Search Results

Search found 577 results on 24 pages for 'dmesg'.

Page 11/24 | < Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >

  • How to diagnose network speed drops

    - by Luis Alvarado
    Here is the image of System Monitor first: The graph shows the cycle the connection goes through. After 10 to 15 seconds it drops to 0 KB/S, then goes up to the Max speed (120 KB/S) then it repeats. dmesg shows the following during that time: [ 6066.757211] wlan0: send auth to 00:26:5a:b5:05:7b (try 1/3) [ 6066.804405] wlan0: authenticated [ 6066.804578] rt2800pci 0000:02:01.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 6066.805016] wlan0: associate with 00:26:5a:b5:05:7b (try 1/3) [ 6066.809218] wlan0: RX AssocResp from 00:26:5a:b5:05:7b (capab=0x431 status=0 aid=1) [ 6066.809581] wlan0: associated [ 6066.810203] bridge-eth0: disabling the bridge on dev down [ 6066.810239] bridge-eth0: down [ 6066.810254] bridge-eth0: detached [ 6066.810309] /dev/vmnet: open called by PID 1679 (vmnet-bridge) [ 6066.810322] /dev/vmnet: hub 0 does not exist, allocating memory. [ 6066.810355] /dev/vmnet: port on hub 0 successfully opened [ 6066.810366] bridge-wlan0: device is wireless, enabling SMAC [ 6066.810369] bridge-wlan0: up [ 6066.810372] bridge-wlan0: attached [ 6067.010285] userif-2: sent link down event. [ 6067.010290] userif-2: sent link up event. This also repeats with Wired or Wireless connections. How can I diagnose this changes in the network efficiently.

    Read the article

  • selinux permissive and type targeted

    - by krisdigitx
    i am running centos 6.2 recently i noticed that apache was running with selinux enabled # This file controls the state of SELinux on the system. # SELINUX= can take one of these three values: # enforcing - SELinux security policy is enforced. # permissive - SELinux prints warnings instead of enforcing. # disabled - No SELinux policy is loaded. SELINUX=Permissive # SELINUXTYPE= can take one of these two values: # targeted - Targeted processes are protected, # mls - Multi Level Security protection. SELINUXTYPE=targeted i noticed that these errors were coming on dmesg type=1400 audit(1354453732.704:9056368): avc: denied { name_connect } for pid=39006 comm="httpd" dest=11211 scontext=unconfined_u:system_r:httpd_t:s0 tcontext=system_u:object_r:memcache_port_t:s0 tclass=tcp_socket type=1400 audit(1354453735.777:9056369): avc: denied { name_connect } for pid=39046 comm="httpd" dest=6379 scontext=unconfined_u:system_r:httpd_t:s0 tcontext=system_u:object_r:port_t:s0 tclass=tcp_socket i then enabled /usr/sbin/setsebool httpd_can_network_connect=1 and this stopped the errors and also the webpages started to work. My question is if selinux is in permissive mode will selinuxtype=targeted enforce any polices? if not how did it solve the problem with apache as selinux was already in permissive mode?

    Read the article

  • Why does 'top' say my machine is only 50% idle?

    - by Chris Moore
    What's going on here? I'm running nothing on the system, iotop and iftop show the network and hard drive are both idle, and top (sorted by %CPU) shows nothing running. So why is the system only 50% idle? What's the other 50% waiting for? How can I find out? top - 12:01:05 up 3 days, 15:03, 1 user, load average: 6.00, 6.01, 6.05 Tasks: 179 total, 1 running, 178 sleeping, 0 stopped, 0 zombie Cpu(s): 0.7%us, 0.0%sy, 0.0%ni, 49.7%id, 49.7%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 2053996k total, 1992600k used, 61396k free, 81680k buffers Swap: 4092924k total, 10740k used, 4082184k free, 1338636k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1042 deb 20 0 21468 1412 1000 R 1 0.1 0:00.03 top 1 root 20 0 24188 1952 1152 S 0 0.1 0:01.44 init 2 root 20 0 0 0 0 S 0 0.0 0:00.05 kthreadd Update: dmesg shows the printer driver misbehaving: [28858.561847] cnijnetprn[1503]: segfault at 29 ip 00007f56cf3480f7 sp 00007fffb964ec30 error 4 in libcnnet.so.1.2.0[7f56cf345000+9000] [68851.187802] cnijnetprn[9180]: segfault at 29 ip 00007ffe7636a0f7 sp 00007fff9a8b1990 error 4 in libcnnet.so.1.2.0[7ffe76367000+9000] [155412.107826] cnijnetprn[19966]: segfault at 29 ip 00007fc31de770f7 sp 00007fffc03aa8e0 error 4 in libcnnet.so.1.2.0[7fc31de74000+9000] and also some issue with cp: [248041.172067] INFO: task cp:27488 blocked for more than 120 seconds. [248041.172071] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. [248041.172075] cp D ffffffff81805120 0 27488 27345 0x00000004 [248041.172080] ffff880078d57a38 0000000000000046 ffff880078d579d8 ffffffff81032a79 [248041.172085] ffff880078d57fd8 ffff880078d57fd8 ffff880078d57fd8 0000000000012a40 [248041.172090] ffff88007b818000 ffff880069acc560 ffff880078d57a18 ffff88007f8532c0 [248041.172095] Call Trace: [248041.172104] [<ffffffff81032a79>] ? default_spin_lock_flags+0x9/0x10 [248041.172109] [<ffffffff8110a360>] ? __lock_page+0x70/0x70 [248041.172114] [<ffffffff815f0ecf>] schedule+0x3f/0x60 I did try copying something to the USB stick that's plugged into the router and mounted onto this computer using mount.cifs. That almost always causes everything to lock up, so I'm guessing that's the problem. I'll reboot and stop using mount.cifs.

    Read the article

  • VFS: file-max limit 1231582 reached

    - by Rick Koshi
    I'm running a Linux 2.6.36 kernel, and I'm seeing some random errors. Things like ls: error while loading shared libraries: libpthread.so.0: cannot open shared object file: Error 23 Yes, my system can't consistently run an 'ls' command. :( I note several errors in my dmesg output: # dmesg | tail [2808967.543203] EXT4-fs (sda3): re-mounted. Opts: (null) [2837776.220605] xv[14450] general protection ip:7f20c20c6ac6 sp:7fff3641b368 error:0 in libpng14.so.14.4.0[7f20c20a9000+29000] [4931344.685302] EXT4-fs (md16): re-mounted. Opts: (null) [4982666.631444] VFS: file-max limit 1231582 reached [4982666.764240] VFS: file-max limit 1231582 reached [4982767.360574] VFS: file-max limit 1231582 reached [4982901.904628] VFS: file-max limit 1231582 reached [4982964.930556] VFS: file-max limit 1231582 reached [4982966.352170] VFS: file-max limit 1231582 reached [4982966.649195] top[31095]: segfault at 14 ip 00007fd6ace42700 sp 00007fff20746530 error 6 in libproc-3.2.8.so[7fd6ace3b000+e000] Obviously, the file-max errors look suspicious, being clustered together and recent. # cat /proc/sys/fs/file-max 1231582 # cat /proc/sys/fs/file-nr 1231712 0 1231582 That also looks a bit odd to me, but the thing is, there's no way I have 1.2 million files open on this system. I'm the only one using it, and it's not visible to anyone outside the local network. # lsof | wc 16046 148253 1882901 # ps -ef | wc 574 6104 44260 I saw some documentation saying: file-max & file-nr: The kernel allocates file handles dynamically, but as yet it doesn't free them again. The value in file-max denotes the maximum number of file- handles that the Linux kernel will allocate. When you get lots of error messages about running out of file handles, you might want to increase this limit. Historically, the three values in file-nr denoted the number of allocated file handles, the number of allocated but unused file handles, and the maximum number of file handles. Linux 2.6 always reports 0 as the number of free file handles -- this is not an error, it just means that the number of allocated file handles exactly matches the number of used file handles. Attempts to allocate more file descriptors than file-max are reported with printk, look for "VFS: file-max limit reached". My first reading of this is that the kernel basically has a built-in file descriptor leak, but I find that very hard to believe. It would imply that any system in active use needs to be rebooted every so often to free up the file descriptors. As I said, I can't believe this would be true, since it's normal to me to have Linux systems stay up for months (even years) at a time. On the other hand, I also can't believe that my nearly-idle system is holding over a million files open. Does anyone have any ideas, either for fixes or further diagnosis? I could, of course, just reboot the system, but I don't want this to be a recurring problem every few weeks. As a stopgap measure, I've quit Firefox, which was accounting for almost 2000 lines of lsof output (!) even though I only had one window open, and now I can run 'ls' again, but I doubt that will fix the problem for long. (edit: Oops, spoke too soon. By the time I finished typing out this question, the symptom was/is back) Thanks in advance for any help. And another update: My system was basically unusable, so I decided I had no option but to reboot. But before I did, I carefully quit one process at a time, checking /proc/sys/fs/file-nr after each termination. I found that, predictably, the number of open files gradually went down as I closed things down. Unfortunately, it wasn't a large effect. Yes, I was able to clear up 5000-10000 open files, but there were still over 1.2 million left. I shut down just about everything. All interactive shells, except for the one ssh I left open to finish closing down, httpd, even nfs service. Basically everything in the process table that wasn't a kernel process, and there were still an appalling number of files apparently left open. After the reboot, I found that /proc/sys/fs/file-nr showed about 2000 files open, which is much more reasonable. Starting up 2 Xvnc sessions as usual, along with the dozen or so monitoring windows I like to keep open, brought the total up to about 4000 files. I can see nothing wrong with that, of course, but I've obviously failed to identify the root cause. I'm still looking for ideas, since I definitely expect it to happen again. And another update, the next day: I watched the system carefully, and discovered that /proc/sys/fs/file-nr showed a growth of about 900 open files per hour. I shut down the system's only NFS client for the night, and the growth stopped. Mind you, it didn't free up the resources, but it did at least stop consuming more. Is this a known bug with NFS? I'll be bringing the NFS client back online today, and I'll narrow it down further. If anyone is familiar with this behavior, feel free to jump in with "Yeah, NFS4 has this problem, go back to NFS3" or something like that.

    Read the article

  • How do I know if I have KMS enabled?

    - by Attila Oláh
    How can I check if KMS is enabled in my kernel? I've compiled mine with KMS radeon modeset defaulting to 1, but I still suspect that it is not enabled. EDIT: aatiis@aiur ~ $ dmesg | grep drm [drm] Initialized drm 1.1.0 20060810 [drm] Initialized radeon 1.33.0 20080528 for 0000:01:05.0 on minor 0 [drm] Setting GART location based on new memory map [drm] Loading RS780 CP Microcode [drm] Resetting GPU [drm] writeback test succeeded in 1 usecs EDIT 2: aatiis@aiur ~ $ glxinfo | grep render IRQ's not enabled, falling back to busy waits: 2 0 direct rendering: Yes OpenGL renderer string: Mesa DRI R600 (RS780 9612) 20090101 TCL aatiis@aiur ~ $ sudo grep -i kms /var/log/Xorg.0.log [ 57.201] (II) [KMS] drm report modesetting isn't supported.

    Read the article

  • How to disable "N" Wireless Mode RTL8192 (Thinkpad Edge 15 Core i5) in natty

    - by Gustavo Rubio
    I've seen many owners of thinkpad edges which are supossed to be linux-friendly having problems with wireless adapter. I've found several links inside askubuntu and in ubuntuforums which have a lot of work-arounds for those problems, mine seems to be wierd though. I use my laptop on both my office and at home. At home I have a router which is A/B/G and here at home the wireless connection works just fine, using a WEP key. But in work I have a B/G/N wireless router and it doesn't work, my guess is that this adapter works with N modes but somehow this is buggy in the bundled driver in natty. I've tried to disable the "N" mode in the router but that didn't work. Later I went to realtek website, downloaded their driver and compiled myself, kinda seems to work most of the time but sometimes some websites keep trying to load or load just parts of it and images start to look like their links are broken and so on, much like what you get when you were loading a page and suddenly the connection is lost. This problem, as I said, is only using the realtek driver from their website. Dmesg gives me this a lot of these: [ 5869.049454] rtl8192se_update_ratr_table: ratr_index=0 ratr_table=0x00000ff5 [ 5879.240563] DHCP pkt src port:68, dest port:67!! So I thougth I might as well switch back to the original driver which seems to work just fine on A/B/G wireless networks but not on N networks so if anybody knows how to disable that mode from within the driver please let us know :) Thanks in advance! PS: I do found a link to a similar question and it was answered but let me remind you I'm NOT using the intel version of wireless for my thinkpad but the realtek (RTL8192SvB)

    Read the article

  • How do I stop my ethernet network connection from dropping?

    - by Sean Hill
    My ethernet-based network connection doesn't stay up consistently. I'm running a ping against the gateway and it will: Work for a minute Freeze, time out, or give multi-second response times Repeat If it's stuck and I disable/enable networking through the network manager applet everything will work fine again for a minute. After 280 packets transmitted I'm getting 41% packet loss. I've tried a different cable and connection to the gateway but this had no effect. The distance to the gateway is just about 3 feet. Seems to work fine if I switch over to Windows, but Ubuntu is my main OS and I can't even use it right now as I depend on the network. My setup... OS: Ubuntu 11.04, dual-booting Windows 7 Mobo: Gigabyte Z68X-UD4-B3 CPU: Intel Core i7 2600K Edit A little clarification... Network Manager is still showing me as connected, but I am unable to reach to gateway or anything beyond. At no point does NM suggest the connection is lost and calling ifconfig shows that I still have an IP address. I tried connecting to a different gateway with a different cable and the same problem arises. As requested: lspci | grep -i eth 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) dmesg | tail -f [ 14.024709] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro,commit=0 [ 14.026443] EXT4-fs (sda7): re-mounted. Opts: commit=0 [ 14.176101] hda-intel: IRQ timing workaround is activated for card #2. Suggest a bigger bdl_pos_adj. [ 23.917731] eth0: no IPv6 routers present [ 726.109697] r8169 0000:07:00.0: eth0: link up [ 733.169494] r8169 0000:07:00.0: eth0: link up [ 753.930119] r8169 0000:07:00.0: eth0: link up [ 880.787332] r8169 0000:07:00.0: eth0: link up [ 1159.161283] r8169 0000:07:00.0: eth0: link up [ 1406.623550] r8169 0000:07:00.0: eth0: link up Edit @roland-taylor: Network is always available under Windows. Pings do not timeout, applications do not complain of no network availability, large downloads are not interrupted or slowed.

    Read the article

  • apache2 slow responding (debian)

    - by baloo
    I'm running an apache2 2.2.9 webserver with modpython and mpm_worker_module. The current config for the mpm is ServerLimit 32 StartServers 10 MaxClients 800 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 0 The server has 1G of ram and a 100Mbit connection. Checking netstat -na | grep ESTABLISHED | wc -l gives me a number between 50 - 60. The load is about 1.0 Every pageload is also cached by memcached. I can't see why the server is so slow in responding to new connections, sometimes droping them completely? Also tried disabling iptables to make sure it's not because of a full state table or something like that. The only thing in dmesg is a lot of spam about "TCP: Treason uncloaked!"

    Read the article

  • 10.10 boots to command line login prompt

    - by greggory.hz
    I recently installed Ubuntu 10.10 on a computer that was previously running 10.04 (that worked fine). Now, each time I boot up, it starts up in a command line login prompt. I can login and it stays at the command line (as expected). I can then manually start gdm with sudo start gdm and it works fine. I can also enable compiz (using proprietary nvidia drivers) so I'm reasonably confident that it's not a driver problem (at least not in the sense that the drivers just flat out aren't working). Interestingly, if I leave it at the command prompt without logging in, after about 5 or 10 minutes, gnome starts up on its own. I'm not sure what is causing this. This is what dmesg | tail gives me after a manual start of gdm: [ 15.664166] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 270.18 Tue Jan 18 21:46:26 PST 2011 [ 15.991304] type=1400 audit(1297543976.953:11): apparmor="STATUS" operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" pid=990 comm="apparmor_parser" [ 16.606986] eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1 [ 18.798506] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0 [ 26.740010] eth0: no IPv6 routers present [ 90.444593] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro,commit=0 [ 189.252208] audit_printk_skb: 21 callbacks suppressed [ 189.252213] type=1400 audit(1297544150.218:19): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1876 comm="apparmor_parser" [ 189.252584] type=1400 audit(1297544150.218:20): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1876 comm="apparmor_parser" [ 351.159585] lo: Disabled Privacy Extensions

    Read the article

  • 12.04 Wi-Fi not working correctly with Intel Pro/Wireless 3945ABG

    - by Jerel
    This is a very strange problem. The only time the Wi-Fi works is when I have the wired connection connected. I have a Dell 6400/e1505 with the Broadcom BCM 4401-B0 internal NIC, and the Intel Pro/Wireless 3945ABG Wi-Fi adapter. I was on 10.0.4 LTS before, and I remember having to screw around to get the Wi-Fi to work, but that was years ago, and now it's acting even stranger than it did back then. If I boot up with the wire connected, the Wi-Fi starts up. If I boot up without the wire connected, the Wi-Fi won't start at all. If after booting with the wire connected, and the Wi-Fi starts up, I then disable the wireless, the wired connection works fine. Without the wire connected, dmesg shows the iwl3945 driver loading and starting with no errors, and the wireless adapter activated. Running rfkill list shows no blocks, but there is no connection to my Wi-Fi. Help! I am more confused than a chameleon in a bag of Skittles.

    Read the article

  • How to find the /dev name of my USB device

    - by mustafa
    I am running Ubuntu 11 on VmWare on Windows XP. I want to format an SD card in Ubuntu. But, I can't figure out which /dev/xxx device the SD card is. I plug the card into the built-in socket of my laptop. I "safely remove" the device in Windows. Then, I "connect" the PCMCIA reader in VmWare. Now, I was supposing to see a new device like /dev/sdx. But, it doesn't appear :( How can I find what the name of my USB device's name and mount it? /var/log/message is empty. Here is the output of dmesg: [ 5268.927308] usb 2-1: new full speed USB device number 12 using uhci_hcd And, here is the last lines of /var/log/syslog: Oct 31 18:51:21 ubuntu kernel: [ 5268.927308] usb 2-1: new full speed USB device number 12 using uhci_hcd Oct 31 18:51:21 ubuntu mtp-probe: checking bus 2, device 12: "/sys/devices/pci0000:00/0000:00:11.0/0000:02:00.0/usb2/2-1" Oct 31 18:51:21 ubuntu mtp-probe: bus: 2, device: 12 was not an MTP device

    Read the article

  • Dell Laptop's Bluetooth isn't detected by Ubuntu

    - by vishwaje
    I have Dell vostro 3500 Laptop. I Installed Ubuntu 12.04. It doesn't detect my bluetooth. below is my information. lsusb | grep Bluetooth Bus 001 Device 003: ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth) lsmod | grep bluetooth bluetooth 158438 10 bnep,rfcomm rfkill list 0: brcmwl-0: Wireless LAN Soft blocked: yes Hard blocked: no 1: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: no (wifi working fine. I disabled it using network menu. So, it's fine) dmesg | grep Bluetooth [ 21.981835] Bluetooth: Core ver 2.16 [ 21.981872] Bluetooth: HCI device and connection manager initialized [ 21.981877] Bluetooth: HCI socket layer initialized [ 21.981881] Bluetooth: L2CAP socket layer initialized [ 21.981891] Bluetooth: SCO socket layer initialized [ 21.986047] Bluetooth: RFCOMM TTY layer initialized [ 21.986059] Bluetooth: RFCOMM socket layer initialized [ 21.986065] Bluetooth: RFCOMM ver 1.11 [ 22.361783] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 22.361791] Bluetooth: BNEP filters: protocol multicast So How can I fix this? I saw other place (I don't remember which site) They said, some times, when in windows, if bluetooth disabled by windows driver, It can't be enabled by linux. So, I should install windows and enable blueethooth from windows and then re install linux. That is impossible for me, because I don't have Windows installation media. But I tried this, which is I installed windows xp on virtual box. Vbox showed me thow unknow USB devices. I connected them and installed windows bluethooth drivers to xp. But it didn't ditected Bluethooth either. Also, when I set off mode in hardware switch, those unknown devices disappear from Vbox usb device seletcion menu. So, they are definitely something to do with wifi or bluethooth. Please help me..

    Read the article

  • iptables rule to submit packets matching a specific negative rule

    - by Aditya Sehgal
    I am using netfilter_queue to pick up certain packets from the kernel and do some processing on them. To, the netfilter queue, I need all packets from a particular source except UDP packets with src port 2152 & dst port 2152. I try to add the iptable rule as iptables -A OUTPUT ! s 192.168.0.3 ! -p udp ! --sport 2905 ! --dport 2905 -j NFQUEUE --queue-num 0 iptables throw up an error of Invalid Argument. Querying dmesg, I see the following error print ip_tables: udp match: only valid for protocol 17 I have tried the following variation with the same error thrown. iptables -A OUTPUT ! s 192.168.0.3 ! -p udp --sport 2905 --dport 2905 -j NFQUEUE --queue-num 0 Can you please advise on the correct usage of the iptables command for my case.

    Read the article

  • Will BIOS boot mode Ubuntu install be able to boot when firmware "Fast Boot" is "Ultra Fast"?

    - by Pro Backup
    I have an AsRock mainboard with UEFI BIOS P1.50 02/14/2014. The firmware "Fast Boot" option is set to "Fast", Boot Option #1 is set to "AHCI P4: OCZ-VERT...": this is BIOS not UEFI boot. This boot disk has an MBR partitioning scheme (# parted -l | grep Partition\ Table:). Therefore Ubuntu 14.04 is installed in BIOS/CMS (Grub-PC) mode. The Ubuntu boot process ends in a text console (no GUI). There is no external graphics card in use. The stock Ubuntu kernel is replaced with Ubuntu supplied mainline 3.16.0-031600rc6-generic. dmesg outputs lines containing BIOS, like: SMBIOS 2.7 present Calgary: detecting Calgary via BIOS EBDA area Calgary: Unable to locate Rio Grande table in EBDA - bailing! [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored BIOS EDD facility v0.16 2004-Jun-25, 0 devices found The ASRock BIOS it selves display this help text for "Ultra Fast - Fast Boot": Ultra Fast mode is only supported by Windows 8 and the VBIOS must support UEFI GOP if you are using an external graphics card. Please notice that Ultra Fast mode will boot so fast that the only way to enter this UEFI Setup Utility is to Clear CMOS or run the Restart to UEFI utility in Windows. Assumptions: I suspect after changing UEFI setting "Fast Boot" to "Ultra Fast" that the machine will no longer boot into Ubuntu's console. I expect when first exchanging "Grub-pc" with "Grub-efi", that the machine will still be able to boot to a grub menu (thus allowing to change the "Fast Boot" setting back to "Fast" without clearing CMOS). Are these two "Fast Boot" assumptions correct, and/or, may I expect Ubuntu 14.04 running mainline kernel 3.16rc6 and Grub-efi to still boot to console after enabling UEFI Ultra Fast Boot?

    Read the article

  • cpufreq not available 11.10

    - by code shogan
    on 11.04 I had cpufreq working on my "AMD Turion(tm) 64 X2 Mobile Technology TL-50 stepping 02" processors, however now on oneiric cpufreq won't load. The core temperature of my cpu is normally 40 c, but lately it's cooking away at 75-80+ c and the fan is always extremely loud even when cpu usage has at 0.4%. and after this dmesg | grep -i cpu I got: Brought up 2 CPUs Switch to broadcast mode on CPU1 Switch to broadcast mode on CPU0 Switched to NOHz mode on CPU #1 Switched to NOHz mode on CPU #0 ACPI: acpi_idle registered with cpuidle cpufreq-nforce2: No nForce2 chipset. cpuidle: using governor ladder cpuidle: using governor menu powernow-k8: Found 1 AMD Turion(tm) 64 X2 Mobile Technology TL-50 (2 cpu cores) (version 2.20.00) I see something about governors and ladder there, does this mean the OS is able to scale my cpu's or not? If so is there a way I can determine it's working? I saw that for other users that the wrong module had been loaded and by disabling it they were able to get cpufreq loaded. How can I tell what scaling module is loaded? stats: Ubuntu Oneiric 32bit Dell Inspiron 1501

    Read the article

  • Gentoo baselayout-2 problem with module parameters

    - by Alakdae
    I recently switched to baselayout-2 on my Gentoo machine but I have one problem. I autoload a module bttv with paramater: card=77,77 The problem is that at boot the module is loaded without the parameter which makes the video feed useless. I cannot find the cause because the funny thing is that when I put an echo in /etc/init.d/modules to see what is passed to modprobe, this is what I got: szymanowicz ~ # /etc/init.d/modules restart * WARNING: you are stopping a boot service * Caching service dependencies ... [ ok ] * Loading module bttv ... bttv card=77,77 [ ok ] * Autoloaded 1 module(s) It indicates that everything is OK, but dmesg shows that at boot time there are no parameters. bttv0: using: *** UNKNOWN/GENERIC *** [card=0,autodetected] ... bttv1: using: *** UNKNOWN/GENERIC *** [card=0,autodetected] Whereas when I run it manually I get: bttv0: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option] ... bttv1: using: GrandTec Multi Capture Card (Bt878) [card=77,insmod option] Please help me because reloading the modules every time there is a reboot is very anoying (not many reboots, but I need to remember about the module)

    Read the article

  • lirc_zilog IR transmission no longer working with HD-PVR on 12.04

    - by johnf
    I have been running a ubuntu 10.04 with a patched version of lirc_zilog for two years. I upgraded to 12.04 and lirc_zilog is no longer working with my HD-PVR. The MythTV wiki reports that it did work out of the box with 11.04. The error message I get on irsend is as follows: johnf@carbon:~$ /usr/local/bin/irsend SEND_ONCE blaster 0_130_KEY_POWER irsend: command failed: SEND_ONCE blaster 0_130_KEY_POWER irsend: hardware does not support sending The lircd daemon, run interactively, reports the following: lircd: accepted new client on /var/run/lirc/lircd lircd: could not get hardware features lircd: this device driver does not support the LIRC ioctl interface lircd: major number of /dev/lirc0 is 250 lircd: LIRC major number is 61 lircd: check if /dev/lirc0 is a LIRC device lircd: WARNING: Failed to initialize hardware lircd: error processing command: SEND_ONCE blaster 0_130_KEY_POWER lircd: hardware does not support sending lircd: removed client Checking dmesg seems to indicate that the kernel module is loading properly: [56497.730743] lirc_zilog: module is from the staging directory, the quality is unknown, you have been warned. [56497.730999] lirc_zilog: Zilog/Hauppauge IR driver initializing [56497.732484] lirc_zilog: ir_probe: ir_rx_z8f0811_hdpvr on i2c-0 (Hauppage HD PVR I2C), client addr=0x71 [56497.732493] lirc_zilog: ir_probe: ir_tx_z8f0811_hdpvr on i2c-0 (Hauppage HD PVR I2C), client addr=0x70 [56497.732496] lirc_zilog: probing IR Tx on Hauppage HD PVR I2C (i2c-0) [56497.756822] lirc_zilog: firmware of size 302355 loaded [56497.756945] lirc_zilog: 743 IR blaster codesets loaded [56497.757030] i2c i2c-0: lirc_dev: driver lirc_zilog registered at minor = 0 [56497.757033] lirc_zilog: IR unit on Hauppage HD PVR I2C (i2c-0) registered as lirc0 and ready [56497.757035] lirc_zilog: probe of IR Tx on Hauppage HD PVR I2C (i2c-0) done [56497.757056] lirc_zilog: initialization complete Here is my /etc/lirc/hardware.conf #Chosen IR Transmitter TRANSMITTER="HD-PVR" TRANSMITTER_MODULES="lirc_dev lirc_zilog" TRANSMITTER_DRIVER="" TRANSMITTER_DEVICE="/dev/lirc0" TRANSMITTER_SOCKET="" TRANSMITTER_LIRCD_CONF="" TRANSMITTER_LIRCD_ARGS="" My lircd.conf is a copy of the recommended one. Examination of the kernel source seems to indicate that the lirc_zilog module should support transmission, it's newer than the patched version I was manually compiling on 10.04. I was previously using a manually built version of lirc 0.8.7 and not the packaged one. I'm now running the packaged version 9.0. I can provide any additional information required and will perform tests quickly. I'm very eager to get this issue resolved.

    Read the article

  • How to install Wacom Bamboo Pen

    - by casadrya
    I have a new Wacom Bamboo Pen. I'm using Ubuntu 10.10 64bit. After googling a little bit, I checked that xserver-xorg-input-wacom was installed. I plugged in my tablet. I rebooted my computer. Nothing special happened. I opened Inkscape. The tablet didn't work. I opened Inkscape's Input devices dialog. I didn't understand anything. I tried to blindly click some options in that dialog but nothing seemed to have any effect. Same with Gimp. After googling some more I found the linuxwacom website with source code, this didn't seem to work. So... any help? As requested: lsusb Bus 005 Device 002: ID 056a:00d4 Wacom Co., Ltd dmesg | tail [ 492.961267] usb 5-1: new full speed USB device using uhci_hcd and address 3 [ 493.144862] input: Wacom Bamboo 4x5 Pen as /devices/pci0000:00/0000:00:1a.2/usb5/5-1/5-1:1.0/input/input6 [ 493.158854] input: Wacom Bamboo 4x5 Finger as /devices/pci0000:00/0000:00:1a.2/usb5/5-1/5-1:1.1/input/input7

    Read the article

  • Ubuntu server 9.10 freezes up after ~10 minutes

    - by Matt Williamson
    I just upgraded my Ubuntu server from 9.04 to 9.10 and after about 10 minutes it locks up. It won't respond to ping, can't ssh in and the terminal doesn't accept keyboard input. It does not have X installed. I then reformatted and installed it from scratch with the same results. There are two hard drives, the first is for the OS and the second is for media. The second has not changed, it is an ext3 formatted drive with one partition. I stopped random services (samba, ushare, transmission-daemon) to see if they were causing the issue, but it still locked up. I did a watch "dmesg|tail" until it locked up, but I didn't see anything. How can I troubleshoot this further? I don't want to downgrade. Machine specs: Dell Dimension 3000 Pentium 4 @3GHz 512M RAM

    Read the article

  • ubuntu box just redisplaying login screen after update

    - by David M. Karr
    My Ubuntu 12.04 box has been working fine. A recent update may have messed something up. I normally run remote windows on it, and I noticed that my windows were failing to start up. I then tried logging into it directly from the GUI console, and I'm seeing that after I press enter on the (valid) password, the page just redisplays. It's not a password error, as that would give me an inline error. I see some messages appear and disappear quickly between the login screen going away and then redisplaying, but they go away too quickly to read. I was able to run the non-gui login, and I did an update and upgrade, and then rebooted, but it's doing the same thing. I have a Samba connection from my Windows box, and that's still working. If it matters, here's my uname output (somewhat elided): Linux ... 3.2.0-26-generic #41-Ubuntu SMP Thu Jun 14 17:49:24 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux What can I do to troubleshoot this? Note that when I select "Guest Session", it lets me log in and displays the window manager. This seems significant to me. Does this mean that something specific to my login is causing it to fail? Note: If it matters, here's the output from /var/log/dmesg. The line about gdm seems interesting: [ 9.815883] Bluetooth: RFCOMM TTY layer initialized [ 9.815887] Bluetooth: RFCOMM socket layer initialized [ 9.815888] Bluetooth: RFCOMM ver 1.11 [ 9.879088] [PCSPP,TRISTATE] [ 9.879092] parport0: irq 7 detected [ 9.883935] type=1400 audit(1341871177.871:10): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=845 comm="apparmor_parser" [ 9.884365] type=1400 audit(1341871177.871:11): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/ntpd" pid=851 comm="apparmor_parser" [ 9.950397] e1000e 0000:00:19.0: irq 42 for MSI/MSI-X [ 9.961160] init: gdm main process (907) killed by TERM signal [ 9.966358] lp0: using parport0 (polling).

    Read the article

  • Ubuntu openGL issues

    - by Dank101
    my OpenGL doesn't work at all i get Xlib: extension "GLX" missing on display ":0". lspci output 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0126] (rev 09) (prog-if 00 [VGA controller]) 01:00.0 VGA compatible controller [0300]: NVIDIA Corporation Device [10de:1246] (rev a1) (prog-if 00 [VGA controller]) dmesg | grep -i nvid [ 9.469068] nvidia: module license 'NVIDIA' taints kernel. [ 9.538786] nvidia 0000:01:00.0: power state changed by ACPI to D0 [ 9.538792] nvidia 0000:01:00.0: power state changed by ACPI to D0 [ 9.538796] nvidia 0000:01:00.0: enabling device (0006 -> 0007) [ 9.538803] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9.538809] nvidia 0000:01:00.0: setting latency timer to 64 [ 9.538942] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 304.48 Sun Sep 9 [10300.955799] nvidia 0000:01:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10b) [10300.955803] nvidia 0000:01:00.0: restoring config space at offset 0xc (was 0x0, writing 0xfff80000) [10300.955807] nvidia 0000:01:00.0: restoring config space at offset 0x9 (was 0x1, writing 0x4001) [10300.955811] nvidia 0000:01:00.0: restoring config space at offset 0x7 (was 0xc, writing 0xd000000c) [10300.955814] nvidia 0000:01:00.0: restoring config space at offset 0x5 (was 0xc, writing 0xc000000c) [10300.955817] nvidia 0000:01:00.0: restoring config space at offset 0x4 (was 0x0, writing 0xf0000000) [10300.955820] nvidia 0000:01:00.0: restoring config space at offset 0x3 (was 0x800000, writing 0x10) [10300.955823] nvidia 0000:01:00.0: restoring config space at offset 0x1 (was 0x100006, writing 0x100007) my computer is a dell XPS l702x

    Read the article

  • why my server has a dir named "?"

    - by liuxingruo
    These are all the dirs in my server: ? bin boot dev etc home lib lost+found media media2 misc mnt net opt proc root sbin selinux srv sys tmp usr var why there is a "?" dir? Thanks very much. BTW: the touch command was found on my server(wiered). I list the bin dir: alsacard cp dd env hostname loadkeys more ps sed tcptraceroute alsaunmute cpio df ex igawk loadkeys.static mount pwd setfont traceroute6 arch csh dmesg false ipcalc logger mountpoint raw setserial tracert awk cut dnsdomainname fgrep kbd_mode login mv red sh view basename date doexec gawk keyctl ls netstat redhat_lsb_init sleep ypdomainname bash dbus-cleanup-sockets domainname gettext kill mail nice rm sort cat dbus-daemon dumpkeys grep ksh mailx nisdomainname rmdir stty chgrp dbus-monitor echo gtar ksh93 mkdir pgawk rpm su chmod dbus-send ed gunzip link mknod ping rvi sync chown dbus-uuidgen egrep gzip ln mktemp ping6 rview tar touch is missing, how can i get it back?

    Read the article

  • Managing Kindle Fire with on 12.04 via Micro-USB

    - by pirtle
    To begin, I have read both Is there a way to get a Kindle Fire to work with 12.04? and How can I transfer files to a Kindle Fire with a Micro-USB cable? My problem is that I am unable to mount my Kindle Fire in order to add books to it. I have installed calibre, but it is unable to manage any devices until the computer itself has recognized it. The latter post had an excellent answer (provided by @jeremiah) that was making some progress. Unfortunately, I think I don't know enough about the -t flag used with mount. This is what I've done... Ran dmesg to locate the device: [ 3.920886] sd 6:0:0:0: [sdb] Attached SCSI removable disk Confirmed it's location: $ sudo ls -l /dev/disk/by-id lrwxrwxrwx 1 root root 9 Aug 18 15:52 usb-Amazon_Kindle_3C6C002600000001-0:0 -> ../../sdb So we know that my Kindle is recognized on /dev/sdb. I then used the mount command suggested by @jeremiah: $ sudo mount -t ext3 /dev/sdb/ /mnt/kindle/ mount: no medium found on /dev/sdb The same error occurs for sudo mount /dev/sdb /mnt/kindle. Note: I have created the 'kindle' directory in 'mnt' Any suggestions?

    Read the article

  • Problems with wired ethernet connection Ubuntu 11.10

    - by Andrew Fielden
    After some partition shuffling, I've got a problem on my 11.10 system. The wired ethernet interface fails to come up, although the wireless interface is working. I'm using NetworkManager. I thought this may be a problem with NetworkManager, so I checked the config files, which look ok. I then tried re-installing the package, but this didn't resolve the issues. I'm not sure at this point if the problem is due to software configuration, or a hardware problem. I've also tried the cable in other router ports, but same problem. The symptoms are:- System settings - Network reports that the cable is unplugged (it isn't) ifconfig reports the following eth0 Link encap:Ethernet HWaddr f0:4d:a2:a2:a7:fe UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:792 (792.0 B) TX bytes:0 (0.0 B) Interrupt:46 Base address:0xe000 My /etc/network/interfaces file has the following: auto lo iface lo inet loopback My /etc/resolv.conf file has the following: # Generated by NetworkManager The router's red light is on for this port dmesg reports ADDRCONF(NETDEV_UP): eth0: link is not ready

    Read the article

  • Is a disk/ata timeout exception dangerous?

    - by j-g-faustus
    I have a few hard drives in mdadm RAID 5 configured to go to standby after a few minutes of inactivity. (Using hdparm.conf spindown_time.) At irregular intervals I get messages like these in dmesg: [ 1840.251661] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 1840.251722] ata4.00: failed command: SMART [ 1840.251758] ata4.00: cmd b0/d5:01:06:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in [ 1840.251759] res 40/00:14:50:2e:04/00:00:02:00:00/40 Emask 0x4 (timeout) [ 1840.251858] ata4.00: status: { DRDY } [ 1840.251888] ata4: hard resetting link [ 1840.600742] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 1840.601521] ata4.00: configured for UDMA/133 [ 1840.601547] ata4: EH complete [337877.713988] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [337877.714019] ata4.00: failed command: SMART [337877.714038] ata4.00: cmd b0/d5:01:06:4f:c2/00:00:00:00:00/00 tag 0 pio 512 in [337877.714039] res 40/00:04:90:10:81/00:00:00:00:00/40 Emask 0x4 (timeout) [337877.714089] ata4.00: status: { DRDY } [337877.714107] ata4: hard resetting link [337878.063085] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [337878.063743] ata4.00: configured for UDMA/133 [337878.063764] ata4: EH complete I think the exception is caused by smartd when a drive does not wake up quickly enough. There are no issues (that I can tell) in accessing the drives normally through the file system - it takes a few seconds longer than normal when they are asleep, but there are no exceptions. Is this something I should worry about, as a potential symptom on something that could corrupt a drive over time? Or can I safely ignore it as part of normal operation? Edit: By request: smartctl -a for sdaand sde, both disks are members of the array. If ata4is the same as scsi-4 then sde is the one that gave the error above, according to /dev/disk/by-path.

    Read the article

< Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >