Search Results

Search found 27428 results on 1098 pages for 'copy local'.

Page 1014/1098 | < Previous Page | 1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 | Next Page >

Errors when switching to specific static IP

- by michaelc

I had a Fedora box running using my static IP 69.169.136.6, etc, all configured according to what the ISP required. Just recently the hard drive failed (and I should have been keeping better backups) - while it is being recovered I would like to put up a webpage on my Archlinux PC explaining the problem - I presently do not have sufficient access to change the DNS record assigned to the domain. When I change my ip address while my system is running to 69.169.136.6, ifconfig reports the new ip address, but http://whatismyip.com/ does not. When I change it and reboot, I can't ping - the message I recieve is "connect: Network is unreachable" (when given one of google.com 's IP addresses - hostnames give me ping: unknown host xxx). Until I have access to the DNS system, what can I do to make this work? Edit: With new IP address, same problem, IP is now 69.169.136.29. Some commands might be useful: #ping 69.169.136.1 PING 69.169.136.1 (69.169.136.1) 56(84) bytes of data. 64 bytes from 69.169.136.1: icmp_seq=1 ttl=64 time=0.377 ms #ping 69.169.190.211 connect: Network is unreachable #ping 208.72.160.67 connect: Network is unreachable #ifconfig eth0 Link encap:Ethernet HWaddr 00:E0:4D:97:23:9B inet addr:69.169.136.29 Bcast:69.169.137.255 Mask:255.255.254.0 inet6 addr: fe80::2e0:4dff:fe97:239b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:132091 errors:0 dropped:0 overruns:0 frame:0 TX packets:17 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9635179 (9.1 Mb) TX bytes:1322 (1.2 Kb) Interrupt:29 Base address:0x6000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:48 errors:0 dropped:0 overruns:0 frame:0 TX packets:48 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2480 (2.4 Kb) TX bytes:2480 (2.4 Kb) #ip route 69.169.136.0/23 dev eth0 proto kernel scope link src 69.169.136.29 #cat /etc/resolv.conf # Generated by dhcpcd #nameserver 208.67.222.222 #nameserver 208.67.220.220 nameserver 69.169.190.211 nameserver 208.72.160.67 # /etc/resolv.conf.tail can replace this line Update: have new static IP addresses, verified to work in Windows... Relevant portions of /etc/rc.conf below: #Static IP example #eth0="eth0 69.169.136.6 netmask 255.255.254.0 broadcast 69.169.136.1" #eth0="eth0 69.169.136.29 netmask 255.255.254.0 broadcast 69.169.137.255" eth0="eth0 69.169.136.32 netmask 255.255.254.0 broadcast 69.169.137.255" #eth0="dhcp" INTERFACES=(eth0) # Routes to start at boot-up (in this order) # Declare each route then list in ROUTES # - prefix an entry in ROUTES with a ! to disable it # #gateway="default gw 192.168.0.1" gateway="default gw 69.169.136.1" #gateway="69.169.136.1" ROUTES=(!gateway) #ROUTES=()

Read the article
Can't add client machine to windows server 2008 domain controller

- by Patrick J Collins

A bit of background before I dive into the gritty details: I have a single server running Windows 2003 Server where I host my ASP.net website and SQL Server + Reports. I've been creating ordinary windows user accounts to authenticate my users, and I enabled integrated windows authentication with impersonation. I've set up a bunch of user groups which correspond to certain roles (admin, power user, normal user, etc) and I test membership to enable or disable certain features. Overall, I'm pretty happy with the solution, it was quick to setup and I don't have to worry about messing around storing passwords and whatnot. Well, what I'm trying to do now is set up a new environment with 3 servers (Web, SQL, Reports) and I'd like these three servers to share common user accounts. I understand that I could add these three machines to a domain, which means installing Active Directory on one of the machines. I am barking up the wrong tree here? Would you suggest an alternative configuration? Assuming that I stick with AD, I have a couple of questions regarding DNS. To be honest, I'd rather not fiddle around with the DNS settings because my ISP already has their own DNS server which works just fine. It would appear however that DNS and AD are intertwined. Firstly, if I am to create a new domain in called mycompany.net, do I actually need to be the registered owner of that domain name and ensure the DNS entry points to the IP address of the machine hosting AD? Secondly, for the two other machines that I am trying to add to the domain, do I need to fiddle with their DNS settings? I've tried setting the preferred DNS Server IP address to that of my newly installed AD, but no luck. At this point, I can't add the two other machines to the domain. Here are some diagnostics that I have run based on a few suggestions I read on forums (sorry they're in French, although I could translate if needed). I ran nltest, which seems to indicate that the client can discover the domain controller. When I run dcdiag, the call to DsGetDcName fails with error 1722, not really sure what that means. Any suggestions? Thanks! C:\Users\Administrator>nltest /dsgetdc:mycompany.net Contrôleur de domaine : \\REPORTS.mycompany.net Adresse : \\111.111.111.111 GUID dom : 3333a4ec-ca56-4f02-bb9e-76c29c6c3832 Nom dom : mycompany.net Nom de la forêt : mycompany.net Nom de site du contrôleur de domaine : Default-First-Site-Name Nom de notre site : Default-First-Site-Name Indicateurs : PDC GC DS LDAP KDC TIMESERV WRITABLE DNS_DC DNS_DOMAIN DNS _FOREST CLOSE_SITE FULL_SECRET La commande a été correctement exécutée C:\Users\Administrator>dcdiag /s:mycompany.net /u: mycompany.net \pcollins /p:somepass Diagnostic du serveur d'annuaire Exécution de l'installation initiale : * Forêt AD identifiée. Collecte des informations initiales terminée. Exécution des tests initiaux nécessaires Test du serveur : Default-First-Site-Name\REPORTS Démarrage du test : Connectivity ......................... Le test Connectivity de REPORTS a réussi Exécution des tests principaux Test du serveur : Default-First-Site-Name\REPORTS Démarrage du test : Advertising Erreur irrécupérable : l'appel DsGetDcName (REPORTS) a échoué ; erreur 1722 Le localisateur n'a pas pu trouver le serveur. ......................... Le test Advertising de REPORTS a échoué Démarrage du test : FrsEvent Impossible d'interroger le journal des événements File Replication Service sur le serveur REPORTS.mycompany.net. Erreur 0x6ba « Le serveur RPC n'est pas disponible. » ......................... Le test FrsEvent de REPORTS a échoué Démarrage du test : DFSREvent Impossible d'interroger le journal des événements DFS Replication sur le serveur REPORTS.mycompany.net. Erreur 0x6ba « Le serveur RPC n'est pas disponible. » ......................... Le test DFSREvent de REPORTS a échoué Démarrage du test : SysVolCheck [REPORTS] Une opération net use ou LsaPolicy a échoué avec l'erreur 53, Le chemin réseau n'a pas été trouvé.. ......................... Le test SysVolCheck de REPORTS a échoué Démarrage du test : KccEvent Impossible d'interroger le journal des événements Directory Service sur le serveur REPORTS.mycompany.net. Erreur 0x6ba « Le serveur RPC n'est pas disponible. » ......................... Le test KccEvent de REPORTS a échoué Démarrage du test : KnowsOfRoleHolders ......................... Le test KnowsOfRoleHolders de REPORTS a réussi Démarrage du test : MachineAccount Impossible d'ouvrir le canal avec [REPORTS] : échec avec l'erreur 53 : Le chemin réseau n'a pas été trouvé. Impossible d'obtenir le nom de domaine NetBIOS Échec : impossible de tester le nom principal de service (SPN) HOST Échec : impossible de tester le nom principal de service (SPN) HOST ......................... Le test MachineAccount de REPORTS a réussi Démarrage du test : NCSecDesc ......................... Le test NCSecDesc de REPORTS a réussi Démarrage du test : NetLogons [REPORTS] Une opération net use ou LsaPolicy a échoué avec l'erreur 53, Le chemin réseau n'a pas été trouvé.. ......................... Le test NetLogons de REPORTS a échoué Démarrage du test : ObjectsReplicated ......................... Le test ObjectsReplicated de REPORTS a réussi Démarrage du test : Replications ......................... Le test Replications de REPORTS a réussi Démarrage du test : RidManager ......................... Le test RidManager de REPORTS a réussi Démarrage du test : Services Impossible d'ouvrir IPC distant à [REPORTS.mycompany.net] : erreur 0x35 « Le chemin réseau n'a pas été trouvé. » ......................... Le test Services de REPORTS a échoué Démarrage du test : SystemLog Impossible d'interroger le journal des événements System sur le serveur REPORTS.mycompany.net. Erreur 0x6ba « Le serveur RPC n'est pas disponible. » ......................... Le test SystemLog de REPORTS a échoué Démarrage du test : VerifyReferences ......................... Le test VerifyReferences de REPORTS a réussi Exécution de tests de partitions sur ForestDnsZones Démarrage du test : CheckSDRefDom ......................... Le test CheckSDRefDom de ForestDnsZones a réussi Démarrage du test : CrossRefValidation ......................... Le test CrossRefValidation de ForestDnsZones a réussi Exécution de tests de partitions sur DomainDnsZones Démarrage du test : CheckSDRefDom ......................... Le test CheckSDRefDom de DomainDnsZones a réussi Démarrage du test : CrossRefValidation ......................... Le test CrossRefValidation de DomainDnsZones a réussi Exécution de tests de partitions sur Schema Démarrage du test : CheckSDRefDom ......................... Le test CheckSDRefDom de Schema a réussi Démarrage du test : CrossRefValidation ......................... Le test CrossRefValidation de Schema a réussi Exécution de tests de partitions sur Configuration Démarrage du test : CheckSDRefDom ......................... Le test CheckSDRefDom de Configuration a réussi Démarrage du test : CrossRefValidation ......................... Le test CrossRefValidation de Configuration a réussi Exécution de tests de partitions sur mycompany Démarrage du test : CheckSDRefDom ......................... Le test CheckSDRefDom de mycompany a réussi Démarrage du test : CrossRefValidation ......................... Le test CrossRefValidation de mycompany a réussi Exécution de tests d'entreprise sur mycompany.net Démarrage du test : LocatorCheck Avertissement : l'appel DcGetDcName(GC_SERVER_REQUIRED) a échoué ; erreur 1722 Serveur de catalogue global introuvable - Les catalogues globaux ne fonctionnent pas. Avertissement : l'appel DcGetDcName(PDC_REQUIRED) a échoué ; erreur 1722 Contrôleur principal de domaine introuvable. Le serveur contenant le rôle PDC ne fonctionne pas. Avertissement : l'appel DcGetDcName(TIME_SERVER) a échoué ; erreur 1722 Serveur de temps introuvable. Le serveur contenant le rôle PDC ne fonctionne pas. Avertissement : l'appel DcGetDcName(GOOD_TIME_SERVER_PREFERRED) a échoué ; erreur 1722 Serveur de temps introuvable. Avertissement : l'appel DcGetDcName(KDC_REQUIRED) a échoué ; erreur 1722 Centre de distribution de clés introuvable : les centres de distribution de clés ne fonctionnent pas. ......................... Le test LocatorCheck de mycompany.net a échoué Démarrage du test : Intersite ......................... Le test Intersite de mycompany.net a réussi Update 1 : I am under the distinct impression that the problem is caused by some security settings. I have read elsewhere that the client needs to be able to access the fileshare sysvol. I had to enable Client for Microsoft Windows and File and Printer Sharing which were previously disabled. When I now run dcdiag the Advertising test works, which I suppose is forward progress. It currently chokes on the Services step (unable to open remote IPC). Démarrage du test : Services Impossible d'ouvrir IPC distant à [REPORTS.locbus.net] : erreur 0x35 « Le chemin réseau n'a pas été trouvé. » ......................... Le test Services de REPORTS a échoué The original English version of that error message : Could not open Remote ipc to [server] Update 2 : I attach some more diagnostics : Netsetup.log (client): 09/24/2009 13:27:09:773 ----------------------------------------------------------------- 09/24/2009 13:27:09:773 NetpValidateName: checking to see if 'WEB' is valid as type 1 name 09/24/2009 13:27:12:773 NetpCheckNetBiosNameNotInUse for 'WEB' [MACHINE] returned 0x0 09/24/2009 13:27:12:773 NetpValidateName: name 'WEB' is valid for type 1 09/24/2009 13:27:12:805 ----------------------------------------------------------------- 09/24/2009 13:27:12:805 NetpValidateName: checking to see if 'WEB' is valid as type 5 name 09/24/2009 13:27:12:805 NetpValidateName: name 'WEB' is valid for type 5 09/24/2009 13:27:12:852 ----------------------------------------------------------------- 09/24/2009 13:27:12:852 NetpValidateName: checking to see if 'MYCOMPANY.NET' is valid as type 3 name 09/24/2009 13:27:12:992 NetpCheckDomainNameIsValid [ Exists ] for 'MYCOMPANY.NET' returned 0x0 09/24/2009 13:27:12:992 NetpValidateName: name 'MYCOMPANY.NET' is valid for type 3 09/24/2009 13:27:21:320 ----------------------------------------------------------------- 09/24/2009 13:27:21:320 NetpDoDomainJoin 09/24/2009 13:27:21:320 NetpMachineValidToJoin: 'WEB' 09/24/2009 13:27:21:320 OS Version: 6.0 09/24/2009 13:27:21:320 Build number: 6002 09/24/2009 13:27:21:320 ServicePack: Service Pack 2 09/24/2009 13:27:21:414 SKU: Windows Server® 2008 Standard 09/24/2009 13:27:21:414 NetpDomainJoinLicensingCheck: ulLicenseValue=1, Status: 0x0 09/24/2009 13:27:21:414 NetpGetLsaPrimaryDomain: status: 0x0 09/24/2009 13:27:21:414 NetpMachineValidToJoin: status: 0x0 09/24/2009 13:27:21:414 NetpJoinDomain 09/24/2009 13:27:21:414 Machine: WEB 09/24/2009 13:27:21:414 Domain: MYCOMPANY.NET 09/24/2009 13:27:21:414 MachineAccountOU: (NULL) 09/24/2009 13:27:21:414 Account: MYCOMPANY.NET\pcollins 09/24/2009 13:27:21:414 Options: 0x25 09/24/2009 13:27:21:414 NetpLoadParameters: loading registry parameters... 09/24/2009 13:27:21:414 NetpLoadParameters: DNSNameResolutionRequired not found, defaulting to '1' 0x2 09/24/2009 13:27:21:414 NetpLoadParameters: status: 0x2 09/24/2009 13:27:21:414 NetpValidateName: checking to see if 'MYCOMPANY.NET' is valid as type 3 name 09/24/2009 13:27:21:523 NetpCheckDomainNameIsValid [ Exists ] for 'MYCOMPANY.NET' returned 0x0 09/24/2009 13:27:21:523 NetpValidateName: name 'MYCOMPANY.NET' is valid for type 3 09/24/2009 13:27:21:523 NetpDsGetDcName: trying to find DC in domain 'MYCOMPANY.NET', flags: 0x40001010 09/24/2009 13:27:22:039 NetpDsGetDcName: failed to find a DC having account 'WEB$': 0x525, last error is 0x79 09/24/2009 13:27:22:039 NetpDsGetDcName: status of verifying DNS A record name resolution for 'KING.MYCOMPANY.NET': 0x0 09/24/2009 13:27:22:039 NetpDsGetDcName: found DC '\\KING.MYCOMPANY.NET' in the specified domain 09/24/2009 13:27:30:039 NetUseAdd to \\KING.MYCOMPANY.NET\IPC$ returned 53 09/24/2009 13:27:30:039 NetpJoinDomain: status of connecting to dc '\\KING.MYCOMPANY.NET': 0x35 09/24/2009 13:27:30:039 NetpDoDomainJoin: status: 0x35 09/24/2009 13:27:30:148 ----------------------------------------------------------------- ipconfig /all (on client): Configuration IP de Windows Nom de l'hôte . . . . . . . . . . : WEB Suffixe DNS principal . . . . . . : Type de noeud. . . . . . . . . . : Hybride Routage IP activé . . . . . . . . : Non Proxy WINS activé . . . . . . . . : Non Carte Ethernet Connexion au réseau local : Suffixe DNS propre à la connexion. . . : Description. . . . . . . . . . . . . . : Intel 21140-Based PCI Fast Ethernet Adapter (Emulated) Adresse physique . . . . . . . . . . . : **-15-5D-A1-17-** DHCP activé. . . . . . . . . . . . . . : Non Configuration automatique activée. . . : Oui Adresse IPv4. . . . . . . . . . . : **.***.163.122(préféré) Masque de sous-réseau. . . . . . . . . : 255.255.255.0 Passerelle par défaut. . . . . . . . . : **.***.163.2 Serveurs DNS. . . . . . . . . . . . . : **.***.163.123 NetBIOS sur Tcpip. . . . . . . . . . . : Activé ipconfig /all (on server): Configuration IP de Windows Nom de l'hôte . . . . . . . . . . : KING Suffixe DNS principal . . . . . . : mycompany.net Type de noeud. . . . . . . . . . : Hybride Routage IP activé . . . . . . . . : Non Proxy WINS activé . . . . . . . . : Non Liste de recherche du suffixe DNS.: locbus.net Carte Ethernet Connexion au réseau local : Suffixe DNS propre à la connexion. . . : Description. . . . . . . . . . . . . . : Intel 21140-Based PCI Fast Ethernet Adapter (Emulated) Adresse physique . . . . . . . . . . . : **-15-5D-A1-1E-** DHCP activé. . . . . . . . . . . . . . : Non Configuration automatique activée. . . : Oui Adresse IPv4. . . . . . . . . . . : **.***.163.123(préféré) Masque de sous-réseau. . . . . . . . . : 255.255.255.0 Passerelle par défaut. . . . . . . . . : **.***.163.2 Serveurs DNS. . . . . . . . . . . . . : 127.0.0.1 NetBIOS sur Tcpip. . . . . . . . . . . : Activé nslookup (on client): Serveur : *******.***.com Address: **.***.163.123 Nom : mycompany.net Addresses: ****:****:a37b::****:a37b **.****.163.123

Read the article
Encouter error "Linux ip -6 addr add failed" while setting up OpenVPN client

- by Mickel

I am trying to set up my router to use OpenVPN and have gotten quite far (I think), but something seems to be missing and I am not sure what. Here is my configuration for the client: client dev tun proto udp remote ovpn.azirevpn.net 1194 remote-random resolv-retry infinite auth-user-pass /tmp/password.txt nobind persist-key persist-tun ca /tmp/AzireVPN.ca.crt remote-cert-tls server reneg-sec 0 verb 3 OpenVPN client log: Nov 8 15:45:13 rc_service: httpd 15776:notify_rc start_vpnclient1 Nov 8 15:45:14 openvpn[27196]: OpenVPN 2.3.2 arm-unknown-linux-gnu [SSL (OpenSSL)] [LZO] [EPOLL] [MH] [IPv6] built on Nov 1 2013 Nov 8 15:45:14 openvpn[27196]: NOTE: the current --script-security setting may allow this configuration to call user-defined scripts Nov 8 15:45:14 openvpn[27196]: Socket Buffers: R=[116736->131072] S=[116736->131072] Nov 8 15:45:14 openvpn[27202]: UDPv4 link local: [undef] Nov 8 15:45:14 openvpn[27202]: UDPv4 link remote: [AF_INET]178.132.75.14:1194 Nov 8 15:45:14 openvpn[27202]: TLS: Initial packet from [AF_INET]178.132.75.14:1194, sid=44d80db5 8b36adf9 Nov 8 15:45:14 openvpn[27202]: WARNING: this configuration may cache passwords in memory -- use the auth-nocache option to prevent this Nov 8 15:45:14 openvpn[27202]: VERIFY OK: depth=1, C=RU, ST=Moscow, L=Moscow, O=Azire Networks, OU=VPN, CN=Azire Networks, name=Azire Networks, [email protected] Nov 8 15:45:14 openvpn[27202]: Validating certificate key usage Nov 8 15:45:14 openvpn[27202]: ++ Certificate has key usage 00a0, expects 00a0 Nov 8 15:45:14 openvpn[27202]: VERIFY KU OK Nov 8 15:45:14 openvpn[27202]: Validating certificate extended key usage Nov 8 15:45:14 openvpn[27202]: ++ Certificate has EKU (str) TLS Web Server Authentication, expects TLS Web Server Authentication Nov 8 15:45:14 openvpn[27202]: VERIFY EKU OK Nov 8 15:45:14 openvpn[27202]: VERIFY OK: depth=0, C=RU, ST=Moscow, L=Moscow, O=AzireVPN, OU=VPN, CN=ovpn, name=ovpn, [email protected] Nov 8 15:45:15 openvpn[27202]: Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Nov 8 15:45:15 openvpn[27202]: Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Nov 8 15:45:15 openvpn[27202]: Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Nov 8 15:45:15 openvpn[27202]: Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Nov 8 15:45:15 openvpn[27202]: Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 2048 bit RSA Nov 8 15:45:15 openvpn[27202]: [ovpn] Peer Connection Initiated with [AF_INET]178.132.75.14:1194 Nov 8 15:45:17 openvpn[27202]: SENT CONTROL [ovpn]: 'PUSH_REQUEST' (status=1) Nov 8 15:45:17 openvpn[27202]: PUSH: Received control message: 'PUSH_REPLY,ifconfig-ipv6 2a03:8600:1001:4010::101f/64 2a03:8600:1001:4010::1,route-ipv6 2000::/3 2A03:8600:1001:4010::1,redirect-gateway def1 bypass-dhcp,dhcp-option DNS 194.1.247.30,tun-ipv6,route-gateway 178.132.77.1,topology subnet,ping 3,ping-restart 15,ifconfig 178.132.77.33 255.255.255.192' Nov 8 15:45:17 openvpn[27202]: OPTIONS IMPORT: timers and/or timeouts modified Nov 8 15:45:17 openvpn[27202]: OPTIONS IMPORT: --ifconfig/up options modified Nov 8 15:45:17 openvpn[27202]: OPTIONS IMPORT: route options modified Nov 8 15:45:17 openvpn[27202]: OPTIONS IMPORT: route-related options modified Nov 8 15:45:17 openvpn[27202]: OPTIONS IMPORT: --ip-win32 and/or --dhcp-option options modified Nov 8 15:45:17 openvpn[27202]: TUN/TAP device tun0 opened Nov 8 15:45:17 openvpn[27202]: TUN/TAP TX queue length set to 100 Nov 8 15:45:17 openvpn[27202]: do_ifconfig, tt->ipv6=1, tt->did_ifconfig_ipv6_setup=1 Nov 8 15:45:17 openvpn[27202]: /usr/sbin/ip link set dev tun0 up mtu 1500 Nov 8 15:45:18 openvpn[27202]: /usr/sbin/ip addr add dev tun0 178.132.77.33/26 broadcast 178.132.77.63 Nov 8 15:45:18 openvpn[27202]: /usr/sbin/ip -6 addr add 2a03:8600:1001:4010::101f/64 dev tun0 Nov 8 15:45:18 openvpn[27202]: Linux ip -6 addr add failed: external program exited with error status: 254 Nov 8 15:45:18 openvpn[27202]: Exiting due to fatal error Any ideas are most welcome!

Read the article
SQL Server Agent was not running on Server Dynamics CRM 2013

- by No1_Melman

I'm trying to install Dynamics CRM 2013 on a server. This server is on a VM. There are several other VMs, an ADDS & DNS, a MSSQL and a WebServer VM. Each server is a Windows Server 2012 R2. The SQL Server is 2012 Enterprise. Each VM is part of the main Domain, set by the ADDS & DNS. NSLookup confirms I can see the computer at the right IP address. Each separate VM has its own static IP, the DNS is set to the ADDS & DNS. I use the domain administrator to log into all the servers, and make the that domain administrator a local administrator. I've set up all the domain users for the CRM and gave them appropriate permissions, I have also added the accounts to the appropriate places, such that the CRM Deployment user is in the SQL security. The SQL Agent is running. SQL server configuration manager has SQL server network configuration TCP/IP enabled to allow remote connections. The SQL server has the domain user as a administrator, which is the same user being used to install the CRM. In the CRM setup i point to the [Servername]\[Instance] and I have also tried just the [Servername]. to make this easier I called the server MSSQL and left the instance name to the default. I even install the MSSQL instance as the domain administrator. CRM can find the ReportServer url. I have enable all the ports required, including: 135, 1433, 1434, 2382, 2383, 4022. 1434 UDP. I feel like I have absolutely done everything, I have google many times and tried all the different methods, and for the life of me I cant seem to get the CRM setup to find the SQL server agent. It passes everything else perfectly fine. I can even ping the MSSQL server. What is the problem, why does the CRM still keep giving the error: SQLSERVERAGENT (SQLSERVERAGENT) service is not running on the server MSSQL On the MSSQL server, the name of the sql server agent service is: SQL Server Agent (MSSQLSERVER)

Read the article
Cacti: "An internal Net-Snmp error condition detected in Cacti snmp_count"

- by Recc

There's the odd forum topic about an error similarly obscure as this, but I haven't seen any for snmp_count in particular. Also I don't see graphing problems, though I can't simply go and eyeball all graphs. However the poller does time out and has to be stopped by its internal process preventing overruns. If I filter out the flood of this error in the log I dont get anything else except the poller timeout: 06/12/2014 12:48:00 PM - POLLER: Poller[0] Maximum runtime of 58 seconds exceeded. Exiting. 06/12/2014 12:48:00 PM - SYSTEM STATS: Time:58.8566 Method:spine Processes:1 Threads:40 Hosts:1923 HostsPerProcess:1923 DataSources:61584 RRDsProcessed:0 06/12/2014 12:48:00 PM - SPINE: Poller[0] ERROR: Spine Timed Out While Processing Hosts Internal I saw in the running processes /usr/local/spine/spine 0 2053 that's always left behind. When I kill it the flooding of the error stops. Of course it's the same on the next poll run as it goes through the devices. 2053 is apparently the DB ID for a device. I deleted it completely to see if that stops it. It doesn't, instead 2052 is seen there. I suspect It'll be the same if I keep deleting devices which I will not do. This started happening midday when I wasn't doing anything to the cacti server. I have tried reducing Maximum Threads per Process to 1 and Number of PHP Script Servers to 1. I've been running it at 10 script servers / 40 threads for months with poll cycle time of about 20 sec. I just found out Running snmpwalk on any host would begin returning the values but then timeout halfway through. This doesn't happen from different servers on the network this Cacti is suggesting still that it's a problem with it locally. Any suggestions? For one polling cycle I changed to use cmd.php instead. then I started getting errors like CMDPHP: Poller[0] Host[45] DS[541] WARNING: Result from SNMP not valid. Partial Result: U Perhaps as expected. Looking closely I see that every snmpwalk I do is interrupted at the same place as if some byte limit is hit and the connection torn down.

Read the article
Fedora 12 Wireless problems (Intel Wireless 4965AGN Card)

- by Ninefingers

Hi All, I'm having an interesting experience with my wireless card at the moment. Basically, it does like this: I connect to the local wireless network (netgear router) It works, briefly, allowing me to browse a webpage or maybe two, if I'm lucky. It then stops working / sending any packets, whilst reported still connected. Now, me being me I've had a look to see what I can find. wpa_supplicant.log looks like this: Trying to associate with valid_mac:a2:30 (SSID='vennardwireless' freq=2462 MHz) Associated with valid_mac:a2:30 WPA: Key negotiation completed with valid_mac:a2:30 [PTK=CCMP GTK=TKIP] CTRL-EVENT-CONNECTED - Connection to valid_mac:a2:30 completed (reauth) [id=0 id_str=] CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys So that's working fine. dmesg | grep "*iwl*" spits out this: iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27kds iwlagn: Copyright(c) 2003-2009 Intel Corporation iwlagn 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 iwlagn 0000:03:00.0: setting latency timer to 64 iwlagn 0000:03:00.0: Detected Intel Wireless WiFi Link 4965AGN REV=0x4 iwlagn 0000:03:00.0: Tunable channels: 13 802.11bg, 19 802.11a channels iwlagn 0000:03:00.0: irq 32 for MSI/MSI-X phy0: Selected rate control algorithm 'iwl-agn-rs' iwlagn 0000:03:00.0: firmware: requesting iwlwifi-4965-2.ucode iwlagn 0000:03:00.0: loaded firmware version 228.61.2.24 Registered led device: iwl-phy0::radio Registered led device: iwl-phy0::assoc Registered led device: iwl-phy0::RX Registered led device: iwl-phy0::TX iwlagn 0000:03:00.0: iwl_tx_agg_start on ra = 00:24:b2:32:a3:30 tid = 0 iwlagn 0000:03:00.0: iwl_tx_agg_start on ra = 00:24:b2:32:a3:30 tid = 0 So that's working too. I can also ping 192.168.0.1 -I wlan0 and arping 192.168.0.1 -I wlan0 the router until the network falls over. uname -r:2.6.32.10-90.fc12.x86_64. Laptop is a Core2 Duo (2Ghz) with 3GB RAM. Other symptoms I've noticed are that wireshark freezes when I capture on the "broken" interface until I disconnect. Am using networkmanager as per normal. Stupidly, I can connect to the same router via eth0/a cat6 cable just fine. Everyone else can connect to the AP fine (from Windows). Yes, I'm sat right next to it and not trying to access a hotspot the other side of the world. Any ideas? Is this a broken update? (I intend to reboot and test an older kernel later)? Anyone else come across this? Edit: iwconfig wlan0 rate auto is the settings I'm using for rates. Also, according to networkmanager the network is still connected. Thanks for any pointers / advice.

Read the article
Globe SSL with NGINX SSL certificate problem, please help

- by PartySoft

I have a big problem with installing a certificat for nginx (same happends with apache though) I have 3 files __domain_com.crt __domain_com.ca-bundle and ssl.key. I tried to append cat __domain_com.crt __leechpack_com.ca-bundle bundle.crt but if I do it like this i get an error: [emerg]: SSL_CTX_use_certificate_chain_file("/etc/nginx/__leechpack_com.crt") failed (SSL: error:0906D066:PEM routines:PEM_read_bio:bad end line error:140DC009:SSL routines:SSL_CTX_use_certificate_chain_file:PEM lib) And that's because the delimiters of the certificates arren't separated. ZqTjb+WBJQ== -----END CERTIFICATE----------BEGIN CERTIFICATE----- MIIE6DCCA9CgAwIBAgIQdIYhlpUQySkmKUvMi/gpLDANBgkqhkiG9w0BAQUFADBv If i separate them with an enter between certificated it will at least start but i will get the same warning from Firefox: This Connection is Untrusted You have asked Firefox to connect securely to domain.com, but we can't confirm that your connection is secure. The concatenate solution it is given by Globe SSL and the NGINX site but it doesn't work. I think the bundle is ignored though. http://customer.globessl.com/knowledgebase/55/Certificate-Installation--Nginx.html http://nginx.org/en/docs/http/configuring_https_servers.html#chains%20http://wiki.nginx.org/NginxHttpSslModule if i do openssl s_client -connect down.leechpack.com:443 CONNECTED(00000003) depth=0 /OU=Domain Control Validated/OU=Provided by Globe Hosting, Inc./OU=Globe Standard Wildcard SSL/CN=*.domain.com verify error:num=20:unable to get local issuer certificate verify return:1 depth=0 /OU=Domain Control Validated/OU=Provided by Globe Hosting, Inc./OU=Globe Standard Wildcard SSL/CN=*.domain.com verify error:num=27:certificate not trusted verify return:1 depth=0 /OU=Domain Control Validated/OU=Provided by Globe Hosting, Inc./OU=Globe Standard Wildcard SSL/CN=*.domain.com verify error:num=21:unable to verify the first certificate verify return:1 --- Certificate chain 0 s:/OU=Domain Control Validated/OU=Provided by Globe Hosting, Inc./OU=Globe Standard Wildcard SSL/CN=*.domain.com i:/C=RO/O=GLOBE HOSTING CERTIFICATION AUTHORITY/CN=GLOBE SSL Domain Validated CA 1 s:/C=US/O=Globe Hosting, Inc./OU=GlobeSSL DV Certification Authority/CN=GlobeSSL CA i:/C=SE/O=AddTrust AB/OU=AddTrust External TTP Network/CN=AddTrust External CA Root --- Server certificate -----BEGIN CERTIFICATE----- MIIFQzCCBCugAwIBAgIQRnpCmtwX7z7GTla0QktE6DANBgkqhkiG9w0BAQUFADBl MQswCQYDVQQGEwJSTzEuMCwGA1UEChMlR0xPQkUgSE9TVElORyBDRVJUSUZJQ0FU SU9OIEFVVEhPUklUWTEmMCQGA1UEAxMdR0xPQkUgU1NMIERvbWFpbiBWYWxpZGF0 ZWQgQ0EwHhcNMTAwMjExMDAwMDAwWhcNMTEwMjExMjM1OTU5WjCBjTEhMB8GA1UE CxMYRG9tYWluIENvbnRyb2wgVmFsaWRhdGVkMSgwJgYDVQQLEx9Qcm92aWRlZCBi eSBHbG9iZSBIb3N0aW5nLCBJbmMuMSQwIgYDVQQLExtHbG9iZSBTdGFuZGFyZCBX aWxkY2FyZCBTU0wxGDAWBgNVBAMUDyoubGVlY2hwYWNrLmNvbTCCASIwDQYJKoZI hvcNAQEBBQADggEPADCCAQoCggEBAKX7jECMlYEtcvqVWQVUpXNxO/VaHELghqy/ Ml8dOfOXG29ZMZsKUMqS0jXEwd+Bdpm31lBxOALkj8o79hX0tspLMjgtCnreaker 49y62BcjfguXRFAaiseXTNbMer5lDWiHlf1E7uCoTTiczGqBNfl6qSJlpe4rYBtq XxBAiygaNba6Owghuh19+Uj8EICb2pxbJNFfNzU1D9InFdZSVqKHYBem4Cdrtxua W4+YONsfLnnfkRQ6LOLeYExHziTQhSavSv9XaCl9Zqzm5/eWbQqLGRpSJoEPY/0T GqnmeMIq5M35SWZgOVV10j3pOCS8o0zpp7hMJd2R/HwVaPCLjukCAwEAAaOCAcQw ggHAMB8GA1UdIwQYMBaAFB9UlnKtPUDnlln3STFTCWb5DWtyMB0GA1UdDgQWBBT0 8rPIMr7JDa2Xs5he5VXAvMWArjAOBgNVHQ8BAf8EBAMCBaAwDAYDVR0TAQH/BAIw ADAdBgNVHSUEFjAUBggrBgEFBQcDAQYIKwYBBQUHAwIwVQYDVR0gBE4wTDBKBgsr BgEEAbIxAQICGzA7MDkGCCsGAQUFBwIBFi1odHRwOi8vd3d3Lmdsb2Jlc3NsLmNv bS9kb2NzL0dsb2JlU1NMX0NQUy5wZGYwRgYDVR0fBD8wPTA7oDmgN4Y1aHR0cDov L2NybC5nbG9iZXNzbC5jb20vR0xPQkVTU0xEb21haW5WYWxpZGF0ZWRDQS5jcmww dwYIKwYBBQUHAQEEazBpMEEGCCsGAQUFBzAChjVodHRwOi8vY3J0Lmdsb2Jlc3Ns LmNvbS9HTE9CRVNTTERvbWFpblZhbGlkYXRlZENBLmNydDAkBggrBgEFBQcwAYYY aHR0cDovL29jc3AuZ2xvYmVzc2wuY29tMCkGA1UdEQQiMCCCDyoubGVlY2hwYWNr LmNvbYINbGVlY2hwYWNrLmNvbTANBgkqhkiG9w0BAQUFAAOCAQEAB2Y7vQsq065K s+/n6nJ8ZjOKbRSPEiSuFO+P7ovlfq9OLaWRHUtJX0sLntnWY1T9hVPvS5xz/Ffl w9B8g/EVvvfMyOw/5vIyvHq722fAAC1lWU1rV3ww0ng5bgvD20AgOlIaYBvRq8EI 5Dxo2og2T1UjDN44GOSWsw5jetvVQ+SPeNPQLWZJS9pNCzFQ/3QDWNPOvHqEeRcz WkOTCqbOSZYvoSPvZ3APh+1W6nqiyoku/FCv9otSCtXPKtyVa23hBQ+iuxqIM4/R gncnUKASi6KQrWMQiAI5UDCtq1c09uzjw+JaEzAznxEgqftTOmXAJSQGqZGd6HpD ZqTjb+WBJQ== -----END CERTIFICATE----- subject=/OU=Domain Control Validated/OU=Provided by Globe Hosting, Inc./OU=Globe Standard Wildcard SSL/CN=*.domain.com issuer=/C=RO/O=GLOBE HOSTING CERTIFICATION AUTHORITY/CN=GLOBE SSL Domain Validated CA --- No client certificate CA names sent --- SSL handshake has read 3313 bytes and written 343 bytes --- New, TLSv1/SSLv3, Cipher is DHE-RSA-AES256-SHA Server public key is 2048 bit Secure Renegotiation IS supported Compression: NONE Expansion: NONE SSL-Session: Protocol : TLSv1 Cipher : DHE-RSA-AES256-SHA Session-ID: 5F9C8DC277A372E28A4684BAE5B311533AD30E251369D144A13DECA3078E067F Session-ID-ctx: Master-Key: 9B531A75347E6E7D19D95365C1208F2ED37E4004AA8F71FC614A18937BEE2ED9F82D58925E0B3931492AD3D2AA6EFD3B Key-Arg : None Start Time: 1288618211 Timeout : 300 (sec) Verify return code: 21 (unable to verify the first certificate) ---

Read the article
JVM process resident set size "equals" max heap size, not current heap size

- by Volune

After a few reading about jvm memory (here, here, here, others I forgot...), I am expecting the resident set size of my java process to be roughly equal to the current heap space capacity. That's not what the numbers are saying, it seems to be roughly equal to the max heap space capacity: Resident set size: # echo 0 $(cat /proc/1/smaps | grep Rss | awk '{print $2}' | sed 's#^#+#') | bc 11507912 # ps -C java -O rss | gawk '{ count ++; sum += $2 }; END {count --; print "Number of processes =",count; print "Memory usage per process =",sum/1024/count, "MB"; print "Total memory usage =", sum/1024, "MB" ;};' Number of processes = 1 Memory usage per process = 11237.8 MB Total memory usage = 11237.8 MB Java heap # jmap -heap 1 Attaching to process ID 1, please wait... Debugger attached successfully. Server compiler detected. JVM version is 24.55-b03 using thread-local object allocation. Garbage-First (G1) GC with 18 thread(s) Heap Configuration: MinHeapFreeRatio = 10 MaxHeapFreeRatio = 20 MaxHeapSize = 10737418240 (10240.0MB) NewSize = 1363144 (1.2999954223632812MB) MaxNewSize = 17592186044415 MB OldSize = 5452592 (5.1999969482421875MB) NewRatio = 2 SurvivorRatio = 8 PermSize = 20971520 (20.0MB) MaxPermSize = 85983232 (82.0MB) G1HeapRegionSize = 2097152 (2.0MB) Heap Usage: G1 Heap: regions = 2560 capacity = 5368709120 (5120.0MB) used = 1672045416 (1594.586769104004MB) free = 3696663704 (3525.413230895996MB) 31.144272834062576% used G1 Young Generation: Eden Space: regions = 627 capacity = 3279945728 (3128.0MB) used = 1314914304 (1254.0MB) free = 1965031424 (1874.0MB) 40.089514066496164% used Survivor Space: regions = 49 capacity = 102760448 (98.0MB) used = 102760448 (98.0MB) free = 0 (0.0MB) 100.0% used G1 Old Generation: regions = 147 capacity = 1986002944 (1894.0MB) used = 252273512 (240.5867691040039MB) free = 1733729432 (1653.413230895996MB) 12.702574926293766% used Perm Generation: capacity = 39845888 (38.0MB) used = 38884120 (37.082786560058594MB) free = 961768 (0.9172134399414062MB) 97.58628042120682% used 14654 interned Strings occupying 2188928 bytes. Are my expectations wrong? What should I expect? I need the heap space to be able to grow during spikes (to avoid very slow Full GC), but I would like to have the resident set size as low as possible the rest of the time, to benefit the other processes running on the server. Is there a better way to achieve that? Linux 3.13.0-32-generic x86_64 java version "1.7.0_55" Running in Docker version 1.1.2 Java is running elasticsearch 1.2.0: /usr/bin/java -Xms5g -Xmx10g -XX:MinHeapFreeRatio=10 -XX:MaxHeapFreeRatio=20 -Xss256k -Djava.awt.headless=true -XX:+UseG1GC -XX:MaxGCPauseMillis=350 -XX:InitiatingHeapOccupancyPercent=45 -XX:+AggressiveOpts -XX:+UseCompressedOops -XX:-OmitStackTraceInFastThrow -XX:+PrintGCDetails -XX:+PrintGCTimeStamps -XX:+PrintClassHistogram -XX:+PrintTenuringDistribution -XX:+PrintGCApplicationStoppedTime -XX:+PrintGCApplicationConcurrentTime -Xloggc:/opt/elasticsearch/logs/gc.log -XX:+HeapDumpOnOutOfMemoryError -XX:HeapDumpPath=/opt elasticsearch/logs/heapdump.hprof -XX:ErrorFile=/opt/elasticsearch/logs/hs_err.log -Des.logger.port=99999 -Des.logger.host=999.999.999.999 -Delasticsearch -Des.foreground=yes -Des.path.home=/opt/elasticsearch -cp :/opt/elasticsearch/lib/elasticsearch-1.2.0.jar:/opt/elasticsearch/lib/*:/opt/elasticsearch/lib/sigar/* org.elasticsearch.bootstrap.Elasticsearch There actually are 5 elasticsearch nodes, each in a different docker container. All have about the same memory usage. Some stats about the index: size: 9.71Gi (19.4Gi) docs: 3,925,398 (4,052,694)

Read the article
Unable to delete a file using bash script

- by user3719091

I'm having problems removing a file in a bash script. I saw the other post with the same problem but none of those solutions solved my problem. The bash script is an OP5 surveillance check and it calls an Expect process that saves a temporary file to the local drive which the bash script reads from. Once it has read the file and checked its status I would like to remove the temporary file. I'm pretty new to scripting so my script may not be as optimal as it can be. Either way it does the job except removing the file once it's done. I will post the entire code below: #!/bin/bash #GET FLAGS while getopts H:c:w: option do case "${option}" in H) HOSTADDRESS=${OPTARG};; c) CRITICAL=${OPTARG};; w) WARNING=${OPTARG};; esac done ./expect.vpn.check.sh $HOSTADDRESS #VARIABLES VPNCount=$(grep -o '[0-9]\+' $HOSTADDRESS.op5.vpn.results) # Check if the temporary results file exists if [ -f $HOSTADDRESS.op5.vpn.results ] then # If the file exist, Print "File Found" message echo Temporary results file exist. Analyze results. else # If the file does NOT exist, print "File NOT Found" message and send message to OP5 echo Temporary results file does NOT exist. Unable to analyze. # Exit with status Critical (exit code 2) exit 2 fi if [[ "$VPNCount" > $CRITICAL ]] then # If the amount of tunnels exceeds the critical threshold, echo out a warning message and current threshold and send warning to OP5 echo "The amount of VPN tunnels exceeds the critical threshold - ($VPNCount)" # Exit with status Critical (exit code 2) exit 2 elif [[ "$VPNCount" > $WARNING ]] then # If the amount of tunnels exceeds the warning threshold, echo out a warning message and current threshold and send warning to OP5 echo "The amount of VPN tunnels exceeds the warning threshold - ($VPNCount)" # Exit with status Warning (exit code 1) exit 1 else # The amount of tunnels do not exceed the warning threshold. # Print an OK message echo OK - $VPNCount # Exit with status OK exit 0 fi #Clean up temporary files. rm -f $HOSTADDRESS.op5.vpn.results I have tried the following solutions: Create a separate variable called TempFile that specifies the file. And specify that in the rm command. I tried creating another if statement similar to the one I use to verify that file exist and then rm the filename. I tried adding the complete name of the file (no variables, just plain text of the file) I can: Remove the file using the full name in both a separate script and directly in the CLI. Is there something in my script that locks the file that prevents me from removing it? I'm not sure what to try next. Thanks in advance!

Read the article
PostgreSQL service doesn't start on Windows 7

- by Mehrdad

(Not sure if this should be on Stack Overflow or Super User... please move if needed.) When I start the PostgreSQL service on Windows 7 x64, it immediately stops. When I check my log folder (C:\PostgreSQL\9.1\data\pg_log\), I see new but empty log files. The Event Viewer doesn't tell me anything other than the fact that the server did not respond. I've even tried turning off my firewall (I don't have any antivirus or anything else), but nothing helps. The setup works fine when I'm on Windows XP (32-bit) (same computer, different partition). I can't figure out what's wrong, even though I've tried tracing the system calls. Is PostgreSQL compatible with Windows 7 x64 at all? Any ideas what the issue might be? More info: This problem also happens at the end of installation -- the service starts, then stops immediately, before the installer can do anything. Installation log: Starting the database server... Executing cscript //NoLogo "C:\Program Files\PostgreSQL\9.1\installer\server\startserver.vbs" postgresql-x64-9.1 Script exit code: 0 Script output: Starting postgresql-x64-9.1 Service postgresql-x64-9.1 started successfully // <==== NOT REALLY!! It stops! startserver.vbs ran to completion Script stderr: Loading additional SQL modules... Executing cscript //NoLogo "C:\Program Files\PostgreSQL\9.1\installer\server\loadmodules.vbs" "postgres" "****" "C:\Program Files\PostgreSQL\9.1" "C:\Program Files\PostgreSQL\9.1\data" 5432 Script exit code: 2 Script output: Installing the adminpack module in the postgres database... Executing 'C:\Users\HOMEUS~1\AppData\Local\Temp\rad6C20D.bat'... psql: could not connect to server: Connection refused (0x0000274D/10061) Is the server running on host "localhost" (::1) and accepting TCP/IP connections on port 5432? could not connect to server: Connection refused (0x0000274D/10061) Is the server running on host "localhost" (127.0.0.1) and accepting TCP/IP connections on port 5432? Failed to install the 'adminpack' module in the 'postgres' database loadmodules.vbs ran to completion Script stderr: Program ended with an error exit code Error running cscript //NoLogo "C:\Program Files\PostgreSQL\9.1\installer\server\loadmodules.vbs" "postgres" "****" "C:\Program Files\PostgreSQL\9.1" "C:\Program Files\PostgreSQL\9.1\data" 5432 : Program ended with an error exit code

Read the article
Apache-Mina FTPServer Issue — unable to login into apache ftp server while using database user manager

- by piyush

I am unable to login into apache ftp server while using database user manager: while entering username and password,I am getting following error in log file: [ INFO] 2013-02-07 20:51:07,779 [] [0:0:0:0:0:0:0:1] RECEIVED: USER piyush [ INFO] 2013-02-07 20:51:07,781 [piyush] [0:0:0:0:0:0:0:1] SENT: 331 User name okay, need password for piyush. [ INFO] 2013-02-07 20:51:07,784 [piyush] [0:0:0:0:0:0:0:1] RECEIVED: PASS ***** [ WARN] 2013-02-07 20:51:07,785 [piyush] [0:0:0:0:0:0:0:1] User failed to log in [ WARN] 2013-02-07 20:51:08,285 [piyush] [0:0:0:0:0:0:0:1] Login failure - piyush [ INFO] 2013-02-07 20:51:08,286 [piyush] [0:0:0:0:0:0:0:1] SENT: 530 Authentication failed. [ INFO] 2013-02-07 20:51:08,286 [piyush] [0:0:0:0:0:0:0:1] RECEIVED: QUIT [ INFO] 2013-02-07 20:51:08,290 [piyush] [0:0:0:0:0:0:0:1] SENT: 221 Goodbye. [ INFO] 2013-02-07 20:51:08,291 [piyush] [0:0:0:0:0:0:0:1] CLOSED here is my xml file ftpd-typical.xml: <?xml version="1.0" encoding="UTF-8"?>  <server xmlns="http://mina.apache.org/ftpserver/spring/v1" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:beans="http://www.springframework.org/schema/beans" xsi:schemaLocation=" http://mina.apache.org/ftpserver/spring/v1 http://mina.apache.org/ftpserver/ftpserver-1.0.xsd " id="Prometheus"> <listeners> <nio-listener name="default" port="2121" /> </listeners> <db-user-manager encrypt-passwords="salted"> <data-source> <beans:bean class="org.apache.commons.dbcp.BasicDataSource" > <beans:property name="driverClassName" value="com.mysql.jdbc.Driver" /> <beans:property name="url" value="jdbc:mysql://localhost/apache_test" /> <beans:property name="username" value="amy" /> <beans:property name="password" value="piyush" /> </beans:bean> </data-source> <insert-user>INSERT INTO FTP_USER (userid, userpassword, homedirectory, enableflag, writepermission, idletime, uploadrate, downloadrate) VALUES ('{userid}', '{userpassword}', '{homedirectory}', {enableflag}, {writepermission}, {idletime}, {uploadrate}, {downloadrate}) </insert-user> <update-user>UPDATE FTP_USER SET userpassword='{userpassword}',homedirectory='{homedirectory}',enableflag={enableflag},writepermission={writepermission},idletime={idletime},uploadrate={uploadrate},downloadrate={downloadrate} WHERE userid='{userid}' </update-user> <delete-user>DELETE FROM FTP_USER WHERE userid = '{userid}' </delete-user> <select-user>SELECT userid, userpassword, homedirectory, enableflag, writepermission, idletime, uploadrate, downloadrate, maxloginnumber, maxloginperip FROM FTP_USER WHERE userid = '{userid}' </select-user> <select-all-users>SELECT userid FROM FTP_USER ORDER BY userid </select-all-users> <is-admin>SELECT userid FROM FTP_USER WHERE userid='{userid}' AND userid='admin' </is-admin> <authenticate>SELECT userpassword from FTP_USER WHERE userid='{userid}'</authenticate> </db-user-manager> </server>

Read the article
IIS6 Log time recording problems

- by Hafthor

On three separate occasions on two separate servers at nearly the same times, 6.9 hours seemingly went by without any data being written to the IIS logs, but, on closer inspection, it appears that it was all recorded all at once. Here's the facts as I know them: Windows Server 2003 R2 w/ IIS6 Logging using GMT, server local time GMT-7. Application was still operating and I have SQL data to prove that Time gaps appear in log file, not across two # headers appear at gap Load balancer pings every 30 seconds No caching Here's info on a particular case: an entry appears for 2009-09-21 18:09:27 then #headers the next entry is for 2009-09-22 01:21:54, and so are the next 1600 entries in this log file and 370 in the next log file. about half of the ~2000 entries on 2009-09-22 01:21:54 are load balancer pings (est. at 2/min for 6.9hrs = 828 pings) then entries are recorded as normal. I believe that these events may coincide with me deploying an ASP.NET application update into those machines. Here's some relevant content from the logs in question: ex090921.log line 3684 2009-09-21 17:54:40 GET /ping.aspx - 80 404 0 0 3733 122 0 2009-09-21 17:55:11 GET /ping.aspx - 80 404 0 0 3733 122 0 2009-09-21 17:55:42 GET /ping.aspx - 80 404 0 0 3733 122 0 2009-09-21 17:56:13 GET /ping.aspx - 80 404 0 0 3733 122 0 2009-09-21 17:56:45 GET /ping.aspx - 80 404 0 0 3733 122 0 #Software: Microsoft Internet Information Services 6.0 #Version: 1.0 #Date: 2009-09-21 18:04:37 #Fields: date time cs-method cs-uri-stem cs-uri-query s-port sc-status sc-substatus sc-win32-status sc-bytes cs-bytes time-taken 2009-09-22 01:04:06 GET /ping.aspx - 80 404 0 0 3733 122 3078 2009-09-22 01:04:06 GET /ping.aspx - 80 404 0 0 3733 122 109 2009-09-22 01:04:06 GET /ping.aspx - 80 200 0 0 278 122 3828 2009-09-22 01:04:06 GET /ping.aspx - 80 200 0 0 278 122 0 2009-09-22 01:04:06 GET /ping.aspx - 80 200 0 0 278 122 0 ... continues until line 5449 2009-09-22 01:04:06 GET /ping.aspx - 80 200 0 0 277 122 0 <eof> ex090922.log #Software: Microsoft Internet Information Services 6.0 #Version: 1.0 #Date: 2009-09-22 00:00:16 #Fields: date time cs-method cs-uri-stem cs-uri-query s-port sc-status sc-substatus sc-win32-status sc-bytes cs-bytes time-taken 2009-09-22 01:04:06 GET /ping.aspx - 80 200 0 0 277 122 0 2009-09-22 01:04:06 GET /ping.aspx - 80 200 0 0 277 122 0 ... continues until line 367 2009-09-22 01:04:06 GET /ping.aspx - 80 200 0 0 277 122 0 2009-09-22 01:04:30 GET /ping.aspx - 80 200 0 0 277 122 0 ... back to normal behavior Note the seemingly correct date/time written to the #header of the new log file. Also note that /ping.aspx returned 404 then switched to 200 just as the problem started. I rename the "I'm alive page" so the load balancer stops sending requests to the server while I'm working on it. What you see here is me renaming it back so the load balancer will use the server. So, this problem definitely coincides with me re-enabling the server. Any ideas?

Read the article
Lion built-in VPN client times out connecting to Windows 2003 PPTP server

- by beporter

I have a new iMac with OS X 10.7 (Lion) on it that refuses to connect to a PPTP-based VPN server (running Windows 2003 SBS). To shortcut past a lot of questions: There is a Dell workstation running Windows 7 on the same LAN as the Mac that is able to establish a PPTP connection to the same VPN server using the same credentials. That would seem to rule out any possible problems with the server, the port forwards on the server's firewall, the internet connection between the two, and the router local to the Dell and iMac. Here's a "verbose" dump of the PPP log from the iMac: Tue Sep 6 10:13:11 2011 : using link 0 Tue Sep 6 10:13:11 2011 : Using interface ppp0 Tue Sep 6 10:13:11 2011 : Connect: ppp0 socket[34:17] Tue Sep 6 10:13:11 2011 : sent [LCP ConfReq id=0x1 ] Tue Sep 6 10:13:11 2011 : PPTP port-mapping for en0, interfaceIndex: 0, Protocol: None, Private Port: 0, Public Address: 45f6f181, Public Port: 0, TTL: 0. Tue Sep 6 10:13:11 2011 : PPTP port-mapping for en0 inconsistent. is Connected: 1, Previous interface: 4, Current interface 0 Tue Sep 6 10:13:11 2011 : PPTP port-mapping for en0 initialized. is Connected: 1, Previous publicAddress: (0), Current publicAddress 45f6f181 Tue Sep 6 10:13:11 2011 : PPTP port-mapping for en0 fully initialized. Flagging up Tue Sep 6 10:13:14 2011 : sent [LCP ConfReq id=0x1 ] Tue Sep 6 10:13:17 2011 : sent [LCP ConfReq id=0x1 ] Tue Sep 6 10:13:20 2011 : sent [LCP ConfReq id=0x1 ] Tue Sep 6 10:13:23 2011 : sent [LCP ConfReq id=0x1 ] Tue Sep 6 10:13:26 2011 : sent [LCP ConfReq id=0x1 ] Tue Sep 6 10:13:29 2011 : sent [LCP ConfReq id=0x1 ] Tue Sep 6 10:13:32 2011 : sent [LCP ConfReq id=0x1 ] Tue Sep 6 10:13:35 2011 : sent [LCP ConfReq id=0x1 ] Tue Sep 6 10:13:38 2011 : sent [LCP ConfReq id=0x1 ] Tue Sep 6 10:13:41 2011 : LCP: timeout sending Config-Requests Tue Sep 6 10:13:41 2011 : Connection terminated. Tue Sep 6 10:13:41 2011 : PPTP disconnecting... Tue Sep 6 10:13:41 2011 : PPTP clearing port-mapping for en0 Tue Sep 6 10:13:41 2011 : PPTP disconnected The error seems to be focused around the line, LCP: timeout sending Config-Requests, but I haven't had any luck in finding troubleshooting information for this. I've tried completely deleting the entire VPN "connection" from the Network prefpane and recreating it from scratch. I am certain the connection details are correct because they exactly match what successfully connects from the Win7 machine sitting next to the iMac. Any suggestions?

Read the article
Too many Tunnel Adapter Interfaces

- by Tomas Lycken

If I open a command prompt on my machine and type ipconfig /all, I see lots of Tunnel adapter Local Area Connection* 9: Media state . . . . . . . . . . . . . : Media disconnected Connection-specific DNS Sufficx . . . : Description . . . . . . . . . . . . . : Microsoft 6to4 Adapter #5 Physical address. . . . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . . . : No Autoconfiguration Enabled . . . . . . : Yes In fact, they're so many that my "real" adapters are pushed out of the stack, and can't be seen anymore. Is there any flag I can use on ipconfig to hide all virtual interfaces? Or is there some other way around this problem? Since they always say "Media disconnected" I suppose disabling could be an option, but if possible I'd rather not turn any functionality off. I just want to control what output I get from ipconfig. Also, I know these are related to IPv6 stuff. However, most of what I find on google merely states what these are, and that they're harmless - nothing about hiding/removing them.

Read the article
Connecting debian and windows via IPsec VPN with Racoon and ipsec-tools

- by Michi Qne

I've some trouble with the IPsec configuration on my debian server (6 squeeze). This server should connect via IPsec VPN to an windows server, which is protected by an firewall. I've used racoon and ipsec-tools and this tutorial http://wiki.debian.org/IPsec. However, I am not quite sure, if this tutorial fits to my purpose, because of some differences: my Host and my gateway are the same server. So I don't have two different ip addresses. I guess, that's not a problem the other server is an windows system behind a firewall. Hopefully, not a problem the subnet of the windows system is /32 not /24. So I change it to /32. I worked through the tutorial step by step, but I wasn't able to route the ip. The following command didn't work for me: ip route add to 172.16.128.100/32 via XXX.XXX.XXX.XXX src XXX.XXX.XXX.XXX So I tried the following instead: ip route add to 172.16.128.100 .., which obviously not solved the problem. The next problem is the compression. The windows doesn't use a compression, but 'compression_algorithm none;' doesn't work with my racoon. So the current value is 'compression_algorithm deflate;' So my current result looks like this: When I am trying to ping the windows host (ping 172.16.128.100), I receive the following error message from ping: ping: sendmsg: Operation not permitted And racoon logs: racoon: ERROR: failed to get sainfo. After googling for a while I came to no conclusion, what's the solution. Does this error message mean that the first phase of IPsec works? I am thankful for any advice. I guess my configs might be helpful. My racoon.conf looks like this: path pre_shared_key "/etc/racoon/psk.txt"; remote YYY.YYY.YYY.YYY { exchange_mode main; proposal { lifetime time 8 hour; encryption_algorithm 3des; hash_algorithm sha1; authentication_method pre_shared_key; dh_group 2; } } sainfo address XXX.XXX.XXX.XXX/32 any address 172.16.128.100/32 any { pfs_group 2; lifetime time 8 hour; encryption_algorithm aes 256; authentication_algorithm hmac_sha1; compression_algorithm deflate; } And my ipsec-tools.conf looks like this: flush; spdflush; spdadd XXX.XXX.XXX.XXX/32 172.16.128.100/32 any -P out ipsec esp/tunnel/XXX.XXX.XXX.XXX-YYY.YYY.YYY.YYY/require; spdadd 172.16.128.100/32 XXX.XXX.XXX.XXX/32 any -P in ipsec esp/tunnel/YYY.YYY.YYY.YYY-XXX.XXX.XXX.XXX/require; If anyone has an advice, that would be awesome. Thanks in Advance. Greets, Michael It was a simple copy-and-paste error in an ip address.

Read the article
NetBackup with VSS and Instant Recovery - Failing to delete old snapshots

- by Jonathan Bourke

We are attempting to implement Microsoft VSS for snap-shotting in our NetBackup 6.5.3.1 environment. The clients are both 32 & 64 bit Windows 2003 Server. Snapshot parameters are: Instant recovery is enabled Maximum snapshots = 1 Provider type = 1 (System) Snapshot attribute = 1 (Differential) All backups successfully complete, and VSS shadows are successfully created both for the snapshot backup and for the open files (shadow copy components). The Issue: NetBackup is not clearing or overwriting old snapshots with each successive backup. When we list shadows, and shadow storage, it is increasing and increasing. IT is not honouring the Maximum Snapshot setting. The Logs: The bpfis log doesn’t really appear to show any errors other than for methods which we are not employing (VxVM, Flashsnap, etc.). A section is as follows: 11:54:10.744 [348.4724] <2> logparams: D:\Program Files\Veritas\NetBackup\bin\bpfis.exe delete -nbu -id htpststr001.san.mgmt.det_1248918143 -bpstart_to 300 -bpend_to 300 -clnt htpststr001.san.mgmt.det 11:54:10.744 [348.4724] <4> bpfis: INF - BACKUP START 348 11:54:11.713 [348.4724] <8> onlfi_initialize_vfms: VfMS error 10; see following messages: 11:54:11.713 [348.4724] <8> onlfi_initialize_vfms: Non-fatal method error was reported 11:54:11.713 [348.4724] <8> onlfi_initialize_vfms: vfm_configure_fi_one: method: FlashSnap, type: FIM, function: FlashSnap_init 11:54:11.713 [348.4724] <8> onlfi_initialize_vfms: VfMS method error 3; see following message: 11:54:11.713 [348.4724] <8> onlfi_initialize_vfms: FlashSnap_init: Veritas Volume Manager not installed. 11:54:11.713 [348.4724] <8> onlfi_initialize_vfms: VfMS error 10; see following messages: 11:54:11.713 [348.4724] <8> onlfi_initialize_vfms: Non-fatal method error was reported 11:54:11.713 [348.4724] <8> onlfi_initialize_vfms: vfm_configure_fi_one: method: vxvm, type: FIM, function: vxvm_init 11:54:11.713 [348.4724] <8> onlfi_initialize_vfms: VfMS method error 3; see following message: 11:54:11.713 [348.4724] <8> onlfi_initialize_vfms: vxvm_init: Veritas Volume Manager not installed. 11:54:11.713 [348.4724] <4> onlfi_thaw: Thawing C:\ using snapshot method VSS. 11:54:11.713 [348.4724] <2> onlfi_vfms_logf: vfm_thaw: delete snapshot ... 11:54:11.744 [348.4724] <2> onlfi_vfms_logf: snapshot services: emcclariionfi:Thu Jul 30 2009 11:54:11.744000 <Thread id - 4724> Unable to import any login credentials for any appliances. 11:54:11.760 [348.4724] <2> onlfi_vfms_logf: snapshot services: hpevafi:Thu Jul 30 2009 11:54:11.760000 <Thread id - 4724> CHpEvaPlugin::init: CLI tool is not installed. 11:54:11.760 [348.4724] <2> onlfi_vfms_logf: snapshot services: hpmsafi:Thu Jul 30 2009 11:54:11.760000 <Thread id - 4724> No array mangement credentials are available in configuration file. 11:54:13.806 [348.4724] <4> onlfi_thaw: do_thaw return value: 0 11:54:13.806 [348.4724] <4> onlfi_thaw: Thawing D:\ using snapshot method VSS. 11:54:15.806 [348.4724] <4> onlfi_thaw: do_thaw return value: 0 11:54:19.806 [348.4724] <2> fis_delete_id: removing D:\Program Files\Veritas\NetBackup\online_util\fi_cntl\bpfis.fim.htpststr001.san.mgmt.det_1248918143.0 11:54:19.806 [348.4724] <2> fis_delete_id: removing D:\Program Files\Veritas\NetBackup\online_util\fi_cntl\bpfis.fim.htpststr001.san.mgmt.det_1248918143.0.fiid 11:54:19.853 [348.4724] <4> bpfis: INF - EXIT STATUS 0: the requested operation was successfully completed The Question: Has anyone any experience of NetBackup / VSS not clearing snapshots after backups? We will ultimately be using a HP EVA for the snapshots, but we want to ensure correct functioning at a VSS level before we go further. Regards, Jonathan (PS: Question previously posted by my colleague on entsupport.symantec.com)

Read the article
networking through openstack installed on vm

- by Mandar Katdare

I am trying to set up a test installation of Openstack on a Ubuntu 12.04 VM running on a ESXi server. So far I have been able to launch the VMs on the ESXi, however am unable to assign IP addresses to them. As the VM with the Openstack installation has a single public IP, I wish to assign IPs to the VMs create through Openstack so that they can directly interact with the public network itself without having a separate private network. So I feel that bridging would not be the correct option here. But am unable to find the correct documents to go ahead with such an install. My ifconfig looks as follows: eth0 Link encap:Ethernet HWaddr 00:0c:29:6f:8a:d7 inet addr:192.168.4.167 Bcast:192.168.4.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe6f:8ad7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:391640 errors:33 dropped:98 overruns:0 frame:0 TX packets:545044 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:40303931 (40.3 MB) TX bytes:763127348 (763.1 MB) Interrupt:18 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:146127 errors:0 dropped:0 overruns:0 frame:0 TX packets:146127 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:799815763 (799.8 MB) TX bytes:799815763 (799.8 MB) virbr0 Link encap:Ethernet HWaddr 8a:80:33:32:63:a0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) The eth0 is the adapter that I intend to use for all communication. My nova.conf looks as follows: --dhcpbridge_flagfile=/etc/nova/nova.conf --dhcpbridge=/usr/bin/nova-dhcpbridge --logdir=/var/log/nova --state_path=/var/lib/nova --lock_path=/var/lock/nova --allow_admin_api=true --use_deprecated_auth=false --auth_strategy=keystone --scheduler_driver=nova.scheduler.simple.SimpleScheduler --s3_host=192.168.4.167 --ec2_host=192.168.4.167 --rabbit_host=192.168.4.167 --cc_host=192.168.4.167 --nova_url=http://192.168.4.167:8774/v1.1/ --routing_source_ip=192.168.4.167 --glance_api_servers=192.168.4.167:9292 --image_service=nova.image.glance.GlanceImageService --iscsi_ip_prefix=192.168.4 --sql_connection=mysql://novadbadmin:[email protected]/nova --ec2_url=http://192.168.4.167:8773/services/Cloud --keystone_ec2_url=http://192.168.4.167:5000/v2.0/ec2tokens --api_paste_config=/etc/nova/api-paste.ini --libvirt_type=kvm --libvirt_use_virtio_for_bridges=true --start_guests_on_host_boot=true --resume_guests_state_on_host_boot=true --vnc_enabled=true --vncproxy_url=http://192.168.4.167:6080 --vnc_console_proxy_url=http://192.168.4.167:6080 # network specific settings --network_manager=nova.network.manager.FlatDHCPManager --public_interface=eth0 --vmwareapi_host_ip=192.168.4.254 --vmwareapi_host_username=**** --vmwareapi_host_password=**** --vmwareapi_wsdl_loc=http://127.0.0.1:8080/wsdl/vim25/vimService.wsdl --fixed_range=192.168.4.190/24 --floating_range=192.168.4.190/24 --network_size=32 --flat_network_dhcp_start=192.168.4.190 --flat_injected=False --force_dhcp_release --iscsi_helper=tgtadm --connection_type=vmwareapi --root_helper=sudo nova-rootwrap --verbose --libvirt_use_virtio_for_bridges --ec2_private_dns_show --novnc_enabled=true --novncproxy_base_url=http://192.168.4.167:6080/vnc_auto.html --vncserver_proxyclient_address=192.168.4.167 --vncserver_listen=192.168.4.167 192.168.4.167 is my VM with the Openstack installation and 192.168.4.254 is my ESXi server on which the VM runs. Can anyone advice me about how to proceed? Thanks, Mandar

Read the article
dovecot imap ssl certificate issues

- by mulllhausen

i have been trying to configure my dovecot imap server (version 1.0.10 - upgrading is not an option at this stage) with a new ssl certificate on ubuntu like so: $ grep ^ssl /etc/dovecot/dovecot.conf ssl_disable = no ssl_cert_file = /etc/ssl/certs/mydomain.com.crt.20120904 ssl_key_file = /etc/ssl/private/mydomain.com.key.20120904 $ /etc/init.t/dovecot stop $ sudo dovecot -p $ [i enter the ssl password here] it doesn't show any errors and when i run ps aux | grep dovecot i get root 21368 0.0 0.0 12452 688 ? Ss 15:19 0:00 dovecot -p root 21369 0.0 0.0 71772 2940 ? S 15:19 0:00 dovecot-auth dovecot 21370 0.0 0.0 14140 1904 ? S 15:19 0:00 pop3-login dovecot 21371 0.0 0.0 14140 1900 ? S 15:19 0:00 pop3-login dovecot 21372 0.0 0.0 14140 1904 ? S 15:19 0:00 pop3-login dovecot 21381 0.0 0.0 14280 2140 ? S 15:19 0:00 imap-login dovecot 21497 0.0 0.0 14280 2116 ? S 15:29 0:00 imap-login dovecot 21791 0.0 0.0 14148 1908 ? S 15:48 0:00 imap-login dovecot 21835 0.0 0.0 14148 1908 ? S 15:53 0:00 imap-login dovecot 21931 0.0 0.0 14148 1904 ? S 16:00 0:00 imap-login me 21953 0.0 0.0 5168 944 pts/0 S+ 16:02 0:00 grep --color=auto dovecot which looks like it is all running fine. so then i test to see if i can telnet to the dovecot server, and this works fine: $ telnet localhost 143 Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. * OK Dovecot ready. but when i test whether dovecot has configured the ssl certificates properly, it appears to fail: $ sudo openssl s_client -connect localhost:143 -starttls imap CONNECTED(00000003) depth=0 /description=xxxxxxxxxxxxxxxxx/C=AU/ST=xxxxxxxx/L=xxxx/O=xxxxxx/CN=*.mydomain.com/[email protected] verify error:num=20:unable to get local issuer certificate verify return:1 depth=0 /description=xxxxxxxxxxx/C=AU/ST=xxxxxx/L=xxxx/O=xxxx/CN=*.mydomain.com/[email protected] verify error:num=27:certificate not trusted verify return:1 depth=0 /description=xxxxxxxx/C=AU/ST=xxxxxxxxxx/L=xxxx/O=xxxxx/CN=*.mydomain.com/[email protected] verify error:num=21:unable to verify the first certificate verify return:1 --- Certificate chain 0 s:/description=xxxxxxxxxxxx/C=AU/ST=xxxxxxxxxx/L=xxxxxxxx/O=xxxxxxx/CN=*.mydomain.com/[email protected] i:/C=IL/O=StartCom Ltd./OU=Secure Digital Certificate Signing/CN=StartCom Class 2 Primary Intermediate Server CA --- Server certificate -----BEGIN CERTIFICATE----- xxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx . . . xxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxx== -----END CERTIFICATE----- subject=/description=xxxxxxxxxx/C=AU/ST=xxxxxxxxx/L=xxxxxxx/O=xxxxxx/CN=*.mydomain.com/[email protected] issuer=/C=IL/O=StartCom Ltd./OU=Secure Digital Certificate Signing/CN=StartCom Class 2 Primary Intermediate Server CA --- No client certificate CA names sent --- SSL handshake has read 2831 bytes and written 342 bytes --- New, TLSv1/SSLv3, Cipher is DHE-RSA-AES256-SHA Server public key is 2048 bit Compression: NONE Expansion: NONE SSL-Session: Protocol : TLSv1 Cipher : DHE-RSA-AES256-SHA Session-ID: xxxxxxxxxxxxxxxxxxxx Session-ID-ctx: Master-Key: xxxxxxxxxxxxxxxxxx Key-Arg : None Start Time: 1351661960 Timeout : 300 (sec) Verify return code: 21 (unable to verify the first certificate) --- . OK Capability completed. at least, i'm assuming this is a failure???

Read the article
Failed MDADM Array With Ext.4 Partition - "e2fsck: unable to set superblock flags on /dev/md0"

- by Matthew Hodgkins

Had a power failure and now my mdadm array is having problems. sudo mdadm -D /dev/md0 [hodge@hodge-fs ~]$ sudo mdadm -D /dev/md0 /dev/md0: Version : 0.90 Creation Time : Sun Apr 25 01:39:25 2010 Raid Level : raid5 Array Size : 8790815232 (8383.57 GiB 9001.79 GB) Used Dev Size : 1465135872 (1397.26 GiB 1500.30 GB) Raid Devices : 7 Total Devices : 7 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Sat Aug 7 19:10:28 2010 State : clean, degraded, recovering Active Devices : 6 Working Devices : 7 Failed Devices : 0 Spare Devices : 1 Layout : left-symmetric Chunk Size : 128K Rebuild Status : 10% complete UUID : 44a8f730:b9bea6ea:3a28392c:12b22235 (local to host hodge-fs) Events : 0.1307608 Number Major Minor RaidDevice State 0 8 81 0 active sync /dev/sdf1 1 8 97 1 active sync /dev/sdg1 2 8 113 2 active sync /dev/sdh1 3 8 65 3 active sync /dev/sde1 4 8 49 4 active sync /dev/sdd1 7 8 33 5 spare rebuilding /dev/sdc1 6 8 16 6 active sync /dev/sdb sudo mount -a [hodge@hodge-fs ~]$ sudo mount -a mount: wrong fs type, bad option, bad superblock on /dev/md0, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so sudo fsck.ext4 /dev/md0 [hodge@hodge-fs ~]$ sudo fsck.ext4 /dev/md0 e2fsck 1.41.12 (17-May-2010) fsck.ext4: Group descriptors look bad... trying backup blocks... /dev/md0: recovering journal fsck.ext4: unable to set superblock flags on /dev/md0 sudo dumpe2fs /dev/md0 | grep -i superblock [hodge@hodge-fs ~]$ sudo dumpe2fs /dev/md0 | grep -i superblock dumpe2fs 1.41.12 (17-May-2010) Primary superblock at 0, Group descriptors at 1-524 Backup superblock at 32768, Group descriptors at 32769-33292 Backup superblock at 98304, Group descriptors at 98305-98828 Backup superblock at 163840, Group descriptors at 163841-164364 Backup superblock at 229376, Group descriptors at 229377-229900 Backup superblock at 294912, Group descriptors at 294913-295436 Backup superblock at 819200, Group descriptors at 819201-819724 Backup superblock at 884736, Group descriptors at 884737-885260 Backup superblock at 1605632, Group descriptors at 1605633-1606156 Backup superblock at 2654208, Group descriptors at 2654209-2654732 Backup superblock at 4096000, Group descriptors at 4096001-4096524 Backup superblock at 7962624, Group descriptors at 7962625-7963148 Backup superblock at 11239424, Group descriptors at 11239425-11239948 Backup superblock at 20480000, Group descriptors at 20480001-20480524 Backup superblock at 23887872, Group descriptors at 23887873-23888396 Backup superblock at 71663616, Group descriptors at 71663617-71664140 Backup superblock at 78675968, Group descriptors at 78675969-78676492 Backup superblock at 102400000, Group descriptors at 102400001-102400524 Backup superblock at 214990848, Group descriptors at 214990849-214991372 Backup superblock at 512000000, Group descriptors at 512000001-512000524 Backup superblock at 550731776, Group descriptors at 550731777-550732300 Backup superblock at 644972544, Group descriptors at 644972545-644973068 Backup superblock at 1934917632, Group descriptors at 1934917633-1934918156 sudo e2fsck -b 32768 /dev/md0 [hodge@hodge-fs ~]$ sudo e2fsck -b 32768 /dev/md0 e2fsck 1.41.12 (17-May-2010) /dev/md0: recovering journal e2fsck: unable to set superblock flags on /dev/md0 sudo dmesg | tail [hodge@hodge-fs ~]$ sudo dmesg | tail EXT4-fs (md0): ext4_check_descriptors: Checksum for group 0 failed (59837!=29115) EXT4-fs (md0): group descriptors corrupted! EXT4-fs (md0): ext4_check_descriptors: Checksum for group 0 failed (59837!=29115) EXT4-fs (md0): group descriptors corrupted! Please Help!!!

Read the article
eth0:0 is configured but not listed in ifconfig output

- by FractalizeR

Hello. I have the following problem: My server was given two IPs from [b]different[/b] subnets. Now I am trying to configure the system to work properly. I have created [root@server ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0 # Intel Corporation 80003ES2LAN Gigabit Ethernet Controller (Copper) HWADDR=00:30:48:DA:B1:0E DEVICE=eth0 BOOTPROTO=none BROADCAST=79.174.69.255 IPADDR=79.174.69.241 NETMASK=255.255.254.0 NETWORK=79.174.68.0 ONBOOT=yes GATEWAY=79.174.68.1 TYPE=Ethernet [root@server ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0:0 # Intel Corporation 80003ES2LAN Gigabit Ethernet Controller (Copper) HWADDR=00:30:48:DA:B1:0E DEVICE=eth0 BOOTPROTO=none BROADCAST=79.174.69.255 IPADDR=79.174.71.74 NETMASK=255.255.255.0 NETWORK=79.174.71.1 ONBOOT=yes GATEWAY=79.174.71.1 TYPE=Ethernet But both after "service network restart" and after "reboot" [root@server ~]# ifconfig eth0 Link encap:Ethernet HWaddr 00:30:48:DA:B1:0E inet addr:79.174.71.74 Bcast:79.174.71.255 Mask:255.255.255.0 inet6 addr: fe80::230:48ff:feda:b10e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:910284 errors:0 dropped:0 overruns:0 frame:0 TX packets:2924 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:257964879 (246.0 MiB) TX bytes:232450 (227.0 KiB) Memory:df220000-df240000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27 errors:0 dropped:0 overruns:0 frame:0 TX packets:27 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6976 (6.8 KiB) TX bytes:6976 (6.8 KiB) Device eth0:0 is not shown as active. If I try [root@server ~]# ifconfig eth0:0 eth0:0 Link encap:Ethernet HWaddr 00:30:48:DA:B1:0E UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:df220000-df240000 It is shown as up and running, but IP is not assigned to it. Also it is strange, that IP address assigned to eth0:0 in config file is used by eth0. /var/log/messages shows nothing about network configuration errors on either eth0 or eth0:0. system-config-network seem to understand all settings correctly and resaves them ok also. "ifup eth0:0" executes ok, but ifconfig afterwards shows no eth0:0 device after that. What did I do wrong? May be the problem is that IPs are from different subnets?

Read the article
cf3 Can't stat ... in files.copyfrom promise

- by Xerxes

On the client: # cf-agent -KIv ... cf3 -> Handling file existence constraints on /etc/cfengine3 cf3 -> Copy file /etc/cfengine3 from /srv/cfengine/sysconf/server/inputs check cf3 No existing connection to 172.31.69.83 is established... cf3 Set cfengine port number to 5308 = 5308 cf3 -> Connect to 172.31.69.83 = 172.31.69.83 on port 5308 cf3 LastSaw host 172.31.69.83 now cf3 Loaded /var/lib/cfengine3/ppkeys/root-172.31.69.83.pub cf3 .....................[.h.a.i.l.]................................. cf3 Strong authentication of server=172.31.69.83 connection confirmed cf3 Server returned error: Unspecified server refusal (see verbose server output) cf3 Can't stat /srv/cfengine/sysconf/server/inputs in files.copyfrom promise cf3 ?> defining promise result class Cfengine_Inputs_Updated_Failed .... cf3 ......................................................... cf3 Promise handle: cf3 Promise made by: [cf-agent.cf ] FAILED 172.31.69.83:///srv/cfengine/sysconf/server/inputs -> localhost:///etc/cfengine3 However, on the server (172.31.69.83), there's no reason why it can't stat the directory: cyrus:/srv/cfengine/sysconf/server# ls -l /srv/cfengine/sysconf/server/inputs total 52 -rw-r--r-- 1 root root 2142 Sep 6 21:54 cf-agent.cf -rw-r--r-- 1 root root 831 Sep 6 18:31 cf-execd.cf -rw-r--r-- 1 root root 4517 Sep 6 21:44 cf-serverd.cf -rw-r--r-- 1 root root 3082 Sep 6 21:44 dns.cf -rw-r--r-- 1 root root 2028 Sep 6 15:12 failsafe.cf -rw-r--r-- 1 root root 5966 Sep 6 21:44 ldap-masters.cf -rw-r--r-- 1 root root 4380 Sep 6 18:31 ldap-security.cf -rw-r--r-- 1 root root 2735 Sep 6 08:21 lib-core.cf -rw-r--r-- 1 root root 1506 Sep 6 21:45 lib-utils.cf -rw-r--r-- 1 root root 2635 Sep 6 20:27 lib-vars.cf -rw-r--r-- 1 root root 2057 Sep 3 17:46 nss.cf -rw-r--r-- 1 root root 1472 Sep 6 18:31 packages.cf -rw-r--r-- 1 root root 1257 Sep 6 18:01 pam-security.cf -rw-r--r-- 1 root root 4019 Sep 6 19:32 promises.cf -rw-r--r-- 1 root root 2808 Sep 3 17:22 site.cf -rw-r--r-- 1 root root 1670 Sep 6 18:31 sudo-security.cf -rw-r--r-- 1 root root 831 Sep 6 18:31 sys-security.cf -rw-r--r-- 1 root root 890 Sep 6 18:31 sys-users.cf cyrus:/srv/cfengine/sysconf/server# I don't see anything interesting server side either when running: /usr/sbin/cf-serverd -d4 --verbose --no-fork And the following does not have any complaints: /usr/sbin/cf-promises -v Any ideas? I'm running cfengine3 on debian, v3.0.5+dfsg-1 - and the cf-agent.cf file is as follows: bundle agent Update { files: linux:: "${cf3.path[inputs]}" action => immediate, move_obstructions => "true", depth_search => Recursive, copy_from => MirrorFrom( "${cf3.host[server]}", "${cf3.path[scm-inputs]}", "true", "0400" ), classes => DefineSoftClass("Cfengine_Inputs_Updated") ; "${cf3.path[sbin]}" comment => "Setting cf3 client sbin scripts: ${cf3.path[sbin]}/", action => immediate, depth_search => Recursive, copy_from => MirrorFrom( "${cf3.host[server]}", "${cf3.path[scm-cnt-scripts]}", "false", "0555" ) ; reports: Cfengine_Inputs_Updated:: "[cf-agent.cf ] Services:CFAgent:Inputs:Updated"; Cfengine_Inputs_Updated_Failed:: "[cf-agent.cf ] FAILED ${cf3.host[server]}://${cf3.path[scm-inputs]} -> localhost://${cf3.path[inputs]}"; } I lie, there is something interesting with a little more debugging... AccessControl(/srv/cfengine/sysconf/server/inputs) AccessControl, match(/srv/cfengine/sysconf/server/inputs,client.com.au) encrypt request=1 Examining rule in access list (/srv/cfengine/sysconf/server/inputs,/home/cfengine)? cf3 Host client.com.au denied access to /srv/cfengine/sysconf/server/inputs Unappending Host client.com.au denied access to /srv/cfengine/sysconf/server/inputs cf3 Access control in sync Unappending Access control in sync Transaction Send[t 59][Packed text] Attempting to send 67 bytes SendSocketStream, sent 67 cf3 From (host=client.com.au,user=root,ip=172.31.69.3) Unappending From (host=client.com.au,user=root,ip=172.31.69.3) cf3 REFUSAL of request from connecting host: (SYNCH 1283777156 STAT /srv/cfengine/sysconf/server/inputs) Unappending REFUSAL of request from connecting host: (SYNCH 1283777156 STAT /srv/cfengine/sysconf/server/inputs) RecvSocketStream(8) cf3 -> Accepting a connection I'll keep looking.

