Search Results

Search found 6931 results on 278 pages for 'almost surely'.

Page 105/278 | < Previous Page | 101 102 103 104 105 106 107 108 109 110 111 112  | Next Page >

• How to troubleshoot slow powerconnect 62xx management interface

  - by Hannes

  Our Dell Powerconnect 62xx switches have a very high packetloss on the management interface. I presume this is caused by a new appliance which uses multicast for communication but I am not sure. Our network setup is following: servers a - Dell PC6248 | servers b - Dell PC6248 |- juniper core router servers c - Dell PC6248 | What we see is that the multicast traffic arrives at all servers (but only the servers b use the multicast) and I fear that this multicast traffic floods the switch management interface. The switches' management interfaces are reachable via vlan101, all other traffic is sent over other vlans. When I tcpdump on one of the 2 servers with a vlan 101 ip address, I only get a few arp requests but almost nothing. When I try to ping between these 2 servers, it works like a charm. I would like to know what a good way is to troubleshoot this problem and maybe help me understand what is going wrong on that subnet.

  Read the article

• Apache HTTP Server+Tomcat: Which file generates mod_jk.conf, how to modify generated stuff, and how does httpd reach it?

  - by Sk8erPeter

  I'm using XAMPP with Apache HTTP Server and Tomcat Add-On installed. There's a default mod_jk.conf which is generated by Tomcat when starting it. But which file generates this mod_jk.conf file? How can I modify default values? By default, it looks like this: pastebin - mod_jk.conf. How does Apache HTTP Server reach this file? I can't see any reference to this file when looking into httpd.conf. When I put a VirtualHost in my httpd.conf file, and I put the line JkMount /* ajp13 into it, Apache HTTP Server service can't start (causes a 7024 event id error in Event Viewer (with error code 1, but nothing specific), but puts no error messages into error.log. The VirtualHost looks like this: pastebin - VirtualHost + JkMount. This way Apache HTTP Server can not start. If I comment out the line JkMount /* ajp13, it starts without a problem. BUT if I put the following line, which is the same as in mod_jk.conf, before the mentioned VirtualHost again, the service can start! <IfModule !mod_jk.c LoadModule jk_module "C:/xampp/tomcat/xampp/apache/modules/mod_jk.so" </IfModule Why do I have to put this line in again? Why does that happen, that the http://localhost/example does work, so this query is redirected to AJP13, but I have to put the LoadModule line in again in another file? EDIT: I don't have a clue why, I surely modified something, but now /example doesn't work either... And the config above gives a 500 Internal Server Error... :S Thanks!

  Read the article

• HP ProBook 4540s - Can't find HP Protect Tools to activate fingerprint reader

  - by CandiM

  I got an HP ProBook 4540s in December--When I first got it, every time I booted up, there was a rather large icon, almost like a Windows 7 gadget, to access HP Protect Tools, but I had too much going on to mess with it right away and kept clicking on something like "remind me next time I log on" and determined to get acquainted with it after the holidays--But at some point in time, that icon went away and now I can't locate it at all-- I'd like to try, and probably use, the fingerprint reader and explore whatever else is among the Protect Tools, but now I can't find them or any folder or .exe to acceess them-- Can anyone help me find them?-- Thanks so much

  Read the article

• fdisk -l only displays boot partition

  - by Franklin

  I have a SAN, and it's able to read and write to the 50TB RAID just fine, but when I run fdisk -l it only lists the boot partition of the SAN server, and doesn't display anything about the other partitions on the RAID. I've also tried using parted -l with the same result. Now when I type mount it shows that the partitions are mounted just fine. I've never seen this happen. The box is running Openfiler 2.3 (I know it's old, we're in the process of upgrading all our old equipment). We have another SAN that's configured almost identically, and it's able to display the partition info with either of the two commands I mentioned above.

  Read the article

• update terminal title from standard output of long running command?

  - by Sam Hasler

  I'd like to change the title of a terminal window during a long running command (for example: git svn fetch) with values greped from the output, whilst still writing to standard output. Is this possible using named pipes or tee and xargs? I'm thinking something like git svn fetch | sed "s/^\(r\d*\).*$/ \"\\\033]0;\"\1\"\\\007\"/" | xargs -l1 echo -ne based on: http://tldp.org/HOWTO/Xterm-Title-3.html Update: getting this to work would be enough: (echo "r9" ; echo "r10") | sed "s/^\(r\d*\).*$/ \"\\\033]0;\"\1\"\\\007\"/" | xargs -l1 echo -ne Update 2: This almost does what I want. I see r10, but not r9: (echo "r9" ; sleep 1 ; echo "r10") | sed "s/^\(r[0-9]*\)\.*$/\\\033]0;\1\\\007/" | xargs -0 echo -ne

  Read the article

• rsync doesn't use delta transfer on first run

  - by ockzon

  I'm trying to synchronize a large local directory (with a batch file using rsync 3.0.7 on Cygwin, Windows 7 x64, 30k files, 200gb size) to a remote server (Debian x64 with kernel 2.6, rsyncd 3.0.7) over a slow internet connection (90kbyte/s upload). I know almost all files are identical and I verified that using md5sum locally and remotely. However when executing rsync from my local machine every file gets transferred completely for the first time. When I terminate the batch file after a few transfers and run it again then the already transferred files are skipped. But as soon as it gets to a file not yet transferred it uploads the file as a whole again instead of noticing that the checksum is the same locally and remotely. The batch file calling rsync looks like this (backslashes and line brakes added here for readability): c:\cygwin\bin\rsync.exe --verbose --human-readable --progress --stats \ --recursive --ignore-times --password-file pwd.txt \ /cygdrive/d/ftp/data/ \ rsync://[email protected]:33400/data/ | \ c:\cygwin\bin\tee.exe --append rsync.log I experimented using the following parameters in varying combinations but that didn't help either: --checksum --partial --partial-dir=/tmp/.rsync-partial --compress

  Read the article

• Windows 7: How to prevent Windows from caching my desktop wallpaper

  - by rmartz

  I have a service running that renders a changing wallpaper every 5 minutes or so, and replaces the current image file with the new one automatically (That is to say, new image but same filename). On Linux, the change is detected almost automatically, and so I have the most current wallpaper. However, on my Windows 7 machine (Which syncs the image with my Linux machine over Dropbox), it appears to cache the wallpaper from the last time I manually set the wallpaper. The image never changes, even if I restart. Is there a way to make Windows detect the file change, or periodically refresh the wallpaper cache? I'd like to avoid third-party apps if at all possible.

  Read the article

• Windows 7 Line In Delay Issue

  - by CheeseConQueso

  Not sure if this question should be posted on a different stack exchange site, so if you find that it should not be posted here, please move it. Either way, if you know the solution, please advise. I'm running Windows 7 Pro 32-bit on my Dell Latitude 2100 netbook and I'm having an issue with the line in device/driver/functionality. The device & driver are stock: Driver Date: 7/13/2009 Driver Version: 6.1.7600.16385 I'm almost sure that the manufacturer of the sound card is RealTek. The problem is that there is a delay (when monitoring input) between the source and the speakers. My setup is bass guitar running through a 12' long instrument cable (1/4") with a 1/4" female to 1/8" male adapter into the line in port on the computer. Then the 15' long headphones/line out cable goes into a standard set of powered speakers. How do I get rid of this delay? Thanks for any help.

  Read the article

• Outlook new message size nearly 1mb

  - by Yossi Dahan

  I've been using Outlook 2010 for several weeks with no issues. Suddently, a few days ago, the size of my outgoing messages got huge. Looking at thsi it appeas that a huge CSS style is beign created with around 14,000 definition for list items, making the message almost 1mb before I even typed in one word. Emails before that point were very small. Needless to say I can't remember changing anything, nor can anyone around here provide any possible explanation... Any ideas?

  Read the article

• How do i enable deflate on apache2? debian

  - by acidzombie24

  I looked at the other answers and those solutions did not help. I am completely confused how to do this. I know almost nothing about apache nor how to use it and nearly all the article say write this but doesnt tell me where. So far i have done this # a2enmod deflate Module deflate already enabled Then i tried writing this in httpd.conf AddOutputFilterByType DEFLATE text/html text/plain text/xml text/css Then i wrote a longer version which involved deflate.c. After those didnt work i deleted them all and wrote the AddOutputFilterByType line in apache2/sites-enabled/000-default inside of I used this to test http://www.whatsmyip.org/http_compression/ everytime it says no compression. I used another site but i could never compress. Also i restart the server everytime i save a file so what could be the problem and how do i enable this properly?

  Read the article

• How can I improve performance over SMB/CIFS for an application that has poor write speeds?

  - by Jeremy

  I have a third party application that reads several large files and generates a third large file. Its performance is quite good when the generated file is stored on "local storage", i.e. either a direct attached or iSCSI-based disk. The source files that are read can be stored remotely on our NAS and accessed via SMB with little effect on performance. However, if we attempt to write the target file to any kind of SMB/CIFS share (Samba or Windows Server) the performance drops almost ten-fold. This is unacceptably slow in our case. Writing files to network shares is not otherwise slow. I can copy large files to SMB shares and get great performance - near what I would expect is possible given the disks and network in question. I have a theory that this application's problem with SMB shares has something to do with a lack of write caching over the share and perhaps lots of network roundtrips. Is this possible and is there anything that can be done about it?

  Read the article

• Video converters don't work anymore after reinstalling Windows

  - by tassiekev

  A few days ago, I decided to reinstall Windows 7 as my HD partition seemed to be nearly full and things were slowing down. I'd been using Handbrake almost exclusively to convert TV recordings and used Freemake on occasion. Following the reinstall, I can't get either to work: Handbrake says it's encoding for about 2 seconds and then says it's finished, but there are no converted files of any size. Freemake just says 'Conversion Error' and won't go any further. As an experiment I tried two programs that I don't normally use, VideoReDo & Any Video Converter. Both worked fine. Anyone got any clues?

  Read the article

• verisign certificate into jboss server SSL

  - by rfders

  i'm trying to enable jboss to uses ssl protocol using a previously generated certificate from verisign, i imported both certificate, server certificate and ca certificate into the keytore file, and i configured the server.xml to use that keystore and activate ssl protocol, then when i run the jboss, I got this error "certificate or key corresponds to the SSL cipher suites which are enabled" Question, reading some post on internet, i found that every example was made it generating a Certificate Request, it stricly necesary to do that if i already have the server certificate and that CSR has to be imported into the keystore as well ? at this point i'm very confused about this issue, i tried almost every solutions posted in several forums but till now i haven't any luck !! can you give me some tips in order to solve this problem. thanks in advance this are my keystore file: Keystore type: jks Keystore provider: SUN Your keystore contains 2 entries j2ee, Dec 29, 2009, trustedCertEntry, Certificate fingerprint (MD5): 69:CC:2D:2A:2D:EF:C4:DB:A2:26:35:57:06:29:7D:4C ugent, Dec 29, 2009, trustedCertEntry, Certificate fingerprint (MD5): AC:D8:0E:A2:7B:B7:2C:E7:00:DC:22:72:4A:5F:1E:92 and my server.xml configuration:

  Read the article

• Software to draw custom street maps?

  - by jay

  I'm looking for any (Windows) software that allows me to draw custom street maps. I'm not looking for something that displays existing maps from real places, but something that allows me to define my own map. Obviously this can be achieved through any graphics program however I am wondering if there's a software which makes it almost drag-drop easy to create your own maps of visual quality to that of Open Street Maps, Google Maps, street directories etc. Preferably an offline desktop app with attention on design rather than complex geospacial specifics. Context: I want to make a detailed street map for a game I'm making.

  Read the article

• SEAGATE Barracuda 7200.11 HDD not running

  - by Dane411

  After a huge research, I'm stuck at the beggining of getting my HDD data back. Whats happening to me is that in the moment when I plug the power wire to my external 1TB SEAGATE Barracuda 7200.11 ST31000333AS HDD Fw LC15, it makes the sound like it's spinning to almost full speed and then shuts down and spins up again, and so on. It's well known that those HDDs have a bad firmware that someday randomly fails. There are like 2 main problems identified, BSY (busy) state, and LBA0 error. Last time I connected it to power nothing happened, it didnt try to start at all, is it that so called bricked state? I guess my HDDs error is the first one, but I dont really know if what I described is that BSY state or not, neither I know how to check it. How could I know it? Thank you so much!

  Read the article

• compressing dd backup on the fly

  - by Phil

  Maybe this will sound like dumb question but the way i'm trying to do it doesn't work. I'm on livecd, drive is unmounted, etc. When i do backup this way sudo dd if=/dev/sda2 of=/media/disk/sda2-backup-10august09.ext3 bs=64k ...normally it would work but i don't have enough space on external hd i'm copying to (it ALMOST fits into it). So I wanted to compress this way sudo dd if=/dev/sda2 | gzip > /media/disk/sda2-backup-10august09.gz ...but i got permissions denied. I don't understand.

  Read the article

• Terminal Server 2008 - Slow File open dialog in Office 2003

  - by Chris

  I have yet another small issue that annoys me everyday in our Terminal Server environment. It seems when logging into Terminal Server users report the initial File | Open or File | Save As from within an application such as Word, Excel (2003 edition) is very slow to display the actual dialog box. The dialog appears quickly but it is whited out (sometimes displays not responding in title bar) and unresponsive, it then sits like this for about 20-30 secs before popping into life and displaying all the folders etc. The second time you go to save or open a file it loads almost instantly. Any suggestions or similar problems out there?

  Read the article

• Can't access files on external drive after reformatting Macbook Pro

  - by Peter Wells

  I recently had to reformat my Macbook Pro, and imported my account and settings from Time Machine via the Migration Assistant. Everything on the Mac itself is fine, but now I don't have permission to access almost everything on my external drive. A number of folders have the little red 'no access' sign on them and I can't rename or move anything. Looking at the info for these files, it appears that access rights were attached only to my old user account. Is there some way to reassign these files and folders to my new user account? Thanks.

  Read the article

• ATI Radeon Drivers works with which linux distribution and version?

  - by amit.codename13

  I have ATI Mobility Radeon HD 5850 graphics card. Almost every new linux distribution seems to have an issue with it, when i install the drivers. Working without utilizing the graphics card leaves me so unproductive. So i made a plan to use older versions of linux, any distribution suitable as a desktop distribution. UPDATE: The kind of problems that i am facing are, 1) After installing drivers the system boots and hangs, 2) There are unusual lines over the screen 3) After upgrade system doesn't start properly(hangs the usual old way) The kind of answers i am looking for is, distribution X(the newer the version the better) doesn't have the above problem after installing drivers for ATI Mobility Radeon HD 5850 graphics card. UPDATE: The new drivers released by AMD seems to fix all the issues, although they are still beta Thanks

  Read the article

• Difficulty racking Proliant G8's

  - by Systemspoet

  We're an all Proliant shop with around 50 servers, mostly DL360s and DL380, from G5's through G7's. We just got our first two G8's in and went to rack them. We were stunned to find out that the new cable management arms protrude almost 1 inch deeper into the rack then previous iterations of the Proliant line. Unfortunately that causes them to occupy the same space as the PDU's in our APC racks. In a non-densely populated section of rack that's no biggie, but in a densely populated section it's impossible to get the cable arm into place without dislodging another machine's power. Has anyone else run into this? Obviously racking machines without cable management arms is not an option. I supposed we could reconfigure our racks but that's a nightmare.

  Read the article

• What is the simplest and fastest way to transfer large file through a Windows network?

  - by Sake

  I have a Window Server 2000 machine running MS SQL Server that stores over 20GB of data. The database is backed-up every day to the second harddrive. I want to transfer those backup files to another computer to build another test server and for recovery practicing. (the backup never actually got restored for almost 5 years. Don't tell my boss about that!) I have trouble transfering that huge file through the network. I've tried plain network copy, apache download, and ftp. Any method I tried end up failing when the amount of data transfered reach 2GB. The last time that I successfully transfered the file, it was through a usb attached external harddrive. But I want to perform this task routinely and preferably automatically. Wonder what is the most pragmatic approach for this situation ?

  Read the article

• Windows XP Task Management: no execution

  - by Ice09

  Hi, we used the following scenario sucessfully over a long period of time: Remotely log onto a Win XP server, which is used by one user most/all of time Schedule a task using the "task planner" Task was run at "almost" each scheduled point of time (seldom it did not start, presumably when someone else was logged in). For some time now, we share the server with several users. Even though I checked an option for running independently of the logged in user, this option does not seem to work. Now, the task is seldom executed, not seldom not executed. Now, the question is: is there some other option I can't see which disables the execution OR, even better, is there some other tool which we can use for task scheduling on Win XP servers with several different users?

  Read the article

• In ADUC MMC, Advanced View, how to get Attribute Editor tab on the result of a Find?

  - by geoffc

  In Win2008 MS added a new Tab on objects in ADUC. Called Attribute Editor it is like Novell Console One's Other tab, or an arbitrary LDAP editor view, or an ADSI Edit style view. Basically it shows all allowed attributes for the object class, and allows you to edit according to your permissions. You need to enable Advanced Options in the View menu before it shows up. This is great, however it only shows up when you browse the directory tree and select an object. If you use the Find tool and open an object Attribute Editor is not shown. How annoying! Especially if your domain has more than 2000 users in a single container, then you almost must use Find to get to an object. Is there any way to make the Attribute Editor tab show up after using Find to open an object?

  Read the article

• How do I make a Windows virtual machine replicate to another datacenter/cloud?

  - by zippy

  We have a Windows 2008 VM running IIS and SQL Server Express (it's an all-in-one web application). We need to have another copy at our secondary datacenter site. What is the best way to do this? It doesn't have to be running all the time but it has to have almost the latest copy of the current VM. I took a look at VMWare Fault Tolerance and after the heart attack at the price I starting looking for another solution. If need be I wouldn't mind copying it over to a cloud VM provider, if I can find one that lets me copy my own VMs up and start them up without any conversion process.

  Read the article

• Problem with creating table on phpMyAdmin database

  - by tombull89

  Hello all, I'm running a phpMyAdmin Database on my web package on a 1and1-hosted server. I've managed to set up a database in the control panel, have uploaded all to root/phpmyadmin and changed the config.ini.php file to point at 1and1's database server (because that's the way they do it). I can go to the web interface and get to the main page, but all it shows is the database name and I can't find how to create any tables. I know it's a long shot but I'm almost out of ideas. Also, 1and1 have their own phpmyadmin panel, which is pretty annoying to use, and a 1and1 webdatabase which I have barely looked at. Help and suggestions much appriciated.

  Read the article

< Previous Page | 101 102 103 104 105 106 107 108 109 110 111 112  | Next Page >