Highly available iSCSI target

Posted by sysetr on Ask Ubuntu See other posts from Ask Ubuntu or by sysetr
Published on 2012-10-29T15:31:17Z Indexed on 2012/11/02 5:24 UTC
Read the original article Hit count: 776

Filed under:

networking

|

iscsi

I'm in the process of setting up iSCSI target on DRBD following the steps detailed here.

I would appreciate if someone can answer and explain the following queries:

Is there a way to set up just 1 resource for iscsi config and storage? Why does iscsi.config have to have a separate resource (in drbd.conf).
Is it possible to put iscsi.config and iscsi.target in one disk?
If not possible, what would be a good ratio (space wise) for iscsi.config and iscsi.target? Assuming I need to set up a 1TB iscsi.storage, how much space should I allocate for iscsi.config?

© Ask Ubuntu or respective owner

Related posts about networking

Networking stopped working on Ubuntu

as seen on Super User - Search for 'Super User'
I installed Ubuntu 10.04 through the Wubi installer (Funny, I installed it today and thought I would have gotten 10.10). I had a network connection and everything was working fine. I rebooted my coumputer a couple of times and then suddenly, I could not connect to the network and when I click the… >>> More
Troubles with start up defenition of networking service in Ubuntu

as seen on Super User - Search for 'Super User'
I use Ubuntu 12.04.1. I put attention that networking script starting in runlevel 0: user@comp:/etc/rc0.d$ chkconfig -l networking networking 0:on 1:off 2:off 3:off 4:off 5:off 6:off When I try to move it working to appropriate run levels I get error: user@comp:/etc/rc0… >>> More
Installing the Elgg Social Networking CMS

as seen on Internet.com - Search for 'Internet.com'
One Open Source CMS that stands out above the rest for small businesses and personal networks is the Elgg open source "social engine," which can be used to create social applications. Scott Clark shows you how to install and get started with this social networking CMS. >>> More
OAuth: Token-Based Authorization for the Social Networking Age

as seen on Internet.com - Search for 'Internet.com'
The OAuth token-based authorization system allows users to grant third-party access to their resources without sharing their usernames and passwords. It's perfect for the age of data scattered across many social networking sites. >>> More
OAuth: Token-Based Authorization for the Social Networking Age

as seen on Internet.com - Search for 'Internet.com'
The OAuth token-based authorization system allows users to grant third-party access to their resources without sharing their usernames and passwords. It's perfect for the age of data scattered across many social networking sites. >>> More

Related posts about iscsi

Removing an iSCSI Target - iSCSI initiator 2.0 on Windows Server 2003 R2

as seen on Server Fault - Search for 'Server Fault'
For the life of me I cannot figure out how to remove an iSCSI target (Dell Equallogic SAN) from a Windows Server 2003 box. The volume shows up in Windows as drive letter Y:\ Using the iSCSI initiator, I can remove the Target Portal, but cannot remove the Target itself. Can someone give me some… >>> More
AIX: iscsi volumes disappear after reboot

as seen on Server Fault - Search for 'Server Fault'
We have an IBM P505 AIX box, with two internal disks and a defined iSCSI volume. The iSCSI volume is defined in it's own volume group, and is connected to an IBM iSCSI DS3300 disk array via the secondary onboard ethernet port (ie, we're not using a dedicated HBA, we're using the second onboard ethernet… >>> More
How to connect SAN from CentOS through two iSCSI Targets

as seen on Server Fault - Search for 'Server Fault'
I had asked the similar question before. This time I want to use subnet for two iSCSI Targets, hence I start a new question. I have an old Promise VTrak M500i SAN Server. It comes with 2 iSCSI ports. I want to connect to two LUNs on the SAN server through two separate Targets from CentOS 5.7 64bits… >>> More
Can single ESXi host make use of two separete iSCSI box?

as seen on Server Fault - Search for 'Server Fault'
Hi! I have problem with using multiply iSCSI targets with single ESXi host (in my case they are two FreeNAS hosts, but I suspect that this problem will occur with any two iSCSI box of that same type/model). If I configure two FreeNAS hosts as iSCSI targets (say iSCSI A and iSCSI B), then I can use… >>> More
Problems with 2 ISCSI connections esxi 3.5

as seen on Server Fault - Search for 'Server Fault'
I am running a dell poweredge 1950 with 4 nic cards. 1 is bonded to SAN #1 on 192.168.90.xx. The second SAN is on a separate network - 192.168.7.xx The network adapter can view the ip range of the san and the NIC can be pinged from 192.168.7.xx range. vswitch1 and vswitch2 are configured identically… >>> More