000000000000008 BCP3: FFFFF95FF8150C10 BCP4: 0000000000000005 OS Version: 6_1_7601 Service Pack: 1_0 Product: 256_1 Files that help describe the problem: C:\Windows\Minidump\040412-20030-01.dmp C:\Users\Jack\AppData\Local\Temp\WER-33025-0.sysdata.xml ~~~~~ Problem signature: Problem Event Name: BlueScreen OS Version: 6.1.7601.2.1.0.256.48 Locale ID: 3081 Additional information about the problem: BCCode: 1e BCP1: 0000000000000000 BCP2: 0000000000000000 BCP3: 0000000000000000 BCP4: 0000000000000000 OS Version: 6_1_7601 Service Pack: 1_0 Product: 256_1 Files that help describe the problem: C:\Windows\Minidump\040412-32729-01.dmp C:\Users\Jack\AppData\Local\Temp\WER-64319-0.sysdata.xml It seems to occur at random. I have gone 2 months without a BSOD, then I have gone a week with 10+ without changing what I am doing. This is my system: Windows 7 Professional 64-bit Gigabyte GA-890GPA-UD3H AMD Phenom II x6 1090T Processor 3.2GHz 8GB Ram(4X 2GB) Radeon HD 7850 2TB HDD Thermaltake 500W PSU I'm not sure about what the BSOD says, it just counts to 100 by 5's then restarts the computer. It happens fast and I have tried to get a picture before but to no avail.

  Read the article

< Previous Page | 603 604 605 606 607 608 609 610 611 612 613 614  | Next Page >