Read the article
How to set up a mini call center?

- by Ralph

I'm trying to figure out how to set up a miniature call center for a small business. Like, for 1-4 people to take calls, but hopefully expandable to more. We want to accept nation-wide calls, and then I guess distribute the calls among the available agents. If no one is available, I guess it should either put them in a queue and play some annoying music for them, or forward to call to an agent who has least-recently taken a call who can then quickly answer and say "please hold" until they're done their call. We want to have one phone number that customers can call. I guess we then need some kind of ACD system which would take each call and forward it to an agent based on some algorithm? Then we would need to purchase a separate phone line for each agent, plus one just for the distributor? Or do we need several "extra" lines to maintain a queue (one for each customer waiting too)? This "ACD" thing, is it just a device that you would plug a phone line into (or several?), and maybe connect to a computer, aided by some software? Or is a subscription thing that I would need from my local telephone provider? Next, the business we're running, the callers will be repeat customers. It would be helpful to automatically pull up their profile based on the incoming number. The "software" our agents will be running will just be a website where they can log in (preferably from home) and then enter some information they would obtain through the call. So, the system would have to somehow interface with the website if possible. If not, we'll just have to ask each customer for an identifier (phone number, username, customer number, or something). Is this possible? I guess each computer would need a device that the call would pass through, and then if I can somehow hook into that, then I can write some software that will interface with the site. So, where do I start? What hardware do we need to buy? What subscriptions do we need? We were thinking this magicJack might help us in accepting long-distance calls for cheaper, but my understanding is that they provide you with some weird-looking number, is there a way we could "mask" it with our toll-free number? And then pass the incoming calls through the distributor system, which would then get passed to the call-accepting device which would both allow an agent to answer the call and have a software hook? (I realize this might be partially out of the scope of SU, but I wasn't sure where else to ask. It is about computer(-aided) hardware and software anyway.) P.S.: I don't need any of that "press 1 to talk to..." or "say xyz to..." junk. Just a straight-forward, connect-to-next-available-agent system.

Read the article
shell script over SSH ends unexpectedly after running 'ant build'

- by YShin

I wrote a shell script that runs on remote host to build source code with 'ant build' command, and then distribute the built binary to other servers. However, right after Ant build is over successfully(I can see the command line output saying Build was successful), the ssh session ends and whatever commands after 'ant build' does not get executed. I'm confused what might be cause of this behavior. I suspected that it might be because the 'ant build' command takes too long time, and SSH somehow quits itself after that long command. But I don't think that's correct since if I just do 'sleep 60' in place of 'ant build' command, it actually execute latter commands as intended. I'm new at shell programming, so I might have made some silly misassumption. Can someone provide a pointer to a possible cause of this problem? My shell script #!/bin/bash # Inject some variables ssh -T $SSH_USER@$SSH_URL "setenv REMOTE_BASE_DIR $REMOTE_BASE_DIR; setenv CASSANDRA_SRC_TAR_FILE $CASSANDRA_SRC_TAR_FILE; setenv CASSANDRA_SRC_DIR_NAME $CASSANDRA_SRC_DIR_NAME; setenv CLUSTER_SIZE $CLUSTER_SIZE; setenv REMOTE_REDEPLOY_SCRIPT $REMOTE_REDEPLOY_SCRIPT; /bin/bash" << 'EOF' export JAVA_HOME=/usr/lib/jvm/jdk1.7.0 cd $REMOTE_BASE_DIR/$CASSANDRA_SRC_DIR_NAME echo "## Building Cassandra source" ant clean build # Anything after this doesn't run echo "## Ant Build is over. Invoking redeploy script on remote nodes" # Invoke redeploy script for each node for (( i=0; i < CLUSTER_SIZE; i++)) do echo "## Invoking redeploy script on node-$i" done Command-line output ## Building Cassandra source Buildfile: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build.xml clean: [delete] Deleting directory /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build/test [delete] Deleting directory /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build/classes [delete] Deleting directory /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/src/gen-java [delete] Deleting directory /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/src/resources/org/apache/cassandra/config init: [mkdir] Created dir: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build/classes/main [mkdir] Created dir: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build/classes/thrift [mkdir] Created dir: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build/test/lib [mkdir] Created dir: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build/test/classes [mkdir] Created dir: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/src/gen-java maven-ant-tasks-localrepo: maven-ant-tasks-download: maven-ant-tasks-init: maven-declare-dependencies: maven-ant-tasks-retrieve-build: init-dependencies: [echo] Loading dependency paths from file: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build/build-dependencies.xml check-gen-cli-grammar: gen-cli-grammar: [echo] Building Grammar /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/src/java/org/apache/cassandra/cli/Cli.g .... check-gen-cql2-grammar: gen-cql2-grammar: [echo] Building Grammar /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/src/java/org/apache/cassandra/cql/Cql.g ... check-gen-cql3-grammar: gen-cql3-grammar: [echo] Building Grammar /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/src/java/org/apache/cassandra/cql3/Cql.g ... build-project: [echo] apache-cassandra: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build.xml [javac] Compiling 43 source files to /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build/classes/thrift [javac] Note: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/interface/thrift/gen-java/org/apache/cassandra/thrift/Cassandra.java uses or overrides a deprecated API. [javac] Note: Recompile with -Xlint:deprecation for details. [javac] Note: Some input files use unchecked or unsafe operations. [javac] Note: Recompile with -Xlint:unchecked for details. [javac] Compiling 865 source files to /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build/classes/main [javac] Note: Some input files use or override a deprecated API. [javac] Note: Recompile with -Xlint:deprecation for details. [javac] Note: Some input files use unchecked or unsafe operations. [javac] Note: Recompile with -Xlint:unchecked for details. createVersionPropFile: [mkdir] Created dir: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/src/resources/org/apache/cassandra/config [propertyfile] Creating new property file: /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/src/resources/org/apache/cassandra/config/version.properties [copy] Copying 3 files to /scratch/ISS/shin14/repos/apache-cassandra-2.0.8-src-0713/build/classes/main build: BUILD SUCCESSFUL Total time: 32 seconds

Read the article
svn 503 error when commit new files

- by philipp

I am struggling with a strange error when I try to commit my repository. I have a V-server with webmin installed on it. Via Webmin I installed an svn module, created repositories and everything worked fine until three days ago. Trying to commit brings the following error: Commit failed (details follow): Server sent unexpected return value (503 Service unavailable) in response to PROPFIND request for '/svn/rle/!svn/wrk/a1f963a7-0a33-fa48-bfde-183ea06ab958/RLE/.htaccess' Server sent unexpected return value (503 Service unavailable) in response to PROPFIND request for '/svn/rle/RLE/.htaccess' I google everywhere and found only very few solutions. One indicated that a wrong error document is set, another one dealt about the problem that filenames might cause this error and last but not least a wrong proxy configuration in the local svn config could be the reason. After trying all of the solutions suggested I could not reach anything. Only after a server reboot there was a little difference in the error-message, telling me that the server was not able to move a temp file, because the operation was permitted. So I also controlled the permissions of the svn directory, but also with no success. An svn update than restored the "normal" error from above and nothing changed since then. The only change I made on the server, I guess that this could be the reason why svn does not work anymore, was to install the php5_mysql module for apache via apt-get install php5_mysql. Atg the moment I have totally no idea where I could search. I don't know if the problem is on my server or in my repository and I would be glad to get any hint to solve this. Thanks in advance Greetings philipp error log: [Tue Oct 25 19:23:02 2011] [error] [client 217.50.254.18] Could not create activity /svn/rle/!svn/act/d8dd436f-d014-f047-8e87-01baac46a593. [500, #0] Tue Oct 25 19:23:02 2011] [error] [client 217.50.254.18] could not begin a transaction [500, #1] [Tue Oct 25 19:24:21 2011] [error] [client 217.50.254.18] Could not create activity /svn/rle/!svn/act/adac52c2-6f46-f540-b218-2f2ff03b51a4. [500, #0] http.conf: <Location /svn> DAV svn SVNParentPath /home/xxx/svn AuthType Basic AuthName xxx.de AuthUserFile /home/xxx/etc/svn.basic.passwd Require valid-user AuthzSVNAccessFile /home/xxx/etc/svn-access.conf Satisfy Any ErrorDocument 404 default RewriteEngine off </Location> The permissions for the repository directory are : rwxrwxrwx (0777). the directory /svn/rle/!svn/act/adac52c2-6f46-f540-b218-2f2ff03b51a4 does not exist on the server. I think this is part of the repository. So, I just just want to admit that i tried to reach the repository via Browser and i worked, I could see everything, so the error only occurs when I try to commit new files. I also created a second repository and tried to commit files in there, what gave me the same error.

Read the article
CYGWin and sshd. Accepts authentication, but won't connect

- by timramich

Everything I find relating to this is the "ssh-exchange-identification:" error. This doesn't happen for me. I get two lines: Connection to localhost closed by remote host. Connection to localhost closed. ssh -v localhost spits out: OpenSSH_5.8p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug1: Connecting to localhost [::1] port 22. debug1: Connection established. debug1: identity file /home/tim/.ssh/id_rsa type -1 debug1: identity file /home/tim/.ssh/id_rsa-cert type -1 debug1: identity file /home/tim/.ssh/id_dsa type -1 debug1: identity file /home/tim/.ssh/id_dsa-cert type -1 debug1: identity file /home/tim/.ssh/id_ecdsa type -1 debug1: identity file /home/tim/.ssh/id_ecdsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.8 debug1: match: OpenSSH_5.8 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.8 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: sending SSH2_MSG_KEX_ECDH_INIT debug1: expecting SSH2_MSG_KEX_ECDH_REPLY debug1: Server host key: ECDSA 64:e3:27:90:ef:48:93:21:38:ea:9b:0e:0b:07:b0:2a debug1: Host 'localhost' is known and matches the ECDSA host key. debug1: Found key in /home/tim/.ssh/known_hosts:1 debug1: ssh_ecdsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: publickey debug1: Trying private key: /home/tim/.ssh/id_rsa debug1: Trying private key: /home/tim/.ssh/id_dsa debug1: Trying private key: /home/tim/.ssh/id_ecdsa debug1: Next authentication method: keyboard-interactive debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: password tim@localhost's password: debug1: Authentication succeeded (password). Authenticated to localhost ([::1]:22). debug1: channel 0: new [client-session] debug1: Requesting [email protected] debug1: Entering interactive session. debug1: channel 0: free: client-session, nchannels 1 Connection to localhost closed by remote host. Connection to localhost closed. Transferred: sent 2008, received 1376 bytes, in 0.0 seconds Bytes per second: sent 64774.0, received 44387.0 debug1: Exit status -1 I'm really at wit's end here because I couldn't get Windows' remote shell to even work. I'm so sick of using VNC just to get to a shell. Plus Windows' shell sucks because there is nothing like screen. Thanks

Read the article

Search Results

Search found 27428 results on 1098 pages for 'copy local'.

Page 1014/1098 | < Previous Page | 1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 | Next Page >

- by michaelc

- by Patrick J Collins

- by Mickel

- by No1_Melman

- by Recc

- by Ninefingers

- by PartySoft

- by Volune

- by user3719091

- by Mehrdad

- by piyush

- by Hafthor

- by beporter

- by Tomas Lycken

- by Michi Qne

- by Jonathan Bourke

- by Mandar Katdare

- by mulllhausen

- by Matthew Hodgkins

- by FractalizeR

- by Xerxes

- by Ralph

- by YShin

- by philipp

- by timramich

< Previous Page | 1010 1011 1012 1013 1014 1015 1016 1017 1018 1019 1020 1021 | Next Page >