Search Results

Search found 6815 results on 273 pages for 'micro sd card'.

Page 105/273 | < Previous Page | 101 102 103 104 105 106 107 108 109 110 111 112  | Next Page >

• Building a new PC, Installing XP, blue screen of death

  - by Tim

  I got a gigabyte barebones kit and am installing windows-XP(SP1) and the initial setup works, then it restarts and goes into the second phase of the setup. Then when installing components (I think that's what it says) it gets half way done and comes up with a blue screen saying IRQL_NOT_LESS_OR_EQUAL. BUT! I had gotten past that by installing windows-XP media center addition Now I am trying to install the drivers for my Asus ATI Radeon 5770 graphics card and I get another blue screen of death that doesnt give much info something about address x0000005. Would you think there is something wrong with something in my system or do you think if I got windows 7 that would take care of things? Sorry for probably not giving enough info. Here is what I have MotherBoard - Gigabyte S-series GA-H55M-S2(v) PSU - Ultra 500 watt atx HDD - Sata serial ATA Seagate Baracudda 7200 CPU - Intel i3 Memory - 4gig crucial Graphics Card - Asus ATI Radeon 5770 1Gig DDR5

  Read the article

• Mother Board Question

  - by user33931

  1st, I am software guy. I do not do hardware. So I know to you hardware geeks, this is a dumb question. I just inherited a box with a ASUS P5GZ-MX mother board. I have attempted to install two nVidia PCI video cards. I put a 750w power supply in the system to be sure I have enough power. With no extra video cards, the 3.3 v shows normal. When I put one card in, the 3.3 goes to 3.5-3.6 and flashes red (over voltage) about 30% of the time. When I put the 2nd card in, it goes to 3.73 v and stays red all the time. Any Ideas why the voltage goes up when I add cards instead of going down? More Importantly, is this dangerous to the system?

  Read the article

• Laptop hot after format

  - by Dany Khalife

  I recently formatted an HP G62 Laptop and installed all drivers from the HP site that should be installed for this model. But i noticed a very strange behavior, using Coretemp, the temp is always above 50 (on idle) and reaches 70 very quickly sometimes (Critical is 90) If i open youtube or skype alone, i can get temperatures as high as 83. Normally it was around 32 (on idle) and reaches 70 when i open games but not youtube.... I have a i3 processor and AMD graphics so i am wondering if somehow it's a graphics card issue (since i3 has integrated graphics as far as i know) Device manager shows only AMD graphics card tho, not sure if i3 graphics should appear here too. Any ideas what i might have forgotten to do after the format ?

  Read the article

• Super-silent (mid tower) case and fan combo

  - by Dennis G.

  I want to build a HTPC for music/video/blu-ray playback (no gaming). I don't need an expensive HTPC case but just want to go with a standard medium tower case. However, I want it to be super silent so it doesn't make any annoying fan/disk noises when I watch movies. Ideally, it shouldn't make any noticeable noise at all. I understand that choosing a board, CPU and graphic card that run cool and don't consume a lot of power is important for designing a quiet machine, and I think I got that covered. However, there are so many choices in regards to cases, fans and power supplies that it's hard to get started. What are your recommendations for a case/fan (cpu+case)/power supply combination that run absolutely silent and can cool a standard Intel system with a low-power (possibly passively cooled) graphic card? I'm usually a fan of Antec cases, would an Antec Mini P180 be a good starting point? If so, which case fans, CPU fan and power supply would you recommend?

  Read the article

• Sort on DataView does not work if DataTable has zero rows

  - by BigBlondeViking

  We have a WPF app that has a DataGrid insode a ListView. private DataTable table_; We do a bunch or dynamic column generation ( depending on the report we are showing ) We then do the a query and fill the DataTable row by row, this query may or may not have data.( not the problem, an empty grid is expected ) We set the ListView's ItemsSource to the DefaultView of the DataTable. lv.ItemsSource = table_.DefaultView; We then (looking at the user's pass usage of the app, set the sort on the column) Sort Method below: private void Sort(string sortBy, ListSortDirection direction) { var dataView = CollectionViewSource.GetDefaultView(lv.ItemsSource); dataView.SortDescriptions.Clear(); var sd = new SortDescription(sortBy, direction); dataView.SortDescriptions.Add(sd); dataView.Refresh(); } In the Zero DataTable rows scenario, the sort does not "hold"? and if we dynamically add rows they will not be in sorted order. If the DataTable has at-least 1 row when the sort is applied, and we dynamically add rows to the DataTable, the rows com in sorted correctly. I have built a standalone app that replicate this... It is an annoyance and I can add a check to see if the DataTable was empty, and re-sort... Anyone know whats going on here, and am I doing something wrong? FYI: What we based this off if comes from the MSDN as well: http://msdn.microsoft.com/en-us/library/ms745786.aspx

  Read the article

• after upgrade to outlook 2013 Contacts have the default picture in reading pane

  - by Juan Zamudio

  I'm using Windows 8 on a domain (using a domain account not a Microsoft account) connecting to Exchange, all my Contacts were outlook contacts with pictures and other data, I could see the picture of the contact in the reading pane and people pane while using Outlook 2010. After the upgrade to Outlook 2013 I can see my outlook contacts but it appears that they are unavailable in the reading pane because all i can see is the default picture (the default picture picture is also visible in the notifications). If I put the mouse over the name of the people while in the reading pane all I can see is the card with the default info (the only data is that the contact is available in the next 8 hours), if i compose a new message and hover the name of the contact i can see the card with all the data (picture, company, etc.). Is this the default behavior in Outlook 2013 if you are in a domain and not connected to any service or there is a way to show the picture of my contacts in every part of outlook?

  Read the article

• Are these components compatible and are there any significant bottlenecks?

  - by Tom Gullen

  I'm trying to buy a new pc, for software dev and a bit of gaming. I already have a 500gb HDD , and a PCI sound card I want to use as well. Is all this stuff compatible, and will it all work together and are there any significant bottlenecks? Case, Mobo and PSU "Primo Motion" AMD 880G DDR3 Ready Barebones (Socket AM3) http://www.overclockers.co.uk/showproduct.php?prodid=FS-268-OK&groupid=43&catid=1817&subcat= SSD 64GB Crucial RealSSD C300 64GB 2.5" SATA 6Gb/s Solid State Hard Drive http://www.overclockers.co.uk/showproduct.php?prodid=HD-007-CR&groupid=1657&catid=1660&subcat=1668 CPU AMD Phenom II X6 Six Core 1090T Black Edition 3.20GHz (Socket AM3) http://www.overclockers.co.uk/showproduct.php?prodid=CP-266-AM&groupid=701&catid=6&subcat=1944 RAM 8GB Corsair Vengeance 8GB (2x4GB) DDR3 PC3-15000C9 1866MHz Dual Channel Kit http://www.overclockers.co.uk/showproduct.php?prodid=MY-292-CS&groupid=701&catid=8&subcat=1387 Graphics XFX ATI Radeon HD 5770 1024MB GDDR5 PCI-Express Graphics Card http://www.overclockers.co.uk/showproduct.php?prodid=GX-149-XF

  Read the article

• mobile broadband recommendations for Lenovo T500

  - by Justin Grant

  I use a Lenovo T500 primarily in and around San Francisco, although I do some travel in the US on business and occasionally to Europe/Asia. I'm looking for a good mobile broadband option for my T500. I am admittedly baffled by the various mobile-broadband choices (3G vs. 4G, WiMax vs. LTE vs. MIMO vs. ..., etc.). My priorities are (in this order): Compatible with Lenovo T500 and Windows 7. I realize only the AT&T accessory card is listed on Lenovo's site, but I've also heard that other cards will work in my T500 too, like the WiMax/Wifi combo card-- so I'm interested in what actually works, not necessarily only what Lenovo is promoting. Reliable coverage in US large cities, especially the SF Bay Area. my IPhone has lousy coverage in many spots, so I'd be nervous about an AT&T 3G option unless the problem is with the IPhone and not AT&T's network. I'm OK with non-great coverage outside major US cities, since I don't do much travel in those areas. Speed. faster is better. Internal card. I'd slightly prefer something I could install inside my T500 instead of a dongle on the side that might break off, although this is my lowest priority so it's not a big deal. Price. I don't want to pay over $100/month. I've tried lots of Googling and haven't come up with clear answers. I've seen lots of general overviews without recommendations, and lots of passionate opinions which don't feel objective (and don't help me understand compatibility with my hardware & geography). Can you recommend a good, objective guide online, ideally for Lenovo although general guide is OK too, which can help me figure out which option is the best one for me? I'd also be interested in your own personal experiences of using mobile broadband using a Lenovo T500. I'll accept the answer which gets me closest to making a decision.

  Read the article

• How do I keep second monitor (HDTV) from auto-disabling in XP when it is turned off?

  - by ThantiK

  I have a new 32" TV that I hooked up to the HDMI port on the back of my video card to use as a second monitor. I used an HDMI/DVI cable to hook it to the TV, and whenever I turn my TV off, XP disables the device tied to the TV so each time I want to use the TV as the monitor, I have to go into my display properties and enable it; it gets pretty annoying. How do I turn this 'feature' off? -- I have an NVidia card should it be specific to the nvidia control panel.

  Read the article

• How to Connect Firewire Camcorder to Laptop without firewire port

  - by bdk

  I Have a Sony Camcorder w/ a 4-pin firewire output. I have HP laptop I want to use it with, but the laptop, does not have a firewire port, just VGA, HDMI, USB, ESATA, Ethernet, and Modem. In addition, It doesn't have a PC Card slot for adding a Firewire card. Googling for "Firewire to USB adapter" returns a lot of hits, but no product that seems to do what I want. I assume I need a USB dongle that gives a firewire port and has drivers so that the PC sees it as a regular firewire port. Thanks for any recommendations

  Read the article

• Bridge virtual machines out WLAN interface

  - by Thomas

  It seems that my wlan card (intel 5100 AGN) firmware doesn't allow "spoofing" MAC addresses. This has the side effect of destroying the capability to bridge out my virtual machines on that interface. Apparently this is a common thing on wlan cards. I can see the incoming traffic just fine in my virtual machines, but their DHCP queries don't get bridged out of the WLAN card. It works perfectly well when using the wired ethernet port. Is there a workaround for this? MAC-NAT or something? I don't want to route my virtual machines out to the Internet because I don't want my host OS to even have an IP address. I'm using Linux and KVM for virtualization.

  Read the article

• Discover MAC address

  - by Kami

  I've to setup a bunch of server ! I need to discover their mac address with the following situation : MacBookPro >----------< Server I'm directly connected (not behind a router/switch) to the server. I've no clues about the ip address the server is using as default setup. I can't use a display connected to the server displaying its newtwork card config. How can I discover the MAC address of the server network card ? I'm looking for a command line tool. If something exists in MacPort it's also ok !

  Read the article

• Stuck in power saving mode

  - by sazabi02

  I've got an LG monitor I tried attaching to my laptop for dual monitor goodness and it worked fine but when I tried attaching it back to the desktop it stuck in "Power Saving mode" and wouldn't go away. The CPU's starting up but nothing happens with the monitor. I try attaching it back to the laptop and it works fine again. I don't understand what could have happened. For reference, the laptop I'm using is an HP laptop with nVidia GT240M video card running on an i7 processor while the desktop runs on a Dual Core processor with an nVidia 9400GT video card. I've never had problems like these with other monitors I've attached my pc to. Anyone got any ideas?

  Read the article

• 802.11 Capture Frame

  - by ALi

  I am using wireshark in monitor mode to capture all the frame. I buffered all the QosData in order to calculate the biterate of each station on the network. I calculate the biterate but it is not an accurate value. what i need to know is when the station use the network alone and when it uses it with another station? i know if two station with different wifi card for exemple ( st1 802.11g 54 Mb/s, st2 802.11n 300 Mb/s) if st1 uses alone the line the biterate used is 28 MB/s and if st2 uses alone the network the bit rate increase to approximately 150Mb/s but if the two station use the network at the same time the st1 lost about 80% of its bit rate because of the st1 wifi card thx in advance

  Read the article

• Can I set up a 2nd home wireless router, with router2 connecting to the internet through a desktop which is wirelessly connected to router1?

  - by gil b.

  Hi, I apologize for the crudeness of my MSPaint drawing, but please view my diagram of what I'd like to accomplish: Proposed home network architecture Currently, all devices are connected to 1 wireless router. I would like to make my own subnet, with a box in-between my subnet and the shared wireless router, so that I can learn about IDS, traffic analysis, etc. I was also given a cisco PIX firewall to play around with, and it'd be an added bonus if I could incorporate that into my network. The reason for this proposed architecture is so that I can monitor all MY traffic, without seeing anything going on with my roommates' traffic. my MAIN Question is, is it possible to have my desktop connect to the wireless router with internet via wireless card AND share that connection via the ethernet card, hooked to wireless router 2? cable modem - wireless router - desktop pc connected wirelessly - wireless router 2 getting internet from wired connection to desktop pc - laptops connected wirelessly The PIX can be left out for now, but I'm wondering if it could eventually be incorporated? THANKS!

  Read the article

• How do you test if a PCI slot is working - motherboard diagnostic software?

  - by Adam

  I suspect that my motherboard is bad, and that my PCI-E slot is not working. I have a Gigabyte motherboard that had a Hauppage 2250 working fine in the PCI-E slot for many months. However - recently - would not get TV channels that I used to get --- until finally Media center cant detect any channels at all. Got a new tuner card (ATI 350 card) - cant detect any channels. The cable signal is good - I have it connected directly to a TV - all channels come in clear. SO that is why I suspect a motherboard problem. Are there any motherboard diagnostic scanner utilities that can verify I need a new motherboard

  Read the article

• snow leopard: how can i monitor loading of specific extensions?

  - by ufk

  Hiya. I'm installing VoodooHDA extension in order for Intel 82801I (ICH9 Family) HD Audio 8086:293E sound card to operate. The sound card does not work but i have no idea how to debug the issue. How can I check if the module was loaded properly? how can i make sure that there where no conflicts? how can i make sure that there were no dependencies issues with another module? Using snow leopard 64 bit. thanks!

  Read the article

• How to forward UDP and TCP traffic from one IP to another

  - by Rishabh Agnihotri

  Well i have a server with two LAN Card Installed.I have a server in U.S and one in India.I have created a GRE tunnel to route all traffic from U.S Server to my Indian Server.My Traffic has UDP,TCP,HTTP,etc Traffic.Now i have two LAN Card on my Indian Server.Well i have configured two IPs on the system for some of my needs on the system.One is a /30 and another is a /24.Well now i want the /30 IP to talk to my /24 IP.Lets take a e.g the IPs are 180.151.130.34 - /30 and 103.243.19.254 -/24 I want to forward all the TCP,UDP,HTTP,etc like traffic coming to 180.151.130.34 to 103.243.19.254.In the sense i want to make them talk to each other in a way if a TCP/UDP Packet comes to 180.151.130.34 it should be forwarded to 103.243.19.254 and then that packet is sent back by 103.243.19.254 to 180.151.130.34.I am not able to configure this part.Can anyone tell me step by step how to do so? Well i forgot to specify i am using Windows Server 2008. Any help would be greatly appreciated.Thanks in advance.

  Read the article

• Why cant I get 3 monitors working with my ati 5770

  - by G-Dogg

  I have an ati 5770, card with vga, dvi and hdmi output. I can only get 2 out of the 3 monitors working at once, however i can change the configuation so that all monitors can be selected, but only 2 will work at once.. 2 of my monitors have dvi inputs and one has vga. in my catyalist control center it shows all 3 monitors are there but either 2 can be selected at a time, and so the same with my windows 7. I have and adapter which i use on the 3rd monitor, hdmi-dvi adaptor and it works. also when i boot up my pc i get 2 monitors booting up and when windows starts the 3rd monitor boots but the 1st one closes. I looked at my package box and it actualy does specify ati eyefinity technology is available with this card. why wont it work???

  Read the article

• Using multiple wifi connections simultaneously on Windows

  - by Salman A

  My office PC has a one wireless network card and there are three available wifi connections: primary, backup and backup of a backup (grin). Is it possible for me to use all three simultaneously. If this results in an increase in bandwidth that's well and good, but primary reason is every now and then one of the network fails and i have to switch back and forth between the available networks by disconnecting, viewing available networks and connecting to next one hoping its running. Do i need more than one network card or a software e.g. a proxy.

  Read the article

• Using multiple wifi connections simultaneously on Windows

  - by Salman A

  My office PC has a one wireless network card and there are three available wifi connections: primary, backup and backup of a backup (grin). Is it possible for me to use all three simultaneously. If this results in an increase in bandwidth that's well and good, but primary reason is every now and then one of the network fails and i have to switch back and forth between the available networks by disconnecting, viewing available networks and connecting to next one hoping its running. Do i need more than one network card or a software e.g. a proxy.

  Read the article

• How to reset video/display drivers in Vista without restarting OS?

  - by jdk

  Currently I have to reboot my system if an external monitor is hooked up for it to be correctly detected and used. I think it would be faster to restart/reset the video or display drivers instead. How do I do this under Vista? I seem to remember from an old laptop using a Windows command-line command that would restart the wireless networking card device when it crashed. Is there something like that for video drivers? Background/Reason Because people rightfully ask why? - This is part of a larger problem which I'm waiting for resolution on from the manufacturer. In the meantime I'm looking for the above quick fix. Actually my video card often crashes my laptop when attaching an external monitor and trying to detect or use it. No solution from vendor yet and latest drivers do the same irksome behaviour. Windows says: A problem with your video hardware caused Windows to stop working correctly.

  Read the article

• How to reset video/display drivers in Vista without restarting OS?

  - by jdk

  Currently I have to reboot my system if an external monitor is hooked up for it to be correctly detected and used. I think it would be faster to restart/reset the video or display drivers instead. How do I do this under Vista? I seem to remember from an old laptop using a Windows command-line command that would restart the wireless networking card device when it crashed. Is there something like that for video drivers? Background/Reason Because people rightfully ask why? - This is part of a larger problem which I'm waiting for resolution on from the manufacturer. In the meantime I'm looking for the above quick fix. Actually my video card often crashes my laptop when attaching an external monitor and trying to detect or use it. No solution from vendor yet and latest drivers do the same irksome behaviour. Windows says: A problem with your video hardware caused Windows to stop working correctly.

  Read the article

• Laptop recommendation for home user

  - by Mehper C. Palavuzlar

  I'm going to buy a new laptop soon and I need Super Users' recommendations. The following criteria are crucial for me: Intel i series processor Min. 4 GB RAM Min. 500 GB HDD HDMI port Min. 3 USB ports Not a monster, but a good graphics card Multimedia card reader DVD-RW Double Layer No heating problems! What do you recommend me? I'm considering buying a Vaio but I'm not sure. TIA.

  Read the article

• Hyper-V extensible virtual switch disables network

  - by Sebastian Krysmanski

  I just installed the Hyper-V role on my Windows Server 2012. It comes with something called a "Hyper-V extensible virtual switch". I assigned it to the only network card in my server. By doing so, the network card became useless/disabled/inactive/.. because the virtual switch disabled all features (IPv4, IPv6, Client for Microsoft Networks, ...) on the network adapter. Is this supposed to happen? I admit I've no idea what this "extensible virtual switch" actually does. A short explanation would be nice as well.

  Read the article

< Previous Page | 101 102 103 104 105 106 107 108 109 110 111 112  | Next Page >