Search Results

Search found 34971 results on 1399 pages for 'st even'.

Page 116/1399 | < Previous Page | 112 113 114 115 116 117 118 119 120 121 122 123  | Next Page >

• How would you diagnose an integrated network card that doesn't show up on the device list?

  - by Tomer Gabel

  I've been setting up a server based around a Gigabyte GA-G33M-DS2R motherboard (G33, PCH9R with integrated Realtek 811B network device. I've enabled it in the BIOS, but it doesn't show up in the pre-boot PCI device list, isn't recognized by Windows (even after installing the chipset and networking drivers) and doesn't even show up via lspci. I've tried cycling power, disabling, cycling again, enabling, cycling again etc. to no avail. I'm sort of at a loss at this point; the board isn't under warranty anymore, but I'd rather not have to replace it. Any advice would be greatly appreciated...

  Read the article

• Inexpensive degaussers or HDD shredders?

  - by Nicholas Knight

  I do a lot of work for a small cash-strapped business that has a lot of active hard drives, most are consumer-grade SATA of about five years of age, and predictably they are dying at an increasing rate, and a lot of the time they can't even be detected, let alone complete a zero-out cycle. Right now those drives are just being stored, but that can't continue forever. We've got a couple bad LTO tapes it'd be nice to deal with, too. There are very real security and legal issues that make dropping them off with someone who claims they'll be properly destroyed a gamble. I've looked around at degaussers and HDD shredders, and the ones that don't look like they come from some guy in his basement all seem to be $3000+, which is hard to swallow right now. Is there anything out there in the $500-1500 range that you would recommend? (Speed isn't a big issue, if it takes several minutes or even hours per drive, that's completely OK, we've only got 10 or so thus far.)

  Read the article

• Centos 6 - How to upgrade module located inside initramfs?

  - by anonymous-one

  We have recently upgraded our e1000e (intel ethernet) module on one of our centos 6.0 boxes. Even tho the module compile and installed fine, the old version is still being used. We have tracked this down to the fact that the e1000e.ko module is located inside the initamfs file for the booting kernel and thus, even tho the module located in /lib/modules/.... was being updated, the old one is still being loaded from inside the initramfs file. After some research, we have found that creating a new initamfs file in centos should be as simple as: /sbin/dracut <initramfs> <kernel-version> Can someone confirm that this is a safe way to basically recreate the initamfs file? This is a non-locally hosted (1000's of km away...) box, and getting support to resolve this if a reboot is unsuccessful will lead to quite a bit of down time. Thanks.

  Read the article

• Differences between FCKeditor and CKeditor?

  - by matt74tm

  Sorry, but I've not been able to locate anything (even on the official pages) informing me of the differences between the two versions. Even a query on their official forum has been unanswered for many months - http://cksource.com/forums/viewtopic.php?f=11&t=17986&start=0 The license page talks a bit about the "internal" differences http://ckeditor.com/license CKEditor Commercial License - CKSource Closed Distribution License - CDL ... This license offers a very flexible way to integrate CKEditor in your commercial application. These are the main advantages it offers over an Open Source license: * Modifications and enhancements doesn't need to be released under an Open Source license; * There is no need to distribute any Open Source license terms alongside with your product and no reference to it have to be done; * No references to CKEditor have to be done in any file distributed with your product; * The source code of CKEditor doesn’t have to be distributed alongside with your product; * You can remove any file from CKEditor when integrating it with your product.

  Read the article

• No internet on some devices, still on WiFi

  - by Joost

  Ok, here's the situation. I live with 3 friends, and we often sit in the living room with laptops out. There's a WiFi router in the kitchen, and we have quite a stable connection. The issue, however, is this: sometimes, all of a sudden one of my friends loses internet connection. Even disconnecting/reconnecting to the WiFi network does not help. When we restart the router, though, it works like a charm again. The odd thing is, it happens just for this one Windows 7 laptop. We've switched routers (for a different reason) in the mean time, but the issue remained. This makes me suspect the laptop even more. I realise I've given little details, but I don't really know what to try/do. Any suggestions what it might be?

  Read the article

• Network card dies when trying to wake up laptop from sleep

  - by Bugmaster

  I have a Dell XPS 1640 laptop (aka Dell Studio XPS 16), running Vista. Whenever the laptop wakes up from sleep, my Broadcomm LAN card immediately dies. Any attempt to access it completely locks up whichever program I use to access it. There appears to be no way to re-awaken the card, other than rebooting; note that Vista does not even shut down properly if some program is waiting for the card. So far, I have tried the following: Disabled the "allow your computer to shut down this device to save power" in the device properties. This had no effect. Attempted to disable and then enable the card in the device properties. No effect. Tried ipconfig /renew: this locks up ipconfig to the point where I can't even kill its process. Force-install updated drivers from broadcomm: no effect. Does anyone have any other ideas ?

  Read the article

• Laptop gets really hot then turns off, suspect it is overheating. How can I reduce this?

  - by nixnub

  My laptop keeps overheating and turning itself off. Underneath it gets really hot. Even playing 3D online poker is impossible, it just overheats. If it is on my lap, I try and balance it so it's sitting just on my legs and has loads of free space under it. This seems to help a bit (it's never turned itself off in this position) but even being on a desk can result in it overheating. There is a lot of dust, etc that I've cleaned it out (as much as I can easily take apart anyway), but it never used to happen. Any ideas? The laptop is a Lenovo 3000 N200.

  Read the article

• Why does my webpage look different when I connect using different routers?! Does routers cache files?

  - by Ayyash

  Here is the case, I am working on a site from office and home, I recently updated the stylesheets and logged in the live site from office (using my same laptop I use all the time), and everything looks okay, I come home use my home internet connection to connect to the site using the SAME laptop, the styles are not updated! The thing is: this happens on ALL browsers, and after emptying the cache many times, and even after one month of work, and even if I have never opened the site before on that browser (as if my router has a cache of its own) Another thing: only one particular styles.css file seem to be hanging Extra info: I use the same IP for my home wireless router as that defined in the office, the usual 192.168.0.1

  Read the article

• How do I use XQuartz with ssh on OS X?

  - by cwd

  I've downloaded the latest stable version of XQuartz on my Snow Leopard machine, and I'm trying to make an ssh connection with X forwarding but X11 keeps opening. How can I get OS X to use XQuartz? I had X11 installed I downloaded and installed XQuartz X11 is not open / running XQuartz is open and running I try and connect to a remote system using iTerm2: ssh user@remote -X X11 opens. XQuartz is still open, but I doubt it is doing anything. I also tried moving X11 to the trash but then the ssh connection will not complete, even though XQuartz is open. I also get the two warnings which I don't understand how to fix, even after reading the ssh man page. Warning: untrusted X11 forwarding setup failed: xauth key data not generated Warning: No xauth data; using fake authentication data for X11 forwarding.

  Read the article

• PHP fopen fails - does not have permission to open file in write mode.

  - by George

  Hello. I have an Apache 2.17 server running on a Fedora 13. I want to be able to create a file in a directory. I cannot do that. Whenever I try to open a file with php for writing fopen(,'w'), it tells me that I don't have permission to do that. So i checked the httpd.conf file in /etc/httpd/conf/. It says user apache, group apache. So I changed ownership (chown -R apache:apache .*) of my whole /www directory to apache:apache. I also run chmod -R 777 * Apart from knowing how terribly dangerous this is, it actually still gives me the same error, even though I even allow public write!

  Read the article

• Can anyone recommend an iPhone dock with PC pass through? [closed]

  - by Kelsey

  I am looking for a dock for my iPhone that has external speakers, a PC pass through, ability to dock vertical and horizontal and accomodate my iPhone case (Oakley case). The case I use is a problem with most docs but if there was one with an extendable connector it would be fine. I really haven't found any docs that work well with any cases. PC pass through doesn't seem very common at all. I don't want to have a seperate cable for my synching and a dock for my desk. Any recommendations even if they are not released yet? Maybe even alternatives to a dock?

  Read the article

• Wrong chrome full screen resolution with multiple displays

  - by Martin

  I am using Google Chrome on Windows 7 64bit with two displays. The displays have different resolutions and aspect-ratios. My problem is best visible when playing back full-screen videos from a flash player inside chrome (but it is not flash related). The maximum size is calculated from the primary displays' resolution, even when the relevant window is maximised on the second screen. The problem is also visible on websites that set the width to 100%. The 100% then apply to the primary display, even when the window is opened on the secondary display. Are there any known solutions to this problem? I am observing it since many Chrome versions, do not know if it has been ever correct.

  Read the article

• ShoreTel 230 phone calls from website

  - by Michael Irey

  Our company uses these fancy ShoreTel 230 phones. We make many phone calls from our custom built web based contact management system. It would be nice if our employees could click on a phone number from a webpage and have it automatically start dialing the number. (Similar to how iPhone handles this) Anyone every deploy something like this? I would imagine it would require some kind of background running ShoreTel process to accommodate this. 90% of our employees use PC (Windows 7) 10% use OS X Even a PC only solution would be great. Is this even possible and if so, where should one begin? Thanks!

  Read the article

• vim on Windows -Turn syntax highlighting OFF

  - by sandro

  I have downloaded Vim 7.4 on Windows 7 64 bit, and would like to turn off syntax highlighting. I have been using Vim for a long time on Unix, so I know to place "syntax off" in my vimrc. However, even though "syntax off" is in my vimrc, for some reason when I edit my vimrc the syntax highlighting is always on. I have deleted every other vimrc on my system (listed in the output of :version) except for my $HOME\_vimrc, but the syntax highlighting is still there (even after creating new cmd's). Any help would be greatly appreciated.

  Read the article

• windows 7 is not working with Ubuntu 12.04

  - by Anand Soni

  I have one problem, I am unable to start windows 7 which is installed with Ubuntu 12.04 because I want to utilize all resource in diff. OS. Let me tell you the installation I have done. I have installed everything with USB because my CD ROM is damaged. 1) I have installed Windows 7 in c: then I have installed Ubuntu 12.04 in C: Now when I start my PC it shows list of OS first like -Ubuntu 12.04 -Windows 7 When I click on Windows 7 it do not starts and again shows the list of OS. I have also tried to reinstall the windows 7 using USB but it gives error of something UI or Boot configuration error. Even now Ubuntu 12.04 is also not reinstalling. Now what I want to do is install windows 7 and install ubuntu 12.04 in virtual box so that I can run both system as this is not working. But can't because I can't open Window 7 even can't format my drive. Please suggest something.

  Read the article

• Transport rule - Exchange 2010

  - by Jeff

  I have two transport rules on my exchange server. One is: > Apply rule to messages: From users that are 'outside the organization' > and when any of the recipients in the To or Cc fields is a member of > '[email protected]' Forward the messageto sender's manager > for moderation The second is: Apply rule to messages from a member of '[email protected]' and sent to users that are 'outside the organization' forward the message to the sender's manager for moderation. nointernetmail is a distribution group, and each user has the managed by set to there local manager. However these transport rules do not work, internet mail is still sent and received without issue. I have read various tutorials / articles of how to do this on sites such as msexchangeblog and even microsoft technet, however even after following the guides I am still unable to have this function properly. Any help is appreciated.

  Read the article

• Why does Windows 7 x64 work faster than an x86 edition on my PC?

  - by Jasper

  Why does Windows 7 x64 work faster than an x86 edition on my PC even though I mostly use x86 things in it? What's wrong with me, and what am I missing? Majority of the things I use is x86 (e.g. DAWs, games, media players). A considerable amount of them, however, are x64 (although their x86 counterparts work just fine). I've tried using the same things on the same system but always ended up finding Windows 7 x64 working slightly faster than x86. I'm very observant. I even notice the tiniest window animations. System: Windows 7 Ultimate x64 CPU: Intel Core 2 Duo E7500 @ 2.93 GHz RAM: 2 GB x 2 = 4 GB DDR2 @ 332 MHz Motherboard: Intel D945GCNL Graphics: ATI Radeon HD 4350 @ 1 GB Dedicated Audio: M-Audio FastTrack Pro HDD: Samsung HD753LJ 733 GB & Samsung HD160JJ 156 GB As you can see, my system is old.

  Read the article

• when connected to vpn, can't access certain things

  - by shsteimer

  my companies vpn is not a standard windows vpn. It uses Juniper Networks and it intalls locally something called "Host Checker" prior to allowing me to connect. I have noticed 2 things that I can't access while on vpn. etrade.com - no idea why this specific website, but I can't get to it, maybe https? use of my magik jack - I'm assuming this is some sort of a port conflict issue. if im on a call when i connect, i lose all reception. if i try to make a call after conected, ic an't even get it to dial. Can anyone tell me how I would even begin to debug this. I expect if I call the help desk they won't be much help, but if I can tell them the specific problems of conflicts, maybe I have a chance of them working with me to get it working.

  Read the article

• Unable to set .NET 4 on Application Pool from remote, works locally on server

  - by Robin Wassén-Andersson

  I have setup Remote Administration for IIS successfully and connected to it. For some reason .NET Framework 4 doesn't show up as an option when configuring the Application Pools from remote even though .NET 4 is installed on both server and client (not that client should matter). If I login to the server with RDP and configure the Application Pools it work as intended, the option shows up. Even more odd is if I edit an Application Pool that already runs .Net 4 it shows up as an alternative (kind of strangly formatted text though, just says v4.0 instead of .NET Framework v4.0.30319 ) How should I proceed to solve this?

  Read the article

• Why Photoshop CS5's photomerge's result immediately disappear?

  - by koiyu

  I have a bunch of JPG-files which I want to stitch together with Photoshop's Photomerge function. I choose File → Automate → Photomerge... and browse for the files. Photoshop opens the files and starts analyzing. I see the process bar filling and different phases are mentioned on the process bar. Nothing weird there. When the merging is done (and if I don't blink my eyes), I can see layers-palette is populated with the chosen files and, by quickly judging from the layer thumbnails, they're properly aligned. Sometimes the image window itself can be seen, but not always. Problem is that the layers and the image disappear in a flash. There is no error message. Everything is like prior starting the photomerge. No file has been changed. I could continue to use Photoshop normally. This is what I've tried so far: Loaded folder which has 38 JPG images, 4272 x 2848 and ˜ 5 megabytes per file Loaded the same files, but chose Use Files instead of Use Folder in the photomerge's window Loaded 19 JPG images, 4272 x 2848 and ˜ 5 megabytes per file Loaded 10 JPG images, ⇑ see above Loaded 5 JPG images, see above Loaded 3 JPG images, see above Scaled the images to 2256 x 1504 and ˜< 1 megabytes per file Loaded in a set of 38, 19, 10, 5, 3 Following steps are tested with these smaller files and with a set of 5 images Read Adobe's forums and reduced the amount of RAM Photoshop uses gradually from ˜ 80 % to 50 % (though I didn't understand the logic behind this) Would've reduced cache tile size to 128K, but it was set so already Disabled OpenGL Scaled the images to 800 x 533 and ˜ 100 kilobytes per file, loaded a set of 5 Read more unanswered threads around the internet In between each test I closed and reopened Photoshop. This is the first time I've even tried using photomerge. Am I doing something wrong? How can I locate what is the problem? How do I fix this? Photoshop is 64 bit Extended CS5 version. I'm on a mid-2010 quad-core (i5) iMac with up-to-date Mac OS X 10.6.6. Edit: Weird. First loading the images into one file via File → Scripts → Load Files into Stack… and then using Edit → Auto-Align Layers…, which, effectively, is the same as photomerge (even the dialog looks kind of the same), works! Even with the original JPGs without any issues. This doesn't fix photomerge, though.

  Read the article

• SAN/NAS with high availability?

  - by netvope

  I have two servers that I plan to use for storage. Each of them has a few SATA disks directly attached. I want the storage to be available even if one of the storage servers is down (preferably the clients wouldn't even notice that the fail-over, although I'm not sure if this is possible). The clients may access the storage via NFS and samba, but this is not a must; I could use something else if needed. I found this guide, Installing and Configuring Openfiler with DRBD and Heartbeat, which apparently does the thing I want. It relies on three components, Openfiler, DRBD, and Heartbeat, and all three of them need to be configured separately. I'm wondering are there simpler solutions? Is using DRBD+Heartbeat the best practice for a situation like mine? I'm also interested to know if there are alternatives that don't depend on DRBD.

  Read the article

• Point subdirectory to another domain is IIS 6

  - by Liviu

  Is it possible to rewrite somehow www.mysite.com/Pictures to point to test.mysite.com/Pictures or even more broadly www.someothersite.com/Pictures ? Note: www.mysite.com and test.mysite.com are on separate machines and built with different technologies (one is ASP.NET and the other is PHP) but I have access to both of them. I want that when I reference a picture like www.mysite.com/Pictures/pic12345.png the picture to display correctly, even though there is not /Pictures folder on that server and the pictures has to be retrieved by going to test.mysite.com/Picture/pic12345.png Ideally I want to do this in IIS6 to test it. However I am interested if it possible to do in any webserver (Apache, IIS7)

  Read the article

• how to make SFTP work on Windows

  - by cyberkiwi

  What is the correct way to set up sshwindows for SSH key authentication? Does the user need to be created in Windows first or can a login be inserted into passwd without a Windows equivalent? I've searched on Google and have tried the tutorials and quick start guides. So far, exactly 0 have worked. None pointed out that to work in Windows 2008 R2, you need to change the properties of cygrunsrv.exe to "Windows XP SP3" compability mode to even get past the service startup "error 1067". Although it is running, no amount of configuration allowed me to log on to the SFTP server, even though I tried (from another machine): same user account added using "mkpasswd" + windows password same user account added using "mkpasswd" + public ssh key (added to /home/theuser/.ssh) On Windows 2003 R2 (a different attempt), the service would crash every time it started up. Some links I went through http://pigtail.net/LRP/printsrv/cygwin-sshd.html http://forevergeeks.com/how-to-setup-a-secure-ftp-sftp-site-with-openssh-on-windows/ http://support.moonpoint.com/os/windows/server2003/openssh-service-not-starting.html

  Read the article

• HTTPS vs. VPN for communication between business partners?

  - by Andrew H

  A business partner has asked to set up a site-to-site VPN just so that a few servers can communicate with each other over HTTPS. I'm convinced this isn't necessary, or even desirable. To be fair it must be part of a wider policy, potentially even a legal requirement. However I'd like to convince them to simply offer an IP to us (and us only) and a port of their choosing for HTTPS. Has anyone had a similar experience, or had to come up with a cast-iron argument against a VPN? Allow me to expand a little - we have a web service that initiates a connection to the partner's corresponding service using an encrypted HTTP connection. The connection uses a client certificate to authenticate. The connection is firewalled so only our IPs can contact the service. So why is a VPN necessary?

  Read the article

• Replace gvimext.dll in Windows 8

  - by Leftium

  How can I get the "Edit with ... using tabs" functionality in gVim on Windows 8 (64-bit)? I'd like to swap out gVim's stock gvimext.dll for one that adds an "Edit with ... using tabs" option to Explorer's right-click context menu. On Windows 7 (64-bit) I used to be able to download the DLL and swap it in by following these instructions. However, I can't get it to work in Windows 8. The stock installation's context menu (sans "... using tabs") works fine (without a restart) ...but after replacing the DLL the gVim context menu options disappear and the gvimext.dll no longer seems to even load. (Windows 8 was restarted) if I again replace gvimext.dll with a backup of the stock DLL, the context menu options remain missing and the DLL still seems to fail to load (Windows 8 was restarted, again) If I re-install gVim, the context menu items return (even without a restart) What is the difference here between Windows 7 (where swapping DLL's works) and Windows 8 (where swapping DLL's fails)?

  Read the article

< Previous Page | 112 113 114 115 116 117 118 119 120 121 122 123  | Next Page >