Search Results

Search found 12925 results on 517 pages for 'email routing'.

Page 103/517 | < Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >

• why do Vagrant docs suggest using public IP address 33.33.33.10 for local VMs?

  - by Gert

  I'm following a tutorial to set up vagrant (a tool to build and configure portable virtual machine images), and it seems that vagrant documentation suggests using IPv4 address 33.33.33.10 to configure a new box. That is a publicly routed IP adress, so I'm a bit confused why using this address is suggested. Since I don't own this network, I should not use an address from the 33.33.33.10/8 range. Am I correct in thinking that I should only use either a public address from a network I own, or an address from one of the private ranges as defined in RFC 1918? If so, why does Vagrant documentation suggest otherwise?

  Read the article

• Looking for good Open Source email server

  - by rockinthesixstring

  I'm currently running MailEnable as my email server, it's ok but lacking. I'm looking for a better alternative and am wondering about Open Source. I'm a huge fan of the Smarter Mail, and will pay if it's the best I can get... But I have been learning that there is some good stuff out there in the Open Source community (IE: I've started using PFSense and I love it). Does anyone have any suggestions?

  Read the article

• High latency due to non-presence of a transit provider in my country

  - by nixnotwin

  My ISP, a state owned incumbent, buys bandwidth from different transit providers. Whenever it buys transits it announces only a specific prefix (in most cases a hitherto unused) through the new transit AS. For e.g. if it runs out of bandwidth, it buys bandwidth from a new transit and announces a new prefix through it, while the same prefix is not announced (or announced with lowest metrics, so that the routes are very rarely used) via the old transits which continue to provide bandwidth to it. I am a business customer, so I have a fiber based link to the ISP and a tiny subnet is given to me. The subnet which is provide to me is part of a prefix which is announced by the AS of a transit who, it seems, do not have a presence in my country. So when I do a trace the packets, when they leave my ISP's AS, they take about 275ms to reach the transit providers core router, which is located in USA (half the world away). Also for upstream traffic my ISP uses a transit provider (tier 1) who has a presence in my country. But the return path is always through the transit which is in USA. So, average latency is 400ms. All the users of other ISPs in my country discover my subnet via USA. Even the traffic from neighboring countries, from Europe (which is much nearer) follows the path via USA. Sites using CDNs also resolve to ips in USA. I have informed the ISP NOC about the issue and I have asked them to provide an ip subnet belonging to a prefix announced by a local transit (preferably a tier 1 transit provider) and I am waiting for a reply. My question: Is it a serious issue that I must follow up to get it resolved? When I compared the latency on other providers in my country, it is, in most cases, less than half of my ISPs latency. Why my ISP doesn't announce all its prefixes to all of its transit providers, so that the packets can take efficient and nearest routes to reach prefixes that originate within its network?

  Read the article

• Should I expect ICMP transit traffic to show up when using debug ip packet with a mask on a Cisco IOS router?

  - by David Bullock

  So I am trying to trace an ICMP conversation between 192.168.100.230/32 an EZVPN interface (Virtual-Access 3) and 192.168.100.20 on BVI4. # sh ip access-lists 199 10 permit icmp 192.168.100.0 0.0.0.255 host 192.168.100.20 20 permit icmp host 192.168.100.20 192.168.100.0 0.0.0.255 # sh debug Generic IP: IP packet debugging is on for access list 199 # sh ip route | incl 192.168.100 192.168.100.0/24 is variably subnetted, 2 subnets, 2 masks C 192.168.100.0/24 is directly connected, BVI4 S 192.168.100.230/32 [1/0] via x.x.x.x, Virtual-Access3 # sh log | inc Buff Buffer logging: level debugging, 2145 messages logged, xml disabled, Log Buffer (16384 bytes): OK, so from my EZVPN client with IP address 192.168.100.230, I ping 192.168.100.20. I know the packet reaches the router across the VPN tunnel, because: policy exists on zp vpn-to-in Zone-pair: vpn-to-in Service-policy inspect : acl-based-policy Class-map: desired-traffic (match-all) Match: access-group name my-acl Inspect Number of Half-open Sessions = 1 Half-open Sessions Session 84DB9D60 (192.168.100.230:8)=>(192.168.100.20:0) icmp SIS_OPENING Created 00:00:05, Last heard 00:00:00 ECHO request Bytes sent (initiator:responder) [64:0] Class-map: class-default (match-any) Match: any Drop 176 packets, 12961 bytes But I get no debug log, and the debugging ACL hasn't matched: # sh log | inc IP: # # sh ip access-lists 198 Extended IP access list 198 10 permit icmp 192.168.100.0 0.0.0.255 host 192.168.100.20 20 permit icmp host 192.168.100.20 192.168.100.0 0.0.0.255 Am I going crazy, or should I not expect to see this debug log? Thanks!

  Read the article

• How to make routes on a windows 7 laptop persistent?

  - by askvictor

  I have a number of (windows 7) laptops that normally connect via wireless. We also have a wired network for special purposes. When one of these laptops plugs in to the wired network, at the moment, it makes the wired network the default route. Instead, I would like it to keep the wireless network the default, and route only 10...* through the wired. I can achieve this with: route delete 0.0.0.0 IF 22 route add 10.0.0.0 ... IF 22 (where IF 22 is the wired network interface). But how can I get this to stick? Currently, if the wired network is unplugged then re-plugged, it grabs the default route again. So I want a way of making the wireless network not get the default route, and to make the 10...* network persistent. Is there a hook to run commands after a network connection is established in windows? In linux I would use post-up hooks.

  Read the article

• Changing DNS - Forgot to change MX records for one month - Is there a way to retrieve emails that we

  - by Chris Altman

  We have our own domain. Our email is hosted by Google Apps. We switched web servers and name servers to a new provider. In the switch, I forgot to move the MX record. When people tried to send emails to our domain, there was no bounce back. We fixed the MX record and now receive email. Is there anyway to retrieve the emails that were sent in the month when there was no MX record? I doubt it because there was no MX record on our name server. Where would the emails have gone since they did not bounce back?

  Read the article

• Dovecot/Postfix-mysql e-mail Aliases are not correctly forwarded

  - by jo_fryli

  I recently set up Dovecot/postfix-mysql on my Debian Squeeze Server and I have a bit of a problem. When ever I send a email to an alias ([email protected] forwarded to [email protected] for example) Postfix (or Dovecot, I'm not quite sure) puts this email into a Mailbox rather than forwarding it to the real Mail-Adress. I have tested all the MySQL queries and they all behave the way I intend them to do. foobar dovecot: deliver([email protected]): msgid=<000001385b464c9a-e40af11e-3bf4-49f6-903d-1d2369f6bfb6-000000@barfoo: saved mail to INBOX master.cf main.cf Keep in mind that normal E-Mail sending and receiving works just fine! I have set up my MySQL Tables with Postfixadmin. Thanks for your help!

  Read the article

• Postfix SMTP sends to localhost, ignores MX records set to Google Apps

  - by Kerrick

  I have the MX records for zaltin.com set to the Google Apps domains (aspmx.l.google.com etc.). If an email is sent to [email protected] from most places, it goes to my Google Apps account. However, on the zaltin.com server (Ubuntu 10.04 if it matters), sending via SMTP (postfix), if I send to [email protected] (via the Pony ruby gem if it matters), it simply routes to kerrick@localhost (showing up via the mail command) instead of going to my Google Apps account (where it should show up in my GApps Gmail inbox). Can I make email sent via SMTP on my server, through my server, not go to my server but to Google Apps?

  Read the article

• Configure ubuntu 12.10 to share internet through second NIC with subnetwork

  - by Dan Smith

  I have an Ubuntu 12.10 box with 2 NICs. eth0 is connected to my 192.168.1.X network, which is connected to my home router and out to the internet. I want the other interface, eth1,to support 10.0.0.x and allow devices on that network to access the internet through my ubuntu box. I do not need dhcp on the 10.0.0.x network. Here's a schematic: Internet --- home router ---- ubuntu[eth0:192.168.1.x, eth1:10.0.0.x] --- [10.0.0.x device] How do I configure the ubuntu box to share the internet with devices on that subnetwork? Thanks!

  Read the article

• How can I reroute a sub-domain to localhost + port number?

  - by urig

  I have several web applications running on my developer machine. They mimic our production web applications which are hosted on sub-domain. For example, consider: api.myserver.com - is mimicked by 127.0.0.1:8000 www.myserver.com - is mimicked by 127.0.0.1:8008 and so on... How can I make it so that, on my Windows 7 machine, HTTP calls to "api.myserver.com" (note the lack of port number) are redirected to 127.0.0.1:8000 etc? Note that this needs to apply both to client-side calls (in the browser) and server-side calls (from IIS to Python development server and vice versa). Do I need a proxy to run locally to achieve this? Can you recommend such a tool?

  Read the article

• Single m0n0wall - Two LAN Subnets - How To Setup

  - by SnAzBaZ

  I have two LAN subnets that I need to link together they are 192.168.4.0/24 and 192.168.5.0/24 There is a m0n0wall running on 192.168.4.1. It's LAN connection goes out to our network switch, and it's WAN port goes out to our ADSL modem. WAN is connected via PPPoE. The 192.168.4.0 subnet contains all of our office workstations. The 192.168.5.0 subnet contains development servers and test machines that need to obtain internet access and be "managed" by computers on the 192.168.4.0 subnet, but need to be on their own subnet as well. I have a Draytek 2820N configured on 192.168.5.1 with it's WAN2 port configured as 192.168.4.25 and a default gateway of 192.168.4.1. Machines on the 5.0 subnet can connect to the internet via the m0n0wall just fine. I configured a static route on the m0n0wall LAN interface, Network 192.168.5.0/24 and Gateway 192.168.4.25. Machines on the 5.0 subnet can ping machines on the 4.0 network but the reverse does not work. I configured a new firewall rule on the m0n0wall that allows any traffic on the LAN interface with a source IP of 192.168.4.25 to be allowed. The DrayTek firewall is currently configured to pass all traffic regardless. When I try to ping a machine in the 5.0 subnet from 4.0 I see this in my m0n0wall log: BLOCK 14:45:27.888157 LAN 192.168.4.25 192.168.4.37, type echoreply/0 ICMP So the reply is being sent from the 5.0 subnet but is not being allowed to reach my workstation because the firewall is blocking it. Why is the firewall blocking it ? I hope the explanation of my network is clear, please ask if you require further clarification. Thank you.

  Read the article

• Use same url externally as internally

  - by Nifle

  If I have a web server on my home network I can connect to it from work with http://my.external.ip/whatever/ (assuming NAT and forwarding). Naturally I have a bookmark in my browser that points to http://my.external.ip/whatever/ however when I use that bookmark on my home computer (also behind NAT) the link does not work because my firewall blocks it. (firewall is a old'ish Dlink) What is the best way to fix this issue?

  Read the article

• Server 2003 and XP Client; Why are HTTP connections being silently dropped.

  - by Asa Yeamans

  On my network, my edge-router, a windows 2003 r2 server router with all the latest updates, will drop packets, but only under specific circumstances. I have troubleshot and isolated it down to the most simple configuration i can. There is NO NAT involved. Only fully-public IP addresses. No Firewalls are running either, all ahve been disabled. no packet filters on any interfaces anywhere either. I have a single Windows XP virtual machine and my edge-router(the windows 2003 r2 server, and also a virtual machine) running on a windows 2008 x64 r2 system (running virtual server 2005 as i dont have Intel-VT compatible chip yet). The edge router can access any external http site just fine, no issues. However the windows XP machine is only able to access certain sites. These work: www.google.com www.txstate.edu www.workintexas.com www.thedailywtf.com . These Dont: www.yahoo.com www.utexas.edu en.wikipedia.org slashdot.org www.bing.com. I have removed all possibility of DNS issues by connecting with net-cat from the XP box and sending GET /\r\nHost: \r\n\r\n and that connection replicates the issue as well. The network setup: My statically assigned IP block: x.x.x.168/29 DSL Modem -----PPPoE Connection---- x.x.x.169[EdgeRouter] [EdgeRouter]x.x.x.170 -----Virtual Ethernet----- x.x.x.174 [Test2] Test2's Default gateway is x.x.x.170 and test2 can ping any and every valid, accessible, public IP address with no packet loss what-so-ever. If i connect directly over PPPoE from test2 (the XP box) everything works just fine... Im at my wits end, i have NO IDEA whats causing this.

  Read the article

• What's required to enable communication between two IP ranges located behind one switch?

  - by Eric3

  Within our co-located networking closet, we have control over two ranges of 254 addresses, e.g. 64.123.45.0/24 and 65.234.56.0/24. The problem is, if a host has only one IP address, or a block of addresses in only one range, it can't contact any of the addresses in the other subnet. All of our hosts use our hosting provider's respective gateway, e.g. 64.123.45.1 or 65.234.56.1 A host on the 64.123.45.0/24 range can contact the 65.234.56.1 gateway and vice-versa Everything in our closet is connected to an HP ProCurve 2810 (a Layer 2-only switch), which connects through a Juniper NetScreen-25 firewall to the outside world What can I do to enable communication between the two ranges? Is there some settings I can change, or do I need better networking equipment?

  Read the article

• Prevent users from Router 2 seeing Router 1 computers

  - by Patrick Robert Shea O'Connor

  I've got 2 Netgear N300 (WNR2000v3) routers. Here's my setup: Modem Router 1 Private Users/Router 2 Public Wireless Users on "Guest" Network. I want to prevent users who are connected to Router 2's "Guest" network from accessing anything that is connected to Router 1. There is an option when setting up the "Guest" network called "Allow guest to access My Local Network" which I thought if unchecked would do this very thing; however, I can still access files and such of computers connected to Router 1. Router 1 assigns 192.0.0.x IP addresses, Router 2 assigns 10.0.0.x IP addresses, how can they even see each other? Do I need to change the subnet or something else?

  Read the article

• Using a 3g usb dongle as Cisco router access point

  - by beakersoft

  We have an office opening, and we aren't going to have comms into the building when management want the building to open. Our only option (I think) Is to try and hook up a 3/4g dongle to something to act as the access point, and send all the traffic via that. The model of router we use wont support the usb dongle, so we need some sort of 'bridge' My idea was to build a Linux box, plug the dongle into that and then via the Ethernet ports plug the router in. We need the Cisco router in the equation as we create VPN connections over that back to head office. My question is will this work?

  Read the article

• No Internet access while being connected to VPN using Cisco VPN Client 5.

  - by szeldon

  Hi, I have an access to corporate VPN using Cisco VPN Client 5.0.00:0340, but when I'm connected to it, I don't have an Internet access. I'm using Windows XP SP3. As it was suggested here http://forums.speedguide.net/showthread.php?t=209167 , I tried to enable "Allow local LAN Access" but it doesn't work. I also tried a second solution - deleting entry using "route" command, but it didn't help. I used "route delete 192.168.100.222". It's a third day of my attempts to solve this issue and I don't have an idea what else to do. I'm not very experienced in VPN stuff, but I know something about networking. Basing on my knowledge, I think that it's theoretically possible to achieve Internet access using my local network and only corporate stuff to be routed using VPN connection. I think that theoretically this should look like this: every IP being inside by corporation - VPN interface IP every other IP - my ethernet interface I've tried many possibilities of how to change those routes, but neither of them work. I'd really appreciate any help. My route configuration before connecting to VPN: =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 c0 a8 de 79 01 ...... Atheros AR5006EG Wireless Network Adapter - Teefer2 Miniport 0x10005 ...02 00 4c 4f 4f 50 ...... Microsoft Loopback Card 0x160003 ...00 17 42 31 0e 16 ...... Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller - Teefer2 Miniport =========================================================================== =========================================================================== Active routes: Network Destination Netmask Gateway Interface Metrics 0.0.0.0 0.0.0.0 192.168.101.254 192.168.100.222 10 10.0.0.0 255.255.255.0 10.0.0.10 10.0.0.10 30 10.0.0.10 255.255.255.255 127.0.0.1 127.0.0.1 30 10.255.255.255 255.255.255.255 10.0.0.10 10.0.0.10 30 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.100.0 255.255.254.0 192.168.100.222 192.168.100.222 1 192.168.100.222 255.255.255.255 127.0.0.1 127.0.0.1 1 192.168.100.255 255.255.255.255 192.168.100.222 192.168.100.222 1 224.0.0.0 240.0.0.0 10.0.0.10 10.0.0.10 3 224.0.0.0 240.0.0.0 192.168.100.222 192.168.100.222 1 255.255.255.255 255.255.255.255 10.0.0.10 10.0.0.10 1 255.255.255.255 255.255.255.255 192.168.100.222 192.168.100.222 1 255.255.255.255 255.255.255.255 192.168.100.222 2 1 Default gateway: 192.168.101.254. =========================================================================== My route configuration after connection to VPN: =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 c0 a8 de 79 01 ...... Atheros AR5006EG Wireless Network Adapter - Teefer2 Miniport 0x10005 ...02 00 4c 4f 4f 50 ...... Microsoft Loopback Card 0x160003 ...00 17 42 31 0e 16 ...... Marvell Yukon 88E8055 PCI-E Gigabit Ethernet Controller - Teefer2 Miniport 0x170006 ...00 05 9a 3c 78 00 ...... Cisco Systems VPN Adapter - Teefer2 Miniport =========================================================================== =========================================================================== Active routes: Network Destination Netmask Gateway Interface Metrics 0.0.0.0 0.0.0.0 10.251.6.1 10.251.6.51 1 10.0.0.0 255.255.255.0 10.0.0.10 10.0.0.10 30 10.0.0.0 255.255.255.0 10.251.6.1 10.251.6.51 10 10.0.0.10 255.255.255.255 127.0.0.1 127.0.0.1 30 10.1.150.10 255.255.255.255 192.168.101.254 192.168.100.222 1 10.251.6.0 255.255.255.0 10.251.6.51 10.251.6.51 20 10.251.6.51 255.255.255.255 127.0.0.1 127.0.0.1 20 10.255.255.255 255.255.255.255 10.0.0.10 10.0.0.10 30 10.255.255.255 255.255.255.255 10.251.6.51 10.251.6.51 20 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.100.0 255.255.254.0 192.168.100.222 192.168.100.222 10 192.168.100.0 255.255.254.0 10.251.6.1 10.251.6.51 10 192.168.100.222 255.255.255.255 127.0.0.1 127.0.0.1 10 192.168.100.255 255.255.255.255 192.168.100.222 192.168.100.222 10 213.158.197.124 255.255.255.255 192.168.101.254 192.168.100.222 1 224.0.0.0 240.0.0.0 10.0.0.10 10.0.0.10 30 224.0.0.0 240.0.0.0 10.251.6.51 10.251.6.51 20 224.0.0.0 240.0.0.0 192.168.100.222 192.168.100.222 10 255.255.255.255 255.255.255.255 10.0.0.10 10.0.0.10 1 255.255.255.255 255.255.255.255 10.251.6.51 10.251.6.51 1 255.255.255.255 255.255.255.255 192.168.100.222 192.168.100.222 1 255.255.255.255 255.255.255.255 192.168.100.222 2 1 Default gateway: 10.251.6.1. ===========================================================================

  Read the article

• How can I make outbound requests from two servers that appear to come from the same IP address

  - by Brad

  I am making calls from an ec2 instance to a third party web service (over which I have no control). I would like to be able to scale horizontally, so that I can make these calls from multiple ec2 instances, but the web service I'm calling whitelists my IP, and for the sake of discussion let's assume I can't get another IP address whitelisted. How can I send requests from 2+ machines that appear to the web service to be from the same IP address? Thanks!

  Read the article

• How can the route between two private IPs go via public IPs?

  - by Gilles

  I'm trying to understand what this output from traceroute means. I changed the IP addresses for privacy but retained the public/private IP range distinction. traceroute.db -e -n 10.1.1.9 traceroute to (10.1.1.9), 30 hops max, 60 byte packets 1 10.0.0.1 0.596 ms 0.588 ms 0.577 ms 2 10.0.0.2 1.032 ms 1.029 ms 1.084 ms 3 10.0.0.3 3.360 ms 3.355 ms 3.338 ms 4 23.0.0.4 3.974 ms 4.592 ms 4.584 ms 5 23.0.0.5 13.442 ms 13.445 ms 13.434 ms 6 45.0.0.6 13.195 ms 12.924 ms 12.913 ms 7 67.0.0.7 52.088 ms 51.683 ms 52.040 ms 8 10.1.1.8 46.878 ms 44.575 ms 44.815 ms 9 10.1.1.9 45.932 ms 45.603 ms 45.593 ms The first 10.0.* range is inside my organisation. The last 10.1.* range is another site of my organisation. The intermediate addresses belong to various ISPs. I expect that there is some kind of VPN between the two sites, but I don't know much about our network topology. What I don't understand is how the route can go from a private address through public addresses back into private addresses. Searching led me to Public IPs on MPLS Traceroute, which gives a possible explanation: MPLS. Is MPLS the only possible or most likely explanation? Otherwise what does this tell me about our network infrastructure? Bonus question for my edification: in this scenario, who is generating the ICMP TTL exceeded packets and if relevant mangling their source and destination addresses?

  Read the article

• OpenVZ multiple networks on CTs

  - by user6733

  I have Hardware Node (HN) which has 2 physical interfaces (eth0, eth1). I'm playing with OpenVZ and want to let my containers (CTs) have access to both of those interfaces. I'm using basic configuration - venet. CTs are fine to access eth0 (public interface). But I can't get CTs to get access to eth1 (private network). I tried: # on HN vzctl set 101 --ipadd 192.168.1.101 --save vzctl enter 101 ping 192.168.1.2 # no response here ifconfig # on CT returns lo (127.0.0.1), venet0 (127.0.0.1), venet0:0 (95.168.xxx.xxx), venet0:1 (192.168.1.101) I believe that the main problem is that all packets flows through eth0 on HN (figured out using tcpdump). So the problem might be in routes on HN. Or is my logic here all wrong? I just need access to both interfaces (networks) on HN from CTs. Nothing complicated.

  Read the article

• How to securly join two networks together over the Internet?

  - by Pyrolistical

  Let's say there are two locations. Both locations have their own fast Internet connections. How do you join these two networks together such that every computer can see every other computer? Do you need a domain controller, or can you do this with workgroups? EDIT The obvious solution seems to be VPN, but can VPN be implemented on the routers only? Can the computers on the network be configuration free?

  Read the article

• How to build an outbound load balancer with linux?

  - by matnagel

  We have a small house in the countryside and there is no fixed broadband, so we had a mobile flatrate first, and for 2 people with 2 computers it was too slow, so now we have 2 flatrates for 2 client machines. So I pay 2 flatrates and have double bandwith theoretically. There is a local network in the house that connects everything. But when I am alone I wonder how I can use both connections at the same time. I want to build a solution where I can browse the web and page requests are spread between the 2 connections. I imagine there are expensive routers who can split the traffic between 2 lines. But is there a good way to do it with linux? The solution I am looking for will split the requests already for one page (multiple images, css files, javascrfipt files) between the two lines.

  Read the article

• Do I need a VPN to secure communication over a T1 line?

  - by Seth

  I have a dedicated T1 line that runs between my office and my data center. Both ends have public IP addresses. On both ends, we have a T1 routers which connect to SonicWall firewalls. The SonicWalls do a site-to-site VPN and handle the network translation, so the computers on the office network (10.0.100.x) can access the servers in the rack (10.0.103.x). So the question: can I just add a static route to the SonicWalls so each network can access each other with out the VPN? Are there security problems (such as, someone else adding the appropriate static route and being able to access either the office or the datacenter)? Is there another / better way to do it? The reason I'm looking at this is because the T1 is already a pretty small pipe, and having the VPN overhead makes connectivity really slow.

  Read the article

• Using iptables to forward traffic destined for specific ip via specific interface

  - by shapeshifter

  I want to forward traffic destined for a specific ip from my internal network via a specific interface. I have two interfaces which are currently load balanced. I need all requests for a certain ip to go out via eth0 otherwise my external ip changes and sessions are dropped. eg. all requests from 10.1.1.1/24 to ip 11.22.33.44 on port 443 must go out via interface eth0. How can I do this with iptables?

  Read the article

• Is it possible to dynamically adjust the priority of outgoing emails?

  - by davethegr8

  This is more of a theoretical question, but is it possible to dynamically, and on an ongoing basis, adjust the priority of emails in the mail queue? For example, for all mail, set it's priority (p) to 1 (meaning send immediately). If N emails in the last M share similar or identical content, adjust the priority of this email such that it's priority is in the range [0..1] so that p is equal to 1 - N/M and other email can get sent before the similar/identical stuff. Or, if you have another idea or standard what is it? Some background: Someone put a mail() call in an infinite loop... And now we have to wait for the mail queue to catch up before anyone can send or receive mail again.

  Read the article

< Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >