Search Results

Search found 4739 results on 190 pages for 'black nm'.

Page 108/190 | < Previous Page | 104 105 106 107 108 109 110 111 112 113 114 115  | Next Page >

• DIsable my nv video card driver in linux

  - by Dahaka Wang

  I'm trying to passthrough my nv video card to my domU, but I could not bind my video card to the pciback driver I only have one video card with the pci number 0000:03:00.0, so I used the following command echo -n "0000:03:00.0" > /sys/bus/pci/drivers/nouveau/bind to unbind the nouveau driver from my video card. The screen went black because I have forcefully removed the video driver, therefore I ssh'd into the computer to run further commands I ran: echo -n "0000:03:00.0" > /sys/bus/pci/drivers/pciback/bind to try to bind it to my pciback driver, but I got: bash: echo: write error: No such device I found out that this was the message shown when trying to bind a PCI device which is already bound. Therefore, I think that something was still using my video card Can anyone help me out? Thanks a lot!

  Read the article

• youtube video playing without sound when downloaded?

  - by On a serious note

  I have been looking for this since a long long time. I have downloaded a few videos from you-tube using IDM(all mp4). When I opened the video in VLC media player,a black screen appeared and started flickering.The video just does not start. What all I things I did-: updated my VLC Reinstalled my VLC downloaded another media player(wondershare--very very beautiful i must say).It played the video but audio was missing. converted mp4 to flv and then played in both players,still no sound. Its very frustrating as I want to complete my tutorial series asap.FLV works well,but mp4s fall flat. What should I do?

  Read the article

• I hyperlinked a cell in excel 2003, formula issues?

  - by joseinsomniac

  I have a budget spreadsheet using excel 2003. I have My deposit, then all of my bills, the total, then a cell that has the difference(between the amount of deposit and the total of the bills). The difference cell numbers turn red when I dont have enough money (deposit vs bill total). I hyperlinked the difference cell to a checkbook register spreadsheet so I can track where all my extra money went(reconsile receipts daily). When hyperlinked the numbers are blue. I need the numbers to stay black(when above 0.00) and stay red (when the numbers are below 0.00) and not change after the link has been clicked on. Also if the link has not been clicked on, and the numbers are red, the font is smaller, even though the toolbar shows the font size hasnt changed. After I click on it and go back to the budget sheet, its the size it should be. Any Ideas? Thanks!

  Read the article

• Samsung TV connected to PC for Powerpoint

  - by Skaughty

  I have a 42" Samsung LCD TV connected to a Dell computer with a PCI Radion 9000 via a 35' VGA cable. It's purpose is to run power point presentations over the TV for our retail store. I have tried every combination of button clicking on the video card options, and everything on the TV, and I still get black bars on the top and bottom of the image. It looks like I am watching a old wide screen movie on a full screen TV. The TV's suggested resolution is 1024x768, and that is what the output is set to. I have tried this with a nVida PCI card as well with the same results.

  Read the article

• Is Protune for video only or may be used for photo too?

  - by Green

  I have Hero3+ Black Edition. I can't understand if Protune is for video only or may be applied for photos? The manual says it is both for video and for photo (page 35): High-Quality Image Capture Protune’s high data rate captures images with less compression, giving content creators higher quality for professional productions. Film/TV Rate Standard While shooting in Protune, you have the option of recording video in cinema quality 24 fps to easily intercut GoPro content with other source media without the need to perform fps conversion. But at the same time their site says that Protune is for video only: To record Protune footage, you’ll need to turn Protune ON in your camera’s settings menu. What for is Protune? Photo? Video? Or both?

  Read the article

• How do I free some disk space so Ubuntu will boot again?

  - by Omkant

  I have installed Windows and Ubuntu side by side. I created a 10GB partition for the Ubuntu installation. During the two months I've been using Ubuntu I have installed some software. Now it's not starting. When I boot up it says that there is no diskspace so it could not be started . What can i do now? When I boot up all I get is a black screen terminal with a $. Please help me with a command to uninstall some programs and start using Ubuntu or any other way to get rid of this message.

  Read the article

• My computer won't go into standby or hibernate

  - by Thomas B.

  Hi. I have a problem that I first noticed yesterday. Whenever I would press the half moon standby button on my keyboard, my computer would go to sleep. I also have a shortcut on my desktop configured to put my computer into hibernate. But now whenever I try to put my pc in sleep or hibernate mode, my monitor goes black for a few seconds but then comes back on at the login screen. I haven't installed or changed anything other than create a couple logical partitions in the hfs+ filesystem. (still in the process of trying to triple-boot) Any help would be great, but for now I'm going to bed. Will check back in the morning.

  Read the article

• Computer only booting after POWER ON/OFF 10 times or more?

  - by Jan Gressmann

  Hi fellow geeks, recently my computer started to behave like an old car and won't start up anymore unless I flip the power switch repeatedly. What happens when I power it on: CPU fans spins briefly and very slowly, then it stops Same with GPU fan No BIOS beeps or HDD activity Screen stays black After turning it on and off for like 10 times, it'll eventually boot like normal and run smooth without any problems what-so-ever. But I'm worried it might eventually die completely. Anyone know the most common cause of this? Maybe I should just leave the computer powered on? :)

  Read the article

• Windows 8 taking 4+ mins to shutdown

  - by arnab321

  I did a fresh installation of Windows 8 64 bit, build 9200 (released on aug 16th). I installed the drivers and some basic softwares like NetBeans, mingw, iis server and php. For the first few times, it was restarting normally. But then at shutdown, it would show the shutdown screen for some seconds and then turn black for about 4 mins (similar to what happens at hibernation). I disabled the "fast startup" option in power options, but the problem still persists. Windows 7 and Ubuntu shut down normally. specs: 4gb ram, 750 gb sata hdd, solved by installing Windows Updates released during October. It was a serious bug in the OS, afaik. Now even hibernate takes upto 30 secs max. Still, win 8 is too buggy for release.

  Read the article

• Explorer.exe - No such interface supported and other issues

  - by tom

  The problem started when I uninstalled my ATI graphics driver and i used a driver cleaner. After i restarted win7 and it got to POST the screen just went completely blank. So i Used system restore from the repair menu to get back on. I found out that if I ran chkdsk the display just goes black after restart on startup and i have to use system restore to get back on windows7 not sure why this is. When i right click desktop and choose 'Screen Resolution' it says No such interface supported. Also when I click items such as device manager in the windows explorer it does not do anything. I have tried re-registering the DLLS but that did not do anything.

  Read the article

• Ubuntu 9.10 freezes when HDMI port is connected

  - by Felipe Hummel

  I have a Sony Vaio FW350 with a HDMI output. I'm trying to use it under Ubuntu 9.10 with a LG LCD monitor 21,5'. The laptop has a Intel 4500 video card. I've tried two approaches: Boot the laptop with the HDMI cable connected and monitor turned on. Result: LCD Monitor keeps turned on but the whole screen is black and Ubuntu do not seem to be initializing. Boot Ubuntu until the end. I then connect the HDMI cable into the Laptop. The mouse and the whole system freezes. In both cases the only way to turn off the laptop is holding the power button. I've looked around the internet for similar problems, but only found workarounds for the same problem with VGA input, not HDMI. I also tried to use metacity before connecting the cable, but still got the same result. Any hints?

  Read the article

• Mac OS X Lion (10.7.3) Virtual Machine?

  - by Ben Hooper

  I have been looking into this for a while and have attempted quite a few "solutions" (hackintosh boot images, universal unlockers, etc) before I gave in and asked for help. I know this is extremely difficult to accomplish, especially with an AMD CPU, but it has been done and it can't hurt to ask. Question Does anyone know of any way to actually get Mac OS X Lion (10.7.3) to boot in VMware Workstation 8.0.2? I know that Mac OS X is heavily dependant on hardware configuration, so I will post my PC's hardware below, if it helps. As far as I know it's only reliant on the CPU, but I will post it all just in case. PC Hardware Motherboard: ASUS M4A77T CPU: AMD Phenom II x4 955 Black Edition Graphics Card: Palit Sonic Platinum nVIDIA Geforce GTX 460 Memory: G-Skill [RipjawsX F3-12800CL9D-8GBXL] 8GB PSU: Arctic Power 700(W) Hard Drive: SAMSUNG HD204UI 2TB Thanks in advance. :)

  Read the article

• ATI Radeon 4350 lower resolutions do not fill screen in Windows 7

  - by rlandster

  I have a new Windows 7 64-bit machine with an ATI HD4350 card. The card is connected via VGA (DSUB) to a SyncMaster 205 BW LCD monitor. If I set the resolution to 1680x1050 the LCD screen is completely filled and everything looks fine. But, if I try to set the resolution to 1280x768 (my preferred resolution) only about 2/3 of the monitor screen is used. There are large black bars above and below the image (but not on the sides). I have successfully used this monitor at the 1280x768 resolution for many years without this problem (albeit in Windows XP and a different video card). Can anyone suggest how I can get adjust things so that the entire screen is used at the 1280x768 resolution?

  Read the article

• Converting an external hard drive to internal

  - by Nathan DeWitt

  I have a WD Elements 1 TB external drive. I'm in a pinch and I need an internal SATA drive. How do I find out if the drive in here is actually a SATA drive? Edit: The WD Elements is a really nice external drive. I gently pried open the top and slid out a 1 TB Caviar Green hard drive. There were four black rubber brackets that slid off easily. One screw removed the SATA -- USB, and then I slid it into my computer.

  Read the article

• New Windows 7 Install Crashing

  - by bobber205

  One big reboot crash and one smaller crash already, 15 minutes in. Did a basic install of Windows 7, installed Chrome and Firefox. I had just finished loading up my gmail account in Chrome/Firefox to show the speed difference and we'd thought it would be hilarious to see how slow IE8 was. :P Just about as IE8 was done opening, the computer's screen goes black. After a restart and a couple minutes, Explorer crashes as well. What is going on? This install is only 15-20 minutes old. :P

  Read the article

• How can one make the title bar text/buttons have better contrast on dark colors in Windows 8?

  - by zeel

  When Windows 8 color setting are set to a very dark color, such as black or navy blue, the title bar text and the minimize/maximize buttons are nearly invisible. This makes dark colors difficult to work with. In Windows 7 there was an advanced color options, this is gone in 8. The registry keys associated with this seem to still be present, but they have no effect. Is there a way to change this? Or a third party application that can do it? I don't want to use the ugly high contrast theme, I want to use the nice Win 8 theme with a dark color.

  Read the article

• Can't unlock locked screen, in Ubuntu 12

  - by Camille Goudeseune

  After locking the screen (with a keystroke bound to xlock -nice 8 -mode blank), I can unlock the screen as expected, but only within a few minutes. After being locked overnight, when I hit a key (even Ctrl+Alt combos), the screen stays black with just a brief white flash across the middle of both monitors. The workaround is to ssh in from another host and restart X. Some months ago, this happened every few weeks. By now it happens almost every morning. How do I even start to diagnose this? What might I look for in log files? (The intermittency is particularly troubling.) Failing that, is there an alternative to xlock aka xlockmore? Hardware: 3-year-old HP minitower, GEForce 9800 GT, two Asus LCD monitors. Software: Ubuntu 12.04.2 LTS. Window manager awesome-wm. NVidia driver 304.88. XLock version xlockmore-5.31.

  Read the article

• plugging in a 3.3V 50pin laptop HDD to USB?

  - by barlop

  I have a 50pin laptop hard drive. 1.8" wide. This 50pin connector concerns me.. Even if I get an adaptor, How can I know which side of the connector takes the power? I don't want to plug it in the wrong way. And I don't have n adaptor.. Could people link me to adaptors too. but main question is, which side to plug it in when I get the adaptor. I want to be sure. I do not want to blow the hdd. For the 3.3V I have a plan. Connecting green and black and using the orange cable(3.3v) to feed power. I am not too worried about that bit. But as I said.. Main thing is I want to know which side is 3.3V hard drive is MK6006GAH

  Read the article

• TrueCrypt - "Warning! Password locked: Fixed disk0" error message on boot

  - by Tibi

  TrueCrypt - "Warning! Password locked: Fixed disk0" error message on boot. When i start my laptop (Acer TravelMate 2410). after the starting memory check, the screen goes full black, and a message appears for about 3 seconds: Warning! Password locked: Fixed disk0 and after that, disappears, and next message comes out: Operating System Not Found and all stops here. Windows Xp was installed on it, before this came. TrueCrypt cd (witch was made during the process of full encryption) is not working, not in restoring MBR, no even in decrypting my drive - completely useless. Note: I detected some short of boot sector errors (i dont know the amount) on my drive before this happened. Please, i would greatfully thank every comment, or suggestion, because my computer is unusable now. The HDD is a Samsung HDD, 160Gb. Other preferences: Acer TravelMate 2410 Notebook, 2 Gb RAM, 1500 Mhz Intel Celeron M processor. Regards

  Read the article

• Which PSU should one chose? The biggest is the best?

  - by Shiki

  I'm fully aware of PSU's "Active PFC" and that they won't consume the written W all the time. (Makes sense). But now I'm before a PSU replacement (Guys: NEVER buy a Chieftec. Seriously.) The question is: If one can get a bigger one (in my case 750W and 650W) ... should that person go for the bigger one ? (The difference in price is not much). No, I don't think I'll soon use all that much. (Please help (if you want of course) to make the question more generic if the question is really not OK in this form. I've been wondering about this for a time already. In my case it would be XFX Black Edition Silver 750W and 650W) (Basically about "which one" I would go with XFX/Antec/something which comes with industry qualified parts. Like Duracell but in a PSU. :) But the performance is a different thing.)

  Read the article

• Dual Monitors don't turn off/sleep when they should

  - by Mario

  Details: Dual 25" monitors connected to HP Envy via HDMI and display port via DVI adapter. Power scheme is set up in high performance (Dim Display: Never - Turn Off Display: 15 mins - Computer Sleep: Never) Screensaver is set up to kick in after 10 mins of idle (which happens) 5 minutes later, the screensaver stops. The "Monitor Going to Sleep" notice appears on screen and monitors go to sleep briefly. All is well thus far. Suddenly, the Windows 7 alert sound when a device is unplugged is heard. Monitors then turn back on. Screens are black. Only the mouse cursor is displayed. Backlighting is back on. This only started happening after I obtained and connected the second 25" monitor a few days ago. However, I had a 24" in its place before, and this wasn't happening. Why is this happening and how do I correct this behavior? Thanks in advance.

  Read the article

• X58 RAID 10 - Am I forced to use Sata2?

  - by Avi

  I'm building a new dev computer. It will be running a few VMWare Worksation virtual machines. I was advised on Serverfault to use Raid10 for performance. Raid 10 uses 4 disks. I contacted my supplier who suggested a gigabyte X58A motherboard and 4 Western Digital Caviar black 6Gb/s disks. I have checked the spec for the X58A board, however, and it says: SATA 3Gb/s: RAID 0, RAID 1, RAID 5, and RAID 10 SATA 6Gb/s: RAID 0, and RAID 1. I'm losing half the bandwidth because I'm forced to use SATA2! What should I do?

  Read the article

• Image doesn't fill monitor when connected via HDMI

  - by russau

  Connecting a Dell Studio Slim to a Dell ST2210 21.5" monitor. The PC has a ATI Radeon HD 4350 video card. The video card has DVI and HDMI connections. When I connect with the DVI everything works fine. When I connect with the HMDI the image doesn't fill the screen, i.e. there's a approx 1 inch black border around the image. Win7 tells me the res is 1920x1080 (the native res of the monitor). Tried rebooting, no luck.

  Read the article

• DVI problem with LG L204WT

  - by Holgerwa

  I have a LG L204WT which has VGA and DVI connectors. Until recently, I have used the monitor via VGA, but now I have upgraded the graphics board and switched to DVI. The problem is that each time after the computer starts, the monitor either doesn't show anything (black screen, but doesn't go into standby) or the picture is distorted. I then switch the monitor off and on several times, and at some point it starts correctly and then I can work as usual. This only happens on startup. It is one out of 3 monitors, the other two work fine. It seems to me as if the monitor is not able to synchronize on the DVI signal and either shows a distorted picture or nothing at all. There are no settings in the monitor setup that would change anything. What could be the problem?

  Read the article

• IIS 7 Application Pools using a different amount of memory on multiple servers behind a load balancer

  - by Jim March

  We have 6 servers in a web farm behind an F5. There are approximately 25 AppPools on each of these servers. On servers 1 - 5 the apppools are consuming approx 500MB Private Bytes, and 5GB Virtual Bytes. On server 6 the apppools are consuming approx 800MB Private Bytes, and 8GB Virtual Bytes. I can not seem to figure out why we have this difference. The code is the exact same on each box. We replicate the apphost.config between the boxes, so the Appplication Configs are identical. The only difference seems to be that this box consumes more RAM, and in turn ends up using a lot more CPU. During Black Friday we observed the CPU on server 6 spiking to 100% and noticed that the % Memory Commit was also near 100%, while the rest of the farm was at closer to 50% utilization. Pulling the 6th server from the load balancer dropped CPU/Memory on the 6th server back to normal, and did not cause a noticeable strain on the other servers.

  Read the article

< Previous Page | 104 105 106 107 108 109 110 111 112 113 114 115  | Next Page >