Search Results

Search found 29222 results on 1169 pages for 'network security'.

Page 1053/1169 | < Previous Page | 1049 1050 1051 1052 1053 1054 1055 1056 1057 1058 1059 1060  | Next Page >

• IPv6 Routing / Subnetting

  - by nappo

  Recently I have installed Citrix Xen Server 6.2 on a machine. My Provider (Hetzner) gave me the IPv6 Subnet 2a01:4f8:200:xxxx::/64. Followed an article in the providers wiki (1) i got it working and can assign IPs to my guests (CentOS). However i can't assign a second IP to a single guest - it will result in a timeout. I'm not very familiar with IPv6 routing / subnetting - any help or tips for further troubleshooting is welcome! My Setup: XenServer 6.2 IPv6: 2a01:4f8:200:xxxx::2/112 ip -6 route: 2a01:4f8:200:xxxx::/112 dev xenbr0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 0 fe80::1 dev xenbr0 metric 1024 mtu 1500 advmss 1440 hoplimit 0 default via fe80::1 dev xenbr0 metric 1024 mtu 1500 advmss 1440 hoplimit 0 Guest 1 IPv6: 2a01:4f8:200:xxxx::3/64 IPv6: 2a01:4f8:200:xxxx::4/64 ip -6 route: 2a01:4f8:200:xxxx::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via fe80::1 dev eth0 metric 1 mtu 1500 advmss 1440 hoplimit 4294967295 Guest 2 IPv6: 2a01:4f8:200:xxxx::5/64 Guest 1 IPv6 is working fine, Guest 2 too. As suggested by the wiki article (1) i split my /64 network into a /112. Is it right to set the host /112 and the guests /64? Why is that?

  Read the article

• Managing an application across multiple servers, or PXE vs cfEngine/Chef/Puppet

  - by matt

  We have an application that is running on a few (5 or so and will grow) boxes. The hardware is identical in all the machines, and ideally the software would be as well. I have been managing them by hand up until now, and don't want to anymore (static ip addresses, disabling all necessary services, installing required packages...) . Can anyone balance the pros and cons of the following options, or suggest something more intelligent? 1: Individually install centos on all the boxes and manage the configs with chef/cfengine/puppet. This would be good, as I have wanted an excuse to learn to use one of applications, but I don't know if this is actually the best solution. 2: Make one box perfect and image it. Serve the image over PXE and whenever I want to make modifications, I can just reboot the boxes from a new image. How do cluster guys normally handle things like having mac addresses in the /etc/sysconfig/network-scripts/ifcfg* files? We use infiniband as well, and it also refuses to start if the hwaddr is wrong. Can these be correctly generated at boot? I'm leaning towards the PXE solution, but I think monitoring with munin or nagios will be a little more complicated with this. Anyone have experience with this type of problem? All the servers have SSDs in them and are fast and powerful. Thanks, matt.

  Read the article

• How to tell statd to use portmap on a non-localhost ipadress?

  - by jneves

  How can I make statd connect to other IP address other than 127.0.0.1? I have a server that is connected to 2 different networks (one is public, another a private). I want it to provide a NFS share for only the private network. The host in an ubuntu 8.04. The private ip address is 192.168.1.202 I changed /etc/default/portmap to add: OPTIONS="-i 192.168.1.202" The command lsof -n | grep portmap returns: portmap 10252 daemon cwd DIR 202,0 4096 2 / portmap 10252 daemon rtd DIR 202,0 4096 2 / portmap 10252 daemon txt REG 202,0 15248 13461 /sbin/portmap portmap 10252 daemon mem REG 202,0 83708 32823 /lib/tls/i686/cmov/libnsl-2.7.so portmap 10252 daemon mem REG 202,0 1364388 32817 /lib/tls/i686/cmov/libc-2.7.so portmap 10252 daemon mem REG 202,0 31304 16588 /lib/libwrap.so.0.7.6 portmap 10252 daemon mem REG 202,0 109152 16955 /lib/ld-2.7.so portmap 10252 daemon 0u CHR 1,3 960 /dev/null portmap 10252 daemon 1u CHR 1,3 960 /dev/null portmap 10252 daemon 2u CHR 1,3 960 /dev/null portmap 10252 daemon 3u unix 0xecc8c3c0 4332992 socket portmap 10252 daemon 4u IPv4 4332993 UDP 192.168.1.202:sunrpc portmap 10252 daemon 5u IPv4 4332994 TCP 192.168.1.202:sunrpc (LISTEN) portmap 10252 daemon 6u REG 0,12 289 3821511 /var/run/portmap_mapping I defined in /etc/hosts the following: 192.168.1.202 server.local In /etc/default/nfs-common I changed STATDOPTS to: STATDOPTS="--name server.local" Yet when I run /etc/init.d/nfs-common start if fails to start. The log shows: Jun 8 06:37:44 cookwork-web1 rpc.statd[9723]: Version 1.1.2 Starting Jun 8 06:37:44 cookwork-web1 rpc.statd[9723]: Flags: Jun 8 06:37:44 cookwork-web1 rpc.statd[9723]: unable to register (statd, 1, udp). An strace -f rpc.statd -n server.local results in a lot of lines, including this one: sendto(9, "\200]3\362\0\0\0\0\0\0\0\2\0\1\206\240\0\0\0\2\0\0\0\1"..., 56, 0, {sa_family=AF_INET, sin_port=htons(111), sin_addr=inet_addr("127.0.0.1")}, 16) = 56

  Read the article

• how to back up data from a machine that keeps hanging

  - by Amit Phatarphekar

  Hello - I have a storage server running opensolaris. But lately its been acting up - it hangs at random times due to some SCSI/ATA related error messages. I've tried to fix it without any progress, so I'm giving up now. The machine keeps hanging every 30 minutes or 1 hr ...sometimes after 4 hrs. Its very unpredictable. So I've decided to just reformat the storage server and start from scratch...maybe I'll just not use solaris and install something else, since the errors are related to solaris running on ATA HDD or something. Question - Before I reformat it, I want to back up some of the important data on it. Like it has a VM with 200 GB disk files, it has a whole bunch of ISOs stored on it etc etc. I'm using a simple scp to copy the files over to a different machine. My issue is that, because the machine hangs....sometimes my file copy is incomplete and I have to start all over again. Lets say I'm trying to copy a 200GB file which takes like 4 hrs....IF the machine hangs before the whole file i copied over...I have to recopy the file from scratch. Is there a solution to copy the files over such that if the machine hangs or network goes down..the copying can resume from where it left off? - like if 50 GB of a 200GB file was copied and machine hung....next time, it'll just continue to copy rest of the amount, instead of starting all over again. Thanks Amit

  Read the article

• What is the IPv6 equivalent to IPv4 RFC1918 addresses?

  - by Kumba

  Having a hard time wrapping my head around IPv6 here. A lot of the lingo seems targeted at enterprise-level IPv6 deployments, discussing link-local, site-local, global unicast, scopes, etc. Not a lot of solid information on really small networks, like home networks. I want to check my thinking and make sure I am getting the correct translations from IPv4-speak to IPv6-speak. The first question is, what's the equivalent of RFC1918 for IPv6? Initial searches suggested there was no equivalent. Then I stumbled upon Unique Local Addresses (RFC4193), and that states that all ULA's should be assigned the prefix fc00, followed by a 40-bit random number in the routing prefix. This random number is to "prevent collisions when two IPv6 networks are interconnected" -- again, another reference to an enterprise-level function. If I have a small local LAN at home, numbered using 192.168.4.0/24, what's my equivalent in IPv6's ULA scope? Assuming I will never, ever, tie that IPv6 address into the real internet (a router will NAT & firewall it), can I ignore the RFC to an extent and go with fc00::4:0/120? It also seems that any address in fc00::/7 are to be globally routable. Does this mean I'll need extra protections so my router would not automatically start advertising these private IPv6 addresses to the world? Second question, what's this link-local thing? Reading suggests a default-assigned address in the fe80::/10 range that has the last 64bits of the address comprised of the interface's MAC address. Seems to be required, too, but I'm annoyed by the constant discussion of it in relation to enterprise networks. Third question, what is scope id for? Seems to be yet another term tossed around in relation to enterprise networks, especially when interconnecting them, but almost no explanation on the smaller home network level. Can I see a scope ID AND CIDR notation used together? I.e., fc00::4:0/120%6, or are scope IDs only supposed to be applied to a single /128 IPv6 address?

  Read the article

• Optimizing Disk I/O & RAID on Windows SQL Server 2005

  - by David

  I've been monitoring our SQL server for a while, and have noticed that I/O hits 100% every so often using Task Manager and Perfmon. I have normally been able to correlate this spike with SUSPENDED processes in SQL Server Management when I execute "exec sp_who2". The RAID controller is controlled by LSI MegaRAID Storage Manager. We have the following setup: System Drive (Windows) on RAID 1 with two 280GB drives SQL is on a RAID 10 (2 mirroed drives of 280GB in two different spans) This is a database that is hammered during the day, but is pretty inactive at night. The DB size is currently about 13GB, and is used by approximately 200 (and growing) users a day. I have a couple of ideas I'm toying around with: Checking for Indexes & reindexing some tables Adding an additional RAID 1 (with 2 new, smaller, HDs) and moving the SQL's Log Data File (LDF) onto the new RAID. For #2, my question is this: Would we really be increasing disk performance (IO) by moving data off of the RAID 10 onto a RAID 1? RAID 10 obviously has better performance than RAID 1. Furthermore, SQL must write to the transaction logs before writing to the database. But on the flip side, we'll be reducing both the size of the disks as well as the amount of data written to the RAID 10, which is where all of the "meat" is - thereby increasing that RAID's performance for read requests. Is there any way to find out what our current limiting factor is? (The drives vs. the RAID Controller)? If the limiting factor is the drives, then maybe adding the additional RAID 1 makes sense. But if the limiting factor is the Controller itself, then I think we're approaching this thing wrong. Finally, are we just wasting our time? Should we instead be focusing our efforts towards #1 (reindexing tables, reducing network latency where possible, etc...)?

  Read the article

• Tidy up old Windows Server Backup snapshots

  - by dty

  Hi, I'm running wbadmin from a scheduled job, backing up my C: and D: drives to my E: and (I believe!) including the system state: wbadmin start backup -backuptarget:e: -include:c:,d: -allCritical -noVerify -quiet I'd like to delete old backups, but I'm concerned that all the information I can find says to use wbadmin to delete old system state backups, and vssadmin to delete other backups. As far as I know, my backups ARE system state backups, but are using VSS on E: for storage, so I'm worried about trying either of these techniques for fear of losing all my backups. This is a home network, so I don't have a spare server to test this on. I'm also happy to simply restrict the space used on E:, but I can't make sense of the difference between the /for and /on parameters of the relevant vssadmin command. For reference, here's the output of vssadmin show shadows: Contents of shadow copy set ID: {xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx} Contained 1 shadow copies at creation time: 07/01/2011 08:12:05 Shadow Copy ID: {xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx} Original Volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Volume: \\?\GLOBALROOT\Device\HarddiskVolumeShadowCopy83 Originating Machine: x.y.com Service Machine: x.y.com Provider: 'Microsoft Software Shadow Copy provider 1.0' Type: DataVolumeRollback Attributes: Persistent, No auto release, No writers, Differential [... repeated a lot...] vssadmin show shadowstorage: Shadow Copy Storage association For volume: (C:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (C:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 0 B Allocated Shadow Copy Storage space: 0 B Maximum Shadow Copy Storage space: 5.859 GB Shadow Copy Storage association For volume: (D:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (D:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 0 B Allocated Shadow Copy Storage space: 0 B Maximum Shadow Copy Storage space: 40.317 GB Shadow Copy Storage association For volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Shadow Copy Storage volume: (E:)\\?\Volume{xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx}\ Used Shadow Copy Storage space: 168.284 GB Allocated Shadow Copy Storage space: 171.15 GB Maximum Shadow Copy Storage space: UNBOUNDED wbadmin get versions: Backup time: 07/01/2011 03:00 Backup target: 1394/USB Disk labeled xxxxxxxxx(E:) Version identifier: 01/07/2011-03:00 Can Recover: Volume(s), File(s), Application(s), Bare Metal Recovery, System State [... repeated a lot...]

  Read the article

• How does one make sure or even guarantee server time are sync correctly between dozens of servers across multiple datacenter on different location?

  - by forestclown

  Currently our web applications contain a logic to check if the data sent to the web server is expired or not by comparing the timestamp of the data with the date/time of the server. Everything goes will, until some dude from data center accidentally modify one of the web server date/time and causes some disruptions in our web services. My managers are of course not happy with this, and said we shouldn't use timestamp to check expiry in the first place...anyway.... Network Time Protocol is implemented, because of data centers are spread across different continents so we have one NTP server in each data center. The servers within the data center will have cron jobs to check against the time with their NTP server from the same data center. If time is out of sync it will auto update the server date/time. But then with our managers not happy with it, and think it could still easily causes the same problem. e.g. what if someone accidentally modify the NTP date/time? what if all the NTP servers are out of sync with each other? which NTP servers we can really trust? and blah blah.. So my questions are: What are the current practice to sync date/time between servers across multiple data centers or locations? How does one manages time stamp between web apps? e.g. Server A send data (contain timestamp of Server A) to Server B (compare timestamp between Server B and the timestamp from the data to see if it has expired or not. This is to avoid HTTP replay) Should we really not use timestamp check? Thanks & Best Regards

  Read the article

• Pinging switch results in alternating high/low response times

  - by Paul Pringle

  We have two switches that are behaving strangely. When I ping them the responses alternate between high and low results: C:\Users\paul>ping sw-linksys1 -t Pinging sw-linksys1.sep.com [172.16.254.235] with 32 bytes of data: Reply from 172.16.254.235: bytes=32 time=39ms TTL=64 Reply from 172.16.254.235: bytes=32 time=154ms TTL=64 Reply from 172.16.254.235: bytes=32 time=2ms TTL=64 Reply from 172.16.254.235: bytes=32 time=142ms TTL=64 Reply from 172.16.254.235: bytes=32 time=2ms TTL=64 Reply from 172.16.254.235: bytes=32 time=143ms TTL=64 Reply from 172.16.254.235: bytes=32 time=2ms TTL=64 Reply from 172.16.254.235: bytes=32 time=146ms TTL=64 Reply from 172.16.254.235: bytes=32 time=2ms TTL=64 Reply from 172.16.254.235: bytes=32 time=152ms TTL=64 Reply from 172.16.254.235: bytes=32 time=2ms TTL=64 Reply from 172.16.254.235: bytes=32 time=153ms TTL=64 Reply from 172.16.254.235: bytes=32 time=2ms TTL=64 Reply from 172.16.254.235: bytes=32 time=153ms TTL=64 Reply from 172.16.254.235: bytes=32 time=2ms TTL=64 Other switches in the network behave normally. I've rebooted the switches, but the behavior still is there with the ping. Any ideas on how to troubleshoot this? Thanks!

  Read the article

• pppd disconnects from 3G, doesn't reconnect, w/ persist set

  - by bytenik

  I am trying to configure pppd to connect to a 3G network (Sprint, in this case) and then stay connected, reconnecting automatically if the remote connection is terminated. I have enabled the persist option. My configuration file is as follows: hide-password noauth connect "/usr/sbin/chat -v -f /etc/chatscripts/cellular" debug /dev/cell 921600 defaultroute noipdefault user " " persist maxfail 0 lcp-echo-failure 10 lcp-echo-interval 60 holdoff 5 However, when the peer disconnects the connection, pppd often waits a long time (substantially more than my holdoff) to reconnect the modem -- if it ever reconnects at all! An example log showing this: May 23 05:17:24 00270e0a8888 pppd[2408]: rcvd [LCP TermReq id=0x26] May 23 05:17:24 00270e0a8888 pppd[2408]: LCP terminated by peer May 23 05:17:24 00270e0a8888 pppd[2408]: Connect time 60.1 minutes. May 23 05:17:24 00270e0a8888 pppd[2408]: Sent 0 bytes, received 0 bytes. May 23 05:17:24 00270e0a8888 pppd[2408]: Script /etc/ppp/ip-down started (pid 2456) May 23 05:17:24 00270e0a8888 pppd[2408]: sent [LCP TermAck id=0x26] May 23 05:17:24 00270e0a8888 pppd[2408]: Script /etc/ppp/ip-down finished (pid 2456), status = 0x0 May 23 05:17:24 00270e0a8888 pppd[2408]: Hangup (SIGHUP) May 23 05:17:24 00270e0a8888 pppd[2408]: Modem hangup May 23 05:17:24 00270e0a8888 pppd[2408]: Connection terminated. May 23 05:17:24 00270e0a8888 pppd[2408]: Terminating on signal 15 May 23 05:17:24 00270e0a8888 pppd[2408]: Exit. May 23 06:08:07 00270e0a8888 pppd[2500]: pppd 2.4.5 started by root, uid 0 May 23 06:08:10 00270e0a8888 pppd[2500]: Script /usr/sbin/chat -v -f /etc/chatscripts/cellular finished (pid 2530), status = 0x0 May 23 06:08:10 00270e0a8888 pppd[2500]: Serial connection established. May 23 06:08:10 00270e0a8888 pppd[2500]: using channel 11 The disconnect at the request of the peer occurs at 5:17, but the reconnect didn't happen until 6:08. I had a friend monitoring the server so I'm not certain that this wasn't a manual reconnection. Either way, it either took almost an hour to reconnect or never reconnected. Shouldn't persist + holdoff 5 cause this to automatically reconnect after 5 seconds of the link terminating?

  Read the article

• What are the most important aspects to consider when choosing a SAN for a small office virtualizatio

  - by Prof. Moriarty

  I am in the process of consolidating 6 physical servers running 6 different operating system flavors (don't ask) into two identical physical servers (Dell PowerEdge 2900), using the free VMware ESXi 4.0 platform. We will install an iSCSI SAN over a 1GbE network, and store all virtual machine images on the SAN. Each physical server would run 3 VMs, and in the case of a physical server failure, we would manually switch over the other 3. These are all internal servers, while important, they can tolerate some amount of downtime (say <1h) to keep cost and complexity associated with HA down. I now need to choose the SAN to be used for the setup, on a low budget. We currently have about 2TB of data, but of course I want to able to grow, do backups of VM snapshots on other drives and remove them to a different location, etc. So what I would like to know is: Which are the must have features for this setup, without which using a SAN is not worth it? We are mostly a Dell shop, so I have been looking at the EqualLogic PS4000E High Availability model. Any opinions, anecdotes, bad experiences with this model? (This is one of the few models which could accomodate our existing disks from the physical servers.) If you can recommend something that is not Dell, but it has better value, I would most definitely consider it. Caveats, things to look out for?

  Read the article

• IIS 7.5 stops serving requests for no apparent reason

  - by Steffen

  We're running a site on 4 virtual Win 2008 R2 64 bit servers. This is the only site on the IIS, and we use Windows Network Load Balancing to share the load between our 4 virtual servers. We've used these virtual servers for approximately a week, and we're starting to see some issues. For no apparent reason the IIS stops serving pages, and doesn't even respond with an error. So upon requesting a page from the server, the browser just waits infinitely (or until it decides to give up clientside) Sometimes an iisreset fixes the issue, other times we have to reboot the entire virtual server. There are no traces in the eventlog of why this happens, and there's no traces in our applications exception log neither. Furthermore this happens even when there's a very small load on the server, so it doesn't seem to be because it's flooded with requests. So frankly I'm at a loss here - I have no idea where to start debugging this issue :-( I'm quite certain we never had these issues on our physical servers, however they were running Win 2003 32bit, so there are quite a few differences between them and the virtual ones. (Which obviously makes it difficult to tell what exactly causes this)

  Read the article

• Inconsistent SMTP Access

  - by Mike Hanson

  I have a mail server setup on Windows Server 2008. All was working fine, until I wanted to map a drive on the server so that I can access files on another machine. Windows prompted me to configure Network Discovery, which I did with the "Home/Office" option rather than "Public". After that, several access points that worked before stopped working, like VNC, SMTP, etc. After reinstalling those packages, things appeared to be working again. Unfortunately, problems have returned with my SMTP server. I can use an web-based SMTP tester, and it connects in 62msec (as expected). However, if I telnet from my machine on the same LAN, it takes more than 20 seconds to connect! When I try to send messages from Outlook, it times out entirely with the message: Sending' reported error (0x80042109) : 'Outlook cannot connect to your outgoing (SMTP) e-mail server. If you continue to receive this message, contact your server administrator or Internet service provider (ISP).' I've checked the firewall settings, I've tried configuring it to use port 587 instead of 25, but nothing gets around this problem. Does any have any useful insights? Thanks in advance!

  Read the article

• Is this processor burned?

  - by Jhonnytunes

  I've recently exchange the processors in two PCChips boards. Both boards are LGA775. Board A is P17G(Pentium 4 HyperThreading 3GHz) and board B is P49G(Pentium Dual Core 3GHz). I use board A to watch videos, and some of them are 3GB size and this is why I exchanged the CPU. I installed Dual Core in board A and it worked out of the box, now 3GB videos use 5% of CPU instead of 50%. When I installed the pentium in the board B, I forgot to connect the 4pin power and, when i powered on the PC, the CPU fan stay off. Then, I connected all right this time, and now the board doesnt show video. I think the CPU is not working but im not sure about that. The PC turns on and the HD spins, the CPU fan spins, network socket blinking, but not video and case power led is neither blinking. I tried with other PSU and everything was the same. I figure out that CPU have that paste above. IDK really what's happening, I hope I dont have to buy another CPU. Is it Burned?

  Read the article

• Port forwarding + shared connection with Ubuntu

  - by Joey Adams

  Because my wireless router's ethernet ports are defective, I set up a shared wireless connection from my laptop (which has wifi) to my eMac (which does not) via a crossover ethernet cable. The laptop is behind a router as 192.168.1.131, and the eMac is behind the laptop as 10.42.43.1 . The laptop is running Ubuntu 9.10 (Karmic). I achieved the shared connection through NetworkManager Applet. I right-clicked on the network icon at the topright, went to Edit Connections, selected the Wired connection named "Auto eth0", clicked "Edit...", went to the "IPv4 Settings" tab, and selected the Method "Shared to other computers". The eMac can now access the Internet. Now I want to enable port forwarding. There's a game I want to play that needs port 6112 forwarded (both TCP and UDP) in order to host games. I set up the router to enable port forwarding for 192.168.1.131 (the laptop), but port forwarding still isn't available on the eMac. I suppose I need to pretend my laptop is a router and configure port forwarding on it, indicating that incoming connections to the laptop (192.168.1.131) should be forwarded to the eMac on the shared connection (10.42.43.1 ). Thus, packets coming into the router on port 6112 would be redirected to the laptop (by the router), then to the eMac (by the laptop). My question is, how would I do that on Ubuntu (in light of NetworkManager's presence)? Also, if I can't get this to work, does anyone mind hosting a comp stomp? :D

  Read the article

• AWS VPC public web application connecting to database via VPN

  - by Chris

  What I am trying to do is set up a web application that is public facing but makes calls to a database that is on an internal network. I have been trying to set up an AWS VPC with a public subnet, private subnet, and hardware VPN access but I can't seem to get it to work. Can someone help me understand what the process flow here should be? My understanding is that I need a public subnet to handle the website requests and then a private subnet to connect to the VPN but what I do not understand is how to send requests down the chain and get the response. Basically what I am asking is how can I query the database via VPN from that public website? I've tried during rout forwarding but I can't successfully complete the process. Does anyone have any advice on something I can read on this subject or an FAQ on setting something like this up? Is it even possible? I'm out of my league here, this is not my area of expertise but I'm being asked to solve this problem. Any help would be appreciated. Thanks

  Read the article

• Grant HTTP access based on unix user group

  - by Sander Marechal

  Is it possible to grant network access or HTTP access based on a user's group? At my company we want to set up an internal composer server using Satis to manage packages for the projects we write (e.g. on repository.mycompany.com), with the packages themselves in our SVN server (svn.mycompany.com). We have several webservers with many different users on them. Some users should be able to reach the composer and SVN server. Some should not. Users that should be able to reach these servers all belong to the same group. How can I set up Apache on the Composer and SVN server to only grant access to those users in that group? Alternatively, can I set up the webservers in such a way that only users from that group are able to make a connection to our Composer and SVN servers? The best thing we have come up with so far is using SSL client certificates. We simply place a client certificate on all servers which can be used to access Composer and SVN. Only the right usergroup will have read access to the certificate. A bit clunky but it may work. But I'm looking for something better.

  Read the article

• Possible to host CentOS netinstall files on a local HTTP/FTP?

  - by garlicman

  I'm running XenServer on an Dell R610 and am running into a catch-22. During install from DVD, CentOS can't find the DVD package catalogue. It's a reported error for some, XenServer + CentOS6 + DVD install in some hardware configurations = failed install. Yes, I checked the MD5 and let the disc test pass. In every reported case, the netinstall was the solution. The issue is my net access is required to go through a web proxy that prompts before you can download a file. This naturally breaks any download automation. I've been waiting on our IT to put in an exception rule to allow my lab to bypass the prompt, but it's been over 3 weeks now and they don't seem responsive. (I've been working on this a day or two a week) I want to try and host the netinstall files local in my Xen network. Right now I only have a bunch of Windows based VMs, CentOS won't install so I don't have any Linux tools. I had tried simply hosting all the DVD contents off one of the Windows servers using Mongoose. (I didn't want to setup IIS) I copied them to a hosted sub-directory similar to all the mirrors out there (e.g. http:///centos/6.2/os/i386/) with no auth or anything. Then in the netinstall I correctly pointed to it. I now realize just copying the DVD files over won't work. The repodata will point to a local device, not the site I'm hosting. (e.g. the DVD repodata includes xml that points to where the packages are) Clearly I'm hosting them over HTTP, not from a DVD. Is there an easy way to sort this out? I'm just trying to install CentOS6 on Xen. If there's a turnkey downloadable Xen image with CentOS 6.2 on it, or a downloadable repo image, I'll take that too! Thank you in advance!

  Read the article

• RDP Connection to Windows 7 stays really slow

  - by Pavlo

  I have an Issue with connecting to Windows 7 via RDP. I can open an RDP Session, but regardless of any settings, the responce times are really long. This in particulary is the case when opening a web page in a browser. I've tried IE, Firefox and Google Chrome. I also use RDP connection to a Windows 2008 Server from the same client machine, and the speed is very normal with all features turned on. We have Gigabit Ethernet here. So I think it can not be the client's fault. What concerns Windows 7 Machine, I've tried shutting all the sraphic features off and turning the color levels to 256 colors. Result - the same. If I work locally on the machine - I can not see any lags. What else have I tried: Using old RDP 5 Client from Microsoft Setting network autotuninglevel as seen here Do You have some ideas? Thanks in advance! Update the problem seems to be with rendering window contents. All the window borders and pannes are rendered pretty quickly, but the content shows up very slowly. Also mouse movements are recognised by the Win 7 box only after some period. Are there some hidden settings in the RDP, where one could turn some advanced features off or turn some caching on? I use Bitmap Caching, but this apparently doesn't help.

  Read the article

• Can't connect to MySQL on CentOS 5 Error 13 - Permission Denied

  - by abszero

  Ok, I have an install of CentOS 5 running as a GuestOS in VirtualBox. The network card for the Cent box is bridged with that of my host OS so that the boxes can see each other. Cent has an IP of 192.168.1.108 and my Host box has an IP of .104. Everything, with regard to networking, seems to be working properly as I can access the Drupal install that is on the Cent box from a web browser on my host box by navigating to http://192.168.1.108 however when I try to configure the database for Drupal through the Drupal install interface I am getting the Can't connect to MySQL error. First I thought this might of been a Firewall issue so I stopped iptables but that had no effect. I thought maybe the user I had setup did not have access to the server so I tried root and that did not work. Searching on the net said that I needed to provide a bind-address parameter to my.cnf so I did that with no change. (As a side note the length of my my.cnf file was MUCH shorter than the ones presented online. In fact under mysqld all I have are datadir, socket, user, and bind-address. Is this normal or should the file be more verbose?) After a few hours of messing with permissions and such I tried using 'localhost' as the value for the database server, from my HOST OS, and the Drupal install kicked off without a problem. So while my issue is resolved I am curious as to why 'localhost' works and why 192.168.1.108 did not? Is there something i need to do to specifically access the MySQL box via the aforementioned IP? Thanks.

  Read the article

• How can I tell my dd-wrt router to use someone's Amazon Affiliates link when I point my browser to amazon.com?

  - by Michael Paul

  Here's what I'd like to do. Instead of a one-time donation to one of my favorite free tools (junecloud.com) I'd like to do what they suggest here and use their Amazon Affiliates link to do all my Amazon shopping. I shop at amazon once or twice a week, so this is a great way to let them earn lots of long-term cash without me dropping a dime. My thought was to go into my dd-wrt enabled router and tell it, "any time I go to amazon.com on any computer in the house, please go to http://www.amazon.com/gp/redirect.html?link_code=ur2&tag=junecloud-20&camp=1789&creative=9325&location=%2F instead. (That URL simply redirects me to amazon.com but every purchase I make during that session is credited to JuneCloud.) Once logged into dd-wrt, I went to Services Services DNSMasq but I'm not really sure how to get it to work from there, or if it's even possible. I know I can redirect IP addresses, but I'm looking to redirect someone on my network from amazon.com to the special amazon affiliate code link. Hope that's clear. Thanks for any replies!

  Read the article

• Some guest networking and VMware Tools functionality broken with Sprint SmartView on the host

  - by Mads

  Using VMware Workstation 6.5.3 on Vista 64-bit. I started having problems with VMware networking about 6 months ago after upgrades to Sprint SmartView. I did not have problems previously, but I don't know if that is because I was lucky. The main symptoms of the problem when SmartView is installed are: I can no longer drag files from the host to copy them to the guest. When they are dragged, the disallowed cursor (the circle with a slash) shows in the guest. If I try to enable shared folders in the guest while it is running, I will not be able to see the shared files and will be informed that networking is not working. I can still ping guests from the host and I can still access network services via NAT most of the time when connected via my USB broadband adapter. When I configure shared folders so they are "always enabled" (with a mapped drive), I can access files on the via the mapped folders. I can also copy the file on the host and then paste it in the guest, as was suggested in some other threads concerning drag-and-drop problems that I found. The VMware Tools icon is showing in all cases and I don't see any obvious errors in the host's event viewer. If I uninstall SmartView, the problems disappear. If SmartView (current version is 2.28.0082) is reinstalled I will experience the same problems. I have tried uninstalling/reinstalling VMware and SmartView in various ways but it appears tha these problems are consistent when SmartView is installed (not just when it is running or connected, but when it is present on the system). I'm wondering if this is a combination of software (WS 6.5.3, Vista64, and SmartView) that works for other people, which would indicate a problem that is peculiar to my configuration.

  Read the article

• How to debug a kernel created using ubuntu-vm-builder?

  - by user265592

  Aim: Trying to perform a code walkthrough of what functions are getting called for sending and receiving packets over the network. I am building a kernel and using gdb for debugging/ tracing purposes. I have build a vm using the following command : time sudo ubuntu-vm-builder qemu precise --arch 'amd64' --mem '1024' --rootsize '4096' --swapsize '1024' --kernel-flavour 'generic' --hostname 'ubuntu' --components 'main' --name 'Bob' --user 'ubuntu' --pass 'ubuntu' --bridge 'br0' --libvirt 'qemu:///system' And I can run the VM successfully in qemu using the following command: qemu-system-x86_64 -smp 1 -drive file=tmpGgEOzK.qcow2 "$@" -net nic -net user -serial stdio -redir tcp:2222::22 Now, I want to debug the kernel using gdb. For this I need an executable with debug symbols(vmlinux), which apparently I don't have, as the vm-builder never asked for any such options and simply created a .qcow2 file. Question 1: Am I taking the correct approach to solve the problem and is there an easier way to do it? Question 2: Is there a way to debug this kernel using GDB? P.S: I don't have hardware support for KVM. Please correct me if I am wrong. Thanks.

  Read the article

• File Sync Solution for Batch Processing (ETL)

  - by KenFar

  I'm looking for a slightly different kind of sync utility - not one designed to keep two directories identical, but rather one intended to keep files flowing from one host to another. The context is a data warehouse that currently has a custom-developed solution that moves 10,000 files a day, some of which are 1+ gbytes gzipped files, between linux servers via ssh. Files are produced by the extract process, then moved to the transform server where a transform daemon is waiting to pick them up. The same process happens between transform & load. Once the files are moved they are typically archived on the source for a week, and the downstream process likewise moves them to temp then archive as it consumes them. So, my requirements & desires: It is never used to refresh updated files - only used to deliver new files. Because it's delivering files to downstream processes - it needs to rename the file once done so that a partial file doesn't get picked up. In order to simplify recovery, it should keep a copy of the source files - but rename them or move them to another directory. If the transfer fails (network down, file system full, permissions, file locked, etc), then it should retry periodically - and never fail in a non-recoverable way, or a way that sends the file twice or never sends the file. Should be able to copy files to 2+ destinations. Should have a consolidated log so that it's easy to find problems Should have an optional checksum feature Any recommendations? Can Unison do this well?

  Read the article

• How can you connect to a SQL Server not on your domain?

  - by scotty2012

  I have a test machine that's not allowed on our domain because we are testing corporately unsupported applications (SQL 2008 and Server 2008). I want to use management studio to connect to the SQL2008 server but can't get it working. I have authentication set to mixed-mode, I've checked 'allow remote connections to this server', but when I try to access it, I get the error A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 53) Since it says the provider is Named Pipes, I enabled Named Pipes on the server, but still no dice. I've tried connecting to the system name, the IP, the system name\instance and IP\instance, all to no avail. Is what I'm trying to do not possible? Edit: Well, through some basic troubleshooting, I've found that I can't ping the server from my client computer, but I can ping the client computer from the server? They are both plugged into the same switch, and are sitting next to each other. The windows firewall on the server is turned on, is there some specific settings I need to enable? DAH! So it was the firewall blocking me. How can I enable the firewall and still connect?

  Read the article

< Previous Page | 1049 1050 1051 1052 1053 1054 1055 1056 1057 1058 1059 1060  | Next Page >