Search Results

Search found 31586 results on 1264 pages for 'custom result'.

Page 1041/1264 | < Previous Page | 1037 1038 1039 1040 1041 1042 1043 1044 1045 1046 1047 1048  | Next Page >

• cannot connect to vpn server (error 721)

  - by callmeblessed

  Hi I got 2 internet connections in my computer. One is using 3.5G HSDPA modem (vodafone huawei e220) and the other using mobile phone (cdma zte c261). Both are using different ISP and i have both. at the moment, i can connect to my office vpn using the HSDPA modem one. But when i tried to use cdma modem (dial up - mobile phone modem), i am just able to get "verifying username and password" and then after a few minutes it display error : Error 721 The Remote Computer didn't respond. I tried to ping into my office ip address, it got good result but still cannot connect to the vpn. I tried to turn off all my firewall (i'm using commodo) and has no response as well. In my cdma mobile phone modem Network connections I tried to allow iNternet connection sharing as well ... and turn on all Internet Protocol TCP/IP, File & Printer Sharing & Client for microsoft networks. But all of my effort has no effect. How to fix this problem ? note: my office using windows vpn as well. thank you .

  Read the article

• NTBackup (on WS2k3) fails to backup remote server (WS2k8R2) with " Error: is not a valid drive, or you do not have access."

  - by Mark A

  We run an NTBackup job on a Windows Server 2003 R2 SP2 with all updates (as of Q4-2011). It works well backing up two WS2k3 servers as well as the backup server itself. However, we have been unable to successfully back up our Windows Server 2008 R2 machine ("G5-01"). It often runs for about 2GB worth of backup and then dies out with one of the below error messages. It should be more like 20GB for the full server. We have tried using the admin share (C$), an explicitly shared drive share, UNC and mapped drives. The result is the same each time, the only thing that varies is the amount of stuff backed up before it chokes. We've also run NTBbackup from the UI interface, from the command line and as a scheduled task. We are backing up to 400/800GB tapes and they have plenty of space available on them (blank media). Error: \\G5-01\c is not a valid drive, or you do not have access. Error: \\G5-01\c$ is not a valid drive, or you do not have access. Error: Y: is not a valid drive, or you do not have access. Error: Could not access or create backup catalog files. Verify that you have full access to the working folder and there is disk space available. The job is run as Administrator and we have no problems logging onto the server and transferring files. The Event Log on the WS2k8 is not much help, as it has success audits for each login. All of the hardware involved (HP DL360 G3, HP LTO Ultrium 3, Adaptec 39320A) has the latest supported drivers. We've seemingly tried a bunch of different options but are wondering where to look next to resolve the backup issue. We've been super happy with our reliable schedule task for years but this one is stumping us!

  Read the article

• VMWare web UI intermittent access on CentOS

  - by PeteWilliams

  I've got a CentOS 5.2 server that I'm trying to get set up as a development environment. As part of this, I planned to install VMWare Server 2 and set up several virtual development servers. I've got as far as installing VMWare Server 2 but access to the remote control panel is only working intermittently. If I access it through Firefox at https://127.0.0.1:8333/ui/# it usually says either: "Connection intterupted: connection was reset before the page loaded" Or "Firefox can't establish a connection to the server at 127.0.0.1" But every now and then it lets me in and I'll manage a few clicks in the web UI before it kicks me out with the following error: "The server could not complete a request (HTTP 0 ). The server encountered an unexpected condition that prevented it from fulfilling the request. If this problem persists, please contact your system administrator." I've done all the updates available in CentOS except one OpenOffice one that is causing a conflict, and I re-ran wmware-config.pl after updating the kernel. Though I went with all the defaults as I don't really know what I'm doing! I've since rebooted and nothing changed. I've also tried accessing the control panel remotely from another machine in the network and the results are the same. Does anyone have any ideas what might be causing this and how I can resolve it? I'm afraid I'm a developer playing at sys-admin, so I may be missing something obvious! Many thanks Pete Update I have now reinstalled both the operating system and VMWare and I'm still getting the same issue. I wonder if it's a result of the settings I'm putting in on the config.pl script..?

  Read the article

• Syncing two sheets, while being able to hide different data

  - by Joshua

  I'm pretty new to excel- so please bear with me. I have created a spreadsheet to organize gear by serial numbers and by who has it. This list is getting updated multiple times daily as gear shuffles regularly. I have gear that is assigned and unassigned. On the main sheet I have all the data, the way I want it to be organized. What I'm trying to do is duplicate this sheet, so that both sheets automatically keep the same data at all times, but on the first sheet I can hide all the unassigned gear, and view only the assigned gear, and then be able to narrow it down in groups using the hide function heavily. On the second sheet I want to be able to hide all of the assigned gear, and all the columns of gear that have no unassigned gear. End result will be that as gear is moved between individuals or is unassigned entirely, I make that adjustment on one sheet and the data stays the same on both, but the way I view that same sheet is different on both. If I'm making no sense just let me know and I'll try to explain again more clearly. Thanks

  Read the article

• Snow Leopard takes a long time to connect to Windows/Samba server

  - by hood

  We run a very heterogeneous network here: There is some XP, Vista, 7, Leopard, Snow Leopard clients, and Windows 2003 (one remaining legacy app), 2008, and Linux servers. The main file server runs Ubuntu Linux and has been added to the Windows Domain and has been used for many years; SBS 2008 is the PDC (the 2003 and 2008 are on the domain also). In Leopard there were no problems at all authenticating to the file servers. We've upgraded one of the Leopard iMacs to Snow Leopard, though the same problem occurs in a new MBP which came with the newer OS as well as a clean install on another iMac. It does not matter whether connected through wired or wireless. In the Finder when clicking on the server - whether on first boot or after it is connected - it will display "Connecting..." for up to a few minutes before either generally working (if username/password in keychain) or displaying "Connection Failed" - at which time clicking "Connect As" and typing in the username/password will take some more time and eventually work. Sometimes it will display "Connecting..." indefinitely. (I've left it as long as 15 minutes before trying something else) Accessing shares on the the 2003 and SBS servers have the problem (so I don't think it's a Samba server issue). The Server 2008 Standard is connecting instantly at the moment. Accessing the share through an alias/stacks doesn't have this problem. Leopard and Windows clients still have no problem. I've searched Google but hasn't yielded any working result. How do I get rid of this delay?

  Read the article

• Replace Linux Boot-Drive | ext3 to btrfs

  - by bardiir

  I've got a headless server running Debian Linux currently. Linux vault 3.2.0-3-686-pae #1 SMP Mon Jul 23 03:50:34 UTC 2012 i686 GNU/Linux The root filesystem is located on an ext3 partition on the main harddrive. My data is located on multiple harddrives that are bundled to a storage pool running with btrfs. UUID=072a7fce-bfea-46fa-923f-4fb0827ae428 / ext3 errors=remount-ro 0 1 UUID=b50965f1-a2e1-443f-876f-578b5f93cbf1 none swap sw 0 0 UUID=881e3ad9-31c4-4296-ae60-eae6c98ea45f none swap sw 0 0 UUID=30d8ae34-e2f0-44b4-bbcc-22d761a128f6 /data btrfs defaults,compress,autodefrag 0 0 What I'd like to do is to place / into the btrfs pool too. The ideal solution would provide the flexibility to boot from any disk in the system alike, so if the main drive fails I'd just need to swap another one into the main slot and it would be bootable like the main one. My main problem is, everything I do needs to result in a bootable system that is open to ssh logins via network as this server is 100% headless so there is no possibility to boot it from a live cd or anything like that. So I'd like to be extra sure everything works out fine :) How would I best go about this? Can anybody hint me to guides or whip something up for these tasks? Anything I forgot to think about? Copy root-data into btrfs pool, adjust mountpoints,... Adjust GRUB to boot from btrfs pool UUID or the local device where GRUB is installed Sync GRUB to all harddrives so every drive is equally bootable (is this even possible without destroying the btrfs partitions on the drives or would I need to disconnect the drives, install grub on them and then connect them back with a slightly smaller partition?)

  Read the article

• How do you set max execution time of PHP's CLI component?

  - by cwd

  How do you set max execution time of PHP's CLI component? I have a CLI script that has gone into a infinite loop and I'm not sure how to kill it without restarting. I used quicksilver to launch it, so I can't press control+c at the command line. I tried running ps -A (show all processes) but php is not showing up in that list, so perhaps it has timed out on it's own - but how do you manually set the time limit? I tried to find information about where I should set the max_execution_time setting, I'm used to setting this for the version of PHP that runs with apache, but I have no idea where to set it for the version of PHP that lives in /usr/bin. I did see the follow quote, which does seem to be accurate (see screenshot below), but having an unlimited execution time doesn't seem like a good idea. Keep in mind that for CLI SAPI max_execution_time is hardcoded to 0. So it seems to be changed by ini_set or set_time_limit but it isn't, actually. The only references I've found to this strange decision are deep in bugtracker (http://bugs.php.net/37306) and in php.ini (comments for 'max_execution_time' directive). (via http://php.net/manual/en/function.set-time-limit.php) ini_set('max_execution_time') has no effect. I also tried the same thing and go the same result with set_time_limit(7).

  Read the article

• TLS_REQCERT and PHP with LDAPS

  - by John

  Problem: Secure LDAP queries via command-line and PHP to an AD domain controller with a self-signed certificate. Background: I am working on a project where I need to enable LDAP look-ups from a PHP web application to a MS AD domain controller that is using a self-signed certificate. This self-signed certificate is also using a domain name that is not a FQDN - think of something like people.campus as the domain name. The web application would take the user's credentials and pass them on to the AD domain controller to verify if the credntials are a match or not. This seems simple, but I am having problems trying to get PHP and the self-signed certificate to work. Some people have suggested that I changed the TLS_REQCERT variable from "request" to "never" within the OpenLDAP configuration. I am concerned that this might have larger implications such as a man-in-the-middle attack and I am not comfortable changing this setting to never. I have also read some places online where one can take a certificate and place it as a trusted source within the openldap configuration file. I am curious if that is something that I could do for the situation that I have? Can I, from the command line, obtain the self-signed certificate that the AD domain controller is using, save it to a file, and then have openldap use that file for the trust that it needs so that I do not need to adjust the variable from request to never? I do not have access to the AD domain controller and as a result cannot export the certificate. If there is a way to obtain the certificate from the command line, what commands do I need to use? Is there an alternate method of handling this issue that would be better in the long run? I have some CentOS servers and some Ubuntu servers that I am working with to try and get this going on. Thanks in advance for your help and ideas.

  Read the article

• How to reject messages to unknown user in sendmail cooperating with MS-Exchange?

  - by user71061

  Hi! I have an MS Exchange 2003 configured as a mail server for an organization. As this server is located in this organization internal network and I don't want to expose it directly over internet, I have second server - linux box with sendmail - configured as intelligent relay (it accept all messages from internet addressed to @my_domain, and forward it to internal Exchange serwer, and accepts all messages from this internal Exchange server and forward it over internet). This configuration work's fine, but I want to eliminate messages addressed to not exiting users as early as possible. Good solution could be Enabling on Exchange server function of filtering recipients together with "tar pitting", but in my case this dosn't solve problem, because before any message reach my Exchange server (which could eventually reject it), it has to be already accepted by sendmail server, sitting in front of this Exchange server. So, I want to configure my sendmail server in such a way, that during initial SMTP conversation it could query somehow my Exchange server checking whether recipient address is valid or not, and based on result of this query, accept or reject (possibly with some delay) incoming message in a very early phase. In fact, I have already solved this issue by writing my own, simple sendmail milter program which checks recipient address against text file with list of valid addresses. But this solution is not satisfying me any longer, because it requires frequent updates of this file, and due to lack of time/motivation/programming skills, I don't want to cope further with my source code, adding to it functionality of querying my Exchange server. Maybe I can achieve desired effect by configuring any component of already available linux software. Any ideas?

  Read the article

• SSL Handshake negotiation on Nginx terribly slow

  - by Paras Chopra

  I am using Nginx as a proxy to 4 apache instances. My problem is that SSL negotiation takes a lot of time (600 ms). See this as an example: http://www.webpagetest.org/result/101020_8JXS/1/details/ Here is my Nginx Conf: user www-data; worker_processes 4; events { worker_connections 2048; use epoll; } http { include /etc/nginx/mime.types; default_type application/octet-stream; access_log /var/log/nginx/access.log; sendfile on; keepalive_timeout 0; tcp_nodelay on; gzip on; gzip_proxied any; server_names_hash_bucket_size 128; } upstream abc { server 1.1.1.1 weight=1; server 1.1.1.2 weight=1; server 1.1.1.3 weight=1; } server { listen 443; server_name blah; keepalive_timeout 5; ssl on; ssl_certificate /blah.crt; ssl_certificate_key /blah.key; ssl_session_cache shared:SSL:10m; ssl_session_timeout 5m; ssl_protocols SSLv2 SSLv3 TLSv1; ssl_ciphers RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP; ssl_prefer_server_ciphers on; location / { proxy_pass http://abc; proxy_set_header X-Real-IP $remote_addr; proxy_set_header Host $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } } The machine is a VPS on Linode with 1 G of RAM. Can anyone please tell why SSL Hand shake is taking ages?

  Read the article

• Advice on Computer Specs for overall development/general use machine

  - by Ender

  At the moment I am restricted to a laptop with 512MB of RAM, a 120GB HDD and a 1.5GHz Intel processor for all my development and general browsing needs, and as you can probably tell using it for anything modern is a painful experience. As a result I've decided to buy myself a new desktop computer, one that will stand the test of time and one that can be upgraded easily. Rather than build the machine myself I've decided to go through Dell as I've had good experiences with them when purchasing computers for my family. I've had my eye on this as it's got a good amount of RAM, has a decent-rated processor and isn't priced too badly. http://www1.euro.dell.com/uk/en/home/Desktops/inspiron-580/pd.aspx?refid=inspiron-580&s=dhs&cs=ukepp1&~oid=uk~en~20211~inspiron-580_d005827~~ Intel® Core™ i5 Processor 750 (2.66GHz, 8MB) Genuine Windows® 7 Home Premium 64bit - English Display Not Included ATI Radeon™ HD 5450 1GB DDR3 graphics 6144MB Dual Channel DDR3 [3x2048] Memory 1TB (7200rpm) SATA Hard Drive DVD +/- RW Drive (read/write CD & DVD) with DVD Burn software 1 year of coverage included with your PC McAfee® Security Centre - 15 Month Protection - English After the pain of using a slow laptop for all this time the main thing I want is speed. I may look to play a couple of basic games on it, nothing too powerful. Obviously I'll be doing some development on it too so it'll have to be able to handle the latest IDE's and Database tools like SQL Server pretty quickly. Finally, should I ever need to improve it I'd like to be able to add more RAM and change some of the parts. I wouldn't have thought this would be a problem but a few people I've spoken to have said that the amount of RAM the motherboard can handle isn't that great. Is this true? How long can I expect to be using this computer before it's too slow? Thanks in advance for the help.

  Read the article

• System occasionally hangs boot process with SLES 11

  - by ThaMe90

  I have several (new) systems on which I had to install SLES11 on. However, after a few (though not every) reboots, the system hangs during the boot sequence. It will only continue after I physically press a key on the keyboard. From what I've found in the dmesg log from a failed boot is the following: [ 22.170276] sd 0:0:0:0: [sda] Mode Sense: b7 00 00 08 [ 22.171155] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 22.182760] sda: sda1 sda2 sda3 [ 22.383424] sd 0:0:0:0: [sda] Attached SCSI disk [ 22.545372] PM: Marking nosave pages: 000000000009a000 - 0000000000100000 [ 22.545377] PM: Marking nosave pages: 00000000bf780000 - 0000000100000000 [ 22.546217] PM: Basic memory bitmaps created [ 22.590380] PM: Basic memory bitmaps freed [ 22.596284] PM: Starting manual resume from disk [ 22.602319] PM: Resume from partition 8:1 [ 22.602321] PM: Checking hibernation image. [ 22.602479] PM: Error -22 checking image file [ 22.602481] PM: Resume from disk failed. [ 22.718727] kjournald starting. Commit interval 15 seconds [ 22.718960] EXT3-fs (sda3): using internal journal [ 22.718964] EXT3-fs (sda3): mounted filesystem with ordered data mode [ 1555.644404] udevd version 128 started [ 1555.697664] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 1555.707961] ACPI: Power Button [PWRB] I've looked around the internet for the PM: Resume from disk failed. message, but this seems to only be important when restoring the system after a hybernate, i.e. restore from the hdd. But this is not my situation. I only get this after a reboot, as I said before. The timestamp [ 1555.xxxxxx] is only the result of me pressing a key on the keyboard. Any suggestions on how to proceed? As I am getting stuck on this issue.

  Read the article

• High data on recv-q buffer and thread lock on java.io.BufferedInputStream in linux

  - by Sagar Patel

  We have a java application running on linux (ubuntu server). We have been facing high recv-q problem since quite some time. Application gets hang and does not read data from socket every few hours. In thread dump, we have found below stack trace. "Receiver-146" daemon prio=10 tid=0x00007fb3fc010000 nid=0x7642 runnable [0x00007fb5906c5000] java.lang.Thread.State: RUNNABLE at java.net.SocketInputStream. socketRead0(Native Method) at java.net.SocketInputStream.read(SocketInputStream.java:150) at java.net.SocketInputStream.read(SocketInputStream.java:121) at java.io.BufferedInputStream.fill(BufferedInputStream.java:235) at java.io.BufferedInputStream.read1(BufferedInputStream.java:275) at java.io.BufferedInputStream.read(BufferedInputStream.java:334) - locked <0x00000007688f1ff0> (a java.io.BufferedInputStream) at org.smpp.TCPIPConnection.receive(TCPIPConnection.java:413) at org.smpp.ReceiverBase.receivePDUFromConnection(ReceiverBase.java:197) at org.smpp.Receiver.receiveAsync(Receiver.java:351) at org.smpp.ReceiverBase.process(ReceiverBase.java:96) at org.smpp.util.ProcessingThread.run(ProcessingThread.java:199) at java.lang.Thread.run(Thread.java:722) We are not able to trace the exact reason behind this? Kindly help. We are using 16 core machine and load on the system is around 30-40 at the time of issue. We use command ss dst <ip> to find out recv-q. Recently we have been facing issues with recv-q size getting hung, were in receive buffer gets stuck at some point of time. But recvQ size is not decreasing and as a result we are losing a lot of hits from the other side, our application is not accepting any data.

  Read the article

• Windows 7 ICS client web failure

  - by n8wrl

  I have several windows 7 PC's connected on a LAN via a hub. One has a Verizon 3G connection and works great. I have internet connection sharing enabled on it, which automagically set the LAN connection to 192.168.137.1 and enabled DHCP. I am trying to get the client PC's working one at a time. The others are off. The client is able to: Get an IP via DHCP with correct settings. Ping any web address I can throw at it, so DNS and routing are working. Windows update works. But web sites hang in IE. All but google.com! I type www.msn.com, microsoft.com, amazon.com, etc. etc. All ping via a cmd window but IE just hangs - it says web site found but the green progress bar just slowly creeps and no content displays. www.google.com comes up even after clearing browser and dns cache. I am pulling my hair out - what am I missing? EDIT: After some more gyrations with a router I'm back to ICS. Same symptoms, only now I have an answer to Andrew's question, YES I can do Google searches but clicking on any of the result links hangs! Let one sit for half an hour with no timeout or error.

  Read the article

• Imagemagick convert with resample option

  - by coneybeare

  I am creating thumbnails from much larger images and have been using this command successfully for some time: convert FILE -resize "64x" -crop "64x64+0+16" +repage -strip OUTFILE I also do some other processing that is not relevant to the question. I realized that this does not adjust the resolution at all, so if I use a 300dpi image, it ends up displaying really small on some devices. I want to resample it to 72x72 so I have been trying with this command: convert FILE -resize "64x" -crop "64x64+0+16" +repage -strip -resample 72x72 OUTFILE And expected the 64x64 image at 300dpi to be resampled to a 64x64 image at 72dpi, but instead, I am getting a very funny size and density. Here is "identify" output for the original and post-processed file WITHOUT the resample: coneybeare $ convert "aa.jpg" -crop "64x64+0+16" +repage -strip "aa.png" coneybeare $ for image in `find . -type f`; do identify $image; identify -verbose $image | egrep "^ Resolution"; done ./aa.jpg JPEG 1130x1695 1130x1695+0+0 8-bit DirectClass 1.492MiB 0.000u 0:00.000 Resolution: 300x300 ./aa.png PNG 64x64 64x64+0+0 8-bit DirectClass 7.46KiB 0.000u 0:00.000 Resolution: 118.11x118.11 And here is the "identify output for the command WITH the resample: coneybeare $ convert "aa.jpg" -crop "64x64+0+16" +repage -strip -resample 72x72 "aa.png" coneybeare $ for image in `find . -type f`; do identify $image; identify -verbose $image | egrep "^ Resolution"; done ./aa.jpg JPEG 1130x1695 1130x1695+0+0 8-bit DirectClass 1.492MiB 0.000u 0:00.000 Resolution: 300x300 ./aa.png PNG 15x15 15x15+0+0 8-bit DirectClass 901b 0.000u 0:00.000 Resolution: 28.34x28.34 So, the question is: What am I doing wrong and how can I fix it so the end result is a 64x64 cropped thumbnail image at 72dpi?

  Read the article

• Ubuntu 13.10 - How to disable LVM and cryptsetup? cryptsetup: evms_activate is not available

  - by NeverEndingQueue

  I am trying to remove whole drive encryption from my Ubuntu installation. I've run Ubuntu from Live CD, mounted crypt partition and copied it to another partition /dev/sda3. sudo cryptsetup luksOpen /dev/sda5 crypt1 sudo dd if=/dev/ubuntu-vg/root of=/dev/sda3 bs=1M After that I've run boot-repair: https://help.ubuntu.com/community/Boot-Repair Added entry to /etc/fstab: UUID=<uuid> / ext4 errors=remount-ro 0 1 Of course I've replaced with blkid result of my /dev/sda3. I've also deleted overlayfs and tmpfs lines from /etc/fstab. (I've just compared it to content of /etc/fstab in non-encrypted Ubuntu installation and could not find overlayfs and tmpfs). I've chrooted from LiveCD into my system and rebuilt initramfs: http://blog.leenix.co.uk/2012/07/evmsactivate-is-not-available-on-boot.html I've also removed cryptsetup using apt-get remove. Basically I can easily mount my system partition from Live CD (without setting up the encryption and LVM stuff), but can not boot from it. Instead I see: cryptsetup: evms_activate is not available When I've chosen the Recovery mode I've seen this: Begin: Mounting root file system ... Begin: Running /script/local-top ... Reading all physical volumes. This may take a while ... No volume groups found cryptsetup: evms_activate is not available Begin: Waiting for encrytpted source device ... My /etc/crypttab is empty. I am pretty sure that system tries to find encrypted partition, search for LVMs etc. Do you have ideas what could be the problem or how can I fix it? Thanks

  Read the article

• VirtualBox how to merge arbitrary snapshot into base vdi

  - by jmathew

  I botched a transfer of a VM from one harddisk to the other. Now I'm left with the base vdi and a whole bunch of snapshots. My steps Copied old VM directory over to new HDD Deleted old VM and added new VM using using Machine-add and providing the old XML file Couldn't add base vdi file due to conflict so changed the UUID of base vdi with VBOXMANGE.EXE internalcommands sethduuid Attempt to rollback to a snapshot, but it seems the VM is looking for the snapshots on the old HDD (which is formatted and gone) This is the error (networked is the name): Failed to restore the snapshot networked of the virtual machine lfs. Could not open the medium 'H:\vm\ft.vdi'. VD: error VERR_PATH_NOT_FOUND opening image file 'H:\vm\ft.vdi' (VERR_PATH_NOT_FOUND). Result Code: E_FAIL (0x80004005) Component: Medium Interface: IMedium {53f9cc0c-e0fd-40a5-a404-a7a5272082cd} The old HDD was drive H: the new one is drive N: How can I modify the snapshots/VM to look in N:\vm\ft.vdi for the base vdi? I've already set the default settings in VirtualBox in general (default vm/vm snapshot location). Or if not that how can I merge the old snap shot with the base vdi given that the only things that have changed is the base vdi's UUID? Thanks

  Read the article

• Reusing slot numbers in Linux software RAID arrays

  - by thkala

  When a hard disk drive in one of my Linux machines failed, I took the opportunity to migrate from RAID5 to a 6-disk software RAID6 array. At the time of the migration I did not have all 6 drives - more specifically the fourth and fifth (slots 3 and 4) drives were already in use in the originating array, so I created the RAID6 array with a couple of missing devices. I now need to add those drives in those empty slots. Using mdadm --add does result in a proper RAID6 configuration, with one glitch - the new drives are placed in new slots, which results in this /proc/mdstat snippet: ... md0 : active raid6 sde1[7] sdd1[6] sda1[0] sdf1[5] sdc1[2] sdb1[1] 25185536 blocks super 1.0 level 6, 64k chunk, algorithm 2 [6/6] [UUUUUU] ... mdadm -E verifies that the actual slot numbers in the device superblocks are correct, yet the numbers shown in /proc/mdstat are still weird. I would like to fix this glitch, both to satisfy my inner perfectionist and to avoid any potential sources of future confusion in a crisis. Is there a way to specify which slot a new device should occupy in a RAID array? UPDATE: I have verified that the slot number persists in the component device superblock. For the version 1.0 superblocks that I am using that would be the dev_number field as defined in include/linux/raid/md_p.h of the Linux kernel source. I am now considering direct modification of said field to change the slot number - I don't suppose there is some standard way to manipulate the RAID superblock?

  Read the article

• Wireless signal changes from strong to weak after connecting

  - by gibberish

  Router (primary AP) is a WRVS4400N, WAP (signal booster) is a WAP4410N. Problem: User is physically located within ten feet of WAP (200 feet from main wireless router). Signal is at 5 bars as user connects to wireless network. Within seconds, signal is at or below two bars and connection is poor. Background: Trying to solve problem of weak wireless signal in back offices. Desired result is for client laptops to automatically switch to the stronger signal. WAP is connected to network via Ethernet cable. WAP is set to AP mode (instead of Wireless Repeater mode) WAP does appear to boost signal. Using Windows 7 sys tray Connect To A Network applet, can observe signal boost as laptop approaches the WAP. Above-described problem happens to users located near or beyond the WAP. It does not happen to users in close proximity to the router. Secondary Question: If using WAP in AP Mode, do WAP and Router (primary AP) need to be on the same channel?

  Read the article

• Streaming music throughout the house on a budget?

  - by greggannicott

  I was wondering whether anyone knew of a way to stream music throughout a house on a budget? I want to avoid spending any money on this (eg. I don't want to buy a d-link style device). It would be ideal if I could use my existing hardware and some open source software. I have three old(ish) PCs knocking around. I'm happy to stick either Windows or Linux on them. They can all be hooked up to speakers. The ideal solution would result in: the same audio being heard from every device (eg. when you hear a beat on one device, you'd hear it at the exact same time on another (so you don't get any echo)) I'd be able to control the source application (eg. the songs lined up) with my iPhone. I realise I'm being cheeky with those two wishes - but you never know your luck. Am I asking for too much, or is there a piece of software/protocol out there with this purpose in mind? I've been searching for sometime now, but haven't had any joy. Thanks in advance.

  Read the article

• VPN Connection Causes Internal LAN Connection Loss with Server

  - by sleepisfortheweak

  I've tried configuring basic PPTP VPN at my small business using a number of different tutorials. As far as I can tell, the actual VPN connection worked fine, but upon connecting a client, the Server 'disappears' from the internal LAN. The RRAS service must be stopped before the connection is restored. My Setup: The network is simply a DSL Gateway/Router to the outside functioning as NAT/Firewall/DHCP. The server is a Win Server 2008 machine at fixed IP 192.168.1.200. The server has 1 NIC, so I used the 'custom' option when configuring RRAS. The RRAS settings should be default except that I've disabled ports for connection types I'm not using and reduced PPTP ports to 10. I've also created an address pool and disabled DHCP packet forwarding. The server only functions as a File Share and now a VPN Server. Local LAN computers all have mapped network shares to the server authenticated based on Local User/Group setup on the server. The Problem: The moment a client connects through VPN, the server 'disappears' from the local network. All mapped drives disconnect and there is no response to a ping 192.168.1.200. Even if the client disconnects, the server does not re-appear at that address until the RRAS service is stopped. I've Tried: Using an Address Pool inside and outside the local subnet. Using DCHP Relay Checking Inbound/Outbound filters (none enabled) The fact that nothing I've tried has had any effect, and that I can connect and successfully obtain an IP tells me that it's something more fundamental I'm missing. My gut tells me that it's something to do with the second IP address added by the VPN client somehow taking over the interface or traffic from the local LAN accidently getting routed to the VPN client instead of handled at the server once RRAS has become 'active' when a client connects. Hopefully this may be obvious to someone with real IT experience. I've been doing this a while and almost never been stumped. I'm starting to think it might actually be something tricky since my setup is pretty basic yet refuses to work. I'll be happy to include more info if this doesn't ring any bells right away for anyone. Thanks

  Read the article

• Bandwidth monitoring with iptables for non-router machine

  - by user1591276

  I came across this tutorial here that describes how to monitor bandwidth using iptables. I wanted to adapt it for a non-router machine, so I want to know how much data is going in/coming out and not passing through. Here are the rules I added: iptables -N ETH0_IN iptables -N ETH0_OUT iptables -I INPUT -i eth0 -j ETH0_IN iptables -I OUTPUT -o eth0 -j ETH0_OUT And here is a sample of the output: user@host:/tmp$ sudo iptables -x -vL -n Chain INPUT (policy ACCEPT 1549 packets, 225723 bytes) pkts bytes target prot opt in out source destination 199 54168 ETH0_IN all -- eth0 * 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 1417 packets, 178128 bytes) pkts bytes target prot opt in out source destination 201 19597 ETH0_OUT all -- * eth0 0.0.0.0/0 0.0.0.0/0 Chain ETH0_IN (1 references) pkts bytes target prot opt in out source destination Chain ETH0_OUT (1 references) pkts bytes target prot opt in out source destination As seen above, there are no packet and byte values for ETH0_IN and ETH0_OUT, which is not the same result in the tutorial I referenced. Is there a mistake that I made somewhere? Thanks for your time.

  Read the article

• How can I setup BluePill to Monitor a Rails App Running via Passenger (mod_rails)

  - by Jim Jeffers

  I recently launched a site running phusion passenger. Unfortunately, the site went down due to a frozen thread. I was able to save the server by doing kill -9 to the specific PID. Still though, I thought passenger was able to manage this automatically. I have a server with 1GB of memory running one rails app with passenger allotted up to 7 instances. However, when I came to discover the site went down I found that passenger had spawned 6 instances with one of them using up over 800mb of memory causing the server to swap. As a result I am hoping to setup something like bluepill on the server but I'm slightly confused as to how you go about doing it. Mainly because bluepill expects to start/stop the processes it's monitoring. However, in our case, passenger already restarts processes for us so we only need to monitor the pids of passengers instances and kill them once they've gotten too large. Has anyone here setup BluePill to monitor a rails app running under phusion's passenger? Any insight would be useful.

  Read the article

• Linux usd disk just create sg device

  - by MTilsted

  I have a Corsair R60 ssd disk which is a disk with both sata and usb connectors. But the usb thing seems to be a bit non-standard, or maybe its just my fedora linux. When I insert the disk using a usb cabel to a running Fedora 14 linux system, a device called /dev/sg3 is added but that is all. No new /dev/sd* device is created so I can't mount the disk. If I look at cat /proc/scsi/sg/device_strs I get ATA Hitachi HTS54321 FB2O HL-DT-ST DVDRAM GSA-T50N RP05 Seagate Desktop 0130 Corsair CSSD-R60GB2 So the disk is there. (The last entry) but my linux will for some reason not see it as a usb hard disk. When I insert other usb disks they work fine. It is only this specific disk which causes problems. I have tried on 3 different computers with the same result. A hint to the problem may be that if I add the disk to a windows system(With usb) the disk is called "A fixed disk" and not a portable disk as expected. The disk works fine with linux If i connect it with the sata cabel, but I would really like to have it working with usb too. (To mount it on computers without sata).

  Read the article

• What is the reason for this DNSSEC validation failure of dnsviz.net?

  - by grifferz

  On trying to resolve dnsviz.net from a host using an Unbound resolver that is configured to use DNSSEC validation, the result is "no servers could be reached": $ dig -t soa dnsviz.net ; <<>> DiG 9.6-ESV-R4 <<>> -t soa dnsviz.net ;; global options: +cmd ;; connection timed out; no servers could be reached Nothing is logged by Unbound to suggest why this is the case. Here is the /etc/unbound/unbound.conf: server: verbosity: 1 interface: 192.168.0.8 interface: 127.0.0.1 interface: ::0 access-control: 0.0.0.0/0 refuse access-control: ::0/0 refuse access-control: 127.0.0.0/8 allow_snoop access-control: 192.168.0.0/16 allow_snoop chroot: "" auto-trust-anchor-file: "/etc/unbound/root.key" val-log-level: 2 python: remote-control: control-enable: yes If I add: module-config: "iterator" (thus disabling DNSSEC validation) then I am able to resolve this host normally. The domain and its DNSSEC check out fine according to http://dnscheck.iis.se/ so there must be something wrong with my resolver configuration. What is it and how do I go about debugging that?

  Read the article

< Previous Page | 1037 1038 1039 1040 1041 1042 1043 1044 1045 1046 1047 1048  | Next Page >