Search Results

Search found 5318 results on 213 pages for 'managed'.

Page 101/213 | < Previous Page | 97 98 99 100 101 102 103 104 105 106 107 108  | Next Page >

• Internet Timeouts with TP-Link TL-WN821N v2 wireless usb stick

  - by user1622959

  A short time after accessing the internet, the browser/download times out. Before the timeout, the internet works OK briefly; afterwards, the wireless is still connected with a strong signal, but every internet access results in a timeout. When I leave the PC for a while, the internet is back just to timeout again as soon as I start using it. The same happens when I reconnect to the router. Also, when I surf the internet, it takes a couple of minutes until the timeout, but when I download something, it times out in a matter of seconds. The wireless adapter works just fine in Windows and internet via ethernet cable works just fine in Ubuntu. Does anyone have the same problem or knows a solution. I use Ubuntu 12.10 x64. The problem occurs since I installed ubuntu (which was a few days ago). Here some stuff that might be usefull: serus@serus-Ubuntu-PC:~$ lsusb Bus 002 Device 002: ID 0cf3:1002 Atheros Communications, Inc. TP-Link TL-WN821N v2 802.11n [Atheros AR9170] serus@serus-Ubuntu-PC:~$ lsmod Module Size Used by carl9170 82083 0 serus@serus-Ubuntu-PC:~$ modinfo carl9170 filename: /lib/modules/3.5.0-21- generic/kernel/drivers/net/wireless/ath/carl9170/carl9170.ko alias: arusb_lnx alias: ar9170usb firmware: carl9170-1.fw description: Atheros AR9170 802.11n USB wireless serus@serus-Ubuntu-PC:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"virginmedia0137463" Mode:Managed Frequency:2.462 GHz Access Point: A0:21:B7:F8:29:B6 Bit Rate=240 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=66/70 Signal level=-44 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:1399 Invalid misc:18 Missed beacon:0 serus@serus-Ubuntu-PC:~$ sudo lshw -C network *-network description: Wireless interface physical id: 1 bus info: usb@2:2 logical name: wlan0 serial: 00:27:19:bb:00:19 capabilities: ethernet physical wireless configuration: broadcast=yes driver=carl9170 driverversion=3.5.0-21-generic firmware=1.9.4 ip=192.168.0.6 link=yes multicast=yes wireless=IEEE 802.11bgn

  Read the article

• How do I get a Belkin F5D8053 wireless adapter working?

  - by disassembler

  I've tried getting my Belkin N Wireless adapter to work on Ubuntu many times with no luck at all. Each time I seem to arrive at a dead end. After some thorough searching of UbuntuForums and WifiDocs I've gathered some information and narrowed the problem down to an issue with the rtl819xU driver. Here's some info that may help: $ sudo lshw -C network *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:2 logical name: wlan0 serial: 00:22:75:38:52:ac capabilities: ethernet physical wireless configuration: broadcast=yes driver=rtl819xU multicast=yes wireless=802.11b/g/n $ sudo lsmod Module Size Used by vesafb 13449 1 snd_ice1724 106559 2 snd_ice17xx_ak4xxx 13163 1 snd_ice1724 snd_ac97_codec 105614 1 snd_ice1724 ac97_bus 12642 1 snd_ac97_codec snd_ak4xxx_adda 18436 2 snd_ice1724,snd_ice17xx_ak4xxx snd_ak4114 14326 1 snd_ice1724 snd_pt2258 12986 1 snd_ice1724 snd_i2c 13831 2 snd_ice1724,snd_pt2258 snd_ak4113 14307 1 snd_ice1724 snd_pcm 80244 4 snd_ice1724,snd_ac97_codec,snd_ak4114,snd_ak4113 fglrx 2434640 121 snd_seq_midi 13132 0 snd_rawmidi 25269 2 snd_ice1724,snd_seq_midi binfmt_misc 13213 1 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51291 2 snd_seq_midi,snd_seq_midi_event ppdev 12849 0 snd_timer 28659 2 snd_pcm,snd_seq snd_seq_device 14110 3 snd_seq_midi,snd_rawmidi,snd_seq dcdbas 14054 0 r8192u_usb 297246 0 snd 55295 16 snd_ice1724,snd_ac97_codec,snd_ak4xxx_adda,snd_ak4114,snd_pt2258,snd_i2c,snd_ak4113,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 12600 1 snd parport_pc 32111 1 snd_page_alloc 14073 1 snd_pcm shpchp 32345 0 lp 13349 0 parport 36746 3 ppdev,parport_pc,lp usbhid 41704 0 hid 77084 1 usbhid e100 40108 0 floppy 60032 0 $ sudo iwconfig wlan0 802.11b/g/n Mode:Managed Access Point: Not-Associated Bit Rate:1 Mb/s Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=0/100 Signal level=0 dBm Noise level=0 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I'd like to know if 1) Is the driver is properly installed and recognized by Ubuntu? 2) What can I do to load the drivers properly and make use of the adapter? Thanks!

  Read the article

• Dealing with inflexible programmers.

  - by Singleton

  Sometimes programmers who work on a project for long time get inflexible, and it becomes difficult to reason with them. Even if we do manage to convince them, they can be unlikely to implement our suggestions. For instance, I recently joined a project where the build & release process is too complicated and has unnecessary roadblocks. I suggested that we get rid of some of the development overhead (like filling a few spreadsheets) just by integrating defect management and version control tools (both are IBM-Rational tools so integration can be a very easy one-off effort). Also, if we use tools like Maven & Ant (the project involves Java and some COTS products) build & release can be simplified which should reduce manual errors & intervention. I managed to convince others and I'm ready to put in the effort to develop a proof of concept. But the ‘Senior’ developer is not willing, possibly because the current process makes him more valuable. How do we handle this situation without developing friction in the team?

  Read the article

• Oracle SOA Suite on Virtual Box

  - by sravan.sarraju(at)oracle.com

  Recently I have started my journey Oracle SOA Suite and the first big hurdle everyone warned me off is setting up Oracle SOA Suite environment in our personal machine for learning. My laziness pushed me to search for much easier way than regular all download, configuration stuff and bang..! I found in the solution oracle site itself. Oracle SOA Suite on Virtual Box. For those who are not aware of Virtual Box, it’s a virtualization software which enables u to install multiple operating systems on a virtual hard drive which in turn managed by Virtual Box. In short pack ur Operating System, Software, Files everything into a VM and carry it wherever u go. Coming to Oracle SOA Suite, Oracle is offering a prebuilt VM for download which u can mount on ur Virtual box and that all you need. Here is the link for Virtual Box image of Oracle SOA Suite. Virtual Box can be downloaded here It’s a huge download. I’m yet to try it myself. Will get back to my writer again once I’m done.

  Read the article

• Using Ogre with android [closed]

  - by Rich

  I am trying get Ogre 3d to work on android, I have managed to download and run the ogre sample browser but I am really struggling with trying to get a basic application working i have been trying for days now with no avail. Does anyone have any pointers on where to start with this? Thanks if anyone can help EDIT: Very sorry for my rubbish question! I am a bit new to this and I am just trying to seek some guidance. Ok so i followed the instructions on the Ogre wiki to build ogre for android and the sample browser here: http://www.ogre3d.org/tikiwiki/tiki-index.php?page=CMake+Quick+Start+Guide&tikiversion=Android so it is deffinately possible. The issue I am having is knowing what I need to do to get started with ogre e.g just a simple hello world style app where it might just show the ogre head, so tutorials might actually be good because I could not really find any simple ones as I am very new to 3D development. I just found that the sample browser was just massive and yes it has everything in it but it's very difficult to understand how it all works. What I am asking is basically some help, as I have been trying to pull out some parts of the sample browser to just create a view with a 3D model. Hope this is better?

  Read the article

• Should I build a multi-threaded system that handles events from a game and sorts them, independently, into different threads based on priority?

  - by JonathonG

  Can I build a multi-threaded system that handles events from a game and sorts them, independently, into different threads based on priority, and is it a good idea? Here's more info: I am about to begin work on porting a mid-sized game from Flash/AS3 to Java so that I can continue development with multi-threading capabilities. Here's a small bit of background about the game: The game contains numerous asynchronous activities, such as "world updating" (the game environment is constantly changing based on a set of natural laws and forces), procedural generation of terrain, NPCs, quests, items, etc., and on top of that, the effects of all of the player's interactions with his environment are programmatically calculated in real time, based on a set of constantly changing "stats" and once again, natural laws and forces. All of these things going on at once, in an asynchronous manner, seem to lend themselves to multi-threading very well. My question is: Can I build some kind of central engine that handles the "stacking" of all of these events as they are triggered, and dynamically sorts them out amongst the available threads, and would it be a good idea? As an example: Essentially, every time something happens (IE, a magic missile being generated by a spell, or a bunch of plants need to grow to their next stage), instead of just processing that task right then and adding the new object(s) to a list of managed objects, send a reference to that event to a core "event handler" that throws it into a stack of all other currently queued events, which then sorts them out and orders them according to urgency, splits them between a number of available threads for as-fast-as-possible multithreaded execution.

  Read the article

• wireless blocked after installing ubuntu 12.04

  - by Cornelia Frank

  I am using a lenovo S10-3 ideapad; had no problems with earlier version of ubuntu, only since installing 12.04. Have looked through many of the questions on the same issue and tried potential solutions but cannot seem to solve my problem. The hardware switch is in 'on' position and the wireless light comes on very briefly (2-3 sec) when the laptop starts up but then goes off and stays off. Pressing FN+F5 does nothing at all. I'd be grateful for any assistance. Cornelia Have received the following responses in Terminal: cf@cf-Lenovo:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes cf@cf-Lenovo:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. cf@cf-Lenovo:~$ lshw -C network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: 00:26:9e:ee:7f:4c size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=10.0.1.8 latency=0 multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0520000-f0520fff memory:f0510000-f051ffff memory:f0540000-f055ffff *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 01 serial: c4:17:fe:f8:bc:d7 width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f010ffff WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

  Read the article

• A fix for the design time error in MVVM Light V4.1

  - by Laurent Bugnion

  For those of you who installed V4.1 of MVVM Light and created a project for Windows Phone 8, you will have noticed an error showing up in the design surface (either in Visual Studio designer, or in Expression Blend). The error says: “Could not load type ‘System.ComponentModel.INotifyPropertyChanging’ from assembly ‘mscorlib.extensions’” with additional information about version numbers. The error is caused by an incompatibility between versions of System.Windows.Interactivity. Because this assembly is strongly named, any version incompatibility is causing the kind of error shown here (for an interesting discussion on the strong naming issue, see this thread on Codeplex). I managed to resolve the issue for Windows Phone 8 and will publish a cleaned up installer next week. In the mean time, in order to allow you to continue development, please follow the steps: Download the new DLLs zip package (MVVMLight_V4_1_25_WP8). Right click on the Zip file and select Properties from the context menu. Press the “Unblock” button (if available) and then OK. Right click again on the zip package and select “Extract all…”. Select a known location for the new DLLs. Open the MVVM Light project with the design time error in Visual Studio 2012. Open the References folder in the Solution Explorer. Select the following DLLs: GalaSoft.MvvmLight.dll, GalaSoft.MvvmLight.Extras.dll, Microsoft.Practices.ServiceLocation.dll and System.Windows.Interactivity.dll. Press “delete” and confirm to remove the DLLs from your project. Right click on References and select Add Reference from the context menu. Browse to the folder with the new DLLs. Select the four new DLLs and press OK. Rebuild your application, and open it again in Blend or in the Visual Studio designer. The error should be gone now. In the next few days, as time allows, I will publish a new MSI containing a fixed version of the DLLs as well as a few other improvements. This quick fix should however allow you to continue working on your Windows Phone 8 projects in design mode too.   Laurent Bugnion (GalaSoft) Subscribe | Twitter | Facebook | Flickr | LinkedIn

  Read the article

• Can't install Linux drivers for ASUS N-13 wireless adapter

  - by jcc

  I have a USB N13 wireless Adapter with install CD-- For Windows. I downloaded drivers from ASUS FOR N13 for Linux. Disregard install CD that came with adapter; it's for Windows. I then downloaded Windows Wireless driver install program app from Software Center in Ubuntu 12.10. The problem is me. I am newbie with all things linux; software sources, G Debi, default archive manager, synaptic package manager and the Terminal. The downloaded driver file is a .zip file. I managed to extract it to a tar.gz file and then to open it to the contained files. When I use the Windows Wireless driver program it ends up telling me there is no .inf file and goes no further. It wants to install .inf file but I don't even see one in all the files. Can someone please help me . I think you can tell by my wording I don't have a clue. I hope this is'nt too chatty. I've tried to be explicit and to the point. Thank you. Oh, this is on an ASUS LAPTOP K53E. I've looked all over Ask Ubuntu and finally found some questions even on the N13 but they didn't help; still some differences in the exact problem.

  Read the article

• System in low graphics, deleted linux, grub rescue, can't access windows

  - by First timer

  So I'm pretty new to Ubuntu but I managed to install it with no big problems on both my desktop and netbook. When I installed it on my brother's netbook everything went horribly wrong and now I fear the system is close to beyond repair. The problem was first that it said it did not have any space left (seemed ridiculous since it had a lot). Then Ubuntu began booting into a "System is running in low graphics mode error" which I then tried to fix, using all the tips I could find in here but nothing helped. I think the graphics error and lack of space might have been related but I can't be sure. Finally I gave up repairing Ubuntu and went for a reinstall. Shouldn't have done that! I read that I should simply open Ubuntu through a live usb and choose GParted to delete the Linux partitions so I did and rebooted accordingly. Next, I was to install Ubuntu but now I am only given the option to wipe the whole disk for Ubuntu, not install along with windows 7. If I access GParted I can still see the ntfs partitions that hold windows 7 (there are 2: one labeled RECOVERY and another labeled OS and boot) so why can't I access them? Btw. the OS and boot has a little red mark with a warning that 1 cluster is referenced to multiple times, don't know what that means. If I boot without the live usb I am sent directly into a grub rescue "black screen of the computer will follow no orders". Please, I know that the easiest might be to simply wipe the whole thing clean but there are important files and programs on windows 7. Is there a way to just access windows? It is a dell inspiron 1018 mini netbook, so I have no cd input and no windows 7 installation cd.

  Read the article

• What's the canonical process for backing up a website?

  - by Walkerneo

  This is going to sound terrible, but bear with me. I currently have a cron job that does a mysql dump, a git add all and commit, and a git push to bitbucket. I set this up almost a year ago, when I didn't know much about git, backups, and general web development and administration. I haven't had the time to fix this and do it properly, but the repo has now grown quite big from accumulating large temporary files from my forum, so now I have to do something and I want to do it properly this time around. What processes do semi-large websites and personal site admins use for backing up server content? Based on what I've learned since I set this up, what I'm currently think of doing is: Making changes on a development domain and committing the code frequently Archiving the entire site after a successful deployment from the development domain Having automatic daily database and user-content backups. I still like the idea of backing up sqldumps with git, though. I know git isn't a backup tool and that this is beyond its purpose, but the textual queries that are exported would be easily managed by git and would save a lot of space in archives.

  Read the article

• Share home directory between Linux and Windows dual boot

  - by user877329

  This question is somewhat similar to How to use Windows Share has home directory, but in this case Windows is not running. I have installed a dual-boot configuration with Ubuntu 12.04 and Windows. My Windows partition is mounted on /C. Now I want either Ubuntu to locate home directories in /C/Users Which is the location of windows accounts or I want Windows to use D:\home for home directories. (D is the name of the Ubuntu root directory). For the first approach, I have managed to create a test user account test-user:x:1004:1001:Test:/C/Users/test-user:/bin/bash The account works but test-user cannot run any X session. From .xsession-errors chmod: Changing rights on ”/C/Users/test-user/.xsession-errors”: Operation not permitted Would it help get rid of that chmod, which has no effect? How do I? If I use the second approach, I need the Ext2fsd driver, which seems to work, but I am not sure if Windows maps the Ext2 system that early. Here is my fstab proc /proc proc nodev,noexec,nosuid 0 0 UUID=e7cef061-ed8d-4a82-b708-0c8f4c6f297f / ext3 errors=remount-ro 0 1 UUID=2CDCEB43DCEB0644 /C ntfs defaults,umask=007,gid=46 0 0 UUID=b087b5c0-b4bd-47e7-8d34-48ad9b192328 none swap sw 0 0 Update: I found something here: http://www.tuxera.com/community/ntfs-3g-advanced/ Will work if i do a correct mapping between NT users and Linux users.

  Read the article

• Gems In The Visual Studio 2010 Training Kit &ndash; Introduction to MEF: Learning Labs

  - by Jim Duffy

  No, this post doesn’t have anything to do with cooking up illegal drugs in some rundown shack outside of town. That, my friends, would be a meth lab and fortunately that is waaaaay outside my area of expertise. Now I can talk Kentucky bourbon, or as Homer Simpson would say “mmmmmmmmmmm bourbon”, with you but please refrain from asking me meth questions. :-) Anyway, what I’m talking about are the MEF (Managed Extensibility Framework) Learning Labs contained in the Visual Studio 2010 and .NET Framework 4 Training Kit. Not sure what MEF is and need an overview? Then start here or here. Ok, so you’ve read a bit about MEF or heard about MEF and you’re thinking it might be something you and your development team might want to take a hands-on look at. I have good news then because contained in the Visual Studio 2010 and .NET Framework 4 Training Kit is a series of hands-on learning labs for MEF. I’ve added working my way through them to my “things I want to take a closer look at” list. Have a day. :-|

  Read the article

• Why can't I install 10.04 on a system that already has 8.04?

  - by Android Eve

  Ubuntu 10.04 is beautiful. I love it. I am dying to install it on my PC, alongside the existing Ubuntu 8.04 (from which I write this message right now). But... it won't let me! When I reach the partitioning stage (manual!) Ubuntu 10.04 sees my two HDDs as one RAID volume. It doesn't see all the partitions I already have in place in /dev/sda and /dev/sdb. Even Windows 7 doesn't behave like this... (yes, I actually managed to install Windows 7 64-bit in dual-boot configuration with Ubuntu 8.04 on this same system). Note: GParted on Ubuntu 10.04 (live CD) sees the partition intended for Ubuntu 10.04 (/dev/sda4) perfectly, but is unable to format it. Note: I also removed that partition trying to reformat it via GParted once 10.04 LiveCD is loaded. It didn't help. I believe that the problem lies in Ubuntu "deciding for me" that the HDDs should be "seen" as a RAID, hence any partition is seen by GParted as "busy" or "locked". Any idea how to solve this problem?

  Read the article

• What kind of physics to choose for our arcade 3D MMO?

  - by Nick

  We're creating an action MMO using Three.js (WebGL) with an arcadish feel, and implementing physics for it has been a pain in the butt. Our game has a terrain where the character will walk on, and in the future 3D objects (a house, a tree, etc) that will have collisions. In terms of complexity, the physics engine should be like World of Warcraft. We don't need friction, bouncing behaviour or anything more complex like joints, etc. Just gravity. I have managed to implement terrain physics so far by casting a ray downwards, but it does not take into account possible 3D objects. Note that these 3D objects need to have convex collisions, so our artists create a 3D house and the player can walk inside but can't walk through the walls. How do I implement proper collision detection with 3D objects like in World of Warcraft? Do I need an advanced physics engine? I read about Physijs which looks cool, but I fear that it may be overkill to implement that for our game. Also, how does WoW do it? Do they have a separate raycasting system for the terrain? Or do they treat the terrain like any other convex mesh? A screenshot of our game so far:

  Read the article

• My internet connection slows or dies unexpectedly

  - by genesis

  I installed Ubuntu 10.04 once again and I'm having some problems which I had before, but I have no idea how I solved them. On Windows, everything's working fine and I had no problems with this. My problem is that sometimes, when browsing through the internet, webpages just start to load really slow, sometimes it doesn't load anything at all (Error 118 (net::ERR_CONNECTION_TIMED_OUT): The operation timed out.) and it starts to work after few minutes. My IPv4 settings are automatic (DHCP), and IPv6 settings are Ignored/Disabled. I think my previous problems had something to do with IPv6, but I'm not sure. Is there a fix for this? iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"Fsite1" Mode:Managed Frequency:2.442 GHz Access Point: C8:3A:35:40:43:68 Bit Rate=0 kb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality=43/70 Signal level=-67 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0

  Read the article

• Setting up group disk quotas

  - by Ray

  I am hoping to get some advice in setting up disk quotas. So, I know about: Adding usrquota and grpquota on to /etc/fstab for the file systems that need to be managed. Using edquota to assign disk quotas to users. However, I need to do the last step for multiple users and edquota seems to be a bit troublesome. One solution that I have found is that I can do: sudo edquota -u foo -p bar. This will copy the disk quota of bar to user foo. I was wondering if this is the best solution? I tried setting up group disk quotas but they don't seem to be working. Are group quotas meant to help in the assignment of the same quota to multiple users? Or are they suppose to give a total limit to a set of users? For example, if users A, B, C are in group X then assigning a quota of 20 GB gives each user 20 GB or does it give 20 GB to the entire group X to divide up? I'm interested in doing the former, but not the latter. Right now, I've assigned group disk quotas and they aren't working. So, I guess it is due to my misunderstanding of group disk quotas... My problem is I want to easily give the same quota to multiple users; any suggestions on the best way to do this out of what I've tried above or anything else I may not have thought of? Thank you!

  Read the article

• Ethernet Connection Unavailable

  - by fabikw

  I'm running Ubuntu Server 12.04 on a laptop with an Intel NIC (driver e1000e). When I connect the ethernet port to the internet (college network, DHCP) it works out of the box. Now I'm trying to connect it to a networked USRP (if you want to know what it is). A friend of mine managed to do this in his laptop (running regular Ubuntu 12.04) just by setting up a new Wired connection in the Network Manager with appropriate addresses. However, when I do the same, no wired connections are available. The output of nmcli -p dev is =========================================== Status of devices =========================================== DEVICE TYPE STATE ------------------------------------------- wlan0 802-11-wireless connected eth0 802-3-ethernet unavailable but the cable is connected to the device and the device is powered up. Any idea how to solve this? UPDATE: After stopping the network-manager service, setting up the connection manually and starting the service again, it now detects the ethernet connection. However, the device still can't receive data and doesn't answer to pings. UPDATE 2: As suggested I tried using a cross over cable but the result is exactly the same. However, I found out that connecting the device to the dock (as opposed to directly to the laptop) works fine. I know that the ethernet port in the laptop works fine, because connecting to the network through it works. Is it possible that the port in the laptop doesn't support Gb Ethernet (because that's what the device requires) but the one in the dock does?

  Read the article

• Should Developers Perform All Tasks or Should They Specialize?

  - by Bob Horn

  Disclaimer: The intent of this question isn't to discern what is better for the individual developer, but for the system as a whole. I've worked in environments where small teams managed certain areas. For example, there would be a small team for every one of these functions: UI Framework code Business/application logic Database I've also worked on teams where the developers were responsible for all of these areas and more (QA, analsyt, etc...). My current environment promotes agile development (specifically scrum) and everyone has their hands in every area mentioned above. While there are pros and cons to each approach, I'd be curious to know if there are more pros and cons than I list below, and also what the generally feeling is about which approach is better. Devs Do It All Pros 1. Developers may be more well-rounded 2. Developers know more of the system Cons 1. Everyone has their hands in all areas, increasing the probability of creating less-than-optimal results in that area 2. It can take longer to do something with which you are unfamiliar (jack of all trades, master of none) Devs Specialize Pros 1. Developers can create policies and procedures for their area of expertise and more easily enforce them 2. Developers have more of a chance to become deeply knowledgeable about their specific area and make it the best it can be 3. Other developers don't cross boundaries and degrade another area Cons 1. As one colleague put it: "Why would you want to pigeon-hole yourself like that?" (Meaning some developers won't get a chance to work in certain areas.) It's easy to say how wonderful agile is, and that we should do it all, but I'm somewhat of a fan of having areas of expertise. Without that expertise, I've seen code degrade, database schemas become difficult to manage, hack UI code, etc... Let's face it, some people make careers out of doing just UI work, or just database work. It's not that easy to just fill in and do as good of a job as an expert in that area.

  Read the article

• Lenovo v570 ubuntu 12.04 wireless hard blocked even when ext. switch is on

  - by user100987

  When I run iwconfig it say's lo and eth0 have no wireless extensions, but wlan0 it says IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS the:off Fragment the:off Power Management:off and I believe that's my problem, I just don't know how to turn it back on Any help? When I ran lspci | grep Network it gave me this 02:00.0 Network controller: Intell Corporation Centrino Wireless -N + WiMAX 6150 (rev 67) How I know that my wireless is hard blocked because when I run sudo rfkill list all I get 0: Ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes when I run lshw -c network I get. *-network DISABLED description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: mon1 version: 67 serial: 40:25:c2:d2:96:2c width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list logical wireless ethernet physical configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-32-generic-pae firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:d0500000-d0501fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: f0:de:f1:d7:a0:4d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.0.65 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:d0404000-d0404fff memory:d0400000-d0403fff

  Read the article

• A few tips on deploying Secure Enterprise Search with PeopleSoft

  - by Matthew Haavisto

  Oracle's Secure Enterprise Search is part of PeopleSoft now.  It is provided as part of the Peopltools platform as an appliance, and is used with applications starting with release 9.2.  Secure Enterprise Search is a rich and powerful search product that can enhance search and navigation in PeopleSoft applications.  It also provides useful features like facets and filtering that are common in consumer search engines.Several questions have arisen about the deployment of SES and how to administer it and insure optimum performance.  People have also asked about what versions are supported on various platforms.  To address the most common of these questions, we are posting this list of tips.Platform SupportSES 11.1.2.2 does not support some of the platforms supported by PeopleTools, such as Windows 2012 and AIX 7.1. However, PeopleSoft and SES can use different operating system platforms when SES is deployed on a separate machine.SES 11.2.2.2 will have the required platform support for PT 8.53 in the future. We are planning to certify PT 8.53 once the testing is complete in 8.54 development and all platform support is released for 11.2.2.2.ArchitectureWe recommend running SES on a separate machine (from your apps) for two reasons:1.    SES bundles specific WebLogic, Java, and Oracle DB versions and might need different OS patches at a minimum than PeopleSoft. By having SES run on a different machine, these pre-requisites can be managed better through their lifecycle independenly for PeopleSoft and SES.2.    SES is resource intensive - it runs it's own WebLogic and Oracle database. By having SES run on its own machine, sufficient resources can be allocated to SES and free the PeopleSoft servers from impacts of SES load patterns.We will be providing a comprehensive red paper covering PeopleSoft/SES administration in the near future, but until that is published, we'll post tips on this blog.

  Read the article

• Windows 8.1 - unfixable grub

  - by Nick

  I have a Gigabyte laptop that came with secure boot and windows 8. After a bit of battling, I managed to get my dual boot with Ubuntu 13.10.. Anyway, I upgraded zindows to 8.1, now grub is gone. I restarted from a live CD and chrooted to my drive. I used boot-repair multiple times (with successful output) both in default and with some advanced options; also reinstalled grub manually... Each time it tries once to boot to grub but gives a message for a very short amount of time. I recorded it and it is a regular bios message "Rebbot and Select proper Boot device of Insert Boot media in selected boot device and press a key" I even tried something called EasyBCD under winblows, it shows the correct boot options, but same there, it is unable to make the linux partition fire up. Anyway, no way to boot my linux box. Does anyone have an idea how to fix this? No need to redirect me to another post with grub reinstall or boot-repair, seen them all... I am thinking of trying this other boot loader, refind, to see if it works http://www.rodsbooks.com/refind/index.html Also re-reading this bios message, I'm thinking my partition might not have a boot flag anymore... I'll try that too with parted. Although both grub and win 8 are supposed to fire up from the same boot partition (the EFI one) Please help! thx

  Read the article

• How can one-handed work in Ubuntu be eased?

  - by N.N.

  My right hand is temporarily immobilized and I would like to do some minor general work on my computer. Mostly web browsing, mailing and file and directory browsing and editing. For this I currently use Firefox, Thunderbird, Nautilus and the GNOME terminal (I have already asked a specific question about Emacs). Are there ways to ease such, or any other general, one-handed work in Ubuntu? I have found http://stackoverflow.com/questions/2391805/how-can-i-remain-productive-with-one-hand-completely-immobilized but that is not exactly what I am asking for. I want to ease whatever little time spent one-handed in Ubuntu and this is also interesting for situations where there is no injury involved, such as when one hand is occupied. I do realize I should avoid unnecessary strain. The main thing that is much slower one-handed is writing. Since I am only temporarily immobilized it seems to make no sense learn a new keyboard layout. I would be surprised if I managed to learn and become more effective with a new keyboard layout (than one-handed QWERTY) before I can use my other hand again. What I have already found: Sticky keys for making it easier to enter keyboard commands. When writing one-handed there are more cases of where it is useful to paste in phrases rather than to reenter them. It is easier to use Super+S rather than CtrlAlt+arrow keys to switch work space.

  Read the article

• Laptop Display Not Working

  - by etrask

  Hello, I just purchased this laptop. It is working fine but I want to use Xubuntu on it. I managed to get 10.04 installed and running but it did not recognize/use the wireless card. So I want to try 10.10. However, every time I try, the screen goes black and never comes back on. I have tried the Live CD and Alternate install CDs, for both Ubuntu and Xubuntu 10.10. After I select "Install Ubuntu" or "Try Ubuntu", the screen blacks out and never displays anything. So I deleted "quiet" and "splash" off the command line to see what messages would come up. A bunch of text flies by but it ends at: [time] TCP established hash table entries: 524288 (order: 11, 8388608 bytes) [time] TCP bind hash table entries 65536 (order: 8, 1048576 bytes) [time] TCP: Hash tables configured (established 524288 bind 65536) [time] TCP reno registered [time] UDP hash table entries: 2048 (order: 4, 65536 bytes) [time] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) [time] NET: Registered protocol family 1 And freezes here forever. I have tried nomodeset, vga=771, and xforcevesa with no progress. Is my video card simply not going to work with this distro? It seems strange that 10.04 would work fine but not 10.10. Any help is appreciated, thank you.

  Read the article

• Install a i386 printer driver into an amd64 distribution or how can I find a good printer based on features?

  - by Yanick Rochon

  Hi, I just bought a Lexmark Interpret S408 all-in-one printer. The box said that it supported Ubuntu 8.04, but I told myself it should work with Lucid... well no. The only driver I have found is for i386 while I have a amd64 image installed; the architecture is incompatible. So, the quesiton is : Is it possible to install that driver anyway, somehow? Or do I need to take that printer back to the store and buy another one? If the latter is the only alternative, I need a printer that has wireless connection capability can do color printing is of good price (less than $200 CAD) Thank you for your answers, help, and tips. ** UPDATE ** The driver was given in the form of deb package (for Debian distributions) and I managed to extract the actual deb package driver out of the install program. I ran sudo dpkg -i --force-all lexmark-inkjet-09-driver-1.5-1.i386.deb and the driver installed, and I was able to print something out. But that pretty much ends there; I cannot access anymore of the printer settings, etc. (i.g. scanner, fax, wifi settings, etc.) I should suffice for now as I'm satisfied with the printer's features (and size, and prince), but if I could have a full-linux-supported printer like that one, I would return this one in exchange for the other.

  Read the article

< Previous Page | 97 98 99 100 101 102 103 104 105 106 107 108  | Next Page >