Search Results

Search found 4245 results on 170 pages for 'rookie 22'.

Page 111/170 | < Previous Page | 107 108 109 110 111 112 113 114 115 116 117 118  | Next Page >

• Connect to Apache times out randomly

  - by Amadan

  We are trying to set up an Apache server on a remote machine, but we experience strange behaviour. Checking with telnet remote.machine 80, one of these things happen randomly: Connect and serve content normally (no delay) Connect after a long pause Connect normally, then time out without response Timeout on connect Once connected, the request seems to be processed normally. These things do not occur if I connect from that machine directly to localhost 80. The Apache is dedicated, as is the server it runs on (runs only this one application, no-one else is using it for anything else). I am not an administrator of the remote site, and I do not know the network architecture over there, but apparently it's firewalled: (HTTP port is open, SSH port is IP-restricted, most others are closed). If there was any one pattern, I might have some ideas, but this variety of symptoms baffles me. Any ideas as to what could be causing this? Apache is 2.2; Server version is: Linux version 2.6.9-22.ELsmp ([email protected]) (gcc version 3.4.4 20050721 (Red Hat 3.4.4-2)) #1 SMP Mon Sep 19 18:32:14 EDT 2005

  Read the article

• Windows 7 ssh file server.

  - by Siriss

  Hello all- I have looked at the other posts, but have not quite found an answer I have a question about windows file sharing over SSH. I have copssh installed and it is working for Remote desktop connections. I have port 22 forwarded on my router etc. I connect from a Mac or Putty with this address: ssh -l copsshusername 3391:localhost:3389 [external ip] That works fine. I would like to configure Windows 7 to allow my ssh account that I use to login, access to certain shared folders. I have documents and videos and things that I would like to be able to download externally. I have done this before on Linux and a long time ago on XP, but I cannot figure out what I am missing on Windows 7. There is a designated SSH user that copssh uses to run the service and that I use to to login as. I have googled and googled and have not found a solution that does everything I need that is why I am turning here for ideas. I hope I am explaining this correctly. Thank you very much for your help!

  Read the article

• OS X can connect to Windows machine, but can't access shared folders

  - by Bonnie

  I can create new folders on my Windows XP machine, set them to "shared". On my Mac, I pick Finder → Go → Connect to Server → smb://192.168.1.4 → Connect → Name / Password. It even shows me all the names of the newly created shared-folders on my PC, but when I try to actually connect to any of them I get connection failed, there was an error connecting Any idea on what would cause that? The fact that it successfully gets so far—to actually showing me my PC share-names—must mean I have 99% of this working correctly, i.e. the physical connection, the IP address, the user name, the password, etc. Still, I can't seem to access the folders themselves. I've tried this with my Windows XP firewall on/off, and Norton AntiVirus on/off. Same problem. Everything did work fine, 4 months ago. Were there any odd OS X or Windows updates released recently? I always apply them all. smbclient on the Mac does correctly find the XP machine, my XP user name, and accepts my XP password. I get the following from that smbclient command: Doing spnego session setup (blob length=16) server didn't supply a full spnego negprot Got challenge flags: ... Got NTLMSSP flags: ... Got NTLMSP flags: ... Domain=[XPMACHINE] OS=[Windows 5.1] Server=[Windows 2000 LAN Manager] tree connect failed: NT_STATUS_INSUFF_SERVER_RESOURCES I'm not sure why a standard XP box can't "supply a full spnego negprot". Whatever that means. Using XP's RegEdit to change my IRPStackSize from 11... to 13, 15, 20, 22... still gives that "NT_STATUS_INSUFF_SERVER_RESOURCES" error on the Mac.

  Read the article

• Varnish returning 503, FetchError (could not get storage)

  - by Archan

  On the current setup we're running into a problem with Varnish, we're running a CentOS 5.7 x86_64 xenpv, with Cpanel WHM, hosted at VPS.net. Sometimes we will recieve a Guru Meditation from Varnish, and when we look in the varnishlog with the following command varnishlog -d -c -m TxStatus:503 it returns output similar to the following: 15 VCL_call c recv 15 VCL_acl c NO_MATCH devs 15 VCL_return c pass 15 VCL_call c hash 15 Hash c **** 15 Hash c ************* 15 VCL_return c hash 15 VCL_call c pass pass 15 Backend c 12 default default 15 TTL c 1835862523 RFC 0 -1 -1 1332454056 0 1332454055 375007920 0 15 VCL_call c fetch hit_for_pass 15 ObjProtocol c HTTP/1.1 15 ObjResponse c OK 15 ObjHeader c Date: Thu, 22 Mar 2012 22:07:35 GMT 15 ObjHeader c Server: Apache/2.2.21 (Unix) mod_ssl/2.2.21 OpenSSL/0.9.8e-fips-rhel5 mod_bwlimited/1.4 mod_fcgid/2.3.6 15 ObjHeader c X-Powered-By: PHP/5.3.9 15 ObjHeader c Expires: Thu, 19 Nov 1981 08:52:00 GMT 15 ObjHeader c Cache-Control: no-store, no-cache, must-revalidate, post-check=0, pre-check=0 15 ObjHeader c Pragma: no-cache 15 ObjHeader c Content-Type: text/html; charset=utf-8 15 ObjHeader c X-Cacheable: NO:Cache-Control=private 15 FetchError c chunked read_error: 12 (Could not get storage) 15 VCL_call c error deliver 15 VCL_call c deliver deliver As far as I have could gather, we could try increasing the nuke_limit, but currently we have a nuke_limit of 500, and when running varnishstat -1 -f n_lru_nuked we "only" get a total of 1031, even though we have seen the error happen on several pages. When we then run top to see how much memory Varnish is using, it only shows that it is using 763m, although we've set it to be allowed to use 1200m. Any ideas of what the problem can be?

  Read the article

• hosts.deny ignored by MacOSX 10.8

  - by David Holm

  I have been trying to set up my MacOS X Server, which I recently upgraded to Mountain Lion, to use denyhosts as I need to open port 22 to it. denyhosts is set up and adds entries to /etc/hosts.deny so I decided to add my laptops IP to it in order to verify that it actually works but I can still log in and my IP shows up in /private/var/log/system.log. I even rebooted the server once just to be sure there wasn't some service that had to be restarted. I tried the following entries: ALL: <my laptop's IP> sshd: <my laptop's IP> sshd: 127.0.0.1 My /etc/sshd_config has the following parameters set: UsePAM yes UseDNS no I Googled if deny.hosts has been deprecated in OSX 10.7 or 10.8 but I couldn't find any indications that it has. Any ideas of what is going wrong or if there is an alternative way to achieve the same result? Yes, a private key would solve this problem but for the time being I would like to stick to using password authentication. I also like the idea of denyhosts actually blocking access to all services running on the server and not just ssh.

  Read the article

• Apache Mod SVN Access Forbidden

  - by Cerin

  How do you resolve the error svn: access to '/repos/!svn/vcc/default' forbidden? I recently upgraded a Fedora 13 server to 16, and now I'm trying to debug an access error with a Subversion server running on using Apache with mod_dav_svn. Running: svn ls http://myserver/repos/myproject/trunk Lists the correct files. But when I go to commit, I get the error: svn: access to '/repos/!svn/vcc/default' forbidden My Apache virtualhost for svn is: <VirtualHost *:80> ServerName svn.mydomain.com ServerAlias svn DocumentRoot "/var/www/html" <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory "/var/www/html"> Options Indexes FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> <Location /repos> Order allow,deny Allow from all DAV svn SVNPath /var/svn/repos SVNAutoversioning On # Authenticate with Kerberos AuthType Kerberos AuthName "Subversion Repository" KrbAuthRealms mydomain.com Krb5KeyTab /etc/httpd/conf/krb5.HTTP.keytab # Get people from LDAP AuthLDAPUrl ldap://ldap.mydomain.com/ou=people,dc=mydomain,dc=corp?uid # For any operations other than these, require an authenticated user. <LimitExcept GET PROPFIND OPTIONS REPORT> Require valid-user </LimitExcept> </Location> </VirtualHost> What's causing this error? EDIT: In my /var/log/httpd/error_log I'm seeing a lot of these: [Fri Jun 22 13:22:51 2012] [error] [client 10.157.10.144] ModSecurity: Warning. Operator LT matched 20 at TX:inbound_anomaly_score. [file "/etc/httpd/modsecurity.d/base_rules/modsecurity_crs_60_correlation.conf"] [line "31"] [msg "Inbound Anomaly Score (Total Inbound Score: 15, SQLi=, XSS=): Method is not allowed by policy"] [hostname "svn.mydomain.com"] [uri "/repos/!svn/act/0510a2b7-9bbe-4f8c-b928-406f6ac38ff2"] [unique_id "T@Sp638DCAEBBCyGfioAAABK"] I'm not entirely sure how to read this, but I'm interpreting "Method is not allowed by policy" as meaning that there's some security Apache module that might be blocking access. How do I change this?

  Read the article

• Postgresql connection refused

  - by Jonathan

  I'm trying to remotely connect to my postgresql database. I have two virtual machines set up both running ubuntu 14.04. I am trying to connect to the second vm using the first vm using psql -h 10.0.1.23 -U postgres -d postgres But I receive the error: Could not connect to server: Connection refused Is the server running on host "10.0.1.23" and accepting TCP/IP connections on port 5432? I have changed the pg_hba.conf and added host all all 10.0.1.64/24 md5 host all all * md5 host all all 0.0.0.0/0 md5 And changed the postgresql.conf listen_address=" * " In an attempt to allow all incoming connections. I have also tried to change the firewall settings, but I am unsure of whether or not the ports are properly listening for the connection. Edit: Output of netstat -an | grep -E '^tcp[^6].*LISTEN' tcp 0 0 127.0.1.1:53 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:23 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:5432 0.0.0.0:* LISTEN

  Read the article

• I want to use OpenVPN to access the web and email from China. How?

  - by gaoshan88

  My question: How do I use my already existing OpenVPN setup to enable secure, remote web surfing and email checking from open wireless hotspots? Some long winded details: I am running Ubuntu and have OpenVPN up and working fine as a server. My client machine connects fine as well. However, that just gets me a secure connection to my home network. What I want is to be able to access my VPN server and surf the web or check email securely from anywhere with an open wireless connection. I am frequently in China and having secure, unblocked access would be a boon (especially since I like to work from tea houses and coffee shops and I've already had a password sniffed and hacked once). I already know how to tunnel over SSH via a SOCKS proxy using something like: ssh -ND 8887 -p 22 [email protected] but since I have OpenVPN I figure why not try it? So... what are the steps involved in making it so I can connect to my VPN and the surf and check mail to my hearts content (slowly to be sure but at least it wold be secure). Thx!

  Read the article

• Should I partition my main table with 2 millions rows?

  - by domribaut

  Hi, I am a developer and would need some DBA-advices. We are starting to get performance problem with a MSSQL2005 database. The visible effects of the incidents is mainly CPU-hog on the server but operations reported that it was also draining resources from the SAN (not always). the main source of issues is for sure in some application but I am wondering if we should partition some of the main tables anyway in order to relax the I/O pressure. The base is about 60GB in one file. The main table (order) has 2.1 Million rows with a 215 colones (but none is huge). We have an integer as PK so it should be OK to define a partition function. Will we win something with partitioning? will partition indexes buy us something? Here are some more facts about the DB and the table database_name database_size unallocated space My_base 57173.06 MB 79.74 MB reserved data index_size unused 29 444 808 KB 26 577 320 KB 2 845 232 KB 22 256 KB name rows reserved data index_size unused Order 2 097 626 4 403 832 KB 2 756 064 KB 1 646 080 KB 1688 KB Thanks for any advice Dom

  Read the article

• In Icinga (Nagios), how do I configure hosts with multiple IPs?

  - by gertvdijk

  I'm setting up Icinga (Nagios fork) and I have some machines with multiple interfaces. Some services are only listening on one of them and to check them correctly, I like to know if it's possible to have multiple IP addresses configured for a single host in Icinga. Here's a minimal example: Remote Server: eth0: 1.2.3.4 (public IP) eth1: 10.1.2.3 (private IP, secure tunnel) Apache listening on 1.2.3.4:80. (public only) OpenSSH listening on 10.1.2.3:22. (internal network only) Postfix SMTP listening on 0.0.0.0:25 (all interfaces) Icinga Server: eth0: 10.2.3.4 (private IP, internet access) Now if I define a host: define host { use generic-host host_name server1 alias server1.gertvandijk.net address 10.1.2.3 } This will not check the HTTP status correctly. And defining an additional host: define host { use generic-host host_name server1-public alias server1.gertvandijk.net address 1.2.3.4 } will check everything, but shows up as two independent hosts. Now I want to 'aggregate' these two hosts to show up as a single host, yet providing an easy configuration to check the services on their proper address. What is the most elegant number-of-configuration-lines-saving solution to this? I read about several plugins available to workaround this, but I can't figure out what is the current way to address it. Solutions go back to 2003, but I'm running Icinga 1.7.1, already capable of the address6 option, yet that triggers IPv6-only resolving on the hostname... Ideally, I wish to configure Icinga to be intelligent enough to know that the Postfix instance running on 10.1.2.3:25 is the same as 1.2.3.4:25 and thus not triggering two alarms. I guess this must have been tackled before and sysadmins have it set up now. Please share your solution to this. Thanks! :)

  Read the article

• git : The remote end hung up unexpectedly - too many simultaneous users?

  - by Pritam Barhate

  I asked this first on StackOverflow and I was suggested that I should ask it here: We have a self hosted git server (Gitolite) on a VPS account (CPU:2.68GHz RAM:1824MB). This same VPS is also used to publish our underdevelopment web apps for client demos. (Very little traffic). so the main use of the server is as a Git Server Only. This git server is accessed by a team of 30-40 people for various projects. Our problem is that during the day when 6-7 people are trying to access the server (sometimes same repo) we get frequent error message: ssh: connect to host xxx.xxx.xx.xx port 22: Bad file number fatal: The remote end hung up unexpectedly After trying for 10-15 minutes it generally succeeds. During early mornings and late nights when there are only 1-2 people, git commands work with 100% success rate. Also I would like to note that if I access the other file hosted on the server through HTTP it works fine. I found a couple of questions on StackOverflow and on other sites regarding this. But most of the people point towards SSH key set up or conflicts between Msysgit and Cygns SSH. However I don't think this is the problem in our case as we get this behavior on Windows (using msysgit only) as well as Mac Machines. Also if it was SSH configuration issue then it shouldn't work at all. But in our case it works after 10-15 minutes. I think in our case it might be too many simultaneous connections to same server (or same repo) or something like that. Does there exists a setting or a conf file that needs to modified to solve this problem? Please help me solve this problem or point me in the right direction. Thanks in advance. Pritam.

  Read the article

• iptables -- OK, **now** am I doing it right?

  - by Agvorth

  This is a follow up to a previous question where I asked whether my iptables config is correct. CentOS 5.3 system. Intended result: block everything except ping, ssh, Apache, and SSL. Based on xenoterracide's advice and the other responses to the question (thanks guys), I created this script: # Establish a clean slate iptables -P INPUT ACCEPT iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT iptables -F # Flush all rules iptables -X # Delete all chains # Disable routing. Drop packets if they reach the end of the chain. iptables -P FORWARD DROP # Drop all packets with a bad state iptables -A INPUT -m state --state INVALID -j DROP # Accept any packets that have something to do with ones we've sent on outbound iptables -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT # Accept any packets coming or going on localhost (this can be very important) iptables -A INPUT -i lo -j ACCEPT # Accept ICMP iptables -A INPUT -p icmp -j ACCEPT # Allow ssh iptables -A INPUT -p tcp --dport 22 -j ACCEPT # Allow httpd iptables -A INPUT -p tcp --dport 80 -j ACCEPT # Allow SSL iptables -A INPUT -p tcp --dport 443 -j ACCEPT # Block all other traffic iptables -A INPUT -j DROP Now when I list the rules I get... # iptables -L -v Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 0 0 DROP all -- any any anywhere anywhere state INVALID 9 612 ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- lo any anywhere anywhere 0 0 ACCEPT icmp -- any any anywhere anywhere 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:ssh 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:http 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:https 0 0 DROP all -- any any anywhere anywhere Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 5 packets, 644 bytes) pkts bytes target prot opt in out source destination I ran it and I can still log in, so that's good. Anyone notice anything major out of wack?

  Read the article

• Apache can't get viewed from outside of my LAN

  - by Javier Martinez

  I fixed it in PORTS TRIGGER menu of my router. Thanks you anyway I have a weird problem related with (i think) my cable-router and my configured vhosts in Apache2. The point is I can't access from outside of my LAN to any of my configured vhosts if I set the http port of Apache to 80 and i add a NAT rule for it. Otherwise, if I set my Apache port to 81 (or any else) with its respective NAT rule on my router it works. My router is an ARRIS TG952S and I am using Apache/2.2.22 (Debian) ports.conf NameVirtualHost *:80 Listen 80 vhost1.mydomain.net.conf <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName vhost1.mydomain.net ServerAlias vhost1.mydomain.net www.vhost1.mydomain.net vhost2.mydomain.net.conf <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName vhost2.mydomain.net ServerAlias vhost2.mydomain.net www.vhost2.mydomain.net DNS records (using FreeDNS) are: mydomain.net --> pointing to another server vhost1.mydomain.net --> pointing to my server vhost2.mydomain.net --> pointing to my server iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination fail2ban-apache-noscript tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 80,443 fail2ban-apache tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 80,443 fail2ban-ssh tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 22 Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain fail2ban-apache (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-apache-noscript (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-ssh (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Thanks you

  Read the article

• Iptables rules, forward between two interfaces

  - by Marco

  i have a some difficulties in configuring my ubuntu server firewall ... my situation is this: eth0 - internet eth1 - lan1 eth2 - lan2 I want that clients from lan1 can't communicate with clients from lan2, except for some specific services. E.g. i want that clients in lan1 can ssh into client in lan2, but only that. Any other comunication is forbidden. So, i add this rules to iptables: #Block all traffic between lan, but permit traffic to internet iptables -I FORWARD -i eth1 -o ! eth0 -j DROP iptables -I FORWARD -i eth2 -o ! eth0 -j DROP # Accept ssh traffic from lan1 to client 192.168.20.2 in lan2 iptables -A FORWARD -i eth1 -o eth2 -p tcp --dport 22 -d 192.168.20.2 -j ACCEPT This didn't works. Doing iptables -L FORWARD -v i see: Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 33 144 DROP all -- eth1 !eth0 anywhere anywhere 0 0 DROP all -- eth2 !eth0 anywhere anywhere 23630 20M ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- eth1 any anywhere anywhere 175 9957 ACCEPT all -- eth1 any anywhere anywhere 107 6420 ACCEPT all -- eth2 any anywhere anywhere 0 0 ACCEPT all -- pptp+ any anywhere anywhere 0 0 ACCEPT all -- tun+ any anywhere anywhere 0 0 ACCEPT tcp -- eth1 eth2 anywhere server2.lan tcp dpt:ssh All packets are dropped, and the count of packets for the last rule is 0 ... How i have to modify my configuration? Thank you. Regards Marco

  Read the article

• Openbsd init script for ssh VPN tunnel

  - by manthis

  I have a server hosting SSH tunnels and Openbsd 4.5 clients connecting to it. Things work just fine but I am in the need of automating the connection from the client to the server. So that if the client is accidentally rebooted, then the connection initiates unattended. So it should be as straight forward as to include the ssh connection in an init script. However I have miserably failed to do so by including it to /etc/rc.local, which is the file I usually do this sort of things in. Right now I am using autossh to also restart the connection if necessary and the script that I put on /etc/rc.local follows: #!/bin/sh # # Example script to start up tunnel with autossh. # # This script will tunnel 2200 from the remote host # to 22 on the local host. On remote host do: # ssh -p 2200 localhost # # $Id: autossh.host,v 1.6 2004/01/24 05:53:09 harding Exp $ # ID=root HOST=example.com #AUTOSSH_POLL=600 #AUTOSSH_PORT=20000 #AUTOSSH_GATETIME=30 #AUTOSSH_LOGFILE=$HOST.log #AUTOSSH_DEBUG=yes #AUTOSSH_PATH=/usr/local/bin/ssh export AUTOSSH_POLL AUTOSSH_LOGFILE AUTOSSH_DEBUG AUTOSSH_PATH AUTOSSH_GATETIME AUTOSSH_PORT autossh -2 -f -M 20000 ${ID}@${HOST} The script detaches just fine when run manually so I just include it on /etc/rc.local as echo -n 'starting local daemons:' if [ -x /usr/local/sbin/autossh.sh ]; then echo -n 'ssh tunnel' /usr/local/sbin/autossh.sh fi echo '.' I have also tried calling it from /etc/hostname.tun0 in case there may be issues with /etc/rc.local not being called at the right time when network connections are ready, so I would use: inet 10.254.254.2 255.255.255.252 10.254.254.1 !/usr/local/sbin/autossh.sh Your input is highly appreciated.

  Read the article

• Trying to install datastax opscenter - Failed to load application: cannot import name _parse

  - by gansbrest

  I'm not familiar with python, maybe someone could explain what's going on here? ec2-user@prod-opscenter-01:~ % java -version java version "1.7.0_45" Java(TM) SE Runtime Environment (build 1.7.0_45-b18) Java HotSpot(TM) 64-Bit Server VM (build 24.45-b08, mixed mode) ec2-user@prod-opscenter-01:~ % python -V Python 2.6.8 ec2-user@prod-opscenter-01:~ % openssl version OpenSSL 1.0.1e-fips 11 Feb 2013 And now the error ec2-user@prod-opscenter-01:~ % sudo /etc/init.d/opscenterd start Starting Cassandra cluster manager opscenterd Starting opscenterdUnhandled Error Traceback (most recent call last): File "/usr/lib64/python2.6/site-packages/twisted/application/app.py", line 652, in run runApp(config) File "/usr/lib64/python2.6/site-packages/twisted/scripts/twistd.py", line 23, in runApp _SomeApplicationRunner(config).run() File "/usr/lib64/python2.6/site-packages/twisted/application/app.py", line 386, in run self.application = self.createOrGetApplication() File "/usr/lib64/python2.6/site-packages/twisted/application/app.py", line 451, in createOrGetApplication application = getApplication(self.config, passphrase) --- <exception caught here> --- File "/usr/lib64/python2.6/site-packages/twisted/application/app.py", line 462, in getApplication application = service.loadApplication(filename, style, passphrase) File "/usr/lib64/python2.6/site-packages/twisted/application/service.py", line 405, in loadApplication application = sob.loadValueFromFile(filename, 'application', passphrase) File "/usr/lib64/python2.6/site-packages/twisted/persisted/sob.py", line 210, in loadValueFromFile exec fileObj in d, d File "bin/start_opscenter.py", line 1, in <module> from opscenterd import opscenterd_tap File "/usr/lib/python2.6/site-packages/opscenterd/opscenterd_tap.py", line 37, in <module> File "/usr/lib/python2.6/site-packages/opscenterd/OpsCenterdService.py", line 13, in <module> File "/usr/lib/python2.6/site-packages/opscenterd/ClusterServices.py", line 22, in <module> File "/usr/lib/python2.6/site-packages/opscenterd/WebServer.py", line 40, in <module> File "/usr/lib/python2.6/site-packages/opscenterd/Agents.py", line 18, in <module> exceptions.ImportError: cannot import name _parse Failed to load application: cannot import name _parse Maybe there are open source alternatives to monitoring cassandra I should look at? Thanks a lot

  Read the article

• How do I log back into a Windows Server 2003 guest OS after Hyper-V integration services installs and breaks my domain logins?

  - by Warren P

  After installing Hyper-V integration services, I appear to have a problem with logging in to my Windows Server 2003 virtual machine. Incorrect passwords and logins give the usual error message, but a correct login/password gives me this message: Windows cannot connect to the domain, either because the domain controller is down or otherwise unavailable, or because your computer account was not found. Please try again later. If this message continues to appear, contact your system administrator for assistance. Nothing pleases me more than Microsoft telling me (the ersatz system administrator) to contact my system administrator for help, when I suspect that I'm hooped. The virtual machine has a valid network connection, and has decided to invalidate all my previous logins on this account, so I can't log in and remotely fix anything, and I can't remotely connect to it from outside either. This appears to be a catch 22. Unfortunately I don't know any non-domain local logins for this virtual machine, so I suspect I am basically hooped, or that I need ophcrack. is there any alternative to ophcrack? Second and related question; I used Disk2VHD to do the conversion, and I could log in fine several times, until after the Hyper-V integration services were installed, then suddenly this happens and I can't log in now - was there something I did wrong? I can't get networking working inside the VM BEFORE I install integration services, and at the very moment that integration services is being installed, I'm getting locked out like this. I probably should always know the local login of any machine I'm upgrading so I don't get stuck like this in the future.... great. Now I am reminded again of this.

  Read the article

• What's going on with traceroute?

  - by Kevin

  The following is what happens when I run traceroute from a certain location: # traceroute google.com traceroute to google.com (74.125.227.39), 30 hops max, 60 byte packets 1 gateway.local.enactpc.com (10.0.0.1) 0.138 ms 0.101 ms 0.084 ms 2 * * * 3 * * * 4 * * * 5 * * * 6 * * * 7 * * * 8 * * * 9 * * * 10 * * * 11 * * * 12 * * * 13 * * * 14 * * * 15 * * * 16 * * * 17 * * * 18 * * * 19 * * * 20 * * * 21 * * * 22 * * * 23 * * * 24 * * * 25 * * * 26 * * * 27 * * * 28 * * * 29 * * * 30 * * * Absolutely nothing of interest... Now, originally I thought this was just a fact of the location's network set up. (I assume they block pings or something...) However, watch what happens when I use nmap to run a traceroute... # nmap -sP --traceroute google.com Starting Nmap 5.21 ( http://nmap.org ) at 2012-09-25 22:18 CDT Nmap scan report for google.com (74.125.227.40) Host is up (0.034s latency). Hostname google.com resolves to 11 IPs. Only scanned 74.125.227.40 rDNS record for 74.125.227.40: dfw06s06-in-f8.1e100.net TRACEROUTE (using proto 1/icmp) HOP RTT ADDRESS 1 0.19 ms gateway.local.enactpc.com (10.0.0.1) 2 1.93 ms 99-20-92-1.lightspeed.austtx.sbcglobal.net (99.20.92.1) 3 25.61 ms 99-20-92-2.lightspeed.austtx.sbcglobal.net (99.20.92.2) 4 ... 6 7 23.68 ms 12.83.68.137 8 31.30 ms gar23.dlstx.ip.att.net (12.122.85.73) 9 ... 10 31.82 ms 72.14.233.65 11 32.27 ms 209.85.250.77 12 32.98 ms dfw06s06-in-f8.1e100.net (74.125.227.40) Nmap done: 1 IP address (1 host up) scanned in 3.29 seconds When using nmap I get A LOT more results than with traceroute, why? Note, I checked, and the difference in target IP addresses is not related...

  Read the article

• Fast extraction of a time range from syslog logfile?

  - by mike

  I've got a logfile in the standard syslog format. It looks like this, except with hundreds of lines per second: Jan 11 07:48:46 blahblahblah... Jan 11 07:49:00 blahblahblah... Jan 11 07:50:13 blahblahblah... Jan 11 07:51:22 blahblahblah... Jan 11 07:58:04 blahblahblah... It doesn't roll at exactly midnight, but it'll never have more than two days in it. I often have to extract a timeslice from this file. I'd like to write a general-purpose script for this, that I can call like: $ timegrep 22:30-02:00 /logs/something.log ...and have it pull out the lines from 22:30, onward across the midnight boundary, until 2am the next day. There are a few caveats: I don't want to have to bother typing the date(s) on the command line, just the times. The program should be smart enough to figure them out. The log date format doesn't include the year, so it should guess based on the current year, but nonetheless do the right thing around New Year's Day. I want it to be fast -- it should use the fact that the lines are in order to seek around in the file and use a binary search. Before I spend a bunch of time writing this, does it already exist?

  Read the article

• Problems forwarding port 3306 on iptables with CentOS

  - by BoDiE2003

  Im trying to add a forward to the mysql server at 200.58.126.52 to allow the access from 200.58.125.39, and Im using the following rules (its my whole iptables of the VPS of my hosting). I can connect locally at the server that holds the mysql service as localhost, but not from outside. Can someone check if the following rules are fine? Thank you # Firewall configuration written by system-config-securitylevel # Manual customization of this file is not recommended. *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :RH-Firewall-1-INPUT - [0:0] -A INPUT -j RH-Firewall-1-INPUT -A FORWARD -j RH-Firewall-1-INPUT -A RH-Firewall-1-INPUT -i lo -j ACCEPT -A RH-Firewall-1-INPUT -p icmp --icmp-type any -j ACCEPT -A RH-Firewall-1-INPUT -p 50 -j ACCEPT -A RH-Firewall-1-INPUT -p 51 -j ACCEPT -A RH-Firewall-1-INPUT -p udp --dport 5353 -d 224.0.0.251 -j ACCEPT -A RH-Firewall-1-INPUT -p udp -m udp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -p tcp -m tcp --dport 631 -j ACCEPT -A RH-Firewall-1-INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A RH-Firewall-1-INPUT -j REJECT --reject-with icmp-host-prohibited -A RH-Firewall-1-INPUT -m state --state NEW -m tcp -p tcp -s 200.58.125.39 --dport 3306 -j ACCEPT -A INPUT -p tcp -s 200.58.125.39 --sport 1024:65535 -d localhost --dport 3306 -m state --state NEW,ESTABLISHED -j ACCEPT -A OUTPUT -p tcp -s localhost --sport 3306 -d 200.58.125.39 --dport 1024:65535 -m state --state ESTABLISHED -j ACCEPT COMMIT And this is the output of the connection trial. [root@qwhosti /home/qwhosti/public_html/admin/config] # mysql -u user_db -p -h 200.58.126.52 Enter password: ERROR 2003 (HY000): Can't connect to MySQL server on '200.58.126.52' (113)

  Read the article

• postfix - connection refused from behind NAT

  - by manchine

  When attempting to telnet postfix from a different host in the same LAN through the FQDN (and thus the LAN's public IP), the following error occurs: root@mailer:/var/log# telnet mail.domain.com 25 Trying 1.2.3.4... telnet: Unable to connect to remote host: Connection refused Other services can be reached from the exact same host, however: root@mailer:/var/log# telnet mail.domain.com 22 Trying 1.2.3.4... Connected to mail.domain.com. Escape character is '^]'. SSH-2.0-OpenSSH_6.0p1 Debian-4+deb7u1 To make matters more intriguing, Postfix can be accessed from outside the LAN: nunos-mbp:mailog nzimas$ telnet mail.domain.com 25 Trying 1.2.3.4... Connected to mail.domain.com. Escape character is '^]'. 220 mail.domain.com ESMTP Postfix (Ubuntu) To sum thing up: a) Postfix (running on 10.10.10.4 / mail.domiain.com) refuses connection from a host in the same LAN (10.10.10.2), but only when queried through the FQDN (mail.domain.com) b) mail.domain.com accepts connections to other services (but Postfix) from 10.10.10.2 c) mail.domain.com accepts connections to all services, including Postfix, from the outside world If it were a firewall issue, then I believe it would not be possible to connect to any service from 10.10.10.2 through the FQSN / public IP. It ought to be some missing parameter in Postfix, although I haven't found any clear pointers so far.

  Read the article

• System occasionally hangs boot process with SLES 11

  - by ThaMe90

  I have several (new) systems on which I had to install SLES11 on. However, after a few (though not every) reboots, the system hangs during the boot sequence. It will only continue after I physically press a key on the keyboard. From what I've found in the dmesg log from a failed boot is the following: [ 22.170276] sd 0:0:0:0: [sda] Mode Sense: b7 00 00 08 [ 22.171155] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 22.182760] sda: sda1 sda2 sda3 [ 22.383424] sd 0:0:0:0: [sda] Attached SCSI disk [ 22.545372] PM: Marking nosave pages: 000000000009a000 - 0000000000100000 [ 22.545377] PM: Marking nosave pages: 00000000bf780000 - 0000000100000000 [ 22.546217] PM: Basic memory bitmaps created [ 22.590380] PM: Basic memory bitmaps freed [ 22.596284] PM: Starting manual resume from disk [ 22.602319] PM: Resume from partition 8:1 [ 22.602321] PM: Checking hibernation image. [ 22.602479] PM: Error -22 checking image file [ 22.602481] PM: Resume from disk failed. [ 22.718727] kjournald starting. Commit interval 15 seconds [ 22.718960] EXT3-fs (sda3): using internal journal [ 22.718964] EXT3-fs (sda3): mounted filesystem with ordered data mode [ 1555.644404] udevd version 128 started [ 1555.697664] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0 [ 1555.707961] ACPI: Power Button [PWRB] I've looked around the internet for the PM: Resume from disk failed. message, but this seems to only be important when restoring the system after a hybernate, i.e. restore from the hdd. But this is not my situation. I only get this after a reboot, as I said before. The timestamp [ 1555.xxxxxx] is only the result of me pressing a key on the keyboard. Any suggestions on how to proceed? As I am getting stuck on this issue.

  Read the article

• Almost All Xenserver Logical Volumes Disappeared - Recovery?

  - by Alex

  We had a hard disc crash of one of two hard discs in a software raid with a LVM on top. The server is running Citrix xenserver. On the hard disk which is still intact, the volume group gets detected well, but only one LV is left. (some hashes replaced by "x") # lvdisplay --- Logical volume --- LV Name /dev/VG_XenStorage-x-x-x-x-408b91acdcae/MGT VG Name VG_XenStorage-x-x-x-x-408b91acdcae LV UUID x-x-x-x-x-x-vQmZ6C LV Write Access read/write LV Status available # open 0 LV Size 4.00 MiB Current LE 1 Segments 1 Allocation inherit Read ahead sectors auto - currently set to 256 Block device 253:0 root@rescue ~ # vgdisplay --- Volume group --- VG Name VG_XenStorage-x-x-x-x-408b91acdcae System ID Format lvm2 Metadata Areas 1 Metadata Sequence No 4 VG Access read/write VG Status resizable MAX LV 0 Cur LV 1 Open LV 0 Max PV 0 Cur PV 1 Act PV 1 VG Size 698.62 GiB PE Size 4.00 MiB Total PE 178848 Alloc PE / Size 1 / 4.00 MiB Free PE / Size 178847 / 698.62 GiB VG UUID x-x-x-x-x-x-53w0kL I could understand if a full physical volume is lost - but why only the logical volumes? Is there any explanation for this? Is there any way to recover the logical volumes? EDIT We are here in a rescue system. The problem is that the whole server does not boot (GRUB error 22) What we are trying to do is to access the root filesystem. But everything was in the LVM. We have only this: (parted) print Model: ATA SAMSUNG HD753LJ (scsi) Disk /dev/sdb: 750GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 750GB 750GB primary boot, lvm And this 750GB LVM volume is exactly what we see on top. edit2 Output of vgcfgrestore, but from the rescue system, as there is no root to chroot to. # vgcfgrestore --list VG_XenStorage-x-b4b0-x-x-408b91acdcae File: /etc/lvm/archive/VG_XenStorage-x-x-x-x-408b91acdcae_00000.vg VG name: VG_XenStorage-x-x-x-x-408b91acdcae Description: Created *before* executing '/sbin/vgscan --ignorelockingfailure --mknodes' Backup Time: Fri Jun 28 23:53:20 2013 File: /etc/lvm/backup/VG_XenStorage-x-x-x-x-408b91acdcae VG name: VG_XenStorage-x-x-x-x-408b91acdcae Description: Created *after* executing '/sbin/vgscan --ignorelockingfailure --mknodes' Backup Time: Fri Jun 28 23:53:20 2013

  Read the article

• Backup files from Linux client to Windows Server

  - by Andrew

  I'm trying to backup my files from my Linux box to my Windows Server 2008 as a push, and when I delete them from my Linux box, they remain on my Windows Server. I've found lots of sources that are similar, but most results were from Windows to Linux. I managed to find slightly more similar cases like Using rsync and cygwin to Sync Files from a Linux Server to a Windows Notebook PC, and rsync from Windows PC to remote Linux server, with the most similar being a backup from Linux to Windows Server, but through a pull from the Windows Server. Initially, I used Unison because I thought having the 2-way capability would come in handy, and I would just have to set some configurations to make it 1-way. Unfortunately, I couldn't find the right configuration, and only managed to synchronize using the command unison "profile" -ui text -auto -silent. When I deleted the files on my Linux box, the files in the Server got deleted too, which of course, isn't what I want. When I tried to find any options for Unison, I only discovered the -force option, which didn't help, since what I wanted was an incremental update to the Server. I found out I could achieve this from using rsync and the -a option (archive), which would keep adding files even if I deleted them from my Linux box. I installed Cygwin on my Windows Server, configured an SSH daemon, but I can't seem to get it working. I've also already configured Windows Firewall to open port 22 (both inbound and outbound). I used the following command from my Linux box: rsync -avrzn /folder/to/be/backed/up/ [email protected]:/cygdrive/c/place/to/store/backed/up/files (a - archive, v - verbose, r - recurse into subdirectories, z - compress, n - dryrun) but it just won't work. Can anyone help me out? I don't mind using either Unison or rsync, as long as it achieves what I want.

  Read the article

• Delayed internet access

  - by Joel Coel

  When I (and presumably my users) first start up or log in to my computer I can't get internet access until several minutes after logging in. Internet pages like serverfault.com will time out. During this time I can access internal web servers. Sometimes pinging the gateway seems to fix the problem. I'm using Windows 7 on this machine with wifi, and the problem seems limited to the wifi network, which is on a separate vlan. The wired network does not share the problem, but I know it's not the wifi connection itself because the internal sites work. The wifi access point is attached to a 3Com 4200 switch, with the port set for vlan 2 untagged, vlan 1 tagged. The 4200 has a fiber connection to a 3Com 4900SX fiber switch that acts almost as a router here. The fiber connection is vlan 1 untagged vlan 2 tagged at both ends. The gateway is then attached to a different 4200 (vlan 1 untagged, vlan 2 tagged) that has a similar fiber connection to the 4900SX. vlan 2 has 192.168.8.0/22 IPs, vlan 1 has 10.1.0.0/16 IPs. The 4900SX has an interface for both vlans (10.1.1.1/192.168.8.1), as does the gateway (10.1.1.5/192.168.8.5). There is one dchp server for both vlans on the same switch as the gateway. It chooses a dhcp scope based on the interface used by the 4900sx to forward the dhcp request. There is also a network access list on the 4900sx set to deny all vlan2 traffic to any 10.1.x.x host, with exceptions made for a few servers, including dhcp, 4900sx, and the gateway. I think that about covers it. Any ideas on why internet access would be delayed like this?

  Read the article

< Previous Page | 107 108 109 110 111 112 113 114 115 116 117 118  | Next Page >