Search Results

Search found 13033 results on 522 pages for '12 04'.

Page 382/522 | < Previous Page | 378 379 380 381 382 383 384 385 386 387 388 389  | Next Page >

• Finding cause of TCP retransmission within a LAN

  - by Surreal

  Hello denizens of Server Fault I have an irritating problem with a LAN of about 100 computers, 2 Windows domain servers, and 12 VoIP phones. Since their installation around a year ago, every week or so, we notice a VoIP phone resetting itself - occasionally in the middle of a call. Simultaneously there are often signs of temporary loss of connection on computers: freezes in explorer while accessing network shares, errors in our administration software due to loss of connection to the database server. I have been doing some Wireshark monitoring on the connection between the VoIP PBX and the rest of the network. Wireshark picks up a clump of retransmitted TCP packets at the times when we record phone restarts. The Wireshark log shows about 2 clusters of retransmissions a day ranging from 5 packets to hundreds. Those in each cluster are mainly between the PBX and some set of the VoIP phones, but not always the same set. Often retransmissions at the same time are to phones connected to the same switch, but sometimes retransmissions occur together to phones at opposite ends of the network. There are usually some coincident retransmissions in passing TCP traffic, for example between client machines and the file servers. The spikes in retransmissions and phone resets do not correlate well with when the network is heavily loaded. They seem to occur slightly more during the day, but most in the evening, when traffic should be decreasing. They occur reasonably often late at night when most computers are turned off and traffic should be lowest. Do you have any ideas that might help diagnose the cause of problems like this? One thing I have not yet tried, but should have, is updating the firmware of all the switches.

  Read the article

• FreeBSD slow transfers - RFC 1323 scaling issue?

  - by Trey

  I think I may be having an issue with window scaling (RFC 1323) and am hoping that someone can enlighten me on what's going on. Server: FreeBSD 9, apache22, serving a static 100MB zip file. 192.168.18.30 Client: Mac OS X 10.6, Firefox 192.168.17.47 Network: Only a switch between them - the subnet is 192.168.16/22 (In this test, I also have dummynet filtering simulating an 80ms ping time on all IP traffic. I've seen nearly identical traces with a "real" setup, with real internet traffic/latency also) Questions: Does this look normal? Is packet #2 specifying a window size of 65535 and a scale of 512? Is packet #5 then shrinking the window size so it can use the 512 scale and still keep the overall calculated window size near 64K? Why is the window scale so high? Here are the first 6 packets from wireshark. For packets 5 and 6 I've included the details showing the window size and scaling factor being used for the data transfer. Code: No. Time Source Destination Protocol Length Info 108 6.699922 192.168.17.47 192.168.18.30 TCP 78 49190 http [SYN] Seq=0 Win=65535 Len=0 MSS=1460 WS=8 TSval=945617489 TSecr=0 SACK_PERM=1 115 6.781971 192.168.18.30 192.168.17.47 TCP 74 http 49190 [SYN, ACK] Seq=0 Ack=1 Win=65535 Len=0 MSS=1460 WS=512 SACK_PERM=1 TSval=2617517338 TSecr=945617489 116 6.782218 192.168.17.47 192.168.18.30 TCP 66 49190 http [ACK] Seq=1 Ack=1 Win=524280 Len=0 TSval=945617490 TSecr=2617517338 117 6.782220 192.168.17.47 192.168.18.30 HTTP 490 GET /utils/speedtest/large.file.zip HTTP/1.1 118 6.867070 192.168.18.30 192.168.17.47 TCP 375 [TCP segment of a reassembled PDU] Details: Transmission Control Protocol, Src Port: http (80), Dst Port: 49190 (49190), Seq: 1, Ack: 425, Len: 309 Source port: http (80) Destination port: 49190 (49190) [Stream index: 4] Sequence number: 1 (relative sequence number) [Next sequence number: 310 (relative sequence number)] Acknowledgement number: 425 (relative ack number) Header length: 32 bytes Flags: 0x018 (PSH, ACK) Window size value: 130 [Calculated window size: 66560] [Window size scaling factor: 512] Checksum: 0xd182 [validation disabled] Options: (12 bytes) No-Operation (NOP) No-Operation (NOP) Timestamps: TSval 2617517423, TSecr 945617490 [SEQ/ACK analysis] TCP segment data (309 bytes) Note: originally posted http://forums.freebsd.org/showthread.php?t=32552

  Read the article

• HTB.init / tc behind NAT

  - by Ben K.

  I have an Ubuntu 10 box that I'm trying to set up as a bandwidth-shaping router. The machine has one WAN interface, eth0 and two LAN interfaces, eth1 and eth2. NAT is configured using MASQUERADE as described at InternetConnectionSharing. I'm mostly concerned with shaping outbound traffic from the LAN interfaces -- in the end, I'd like to end up with a hard 768Kbps limit per-LAN-interface (rather than a limit on eth0 pooled across all interfaces). I installed HTB.init, and riffing on the examples, tried to set this up on eth1 by putting three files into /etc/sysconfig/htb: /etc/sysconfig/htb/eth1 DEFAULT=30 R2Q=100 /etc/sysconfig/htb/eth1-2.root RATE=768Kbps BURST=15k /etc/sysconfig/htb/eth1-2:30.dfl RATE=768Kbps CEIL=788Kbps BURST=15k LEAF=sfq I can /etc/init.d/htb start and /etc/init.d/htb stats and see information that /seems/ to suggest it's working...but when I try pulling a large file via the WAN interface the shaping clearly isn't in effect. Any suggestions? My guess is it has something to do with where the shaping falls in the NAT chain, but I really have no idea where to begin troubleshooting this. ---- Update: Here's my /etc/init.d/htb list output, it seems to make sense -- the default rate for eth1 is 768Kbps? ### eth0: queueing disciplines qdisc htb 1: root refcnt 2 r2q 100 default 30 direct_packets_stat 0 qdisc sfq 30: parent 1:30 limit 127p quantum 1514b perturb 10sec ### eth0: traffic classes class htb 1:2 root rate 768000bit ceil 768000bit burst 1599b cburst 1599b class htb 1:30 parent 1:2 leaf 30: prio 0 rate 6144Kbit ceil 6144Kbit burst 15Kb cburst 1598b ### eth0: filtering rules filter parent 1: protocol ip pref 100 u32 filter parent 1: protocol ip pref 100 u32 fh 800: ht divisor 1 filter parent 1: protocol ip pref 100 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:30 match 00000000/00000000 at 12 match 00000000/00000000 at 16 ### eth1: queueing disciplines qdisc htb 1: root refcnt 2 r2q 100 default 30 direct_packets_stat 0 qdisc sfq 30: parent 1:30 limit 127p quantum 1514b perturb 10sec ### eth1: traffic classes class htb 1:2 root rate 768000bit ceil 768000bit burst 1599b cburst 1599b class htb 1:30 parent 1:2 leaf 30: prio 0 rate 6144Kbit ceil 6144Kbit burst 15Kb cburst 1598b

  Read the article

• cURL hangs trying to upload file from stdin

  - by SidneySM

  I'm trying to PUT a file with cURL. This hangs: curl -vvv --digest -u user -T - https://example.com/file.txt < file This does not: curl -vvv --digest -u user -T file https://example.com/file.txt What's going on? * About to connect() to example.com port 443 (#0) * Trying 0.0.0.0... connected * Connected to example.com (0.0.0.0) port 443 (#0) * SSLv3, TLS handshake, Client hello (1): * SSLv3, TLS handshake, Server hello (2): * SSLv3, TLS handshake, CERT (11): * SSLv3, TLS handshake, Server key exchange (12): * SSLv3, TLS handshake, Server finished (14): * SSLv3, TLS handshake, Client key exchange (16): * SSLv3, TLS change cipher, Client hello (1): * SSLv3, TLS handshake, Finished (20): * SSLv3, TLS change cipher, Client hello (1): * SSLv3, TLS handshake, Finished (20): * SSL connection using DHE-RSA-AES256-SHA * Server certificate: * subject: serialNumber=jJakwdOewDicmqzIorLkKSiwuqfnzxF/, C=US, O=*.example.com, OU=GT01234567, OU=See www.example.com/resources/cps (c)10, OU=Domain Control Validated - ExampleSSL(R), CN=*.example.com * start date: 2010-01-26 07:06:33 GMT * expire date: 2011-01-28 11:22:07 GMT * common name: *.example.com (matched) * issuer: C=US, O=Equifax, OU=Equifax Secure Certificate Authority * SSL certificate verify ok. * Server auth using Digest with user 'user' > PUT /file.txt HTTP/1.1 > User-Agent: curl/7.19.4 (universal-apple-darwin10.0) libcurl/7.19.4 OpenSSL/0.9.8l zlib/1.2.3 > Host: example.com > Accept: */* > Transfer-Encoding: chunked > Expect: 100-continue > < HTTP/1.1 100 Continue

  Read the article

• Trying to setup catchall mail forwarding on my rackspace's cloudspace server

  - by bob_cobb

  I'm running Ubuntu 12 Precise Pangolin and am trying to configure my server to catchall mail sent to it and forward it to my gmail address. I've been trying lots of examples online like editing my main.cf file which looks like this: smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = destiny alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = /etc/mailname mydestination = destiny, localhost.localdomain, localhost relayhost = smtp.sendgrid.net mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_size_limit = 51200000 recipient_delimiter = + inet_interfaces = all inet_protocols = all In my /etc/postfix/virtual I have: @mydomain.com [email protected] @myotherdomain.com [email protected] Which isn't working when I email [email protected] or [email protected]. So I got the recommendation to add the following to my /etc/alias: postmaster:root root:[email protected] restarted postfix, and tried emailing [email protected] or [email protected] but it still won't send. Does anyone have any idea what I'm doing wrong here? I'd appreciate any help.

  Read the article

• UAC being turned off once a day on Windows 7

  - by Mehper C. Palavuzlar

  I have strange problem on my HP laptop. This began to happen recently. Whenever I start my machine, Windows 7 Action Center displays the following warning: You need to restart your computer for UAC to be turned off. Actually, this does not happen if it happened once on a specific day. For example, when I start the machine in the morning, it shows up; but it never shows up in the subsequent restarts within that day. On the next day, the same thing happens again. I never disable UAC, but obviously some rootkit or virus causes this. As soon as I get this warning, I head for the UAC settings, and re-enable UAC to dismiss this warning. This is a bothersome situation as I can't fix it. First, I have run a full scan on the computer for any probable virus and malware/rootkit activity, but TrendMicro OfficeScan said that no viruses have been found. I went to an old Restore Point using Windows System Restore, but the problem was not solved. What I have tried so far (which couldn't find the rootkit): TrendMicro OfficeScan Antivirus AVAST Malwarebytes' Anti-malware Ad-Aware Vipre Antivirus GMER TDSSKiller (Kaspersky Labs) HiJackThis RegRuns UnHackMe SuperAntiSpyware Portable Tizer Rootkit Razor (*) Sophos Anti-Rootkit SpyHunter 4 There are no other strange activities on the machine. Everything works fine except this bizarre incident. What could be the name of this annoying rootkit? How can I detect and remove it? EDIT: Below is the log file generated by HijackThis: Logfile of Trend Micro HijackThis v2.0.4 Scan saved at 13:07:04, on 17.01.2011 Platform: Windows 7 (WinNT 6.00.3504) MSIE: Internet Explorer v8.00 (8.00.7600.16700) Boot mode: Normal Running processes: C:\Windows\system32\taskhost.exe C:\Windows\system32\Dwm.exe C:\Windows\Explorer.EXE C:\Program Files\CheckPoint\SecuRemote\bin\SR_GUI.Exe C:\Windows\System32\igfxtray.exe C:\Windows\System32\hkcmd.exe C:\Windows\system32\igfxsrvc.exe C:\Windows\System32\igfxpers.exe C:\Program Files\Hewlett-Packard\HP Wireless Assistant\HPWAMain.exe C:\Program Files\Synaptics\SynTP\SynTPEnh.exe C:\Program Files\Hewlett-Packard\HP Quick Launch Buttons\QLBCTRL.exe C:\Program Files\Analog Devices\Core\smax4pnp.exe C:\Program Files\Hewlett-Packard\HP Quick Launch Buttons\VolCtrl.exe C:\Program Files\LightningFAX\LFclient\lfsndmng.exe C:\Program Files\Common Files\Java\Java Update\jusched.exe C:\Program Files\Microsoft Office Communicator\communicator.exe C:\Program Files\Iron Mountain\Connected BackupPC\Agent.exe C:\Program Files\Trend Micro\OfficeScan Client\PccNTMon.exe C:\Program Files\Microsoft LifeCam\LifeExp.exe C:\Program Files\Hewlett-Packard\Shared\HpqToaster.exe C:\Program Files\Windows Sidebar\sidebar.exe C:\Program Files\mimio\mimio Studio\system\aps_tablet\atwtusb.exe C:\Program Files\Microsoft Office\Office12\OUTLOOK.EXE C:\Program Files\Babylon\Babylon-Pro\Babylon.exe C:\Program Files\Mozilla Firefox\firefox.exe C:\Users\userx\Desktop\HijackThis.exe R1 - HKCU\Software\Microsoft\Internet Explorer\Main,Search Page = http://go.microsoft.com/fwlink/?LinkId=54896 R0 - HKCU\Software\Microsoft\Internet Explorer\Main,Start Page = about:blank R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Default_Page_URL = http://go.microsoft.com/fwlink/?LinkId=69157 R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Default_Search_URL = http://go.microsoft.com/fwlink/?LinkId=54896 R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Search Page = http://go.microsoft.com/fwlink/?LinkId=54896 R0 - HKLM\Software\Microsoft\Internet Explorer\Main,Start Page = http://go.microsoft.com/fwlink/?LinkId=69157 R0 - HKLM\Software\Microsoft\Internet Explorer\Search,SearchAssistant = R0 - HKLM\Software\Microsoft\Internet Explorer\Search,CustomizeSearch = R1 - HKCU\Software\Microsoft\Windows\CurrentVersion\Internet Settings,AutoConfigURL = http://www.yaysat.com.tr/proxy/proxy.pac R0 - HKCU\Software\Microsoft\Internet Explorer\Toolbar,LinksFolderName = O2 - BHO: AcroIEHelperStub - {18DF081C-E8AD-4283-A596-FA578C2EBDC3} - C:\Program Files\Common Files\Adobe\Acrobat\ActiveX\AcroIEHelperShim.dll O2 - BHO: Babylon IE plugin - {9CFACCB6-2F3F-4177-94EA-0D2B72D384C1} - C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll O2 - BHO: Java(tm) Plug-In 2 SSV Helper - {DBC80044-A445-435b-BC74-9C25C1C588A9} - C:\Program Files\Java\jre6\bin\jp2ssv.dll O4 - HKLM\..\Run: [IgfxTray] C:\Windows\system32\igfxtray.exe O4 - HKLM\..\Run: [HotKeysCmds] C:\Windows\system32\hkcmd.exe O4 - HKLM\..\Run: [Persistence] C:\Windows\system32\igfxpers.exe O4 - HKLM\..\Run: [hpWirelessAssistant] C:\Program Files\Hewlett-Packard\HP Wireless Assistant\HPWAMain.exe O4 - HKLM\..\Run: [SynTPEnh] C:\Program Files\Synaptics\SynTP\SynTPEnh.exe O4 - HKLM\..\Run: [QlbCtrl.exe] C:\Program Files\Hewlett-Packard\HP Quick Launch Buttons\QlbCtrl.exe /Start O4 - HKLM\..\Run: [SoundMAXPnP] C:\Program Files\Analog Devices\Core\smax4pnp.exe O4 - HKLM\..\Run: [Adobe Reader Speed Launcher] "C:\Program Files\Adobe\Reader 9.0\Reader\Reader_sl.exe" O4 - HKLM\..\Run: [Adobe ARM] "C:\Program Files\Common Files\Adobe\ARM\1.0\AdobeARM.exe" O4 - HKLM\..\Run: [lfsndmng] C:\Program Files\LightningFAX\LFclient\LFSNDMNG.EXE O4 - HKLM\..\Run: [SunJavaUpdateSched] "C:\Program Files\Common Files\Java\Java Update\jusched.exe" O4 - HKLM\..\Run: [Communicator] "C:\Program Files\Microsoft Office Communicator\communicator.exe" /fromrunkey O4 - HKLM\..\Run: [AgentUiRunKey] "C:\Program Files\Iron Mountain\Connected BackupPC\Agent.exe" -ni -sss -e http://localhost:16386/ O4 - HKLM\..\Run: [OfficeScanNT Monitor] "C:\Program Files\Trend Micro\OfficeScan Client\pccntmon.exe" -HideWindow O4 - HKLM\..\Run: [Babylon Client] C:\Program Files\Babylon\Babylon-Pro\Babylon.exe -AutoStart O4 - HKLM\..\Run: [LifeCam] "C:\Program Files\Microsoft LifeCam\LifeExp.exe" O4 - HKCU\..\Run: [Sidebar] C:\Program Files\Windows Sidebar\sidebar.exe /autoRun O4 - Global Startup: mimio Studio.lnk = C:\Program Files\mimio\mimio Studio\mimiosys.exe O8 - Extra context menu item: Microsoft Excel'e &Ver - res://C:\PROGRA~1\MICROS~1\Office12\EXCEL.EXE/3000 O8 - Extra context menu item: Translate this web page with Babylon - res://C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll/ActionTU.htm O8 - Extra context menu item: Translate with Babylon - res://C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll/Action.htm O9 - Extra button: Research - {92780B25-18CC-41C8-B9BE-3C9C571A8263} - C:\PROGRA~1\MICROS~1\Office12\REFIEBAR.DLL O9 - Extra button: Translate this web page with Babylon - {F72841F0-4EF1-4df5-BCE5-B3AC8ACF5478} - C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll O9 - Extra 'Tools' menuitem: Translate this web page with Babylon - {F72841F0-4EF1-4df5-BCE5-B3AC8ACF5478} - C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll O16 - DPF: {00134F72-5284-44F7-95A8-52A619F70751} (ObjWinNTCheck Class) - https://172.20.12.103:4343/officescan/console/html/ClientInstall/WinNTChk.cab O16 - DPF: {08D75BC1-D2B5-11D1-88FC-0080C859833B} (OfficeScan Corp Edition Web-Deployment SetupCtrl Class) - https://172.20.12.103:4343/officescan/console/html/ClientInstall/setup.cab O17 - HKLM\System\CCS\Services\Tcpip\Parameters: Domain = yaysat.com O17 - HKLM\Software\..\Telephony: DomainName = yaysat.com O17 - HKLM\System\CS1\Services\Tcpip\Parameters: Domain = yaysat.com O17 - HKLM\System\CS2\Services\Tcpip\Parameters: Domain = yaysat.com O18 - Protocol: qcom - {B8DBD265-42C3-43E6-B439-E968C71984C6} - C:\Program Files\Common Files\Quest Shared\CodeXpert\qcom.dll O22 - SharedTaskScheduler: FencesShellExt - {1984DD45-52CF-49cd-AB77-18F378FEA264} - C:\Program Files\Stardock\Fences\FencesMenu.dll O23 - Service: Andrea ADI Filters Service (AEADIFilters) - Andrea Electronics Corporation - C:\Windows\system32\AEADISRV.EXE O23 - Service: AgentService - Iron Mountain Incorporated - C:\Program Files\Iron Mountain\Connected BackupPC\AgentService.exe O23 - Service: Agere Modem Call Progress Audio (AgereModemAudio) - LSI Corporation - C:\Program Files\LSI SoftModem\agrsmsvc.exe O23 - Service: BMFMySQL - Unknown owner - C:\Program Files\Quest Software\Benchmark Factory for Databases\Repository\MySQL\bin\mysqld-max-nt.exe O23 - Service: Com4QLBEx - Hewlett-Packard Development Company, L.P. - C:\Program Files\Hewlett-Packard\HP Quick Launch Buttons\Com4QLBEx.exe O23 - Service: hpqwmiex - Hewlett-Packard Development Company, L.P. - C:\Program Files\Hewlett-Packard\Shared\hpqwmiex.exe O23 - Service: OfficeScanNT RealTime Scan (ntrtscan) - Trend Micro Inc. - C:\Program Files\Trend Micro\OfficeScan Client\ntrtscan.exe O23 - Service: SMS Task Sequence Agent (smstsmgr) - Unknown owner - C:\Windows\system32\CCM\TSManager.exe O23 - Service: Check Point VPN-1 Securemote service (SR_Service) - Check Point Software Technologies - C:\Program Files\CheckPoint\SecuRemote\bin\SR_Service.exe O23 - Service: Check Point VPN-1 Securemote watchdog (SR_Watchdog) - Check Point Software Technologies - C:\Program Files\CheckPoint\SecuRemote\bin\SR_Watchdog.exe O23 - Service: Trend Micro Unauthorized Change Prevention Service (TMBMServer) - Trend Micro Inc. - C:\Program Files\Trend Micro\OfficeScan Client\..\BM\TMBMSRV.exe O23 - Service: OfficeScan NT Listener (tmlisten) - Trend Micro Inc. - C:\Program Files\Trend Micro\OfficeScan Client\tmlisten.exe O23 - Service: OfficeScan NT Proxy Service (TmProxy) - Trend Micro Inc. - C:\Program Files\Trend Micro\OfficeScan Client\TmProxy.exe O23 - Service: VNC Server Version 4 (WinVNC4) - RealVNC Ltd. - C:\Program Files\RealVNC\VNC4\WinVNC4.exe -- End of file - 8204 bytes As suggested in this very similar question, I have run full scans (+boot time scans) with RegRun and UnHackMe, but they also did not find anything. I have carefully examined all entries in the Event Viewer, but there's nothing wrong. Now I know that there is a hidden trojan (rootkit) on my machine which seems to disguise itself quite successfully. Note that I don't have the chance to remove the HDD, or reinstall the OS as this is a work machine subjected to certain IT policies on a company domain. Despite all my attempts, the problem still remains. I strictly need a to-the-point method or a pukka rootkit remover to remove whatever it is. I don't want to monkey with the system settings, i.e. disabling auto runs one by one, messing the registry, etc. EDIT 2: I have found an article which is closely related to my trouble: Malware can turn off UAC in Windows 7; “By design” says Microsoft. Special thanks(!) to Microsoft. In the article, a VBScript code is given to disable UAC automatically: '// 1337H4x Written by _____________ '// (12 year old) Set WshShell = WScript.CreateObject("WScript.Shell") '// Toggle Start menu WshShell.SendKeys("^{ESC}") WScript.Sleep(500) '// Search for UAC applet WshShell.SendKeys("change uac") WScript.Sleep(2000) '// Open the applet (assuming second result) WshShell.SendKeys("{DOWN}") WshShell.SendKeys("{DOWN}") WshShell.SendKeys("{ENTER}") WScript.Sleep(2000) '// Set UAC level to lowest (assuming out-of-box Default setting) WshShell.SendKeys("{TAB}") WshShell.SendKeys("{DOWN}") WshShell.SendKeys("{DOWN}") WshShell.SendKeys("{DOWN}") '// Save our changes WshShell.SendKeys("{TAB}") WshShell.SendKeys("{ENTER}") '// TODO: Add code to handle installation of rebound '// process to continue exploitation, i.e. place something '// evil in Startup folder '// Reboot the system '// WshShell.Run "shutdown /r /f" Unfortunately, that doesn't tell me how I can get rid of this malicious code running on my system. EDIT 3: Last night, I left the laptop open because of a running SQL task. When I came in the morning, I saw that UAC was turned off. So, I suspect that the problem is not related to startup. It is happening once a day for sure no matter if the machine is rebooted.

  Read the article

• Brick-level backup and restore with exchange 2007

  - by V. Romanov

  In the company I'm working for, we use exchange 2007 and backup it using netbackup. The backup is a daily complete backup of the information store and the direct corollary of this is that restores are hell. We need to restore the entire information store (over 80 gb), somehow merge it back with the original store, which causes problems. Alternatively, we tried using QUEST software to emulate exchange and restore mails from the emulation. However, this proved unreliable. The main problem with this entire situation is that we have to restore the whole information store and walk it through the restore process manually, and its quite absurd to be forced spend more than a day restoring even one erased email. (we have erased mail retention, but sometimes we need to restore older mail). in comparison, back in the day of XCH2003 and backupexec 12, we had complete brick level backup and restore at the push of a button. I've spoken to one of our chief sysadmins who claimed that the official response from microsoft to this issue was - "sorry guys, no brick level backup in XCH2007" which sounds ridiculous to me. Can someone shed some light on the situation? How do you backup your exchange2007 stores? Can you restore a single email quickly? A mailbox, perhaps?

  Read the article

• Apache2/mod_fcgid/PHP Process Limits Not Respected

  - by Daniel

  I've recently moved to Apache2 / mod_fcgid / PHP from nginx / php_fpm. This is the second server on which I've made this migration, but it's used much less frequently than the first, which is working like a charm. The problem is in the PHP processes that it's spawning. In looking at the mod_fcgid documentation, it appears that the default for killing idle processes is 300 seconds; I've changed that to 20. At this point, I'd be fine if 300 would work - but it's not happening. It's been running for nearly a day now, and server-status shows 12 active processes: Process name: php5 Pid Active Idle Accesses State 19243 84879 14420 11 Ready Process name: php5 Pid Active Idle Accesses State 20954 82143 149 22 Ready 20947 82149 149 22 Ready 20953 82143 149 13 Ready Process name: php5 Pid Active Idle Accesses State 20589 82765 23644 72 Ready Process name: php5 Pid Active Idle Accesses State 17663 86103 2034 117 Ready Process name: php5 Pid Active Idle Accesses State 19862 83961 1976 91 Ready Process name: php5 Pid Active Idle Accesses State 18495 85825 5164 18 Ready Process name: php5 Pid Active Idle Accesses State 25463 75109 23948 24 Ready Process name: php5 Pid Active Idle Accesses State 2466 60019 60016 2 Ready Process name: php5 Pid Active Idle Accesses State 20729 82541 12592 23 Ready Process name: php5 Pid Active Idle Accesses State 22135 80616 46361 6 Ready PHP applications are not being served at this point - Apache is returning a 503. However, it is still serving the server-status module, and mod_mono/Mono 2.10 applications are still being served. The problem is with the PHP. /etc/apache2/mods-available/fcgid.conf... <IfModule mod_fcgid.c> AddHandler fcgid-script .fcgi FcgidConnectTimeout 10 FcgidMaxRequestsPerProcess 500 FcgidIdleTimeout 20 FcgidFixPathinfo 1 FcgidMaxProcesses 10 </IfModule> (heh - Max Processes isn't being respected either...) Of course, fcgid.conf is smylinked in mods-enabled.

  Read the article

• Leopard mail.app quoted-printable weirdness

  - by pehrs

  I am not sure if this is a bug in mail.app, or a configuration I just can't find. It might also be a strange sideffect of GPGmail. Mail.app correctly displays all e-mails on my IMAP server, except for the e-mails in my "Sent Messages" folder. In the sent messages folder it messes up åäö, in typical quoted-printable with wrong char-set fashion. They become ‰ˆ. When looking at the source of the e-mails it seems like the header generated by mail.app is correct: Message-Id: <> From: To: In-Reply-To: <> Content-Type: multipart/signed; protocol="application/pgp-signature"; micalg=pgp-sha1; boundary="Apple-Mail-4--741321197" X-Smtp-Server: smtp.example.com Content-Transfer-Encoding: 7bit Mime-Version: 1.0 (Apple Message framework v936) Subject: Example subject Date: Fri, 26 Mar 2010 10:14:14 +0100 References: <> X-Pgp-Agent: GPGMail 1.2.0 (v56) This is an OpenPGP/MIME signed message (RFC 2440 and 3156) --Apple-Mail-4--741321197 Content-Type: text/plain; charset=ISO-8859-1; format=flowed; delsp=yes Content-Transfer-Encoding: quoted-printable <Text here with =E5=E4=F6> --Apple-Mail-4--741321197 content-type: application/pgp-signature; x-mac-type=70674453; name=PGP.sig content-description: This is a digitally signed message part content-disposition: inline; filename=PGP.sig content-transfer-encoding: 7bit -----BEGIN PGP SIGNATURE----- Version: GnuPG/MacGPG2 v2.0.12 (Darwin) iEYEARECAAYFAkus62kACgkQlIRLofxhDjYnnwCcDmCXuMGsKlh3a418s12coJgn 36sAoKMdkP3+g/OMK+Ps7AbjQq4Nbqzv =XMko -----END PGP SIGNATURE----- --Apple-Mail-4--741321197-- Thunderbird has no problem displaying the messages. So, how can I get mail.app to use the correct charset?

  Read the article

• How to enable error log in lighttpd properly?

  - by Tomaszs

  I have a Centos 5 system with Lighttpd and fastcgi enabled. It does log access but does not log errors. I have Internal Server Error 500 and no info in log and when I try to open not -existing file also - no info in error log. How to enable it properly? Below is list of modules that I've enabled: server.modules = ( "mod_rewrite", "mod_redirect", "mod_alias", # "mod_access", # "mod_cml", # "mod_trigger_b4_dl", # "mod_auth", "mod_status", "mod_setenv", "mod_fastcgi", # "mod_webdav", # "mod_proxy_core", # "mod_proxy_backend_fastcgi", # "mod_proxy_backend_scgi", # "mod_proxy_backend_ajp13", # "mod_simple_vhost", # "mod_evhost", # "mod_userdir", # "mod_cgi", # "mod_compress", # "mod_ssi", # "mod_usertrack", # "mod_expire", # "mod_secdownload", # "mod_rrdtool", "mod_accesslog" ) Here are setting of debugging: ## enable debugging #debug.log-request-header = "enable" #debug.log-response-header = "enable" #debug.log-request-handling = "enable" debug.log-file-not-found = "enable" #debug.log-condition-handling = "enable" Setting of path to error and access log: ## where to send error-messages to server.errorlog = "/home/lxadmin/httpd/lighttpd/error.log" #### accesslog module accesslog.filename = "/home/lxadmin/httpd/lighttpd/ligh.log" Settings of fastcgi: fastcgi.debug = 1 fastcgi.server = ( ".php" => (( "bin-path" => "/usr/bin/php-cgi", "socket" => "/tmp/php.socket", "max-procs" => 12, "bin-environment" => ( "PHP_FCGI_CHILDREN" => "2", "PHP_FCGI_MAX_REQUESTS" => "500" ) ))) And in included config file I have: server.errorlog = "/home/httpd/mywebsite.com/stats/mywebsite.com-error_log" What comes to log files: /home/httpd/mywebsite.com/stats/ -rw-r--r-- 1 apache apache 5173239 May 16 11:34 mywebsite.com-custom_log -rwxrwxrwx 1 root root 0 Mar 27 2009 mywebsite.com-error_log /home/lxadmin/httpd/lighttpd/ -rwxrwxrwx 1 apache apache 2184 Apr 22 22:59 error.log -rwxrwxrwx 1 apache apache 6088621 May 16 11:26 ligh.log I gave error logs chmod 777 for a try to check if it's the issue, but apparently it's not. So my question is: what to do to have error log enabled?

  Read the article

• Extend RAID 1 (HP SmartArray P410i) running Linux

  - by Oliver

  I took over a fairly simple server setup with the following RAID 1 config running Ubuntu 11.10 (Kernel 3.0.0-12-server x86_64): => ctrl all show config Smart Array P410i in Slot 0 (Embedded) (sn: removed) array A (SAS, Unused Space: 1335535 MB) logicaldrive 1 (279.4 GB, RAID 1, OK) physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 1 TB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 1 TB, OK) Initially there were two 300GB disks that got replaced by 1TB disks and I now have to extend the logical volume to use that extra space. However, when trying to do so I get the following warning: => ctrl slot=0 ld 1 modify size=max Warning: Extension may not be supported on certain operating systems. Performing extension on these operating systems can cause data to become inaccessible. See ACU documentation for details. Continue? (y/n) Is it safe to say yes or am I at risk of corrupting the file system / loosing data? Rearranging and extending the file system afterwards shouldn't be an issue as I can take the server offline and boot from a gparted live disk. Here's the config of the RAID controller in use: => ctrl all show detail Smart Array P410i in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Serial Number: removed RAID 6 (ADG) Status: Disabled Controller Status: OK Hardware Revision: Rev C Firmware Version: 5.12 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: False Drive Write Cache: Disabled SATA NCQ Supported: True And the partition table: Number Start End Size Type File system Flags 1 1049kB 274GB 274GB primary ext4 boot 2 274GB 300GB 25.8GB extended 5 274GB 300GB 25.8GB logical linux-swap(v1)

  Read the article

• Iptables Forwarding problem

  - by ankit

  Hi all, I had initally asked question about sertting up my linux box for natting for my home network and was given suggestions in the thread here. Did not want to clutter the old question so starting a new one here. based on the earlier suggestions, i have come up with the following rules ... :PREROUTING ACCEPT [1:48] :OUTPUT ACCEPT [12:860] :POSTROUTING ACCEPT [3:228] -A POSTROUTING -o eth0 -j MASQUERADE COMMIT *filter :INPUT DROP [3:228] :FORWARD DROP [0:0] :OUTPUT DROP [0:0] -A INPUT -i lo -j ACCEPT -A INPUT -i eth0 -p icmp -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 443 -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 22 -j ACCEPT -A FORWARD -i eth1 -p icmp -j ACCEPT -A FORWARD -i eth1 -p tcp -m tcp --dport 80 -j ACCEPT -A FORWARD -i eth1 -p tcp -m tcp --dport 443 -j ACCEPT -A OUTPUT -p icmp -j ACCEPT -A OUTPUT -j ACCEPT COMMIT If you notice, i do have the proper MASQURADING rule and the proper FORWARD filter rule as well. However i am facing 2 problems On the linux box itself DNS resolving is not working the lan clients connected to the linux box, are still not able to get to internet. when i ping something from them, i see the DROP count in iptables INPUT rule increasing. now my question is, when i am pinging something from the lan client, how come it is being matched by the input chain ?! should it be in the forward chain ? Chain INPUT (policy DROP 20 packets, 2314 bytes) pkts bytes target prot opt in out source destination 99 9891 ACCEPT all -- lo any anywhere anywhere 0 0 ACCEPT icmp -- eth0 any anywhere anywhere 0 0 ACCEPT tcp -- eth0 any anywhere anywhere tcp dpt:http 0 0 ACCEPT tcp -- eth0 any anywhere anywhere tcp dpt:https 122 9092 ACCEPT tcp -- eth0 any anywhere anywhere tcp dpt:ssh Thanks ankit

  Read the article

• OpenSwan (IPSEC) on Fedora 13 with Snow Leopard as a client

  - by sicn

  I recently installed OpenSwan on my Fedora 13 machine. I want to use it to connect with Mac OS X with L2TP over IPSEC, unfortunately I am already stuck on the IPSEC-negotation part. My server is running behind a NATted firewall so my external IP differs from the server's IP. The server has a fixed IP on the network and the same is almost always valid for the clients (they are usually behind a NATted firewall). I installed OpenSwan on Fedora 13 and have following configuration: config setup protostack=netkey nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12 oe=off nhelpers=0 conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=3 rekey=no ikelifetime=8h keylife=1h type=transport left=my.servers.external.ip leftprotoport=17/1701 right=%any rightprotoport=17/0 IPSEC starts fine and listens to UDP 500 and 4500. These two ports are opened in the firewall and are forwarded fine to the server. In my /etc/ipsec.secrets file I have my.servers.external.ip %any: "LongAndDifficultPassword" And finally in my sysctl.conf (the redirect-entries are there because OpenSwan was strongly protesting about send/accept_redirects being active) I have net.ipv4.ip_forward = 1 net.ipv4.conf.all.send_redirects = 0 net.ipv4.conf.all.accept_redirects = 0 Running "ipsec verify" gives me "all greens" (except Opportunistic Encryption Support, which is DISABLED), however, when trying to connect my Mac gives me following in the logs: Nov 1 19:30:28 macbook pppd[4904]: pppd 2.4.2 (Apple version 412.3) started by user, uid 1011 Nov 1 19:30:28 macbook pppd[4904]: L2TP connecting to server 'my.servers.ip.address' (my.servers.ip.address)... Nov 1 19:30:28 macbook pppd[4904]: IPSec connection started Nov 1 19:30:28 macbook racoon[4905]: Connecting. Nov 1 19:30:28 macbook racoon[4905]: IKE Packet: transmit success. (Initiator, Main-Mode message 1). Nov 1 19:30:31 macbook racoon[4905]: IKE Packet: transmit success. (Phase1 Retransmit). Nov 1 19:30:38: --- last message repeated 2 times --- Nov 1 19:30:38 macbook pppd[4904]: IPSec connection failed Any ideas at all?

  Read the article

• List symlinks in specific relative directories

  - by Clinton Blackmore

  I have a server that shares out user home folders over the network. Each user has a Cache folder. Sometimes a symlink is used to redirect this folder to the hard drive of whichever machine they are using (and sometimes that doesn't work and they have a broken symlink [which is a matter for another day].) I'm trying to find out which users have symlinks and which don't. Within the shared folder, to get to the Cache folder you would substitute folders like so: $GRADE/$USERNAME/Library/Caches Right now I'm searching to see which users have symlinks and which do not. I've come up with: cd /path/to/shared/home/folders sudo find . -name "Caches" -exec ls -ld {} \; and get results like this: lrwxr-xr-x@ 1 name0 ES_Students 27 Jan 18 11:05 ./CES_Grade_03/name0/Library/Caches -> /tmp/name0/Library/Caches drwx------ 11 name1 ES_Students 374 Dec 8 15:44 ./CES_Grade_03/name1/Library/Caches lrwxr-xr-x@ 1 name2 ES_Students 27 Feb 23 14:27 ./CES_Grade_03/name2/Library/Caches -> /tmp/name2/Library/Caches drwx------ 17 name3 ES_Students 578 Jan 25 11:13 ./CES_Grade_03/name3/Library/Caches drwx------ 12 name4 ES_Students 408 Mar 22 13:09 ./CES_Grade_03/name4/Library/Caches but it nags at me that there must be a better way. Yes, it is good enough, and a one-off task, but I want to know how to do it right! Surely, I should be able to do something like: cd /path/to/shared/home/folders sudo ls -ld **/**/Library/Caches I'm afraid that I don't know the proper syntax or if there is a recursive folder-replacing wildcard format in bash, and my google-fu failed me. So, how do I properly formulate the search?

  Read the article

• dd oflag=direct 5x fast

  - by César

  I have Centos 6.2 in server with this specs: 2xCPU 16 Core AMD Opteron 6282 SE 64GB RAM Raid controller H700 1GB cache NV - 2HD 74GB SAS 15Krpm RAID1 stripe 16k (OS Centos 6.2) sda - 4HD 146GB SAS 15Krpm RAID10 stripe 16k (ext4 bs 4096, no barriers) sdb -> /vol01 Raid controller H800 1GB cache nv - MD1200 12HD 300GB SAS 15Krpm RAID10 stripe 256k (For DB Postgres 8.3.18) (ext4 bs 4096, stride 64, stripe-width 384, no barriers) sdc -> /vol02 I'm benchmarking IO speed with dd, and view thah if in RAID10 12 disk exec: dd if=/dev/zero of=DD bs=8M count=10000 oflag=direct 10000+0 records in 10000+0 records out 83886080000 bytes (84 GB) copied, 126,03 s, 666 MB/s but if I remove "oflag=direct" option obtain about 80 MB/s. In read benchmark, results are similar: dd of=/dev/null if=DD bs=8M count=10000 iflag=direct 10000+0 records in 10000+0 records out 83886080000 bytes (84 GB) copied, 79,5918 s, 1,1 GB/s If remove iflag=direct obtain 150MB/s... I don't understand this huge differences, on other machines y don't have this behavior. Can I have some kernel parameter misconfigured? Thanks!

  Read the article

• How to read an Excel file, get and set the information using POI

  - by user1399713

  I'm using Java to read a form that is in an Excel spreadsheet that the user fills in with information about geometric shape. Ex: Shape :_________ Color :_________ Area: _________ Perimeter:________ So far the code I have can I can read what I want in the form and print out the values of Shape, Color, Area, Perimeter. public class RangeSetter { /** * @param args * @throws IOException */ public static void main(String[] args) throws IOException { FileInputStream file = new FileInputStream(new File("test2.xls")); //C:\Users\Yo\Documents // Setup code String cname = "Shape"; HSSFWorkbook wb = new HSSFWorkbook(file); // retrieve workbook // Retrieve the named range // Will be something like "$C$10,$D$12:$D$14"; int namedCellIdx = wb.getNameIndex(cname); Name aNamedCell = wb.getNameAt(namedCellIdx); // Retrieve the cell at the named range and test its contents // Will get back one AreaReference for C10, and // another for D12 to D14 AreaReference[] arefs = AreaReference.generateContiguous(aNamedCell.getRefersToFormula()); for (int i=0; i<arefs.length; i++) { // Only get the corners of the Area // (use arefs[i].getAllReferencedCells() to get all cells) CellReference[] crefs = arefs[i].getAllReferencedCells(); for (int j=0; j<crefs.length; j++) { // Check it turns into real stuff Sheet s = wb.getSheet(crefs[j].getSheetName()); Row r = s.getRow(crefs[j].getRow()); Cell c = r.getCell(crefs[j].getCol()); if (c!= null ){ switch(c.getCellType()){ case Cell.CELL_TYPE_STRING: System.out.println(c.getStringCellValue()); } } } } What I want to do is to create a method that gets the that information and another that sets it. So far I can only print to the console

  Read the article

• How do I run a stable Windows XP kvm guest on Ubuntu 10.04?

  - by Jean-Paul Calderone

  I have three Windows XP guests running on a recently upgraded 64-bit Ubuntu 10.04 system. Occasionally (on the order of once every few days), one of the guests will become non-responsive and the kvm process on the host which is running that guest will start consuming 100% CPU. It will continue to do so until it is killed. When restarted, it will be fine for a while, and then the issue repeats. The kvm command line used to run all three guests is this: /usr/bin/kvm -S -M pc-0.12 -enable-kvm -m 1024 -smp 1 -name bigdog21vmxp1 \ -uuid ea47ff84-125b-16f7-9a4d-a6d0d8bab46a \ -chardev socket,id=monitor,path=/var/lib/libvirt/qemu/bigdog21vmxp1.monitor,server,nowait \ -monitor chardev:monitor \ -localtime \ -boot c \ -drive file=/var/lib/libvirt/images/windowsxp-1.qcow2,if=ide,index=0,boot=on,format=qcow2 \ -net nic,macaddr=54:52:00:02:06:0e,vlan=0,name=nic.0 \ -net tap,fd=58,vlan=0,name=tap.0 \ -chardev pty,id=serial0 \ -serial chardev:serial0 \ -parallel none \ -usb \ -usbdevice tablet \ -vnc 127.0.0.1:1 \ -k en-us \ -vga cirrus \ -soundhw es1370 Why do the systems misbehave this way sometimes? And what configuration can I change in order to fix it? Or, if the problem is due to a bug in kvm, what is the process for isolating a kvm failure so that the developers have a chance of fixing it?

  Read the article

• lm-sensors - always returns 32 degrees (celsius) for temperature

  - by mopoke

  On my VIA EPIA motherboard (using VIA VT8231 ISA bridge), I get strange output for the lm-sensors temperature reading. It always returns 32 degrees (celsius). I have previously had correct output for temperature (my munin graphs show temperatures typically in the range of 50 to 60 degrees. I've tried uninstalling (and purging) the lm-sensors package, have re-run sensors-detect a number of times and rebooted but nothing seems to change the output. I am running Ubuntu Karmic Koala (9.10). Anyone got any bright ideas on what I might have missed? uname -a: Linux george 2.6.31-16-386 #53-Ubuntu SMP Tue Dec 8 06:39:34 UTC 2009 i686 GNU/Linux cpuinfo: processor : 0 vendor_id : CentaurHauls cpu family : 6 model : 7 model name : VIA Samuel 2 stepping : 3 cpu MHz : 399.000 cache size : 64 KB fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 1 wp : yes flags : fpu de tsc msr cx8 mtrr pge mmx 3dnow up bogomips : 800.04 clflush size : 32 power management: lspci: 00:00.0 Host bridge: VIA Technologies, Inc. VT8601 [Apollo ProMedia] (rev 05) 00:01.0 PCI bridge: VIA Technologies, Inc. VT8601 [Apollo ProMedia AGP] 00:11.0 ISA bridge: VIA Technologies, Inc. VT8231 [PCI-to-ISA Bridge] (rev 10) 00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) 00:11.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1e) 00:11.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1e) 00:11.4 Bridge: VIA Technologies, Inc. VT8235 ACPI (rev 10) 00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT82C686 AC97 Audio Controller (rev 40) 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 51) 01:00.0 VGA compatible controller: Trident Microsystems CyberBlade/i1 (rev 6a) sensors: acpitz-virtual-0 Adapter: Virtual device temp1: +32.0°C (crit = +60.0°C)

  Read the article

• EEE PC dropbox server running 24/7

  - by microspino

  I'd like to create a mini dropbox and print server on a small soho network of 5 users (all of them use windows XP desktops). The device need to run 24/7 or at least 12/7 (I can accept just workday hours too but the other two options would be better). Dropbox mini server: I mean I will have a 90gb dropbox on every computer on my network LAN syncing with It and the one onto It syncing to the web. Print Server: I have Samsung SCX 4521F (fax/print/scan/copy), Samsung ML2010, HP Laser jet P1006, HP Color Laserjet CP1215, HP Office jet pro K8600, HP Design jet 500. All of them now are connected using little print servers and I want to get rid of them hooking everything to this mini server. The fax/print/scan/copy machine need to stay connected to a PC to make me able to use the software that comes with It. The mini server would save me on this too. Fax/Scan server: since I have the above mentioned fax/print/scan/copy machine I would like to make people use It from/to their computers through the mini server. I thought to a recent EEEBOX machine because I heard good things about ATOM cpus and because It seems that a recent BIOS version could switch It off and on autonomously. I'd like to listen some advice from You. Best of all would be: If You have something similar running for a long time If You disagree with this hardware choice and If You would suggest some other device. If You see any issues with my printing setup Anything else ;) My budget is from Zero (using right sw to build something on top on a old PC) to 500€ max.

  Read the article

• How can I run Gnome or KDE locally in Cygwin?

  - by John Peter Thompson Garcés

  Apparently it is possible to do this using cygwin ports, as can be seen in screenshots. I followed this how-to to get apt-cygports set up, and I used it to install gnome-session. This how-to supposedly gives the commands needed to run Gnome or KDE, but whenever I try to run Gnome, a blank X-window pops up and then quickly disappears. Here is the terminal output: $ startx /usr/bin/dbus-launch gnome-session xauth: file /home/jpthomps/.serverauth.4168 does not exist Welcome to the XWin X Server Vendor: The Cygwin/X Project Release: 1.10.3.0 OS: Windows 7 Service Pack 1 [Windows NT 6.1 build 7601] (WoW64) Package: version 1.10.3-12 built 2011-08-22 XWin was started with the following command line: /usr/bin/X :0 -auth /home/jpthomps/.serverauth.4168 (II) xorg.conf is not supported (II) See http://x.cygwin.com/docs/faq/cygwin-x-faq.html for more information LoadPreferences: /home/jpthomps/.XWinrc not found LoadPreferences: Loading /etc/X11/system.XWinrc LoadPreferences: Done parsing the configuration file... winDetectSupportedEngines - DirectDraw installed, allowing ShadowDD winDetectSupportedEngines - Windows NT, allowing PrimaryDD winDetectSupportedEngines - DirectDraw4 installed, allowing ShadowDDNL winDetectSupportedEngines - Returning, supported engines 0000001f winSetEngine - Using Shadow DirectDraw NonLocking winScreenInit - Using Windows display depth of 32 bits per pixel winFinishScreenInitFB - Masks: 00ff0000 0000ff00 000000ff Screen 0 added at virtual desktop coordinate (0,0). MIT-SHM extension disabled due to lack of kernel support XFree86-Bigfont extension local-client optimization disabled due to lack of shared memory support in the kernel (II) AIGLX: Loaded and initialized /usr/lib/dri/swrast_dri.so (II) GLX: Initialized DRISWRAST GL provider for screen 0 winPointerWarpCursor - Discarding first warp: 637 478 (--) 5 mouse buttons found (--) Setting autorepeat to delay=500, rate=31 (--) Windows keyboard layout: "00000409" (00000409) "US", type 4 (--) Found matching XKB configuration "English (USA)" (--) Model = "pc105" Layout = "us" Variant = "none" Options = "none" Rules = "base" Model = "pc105" Layout = "us" Variant = "none" Options = "none" winBlockHandler - pthread_mutex_unlock() winProcEstablishConnection - winInitClipboard returned. winClipboardProc - DISPLAY=:0.0 winClipboardProc - XOpenDisplay () returned and successfully opened the display. xinit: XFree86_VT property unexpectedly has 0 items instead of 1 xinit: connection to X server lost waiting for X server to shut down winClipboardProc - winClipboardFlushWindowsMessageQueue trapped WM_QUIT message, exiting main loop. winClipboardProc - XDestroyWindow succeeded. winClipboardProc - Clipboard disabled - Exit from server winDeinitMultiWindowWM - Noting shutdown in progress

  Read the article

• Google Chrome sync: limit for bookmarks & extensions?

  - by Lyubomyr Shaydariv

  Actually, Chrome is my favorite web-browser, and one of its most powerful features is synchronizing the actual data into a Google account. For the last years I gained a lot of bookmarks and from time to time browse the extensions gallery to find new valuable ones. Really, synchronizing between my work and home PC's freed me from manual sync. And for the recent months I experience strange glitches. I guess it may be caused by a lot of stored bookmarks (potentially about 3K [in estimate], but please don't ask why :)) and extensions (about 130 installed but only 10-15 daily used). I can mention the following strange things: Recently added bookmarks sometimes are not synchronized (e.g. I put a bookmark at work, but it's not guaranteed I can see it that evening), despite about:sync indicates a good sync process. Sometimes recently modified bookmarks appear in either (let's call) last at home or last at work bookmark folders. Sometimes bookmarks are not synced at all. (Moreover, Chromium versions may even crash) Extensions are not synced now at all. Perhaps, there's another reason, but Google Mail Checker and Google Reader Notifier do not show indicators of incoming e-mails and news. ... I'm not sure but it looks like I might exceed Chrome internal sync limits... Is it right? Are there any workarounds, or should I make a massive bookmarks/extensions cleanup (I really don't want it :()? I mostly use Google Chrome Canary builds, and the my current one is 12.0.732.0. Thanks in advance. Update #1 (2001-04-19): I removed about 50 extensions that I'm not interested in (or that I consider as trash), and gained pretty some results: The extensions count is below 100 (exactly 97); The chrome://extensions page does not get slow (or even frozen) any more on enabling/disabling/uninstalling extensions; The extensions are seem to be synchronized now again.

  Read the article

• newsubtitles line not working in FFmpeg

  - by godMode

  i'm trying to run the following line on FFmpeg that will basically "re-format" an MKV file to MP4 without doing any re-encoding and also embed SRT subtitles onto the MP4 output: ffmpeg -i test.mkv -i test.srt -newsubtitle -acodec copy -vcodec copy test.mp4 Without the "-i test.srt -nwesubtitle" bit, it seems to work just fine; however, with it I get the following output: Seems stream 0 codec frame rate differs from container frame rate: 47.95 (5000000/104271) - 23.98 (24000/1001) Stream #0.0(eng): Video: h264, yuv420p, 1280x720 [PAR 1:1 DAR 16:9], 23.98 fps, 23.98 tbr, 1k tbn, 47.95 tbc Stream #0.1(eng): Subtitle: 0x0000 Metadata: title : English Stream #0.2(jpn): Audio: aac, 48000 Hz, stereo, s16 Metadata: title : Japanese 2.0 Stream #0.3(eng): Audio: aac, 48000 Hz, stereo, s16 Metadata: title : English 2.0 Stream #0.4(eng): Subtitle: 0x0000 Metadata: title : English Songs & Signs Stream #0.5: Attachment: 0x0000 Metadata: filename : MyriadPro-Bold.ttf Stream #0.6: Attachment: 0x0000 Metadata: filename : MyriadPro-RegularHaruhi.ttf Stream #0.7: Attachment: 0x0000 Metadata: filename : ChaparralPro-BoldIt.ttf Stream #0.8: Attachment: 0x0000 Metadata: filename : ChaparralPro-SemiboldIt.ttf Stream #0.9: Attachment: 0x0000 Metadata: filename : epmgobld_ending.ttf Stream #0.10: Attachment: 0x0000 Metadata: filename : epminbld_opening.ttf Stream #0.11: Attachment: 0x0000 Metadata: filename : Folks-Bold.ttf Stream #0.12: Attachment: 0x0000 Metadata: filename : GosmickSansBold.ttf Stream #0.13: Attachment: 0x0000 Metadata: filename : WarnockPro-LightDisp.ttf Stream #0.14: Attachment: 0x0000 Metadata: filename : epmgobld_ending.ttf Stream #0.15: Attachment: 0x0000 Metadata: filename : GosmickSansBold.ttf Stream #0.16: Attachment: 0x0000 Metadata: filename : Marker SD 1.2.ttf Stream #0.17: Attachment: 0x0000 Metadata: filename : MyriadPro-Bold.ttf Stream #0.18: Attachment: 0x0000 Metadata: filename : MyriadPro-RegularHaruhi.ttf Stream #0.19: Attachment: 0x0000 Metadata: filename : MyriadPro-SemiCn.ttf test.srt: Invalid data found when processing input I tried adding "-r pal", "-r ntsc" or "-r 23.98" thinking it was framerate issue with no change.

  Read the article

• What is stopping postfix from delivering mail to the local transport agent?

  - by Dark Star1

  I have the following settings ( as grabbed from my postconf -n output) alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no broken_sasl_auth_clients = yes config_directory = /etc/postfix content_filter = smtp-amavis:[127.0.0.1]:10024 inet_interfaces = all mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 maximal_backoff_time = 8000s maximal_queue_lifetime = 7d minimal_backoff_time = 1000s mydestination = $mydomain, localhost.$mydomain, localhost myhostname = //redacted mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname readme_directory = no recipient_delimiter = + relayhost = smtp_helo_timeout = 60s smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_hard_error_limit = 12 smtpd_recipient_limit = 10 smtpd_sasl_auth_enable = yes smtpd_sasl_authenticated_header = yes smtpd_sasl_local_domain = smtpd_sasl_path = private/auth smtpd_sasl_security_options = noanonymous smtpd_sasl_type = dovecot smtpd_soft_error_limit = 3 smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes unknown_local_recipient_reject_code = 450 virtual_alias_maps = mysql:/etc/postfix/mysql_virtual_alias_maps.cf, mysql:/etc/postfix/mysql_virtual_alias_domainaliases_maps.cf virtual_gid_maps = static:8 virtual_mailbox_base = /var/vmail virtual_mailbox_domains = mysql:/etc/postfix/mysql_virtual_domains_maps.cf virtual_mailbox_maps = mysql:/etc/postfix/mysql_virtual_mailbox_maps.cf, mysql:/etc/postfix/mysql_virtual_mailbox_domainaliases_maps.cf virtual_transport = virtual virtual_uid_maps = static:5000 postconf: warning: /etc/postfix/main.cf: unused parameter: virtual_overquota_bounce=yes postconf: warning: /etc/postfix/main.cf: unused parameter: virtual_mailbox_limit_maps=mysql:/etc/postfix/mysql_virtual_mailbox_limit_maps.cf postconf: warning: /etc/postfix/main.cf: unused parameter: virtual_maildir_limit_message=Sorry, the your maildir has overdrawn your diskspace quota, please free up some of spaces of your mailbox try again. postconf: warning: /etc/postfix/main.cf: unused parameter: virtual_create_maildirsize=yes postconf: warning: /etc/postfix/main.cf: unused parameter: virtual_mailbox_extended=yes postconf: warning: /etc/postfix/main.cf: unused parameter: virtual_mailbox_limit_override=yes postconf: warning: /etc/postfix/main.cf: unused parameter: smtpd_relay_restrictions=reject_unauth_pipelining, permit_mynetworks, permit_sasl_authenticated, reject_non_fqdn_recipient, reject_unauth_destination, check_policy_service inet:127.0.0.1:10023, permit I am nwe to mail server configurations but as I understand it from this message: status=deferred (mail transport unavailable) It means it can't deliver to the LDA. I am using postifx 2.9.6 on ubuntu 12.04 with dovecot 2.0.19

  Read the article

• MySQL encoding problem after site move

  - by Quan Zhou

  Guys, I need your help. Since last month my friend has lost his database on Dreamhost, he decided to move his wordpress based blog site (written in Chinese) to my server. He's using a wp-plugin called wp-db-backup to perform regular db backups. And the servers backgrounds are: Dreamhost: Linux 2.6.31.5-modsign-aufs2-grsec-2-opt mysql Ver 14.12 Distrib 5.0.16, for pc-linux-gnu (i386) using readline 5.0 apache2 unknown version My Server: Linux li159-46 2.6.32.12-x86_64-linode12 mysql Ver 14.14 Distrib 5.1.45, for debian-linux-gnu (x86_64) using readline 6.1 nginx 0.8.36 His site's encoding was UTF-8 in both wp-config and db. I imported his db backup file in UTF-8 by default, then I sync'd files using rsync from dreamhost, then I just changed the db address and nothing more. But when I take first look at the "new" site, it was full of unreadable characters, I met this problem before, I changed charset options in browser but none of them can make it displayed properly. Then I converted his db to GB18030, it works with only if browser set charset to GB18030 either GBK, but by default they recognize the charset as UTF-8. I tried to edit the headers but it doesn't work. What could I do now? Thx~~

  Read the article

• Cisco Catalyst 4500 Policy Based Routing

  - by Logan

  In order to test a new firewall I just set up I'm trying to implement policy based routing on our core switch. I want traffic from certain vlans to be routed to the new firewall while everything else continues being routed through the old firewall. I was trying to use this guide. Everything from that guide works fine except trying to run the "ip policy route-map" command in the interface configuration mode. IOS is telling me that such a command doesn't exist. A "show ip interface vlan" command says that policy routing is disabled. Any ideas? Output of "show ver": Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASEK9-M), Version 12.2(53)SG, RELEASE SOFTWARE (fc3) Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2009 by Cisco Systems, Inc. Compiled Thu 16-Jul-09 19:49 by prod_rel_team Image text-base: 0x10000000, data-base: 0x11D1E3CC ROM: 12.2(31r)SG2 Dagobah Revision 226, Swamp Revision 34 RTTMCB2223-1 uptime is 3 years, 22 weeks, 2 days, 19 hours, 28 minutes Uptime for this control processor is 51 weeks, 2 days, 18 hours, 2 minutes System returned to ROM by power-on System restarted at 19:22:02 UTC Tue Jul 12 2011 System image file is "bootflash:cat4500-ipbasek9-mz.122-53.sg.bin" ... cisco WS-C4510R (MPC8245) processor (revision 4) with 524288K bytes of memory. Processor board ID FOX103703W3 MPC8245 CPU at 400Mhz, Supervisor V Last reset from PowerUp 42 Virtual Ethernet interfaces 244 Gigabit Ethernet interfaces 511K bytes of non-volatile configuration memory. Configuration register is 0x2

  Read the article

< Previous Page | 378 379 380 381 382 383 384 385 386 387 388 389  | Next Page >