Search Results

Search found 9688 results on 388 pages for 'external hdd'.

Page 114/388 | < Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >

  • Getting the local IP address in Ubuntu 10.04 LTS

    - by Andreas Grech
    I am trying to get my locally assigned IP address from Ubuntu 10.04 LTS with ifconfig and what I'm getting is my external IP address (in other words, it's the same IP I see on whatismyip.com) When running ifconfig eth0, inet addr shows my external IP address instead of the local address. How do I get my local IP address ?

    Read the article

  • How to create NTFS partition in Linux to install Windows 7 from USB?

    - by Michal Stefanow
    I messed up with my computer and need help. Generally: install Windows 7 from USB. Problem: "setup was unable to create a new system partition" When first attempt to install Windows 7 failed I tried Linux live USB, installed distro to HDD, and erased all the existing partitions. Current state (fdisk -l): [writing from other computer so no copy and paste] /dev/sda1 305GB Linux /dev/sda2 7GB Extended /dev/sda5 7GB Linux Swam / Solaris To create a new, NTFS partition: fdisk /dev/sda n (for new) p (for primary) 3 (for partintion number) "No free sectors available" All the HDD was formatted couple of minutes before so there is a lot of free space but how to resize a parition? I cannot find an option for resizing in man fdisk. Some people say I should use gparted but my distro doesn't not contain this package. And my distro doesn't support wireless drivers so I have serious problems with downloading stuff. I tried also using cfdisk but any command results in: "cfdisk bad primary partition 1 partition ends in the final partial cylinder" I tried also removing partition 1 and then creating a new one (so there is no "no free sectors"). I'm receiving a warning: "Re-reading the partition table failed with error 16: Device or resource busy. The kernel still uses the old table. The new table will be used at the next reboot." After restating: "grub rescue, no known filesystem" It may indicate that some changes have been made BUT when running Windows 7 installed some another error: "Windows cannot be installed to Disk 0 Partition 1" More detailed: "Windows cannot be installed to this hard disk space. Windows must be installed to a partition formatted as NTFS." So formatting drive using Windows 7 installer BUT this time yet another error: "Setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information" Apparently I cannot access logs (how?) and I am back to drawing board with my live USB (this time showing partition as HPFS/NTFS). Any suggestions how to install Windows 7? Should I reinstall Linux to HDD, erase existing partitions once again, and use Parted rather than gparted (parted is included in the distro). Or maybe should I create another bootable USB such as PartedMagic to painlessly create partitions? I just want to install Windows 7 from USB, my laptop is semi-operational and I am ready to receive some help regarding fdisk and creating NTFS partitions. UPDATE: I did as suggested (removed all the partitions) and tried to install in unallocated space. Tried to create a new partition and format it. Same error: "setup was unable to create a new system partition" Came to the conclusion it may have something to do with TrueCrypt I have recently installed. Right now trying to FIX MBR (as I haven't got possibility to create rescue disc without optical drive)

    Read the article

  • What Iptables rules need I to forward a windows remote desktop connection?

    - by avastreg
    I have this situation: network mask. 255.255.255.0 router/gateway: Ubuntu server (only command line, no gui) with internal lan ip 192.168.0.2 and a dynamic dns on the external ip Windows pc on 192.168.0.1 with RDP (remote desktop connection) enabled on 3389 I want to forward the RDP service on the external address: how can i do that? What are the iptables rules I need to connect to my Windows pc from the outside world?

    Read the article

  • BSOD constantly with same ntoskrnl.exe error and disk indicator is frozen

    - by Sheep
    BSOD constantly and the disk indicator is frozen. Error do not happen immediately, usually an hour after boot up. Here is the Minidump: Bug Check Code = 0x00000124 Caused By Driver = ntoskrnl.exe Caused By Address = ntoskrnl.exe+4b094c Crash Address = ntoskrnl.exe+4b094c Seems to be hardware problem, but I checked RAM, no error. I have two HDs installed, system is on SSD, data is on HDD. Checked SSD with the properties-tools-error-checking , no error. Re-installed several times, still happens even after removed HDD. Configuration: SSD: Crucial M4-CT064M4SSD2 with Firmware 0009 Intel HM65 CPU: i7-2630QM The SSD is set correctly, SATA III 6Gb/s enabled, and everything worked perfectly for nearly a year.

    Read the article

  • Upgrading Fedora 16 to 17 with crypted LVM

    - by nijansen
    As the title suggests, I want to upgrade Fedora 16 to the Fedora 17 Alpha build, but I am struggling to do so because of my crypted HDD. To avoid the hustle of CD-ROM or USB install, I thought the preupgrade would be a good idea. It downloads the stuff, stores an image somewhere and creates an entry in my boot manager. When I choose to upgrade from the boot manager it crashes halfway through because it can not access any of the prepared files (because it's crypted) and hands me a debug console. Unfortunately, this case apparently is not covered by the Fedora troubleshooting advice, at least I was not able to find anything there. I would guess I have to mount my HDD manually, but 1) how? and 2) how do I resume the upgrade afterwards? I would really appreciate a push in the right direction.

    Read the article

  • PC doesn't power up anymore

    - by Andrew
    I will tell you the story behind the problem. The computer needed to be reinstalled, it has 2 HDDs so I had to un-plug one to see which is which, to save as much data as possible. After unplugging the first one, it booted with the reinstallation CD, it wasn't the HDD I was looking for so I turned it off and unplugged the other one. After unplugging and turning on, right after booting test, the HDD was turned off, only the CPU fan was working. Turned it off with the power supply's button help, holding the power button didn't do it. And now it doesn't want to turn on anymore. I tried with another test power supply but the result is the same, doesn't want to turn on. Any idea?

    Read the article

  • How to uninstall AMD Display Driver from other install of Windows

    - by nar
    So my Windows 7 had a BSOD from an Ati driver file then restarting only gives me some wierd coloured lines at the top of the screen. Starting in safe mode causes the boot up to freeze at AtiPcie.sys and overlays the same coloured lines on the safe mode start up display. It seems to be a problem with the display driver but I can't get into the OS at all to uninstall it. Luckily I have an old install of Windows 7 from when I moved to a SSD still on my HDD and that runs just fine so I'm pretty sure its a software problem (Maybe the SSD corrupted a driver file or something). So does anyone know how I can uninstall the driver files from another Windows 7 install on the same PC? EDIT: What I mean is, I'm running on the broken PC right now but using a different HDD's windows install. I have full access to the not booting up OS drive with the Windows so I can delete any files/load the registry etc...

    Read the article

  • which drive do I mount

    - by Crash893
    I have a system hdd then two raid1 hard drives I see that sda1 is the system drive but when i do a fdisk -l I get the following results so which of the following do i need to mount to get the "raid" drive and not the individual hdd? root@Mxxxx-PDC:/etc/samba# fdisk -l Disk /dev/sda: 251.0 GB, 251000193024 bytes 255 heads, 63 sectors/track, 30515 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x000762dc Device Boot Start End Blocks Id System /dev/sda1 * 1 30328 243609628+ 83 Linux /dev/sda2 30329 30515 1502077+ 5 Extended /dev/sda5 30329 30515 1502046 82 Linux swap / Solaris Disk /dev/sdb: 400.0 GB, 400088457216 bytes 255 heads, 63 sectors/track, 48641 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 48641 390708801 83 Linux Disk /dev/sdc: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x0009f4b2 Device Boot Start End Blocks Id System /dev/sdc1 * 1 255 2048256 fd Linux raid autodetect /dev/sdc2 256 30401 242147745 fd Linux raid autodetect Disk /dev/sdd: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x000b7f4c Device Boot Start End Blocks Id System /dev/sdd1 * 1 255 2048256 fd Linux raid autodetect /dev/sdd2 256 30401 242147745 fd Linux raid autodetect

    Read the article

  • Extended desktop problem

    - by 08Hawkeye
    I'm a little embarrassed I can't seem to fix this issue: Running a Dell D630 laptop with a VGA to an external monitor. Every time the computer goes to sleep the Dualview setting reverts to single display. I click the Nvidia dualview setting again but the external monitor remains black screen. The only way I can get it working again is to restart :(. What's going on here?? thanks yall //sw

    Read the article

  • Disadvantages of enabling AHCI after Win7 install

    - by Mario De Schaepmeester
    I've formatted my notebook that has a 5400RPM HDD with ~500GB capacity. After installing Windows 7 and about half the drivers (including chipset) I began to doubt whether to go for IDE or AHCI mode for my hard drive. There used to be a lot of discussion on the internet which is better and so far I understood it was particularly helpful on SSDs. Now the general consensus seems to be that AHCI mode is best for most hard drives. I have thus enabled AHCI in the middle of configuring my notebook (rest of the drivers, necessary software etc...) Two questions: considering my HDD's spec above, should I leave it on? Is there any disadvantage of enabling it after Windows 7 and chipset drivers installation? Windows 7 version is 64 bit Home Premium.

    Read the article

  • Use same url externally as internally

    - by Nifle
    If I have a web server on my home network I can connect to it from work with http://my.external.ip/whatever/ (assuming NAT and forwarding). Naturally I have a bookmark in my browser that points to http://my.external.ip/whatever/ however when I use that bookmark on my home computer (also behind NAT) the link does not work because my firewall blocks it. (firewall is a old'ish Dlink) What is the best way to fix this issue?

    Read the article

  • Backing NTFS hard drive to a Linux distro

    - by Ricardo Ferreira
    Hey all, I want to move to Linux (Ubuntu more specifically) and also bought a new hard drive. What I'm not really sure about is if I put my old hard drive on an external case, then install Ubuntu on the new one and configure, etc... Can I easily access my old one (which is now an external hard drive)? Will I have no problems accessing my partitions? Thanks in advance.

    Read the article

  • Taskbar on secondary monitor in XP?

    - by Hemal Pandya
    I am looking for a free virtual-desktop program that will allow me to put a different virtual desktop on each of my two monitors (one on laptop and the other external) How I would like to use it: I do a lot of work connecting to other servers using remote desktop. I would like to use the external monitor to open remote desktop in full screen and use the laptop monitor for the local machine to view my mails, chat, browser, etc. I am using XP SP3.

    Read the article

  • Sorting out mSSD acceleration on a Acer M3-581TG

    - by PhonicUK
    I recently purchased a Acer Timeline M3 Ultra, it ships with a 500GB HDD and a 20GB mSSD to use as a cache. First thing I did when I got it was format the drives and install a clean OS (on the HDD, the mSSD has nothing on it) - but now I can't figure out how everything needs to be configured in order to use the mSSD as a cache, it just looks like a standard storage drive. I've poked around in the BIOS and there is a SATA mode setting, but it only has one option (AHCI), most of the documentation I've seen on the subject says that the SATA controller needs to be in RAID mode otherwise 'Acceleration' isn't visible in the Intel SRT menu (which for me, it isn't) I've seen a few things that suggest I just need the correct partition layout, I tried this using fdisk from a Linux LiveCD but got nowhere. Any ideas? The laptop shipped with no recovery media so I'm marginally stumped. I don't have any issue with reformatting again if required.

    Read the article

  • Finding optimal ddrescue command line options where Accuracy > Speed

    - by gav
    I'm read up a bit about this tool and obviously looked at the man pages. The trouble is that ddrescue takes so long I need to get the command right first time. I wasn't sure how to improve on the vanilla; $ sudo ./ddrescue -v /dev/disk0s5 MyVolImage.dmg MyVolRescue.log $ sudo ./ddrescue -v MyVolImage.dmg /dev/disk1s3 MyVolRestore.log From HSF+ to HSF+ drives Source (Broken) HDD is connected via USB 2.0 Dest HDD is inside MacBook I would choose accuracy over speed There seem to be a lot of options but I'm not sure how they impact quality and speed of recovery. Thanks, Gav

    Read the article

  • How to avoid copying corrupted files with rsync

    - by Roberto Aloi
    I have an HDD with plenty of files, some of which are unfortunately corrupted. I'm now trying to copy the good files into a new HDD. I'm using: rsync -azP SRC TGT When rsync comes to one of the corrupted files, I can see a message in the console: rsync: read errors mapping XXX: Input/output error (5) In the target folder, I still see the corrupted file, which I'm not able to open and which I have to delete manually. Is there any option to tell rsync not to copy files after a i/o error?

    Read the article

  • Windows 7 - Windows 8 dual boot installation error

    - by Nikhil
    I am trying to dual boot Windows 8 with Windows 7 . But I keep getting an error while selecting the drive to install on . The error is ""Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information." " . What might be the problem ? Also previously I tried to install only Windows 7 on my HDD . I downloaded the ISO from digital river . Made bootable usb . I got the same above error . But when I tried to install it via other usb which had pirated Windows 7 downloaded from torrents it gave no error . My system config is Motherboard - Gigabyte G41 MT S2P HDD - 160 GB SATA RAM - 8 GB Help !!!

    Read the article

  • VMWare Server guest cannot browse web on Win2008 host

    - by LachlanG
    Cannot browse the web from the guest VM. Host Windows 2008 R2 web edition Fresh install default firewall settings unchanged VWare server 2.02 Can ping external sites Can resolve DNS hostnames Can browse web Guest VMware NAT networking Win 2000 server No firewall Can ping external sites Can resolve DNS hostnames "Page cannot be displayed" errors when browsing web Could previously browse web when Guest VM run on Win2003 host

    Read the article

  • Is it better to always purchase as much as higher in Watts SMPS, for PC?

    - by metal gear solid
    Is it better to always purchase as much as higher in Watts SMPS, for PC? Does higer watts SMPS also consume more power (electricity bill)? How to know how much watts of SMPS we should purchase? What are factor who decide how much watt of power will need? I'm going to purchase a new Motherboard + CPU + HDD + RAM + DVD Wrtiter + SATA 500 GB HDD ? I'm not purchasing any external Graphic Card. How to decide which watt of SMPS ,I should purchase?

    Read the article

  • What ports does Management Studio use to connect to SQL Server (2005)

    - by Martin
    I have SQL Server 2005 operating on a remotely hosted server and wish to access it from my own machine using management studio The firewall on the remote server is allready setup to allow all traffic from my external IP - and that works great. However I have a load balancing router that has a second line attached to it - unfortunatly the second line has a dynamic external IP. I need to therefore set up a rule in the router to always send data from Management studio on the first line - but I need to know the port numbers. Can you advise?

    Read the article

  • How can I fix an inconsistent NTFS file system without Windows?

    - by Demetri
    I have a Dell laptop that came with Windows from the factory. Since then, I have installed Linux and replaced the hard drive with an SSD. The NTFS partition is inconsistent (a result of bad sectors on the HDD) and needs to be fixed, but I cannot boot into Windows to run chkdsk. How do I fix this problem? Until I do, I cannot move my NTFS partition to expand space on my root filesystem, which is critically low. EDIT: All of my partitions were cloned from my dying HDD to my SSD via Clonezilla. There are no bad sectors on the SSD, but the NTFS partition is still in an inconsistent state.

    Read the article

  • Alienware m15x (older model) BSOD investigation

    - by Crishu
    A frined of mine asked me to help him with an Alienware m15x laptop that had a little service history. It was bought in june 2008, serviced in january 2009 for a random fps drop problem, Alienware returned it saying nothing was wrong. The laptop still had hiccups, but after juggling a few drivers and settings, the fps drops weren't as noticeable. Eventually it died in Sept. 2009. It would not boot up locking itself on a white/gray screen. (i think it was overheating .. clocking in 100 degrees Celsius). So back to Alienware it went. They replaced the GPU and all was fine. Up until these blue screens started showing up. One other thing that was updated was the HDD and a Windows 7 reinstall, in August. From then on it seems to have started its BSOD. Could this be the culprit? Why? 0_o The original Windows was Vista but it was upgraded with a digital download/purchase of Windows 7 Home Premium and activated after installing windows. No errors on the old HDD, just on the latest installation. LE:Due note that now the old HDD is used to see if issues re-occur. So please, I am in need of someone who can interpret these windows dump files: Minidump I may have come to some conflicting conclusions. So if someone can clarify each dump/date and the probable cause/error it had; and a final conclusion or solution, we would be very grateful. Also please consult report for other system info I omitted: same link,code: XRWIVLWG If I missed something or if you have any other questions I'll be happy to answer them. Thank you. Good day. Processor: Intel(R) Core(TM)2 Duo CPU T9300 @ 2.50GHz Network Adapter Properties: Broadcom NetLink (TM) Gigabit Ethernet Intel(R) Wireless WiFi Link 4965AGN Video Adapter Properties: Driver Description NVIDIA GeForce 8800M GTX Driver Date 19.08.2009 Driver Version 8.16.11.8681 Driver Provider NVIDIA INF File oem19.inf Hardware ID PCI\VEN_10DE&DEV_060C&SUBSYS_0770152D&REV_A2 Location Information @system32\DRIVERS\pci.sys,#65536;PCI bus %1, device %2, function %3;(1,0,0) PCI Device NVIDIA GeForce 8800M GTX [NoDB] BIOS String Version 62.92.34.0.8 Installed Drivers nvd3dum (8.16.11.8681), nvwgf2um, nvwgf2um Hard Dik Drive: Model ID ST9120823ASG (**older one 120gb**) Model ID WD32000BEKT (new 320gb with fresh OS)

    Read the article

  • Laptop Locking Up

    - by David
    I am having a very weird issue on a Lenovo W510 laptop. It will lock up randomly. I have had it lock up during post, during the boot-up of Linux, during login, and after the login. The following are tests that I have performed on the laptop. I ran memtest I took out the extra memory module. I swapped the HDD with another HDD that had Windows 7 on it. (It BSOD'd, and before anyone could possibly read the error line, it restarts.) I tried taking the battery out and booting with only the Power cord. The only other options I can think of the problem being are the motherboard or the PSU. If anyone has any advice, I appreciate it. If not, the HP guy will be here in a few days to fix it. I would just love to call them up and tell them that the service is no longer needed.

    Read the article

  • C drive should only contain OS. Myth or fact?

    - by Fasih Khatib
    So, I have a 500GB HDD @7200RPM. It is split as: C: 97GB D: 179GB E: 188GB My belief is to keep OS ONLY in C:\ and any adamant programs that won't go anywhere apart from C:\ [because this speeds up the PC during startup process] and install programs in D:\ so that in case I have to reinstall the OS, I will have the programs readily available after reinstall. But I have begun to think this approach is flawed because if C:\ is formatted, I will lose registry values and stuff that goes in %appdata% and so it is no use keeping programs in D:/ drive because they will be useless after all. Should I go ahead and install ALL of my programs in C:\ and then use D:\ and E:\ for storing my data like photos, text files, java files n all? How will this impact the performance of the HDD? I only have 3 programs in D:\Program Files so it will be easy to reinstall them :)

    Read the article

  • File copying software to do this kind of work... in Windows 7 32 bit

    - by Senthil
    I need a software (Windows 7 32bit) to help me in this process: I have my documents, music, video clips, movies, pictures in my hard disk. These will not be scattered around the system. But will be inside C:\Senthil\ At the end of every week, I want to plug in an external hard disk and run a software that should make sure whatever is inside C:\Senthil\ is also present in the external disk. Files deleted from C:\Senthil\ should be deleted there, and new files should be copied etc... at the end of the process, every bit inside the source folder in my internal disk should be inside my external disk. A couple of important requirements and points: I do NOT need multiple versions or historic versions. I don't need the previous versions of my files. I only want the latest copy to be present in my "backup". Incremental backup makes sense. If files were not touched since the last backup, it need not copy. The size of my folder will run into GBs and in a year or two will go into TBs. But I will make sure the size of the external HDD is equal to or bigger than my source folder. I do not want it to run automatically because when I accidentally delete a file in my source, it will delete the one in the backup (I know this is why we have versioning facilities). I just want to be able to run it manually so that I am in control of when the backup is made and what is backed up and I should be able to pick something from the backup and restore it to the source folder in the above situation. Is there any software that will let me do exactly this? I don't want any other "smart" facility of the software to interfere with this process. I know what I want and the software can keep its smartness to itself :D The main reason I am asking this question is, I am a software developer and I can write this software myself. But I am a little constrained by time at the moment and I want to know if there is an existing program that can do this. Kindly don't worry about earthquakes or fire or snowstorms and bring up the "in case of a natural disaster your backup will also be in the damage zone and will be lost" argument because: I will have bigger things to worry about than my holiday memories. I don't think I will digitally store any life-ruining documents. This backup is only to avoid the inconvenience of obtaining a new copy of stuff that I have. Not to protect them against the end of the world. I am more worried about power surges in my area frying my system, hard disk failure, children who merrily hit Delete or teens who hit Shift + Delete or myself getting a little careless at times! In short: Is there a file/folder syncing software that listens to what I say and doesn't try to act smart? Please forgive me if I sound arrogant :)

    Read the article

< Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >