Search Results

Search found 18556 results on 743 pages for 'facebook connect'.

Page 103/743 | < Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >

• how to connect public web server to internal LAN

  - by DefSol

  I have a VPS which is my public web server for all my clients. It's running server 2008 and I would like to have it connect via secure connection to my internal LAN. I would like this to be a route so access is bi-derectional. Have read about Server & Domain isolation, but am concerned this may prevent public views to the webs sites on the server. I currently have a PPTP tunnel, but I'm wanting better security (IPSec or SSL etc) and it's not given my bi derectional access. (In fact my backups aren't copying accross but this could be an acl issue) The goal is to provide easy/automated backups of data & sql db's to my internal LAN, as well as a means to provision new sites & db's from a workflow occuring internally. Internal lan is windows based with ISA 2006 at the perimeter. Thanks

  Read the article

• Unable to connect my computer from LAN (http, smb) in UBUNTU 10.04

  - by Abdul Majeed

  I installed ubuntu 10.04, Apache, PHP, mysql, smb. Everything work fine in locally in my IP. When i trying to access my computer from LAN (other computer), it shows unable to connect. when i ping my IP from remote computer, its pinging OK. I can access internet, and all other systems (http, smb). But the problem is no one can't access my computer remotely in my LAN network. My ip is 192.168.85.105 and i want access(Appaceh,SMB) from 192.168.85.10. Is there any proxy firewall settings? I had tried following commands.. sudo iptables -F or sudo iptables-restore [logout require] If it does not work then try to disable net-filter sudo ufw --disable Please give me the solution.

  Read the article

• Qnap won't connect to Windows Share

  - by thetrashcan

  I have a qnap nmp-1000 in my network and would like to stream my films from my win7 laptop to the nmap-1000 device. I just managed to do so with upnp sharing, but I would like to, for security reasons, share my files over a shared folder which is password protected. My problem is when I'm searching for devices on my network with the qnap then it won't find any. When I try to mount a remote disk on my qnap it will just fail with an connection failed message. But when I try to connect to the qnap device with my laptop, it does this succesfully. Can someone guide me through on how to get my setup working?

  Read the article

• Connect a ssd externally such that hdparm is fully supported

  - by student

  I am just trying some hdparm magic with my new ssd (samsung 840 pro). However I don't want to change my drive over and over so it would be great if I could connect it externally to my laptop. I have a cheap sata-usb Adapter, but I feel it doesn't support the ATA commands send by hdparm. So what's the best way to do this? Are there sata-usb Adapters which fully support the hdparm things? Would it be a good idea to buy a sata-esata adapter to get full control over the drive?

  Read the article

• strange behaviour - dhclient needs to be run twice in order to connect to wireless

  - by splicer

  I am trying to connect my to my wlan without the use of NetworkManager. I run the following commands after boot: iwconfig wlan0 enc <WEP passwd> mode managed essid <name> channel 6 ifconfig wlan0 up dhclient wlan0 At this point, dhclient stalls for ages (perhaps 2 minutes), then it returns with PING 192.168.1.254 (192.168.1.254) from 192.168.1.65 wlan0: 56(84) bytes of data. --- 192.168.1.254 ping statistics --- 3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 3000ms pipe 3 .. The strange thing is that when I run pkill dhclient; dhclient wlan0 right after this, it connects in about <3 seconds. Any idea what could be the cause of this problem? Edit: oh, and I did try using the -timeout flag on dhclient but that didn't seem to make any difference (it still stalled for ages).

  Read the article

• Unable to connect guest using VMWare Player

  - by eLAN

  I'm running RedHat server 5.3 as guest on Window XP VMware palyer. the network setting is set to "Host Only", but I have tries all other settings. I'm able to ping the guest machine, but I'm unable to connect it in any other way including webserver, Tomcat, Telnet, ssh. all of the services above are working from within the guest (using localhost). Guest firewall and SELinux are disabled. any idea on what I should check next? every idea will be appreciated... thnaks Ilan

  Read the article

• BITS http download job fails to connect for owner Local SYSTEM account

  - by MikeT

  A service I have written that uses BITS (Background Intelligent Transfer Service) to auto update itself is having a problem on some machines (Windows 7 so far). I have been investigating and have discovered that some of the jobs that my service adds to the bits queue are failing immediately with the error code 0x80072efd (a connection with this server could not be established). The is not problem with connecting to the server for the download as it works fine on the same machine using IE (or any other web browser) and other clients can connect and update from the same server. I tried using the BITSADMIN.exe tool to add the jobs manually and they worked ok. I then changed the account my service was running under to the network service account so the bits jobs would be created with a different owner and the jobs completed successfully. My question is I don't want to run my service as this account as it wont have the required local permissions, so how to I change the permissions of the local system user to allow it to download from the HTTP source, I'm not aware of any way of this being restricted for this account but it obviously is.

  Read the article

• to measure throughput of testing device connect to server via AP

  - by samantha

  Description of project- I have a test tool to which DUT connects. The test tool has an access point in it and once DUT get connected to it via mac address we check RSSI and some other features of WiFi of DUT. Now I am wondering is there is any way I can measure throughput of Device under test via mac address of DUT from server side. Test-tool has LINUX fedora 11 in it and major coding is done in c/C++ and json command. Previously, I have tried to install ftp server on test-tool and DUT can connect to it and we can measure the throughput or data transfer rate, but this is not feasible solution as it requires lot of intervention from DUT. What I am interested in is 1) To run some script on server side /test tool and it gives me throughput of bandwidth of connected device may be via mac address of DUT OR 2) Server script transfer some files/packets to DUT and we can measure the throughput. Coding is not a major challenge at this stage , I just need some tool which requires minimum intervention from DUT.

  Read the article

• Random users randomly being unable to connect to my static content domain

  - by jls33fsls

  I store all of my images, js, and css files on a separate domain to try and speed up page load times (it isn't a CDN, just a separate domain on the same server). This works fine for 99% of the users, 99% of the time. However, there are users that randomly are unable to connect to the static content domain for periods of 1-5 hours. They can go to the main site, but no images will load and everything is just white because no css is being loaded. If they go to the static content domain itself, the page just idles for a while and then times out with a blank white page, no error messages. I have no idea what could be causing this, and it hasn't happened to me, any ideas? I am running Apache on CentOS 5.5.

  Read the article

• VM can't connect to outside in bridged mode

  - by Kamal

  Hi Guys, I am not able to ping any machine(not even the host) from Guest VM in bridged mode. But I got an IP which is on the same subnet as host. I can ping my guest VM from the host and can use ssh to connect to the guest. I am using Vmware workstation 6.5. Guest VM is a centos VM and host is windows xp. Every thing works fine in NAT mode. Any clues as to what could be happening. I tried disabling all the firewalls I have.

  Read the article

• Amazon EC2 - Unable to connect to MySQL

  - by alexus

  I'm having issue connecting from one VM to another # nmap -p3306 ip-XX-XX-XX-XX.ec2.internal Starting Nmap 6.40 ( http://nmap.org ) at 2014-06-10 17:50 EDT Nmap scan report for ip-XX-XX-XX-XX.ec2.internal (XX.XX.XX.XX) Host is up (0.000033s latency). PORT STATE SERVICE 3306/tcp closed mysql Nmap done: 1 IP address (1 host up) scanned in 1.05 seconds # in my Security Group I allowed Inbound connectivity via port TCP, portrange 3306 and Source 0.0.0.0/0, so theoratically it should work, but in reality it doesn't( I'm running red hat enterprise linux 7 on both VMs. mariadb.service running fine on another VM and I am able to connect to it locally. DB's: # netstat -anp | grep 3306 tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN 2324/mysqld # iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination # Any ideas what else I missed?

  Read the article

• Connect to CentOS LAMP instance from Windows PCs

  - by Gnanesh

  I have a CentOS 6 machine running on our network which has a simple LAMP installation on it. I have some files there which I would want to access through other Windows PC which I am able to do so using the IP address of the CentOS machine. Since the IP address of the CentOS machine also could be dynamic I would want to connect to it using the computer / host name But I am not able to do so using the computer / host name of the CentOS machine. Can someone help me point out what I may be missing and help me out to resolve this?

  Read the article

• Connect to wired and wireless networks at same time, Ubuntu

  - by Gary Chambers

  Currently, I have a media PC running Ubuntu 10.04 that I am trying to connect via a wired network cable directly to a NAS box, and wirelessly to the router. This works no problem after I run sudo /etc/init.d/networking restart but I can't get both interfaces to come up on system startup. My /etc/network/interfaces file reads as follows: auto eth0 iface eth0 inet static address 10.0.1.2 netmask 255.255.254.0 broadcast 10.0.1.255 network 10.0.1.0 auto wlan2 iface wlan2 inet dhcp As I say, I know this works, because I can get it to work by restarting the network interfaces, but I can't bring them both up on system startup. Does anyone know why this might be?

  Read the article

• Connect ADSL modem SMC7904WBRA-N to CISCO RV082

  - by Cy.

  I have a SMC7904WBRA-N ADSL modem/router that connects to the internet with a static IP given by the provider. I've received a RV082 to create a VPN connection which is having problems to connect to the remote VPN Server. After many tries we deduced that the SMC7904WBRA-N is being problematic with the NAT and I have been suggested to put the SMC router into the appropriate DSL bridging mode so the RV082 gets direct access to internet with the static IP. Can you give me any hints on how could this be done? Which mode is that?

  Read the article

• Connect Lenovo Thinkpad Edge e120 to WQHD display (such as Dell U2711) through HDMI

  - by Fulvio

  On paper, the HDMI version of the Lenovo Thinkpad Edge e120 is 1.3, which supports WQHD. Does it actually work? I want to connect the e120 to a WQHD display, such as the Dell U2711 or an Apple Cinema Display. I run Windows 7 Ultimate and latest drivers. The e120 I think has the Intel HD Graphics 3000 onboard chipset. I don't have the chance to test out the e120 with neither of these displays, so I'm seeking for an opinion from those who have tried. Thank you

  Read the article

• Connect android to database

  - by danny

  I am doing a school project where we need to create an android application which needs to connect to a database. the application needs to gain and store information for people's profiles on the database. But unfortunatly we are a little bit stuck at this point because there are numerous ways to link the application such as http request through apache or through the SOAP/REST protocol. But it's really hard to find good instructions or tutorials on the problem since I can't really find them. Maybe that's cause i'm probably using the wrong words on google. Unfortunately I have little relevant information. So if anyone can help me with finding relevant links to good online tutorials or howto's than those are very welcome.

  Read the article

• Can't connect to IIS7 on one of my machines

  - by user38974

  Hello, I have 2 computers, both running Win7 Professional x64. Computer "A" (192.168.0.10) is my work machine, it contains my tools etc. Computer "B" (192.168.0.15) is supposed to be my build server / web server for my projects I've installed IIS on "B", and installed IIS7 remote manager on "A". I'm trying to connect from A's IIS7 Manager to B's IIS but I fail. I have little knowledge of IIS, and I feel that's the main reason. I can ping B from A and get positive results so the machines do see each other. A and B are in the same workgroup but not in a domain (if that matters) - they're in my home network. What do I need to do to "see" B's IIS?

  Read the article

• Not able to connect to internet in RHEL 5

  - by chankey007

  I just installed red hat enterprise 5 in my laptop and on desktop both. In desktop it is working fine but in laptop it is not showing the eth device. (I tried ifconfig only lo is there). I tried ifup eth0 still nothing happened. The network service in /etc/sysconfig/network-scripts/ifcfg-eth0 and in /etc/sysconfig/network are enable. I had ubuntu in my laptop before and I faced same problem with that too. Is there any problem with my laptop? I have my system on dual boot and in win7 networking is running fine. I am not able to connect to the internet only, other devices are working fine. System conf: Sony vaio E series. 3 GB RAM, intel core i3 2.13 GHZ.

  Read the article

• Not able to connect to internet in RHEL 5

  - by chankey007

  I just installed red hat enterprise 5 in my laptop and on desktop both. In desktop it is working fine but in laptop it is not showing the eth device. (I tried ifconfig only lo is there). I tried ifup eth0 still nothing happened. The network service in /etc/sysconfig/network-scripts/ifcfg-eth0 and in /etc/sysconfig/network are enable. I had ubuntu in my laptop before and I faced same problem with that too. Is there any problem with my laptop? I have my system on dual boot and in win7 networking is running fine. I am not able to connect to the internet only, other devices are working fine. System conf: Sony vaio E series. 3 GB RAM, intel core i3 2.13 GHZ.

  Read the article

• Add domain user as local admin in Windows 7 using VPN to connect to domain

  - by kev

  I am rebuilding my work computer from scratch and need to add my domain user as a local admin on my computer. I have successfully added my PC to the domain, but I cannot add my domain user account to the local admins. I have tried to do the following: Connect to the work domain using a Windows VPN Add my computer to the work domain Start right click on Computer Manage - go to Users and Groups right click on Administrators group and add my domain user The problem is that after adding my domain user to the Administrators group, I don't see my domain user under the Local Users group. When I try to log on as my domain user I get the following error message: There are currently no logon servers available to service the logon request Any ideas?

  Read the article

• Disable Thunderbird "failed to connect" notifications

  - by The Electric Muffin

  My network manager doesn't start until I log in, so for the first ten seconds or so after I login I have no Internet connection. The problem is that I have Thunderbird set to automatically start on login, so it helpfully tells me it "failed to connect" every time I log in. Also, my Internet connection isn't too reliable, so I sometimes get those messages even when I'm supposedly connected. Is there any way to disable these notifications, while still allowing the ones about new mail? Computer info: Thunderbird 15.0 $ uname -a Linux [HOSTNAME REDACTED] 3.2.0-29-generic #46-Ubuntu SMP Fri Jul 27 17:03:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux Probably irrelevant: NetworkManager Version 0.9.0.1 (nm09 20120407) KDE Platform Version 4.8.4 (4.8.4)

  Read the article

• How to connect two subnet with Windows Server?

  - by 9dan

  Hello, I have some work to do in a small office. This office has two separate Internet connections. One is a kind of DSL line and connected through the Internet sharing router (DHCP). One is a leased line with public IP adresses (No DHCP). This leased line provide only 30 IP addresses and the gateway is provided by the ISP. Some workers use private IP provided by the router, some workers use manually setup public IP. There is a Windows 2008 R2 server with two NICs, connected to each lines. I want to connect/merge(?)/bridge(?) two subnet with this server so that users from the different subnet can access each other. How can I accomplish this? Something like, add gateway function to this server and public IP users change the gateway to point this server.. It it possible ? Sorry for my rambling. Thanks in advance.

  Read the article

• MMS gets hostname from uname and can't connect to it

  - by Adam Monsen

  I'm trying to get 10gen's MongoDB Monitoring Service monitoring my 3-node replica set. The replica set running in an AWS VPC. Each node runs on a different [virtual] machine. Assume their IPs are 192.168.1.1 (primary or secondary), 192.168.1.2 (primary or secondary), 192.168.1.3 (arbiter). From a quick look at the source, MMS appears to get the hostname of the machine it is running on like so: platform.uname()[1] For my VPC EC2 instance, this returns something like ip-192-168-1-1 MMS then tries to connect to this hostname, which does not resolve. I'd rather just use IP addresses (since they're always static), but it seems like the hardcoded use of platform.uname()[1] in mmsAgent.py precludes that. So, what's an elegant way out of this? Hack /etc/hosts? I'm not setting up a DNS server just for this. Maybe I'm just misunderstanding how to configure MMS.

  Read the article

• Cannot connect to IIS 7 from localhost

  - by Wout

  I cannot connect to the local IIS 7 using "http://localhost" in IE. "http://127.0.0.1" doesn't work either. The strange thing is that if I add a binding on e.g. port 81, then I can reach "http://localhost:81". Also turning off the firewall on the local machine doesn't help. The site is reachable from the internet. The local requests don't seem to hit IIS (no entries in the IIS log files). IIS is hosted on Windows Server 2008 R2 from behind a hardware firewall device. Note that I'm a programmer, not a network administrator, so I'm having a hard time trouble shooting this.

  Read the article

• WSS "Cannot connect to the configuration database"

  - by Tim

  I have 64-bit WSS 3.0 installed on a 64-bit Windows 2003 Server. After installing WSS 3.0 I switched IIS to run in 32-bit emulation mode as we have some applications that require this. I'm getting a "Cannot connect to the configuration database" trying to get to the Central Admin page and wondered if: a. The setup I have won't work and I'm wasting my time trying to figure this out. or b. If anyone has any suggestions for resolving the database connection issue? The identity of the app pool that WSS runs under has all the required permissions in SQL so far as I can tell. Any help would be appreciated!

  Read the article

< Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >