Search Results

Search found 4731 results on 190 pages for 'ram rachum'.

Page 103/190 | < Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >

• Q8300 Core-2 Quad vs X3360 Xeon

  - by alchemical

  I'm looking at this ABMX server, and trying to decide on the CPU. I'm purchasing 2 servers, to be used as dedicated web and DB servers for a web site that has low traffic now but could ramp up quickly. Just trying to decide if it is worth about $200 more (per server) for the Xeon vs the core-2. Passmark rates them at 3567 and 4153, which didn't seem that different. I'm not planning at this point to need virtualization. I did hear rumors that Xeon stands up better in a 24/7 server environment, but heard others say there wasn't that much difference. Planning to run Windows Server 2008, likely the R2 release, with 8GB RAM.

  Read the article

• Booting large ISO through PXE

  - by Devator

  I currently have a FOG server (which works perfectly fine) and I'm trying to boot Windows 7 through it (with memdisk). But, since the ISO is rather large (more than 6 GB) it will try to put the ISO into memory and then boot however it crashes with the error message not enough memory to load specified image. The systems here don't have 6 GB of RAM so I need another way to boot it. I am aware of WDS and SCCM, however I want todo this with FOG. Is there any way to boot the ISO and install Windows through FOG?

  Read the article

• Corrupt file indicative of corrupt hard drive?

  - by Elipsicon

  I have noticed that two files on my (almost full) 2 TB hard drive have been corrupted. One file has 20 kB (!) corrupted, i.e. consecutive 20 kB have changed, even though the modification date of the file hasn't changed and I haven't worked with this file for over a year. This tells me that something "below" the file system level has messed with the data and the only thing I can think of is hardware failure, most likely hard disk failure. I've tested my RAM already and it works flawlessly. I'm using ext4 on Linux, if that is of any help. Is this normal? Is it time to change my hard drive disk before something worse happens? What can I do to prevent that from happening in the future? Is there some built-in feature of, or extension to ext4 that includes additional error correcting code and/or watches files for changes that haven't been caused by the OS?

  Read the article

• What advantage to I have if I use 64bit libraries?

  - by RadiantHex

  Hi folks, I see many people go crazy about 64bit libraries, and preferring them in general to the 32bit counter parts. I realise there is a lot of talk that gets lost in translation, and that the 64bit can be often over-valued. The setting is libraries that are called on web application, I'm aware that a new instance of the web app is generated for each hit. Therefore I'm thinking that 64bit is not necessary as the instances in no way surpass 2Gb of RAM usage. Help would be much appreciated! :)

  Read the article

• Can I provision half a core as a virtual CPU?

  - by ramdaz

  I am virtualization newbie. Please advise on these questions. Please note using a commercial VM software like Citrix or VMware is not a choice for me. I have at my disposal a couple of 2x 4 core servers with 32 GB RAM. I need to create 16 VMs on each server to test some web applications. Can I provision half a core as a virtual CPU for each VM? To my best knowledge I can't do so on Xen. Is it possible on KVM or some other free open source VM solution? If it's not possible to assign half a core, how do I ensure that uniform processing power is available for all VMs? Since the job is to create separate instances for hosting 16 web apps in a physical server, do you recommend setting up a private cloud using Ubuntu Enterprise Cloud as a better option? Is there HA solution under KVM, like Remus for Xen?

  Read the article

• Out of memory Problem

  - by Sunil

  I'm running a C++ program in Ubuntu 10.04 (32-bit system architecture). If I calculate the amount of memory that my program uses, it comes up to 800MB. I have a 4GB RAM in place. But still before the program even finishes it throws an out of memory exception. Why is that happening ? Is it because of the structure of the memory or implementation problems or what could possibly trigger this issue ? I've had seen this problem quite a number of times before but never understood the reason behind it. Have any of you handled this case before ?

  Read the article

• What is the best memory supported by Asus Rampage Formula (1) motherboard

  - by James

  I'm rebuilding a PC from old components I have and I want to know what are the best ram sticks for the Asus Rampage Formula (The first motherboard in the Rampage Formula range) According to the Asus website (HERE) the maximum supported memory is 8GB but when I search through the memory compatibility list there's nothing above 2046mb and the motherboard only supports single or dual-channel memory. Can anyone point me in the direction of a more comprehensive list of compatible memory? Or does anyone know where I can ask about memory compatibility? Note: As far as I know, this model motherboard is no longer in production.

  Read the article

• How do I make Linux recognize a new SATA /dev/sda drive I hot swapped in without rebooting?

  - by Philip Durbin

  Hot swapping out a failed SATA /dev/sda drive worked fine, but when I went to swap in a new drive, it wasn't recognized: [root@fs-2 ~]# tail -18 /var/log/messages May 5 16:54:35 fs-2 kernel: ata1: exception Emask 0x10 SAct 0x0 SErr 0x50000 action 0xe frozen May 5 16:54:35 fs-2 kernel: ata1: SError: { PHYRdyChg CommWake } May 5 16:54:40 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:45 fs-2 kernel: ata1: device not ready (errno=-16), forcing hardreset May 5 16:54:45 fs-2 kernel: ata1: soft resetting link May 5 16:54:50 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:54:55 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:54:55 fs-2 kernel: ata1: soft resetting link May 5 16:55:00 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:05 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:05 fs-2 kernel: ata1: soft resetting link May 5 16:55:10 fs-2 kernel: ata1: link is slow to respond, please be patient (ready=0) May 5 16:55:40 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:40 fs-2 kernel: ata1: limiting SATA link speed to 1.5 Gbps May 5 16:55:40 fs-2 kernel: ata1: soft resetting link May 5 16:55:45 fs-2 kernel: ata1: SRST failed (errno=-16) May 5 16:55:45 fs-2 kernel: ata1: reset failed, giving up May 5 16:55:45 fs-2 kernel: ata1: EH complete I tried a couple things to make the server find the new /dev/sda, such as rescan-scsi-bus.sh but they didn't work: [root@fs-2 ~]# echo "---" > /sys/class/scsi_host/host0/scan -bash: echo: write error: Invalid argument [root@fs-2 ~]# [root@fs-2 ~]# /root/rescan-scsi-bus.sh -l [snip] 0 new device(s) found. 0 device(s) removed. [root@fs-2 ~]# [root@fs-2 ~]# ls /dev/sda ls: /dev/sda: No such file or directory I ended up rebooting the server. /dev/sda was recognized, I fixed the software RAID, and everything is fine now. But for next time, how can I make Linux recognize a new SATA drive I have hot swapped in without rebooting? The operating system in question is RHEL5.3: [root@fs-2 ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.3 (Tikanga) The hard drive is a Seagate Barracuda ES.2 SATA 3.0-Gb/s 500-GB, model ST3500320NS. Here is the lscpi output: [root@fs-2 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0a.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0d.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0e.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) Update: In perhaps a dozen cases, we've been forced to reboot servers because hot swap hasn't "just worked." Thanks for the answers to look more into the SATA controller. I've included the lspci output for the problematic system above (hostname: fs-2). I could still use some help understanding what exactly isn't supported hardware-wise in terms of hot swap for that system. Please let me know what other output besides lspci might be useful. The good news is that hot swap "just worked" today on one of our servers (hostname: www-1), which is very rare for us. Here is the lspci output: [root@www-1 ~]# lspci 00:00.0 RAM memory: nVidia Corporation MCP55 Memory Controller (rev a2) 00:01.0 ISA bridge: nVidia Corporation MCP55 LPC Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation MCP55 SMBus (rev a3) 00:02.0 USB Controller: nVidia Corporation MCP55 USB Controller (rev a1) 00:02.1 USB Controller: nVidia Corporation MCP55 USB Controller (rev a2) 00:04.0 IDE interface: nVidia Corporation MCP55 IDE (rev a1) 00:05.0 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.1 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:05.2 IDE interface: nVidia Corporation MCP55 SATA Controller (rev a3) 00:06.0 PCI bridge: nVidia Corporation MCP55 PCI bridge (rev a2) 00:08.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:09.0 Bridge: nVidia Corporation MCP55 Ethernet (rev a3) 00:0b.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:0f.0 PCI bridge: nVidia Corporation MCP55 PCI Express bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:18.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] HyperTransport Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Miscellaneous Control 00:19.4 Host bridge: Advanced Micro Devices [AMD] K10 [Opteron, Athlon64, Sempron] Link Control 03:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200e [Pilot] ServerEngines (SEP1) (rev 02) 04:00.0 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 04:00.1 PCI bridge: NEC Corporation uPD720400 PCI Express - PCI/PCI-X Bridge (rev 06) 09:00.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS (rev 04)

  Read the article

• OOM-Killer, jboss and kernel panic

  - by user32425

  Hi, We are running RedHat 3.4.6(x32) on VMWareEsx3.5(x64) with 6GB RAM. A few java processes(including jboss) are running in the background. The problem is that the java processes consume lots of memory, and sometimes they are killed by the OOM-killer. When OOM-killer is about to act, the free physical memory is very low 100MB-200MB, but the swap is not used (99% free). Sometimes this causes a kernel panic too. So why isn't the swap used? How to investigate this kernel panic? Is using 6GB memory on 32bit Redhat wise? Thanks

  Read the article

• How do I recover from a Linux CentOS 4.6 Operating System Crash

  - by Greg Omebije

  Our x86 Linux server running CentOS4.6 has crashed. The machine boots only to the Grub prompt. We have tried using the "rescue mode" to recover the System, but it hasn't worked. How can we fix this problem, so that the machine boots normally? How can we fix this problem to the point were we can recover our files from the server Our Linux Server Configuration: Dell PowerEdge 1950 Intel Xeon 2 HDD (146GB each) 4GB RAM Hardware and Software raid setup CentOS 4.6 We used Sysrecord to boot the computer: the following are the output of fdisk -l Disk /dev/sda: 293.3 GB, 292326211584 255 heads, 63 sectors/track, 35539 Cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00000080 Device Boot Start End Blocks Id System /dev/sda1 * 1 13 104391 83 Linux /dev/sda2 14 17769 142625070 8e Linux LVM

  Read the article

• HFS for Windows by Paragon BSOD

  - by texmex5

  Installed HFS for Windows 7 yesterday. Did a reboot. Copied some files from my internal drive to external hfs drive. Did another reboot and rebooted to Mac. Mac worked fine. Then yesterday the battery went dead on my mac and the computer switched off. This morning tried to boot into windows but got a BSOD as soon as I moved my mouse in the login screen. BSOD refeers to an error with service HFSPLUS.SYS Now when I try to boot into mac (pressing alt while restarding) the mac drive isn's shown and I can only boot into Windows 7 Safe Mode. Cannot uninstall HFS for Windows the uninstaller in control panel says: "THE WINDOWS INSTALLER SERVICE COULD NOT BE ACCESSED. THIS CAN OCCUR WHEN WINDOWS INSTALLER IS NOT CORRECTLY INSTALLED". SETUP: Intel Core 2 Duo, P8600 @ 2.40GHZ, 4GB RAM, WINDOWS 7 ULTIMATE 32 BIT

  Read the article

• CPU & Memory Usage Log & Performance

  - by wittythotha

  I want to have an idea of the amount of CPU and memory that is being used. I have a website hosted using IIS, and have clients connecting to it. I want to find out the amount of load that the CPU, RAM and the network has when multiple clients connect. I tried out using tools like Fiddler, the inbuilt Resource Manager, and also some other applications I found on the internet. I just want to keep track of all these data in a file, so I can plot out a graph and find out how the CPU, etc. is performing. I read a few other posts, but didn't find anything that solves the problem. Is there good CPU / Memory Logging tool available, just to plot a graph of the usage, etc.? EDIT : I want to know of some tool that can save the performance details in a log file, so that I can use it to plot a graph, etc.

  Read the article

• Mainstream Linux on 1GB HDD

  - by Ariel Nundi

  Hi, I've decided to start learning Linux + Ryby + RoR. The problem is the only personal computer I have is a laptop with 1GB flash card and I can't afford to buy more hardware right now. The laptop has dual core CPU and 2GB of RAM. Can you recommend a Linux distribution I can install? I've tried the netbook version of Ubuntu, but install failed because of lack of space. I'd prefer a more popular distribution, so I can use my skills say on a job. TIA

  Read the article

• How to control admission policy in vmware HA?

  - by John

  Simple question, I have 3 hosts running 4.1 Essentials Plus with vmware HA. I tried to create several virtual machines that filled 90% of each server's memory capacity. I know that vmware has really sophisticated memory management within virtual machines, but I do not understand how the vCenter can allow me even to power on the virtual machines that exceed the critical memory level, when the host failover can be still handled. Is it due to the fact that virtual machines does not use the memory, so that it is still considered as free, so virtual machines can be powered on ? But what would happen if all VMs would be really using the RAM before the host failure - they could not be migrated to other hosts after the failure. The default behaviour in XenServer is that, it automatically calculates the maximum memory level that can be used within the cluster so that the host failure is still protected. Vmware does the same thing ? The admission policy is enabled. Vmware HA enabled.

  Read the article

• Apache hanging with MaxClients is reached

  - by Ash White

  My Apache 2.2 (preform MPM) is hanging when MaxClients is reached, rather than queueing up requests and serving them when child processes become free. When this happens, the web server is totally unresponsive until it is manually restarted. The server stack is Ubuntu 8, MySQL 5, PHP 5. Hardware is Dual Xeons (2.8) with 2GB of RAM. It serves 30,000 - 50,000 pageviews per day. Static images, CSS, and JS are offloaded to a separate server and PHP is cached using eAccelerator. The HTML output of many pages is cached to the filesystem. Relevant Apache directives: KeepAlive On MaxKeepAliveRequests 50 KeepAliveTimeout 2 StartServers 2 MaxClients 150 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 2000

  Read the article

• Dual boot Windows XP 32 bit and Windows 7 64-bit

  - by Santanu Roy

  My system config is AMD phenom-II x2 550 processor, 2x2gb(800fsb)ddr2 zion ram, gigabyte ga-m61pme-s2 motherboard, 160gb sata hdd. Now I am planning to install Windows XP sp3 (32-bit) and Windows 7 (64bit). My first questions are: Is my system enough for the above mentioned two OSes? Which OS one should be installed first on local disk c: drive? I have both XP and vista drivers on separate disks as provided with my motherboard but don't have drivers for win-7, so can I use my vista driver for win-7?

  Read the article

• Disk Redundancy across different server

  - by Mascarpone

  I have 3 servers, all with the same specs: Intel CPU 8 GB RAM Linux or BSD Single 2TB desktop SATA with more than 10K Hours of operation, with only less than 300 GB Used My provider cannot install a second hard drive, but can guarantee me that the drive will be replaced immediately in case of failure, with another equally crappy drive. The likelihood of drive failure is high, and since I can't use RAID, I was thinking about keeping a back up of each machine on all the other machines, so that there are always 2 copies on 2 different drives, plus the original. I would synchronize the drives every hour, with rsync, to guarantee some sort of redundancy, since bandwidth inside the DC is free, so it would be much cheaper than offsite backup. (A daily offiste backup is kept anyhow). What do you think? Any suggestion?

  Read the article

• Can I use a Mac Mini as a web server and database server? What are the pros and cons?

  - by Christopher Altman

  We are a bootstrapped web start up. We have a LAMP web application that we expect relatively low to mid traffic because users need an account to log in. Our current approach is to colocate two servers, a web and mysql database server. We are planning to use Ubuntu Server 9.04. We have shopped around for dedicated servers but the price range from $900 to $1500 per month, therefore we are exploring the colocation approach. We are considering purchasing two Mac Minis (2.0GHz Intel Core 2 Duo 2 Gb RAM) because we are familiar with the machines are the prices are relatively inexpensive. What are the pros and cons of using these 'non-server' grade machines? We would install Ubuntu Sever and attach firewire external hard drives. Any advice on how to set up 'good-and-economic' web/database servers is welcomed.

  Read the article

• Best Linux distro for load-balancers?

  - by Vimvq1987

  I wanted to try HAProxy/Linux Virtual Server like front-end load-balancers, but as far I know, they're Linux-based software. I don't have any experiences with Linux yet. so there're quite many questions to ask: What is the best Linux distro(s) for load-balancing? I plan to use VirtualPC to run some virtual machines. How much RAM is the best for each machine run that distro? I want to simulate a load-balancer with can handle about 100 hits/second, is it possible? Thank you very much!

  Read the article

• I/O Error with PHP5-FPM, ptrace(PEEKDATA) failed

  - by MultiformeIngegno

  I got a lot of these: [NOTICE] child 19214 stopped for tracing [NOTICE] about to trace 19214 [ERROR] ptrace(PEEKDATA) failed: Input/output error (5) [NOTICE] finished trace of 19214 [WARNING] [pool www] child 19208, script 'blahblah.php' executing too slow (30.041419 sec), logging [NOTICE] child 19208 stopped for tracing [NOTICE] about to trace 19208 [ERROR] ptrace(PEEKDATA) failed: Input/output error (5) [NOTICE] finished trace of 19208 [WARNING] [pool www] child 19218, script 'blahblah.php' executing too slow (30.035029 sec), logging And when php reaches max children (at least I presume that's the case) it stops "working"... now I know I can increase max_children (currently set to 9) but there's a way to stop php from "dying"? I'm on a VPS with 1 core and 512 MB of RAM (PHP5-FPM 5.4.4 + APC 3.1.10).

  Read the article

• Lack of Virtual Memory - confusion

  - by Wesley

  Specs ahead of time: AMD Athlon XP 2400+ @ 2.00 GHz / 1 GB PC-3200 DDR RAM / 160 GB IDE HDD / 128 MB GeForce 6200 AGP / FIC AM37 / 350W PSU / Windows XP Pro SP3 So, XP has pop-ups saying that I am low on virtual memory. However, I have a program called SmartRAM (part of Advanced SystemCare by IObit) and it displays CPU & Page File Usage and Free Physical and Virtual Memory. That program shows that I have at least 2000 MB free virtual memory on my machine when the XP pop-ups say that I'm low on virtual memory. First off, would a complete lack of virtual memory cause my computer to freeze? Secondly, how can I solve this lack of virtual memory? (A complete reformat is possible but can't be done immediately...) Thanks in advance.

  Read the article

• Increase application performance on Amazon AWS

  - by Honus Wagner

  I've got a client with an MVC v1 (.NET) application running on a micro instance. On this instance, I've got .NET, IIS 7.5, and MS SQL Server 2008 running to handle the application. The client has reported that it is taking nearly 10 seconds to process each request. Even loading the initial login page takes about that long, then logging in takes that long, etc etc. The currently running instance specs are as follows: 615 MB RAM Intel Xenon CPU E5430 @ 2.66GHz 2.78 GHz 64-Bit Is the memory availability the issue? or is it the processing power? I forsee two options: Change to a larget instance Set up a 2-tier architecture with two micro instances Which of these will give the application better performance? Thanks in advance.

  Read the article

• JVM memory initializazion error after windows update

  - by gianni

  We have three Windows Server 2003 with 2 GB RAM. Server1 tomcat 5.5.25 jvm version SUN 1.6.0_11-b03 Server2 tomcat 5.5.25 jvm version SUN 1.6.0_14-b08 Server3 tomcat 6.0.18 jvm version SUN 1.6.0_14-b08 For the three servers JVM parameters are: -XX:MaxPermSize=256m -Dcatalina.base=C:\Programmi\Apache Group\apache-tomcat-5.5.25 -Dcatalina.home=C:\Programmi\Apache Group\apache-tomcat-5.5.25 -Djava.endorsed.dirs=C:\Programmi\Apache Group\apache-tomcat-5.5.25\common\endorsed -Djava.io.tmpdir=C:\Programmi\Apache Group\apache-tomcat-5.5.25\temp vfprintf -Xms512m -Xmx1024m For some months everithing worked fine. Last friday we installed some windows updates. After the reboot tomcat doesnt start with error: Error occurred during initialization of VM Could not reserve enough space for object heap We reduced the parameter -Xmx1024m to -Xmx768m and now tomcat starts. But we need greater max heap size What happened to our servers ? Thanks in advance.

  Read the article

• PSU requirement question for my PC setup.

  - by user69474

  I understand that sometimes there may be a situation where the PSU is way more than required but in this case of mine, I'm not too sure. Sometimes when I play games, my computer will crash and restarts itself, 10 mins into the game. Once I received a message that says something like the power is overheating or something like that. Ok, so I have a 500W PSU. I have: 1x Internal DVD writer 1x SATA 250GB HD 1x Nvidia 8500 GT 2GB RAM. As I'm planning to get an additional 250GB SATA HD, I wonder if I need to increase my PSU as well -- in full knowledge of the previous crashes experienced before. Should I upgrade my PSU to 650W perhaps, or is that excessive?

  Read the article

• KVM CLI install for CentOS 6.3 defaults to Minimal Install

  - by i.h4d35

  So I now I've installed KVM (and its associated tools and packages- libvirt, VMM etc.). On the GUI (i.e using the VMM), installation works as its supposed to. However, when I try to create a VM using the command line interface, the OS (I am working with CentOS 6.3) defaults to a Minimal Install instead of giving me options to choose from at the time of installation. I am trying to install using the following command: virt-install \ --connect qemu:///system \ --virt-type kvm --name testVM2 \ --ram 512 --disk path=/var/lib/libvirt/images/testVM2.img,size=8 --vnc \ --cdrom /media/db18de8e-0853-49fb-80de-5c794d58a46f/CentOS-6.3- x86_64-bin-DVD1.iso \ --network network=default Specifying the OS-type or the OS-variant parameters doesn't make a difference. Is there something that I am missing out on or some other parameter that I must specify? Thanks in advance.

  Read the article

< Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >