Search Results

Search found 5389 results on 216 pages for 'bridge router'.

Page 111/216 | < Previous Page | 107 108 109 110 111 112 113 114 115 116 117 118  | Next Page >

  • Setting up a Time Capsule with port forwarding

    - by Kaji
    Our old AirPort Extreme station hit EOL, so we decided to upgrade it to a Time Capsule. Along the way, we're trying to also set it up with a separate guest network and port forwarding/NAT, however we're having trouble setting it up so that the time capsule is handling the DHCP leases instead of the router. We've got DSL through Verizon through a Westell modem/router to the Time Capsule. Done the RTFM thing, and we haven't been able to get it to work. Can anyone explain how to get things set up properly for this configuration?

    Read the article

  • Setting up a Time Capsule with port forwarding

    - by Kaji
    Our old AirPort Extreme station hit EOL, so we decided to upgrade it to a Time Capsule. Along the way, we're trying to also set it up with a separate guest network and port forwarding/NAT, however we're having trouble setting it up so that the time capsule is handling the DHCP leases instead of the router. We've got DSL through Verizon through a Westell modem/router to the Time Capsule. Done the RTFM thing, and we haven't been able to get it to work. Can anyone explain how to get things set up properly for this configuration?

    Read the article

  • Could not open IPV6 addr on web browser

    - by vito
    I have ipv6 address fe80::21f:a4ff:fe91:2e44%4. This is the address of modem/router. I am unable to open this address in browser to view the web configuration. I am able to telnet to fe80::21f:a4ff:fe91:2e44%4, view the console UI & can do settings. I can also open 192.168.1.1(IPv4 address of modem/router) in browser. I tried [fe80::21f:a4ff:fe91:2e44] in all browsers like IE, Firefox & Chrome. It was not possible.

    Read the article

  • Get the wireless adapter frequency-band mode in Windows 7

    - by Petr
    I have a dual-band 802.11n router operating in both frequency bands with the same SSID. My Windows 7 laptop has a dual-band wireless adapter. Is there a way to find out which frequency band is the one currently used by the client? Also, is there a way to set the preffered band? Thanks. EDIT1: The router is Linksys E4200 (V2) and I essentially want to keep the 2.4GHz band in the mixed-mode so that the legacy 802.11g devices can connect while allocating the 5.0GHz band for 802.11n devices. The laptop's adapter (Intel Centrino Ultimate-N 6300 ANG) can operate in both 802.11n modes. EDIT2: Related topic

    Read the article

  • Cannot connect to WEBrick on home network

    - by Chris Stewart
    I'm an Android developer and often my applications require server-side code. I typically use Ruby on Rails for the web app, and during development will run the server on my local machine (Mac OS X) with WEBrick. In the morning when I get to the office, I'll run ifconfig in the console to see what IP my laptop has been given that day. I'll use that IP in my Android app when making requests to the web app in question. This all works fine, when I'm in my office. When I get home, I attempt to do the same thing, find my laptop's IP via ifconfig, set it in my app's config file, but the destination can never be found. To exclude my app from the set of hurdles, I attempt to visit the web server IP (e.g., http://192.168.1.4:3000) from my phone's browser, and it cannot connect. If I try from my laptop, which is running the web server, it works fine. If I try from another machine, on the same network, it also is unable to connect. Given this, I think I've narrowed it down to some kind of configuration in my home network, but I frankly have no idea what the cause could be. I don't have anything special at home, your basic Verizon FiOS router/modem with everything connected via Wi-Fi (Wi-Fi for both phone and laptop at work as well, fyi). I've tried disabling the firewall on my Verizon router, enabling port forwarding, and just about everything else I could do for port 3000, and nothing has changed. Dear Server Fault geniuses, please help a poor developer out. :) Edit: Some follow up items to add. My Mac's firewall is not active, and all incoming requests are allowed. I've also verified on my phone and laptop, that they're on the same network (192.168.1.4 Mac, 192.168.1.9 Phone). I have no idea why this isn't working. Edit 2: I went into System Preferences, enabled Web Sharing, and tried to view the website from my phone and it didn't connect. So it's not WEBrick or related to Rails. The firewall on my machine is off and the firewall on my router is off. Edit 3: Some progress. I set up port forwarding for port 3000 to my laptop, found the external IP, and used that and it connected fine. So, there's definitely something not quite set up correctly on my internal network.

    Read the article

  • How can I port forward with an airport extreme and a NAT enabled modem?

    - by Jon
    I run an Actiontec HD701D modem with NAT to an Airport extreme base station to laptop etc. As you might expect I get double NAT issues. I tried a lot of different things to forward a port, but no luck. Currently the airport is in bridge mode letting the modem handle the NAT, but still can't forward the port. Also to note: firewall is off on the router, firewall is set to allow the application in OSX 10.6.3 and I did forward the port in the router. No luck.

    Read the article

  • Why is my ipad's wireless so flakey?

    - by Mark
    I'm the proud owner of a new IPad here in the UK. All is good, except for the wifi, which is a bit flakey. It connects fine to my Draytek router which is set for WPA/WPA2 and 56g only, displaying full signal strength. Then, after a few minutes, it goes down to minimum strength... And sometimes it goes back up again. A few times, it seems to loose connection completely, and needs to be turned off and on again. I've looked at the Apple support site, and have tried their recommendations (which are not really very relevant), but still nothing. I've tried setting the router to wpa2 only, and setting long-preamble. Right now, I guess I want to know if it's a hardware problem with my device and should be returned, or if it's a problem with all ipads which will be resolved. Guess I could take it back to the Mac genius bar, but I find those guys so incredibly pretentious and, frankly, rather useless, that i'd rather wait until I've exercised other options!

    Read the article

  • Vista laptop won't connect to airport extreme

    - by Hutch
    Our previous router died, and to replace it I procured an apple airport extreme. My mac, my wrt54gs (with ddwrt acting as a bridge) and a linux machine have had no problem connecting to the wireless. None of the wired clients are having a problem obviously. The problem is one of my roommates can not connect. That's not strictly true. He can connect to the network, and will, infact, get a dhcp lease. However he cannot get any packets out. Can't ping the router, can't access any web sites, nothing. However he's fine if we switch to an unsecured network. Which is obviously not acceptable. The airport only allows for 'wpa/wpa2 personal' and 'wpa2 personal' (and of course the enterprise versions there of) I keep reading about this problem in multiple spots on the web, but never see any actual answers... Anyway the laptop: hp/compaq cq50-215nr vista home premium wireess card: atheros 5007 airport is simultaneos dualband II

    Read the article

  • SSH access from outside to a pc inside network

    - by Raja
    I have a static IP and ADSL router linked to a linksys wireless router to which all my machines are connected. I would want to setup SVN on one of machines and provide SSH access which should be accessible by users outside my network. Would this be possible? Even just SVN access through web should be fine. Please let me know what all things should be done to achieve this ? I have Ubuntu VM running in a iMac Leopard machine and another 2 Win 7 32/64 bit machines. I can setup standalone Ubuntu or Win XP on another machine. Thanks, Raja.

    Read the article

  • wireshark not seeing all packets on WiFi

    - by Caffeine Coma
    I'm using Wireshark on OSX, trying to sniff my home network over WiFi. While I can see packets that are sent to/from the host I'm sniffing on, I'm not seeing anything else that goes over the WiFi. It's like I'm not in promiscuous mode or something (the promiscuous mode box is in fact checked). The router is an Apple Airport Extreme, protected by WPA2. I'm attached to the network I'm trying to sniff, so I'm confused about why I can't see other traffic. Edit: I solved this by the following: Plug Macbook directly into the Airport Extreme router Enable "internet sharing" on Macbook, with no password. Bind wireless device (the one I wanted to sniff) to the WiFi hotspot generated by Internet sharing in step 2. Run Wireshark on the Macbook, bound to device en1. Don't forget to disable sharing after you're done. :-)

    Read the article

  • Server 2008, 2 NICs, 2 fixed IPs - big delays using internet

    - by user46055
    Hi geniuses I have an all in one Windows 2008 server, configured with AD/DHCP/DNS/RRAS - all set up with wizards and no specific tweaking. The server has 2 network adapters : one of which ("MyWAN") is plugged into our office's internet connection, the other ("MyLAN") is plugged into a local switch, which is also where all our desktops are connected. So this one server is doing everything. When first set up, MyLAN had a fixed IP of 192.168.2.1 and served the desktops with DHCP scope 192.168.2.50-99. It also told them to use 192.168.2.1 as DNS and gateway. MyWAN was setup to take its IP etc from DHCP, being handled by the building's router and ADSL modem etc. All desktops were setup to use DHCP. This all worked perfectly fine, until I recently changed MyWAN to have a static IP (I wanted to access it from home, and needed to give it a static IP to port map in the building's router). Things still work, but there is now a long delay when accessing the internet. The actual speed is as before when downloading, but there is a pause of 3-6 secs when connecting to new hosts (for example if I browse to slashdot from either a desktop or the server itself, it'll hang on connecting to slashdot.org, hang again on connecting to *.fsdn, *.google-analytics.com and all the other hosts referenced from the main page). If I ping slashdot.org from the server, I get the following : Pinging slashdot.org [216.34.181.45] with 32 bytes of data: Reply from 192.168.2.1: Destination host unreachable. Reply from 216.34.181.45: bytes=32 time=99ms TTL=239 Reply from 216.34.181.45: bytes=32 time=100ms TTL=239 Reply from 216.34.181.45: bytes=32 time=101ms TTL=239 Pinging anywhere external always seems to hit 192.168.2.1 first, which doesn't seem right. Trying tracert from the server gives the following : Tracing route to slashdot.org [216.34.181.45] over a maximum of 30 hops: 1 MYSERVER01.intranet [192.168.2.1] reports: Destination host unreachable Trying tracert from a desktop gives the following : Tracing route to slashdot.org [216.34.181.45] over a maximum of 30 hops: 1 <1 ms * <1 ms MYSERVER [192.168.2.1] 2 * * * Request timed out. 3 6 ms 6 ms 6 ms dsl-gw1.ge.mer.uk.webtapestry.net [217.151.111.17] 4 38 ms 239 ms 251 ms gw-router.ge.mer.uk.webtapestry.net [217.151.111.13] ...and then all is fine after that. I think that DNS is working fine because the domain names are getting translated to correct IPs immediately. DHCP seems to be okay? So perhaps it's something up with my RRAS setup - although I can't see any option during the setup wizard which I would have filled in differently. I've also tried changing the binding order of the two network connections, to prioritise MyWAN, but that doesn't seem to have done anything. Any idea what's up? Many thanks - Rob

    Read the article

  • MBPro, mid 2010 can't see Dlink DIR655 signal after sleep etc

    - by user88114
    This is my son's MBP 7,1 running Snow Leopard 10.6.7. Router signal is fine since iPad, Wintel on same table 20 feet from router are fine. the MBP however frequently wakes and fails to find the internet. iStumbler can see 1 neighbours hub and my garden hub are there but can't get to the normal DIR655 wifi... no ping no en0 or en1 device seems to exist. Airport off and on does not help. He just resets router and it all works but this does not please me! I must admit the winter sometimes seems to loose connect too, but less so. The DIR655 (hardware rev A3) is on the original EU firmware 1.10, I'm cautious about jumping to latest 1.31EU since no downgrade seems to be possible and that feels a bit risky as so much is set up and working fine. If I use the DIR655 admin web and release the lease the MBP has then wake it all worked OK. So I suspect lease timing/locking issue but unsure how to check up, plus why iStumbler seems to say the network is not visible at all when I sit on the iPad right next to it just fine.. I do not think there are any channel overlaps and we also have RFquiet DECT phones (Orchid) that are silent until lifted or called. Anyway signals all show low interference and high throughput except for this failure to connect. Just walked the MBP to the garden office and iStumbler now sees the more distant DIR655 signal although it will not connect to it (does not show under Sys Prefs NetNetwork names) even after airport off & on... It also refuses to connect to my garden network (an old Belkin acting as AP wired to DIR655), the signal it can see and even net name in Sys Prefs NetNetwork names (2 mins later):NOW both names ARE visible, but both fail to accept the correct WPA2 password and keep asking again after failing to connect. IT ALL MAKES NO SENSE TO ME. Just revoked the lease for the MBP on DIR655 and no changes although this seemed to help MBP wake into connection 1 hour ago. OK a bit of walking about to report. Carried MBP across garden towards DIR655, a few other wifis show up on iStumbler, low signals all channel 1. Right next to DIR655 but iStumbler not showing it, although most other wifi's have gone. I'd say iStubler is suffering timeouts&hangs but hard to be sure. Lots of attempts to Airport on/off, join other etc and suddenly I get to connect, get given new IP (I revoked), can browse. Walk away, connection drops quite soon at 30 feet then reconnected briefly then died again. MUST ATTEND ELSEWHERE FOR A BIT...

    Read the article

  • Why ping another innet machine from MacBook get netgate's ip address?

    - by Xinwang
    I have three machine in my home network connected by a wireless router. One is server installed linux at 192.168.1.1, another is Thinkpad with MS Windows XP at 192.168.1.2, last one is MacBook Pro with Mac OS X 10.6.3 at 192.168.1.3. When I ping the Linux Server from Thinkpad (MS Windows XP) I can get the correct ip address, but when I ping it from Mac I get the global address of my router, like 61.135.181.175. Could you tell me why this happen? And how do I get same ping result on Mac and Windows. Thanks

    Read the article

  • dd-wrt switch for PfSense

    - by Kmao
    I currently have eth2 on my pfsense set up, and configured as 192.168.1.1, it has dhcp setup with allocation being 192.168.1.10 - 192.168.1.245. On my dd-wrt box, i disabled the WAN, and set it to act as a port for the switch. I disabled dhcp, dnsmasq, spi firewall, Wlan0 and set a static IP for the router being 192.168.1.10 Pfsense is plugged into lan0 and pc plugged into lan1 (wan port is empty) I have followed a few different guides, but i can't seem to get my router to act as a switch. Anyone have success using DD-WRT as a switch while using pfsense as your dhcp/dns/gateway. Any advice would help :)

    Read the article

  • Configure ubuntu 12.10 to share internet through second NIC with subnetwork

    - by Dan Smith
    I have an Ubuntu 12.10 box with 2 NICs. eth0 is connected to my 192.168.1.X network, which is connected to my home router and out to the internet. I want the other interface, eth1,to support 10.0.0.x and allow devices on that network to access the internet through my ubuntu box. I do not need dhcp on the 10.0.0.x network. Here's a schematic: Internet --- home router ---- ubuntu[eth0:192.168.1.x, eth1:10.0.0.x] --- [10.0.0.x device] How do I configure the ubuntu box to share the internet with devices on that subnetwork? Thanks!

    Read the article

  • setup advanced filtering and access restrictions on dd-wrt using iptables

    - by Nova deViator
    I have a linksys WRT54GL router with a DD-WRT installed and I want to setup some advanced filtering that seem to not be available through "Access restrictions" web gui option. I guess I would be using IPTABLES then. I have ssh access to router and can run iptables, but I'm not so experienced with iptables. So here are my needs: my policy would be deny all first and then allow exceptions allow all http (port 80) access to WAN through wireless allow all other traffic only to PCs with specific MAC addresses allow internet access to PC with specific MAC address according to schedule (let's say everyday between 18:00-21:00) is this possible to setup with IPtables? could somebody help me a bit with it? or should go and RTFM?

    Read the article

  • diagnostic software for wifi adapter

    - by Nathan Fellman
    I'm having trouble with my wifi connection. Is there any software out there that can help me determine if the problem is in the drivers or in the hardware? Regretfully, I'm working on Vista Edit: The problem I'm having is that the Vista reports that the wireless radio is connected, shows an IP and all, the router also shows that the computer is connected, but there's no connectivity. I can't logon to the router, and I can't even ping it. When I ping it I get the response: General Failure I have tried connecting with and without various wireless security protocols. I have tried disabling the wireless adapter and re-enabling it from the Device Manager I have tried updating the driver None of this has helped. When I connect via Ethernet (with a cable, that is), everything works fine. Edit: I'm not using any firewall on the computer, that I'm aware of. The IP address for the WIFI adapter is similar to the one for the LAN adapter. They differ by one.

    Read the article

  • FTP error when doing file transfer

    - by Ernie
    I'm running vsftpd version 3.0.2 over FTPeS, and I'm having a bit of trouble with file transfers. It seems to work fine when I'm on the LAN, but not from an external IP address. I have the control port and data ports open on my server's software firewall and my router's firewall. When I'm using the service from an external IP address, it seems like sometimes a file transfer will complete, but it times out and I always get the client error: "426 Failure writing network stream". I've tried several clients. I'm thinking there is some sort of data sabotage either at the router or some server policy; maybe because I'm using passive ftp? Suggestions?

    Read the article

  • Configure Wireless Network Card

    - by Skizz
    I recently upgraded the wireless network card in my Ubuntu PC from an 802.11g to an 802.11n. Now, it can't see my router. It doesn't appear in the list of networks that is displayed when you click on the NetworkManager icon in Gnome. Other networks are listed and I have connected to them (no password required!). I'm using the Windows driver through ndiswrapper and it can see the card. I tested the card in a Windows PC and everything worked. The router's log doesn't show any messages coming from the wireless card. What have I done wrong? If you need any more information, just leave a comment and I'll get add it to the question.

    Read the article

  • Configuring Nagios BGP plugin on Ubuntu

    - by user141610
    I am trying to configure nagios check_bgp_neighbors plug-in on Ubuntu and followed README file of check_bgp_neighbors plug-in. I have made following changes: define command{ command_name check_bgp_all command_line $USER1$/check_bgp_neighbors -H $HOSTADDRESS$ -C $USER3$ -n $ARG1$ -n $ARG2$ } to define command{ command_name check_bgp_all command_line /usr/local/nagios/libexec/check_bgp_neighbors.sh -H xx.xx.xx.49 -C xx.xx.xx.50 And define service{ use server-service hostgroup_name svc-bgp1 service_description BGP Check 1 check_command check_bgp_all!10.0.0.1!172.16.0.2 } to define service{ use generic-service hostgroup_name svc-bgp1 service_description BGP Check 1 check_command check_bgp_all!xx.xx.xx.50 } xx.xx.xx.49 is the IP of the host router and xx.xx.xx.50 is the IP of eBGP neighbour. After that it shows critical status. I know my command is not correct but cannot detect the problem. I learned that in this plug-in user-name and password of the host router are required but don't know how and where to provide it. Nagios log does not show any error message. Status information: Failed: status:0 prefixes:0 sent:0 received:0

    Read the article

  • Network trials and tribulations

    - by MauiWowie
    Hi, I am in the process of setting up a small (two PC's, both running Windows 7) network using a D-link DI-604 router (which acts only as hub, it's not set up in any way). In the Network and 'Sharing Center' in 'Control Panel' I clicked 'Set up a New (Connection or) Network'. All went well up until the moment I attempted to connect one PC with the other (in the 'Connect' dialog I entered the other PC's IP, no pwd). I can use both PC's to connect to and browse the net though, so the router/hub does not seem to be the problem. And I must have done something right, because the other computer shows up in the 'Network Map'. Any and all help is much appreciated!

    Read the article

  • Netgear VPN can't access specific server

    - by Critologist
    I have a Netgear FVS318N configured with a VPN. I'm trying to access my call recorder with the provided software from another office. I've already setup the VPN connection, and it works. I can connect and ping the remote router and a few other things on the network. However, I can't ping or connect to my call recorder. If I move outside of the office network (i.e. connect directly to the cable modem or via a mobile hotspot), I can connect and ping the call recorder just fine. The office has a simple Linksys WRT54G router and is using AT&T Uverse. The remote location is using Charter Cable with a Netgear FVS318N. Has anyone ever encountered anything like this before? I've setup an identical VPN previously for a different client using similar hardware and never encountered this. Thanks in advance!

    Read the article

  • How to route all traffic over site to site VPN tunnel?

    - by Hutch
    I have a site to site VPN configured between our main site (Site A) and a remote site (Site B). Site A is 10.60.0.0/16 Site B is 192.168.99.0/24 The firewall in Site B is a Juniper SSG running ScreenOS 6.3 and I'm using a route based VPN. The tunnel works perfectly in that from Site A you can reach 192.168.99.0 via the tunnel, and from Site B you can reach 10.60.0.0 via the tunnel. However, we want it so that if you're in Site B and want the Internet it goes via the firewall at Site A, and right now on the Juniper 0.0.0.0 has the ISP router as next hop. My understanding is that on the Juniper, I can set a route for the /32 public IP at our main site that the VPN tunnel connects to to the ISP router via ethernet0/0 (the SSG's external interface), and then modify the 0.0.0.0 route to use our main site firewall via tunnel.1 (the VPN tunnel). Not sure I've explained that so well but is my understanding correct? Thanks

    Read the article

  • How to query a DHCP server to get the local DNS servers

    - by Dan Berlyoung
    I have a ClarkConnect (CentOS based) box running as my home router on a RR connection. I had the DNS servers set up to use Google's DNS server. I want to change them back to the local DNS servers but I can't find an obvious/easy way to get those address short of a) reconfiguring the router's network to DHCP them (would rather not interrupt everyone) or b) calling their tech support (kill me now!). Is there a command line tool/command I can use to query the DHCP server on the external NIC to see what DNS servers it would set me up with w/o munging my existing setup?

    Read the article

  • Windows 7 PPTP VPN problem

    - by Marco Martins
    Hi, I'm currently using an win 7 as an network server at my home. I've created some shared folders wich can be accessed easily from any pc on my network (win and mac computers) recently I decided to turn on the win 7 pptp to access remotely to my server from anywhere. the problem is with that on, on my router my server ip change, acording to my ipconfig on the cmd my router gets the ip from a "PPP adapter RAS (dial in)". when that happens I cannot access to the shared files over the lan on my mac, but i can connect to the vpn but again can't access to my files. (i've tried connecting to the vpn from another network and it worked, even the file share) anyone can help me? thanks

    Read the article

< Previous Page | 107 108 109 110 111 112 113 114 115 116 117 118  | Next Page >