Monthly Archives

Articles indexed in December 2010

Page 359/366 | < Previous Page | 355 356 357 358 359 360 361 362 363 364 365 366  | Next Page >

  • MacMini transmit rate stuck at 11, every other device can connect at full 54Mbit/s?

    - by chum of chance
    I have a MacMini circa 2007 that's getting very low transmit rates via wifi, 8-11. I have other devices that are getting full 54, including a MacBook Air. With everything else off, the MacMini doesn't want to seem to go any faster. Since it has been previously connected to ethernet its entire life, I was wondering if there were some settings I can change to speed up the connection. Option-clicking the network icon gives this read out: PHY Mode: 802.11g Channel: 1 (2.4 Ghz) Security: WPA2 Personal RSSI: -73 Transmit Rate: 11 My new MacBook Air has the following readout: PHY Mode: 802.11n Channel: 1 (2.4 Ghz) Security: WPA2 Personal RSSI: -66 Transmit Rate: 79 Both have full bars and the wireless router is in the same room to eliminate any obstructions from the equation. Could the MacMini be connecting at an older protocol, like 802.11b and be reporting erroneously that it is connected at 802.11g? This would explain why I haven't seen a transmit rate above 11. Any further trouble shooting I can try before buying a new USB 802.11n device? The WiFi router is a DLink DIR-615. I can see other devices, and none, even the other g connected devices, are getting below 30-40 MBit/s. What's going on here?

    Read the article

  • Is there a clean way to obtain exclusive access to a physical partition under Windows?

    - by zneak
    Hey guys, I'm trying, under Windows 7, to run a virtual machine with VMWare Player from an OS installed on a physical partition. However, when I boot the virtual machine, VMWare Player says that it couldn't access the physical drive for writing. This seems to be a generally acknowledged problem in the VMWare community, as Windows Vista introduced a compelling new security feature that makes it impossible to write to a raw drive without obtaining exclusive access to it first. I have googled the issue and found a few workarounds. However, the clean ones seem to only work on whole physical disks, and not on partitions. So I would be left with the dirty solution. In short, it meddles with the MBR to erase any trace of the partitions to use, makes Windows forget about them, then restores the MBR so we can launch the VM. I'm not sure I want to do that. Is there a way to let VMWare acquire exclusive access to the partition without requiring me to nuke it away? What I'd be looking for, I suppose, is a way to put just partitions offline instead of whole physical drives.

    Read the article

  • How can I connect my HP Photosmart C3100 printer in 10.04 (regression from 9.x)

    - by Brian
    My printer was working under 9.x. It is a an HP Photosmart C3100 series. When I open Admin-Printing no local printers are found. I try to add via Other (My local choices are Serial and other). I have tried many url's - ipp://localhost:631/ipp, http://localhost/ipp, localhost, 127.0.0.1, etc... None have worked. Under the networked I have tried JetDirect, using localhost and 127.0.0.1 and port 631. I have tried many options under IPP with different variants in the host trying to verify a printer. No luck .I tried LPD/LPR with localhost and tried the probe. no luck. I tried the cups admin via localhost:631 and that didn't work. On the old version its simply found the local printer, I might have picked the driver, I can't remember but it was the photosmart c3100 series that was working.I just can't get 10.04 to print.

    Read the article

  • What is the right way to Windows 7/Ubuntu 10.10 Dual-Triple Boot Partitioning for Laptop OEM?

    - by Denja
    Hi Linux Community, I find my self struggling with the ever slow and buggy windoze OS once again. It's Time to change with the Ubuntu 10.10 64bit as a really faster Operating System. My Hard Disk laptop as a RECOVERY and HP_TOOLS partition they are both Primary. I Have the System Recovery DVD for Windows 64bit should anything happen. Here's the layout I used with windows before: * (C:) Windows 7 system partition NTFS - 284,89GB (Primary,Boot,Pagefile,Dump) * HP_TOOLS system partition FAT32 - 99MB (Primary) * (D:) RECOVERY partition NTFS - 12,90GB (Primary) * SYSTEM partition NTFS 199MB (Primary) Here's the layout I want to make based on your answers * (C:) Windows 7 system partition NTFS - 60GB (Primary) (sda1) * (D:) Windows DATA partition (user files) NTFS - 120GB(Primary)(sda2);wanna share with Linux * Linux root Ext4 - 100GB (Primary)(sda3) (Ubuntu 10.10 64bit) * Linux swap swap- RAM size, 3GB (sda4) * Linux root Ext3- 15,9GB (Extended)(sda5) (OpenSuse or Puppy) Here is my New Ubuntu 10.10 64bit layout in use now: * SYSTEM partition NTFS 199MB (Primary) (sda1) **Partition 1 does not end on cylinder boundary.(?)** * (C:) Windows 7 system partition NTFS - 90GB (Primary) (sda2) * (D:) Windows 7 RECOVERY partition NTFS - 12,90GB (Primary) (sda3) * Linux system partition EXTENDED - 195GB (Logical) * Linux root Ext4- 10GB (Extended) (sda5) * Linux home Ext3- 185GB (Extended) (sda6) I didn't know if I could wipe all previous partitions when i installed Ubuntu because of the RECOVERY partition so I just made the space for my extended partition by deleting the HP_TOOLS (Fat32). By doing this I managed to make and successfully install Ubuntu 64 but I couldn't actually make the partition for the swap or a third Linux OS. Question 1: What is the right way to Windows 7/Ubuntu 10.10 Dual-Triple Boot Partitioning for Laptop OEM?? Thank you in advance for your advises and suggestions and Happy New Year to All!!

    Read the article

  • Error trying to run rails server

    - by David87
    I am trying to get a basic Rails application to run on my Mac OS X 10.6.5. I created a new app called demo (rails new demo), then went into the demo directory and tried to start the app with rails server. Here is the error message I received: "/Users/dpetrovi/.gem/ruby/1.8/gems/sqlite3-ruby-1.3.2/lib/sqlite3/sqlite3_native.bundle: [BUG] Segmentation fault ruby 1.8.7 (2010-12-23 patchlevel 330) [i686-darwin10] Abort trap" I checked bundle install in the demo folder: "Using rake (0.8.7) Using abstract (1.0.0) Using activesupport (3.0.3) Using builder (2.1.2) Using i18n (0.5.0) Using activemodel (3.0.3) Using erubis (2.6.6) Using rack (1.2.1) Using rack-mount (0.6.13) Using rack-test (0.5.6) Using tzinfo (0.3.23) Using actionpack (3.0.3) Using mime-types (1.16) Using polyglot (0.3.1) Using treetop (1.4.9) Using mail (2.2.13) Using actionmailer (3.0.3) Using arel (2.0.6) Using activerecord (3.0.3) Using activeresource (3.0.3) Using bundler (1.0.7) Using thor (0.14.6) Using railties (3.0.3) Using rails (3.0.3) Using sqlite3-ruby (1.3.2) Your bundle is complete! Use bundle show [gemname] to see where a bundled gem is installed." Ruby, RubyGems, and sqlite3 were installed using MacPorts. Then I used gem to try to install the sqlite3-ruby interface. (sudo gem install sqlite3-ruby). Here is where I first noticed something could be off: "Successfully installed sqlite3-ruby-1.3.2 1 gem installed Installing ri documentation for sqlite3-ruby-1.3.2... No definition for libversion Enclosing class/module 'mSqlite3' for class Statement not known Installing RDoc documentation for sqlite3-ruby-1.3.2... No definition for libversion Enclosing class/module 'mSqlite3' for class Statement not known " I had rails running well on my system a few months ago, so I figured maybe I had some duplicates and it was trying to use the wrong one. I ran: "for cmd in ruby irb gem rake; do which $cmd; done" and got: "/opt/local/bin/ruby /opt/local/bin/irb /opt/local/bin/gem /opt/local/bin/rake" Checking where sqlite3 also gets me: "/opt/local/bin/sqlite3" so they all seem to be in the right place. Obviously /opt/local/bin is in my system path. If I check gems server, it shows that I have installed sqlite3-ruby 1.3.2 gem. Not sure what the problem could be? I am using ruby 1.8.7 (2010-12-23 patchlevel 330) [i686-darwin10]. Macports claims this is the latest (although ive seen 1.9.1) One more thing-- in irb, I tried to check which version of sqlite3 my sqlite3-ruby is bound to, but I can only get this far: ":irb(main):001:0 require 'rubygems' = true irb(main):002:0 require 'sqlite3' /Users/dpetrovi/.gem/ruby/1.8/gems/sqlite3-ruby-1.3.2/lib/sqlite3/sqlite3_native.bundle: [BUG] Segmentation fault ruby 1.8.7 (2010-12-23 patchlevel 330) [i686-darwin10] Abort trap" Any suggestions? Im hoping I overlooked something obvious. Thanks

    Read the article

  • Will this LINQ-TO-SQL query fetch all records from the table ?

    - by Puneet Dudeja
    public long GetNewCRN() { return ((from c in DataContext.GetTable<Cust_Master>() select c.CUSTSERH_CRN).Max() + 1); } Will this Linq to Sql query fetch all records from the table first and then select the maximum of the column ? If yes, then isn't it a bad idea using linq to sql instead of normal SqlCommand ? Or is there any other way of doing it in linq to sql ? When I attach Console.Out, I see nothing(command prompt does not even open). But when I include following:- context.Log = new System.IO.StreamWriter("d:\\abcd.txt"); I get an error, that "The process can not access the file because it is being used by another process" and that process is "w3wp.exe". How can I see the sql commands being executed by DataContext then ?

    Read the article

  • Visual Studio crashes consistently on web-related projects

    - by Traveling Tech Guy
    Hi, I have a brand new VS2010 installed on a Win2008R2 machine. I started getting this error when debugging a WCF service project: "Attempted to read or write protected memory. This is often an indication that other memory is corrupt." When I started developing a web site a week later, this became consistent - I can't debug it. The stack dump reads: at Microsoft.VisualStudio.WebHost.Host.ProcessRequest(Connection conn) at Microsoft.VisualStudio.WebHost.Server.OnSocketAccept(Object acceptedSocket) at System.Threading.QueueUserWorkItemCallback.WaitCallback_Context(Object state) at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state, Boolean ignoreSyncCtx) at System.Threading.QueueUserWorkItemCallback.System.Threading.IThreadPoolWorkItem.ExecuteWorkItem() at System.Threading.ThreadPoolWorkQueue.Dispatch() at System.Threading._ThreadPoolWaitCallback.PerformWaitCallback() I tried searching online, and some recommend turning off the "Suppress JIT Optimizations" in the Debugging options - this dos not seem to make a difference. Clearly the problem is with the built in web server. But am I doing something wrong? Is there something I can do? Or is this a known bug? Thanks for your time, Guy Update 12/31: Today I tried using CassiniDev as a replacement to the original VS2010 WebServer - exact same result. My suspicion is that there's some internal conflict between VS2010, Windows Server 2008R2 and maybe the fact that it's a 64 bit OS. I switched to using IIS as my debug server - and that seems to work, with some annoying side effects. My conclusion: do not use a 64 bit server system as your dev machine. Develop on 32bit - deploy to 64bit. Side conclusion: there are some scenarios Microsoft's QA doesn't test.

    Read the article

  • Open a buffer as a vertical split in VIM

    - by alfredodeza
    If you are editing a file in VIM and then you need to open an existing buffer (e.g. from your buffer list: :buffers) how can you open it in a vertical split? I know that you already can open it with a normal split like: :sbuffer N Wehere N is the buffer number you want, however, the above opens that N buffer horizontally, not vertically. I'm also aware that you can change the window placement after opening and have a Vertical Split like so: Ctrl-W H Ctrl-W L Which will vertically split the window to the right or the left. It seems to me that if there is a sbuffer there should be a vsbuffer but that doesn't exist (not that I am aware of) Also, please note that I am not looking for a plugin to solve this question. I know about a wealth of plugins that will allow you to do this. I am sure I might be missing something that is already there. EDIT: In the best spirit of collaboration, I have created a simple Function with a Mapping if someone else stumbles across this issue and do not want to install a plugin: Function: " Vertical Split Buffer Function function VerticalSplitBuffer(buffer) execute "vert belowright sb" a:buffer endfunction Mapping: " Vertical Split Buffer Mapping command -nargs=1 Vbuffer call VerticalSplitBuffer(<f-args>) This accomplishes the task of opening a buffer in a right split, so for buffer 1, you would call it like: :Vbuffer 1

    Read the article

  • Convert octet string to human readable

    - by Michael Lang
    Using the pysnmp framework i get some values doing a snmp walk. Unfortunately for the oid 1.3.6.1.21.69.1.5.8.1.2 (DOCS-CABLE-DEVICE-MIB) i get a weird result which i cant correctly print here since it contains ascii chars like BEL ACK When doing a repr i get: OctetString('\x07\xd8\t\x17\x03\x184\x00') But the output should look like: 2008-9-23,3:24:52.0 the format is called "DateAndTime". How can i translate the OctetString output to a "human readable" date/time ?

    Read the article

  • Help with a Join in Rails 3

    - by Adam Albrecht
    I have the following models: class Event < ActiveRecord::Base has_many :action_items end class ActionItem < ActiveRecord::Base belongs_to :event belongs_to :action_item_type end class ActionItemType < ActiveRecord::Base has_many :action_items end And what I want to do is, for a given event, find all the action items that have an action item type with a name of "foo" (for example). So I think the SQL would go something like this: SELECT * FROM action_items a INNER JOIN action_item_types t ON a.action_item_type_id = t.id WHERE a.event_id = 1 AND t.name = "foo" Can anybody help me translate this into a nice active record query? (Rails 3 - Arel) Thanks!

    Read the article

  • Are parametrized calls/sanitization/escaping characters necessary for hashed password fields in SQL queries?

    - by Computerish
    When writing a login system for a website, it is standard to use some combination of parameterized calls, sanitizing the user input, and/or escaping special characters to prevent SQL injection attacks. Any good login system, however, should also hash (and possibly salt) every password before it goes into an SQL query, so is it still necessary to worry about SQL injection attacks in passwords? Doesn't a hash completely eliminate any possibility of an SQL injection attack on its own?

    Read the article

  • How to set default view in OpenLayers, WITHOUT restricting bounds?

    - by Jenny
    Based on samples, I can see that you can set a default view in OpenLayers by saying something along the lines of: var bounds = new OpenLayers.Bounds(-125, 25, -65, 50); var map = new OpenLayers.Map('map', {restrictedExtent: bounds }); However, this also (as the name implies), restricts me to be able to ONLY navigate within these bounds. I can zoom out and see things outside of these bounds, but I can't then zoom back onto them, or scroll to them. I've tried not having any restrictedExtent (or making it the entire map), but then I can't get it to focus on the area I want. I tried using: map.setCenter(new OpenLayers.LonLat(0,0), 3); console.log(map.getCenter()); To set the zoom and the center...but it doesn't seem to do ANYTHING, other than set the variable "center" which I can then read from map.getCenter() (if I don't set it, it's null, if I do set it, I can see it...but the map itself stays fully extended and it's center doesn't seem to change at all...) The Map layer I am using is: OpenLayers.Layer.OSM.Mapnik with displayOutsideMaxExtent set to true... I'm really at a loss here. My goal is to have a default region of the world zoomed in to and in view (such as the United States), with the option of viewers being able to go outside the default to view things.

    Read the article

  • What could be the Java successor Oracle wants to invest in?

    - by deamon
    I've read that Oracle wants to invest into another language than Java: "On the other hand, Oracle has been particularly supportive of alternative JVM languages. Adam Messinger ( http://www.linkedin.com/in/adammessinger ) was pretty blunt at the JVM Languages Summit this year about Java the language reaching it's logical end and how Oracle is looking for a 'higher level' language to 'put significant investment into.'" But what language could be the one Oracle wants to invest in? Is there another candidate than Scala?

    Read the article

  • Slowing process creation under Java?

    - by oconnor0
    I have a single, large heap (up to 240GB, though in the 20-40GB range for most of this phase of execution) JVM [1] running under Linux [2] on a server with 24 cores. We have tens of thousands of objects that have to be processed by an external executable & then load the data created by those executables back into the JVM. Each executable produces about half a megabyte of data (on disk) that when read right in, after the process finishes, is, of course, larger. Our first implementation was to have each executable handle only a single object. This involved the spawning of twice as many executables as we had objects (since we called a shell script that called the executable). Our CPU utilization would start off high, but not necessarily 100%, and slowly worsen. As we began measuring to see what was happening we noticed that the process creation time [3] continually slows. While starting at sub-second times it would eventually grow to take a minute or more. The actual processing done by the executable usually takes less than 10 seconds. Next we changed the executable to take a list of objects to process in an attempt to reduce the number of processes created. With batch sizes of a few hundred (~1% of our current sample size), the process creation times start out around 2 seconds & grow to around 5-6 seconds. Basically, why is it taking so long to create these processes as execution continues? [1] Oracle JDK 1.6.0_22 [2] Red Hat Enterprise Linux Advanced Platform 5.3, Linux kernel 2.6.18-194.26.1.el5 #1 SMP [3] Creation of the ProcessBuilder object, redirecting the error stream, and starting it.

    Read the article

  • Find the order among tasks in a company by using prolog?

    - by Cem
    First of all,I wish a happy new year for everyone.I searched more and worked a lot but I could not solve this question.I am quite a new in prolog and I must do this homework. In my homework,the question is like this: Write a prolog program that determines a valid order for the tasks to be carried out in a company. The prolog program will consist of a set of "before" predicates which denotes the order between task pairs. Here is an example; before(a,b). before(a,e). before(d,c). before(b,c). before(c,e). Here, task a should be carried before tasks b and e, d before c and so on. Hence a valid ordering of the tasks would be [a, b, d, c, e]. The order predicate in your program will be queried as follows. ?- order([a,b,c,d,e],X). X = [a, b, d, c, e] ; X = [a, d, b, c, e] ; X = [d, a, b, c, e] ; false. Hint: Try to generate different orders for the tasks (permutation) and then check if the order is consistent with the "before" relationships given. Even if you can generate a single valid order, you will get reasonable partial credits.

    Read the article

  • Text + randomchar dosn't work [JavaScript]

    - by user558773
    <script> function makeid() { var text = "var text = document.write(lastNumber);"; var possible = "*+-/"; for( var i=0; i < 1; i++ ) document.write(lastNumber + possible.charAt(Math.floor(Math.random() * possible.length)); return text; } document.write(makeid(1))</script> How do i make this to type for ex: 23* 45- 13/ and so on. What is wrong? It just show me 2 numbers and no char after.

    Read the article

  • why doesnt' nhibernate support this syntax ??

    - by ooo
    i have the following query and its failing in Nhibernate 3 LINQ witha a "Non supported" exception. My DB tables are: VacationRequest (id, personId) VacationRequestDate (id, vacationRequestId) Person (id, FirstName, LastName) My Entities are: VacationRequest (Person, IList) VacationRequestDate (VacationRequest, Date) Here is the query that is getting a "Non supported" Exception Session.Query<VacationRequestDate>().Where(r => people.Contains(r.VacationRequest.Person, new PersonComparer())).Fetch(r=>r.VacationRequest).ToList(); is there a better way to write this that would be supported in Nhibernate? fyi . .the PersonComparer just compared person.Id

    Read the article

  • FullCalendar displaying last weeks events below this weeks events

    - by Brian
    I am developing an application to manage an On-Call calendar, using FullCalendar to render it. Most events are 1 week long, starting at 8:00 AM Tuesday and ending the following Tuesday at 8:00 AM. Another event, presumably with a different person on-call, will follow that event. During a hallway usability test, someone commented that the month calendar view was difficult to read because the previous weeks event is not at the top of the stack, instead rendering below the event that starts during that week. When being viewed, the eye perceives that it should go down 1 line to view the remaining timeline because the event from last week is there, instead of moving down to the following week. I investigated what I believe to be the problem: function segCmp(a, b) { return (b.msLength - a.msLength) * 100 + (a.event.start - b.event.start); } sorts the events for a row, but uses the length of the event in the calculation. Since the current week's event will have a longer duration, it always get sorted to the top. To test, I changed the start dates to Wednesday so the durations are closer. This cause the events to render how I would expect, with last weeks events at the top and this weeks at the bottom. I thought that if one of the events in the compare doesn't start that week, then it should only be compared based on the start times. I modified the function to be: function segCmp(a, b) { if (a.isStart == false || b.isStart == false) { return (a.event.start - b.event.start); } return (b.msLength - a.msLength) * 100 + (a.event.start - b.event.start); } This solved my problem, and the rendering now looks good - and passes the hallway test. What I don't know is if this would have an impact in other areas. I have taken a look at the other views (month, week, day) and they all seem to be rendering properly as well. I am just not familiar with FullCalendar enough to file a bug or feature request on this, or if this would even be considered a bug. I am wondering if what I modified is correct, or if it is not what a better modification would be to fix this issue. Thanks! Below I have the json results for what should be displayed: [{"title":"Person 1 - OnCall (OSS On Call)","id":12,"allDay":false,"start":"2010-11-30T15:00:00.0000000Z","end":"2010-12-07T15:00:00.0000000Z","editable":false,"className":"fc-event-title-calendar","url":"/TimeManagement/Edit/12"}, {"title":"Person 2 - OnCall (OSS On Call)","id":13,"allDay":false,"start":"2010-12-07T15:00:00.0000000Z","end":"2010-12-14T15:00:00.0000000Z","editable":false,"className":"fc-event-title-calendar","url":"/TimeManagement/Edit/13"}, {"title":"Person 3 - OnCall (OSS On Call)","id":14,"allDay":false,"start":"2010-12-14T15:00:00.0000000Z","end":"2010-12-21T15:00:00.0000000Z","editable":false,"className":"fc-event-title-calendar","url":"/TimeManagement/Edit/14"}, {"title":"Person 4 - OnCall (OSS On Call)","id":15,"allDay":false,"start":"2010-12-21T15:00:00.0000000Z","end":"2010-12-28T15:00:00.0000000Z","editable":false,"className":"fc-event-title-calendar","url":"/TimeManagement/Edit/15"}, {"title":"Person 5 - OnCall (OSS On Call)","id":16,"allDay":false,"start":"2010-12-28T15:00:00.0000000Z","end":"2011-01-04T15:00:00.0000000Z","editable":false,"className":"fc-event-title-calendar","url":"/TimeManagement/Edit/16"}, {"title":"Person 6 - OnCall (OSS On Call)","id":17,"allDay":false,"start":"2011-01-04T15:00:00.0000000Z","end":"2011-01-11T15:00:00.0000000Z","editable":false,"className":"fc-event-title-calendar","url":"/TimeManagement/Edit/17"}, {"title":"Christmas","id":2,"allDay":true,"start":"2010-12-25T07:00:00.0000000Z","end":null,"editable":false,"className":"fc-event-title-calendar","url":"/TimeManagement/Edit/2"}, {"title":"New Years Eve","id":3,"allDay":true,"start":"2010-12-31T07:00:00.0000000Z","end":null,"editable":false,"className":"fc-event-title-calendar","url":"/TimeManagement/Edit/3"}, {"title":"New Years Day","id":4,"allDay":true,"start":"2011-01-01T07:00:00.0000000Z","end":null,"editable":false,"className":"fc-event-title-calendar","url":"/TimeManagement/Edit/4"}]

    Read the article

  • Custom Tile Layer Problem

    - by Myra
    Hi,I'm currently implementing logic on custom tile layers via OpenLayers function getTiles() { var res = this.map.getResolution(); var x = Math.round((bounds.left - this.maxExtent.left) / (res * this.tileSize.w)); var y = Math.round((this.maxExtent.top - bounds.top) / (res * this.tileSize.h)); var z = this.map.getZoom(); return ......; } What I need to is to carry this code in Google API v3. As I searched documentation I found this code to work with: var customtile = new google.maps.ImageMapType({ getTileUrl: function (coord, zoom) { .... .... } Unfortonately,I cannot convert logic in OpenLayers code to Google. As I know resolution is 180 * tileSize.w / Math.pow(2, zoom) //where tileSize is 256x256 Since Google projection is same with my tiles WGS84 boundary should be -180,-90,90,180 I need to calculate to extent coordinates,but in function getTileUrl,there are two arguments.One of which is zoom,but the other coord is some x,y pair which I dont understand what that is.What is that exactly ? How can I generalize formula for calculating tile numbers in Google Maps? Thank you Myra

    Read the article

  • Best way to add an extra (nested) form in the middle of a tabbed form

    - by Scharrels
    I've got a web application, consisting mainly of a big form with information. The form is split into multiple tabs, to make it more readable for the user: <form> <div id="tabs"> <ul> <li><a href="#tab1">Tab1</a></li> <li><a href="#tab2">Tab2</a></li> </ul> <div id="tab1">A big table with a lot of input rows</div> <div id="tab2">A big table with a lot of input rows</div> </div> </form> The form is dynamically extended (extra rows are added to the tables). Every 10 seconds the form is serialized and synchronized with the server. I now want to add an interactive form on one of the tabs: when a user enters a name in a field, this information is sent to the server and an id associated with that name is returned. This id is used as an identifier for some dynamically added form fields. A quick sketchup of such a page would look like this: <form action="bigform.php"> <div id="tabs"> <ul> <li><a href="#tab1">Tab1</a></li> <li><a href="#tab2">Tab2</a></li> </ul> <div id="tab1">A big table with a lot of input rows</div> <div id="tab2"> <div class="associatedinfo"> <p>Information for Joe</p> <ul> <li><input name="associated[26][]" /></li> <li><input name="associated[26][]" /></li> </ul> </div> <div class="associatedinfo"> <p>Information for Jill</p> <ul> <li><input name="associated[12][]" /></li> <li><input name="associated[12][]" /></li> </ul> </div> <div id="newperson"> <form action="newform.php"> <p>Add another person:</p> <input name="extra" /><input type="submit" value="Add" /> </form> </div> </div> </div> </form> The above will not work: nested forms are not allowed in HTML. However, I really need to display the form on that tab: it's part of the functionality of that page. I also want the behaviour of a separate form: when the user hits return in the form field, the "Add" submit button is pressed and a submit action is triggered on the partial form. What is the best way to solve this problem?

    Read the article

  • Is daisy chaining xslt an accepted practice?

    - by Stephen
    I have a situation where I think I need to daisy chain my xslt transformation (i.e. that output of one xslt transform being input into another). The first transform is rather complex with lots of xsl:choice and ancestor xpaths. My thought is to transform the xml into xml that can then be easily transformed to html. My question is 'Is this standard practice or am I missing something?' Thanks in advance. Stephen

    Read the article

  • JSONResult to String

    - by Dustin Laine
    I have a JsonResult that is working fine, and returning JSON from some POCO's. I want to save the JSON as a string in a DB. public JsonResult GetJSON() { JsonResult json = new JsonResult { Data = GetSomPocos() }; return json; } I need to audit the response, so I want to save the json into a DB. I am having trouble finding a way to get the JSON as a string. Any help is appreciated.

    Read the article

  • sql join question, how to select when value not in a set of values

    - by Elliott
    I have two tables, table1 and table2. Table1 is in a one to many relationship with table2 (one row in table1 maps to many rows in table2). There is a field in table2 called code. If none of the values of code in table2 equal some set of values (say 1, 2, and 3), I want to select the value in table1. I'm not sure how to write this kind of join. Assume the primary key in table1 is called id and the foreign key to which it maps is called did. Can you tell me how to write this kind of join? Thanks, Elliott

    Read the article

  • Best practice for making code portable for domains, subdomains or directores

    - by Duopixel
    I recently coded something where it wasn't known if the end code would reside in a subdomain (http://user.domain.com/) or in a subdomain (http://domain.com/user), and I was lost as to the best practice for these unknown scenarios. I could thinks of a couple: Use absolute paths (/css/styles.css) and modrewrite if it ends up being /user Have a settings file and declare a variable with the path (<? php echo $domain . "/css/styles" ?>) Use relative paths (../css/styles.css). What is the best way to handle this?

    Read the article

  • Why is this javascript function so slow on Firefox?

    - by macrael
    This function was adapted from the website: http://eriwen.com/javascript/measure-ems-for-layout/ function getEmSize(el) { var tempDiv = document.createElement("div"); tempDiv.style.height = "1em"; el.appendChild(tempDiv); var emSize = tempDiv.offsetHeight; el.removeChild(tempDiv); return emSize; } I am running this function as part of another function on window.resize, and it is causing performance problems on Firefox 3.6 that do not exist on current Safari or Chrome. Firefox's profiler says I'm spending the most time in this function and I'm curious as to why that is. Is there a way to get the em size in javascript without doing all this work? I would like to recalculate the size on resize incase the user has changed it.

    Read the article

< Previous Page | 355 356 357 358 359 360 361 362 363 364 365 366  | Next Page >