Recently I've set up a new Ubuntu Server 10.04 and noticed my UDP server is no longer able
to see any multicast data sent to the interface, even after joining the multicast group. I've got the exact same set up on two other Ubuntu 8.04.4 LTS machines and there is no problem receiving data after joining the same multicast group.
The ethernet card is a Broadcom netXtreme II BCM5709 and the driver used is:
b $ ethtool -i eth1
driver: bnx2
version: 2.0.2
firmware-version: 5.0.11 NCSI 2.0.5
bus-info: 0000:01:00.1
I'm using smcroute to manage my multicast registrations.
b$ smcroute -d
b$ smcroute -j eth1 233.37.54.71
After joining the group ip maddr shows the newly added registration.
b$ ip maddr
1: lo
inet 224.0.0.1
inet6 ff02::1
2: eth0
link 33:33:ff:40:c6:ad
link 01:00:5e:00:00:01
link 33:33:00:00:00:01
inet 224.0.0.1
inet6 ff02::1:ff40:c6ad
inet6 ff02::1
3: eth1
link 01:00:5e:25:36:47
link 01:00:5e:25:36:3e
link 01:00:5e:25:36:3d
link 33:33:ff:40:c6:af
link 01:00:5e:00:00:01
link 33:33:00:00:00:01
inet 233.37.54.71 <------- McastGroup.
inet 224.0.0.1
inet6 ff02::1:ff40:c6af
inet6 ff02::1
So far so good, I can see that I'm receiving data for this multicast group.
b$ sudo tcpdump -i eth1 -s 65534 host 233.37.54.71
tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
listening on eth1, link-type EN10MB (Ethernet), capture size 65534 bytes
09:30:09.924337 IP 192.164.1.120.58848 > 233.37.54.71.15572: UDP, length 212
09:30:09.947547 IP 192.164.1.120.58848 > 233.37.54.71.15572: UDP, length 212
09:30:10.108378 IP 192.164.1.120.58866 > 233.37.54.71.15574: UDP, length 268
09:30:10.196841 IP 192.164.1.120.58848 > 233.37.54.71.15572: UDP, length 212
...
I can also confirm that the interface is receiving mcast packets.
b $ ethtool -S eth1 | grep mcast_pack
rx_mcast_packets: 103998
tx_mcast_packets: 33
Now here's the problem. When I try to capture the traffic using a simple ruby UDP server I receive zero data! Here's a simple server that reads data send on port 15572 and prints
the first two characters. This works on the two 8.04.4 Ubuntu Servers, but not the 10.04 server.
require 'socket'
s = UDPSocket.new
s.bind("", 15572)
5.times do
text, sender = s.recvfrom(2)
puts text
end
If I send a UDP packet crafted in ruby to localhost, the server receives it and prints out the first two characters. So I know that the server above is working correctly.
irb(main):001:0> require 'socket'
=> true
irb(main):002:0> s = UDPSocket.new
=> #<UDPSocket:0x7f3ccd6615f0>
irb(main):003:0> s.send("I2 XXX", 0, 'localhost', 15572)
When I check the protocol statistics I see that InMcastPkts is not increasing. While on
the other 8.04 servers, on the same network, received a few thousands packets in 10 seconds.
b $ netstat -sgu ; sleep 10 ; netstat -sgu
IcmpMsg:
InType3: 11
OutType3: 11
Udp:
446 packets received
4 packets to unknown port received.
0 packet receive errors
461 packets sent
UdpLite:
IpExt:
InMcastPkts: 4654 <--------- Same as below
OutMcastPkts: 3426
InBcastPkts: 9854
InOctets: -1691733021
OutOctets: 51187936
InMcastOctets: 145207
OutMcastOctets: 109680
InBcastOctets: 1246341
IcmpMsg:
InType3: 11
OutType3: 11
Udp:
446 packets received
4 packets to unknown port received.
0 packet receive errors
461 packets sent
UdpLite:
IpExt:
InMcastPkts: 4656 <-------------- Same as above
OutMcastPkts: 3427
InBcastPkts: 9854
InOctets: -1690886265
OutOctets: 51188788
InMcastOctets: 145267
OutMcastOctets: 109712
InBcastOctets: 1246341
If I try forcing the interface into promisc mode nothing changes.
At this point I'm stuck. I've confirmed the kernel config has multicast enabled. Perhaps there are other config options I should be checking?
b $ grep CONFIG_IP_MULTICAST /boot/config-2.6.32-23-server
CONFIG_IP_MULTICAST=y
Any thoughts on where to go from here?
