Search Results

Search found 11687 results on 468 pages for 'ex networking guy'.

Page 115/468 | < Previous Page | 111 112 113 114 115 116 117 118 119 120 121 122  | Next Page >

• Force local IP traffic to an external interface

  - by calandoa

  I have a machine with several interfaces that I can configure as I want, for instance: eth1: 192.168.1.1 eth2: 192.168.2.2 I would like to forward all the traffic sent to one of these local addresses through the other interface. For instance, all requests to an iperf, ftp, http server at 192.168.1.1 should be not just routed internally, but forwarded through eth2 (and the external network will take care of re-routing the packet to eth1). I tried and looked at several commands, like iptables, ip route, etc... but nothing worked. The closest behavior I could get was done with: ip route change to 192.168.1.1/24 dev eth2 which send all 192.168.1.x on eth2, except for 192.168.1.1 which is still routed internally. May be I could then do NAT forwarding of all traffic directed to fake 192.168.1.2 on eth1, rerouted to 192.168.1.1 internally? I am actually struggling with iptables, but it is too tough for me. The goal of this setup is to do interface driver testing without using two PCs. I am using Linux, but if you know how to do that with Windows, I'll buy it!

  Read the article

• Snow Leopard - resolving hostnames issue

  - by romant

  This worked in Leopard, although since Snowie came along … I have a Location setup with a DNS server to use [eg 10.0.0.17] , and a search string [eg sub.dom.ain.com] In the terminal: $ nslookup cake Server 10.0.0.17 Address: 10.0.0.17#53 Name: cake.sub.dom.ain.com Address: 10.0.0.38 So works like a charm. Although if I just the hostname cake in any other application within OSX - such as Safari/CoRD, they simply can't resolve the hostname. I have to instead use the FQDN cake.sub.dom.ain.com - why is this so? Why did this work in Leopard and is now broken? Would love a solution. Thanks

  Read the article

• Cisco QoS Guidance

  - by Kyle Brandt

  I have a 10M connection to the internet that is hooked into a 100M port. I am getting started with QoS, and am hopping for a little guidance on setting it up on a Cisco 3825 router. Right now I am going forward with the idea that I have to implement it on my router, and the provider can't provide QoS for me. How I envision it working is that the QoS will drop or queue packets on my router and that will help prevent a situation where the provider has to start dropping a lot of packets. Right now all I am tasked with is making sure that one of the 3 LANs gets a certain slice (say 3M for Gig Lan1) of the 10M internet connection (But ideally this will be more flexible in the Future). 10M Internet on 100M port on HWIC-4ESW +-----------------------+ | | Gig Lan1 | Cisco 3825 | Lan3 on HWIC-4ESW | | +-----------------------+ Gig Lan2 I need to learn more about QoS, but having a target technology and maybe example configuration will help me wrap my head around the reading I am doing a little more. Which Cisco QoS Technology do you recommend for this particular situation? Have a basic sample config of how this might work? Right now the 10M line is not congested, so this more to have something in place in case it starts to become mildly congested in the future. I do have VOIP at one location connected to this one over the Internet that goes through a VPN tunnel. Everything else that is between this location and other offices is on a separate MPLS network.

  Read the article

• Win 7 Netbook refuses to ping JetDirect card (all other PCs work)

  - by Luke Puplett

  I have an odd thing occuring here. From a Windows 7 netbook, I cannot ping an HP printer on the network, while all other machines (Win7/Vista) can. And the netbook can also ping everything else on the LAN. Example showing that the netbook can ping 192.168.3.4 but not 3.6. C:\Users\backdoor>ping w7ue1m Pinging w7ue1m.corp.biz.co.uk [192.168.3.4] with 32 bytes of data: Reply from 192.168.3.4: bytes=32 time=7ms TTL=128 Reply from 192.168.3.4: bytes=32 time=4ms TTL=128 Reply from 192.168.3.4: bytes=32 time=2ms TTL=128 Reply from 192.168.3.4: bytes=32 time=2ms TTL=128 Ping statistics for 192.168.3.4: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 2ms, Maximum = 7ms, Average = 3ms C:\Users\backdoor>ping uktnprint1 Pinging uktnprint1.corp.biz.co.uk [192.168.3.6] with 32 bytes of data: Reply from 192.168.3.0: Destination host unreachable. Reply from 192.168.3.0: Destination host unreachable. Reply from 192.168.3.0: Destination host unreachable. Reply from 192.168.3.0: Destination host unreachable. Ping statistics for 192.168.3.6: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),`enter code here` The IPCONFIG result for the netbook is fine. IPv4 Address. . . . . . . . . . . : 192.168.3.0 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : 192.168.1.1 Most unusual network thing I've seen in years. I must reiterate that only this netbook is having trouble pinging/printing. Thanks, Luke ** UPDATE ** Am now on a Vista box, and here's the IPCONFIG: IPv4 Address. . . . . . . . . . . : 192.168.3.3 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . : 192.168.1.1 Pinging uktnprint1.corp.biz.co.uk [192.168.3.6] with 32 bytes of data: Reply from 192.168.3.6: bytes=32 time=2ms TTL=60 Firewall is off. I'll look into the chance of an IP conflict because it's the only thing I can think of - compare arp caches of each machine. Cheers!

  Read the article

• Internet doesn't work when enable local Lan

  - by rakesh yadav

  We have the following network setup: A) Router IP 192.168.51.49 B) Windows Server 2008 R2 with dual NIC: B1) WAN interface (192.168.0.2) ( Used for internet) B2) LAN interface (192.168.1.2) ( used for local connectivity) when i keep both LAN Enabled than my internet doesn't work, but if I disabled my local Lan than internet working fine. so please help me how can resolved this issue or should i need to do routing on my server Please find the below attached route print result C:\Users\Administrator>route print =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.51.49 192.168.51.50 276 0.0.0.0 0.0.0.0 192.168.30.227 192.168.30.228 266 192.168.30.224 255.255.255.240 On-link 192.168.30.228 266 192.168.30.228 255.255.255.255 On-link 192.168.30.228 266 192.168.30.239 255.255.255.255 On-link 192.168.30.228 266 192.168.51.48 255.255.255.240 On-link 192.168.51.50 276 192.168.51.50 255.255.255.255 On-link 192.168.51.50 276 192.168.51.63 255.255.255.255 On-link 192.168.51.50 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 202.56.230.5 255.255.255.255 192.168.51.49 192.168.51.50 21 202.56.230.6 255.255.255.255 192.168.51.49 192.168.51.50 21 192.168.26.124 255.255.255.255 192.168.51.49 192.168.51.50 21 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.51.50 276 224.0.0.0 240.0.0.0 On-link 192.168.30.228 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.51.50 276 255.255.255.255 255.255.255.255 On-link 192.168.30.228 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.30.227 Default 0.0.0.0 0.0.0.0 192.168.51.49 Default ===========================================================================

  Read the article

• Creating an office network and monitoring all activity without a proxy

  - by Robert

  We are setting up our office network and would like to track all the websites visited by our employees. However, we would not like to use any proxy based solutions. Our work is highly dependent on applications in which you cannot configure a proxy. Hence, the approach we would like to follow is setting up a router inside a computer (something like this : http://www.techrepublic.com/article/configure-windows-server-2003-to-act-as-a-router/5844624) This will also allow us to attach multiple ethernet cards and have redundancy in internet connectivity with complete abstraction from the user about which connection is being used. But most importantly, since all the traffic will be going through the computer (configured as a router) I assume there will be a way to run packet analysis on all the request / responses being made. For example, list all the FTP servers connected to (port 21), give a graph of all the URLs visited per day by frequency. Is there already a software which does this ? Or is it possible to build something like this ?

  Read the article

• Why maximum 1.0 Gbit Ethernet connection an old notebook, and only 100 Mbit on newer faster computer

  - by Sam

  Strange problem about Ethernet speed: recently we bought an i7 core computer running Win7 64 bit with an onboard Gigabit Ethernet controller (Realtek PCIe Gbit Ethernet Family controller). Connecting this new fast pc directly to our brand new ASUS Gigabit Ethernet router via CAT6 cable(!) shows up the adapter status (see picture attached) only 100mbit, while the router is capable of 1000 mbit. More facts: Connecting an 8 year old IBM notebook with gigabit ethernet to the same cable end shows 1.0 Gbit connection in its adapter status. Speedtest.net shows 35 mbit/s down on the new computer Speedtest.net shows 78 mbit/s down on the old rusty IBM notebook. We have an 120 mbit down internet connection, which we we truly receive on another pc (also directly connected to the router) How to get the 1.0 Gbit going in the new pc ?

  Read the article

• subnetting a class c on a cisco 3825

  - by Adeodatus

  I have a class C that I want to better understand before I implement a change. Right now, ip address 192.168.0.1 255.255.255.192 ip address 192.168.0.65 255.255.255.240 secondary So, where is the 192.168.0.64 address in that mix? 192.168.0.63 should be the broadcast for the first one, and 192.168.0.65 should be the cisco secondary ip. And ... How then do I add a /28 (255.255.255.240) right before this segment: ip address 192.168.0.249 255.255.255.248 secondary In fact, I'll probably want to add it as a subinterface Can anyone help me to better understand whats going on and then how to do it?

  Read the article

• Vlan and Switch setting - dummy

  - by Andras Sebestyen

  I need to speak tomorrow the network engineer and I would like to understand his so apologise for the Dummy question: In the school we have a cab with a 24 port Netgear manageable switch with an admin and curriculum VLAN settings. Usually, as I over heard, in the morning and around 4.30pm there are a slowdown period on the computers which connect to this switch. No one could track this back yet. Questions: What is the best way to track back this slowdown Would it be a temporary solution to physical separate the two network with 2 switches If that would work how can I link them together to be able to see the curriculum from the admin side. Do I need an extra router then? Too many questions but I have no clue where to start and the gentleman will be paid by hours... can you see where I am coming from?:) Could you guide me in the right direction please? Any comment would be appreciated and please send links if you down vote the question:)

  Read the article

• Different network response for indentical co-located machines

  - by Santosh

  We have a situation as follows: We have a two different virtual machines (VMs) on some remote server farm. The machines are identical in terms of hardware/software(OS) configurations. We have a J2EE application running on JBoss on each of those two machines. These two applications are of different version sav V1 on VM1 and V2 on VM2. We observed some degraded response time for application V2 when accessed via public URL. When we accessed the application through a secured VPN, there is hardly any difference. The bandwidth test (upload/download speed, ping etc) shows that VM1 is responding better when accessed via secured VPN. We concluded that the application does not seem to have performance issue. Because, it that's the case the performance degradation should also be there when access via VPN. So we concluded its the network problem. But since those two identical VMs are on same network we are looking for the reasons for different responses. My question is, given the above situation, what could be reasons for such a behavior ?

  Read the article

• Anyone love/hate the PowerConnect line of switches from Dell?

  - by Rob Bergin

  I am looking at replacing some unmanaged 16 port store bought GB switches and wanted to go with Cisco but it may be cost prohibitive. Instead I am looking at ProCurve or Dell's PowerConnect line up. I am looking for SNMP, Management, VLANs, and SFLOW would icing on the switch cupcake. I would get the 6224 or the 6248 and then maybe add the RPS-600 to it for redundant power. I think the RPS-600 supports multiple switches. Rackspace is also a little challenge so I am trying to do it with as little Rack Units as possible. Ideally I would go with two 6224's or a single 6248 and then do two VLANs. Thanks for any feedback. Rob

  Read the article

• Network connectivity logs on OSX

  - by Stephen

  I'm trying to determine whether or not Macs store a log of network connectivity. Specifically, I'm trying to find out if one of my machines (Mac Tower, OSX 10.7.4, 2-2.26 GHz, 16 GB DDR3) lost connection to pinpoint an issue. This machine is on an external network where and the IT staff is not very helpful, so I'm trying to ensure that there were network issues rather than some other local issue on that particular machine. Can you pull network logs thru Console that show when a network connection was established and was disconnected?

  Read the article

• How to access web server of any machine of my network from the outside

  - by Luc

  Hello, I have an ip like username.dyndns.org, this is the external IP of my router. On my lan, I have several machine (m1, m2, ...) , each running a dedicated web server. Is it possible to reach each machine from the outside with something like: http://m1.username.dyndns.org http://m2.username.dyndns.org ? Do you know what needs to be configured in my router for NAT ? Also, is there a special directive in Apache to do so ? Thanks a lot, Regards, Luc

  Read the article

• Trouble with wireless driver on a Dell Latitude D830

  - by Kevin

  After uninstalling Dell's wireless utility I get a new hardware found dialog that can not find any driver for my wifi card on it's own. I'm running Windows XP Professional Service Pack 3, and I would like to use the default wifi handler since dell's utility does not work with my company's wireless switch. I did try downloading the recommend driver from the dell support site Network Adapter 2 Model Intel(R) PRO/Wireless 3945ABG Network Connection Description [12] Intel(R) PRO/Wireless 3945ABG Network Connection Status Connected

  Read the article

• Ruckus wireless AP and Dell PowerConnect configuration problems

  - by DanielJay

  We are working on trying to get some Ruckus Access Points to work correctly on our network. Currently our network is as follows: VLAN 10 - Servers VLAN 11 – Computers/DHCP VLAN 12 – Voice VLAN 13 – Guest We use Dell PowerConnect 6248P switches for our switches. Port settings are as follows: ZoneDirector 1100 is plugged into this port. Should be accessing the server VLAN and then allowing all other traffic. interface ethernet 1/g2 classofservice trust ip-dscp description 'Ruckus ZoneDirector 1100' switchport mode general switchport general pvid 10 switchport general allowed vlan add 10 switchport general allowed vlan add 11-13 tagged exit Access point is plugged into this port. The port has to be on VLAN 11 in order to get DHCP. interface ethernet 1/g16 classofservice trust ip-dscp description 'Ruckus - IT' switchport mode general switchport general pvid 11 switchport general allowed vlan add 10-12 switchport general allowed vlan add 13 tagged exit If we tag the traffic from the SSID as VLAN 11 data fails. If we leave the SSID tagged as 1 the data flows correctly. Are there problems with passing tagged traffic to untagged ports? We are looking to see what we can do to get the SSID tagged as 11 instead of 1. Any suggestions?

  Read the article

• Any way to know if two ip address points to the same machine?

  - by Vivek V K

  Is there anyway to find if two different IP address in two different network actually points to the same physical device? I need it in Linux. Edit - I have the same server(a raspberry pi) connected via 2 intranets to my client. I don't know the IP address of the server as it is DHCP. The crude way to do is to reach the raspberry pi from one intranet and check with ifconfig to find the ipadress of the machine in the other Intranet. I want to know if there is any other way I can do it? I know the mac address of the machine.But I don't know how do I find the Ipadress based on the mac address.

  Read the article

• how to broadcast a PXE server like Trinity Rescue Kit

  - by Larry G. Wapnitsky

  I would like to set up a portable PXE server for diagnostic purposes. The issue is that I won't always have access to the DHCP server, or the router itself (sometimes a home router) doesn't have an easily accessible place to set the servername/file for broadcast. I know that Trinity Rescue Kit is able to broadcast its PXE server without its own DHCP server. Can anyone point me in the direction to set this up on my own (without Trinity)? Thanks.

  Read the article

• Social network for internal company use

  - by khelll

  I'm seeking a social network app for employees in the company that can do the following: allows people to communicate within a company or across everyone on the social network (they can have access to a group or to everyone) post and archive interesting links, documents, etc. start a thread that goes to a group or to everyone lookup people’s info (profile) integrate w email so I can know if someone posts something new or responds to a questions Open source + customized deployment is a plus.

  Read the article

• I can't connect to my network, except in safe mode

  - by eidylon

  My laptop cannot connect to my network all of a sudden except in safe mode. When it boots, it will show the networks available in the tray popup, but if I click connect on any, it says "Unable to connect" and the troubleshooter is useless. Shortly thereafter all the networks disappear. I have tried removing IPv6 support as I have seen that cause problems. No joy. I've also tried removing the wireless network adapter in Device Manager and reinstalling it, also no joy. I've also tried attaching a USB wireless adapter, and it has the same problem. If I boot in safe mode, then it has no problems at all. Three other devices in the house connect fine, so I am pretty sure it is nothing to do with the router. Any ideas what to check next? I am running Win7 Ultimate on a 2GHz Quadcore with 8GB RAM with a Broadcom 802.11n wireless card. EDIT: RE wired connections: What is very weird is that if i plug in a wired connection, then not only does it connect via the wired connection, but the wireLESS also starts working perfectly. And a soon as I unplug the wire, then the wireLESS stops working again! So it seems the wireless is right now working only in safe-mode, or when a wired connection is also plugged in.

  Read the article

• Spoof user agent for GoGo Inflight Internet?

  - by AndyL

  Is it possible to trick the GoGo Inflight WiFi on airlines into thinking that you have a mobile device instead of a laptop? It seems like most airlines that offer in flight wireless these days use GoGo. They offer different pricing for mobile and laptops. It seems like they are checking the browser's user agent. Out of curiosity, is it possible to use a Firefox extension like this one to spoof the user-agent and allow a laptop to access the internet under a GoGo mobile plan? How would GoGo handle something like an IMAP email client, like Thunderbird. Do IMAP clients have a user-agent field as well that would normally identify whether the mail client is running on a laptop or mobile device?

  Read the article

• How can I view my IIS hosted sites on other machines on my network

  - by Truegilly

  Hello, at home i have a simple network setup conatining 2 machines and 1 belkin router. On one machine i have a site hosted with IIS7. Rather than the standard localhost/index.htm address i have added an entry in the HOSTS file pointing the local ip (127.0.0.1) to this domain - www.mysite.dev. i can access the site with www.mysite.dev with no problem. what i would like to do is be able to view this site from my other machine on the network. initially i assumed this could be done with a url like so MACHINE-NAME/www.mysite.dev, but the connection always times out. But I can ping MACHINE-NAME without problems. For testing purposes i have diabled the windows firewall on both machines but to no joy. Like a typical web developer, my techy/network skills are pretty poor. Can anyone see where im going wrong ?? thank you for your time Truegilly :)

  Read the article

• Does Guest WiFi on an Access Point make any sense?

  - by uos??

  I have a Belkin WiFi Router which offers a feature of a secondary Guest Access WiFi network. Of course, the idea is that the Guest network doesn't have access to the computers/devices on the main network. I also have a Comcast-issues Cable Modem/Router device with mutliple wired ports, but no WiFi-capabilities. I prefer to only run one router/DHCP/NAT instead of both the Comcast Router and the Belkin Router, so I can disable the Routing functions of the Belkin and allow the Comcast Router to But if I disable the Routing functions of the Belkin device, the Guest WiFi network is still available. Is this configuration just as secure as when the Belkin acts as a Router? I guess the question comes down to this: Do Guest WiFi's provide security by 1) only allowing requests to IPs found in-front of the device, or do they work by 2) disallowing requests to IPs on the same subnet? 1) Would mean that Guest WiFi on an access point provides no benefit 2) Would mean that the Guest WiFi functionality can work even if the device is just an access point. Or maybe something else entirely?

  Read the article

• internet service providers

  - by gautam kumar

  I am unclear about the differences between international, national, regional and local ISPs. Please explain the differences and their importance, with examples. I am new to this site, so please forgive me if my question is not up to your expectations.

  Read the article

• How are you suppose to NAT with snow leopard server mini with only 1 ethernet port?

  - by erotsppa

  How are you suppose to NAT with snow leopard server mini with only 1 ethernet port?

  Read the article

• How to fix massive lag on ZyXEL HomePlug AV powerline adapters?

  - by Tim Abell

  I have 3 ZyXEL Homeplug AV powerline adapters as per the one in the review below. I have two plugged in currently, one into my Be / Thompson wireless router, and one into my desktop pc (box1). every now and then the link indicator on the adapters (the mains link, not the ethernet link) goes nutty, and performance falls off a cliff (see below). http://www.gadgetspeak.com/gadget/article.rhtm/753/479266/ZyXEL_PowerLine_HomePlug_AV_PLA401.html 64 bytes from box1 (192.168.1.101): icmp_seq=1064 ttl=64 time=996 ms 64 bytes from box1 (192.168.1.101): icmp_seq=1065 ttl=64 time=549 ms 64 bytes from box1 (192.168.1.101): icmp_seq=1066 ttl=64 time=6.15 ms 64 bytes from box1 (192.168.1.101): icmp_seq=1067 ttl=64 time=1400 ms 64 bytes from box1 (192.168.1.101): icmp_seq=1068 ttl=64 time=812 ms 64 bytes from box1 (192.168.1.101): icmp_seq=1069 ttl=64 time=11.1 ms 64 bytes from box1 (192.168.1.101): icmp_seq=1070 ttl=64 time=1185 ms 64 bytes from box1 (192.168.1.101): icmp_seq=1071 ttl=64 time=501 ms 64 bytes from box1 (192.168.1.101): icmp_seq=1072 ttl=64 time=1975 ms 64 bytes from box1 (192.168.1.101): icmp_seq=1073 ttl=64 time=970 ms ^C --- box1 ping statistics --- 1074 packets transmitted, 394 received, +487 errors, 63% packet loss, time 1082497ms rtt min/avg/max/mdev = 5.945/598.452/3526.454/639.768 ms, pipe 4 Any idea how to diagnose/fix? I'm on linux so installing the windoze software that came with them is not something I'm terribly keen to do.

  Read the article

< Previous Page | 111 112 113 114 115 116 117 118 119 120 121 122  | Next Page >