Search Results

Search found 29432 results on 1178 pages for 'mite fine dailes'.

Page 114/1178 | < Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >

• iwlwifi on lenovo z570 disabled by hardware switch

  - by Kevin Gallagher

  It was working fine with windows 7. The hardware switch is not disabled. I've toggled it back and forth dozens of times. The wifi light never turns on and it always lists as hardware disabled. I have the latest updates installed. I've been searching for solutions, but none of them seem to work for me. I've tried removing acer-wmi. I've tried setting 11n_disable=1. I've tried resetting the bios. I've tried using rfkill to unblock (only removes soft block). I've rebooted dozens of times. The wifi light turns off as soon as grub loads. Edit: I have a usb edimax wireless nic. It shows hardware disabled as well (although rfkill lists as unblocked). If I unload iwlwifi the usb nic works fine. uname -a `Linux xxx-Ideapad-Z570 3.2.0-55-generic #85-Ubuntu SMP Wed Oct 2 12:29:27 UTC 2013 x86_64 x86_64 x86_64 GNU/Linu`x rfkill list 19: phy18: Wireless LAN Soft blocked: no Hard blocked: yes dmesg [43463.022996] Intel(R) Wireless WiFi Link AGN driver for Linux, in-tree: [43463.023002] Copyright(c) 2003-2011 Intel Corporation [43463.023107] iwlwifi 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [43463.023190] iwlwifi 0000:03:00.0: setting latency timer to 64 [43463.023253] iwlwifi 0000:03:00.0: pci_resource_len = 0x00002000 [43463.023257] iwlwifi 0000:03:00.0: pci_resource_base = ffffc900057c8000 [43463.023261] iwlwifi 0000:03:00.0: HW Revision ID = 0x0 [43463.023797] iwlwifi 0000:03:00.0: irq 43 for MSI/MSI-X [43463.024013] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [43463.024250] iwlwifi 0000:03:00.0: L1 Enabled; Disabling L0S [43463.045496] iwlwifi 0000:03:00.0: device EEPROM VER=0x15d, CALIB=0x6 [43463.045501] iwlwifi 0000:03:00.0: Device SKU: 0X50 [43463.045504] iwlwifi 0000:03:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [43463.045542] iwlwifi 0000:03:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [43463.045744] iwlwifi 0000:03:00.0: RF_KILL bit toggled to disable radio. [43463.047652] iwlwifi 0000:03:00.0: loaded firmware version 39.31.5.1 build 35138 [43463.047823] Registered led device: phy18-led [43463.047895] cfg80211: Ignoring regulatory request Set by core since the driver uses its own custom regulatory domain [43463.048037] ieee80211 phy18: Selected rate control algorithm 'iwl-agn-rs' [43463.055533] ADDRCONF(NETDEV_UP): wlan0: link is not ready nm-tool State: connected (global) - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: unavailable Default: no HW Address: 74:E5:0B:4A:9F:C2 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points lshw -C network *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 74:e5:0b:4a:9f:c2 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-55-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:43 memory:f1500000-f1501fff lspci 03:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak]

  Read the article

• Why won't this application start when I log in?

  - by George Edison

  I have a file in ~/.config/autostart/ that looks like this: [Desktop Entry] Type=Application Exec=python ~/Documents/StackApplet/stackapplet.py Icon=/usr/share/pixmaps/stackapplet.png Terminal=false Comment=a panel indicator for monitoring StackExchange sites Name=StackApplet Categories=Utility; Unfortunately, it isn't working - the application is not starting when I log in. If I open a terminal and copy-and-paste the command listed in Exec above, then the application runs just fine. What am I doing wrong?

  Read the article

• problem after login in wordpress site

  - by pankaj sharma

  I have installed WordPress first installation on Apache server Its opening fine but when i logged in with my user id and password http://examplesite.com/wp-login.php It is showing blank in Firefox and in IE page not open with no errors. I cleared all my browsers cache history still not able to open the page after login. There is no errors logs generated. wordpress version3.4.2 php 5.3.3 mysql 5.1.6

  Read the article

• Criteria for selecting timeout value?

  - by stijn

  Situation: a piece of software reads frames of data from a file in a seperate thread and puts it on a queue, emptied by another thread. That second thread periodically checks on the queue and fails rather gracefully, by showing an error message stating the read timed out, if no data is available within a certain amount of time. Initially this timeout was set to 200mSec. There was no real reasoning behind that constant though, but it worked fine. We measured on a couple of machines and for large data frames, larger than what would be used by customers, a read took like 20mSec whith no other load on the machine. However one customer now gets timeout errors now and then (on the second try all is fine, probably the file is in cache or the virus scanner leaves it alone). The programmers are like 'well, yeah, but that customer's machine is full of cruft, virus scanners, tons of unneeded background processes etc'. Of course the customer is like 'hey this should just work, shouldn't it'? While the programers have a point, since the software is heavy enough to validate the need for a dedicated machine, that does not make the customer happy. Increasing the timeout to 2 seconds, for example, solves the problem. But I'd like to make a proper decision now instead of just randomly pick some magic constant that is probably ok in 99% of cases. What criteria should be used for that? We could just pick a large number, but that feels wrong. (and then we end up with a program that has the horrible bahaviour of hanging when trying to read from a disconnected drive for instance, whereas we'd rather make it show an error right away). Or we could make the timeout value a user setting, but then we need to ducument it clearly and even then not all customers are tech savy enough to really understand what it does. Or we could try and wait until another customer reports timeouts and increase the value again. And again. Until we find something ok for 99.99% of the cases.. Any good practice for this type of situation?

  Read the article

• bought computer with ubuntu program messed up

  - by linda stecker

  i recently got a dell inspiron B130 with an ubuntu prgm on it and the main users desktop is scattered allover the place , files everywhere but not in folders,how do i fix this? i am new working with this operating system ,used to windows versions. if i go into a guest profile the desktop is perfectly fine and everything works but i cannot make the system fix itself or don't really know where to start help??????? i have the user name and password and can get to terminal screen , but not sure how to remove and add myself to admin use

  Read the article

• HTG Explains: Do You Really Need to Safely Remove USB Sticks?

  - by Chris Hoffman

  You’ve probably heard that you always need to use the Safely Remove Hardware icon before unplugging a USB device. However, there’s also a good chance that you’ve unplugged a USB device without using this option and everything worked fine. Windows itself tells you that you don’t need to use the Safely Remove Hardware option if you use certain settings – the default settings – but the advice Windows provides is misleading. How to Use an Xbox 360 Controller On Your Windows PC Download the Official How-To Geek Trivia App for Windows 8 How to Banish Duplicate Photos with VisiPic

  Read the article

• Opening / using WUBI after downloading

  - by Jon

  I have no problem downloading WUBI either using Firefox or IE. Either way, however, when I try to run or open it, I get a message to the effect that the file cannot run because the configuration is incorrect and "re-installing the file may help" (which it doesn't - I've tried several times). What am doing wrong ? I am running XP Pro. (Note: my Ubuntu CD works just fine but I want to install Ubuntu inside Windows).

  Read the article

• Why no icons for pcmanfm when run from remote x server

  - by user75430

  pcmanfm works fine when run from a local console, but does not show file icons when run from a remote x session (ssh -X user@machine). Well, that's not quite true - icons for shell scripts show up OK, there are no icons for regular files and folders. There are a load of errors in the X console window "g_object_unref ... G_IS_OBJECT". Why are there no icons for pcmanfm when I run it from a remote x server?

  Read the article

• No suspend on lid closing on a Samsung Series 5 14" NP530U4BI

  - by dmeu

  Ok, i realize I am not the only one, but I will try to provide all info possible to make it exemplary as possible and narrow down the error sources. I have a fresh install of Ubuntu 12.04 and the suspend worked fine upon having it freshly installed but now it does not anymore. The suspend option from the system power button on the top right works fine. Things I did do which I don't know if they are related: Install and remove againthe FGLRX drivers (Radeon graphic card) Install Jupiter power managment (shutting it down is not changin anything) Plug in and out an external display The configuration I know of is well set: In System Settings/Power all is set to suspend when closing lid Double checked with dconf-editor, everything set to suspend So, from here on I don't know how to proceed.. what are common problems that cause this error? EDIT: My computer model is: Samsung Series 5 14" NP530U4BI $ sudo lspci -nn 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller 00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller 00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller 00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 00:1c.3 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 00:1f.0 ISA bridge [0601]: Intel Corporation HM65 Express Chipset Family LPC Controller [8086:1c49] (rev 04) 00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller 00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 04) 01:00.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI Thames [Radeon 7500M/7600M Series] 02:00.0 Network controller [0280]: Intel Corporation Centrino Advanced-N 6230 03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller 04:00.0 USB controller [0c03]: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller

  Read the article

• Windows 7 SP1 now available

  - by guybarrette

  I installed the SP1 for Windows 7 yesterday on two machines.  Short story: nothing to report, everything went fine. Looks like this is a “real” service pack meaning that what it does is install all the fixes and updates released since the Windows 7 release.  It does introduce a few new features.  For a complete list, check the “Notable Changes...” document found here. var addthis_pub="guybarrette";

  Read the article

• Java 1.7 update 07 and Google Chrome

  - by Peter

  I've just updated Java from 1.6 to 1.7 via the Software Centre - removing the old Java 1.6 and selecting the new Java 1.7. Firefox works fine. But when I use Google Chrome to access a Java test website it says the Plugin is out of date. I click on run anyway and it says that it's running version 1.7. I've cleared Chrome's Cache and Plugin data and this hasn't changed anything. Anyway ideas? (Ps. It's Ubuntu 12.04 64 bit)

  Read the article

• Moving to a custom domain in blogger spoiled my pagerank. Need help?

  - by Chankey Pathak

  I had www.chankeypathak.blogspot.com as my blog on Blogger. I then purchased a domain www.chankeypathak.com and then I followed the procedure of redirecting all old pages to new ones (301 redirect). Everything is working fine. But the only problem is that I have lost my pagerank. before it was 2 for www.chankeypathak.blogspot.com and now it is showing unranked for www.chankeypathak.com How can I get my pagerank back?

  Read the article

• Mixed java version installed

  - by david99world

  I've got the following in /.bashrc export JAVA_HOME=/usr/bin/jdk1.7.0_03/ export PATH=$PATH:/usr/bin/jdk1.7.0_03/bin This is fine, if I do $JAVA_HOME I get the directory above. The problem is if I do java -version I get... OpenJDK Runtime Environment (IcedTea6 1.11.1) (6b24-1.11.1-4ubuntu3) OpenJDK 64-Bit Server VM (build 20.0-b12, mixed mode) How do I make the official jdk version the right one? Sorry I'm extremely new to Ubuntu. Thanks, David

  Read the article

• T-SQL bits - ROW_NUMBER

  - by MartinIsti

  About a month ago I found the SQLShare site which provides useful, clear tutorial videos of how to use some SQL functions, or how to fine tune a query. Their videos are roughly 3-5 minutes long and have proved to be very good for me with a strong BI background with less first-hand T-SQL experience. I decided to make notes of the ones I watched and found useful and instead of putting them into a word document somewhere locally I'll publish them on this blog so. These would be very simple and short...(read more)

  Read the article

• How do I compile & install the newest version of Transmission?

  - by Codemonkey

  I'm trying to install Transmission 2.51 on Ubuntu 10.04. Compiling the source goes fine, but I can't seem to get it to compile the GUI as well. This is the configure output: Configuration: Source code location: . Compiler: g++ Build libtransmission: yes * optimized for low-resource systems: no * µTP enabled: yes Build Command-Line client: yes Build GTK+ client: no (GTK+ none) * libappindicator for an Ubuntu-style tray: no Build Daemon: yes Build Mac client: no How do I get it to build the GTK+ client?

  Read the article

• Parallel Port Problem in 12.04

  - by Frank Oberle

  I have a “dumb” printer attached to a parallel port in my machine which works fine under the “other” resident operating system (from Redmond) on the same machine. I recently added Ubuntu 12.04 as a dual boot on the machine, but Ubuntu doesn't seem to recognize the parallel port at all. All I need to set up a printer is a really plain-vanilla fixed pitch text-only generic driver, which is present, but no parallel ports show up. (The other printers, all on USB ports, seem to work just fine). Following what appeared to me to be the most reasonable of the many conflicting pieces of advice on the web, here's what I did: I added the following lines to /etc/modules parport_pc ppdev parport Then, after rebooting, I checked to see that the lines were still present, and they were. I ran dmesg | grep par and got the following references in the output that seemed like they might have to do with the parallel port: [ 14.169511] parport_pc 0000:03:07.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 14.169516] PCI parallel port detected: 9710:9805, I/O at 0xce00(0xcd00), IRQ 21 [ 14.169577] parport0: PC-style at 0xce00 (0xcd00), irq 21, using FIFO [PCSPP,TRISTATE,COMPAT,ECP] [ 14.354254] lp0: using parport0 (interrupt-driven). [ 14.571358] ppdev: user-space parallel port driver [ 16.588304] type=1400 audit(1347226670.386:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=964 comm="apparmor_parser" [ 16.588756] type=1400 audit(1347226670.386:6): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=964 comm="apparmor_parser" [ 16.673679] type=1400 audit(1347226670.470:7): apparmor="STATUS" operation="profile_load" name="/usr/lib/lightdm/lightdm/lightdm-guest-session-wrapper" pid=1010 comm="apparmor_parser" [ 16.675252] type=1400 audit(1347226670.470:8): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/mission-control-5" pid=1014 comm="apparmor_parser" [ 16.675716] type=1400 audit(1347226670.470:9): apparmor="STATUS" operation="profile_load" name="/usr/lib/telepathy/telepathy-*" pid=1014 comm="apparmor_parser" [ 16.676636] type=1400 audit(1347226670.474:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/cups/backend/cups-pdf" pid=1015 comm="apparmor_parser" [ 16.677124] type=1400 audit(1347226670.474:11): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/cupsd" pid=1015 comm="apparmor_parser" [ 1545.725328] parport0: ppdev0 forgot to release port I have no idea what any of that means, but the line “parport0: ppdev0 forgot to release port ” seems unusual. I was still unable to add a printer for my old clunker, so I tried the direct approach, typing echo “Hello” > /dev/lp0 and received a Permission denied message. I then tried echo “Hello” > /dev/parport0 which didn't give me any message at all, but still didn't print anything. Running the command sudo /usr/lib/cups/backend/parallel gives the following: direct parallel:/dev/lp0 "unknown" "LPT #1" "" "" Checking the permissions for /dev/parport0, Owner, Group, and Other are all set to read and write. crw-rw---- 1 root lp 6, 0 Sep 9 16:37 /dev/lp0 crw-rw-rw- 1 root lp 99, 0 Sep 9 16:37 /dev/parport0 The output of the command lpinfo -v includes the following line: direct parallel:/dev/lp0 I've read several web postings that seem to suggest this has been a problem for several years, but the bug reports were closed because there wasn't enough information to address the issue (shades of Microsoft!). Any suggestions as to what I might be missing here?

  Read the article

• Midori displays mobile sites.

  - by Tigull

  I've installed Midori to work in an Elementary mockup. Midori works just fine, but, on a few domains, it opens mobile websites instead of the regular pages. A of now, this happens with gmail.com, facebook.com, paginegialle.it, and others; yet other websites which do have a mobile version, as gazzetta.it, show the regular version. I couldn't find a solution through settings and I didn't find any mention of this problem on forums or else, so any help would be greatly appreciated.

  Read the article

• How can Nautilus autodiscover a NAS?

  - by Private

  I have two machines: a 12.10 which autodiscovers my NAS fine and a 13.04 which does not autodiscover the NAS in Nautilus. The latter does not display the drive in Nautilus. I did install samba on the 13.04, I think a while ago, but I cannot remember what I did. Before I connected to the drive using afp, now I notice the 12.10 uses smb. How can I make my 13.04 autodiscover the NAS and how should I configure it?

  Read the article

• WebLogic Server internal server error [migrated]

  - by Abhinav Pandey

  When I deployed a project in Apache Tomcat 6.0 it is working fine. When I deployed a same project in WebLogic Server 10.3 it's showing an error: Error 500--Internal Server Error javax.servlet.ServletException: [HTTP:101249][weblogic.servlet.internal.WebAppServletContext@ae43b8 - appName: '_appsdir_ab_dir', name: 'ab', context-path: '/ab', spec-version: 'null']: Servlet class FirstServlet for servlet FirstServlet could not be loaded because the requested class was not found in the classpath . java.lang.UnsupportedClassVersionError: FirstServlet : Unsupported major.minor version 51.0.

  Read the article

• Mount drive on remote machine

  - by NikolaiDante

  My current set up is: I have my main machine (Darkseid) upstairs which has a drive with all my films on it, which I don't keep mounted. Downstairs, next to the tv, I have a htpc (Archangel) which has xbmc installed on it, which points to a samba share on the main machine. Everything works fine when the drive is mounted, but is there a script I can write to send a command to the upstairs machine from the downstairs machine to mount the drive to save the walk upstairs? #lazy Both machines are Ubuntu 12.04

  Read the article

• Error occurred in deployment step 'Recycle IIS Application Pool'

  - by shehan

  Encountered this error while trying to deploy a SharePoint 2010 project from Visual Studio 2010:Error occurred in deployment step 'Recycle IIS Application Pool': The open operation did not complete within the allotted timeout of 00:01:00. The time allotted to this operation may have been a portion of a longer timeout.All my other projects in the solution deploy just fine. To fix this, I had to retract the offending project (through Visual Studio) and re-deploy.

  Read the article

• Canon MG8150 - unable to scan document to PC via wireless router, but works via USB connection?

  - by Heidi

  Please help. Get error that scanner disconnected or locked "code:5,146,555" when I try to scan a document to PC or attach to an email. Can't remember this function ever working and I've had this MFD for 2-3 years now. Printer function works fine via wireless, but not scanning. Upgraded my laptop a few months ago from Windows 98 to Windows Vista and reinstalled my printer/scanner software and drivers. Any ideas?

  Read the article

• AMD graphics drivers

  - by user284659

  I have a new laptop with dedicated graphics card and I decided I will go with Ubuntu 14.04. All is just fine and I love it but the repos for graphics drivers from Canonical are just well... old .Is there any problem if I install my graphics drivers from AMD's official website and not from Software Updater? It's just that from there i get the latest and greatest.I read the realease notes and 14.04 is supported.

  Read the article

• Jokes search engine / PHP based search engine on database

  - by matt74tm

  I'm looking for a script, functioning like the Google homepage that fetches data from a database rather than the internet. This is not intended to be a search engine, but a repository of jokes that can be pulled depending on the keywords typed. No sophisticated search techniques are required - keyword based is perfectly fine. If some mechanism of up/down-voting jokes can be incorporated, that would be fantastic, but I'm presuming that will be an entirely different game.

  Read the article

• Cannot Boot Win XP or Ubuntu from hard drive - get Input Not Supported

  - by Jim Hudspeth

  1) Downloaded 11.10 ISO file to Dell XP Workstation 2) Made bootable USB using Pendrivelinux 3) Installed to harddrive using option 1 (Install along side Windows) 4) Rebooted when instructed 5) Booted into Ubuntu just fine (first time) 6) Attempted restart - got first splash screen followed by "input not supported" - tapped ESC and eventually got into Ubuntu 7) Later attempts failed - got "input not supported"; no eventual boot 8) Many retries holding / tapping various keys - same result 9) Booted from USB - all files appear to be in place - can access GRUB on harddrive Suggestions appreciated - must to be able to boot XP. Thanks in advance

  Read the article

< Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >