Search Results

Search found 3935 results on 158 pages for 'garreth 00'.

Page 100/158 | < Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >

• Getting a Conexant CX23885 TV Capture Card working

  - by Benny

  I'm new to Linux, and am trying to get my Capture Card working on 11.04. The only command that I know to run to find out any information is lspci, which tells me that I have 02:00.0 Multimedia video controller: Conexant Systems, Inc. CX23885 PCI Video and Audio Decoder (rev 04) I've looked at using Me TV, but haven't worked out how to configure it for my card, or what I need to do to get it running. I'm not fussed on what software I use to run the Capture Card, but I've currently got only Me TV installed. Edit: When I run tvtime, I get the following errors: videoinput: Cannot open capture device /dev/video0: No such file or directory mixer: find error: Success mixer: Can't open mixer default, mixer volume and mute unavailable. mixer: Can't open device default/Line, mixer volume and mute unavailable. Segmentation fault

  Read the article

• Ubuntu 12.10 64bit fresh install, wireless issue!

  - by Dave

  Just installed a fresh Ubuntu 12.10 64bit on my laptop, run the update manager, restarted and suddenly I can't use my wifi anymore. Ubuntu software center installed automatically the wifi additional driver as you can see in my screenshot. If I mark the option "Do not use the device" and apply changes, restarting Ubuntu my wifi is back and I can use it. If I run iwconfig my terminal is showing this Now if I use Ubuntu for more than 20 minutes surfing the web my wifi it keeps to be connected but I don't receive any signal from it. Any page I try to open it simply don't open (just waiting icon). If I disconnect my wifi and connect it again, same issue, it doesn't work. The only way to make it work again is to restart Ubuntu. And the same story it happens again after aprox. 20, 30 minutes. WIFI device details: 03:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) Thanks, Dave

  Read the article

• /etc/X11/xorg.conf doesn't exist?

  - by BBetances

  I'm trying to get my video card properly setup to handle 3D acceleration. After searching a bit, I've come across a few howtos that tell me I need to edit my xorg.conf file. That file doesn't exist. X.org is installed by default, I'm sure, and I figured this video card would be widely supported. 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 09) Any ideas on how I can get this to work properly and play Starcraft II? Or any game for that matter? No resolution problems or anything, just no 3D rendering.

  Read the article

• How to make "xrandr" work with GMA500?

  - by Nwbie

  Is it error at driver of graphic chip or Xorg or kernel? I am Asus T91mt with GMA500, Ubuntu 12.04.1. I would like too see only a notice of connection at least. A log of xrandr: $ lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation System Corporation System Controller Hub (SCH Poulcbo) Graphics Controller (rev 07) vp@vc:~$ xrandr --verbose xrandr: Failed to get size of gamma for output default Screen 0: minimum 1024 x 600, current 1024 x 600, maximum 1024 x 600 default connected 1024x600+0+0 (0x138) normal (normal) 0mm x 0mm Identifier: 0x137 Timestamp: 26863 Subpixel: unknown Clones: CRTC: 0 CRTCs: 0 Transform: 1.000000 0.000000 0.000000 0.000000 1.000000 0.000000 0.000000 0.000000 1.000000 filter: 1024x600 (0x138) 0.0MHz *current h: width 1024 start 0 end 0 total 1024 skew 0 clock 0.0KHz v: height 600 start 0 end 0 total 600 clock 0.0Hz vp@vc:~$ xrandr --prop xrandr: Failed to get size of gamma for output default Screen 0: minimum 1024 x 600, current 1024 x 600, maximum 1024 x 600 default connected 1024x600+0+0 0mm x 0mm 1024x600 0.0* vp@vc:~$ Please help, i am linux newbie and i am tired ;/

  Read the article

• Live Webcast, Dec. 6: Enterprise Clouds with Oracle VM

  - by Monica Kumar

  Mark your calendar! On Tuesday, Dec. 6th at 9am PT, we are hosting a live webcast with Oracle VM experts. Enterprise Clouds with Oracle VM Tuesday, Dec. 6 at 9 AM US PT The ability to create a cloud leveraging public or private infrastructure has been hampered by the lack of availability of practical, cost-effective choices for server virtualization. In this session, you will learn how Oracle provides a single virtualization solution for your entire infrastructure, and how Oracle Enterprise Manager and Oracle Virtual Assembly Builder help you manage Oracle Applications across the cloud. Also find out how virtualization was leveraged to transform IT for Oracle University and support more than 350,00 students in more than 40,000 classes each year. Those lessons have paved the path to private cloud computing inside Oracle. Speakers: Adam Hawley, Senior Director of Product Management, Oracle Dan Herrup, Principal Systems Engineer, Oracle Corporate Citizenship Register Now.

  Read the article

• No sound while playing multi-media in Ubuntu 12.04 for XPS15

  - by ved2254

  I have an XPS15 laptop, core i5, 8GB ram. Whenever I login my laptop I here the startup bongo sound. But my sound system just doesn't play anything, may it be a short audio clip or a movie. Output of lshw -c multimedia is : WARNING: you should run this program as super-user. *-multimedia description: Audio device product: 6 Series/C200 Series Chipset Family High Definition Audio Controller vendor: Intel Corporation physical id: 1b bus info: pci@0000:00:1b.0 version: 05 width: 64 bits clock: 33MHz capabilities: bus_master cap_list configuration: driver=snd_hda_intel latency=0 resources: irq:51 memory:f1c00000-f1c03fff WARNING: output may be incomplete or inaccurate, you should run this program as super-user. Headphones work just fine but there is no sound from the speakers. Is it a bug in multi-media players or ALSA?

  Read the article

• Is Query Performance different for different versions of SQL Server?

  - by Ronak Mathia

  I have fired 3 update queries in my stored procedure for 3 different tables. Each table contains almost 2,00,000 records and all records have to be updated. I am using indexing to speed up the performance. It quite working well with SQL Server 2008. stored procedure takes only 12 to 15 minutes to execute. (updates almost 1000 rows in 1 second in all three tables) But when I run same scenario with SQL Server 2008 R2 then stored procedure takes more time to complete execution. its about 55 to 60 minutes. (updates almost 100 rows in 1 second in all three tables). I couldn't find any reason or solution for that. I have also tested same scenario with SQL Server 2012. but result is same as above. Please give suggestions.

  Read the article

• Asus X552VL WI-FI Problem

  - by Mitkobg

  I have a problem with my Wireless on my laptop. When i did rfkill list: 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: asus-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 4: hci0: Bluetooth Soft blocked: no Hard blocked: no 5: phy1: Wireless LAN Soft blocked: no Hard blocked: yes itko@Mitko:~$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off mitko@Mitko:~$ lspci -nnk | grep -A2 0280 03:00.0 Network controller [0280]: Qualcomm Atheros AR9485 Wireless Network Adapter [168c:0032] (rev 01) Subsystem: AzureWave Device [1a3b:2c97] Kernel driver in use: ath9k mitko@Mitko:~$ lsmod | grep -e ath9k -e asus asus_nb_wmi 16990 0 asus_wmi 24191 1 asus_nb_wmi sparse_keymap 13948 1 asus_wmi ath9k 164164 0 ath9k_common 13551 1 ath9k ath9k_hw 453856 2 ath9k_common,ath9k ath 28698 3 ath9k_common,ath9k,ath9k_hw mac80211 626557 1 ath9k cfg80211 484040 4 wl,ath,ath9k,mac80211 wmi 19177 3 mxm_wmi,nouveau,asus_wmi video 19476 3 i915,nouveau,asus_wmi

  Read the article

• Cuda GeForce GT 555m (on Ubuntu 12.04 (Virtual Box))

  - by bobby

  I am running Ubuntu 12.04 in a Virtual Box as guest OS. Today I have tried to enable all functions of my graphic card under Ubuntu. But all my efforts were off the mark... because my experience with Linux is relatively small... I have tried the procedure which is described as in http://sn0v.wordpress.com/2012/05/11/installing-cuda-on-ubuntu-12-04/. Running the cuda-filepack always lead to an error like "installing driver canceled". Then I have tried to install the Bumblebee project. But I always get the error that the bumblebee daemon is not started. After some internet research I found a test-command lspci -nn | grep '[030[02]]' which results in 00:02.0 VGA compatible controller [0300]: InnoTek ... [80ee:beef] I've been trying to activate the card you for hours without success. Could you please give me some hints how to activate CUDA? Kind regards

  Read the article

• Oracle OpenWord 2012 - Managing Storage in the Cloud

  - by jwalker

  At Oracle OpenWorld this year attendees will get experience using the Sun ZFS Storage Appliance during the Managing Storage in the Cloud Hands-On-Lab. Using Sun ZFS Storage, we will be provisioning Oracle Enterprise Linux Virtual Machines and filesystem shares that can be used with Oracle Database. We will also be using Oracle DTrace Analytics to analyze I/O workloads and drill down to see how the storage is really being used. Hope you can join us! Session ID: HOL10034 Session Title: Managing Storage in the Cloud Speakers: Brian Haskins, Nagendran J, Paul Johnson, Karlheinz Vogel and Jim Walker Venue and Room: Marriott Marquis - Salon 14/15 Date and Times: Monday October 1 - 3:15-4:15PM, Tuesday October 2 - 5:00-6:00PM Oracle OpenWorld Storage Sessions

  Read the article

• How do I start xterm with a headless system?

  - by NeViXa

  I'm running Ubuntu 12.04 and I want to boot directly and headless in the terminal (no GUI). After that I want to startx to start a program in xterm. When I boot 'headed', everything is working like supposed to, but: - When I boot headless, startx is not working (no screens found) I already tried to change xorg.conf to below, but it didn't not work: Section "Device" Identifier "VNC Device" Driver "vesa" EndSection Section "Screen" Identifier "VNC Screen" Device "VNC Device" Monitor "VNC Monitor" SubSection "Display" Modes "1280x1024" EndSubSection EndSection Section "Monitor" Identifier "VNC Monitor" HorizSync 30-70 VertRefresh 50-75 EndSection How can I boot headless and still be able to run startx? ANSWER: Adding the BusID to the Devices section in the xorg.conf above, fixed the problem for me. BusID "PCI:1:00:1"

  Read the article

• Monitor not detected - low resolution only

  - by Jens

  I just installed Ubuntu 11.1 on my desktop pc. It was a clean install, no upgrading. I have a Samsung Syncmaster BX2450 connected to the PC. My problem is that I cannot make Ubuntu recognize my monitor - which is capable of more than 1024. I ran a shut down of lightdm, and ran sudo X -configure, but it gave me a "configuration failed". Nothing seems to work - any ideas? VESA: GF119 Board - 13100000 xx@xxx:~$ lspci -nn |grep VGA 02:00.0 VGA compatible controller [0300]: nVidia Corporation GT520 [GeForce GT520] [10de:1040] (rev a1) xx@xxx:~$ xrandr -q xrandr: Failed to get size of gamma for output default Screen 0: minimum 640 x 480, current 1024 x 768, maximum 1024 x 768 default connected 1024x768+0+0 0mm x 0mm 1024x768 61.0* 800x600 61.0 640x480 60.0

  Read the article

• Google I/O 2010 - Customizing Google Apps

  Google I/O 2010 - Customizing Google Apps Google I/O 2010 - Customizing Google Apps & integrating with customer environments Enterprise 201 Mike O'Brien, Matt Pruden (Appirio), Adam Graff (Genentech), Don Dodge (moderator) Learn from real life examples of customizing Google Apps to meet customer requirements. Hear from the customer (Genentech) and the System Integrator (Appirio). Explore integration issues and deployment best practices with people who have done it. Get your questions answered in this session. For all I/O 2010 sessions, please go to code.google.com From: GoogleDevelopers Views: 6 0 ratings Time: 52:00 More in Science & Technology

  Read the article

• Traktor Audio 2 DJ soundcard configuration

  - by Jaroslav

  I have a Traktor Audio 2 DJ USB sound card (the first version of what it's now called simply Traktor Audio 2) The problem in settings it only sees one output, when there should be two (I need that for Mixxx etc.) Also I want to be able set the sample rate to one of these: 44.1, 48, 88.2, 96 kHz or at least check which one is set. Additionally if possible setting the latency would be an advantage. Some info: $ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: HDMI [HDA ATI HDMI], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: TraktorAudio2 [Traktor Audio 2], device 0: Traktor Audio 2 [Traktor Audio 2] Subdevices: 1/2 Subdevice #0: subdevice #0 Subdevice #1: subdevice #1 $ cat /proc/asound/cards 0 [HDMI ]: HDA-Intel - HDA ATI HDMI HDA ATI HDMI at 0xfdcfc000 irq 45 1 [TraktorAudio2 ]: snd-usb-caiaq - Traktor Audio 2 Native Instruments Traktor Audio 2 (usb-0000:00:1d.7-8)

  Read the article

• Broadcom 4365 wireless driver with 3.4 / 3.5 kernel

  - by zaid

  I used this package to install the driver on 3.2 Kernel and it was working perfectly. Unfortunately the system used to freeze randomly with 3.2 kernel so I installed 3.4 kernel, now there is no freezing, the only problem is that my wifi card is not working, I tried to re-install the package, but didn't work. I can see the driver in the "additional drivers" and it say that it is active, but when I execute iwconfig it doesn't show up. I've even tried ndiswraper and that didn't work either. my lspci: 01:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01)

  Read the article

• How do I install the Intel Graphics driver in my system?

  - by John

  Can someone help me out and explain or point me in the right direction on how to check video drivers and see if my video card running okay? I had 10.04 installed on my Thinkpad r61 with Compiz Manager and life was great, until the machine took water damage. I bought an ASUS (X54H) since and am trying out 12.04, but the desktop just doesn't look right. I always struggled with video driver installation. There are no proprietary drivers available in the hardware manager. When I run lspci | grep VGA: 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) I will greatly appreciate your help. I want to use Linux more, but like I said video drivers appear to be my biggest concern. I have also tried 12.04 on my desktop PC, but again failed to configure video card, so switched back to Windows 7.

  Read the article

• Public JCP EC Meeting on 12 November

  - by Heather VanCura

  The next JCP EC Meeting, and the last public EC Meeting of 2013, is scheduled for Tuesday, 12 November at 08:00 AM PST.  Agenda includes a discussion on invigorating your community participation in the JCP program. We hope you will join us, but if you cannot attend, the recording and materials will also be public on the JCP.org multimedia page. Meeting details below. Meeting information ------------------------------------------------------- Topic: Public EC Meeting Date: Tuesday, November 12, 2013 Time: 8:00 am, Pacific Standard Time (San Francisco, GMT-08:00) Meeting Number: 809 853 126 Meeting Password: 1234 ------------------------------------------------------- To start or join the online meeting ------------------------------------------------------- Go to https://jcp.webex.com/jcp/j.php?ED=239354237&UID=491098062&PW=NZjAyM2Q2YTVj&RT=MiM0 ------------------------------------------------------- Audio conference information ------------------------------------------------------- +1 (866) 682-4770 (US)   Conference code: 5731908   Security code: 1234 For global access numbers https://www.intercallonline.com/listNumbersByCode.action?confCode=5731908 Or +1 (408) 774-4073   

  Read the article

• Wireless speed drops over time and doesn't get up if not reconnected

  - by Vili Lehto

  I am using Ubuntu 12.10 64bit and I have a Asus PCE-N15 wireless card(in PCI-E slot). The problem is that first when I connect to my WiFi network the speed is just fine, and actually my link speed never drops, it shows a solid 150mb/s+ link speed and good signal. But the download and upload speeds drop dramatically after couple minutes of use and I have to reconnect to fix this. Network is type IEEE 802.11bgn and uses WPA2/AES encryption. I don't have similar problems on the windows side, and the network is working fine on every other device. iwconfig shows this: wlan0 IEEE 802.11bgn ESSID:"WLAN-AP" Mode:Managed Frequency:2.412 GHz Access Point: 00:1E:AB:05:EF:31 Bit Rate=300 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr=2347 B Fragment thr:off Encryption key:off Power Management:off Link Quality=61/70 Signal level=-49 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:2 Missed beacon:0 So the question is: Is there a way to fix this? Thanks in advance.

  Read the article

• How can I set my screen resolution to match my TV?

  - by Scott Severance

  I have a computer in my classroom that's connected to an LG smart TV (that's actually not so smart. I wouldn't recommend buying one.). For the touch interface, the TV wants a resolution of 1920x1080 at 60Hz. However, I can't seem to set the computer to that resolution. The display settings only offer 1024x768 and 640x480. The computer dual boots with Windows XP, where widescreen options are available in approximately the required size, but the exact resolution -- or even aspect ratio-- isn't available in XP either. I tried the following command: xrandr -s 1920x1080 -r 60 The response was: Size 1920x1080 not found in available modes Back in the old days, the solution would be to edit xorg.conf. However, since that file no longer exists, and I haven't found up-to-date info, I don't know what else to do. If it helps, this machine will never be connected to a different display, so resolution flexibility isn't important. Here's the output of lshw: *-display:0 description: VGA compatible controller product: 4 Series Chipset Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 03 width: 64 bits clock: 33MHz capabilities: vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:42 memory:fe800000-febfffff memory:d0000000-dfffffff ioport:ecd8(size=8) *-display:1 UNCLAIMED description: Display controller product: 4 Series Chipset Integrated Graphics Controller vendor: Intel Corporation physical id: 2.1 bus info: pci@0000:00:02.1 version: 03 width: 64 bits clock: 33MHz According to the system settings, my graphics driver is unknown and my "experience" is standard. This is 64-bit Ubuntu 12.04 (Precise) Note: There are a number of similar questions to this one, but they didn't include any answers that helped me. Update After posting this question, I noticed one in the sidebar that I hadn't found through search but which appeared to contain the answer. Based on that question, I created the /etc/X11/xorg.conf file below: Section "ServerLayout" Identifier "X.org Configured" Screen 0 "Screen0" 0 0 InputDevice "Mouse0" "CorePointer" InputDevice "Keyboard0" "CoreKeyboard" EndSection Section "Files" ModulePath "/usr/lib/xorg/modules" FontPath "/usr/share/fonts/X11/misc" FontPath "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" FontPath "built-ins" EndSection Section "Module" Load "glx" Load "dri2" Load "dbe" Load "dri" Load "record" Load "extmod" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "kbd" EndSection Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/input/mice" Option "ZAxisMapping" "4 5 6 7" EndSection Section "Monitor" Identifier "Monitor0" VendorName "LG" ModelName "Smart TV" EndSection Section "Device" ### Available Driver options are:- ### Values: <i>: integer, <f>: float, <bool>: "True"/"False", ### <string>: "String", <freq>: "<f> Hz/kHz/MHz", ### <percent>: "<f>%" ### [arg]: arg optional #Option "DRI" # [<bool>] #Option "ColorKey" # <i> #Option "VideoKey" # <i> #Option "FallbackDebug" # [<bool>] #Option "Tiling" # [<bool>] #Option "LinearFramebuffer" # [<bool>] #Option "Shadow" # [<bool>] #Option "SwapbuffersWait" # [<bool>] #Option "TripleBuffer" # [<bool>] #Option "XvMC" # [<bool>] #Option "XvPreferOverlay" # [<bool>] #Option "DebugFlushBatches" # [<bool>] #Option "DebugFlushCaches" # [<bool>] #Option "DebugWait" # [<bool>] #Option "HotPlug" # [<bool>] #Option "RelaxedFencing" # [<bool>] Identifier "Card0" Driver "intel" BusID "PCI:0:2:0" EndSection Section "Screen" Identifier "Screen0" Device "Card0" Monitor "Monitor0" DefaultDepth 24 #SubSection "Display" # Viewport 0 0 # Depth 1 #EndSubSection #SubSection "Display" # Viewport 0 0 # Depth 4 #EndSubSection #SubSection "Display" # Viewport 0 0 # Depth 8 #EndSubSection #SubSection "Display" # Viewport 0 0 # Depth 15 #EndSubSection #SubSection "Display" # Viewport 0 0 # Depth 16 #EndSubSection SubSection "Display" Viewport 0 0 Depth 24 Modes "1024x768" "1920x1080" EndSubSection EndSection According to /var/log/Xorg.0.log, my settings aren't being applied. In fact, I wonder if the config file is even being read. [ 1209.083] (**) intel(0): Depth 24, (--) framebuffer bpp 32 [ 1209.084] (==) intel(0): RGB weight 888 [ 1209.084] (==) intel(0): Default visual is TrueColor [ 1209.084] (II) intel(0): Integrated Graphics Chipset: Intel(R) G41 [ 1209.084] (--) intel(0): Chipset: "G41" [ 1209.084] (**) intel(0): Relaxed fencing enabled [ 1209.084] (**) intel(0): Wait on SwapBuffers? enabled [ 1209.084] (**) intel(0): Triple buffering? enabled [ 1209.084] (**) intel(0): Framebuffer tiled [ 1209.084] (**) intel(0): Pixmaps tiled [ 1209.084] (**) intel(0): 3D buffers tiled [ 1209.084] (**) intel(0): SwapBuffers wait enabled [ 1209.084] (==) intel(0): video overlay key set to 0x101fe [ 1209.172] (II) intel(0): Output VGA1 using monitor section Monitor0 [ 1209.260] (II) intel(0): EDID for output VGA1 [ 1209.260] (II) intel(0): Printing probed modes for output VGA1 [ 1209.260] (II) intel(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz) [ 1209.260] (II) intel(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz) [ 1209.260] (II) intel(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz) [ 1209.260] (II) intel(0): Modeline "848x480"x60.0 33.75 848 864 976 1088 480 486 494 517 +hsync +vsync (31.0 kHz) [ 1209.260] (II) intel(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 489 492 525 -hsync -vsync (31.5 kHz) [ 1209.260] (II) intel(0): Output VGA1 connected [ 1209.260] (II) intel(0): Using user preference for initial modes [ 1209.260] (II) intel(0): Output VGA1 using initial mode 1024x768 [ 1209.260] (II) intel(0): Using default gamma of (1.0, 1.0, 1.0) unless otherwise stated. [ 1209.260] (II) intel(0): Kernel page flipping support detected, enabling [ 1209.260] (==) intel(0): DPI set to (96, 96)

  Read the article

• Ubuntu 12.04, can't find my home wifi network

  - by Anton

  I've tried several solutions I found on the web, but didn't manage to solve a problem. Since today my laptop won't find my WiFi network, but neighbours' networks are suggested. Another laptop with U12.04 does find one. What do I do? I've Dell Latitude-E4310, 02:00.0 Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01) Subsystem: Dell Inspiron M5010 / XPS 8300 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f2c00000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: bcma, brcmsmac also NetworkManager Tool State: connected (global) - Device: eth1 ----------------------------------------------------------------- Type: 802.11 WiFi Driver: wl State: disconnected Default: no HW Address: 1C:65:9D:7A:45:5C Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Should I provide anything else? Many thanks in advance.

  Read the article

• Dell wireless not working after upgrade

  - by Omer Saeed

  So, the short version of my sad story is that I tried upgrade Ubuntu to 12.04 and wireless driver has stopped working. I have tried all the solutions but nothing seem to be working. When I try to install my wireless from "Additional Drivers" Its says: Sorry, installation of this driver failed. Please have a look at the log file for details: /var/log/jockey.log The lspci command gives me the following info about wireless: 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) I have tried removing bcm drivers and reinstalling, but nothing seems to be working. rfkill is good too.

  Read the article

• Loud and annoying noise on login

  - by searchfgold6789

  I have a PC with Kubuntu 13.10 64-bit on it. The problem is that whenever I log in (automatic log in is enabled), there is a loud double-click noise that sounds from the speakers whether the volume is muted or not. I have two sound cards; the motherboard audio, which is disabled in the BIOS, and the Creative! Labs Sound Blaster X-Fi SB0460, which I have normal speakers plugged into. Does anyone know how to fix this? Relative lspci lines: 00:01.1 Audio device: Advanced Micro Devices, Inc. [AMD/ATI] BeaverCreek HDMI Audio [Radeon HD 6500D and 6400G-6600G series] 02:05.0 Multimedia audio controller: Creative Labs SB X-Fi Using default Phonon backend. (I am not really sure what other information to provide, but will gladly edit in anything upon request.)

  Read the article

• No boot record when installing 13.04 from USB on WinXP

  - by Phil Leslie

  I'm replacing WinXP with 13.04 on an older PC using wubi.exe on a USB stick. I had no problem changing the BIOS on another system that was a bit newer but when I change the settings on the older PC to boot from USB, I get a DOS message saying "Searching for boot record...Not found" & asked to try again. I don't have the ability to boot from a live CD so is there a reason why I can boot from a USB on a newer computer but can't from an older one? Both have options to choose to boot from USB, but the older one can find no boot record. The system was built on 12/13/01 by American Megatrends. Since I don't have enough "reputation points" to post the screen shot image, you can see it at http://img.photobucket.com/albums/v633/boonevillephil/1029131748-00.jpg.

  Read the article

• How do I rotate my monitor using xorg?

  - by user1106405

  I have just installed KUbuntu 12.10, and I am attempting to rotate my monitor 90 deg to the left. When I add the option to rotate, the monitor seems to ignore the directive. I'm currently using dual 02:00.0 VGA compatible controller: NVIDIA Corporation GF104 [GeForce GTX 460] (rev a1) 03:00.0 VGA compatible controller: NVIDIA Corporation GF104 [GeForce GTX 460] (rev a1) and NVidia driver version 310 My xorg.conf is as follows: # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 304.51 (buildd@komainu) Fri Oct 12 12:53:49 UTC 2012 # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 310.14 ([email protected]) Tue Oct 9 13:04:01 PDT 2012 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 1280 0 Screen 1 "Screen1" RightOf "Screen0" Screen 2 "Screen2" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "1" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Samsung SyncMaster" HorizSync 30.0 - 81.0 VertRefresh 56.0 - 60.0 Option "DPMS" EndSection Section "Monitor" Identifier "Monitor1" VendorName "Unknown" ModelName "DELL 1908WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 EndSection Section "Monitor" Identifier "Monitor2" VendorName "Unknown" ModelName "DELL 1907FP" HorizSync 30.0 - 81.0 VertRefresh 56.0 - 76.0 EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GTX 460" BusID "PCI:2:0:0" Screen 0 EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GTX 460" BusID "PCI:2:0:0" Screen 1 EndSection Section "Device" Identifier "Device2" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GTX 460" BusID "PCI:3:0:0" EndSection Section "Screen" # Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+0; DFP-0: nvidia-auto-select +0+0; DFP-0: 1920x1200 +0+0; DFP-0: 1920x1200_60 +0+0; DFP-0: 1600x1200 +0+0; DFP-0: 1600x1200_60 +0+0; DFP-0: 1280x1024 +0+0; DFP-0: 1280x1024_60 +0+0; DFP-0: 1280x960 +0+0; DFP-0: 1280x960_60 +0+0; DFP-0: 1024x768 +0+0; DFP-0: 1024x768_60 +0+0; DFP-0: 800x600 +0+0; DFP-0: 800x600_60 +0+0; DFP-0: 800x600_56 +0+0; DFP-0: 640x480 +0+0; DFP-0: 640x480_60 +0+0; DFP-0: nvidia-auto-select @1920x1080 +0+0; DFP-0: nvidia-auto-select @1920x720 +0+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "Stereo" "0" Option "metamodes" "DFP-0: nvidia-auto-select +0+0; DFP-0: nvidia-auto-select +0+0; DFP-0: 1920x1200 +0+0; DFP-0: 1920x1200_60 +0+0; DFP-0: 1600x1200 +0+0; DFP-0: 1600x1200_60 +0+0; DFP-0: 1280x1024 +0+0; DFP-0: 1280x1024_60 +0+0; DFP-0: 1280x960 +0+0; DFP-0: 1280x960_60 +0+0; DFP-0: 1024x768 +0+0; DFP-0: 1024x768_60 +0+0; DFP-0: 800x600 +0+0; DFP-0: 800x600_60 +0+0; DFP-0: 800x600_56 +0+0; DFP-0: 640x480 +0+0; DFP-0: 640x480_60 +0+0; DFP-0: nvidia-auto-select +0+0; DFP-0: nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "Stereo" "0" Option "metamodes" "DFP-2: nvidia-auto-select +0+0" Option "Rotate" "left" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen2" Device "Device2" Monitor "Monitor2" DefaultDepth 24 Option "Stereo" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Extensions" Option "Composite" "Enable" EndSection Edit: If I delete the xorg.conf and reboot, I am able to rotate my monitor, however, my third monitor is not recognized: Screen 0: minimum 8 x 8, current 3360 x 1200, maximum 16384 x 16384 DVI-I-0 disconnected (normal left inverted right x axis y axis) DVI-I-1 disconnected (normal left inverted right x axis y axis) DVI-I-2 connected 1920x1200+0+0 (normal left inverted right x axis y axis) 518mm x 324mm 1920x1200 60.0*+ 1600x1200 60.0 1280x1024 60.0 1280x960 60.0 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 HDMI-0 disconnected (normal left inverted right x axis y axis) DVI-I-3 connected 1440x900+1920+0 (normal left inverted right x axis y axis) 408mm x 255mm 1440x900 59.9*+ 75.0 1280x1024 75.0 60.0 1280x800 59.8 1152x864 75.0 1024x768 75.0 70.1 60.0 800x600 75.0 72.2 60.3 56.2 640x480 75.0 72.8 59.9

  Read the article

• Why does sound stop working after a while?

  - by badp

  I don't know how to reproduce this problem, because I don't regularly play music or sound. All I know is that, sometimes, I'll load a video (from youtube or from a local file) and there will be no sound. Everything looks fine software wise: Rebooting always fixes. aplay, paplay and pals give no error message I'm not in the audio group, as advised The device exists and appears in use: $ lsof /dev/snd/by-path/pci-0000\:00\:1b.0 COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME pulseaudi 17313 badp 23u CHR 116,10 0t0 7628 /dev/snd/by-path/../controlC0 pulseaudi 17313 badp 30u CHR 116,10 0t0 7628 /dev/snd/by-path/../controlC0 Restarting pulseaudio or alsa seems to do no good. What is wrong here?

  Read the article

< Previous Page | 96 97 98 99 100 101 102 103 104 105 106 107  | Next Page >