Search Results

Search found 9758 results on 391 pages for 'wireless networking'.

Page 117/391 | < Previous Page | 113 114 115 116 117 118 119 120 121 122 123 124  | Next Page >

• Wifi speed with driver rtl8187 drops

  - by Peter

  I am using lucid lynx with this USB adapter and drivers rtl8187. When I start a download, it starts at 1500kpbs (if i use "iwconfig wlan0 rate [more than 11MB]" it starts at a lower speed), it transfers a few kbs but then the speed starts to drop constantly and nothing is being transferred. I've also tried the driver r8187, but I have the same speed problem only that with this driver the download starts at only 10kbps, and drops from there. What can I try to identify the cause and fix this problem?

  Read the article

• ACER ASPIRE ONE, WIFI Atheros Communications Inc. AR9462 problem with 12.10

  - by antoine

  I have an ACER ASPIRE ONE AO756-Series, equipped with A wifi controller Atheros Communications Inc. AR9462 Everything worked fine on 12.04, but when I upgraded to 12.10 I experimented some issues : * wifi does work ! * still, the wifi icon/menu does not react normally : 1) it is always grey, hence not indicating if connected or not, 2) It does not react to me clicking on it (disconnect, change the network, desactive wifi, etc) So it's not a critical issue because I can change the active wifi connection through control pannel, but it is very annoying. Do you know of an solution around this issue ? thanks a lot antoine

  Read the article

• Setting primary internet connection and network on notebook

  - by Francois

  I have installed Ubuntu on a notebook that I have configured to connect to the internet using an Iburst USB modem. This works 100% after a bit of configuring. I now have a desktop pc that I have installed ubuntu on, and would like to connect the two with a router. I bought a router with wifi, and would like to connect my notebook to the other computer using wifi, while still keeping the internet working with the usb modem. The problem is that as soon as the wifi connect, the internet connection dies. Is there a way to force ubuntu to get internet access through the usb modem, but use wifi to connect to the network? I am pretty new to ubuntu so any help would be appreciated. I also have a samsung galaxy tab that I would like to connect to the internet through usb modem via the wifi, so is there also a way to share that internet connection with the other computers on the network? Thanks in advance.....

  Read the article

• rt73.bin for Ubuntu 12.04 LTS?

  - by fNek

  I have a D-Link USB WLAN stick and want to install Ubuntu 12.04 alternate. The installer asks me to insert an exchangable drive containing 'rt73.bin', the driver. I cannot find any binary downloads, but cannot build the package, because I have no other linux PC. What can I do? //EDIT: The reason why I want to do this during setup is that I want to setup an LTSP server. I only found guides that assume one has Internet connection - but I have not. What can I do?

  Read the article

• Layman's book for understanding computer networks

  - by srid

  The good thing about books targeting a layman is that it is usually very engaging to read (not dry and boring like, say, school/university books). Charles Petzold's Code: The Hidden Language of Computer Hardware and Software does this for explaining the underlying hardware in computers. Is there a similar book for understanding computer networking?

  Read the article

• Best way to provide redundant switching/links to server

  - by Myles Gray

  We have 3x ESX hosts and 2x SANS that we wish to move to a redundant 10G networking infrastructure. We have 4x Dell PowerConnect 8024F's to provide our backbone and are configured as so (only core switches relevant to this question): So the questions are: 1) Do the interconnects between the 4x 8024F's need to be LAG'd or just STP'd 2) As the NICs on the servers are split across 2 switches, does any special configuration need to be done here or on the switches? 3) If a link or switch fails will the switches automatically find a new path to the Server/SAN?

  Read the article

• Ubuntu on Thinkpad Edge 11/13/14/15

  - by lasseespeholt

  I think a community wiki on problems (and solutions) when installing Ubuntu (10.10) on a Thinkpad Edge 11 would be nice (because I just got one ;)). I'll contribute with my own problems and solutions, and hope others will join too. Thinkwiki entry for the Edge 11 Known problems: No wifi-driver, solution: answer #1, answer #2 Fan is loud, even though it's on auto. No solution. Thinkfan is a possible solution, but correction values for sensors should be supplied (mapping sensors to specific areas). Also, one sensor is between -100C and +100C - maybe some kind of deactivation would help. FN keys stop working: see below. No sound on headphones: see below.

  Read the article

• How can I manage all my social network accounts from a single source?

  - by Peter Di Cecco

  Hi all, Like many people, I have accounts on facebook, twitter, tumblr and this and that... I'm looking for the ultimate solution for combining social networking sites. Something like Ping.fm. Update in one place and the others get updated automatically. Is Ping.fm the only solution? How do you update your various social sites? How do you keep updated? Thanks.

  Read the article

• Ubuntu and Surface Pro, wifi issues not fixed?

  - by Confused or too stupid

  Just a quick question, from the numerous other threads I found, is the wifi still a no go straight out of installing Ubuntu? I tried this Dual boot Surface Pro with Ubuntu? with 13.04, the wifi is sporadic in working. From that and other threads I gathered that 13.10 would include the fix, so I tossed that onto the Surface as well, with the same results. Is there anything I am missing? Is there any other distro that has better luck with the Marvell chip?

  Read the article

• Connection manager detects network but won't connect

  - by Carson Chittom

  I've just installed 12.04 on my home desktop. Because of where it's located, in order not to have my children tripping over cat5 cable, I've got a cheap 802.11n USB device plugged in, which uses a Realtek 8192CU chip. The house wifi is protected with WPA2. Ubuntu's Network Manager detects the network, but connecting to it just times out and asks for the password again. I'm sure I'm using the correct password. No other computers on the house network are having any difficulty. This device previously worked correctly with both Windows 7 and OpenBSD in the same machine. The linux-firmware package is installed (from the disc) at version 1.79, and /lib/firmware/rtlwifi/rtl8192cufw.bin is present. dmesg|grep rtl only shows the "loading firmware" message. I've tried Google, but I apparently can't find the right set of words to plug in, because I haven't found anything related (lots of "doesn't work at all," but nothing matching my circumstances). Any help would be greatly appreciated.

  Read the article

• Wlan connection got lost permanent

  - by chris

  I have a desktop with a fritz usb wlan n tick and tried ubuntu 12.04. installlation is fine and wlan is working, however connection drops permanent. reconnecting manually fixes it but after a few minutes it drops again. it's connected to a vodafone 802 box with wlan n fix set. it seems that it works when i switch off n mode...but i need to test. can someone confirm or is there another solution? i have another machine with 12.04 (hp 625 laptop) running where connection is stable. any help much appreciated. thank chris

  Read the article

• USB Wifi that works with 12.04

  - by Colin Matheson

  I have done several hours of searching and I am still looking for a few USB wifi adaptors that run in 12.04 with no additional driver installations or other fiddling. I am looking to plug in the adaptor and have the laptop recognize and start connecting. We have 30 older laptops with flaky internal wifi cards so I thought that if I could find a $10-$20 USB adaptor that work reliably in 12.04 I could plug it in and solve all my connectivity problems for a few hundred dollars.

  Read the article

• Missing driver ASUS PCE-N53 11n N600 PCI-E Adapter

  - by oyse

  I have problems with getting an Asus PCE-N53 11n N600 PCI-E Adapter card to work on my desktop computer. As far as I can tell no drivers are installed for the card. I know I can manually download the drivers directly from Asus, but I would rather not go that route. If there are anyone that knows about any packages or other things I can do to make this work would be much appreciated. Some systems details: $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04.1 LTS Release: 12.04 Codename: precise $ sudo lshw -C network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: d4:3d:7e:03:b9:1d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=192.168.0.173 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:d000(size=256) memory:f2104000-f2104fff memory:f2100000-f2103fff *-network UNCLAIMED description: Network controller product: Ralink corp. vendor: Ralink corp. physical id: 0 bus info: pci@0000:04:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7100000-f710ffff $ lsmod Module Size Used by nvidia 12319264 51 vesafb 13844 1 snd_hda_codec_hdmi 32474 1 joydev 17693 0 bnep 18281 2 rfcomm 47604 0 bluetooth 180104 10 bnep,rfcomm snd_hda_codec_realtek 224173 1 snd_seq_midi 13324 0 ppdev 17113 0 snd_rawmidi 30748 1 snd_seq_midi usbhid 47199 0 hid 99559 1 usbhid nouveau 774641 0 parport_pc 32866 1 snd_hda_intel 33773 5 ttm 76949 1 nouveau snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel drm_kms_helper 46978 1 nouveau drm 242038 3 nouveau,ttm,drm_kms_helper snd_seq_midi_event 14899 1 snd_seq_midi snd_hwdep 13668 1 snd_hda_codec snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event i2c_algo_bit 13423 1 nouveau mxm_wmi 12979 1 nouveau wmi 19256 1 mxm_wmi mac_hid 13253 0 snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec psmouse 97362 0 video 19596 1 nouveau snd_timer 29990 2 snd_seq,snd_pcm snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 20 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_rawmidi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_seq,snd_pcm,snd_timer,snd_seq_device serio_raw 13211 0 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp r8169 62099 0

  Read the article

• Configuration of the network manager via DBus: how to set the ad hoc mode

  - by Andrea

  I have an hard nut to crack: a nice bottle of italian Chianti wine to the solver! :) To automatically configure Wifi, I first have to kill the network manager and than activate the wifi via the commandline: I do this all automatically in my application and works great. However... it is not the right way to do this. As the user has no network gui anymore to configure some other network access. A much better and transparent way would be to configure wifi directly via network manager over the DBus interface. I was able to configure it, but I wasn't able to set it to ad hoc mode... Searching the web for a while: a lot about configuration in general but nothing related to ad hoc mode. I think the only way to do figure that out is to look into the source code of the network manager...maybe someone already did it and he can answer.

  Read the article

• How to completely remove wicd from 12.04?

  - by danijelc

  I had issues with WiFi so I removed Network Manager. I booted Windows OS (dual booting Windows 7 and 12.04) to download wicd 1.7.2.4. Extracted it and installed. However, wcid worked properly with Wired Connection but could not connect to WiFi. So, I re-installed Network Manager which works properly now, and wicd connects to WiFi too. As soon as I disconnect from Network Manager, wicd connects only to wired. At this point, I wanted to remove wicd but apt-get returns no wicd installed, can't see it in Synaptic or Software Center, but only in Applications list under Dash home. Of course wcid icon shows connections, and resulting connected, so my system shows both applets for wicd and network manager in the top panel. When running dpkg commands, wicd is not listed as installed package. Any suggestion how to remove wicd? Consider that I started with Ubuntu just few months ago so my knowledge base is limited.

  Read the article

• Not able to connect to local network

  - by Roopesh

  I have installed Kubuntu , I am able to connect to Internet and able to access external sites, but in my local network i have bugzila installed that i am not able to access, even i am not able to ping the gateway also 192.168.1.1 . below is the result of ifconfig command Please help . Thanks ~# ifconfig eth0 Link encap:Ethernet HWaddr b8:70:f4:da:f9:a8 inet addr:192.168.1.100 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:42 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:884 errors:0 dropped:0 overruns:0 frame:0 TX packets:884 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:81131 (81.1 KB) TX bytes:81131 (81.1 KB) wlan0 Link encap:Ethernet HWaddr 68:5d:43:2e:1c:79 inet addr:192.168.1.26 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::6a5d:43ff:fe2e:1c79/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2446 errors:0 dropped:0 overruns:0 frame:0 TX packets:2324 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1909441 (1.9 MB) TX bytes:393292 (393.2 KB)

  Read the article

• iwconfig usage for WEP access point?

  - by johan elmander

  I would like to use my wifi doggle in my pc (ubuntu 12.04). I am able to connect to my access point through the GUI. I would like to do the same in the terminal. My access point uses WEP. So I typed the following commands iwconfig wlan0 mode managed key 6d6f6e6579 iwconfig wlan0 essid "AccessPoint" dhclient wlan0 after typing dhclient wlan0 it waits like 1-2 min then outputs nothing and cannot connect to the Access Point. iwconfig output: wlan0 IEEE 802.11bgn ESSID:"AccessPoint" Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long timit:7 RTS thr=2347 B Fragment thr:off Encryption key:6D6F-6E65-79 Power Management:off I would appreciate any suggestion

  Read the article

• First time using Ubuntu, need help with drivers!

  - by Nick

  I have just successfully built my first computer last night. I went through the boot menu and got Ubuntu 12.10 installed properly and everything. My question is...now what? There has to be some sort of drivers I need to install right? I can't connect to wi-fi or anything of that sort. I have an ASUS motherboard, model number M4N98TD EVO , and an NVIDIA Geforce GTX 650 grpahics card. I guess my main question is, can someone run me through step by step what I need to do after I install Ubuntu?

  Read the article

• ACER Aspire V5-171 compatibility

  - by JamerTheProgrammer

  Im thinking about buying a V5-171 with an i3 in it. Im worried about secure boot though. I heard some people cant turn it off and it wont work... Im not shy to open it up and replace the hard drive with Ubuntu preinstalled. Im also worried about the wifi working. I have heard its been dropping out for people quite a bit along with also the trackpad not working. I dont mind replacing the wifi stick (if its even possible?) inside. Is the GPU (HD4000 i think) supported in ubuntu with full video accel? Thanks!

  Read the article

• Ubuntu 12.04 share the internet over WiFi from wvdial?

  - by Sour Lemon

  I have just installed Ubuntu 12.04 on a separate partition on my hard drive so I can dual boot to either Windows 7 or Ubuntu. I am living in Japan and so I'm using a mobile broadband USB device called "Softbank C02LC". By default it seems that this device isn't recognised so I did the following: Terminal: sudo su nano /usr/bin/usbModemScript Nano: #!/bin/bash echo 1c9e 9900 > /sys/bus/usb-serial/drivers/option1/new_id Terminal: chmod +x /usr/bin/usbModemScript nano /etc/udev/rules.d/option.rules Nano: ATTRS{idVendor}=="1c9e", ATTRS{idProduct}=="9900", RUN+="/usr/bin/usbModemScript" ATTRS{idVendor}=="1c9e", ATTRS{idProduct}=="9900", RUN+="/sbin/modprobe option" which made the device visible from the network manager etc. However even though I set up my details correctly when I created a new connection (Correct username, APN etc) as soon as I try to connect it almost immediately disconnects. Because of this I then followed the instructions at this site: http://debugitos.main.jp/index.php?Ubuntu%2F%A5%E2%A5%D0%A5%A4%A5%EB%A5%A4%A5%F3%A5%BF%A1%BC%A5%CD%A5%C3%A5%C8 And I ended up using the c02lc_connect script at the bottom of the page to connect to the internet. The file contains the following bash script: #!/bin/sh usbinterfece=/dev/ttyUSB2 VID=1c9e PID=9900 WRONG_PID=f000 LSUSB=/usr/sbin/lsusb GREP=/bin/grep MODPROBE=/sbin/modprobe SWITCH=/usr/sbin/usb_modeswitch SWITCH_D=/etc/usb_modeswitch.d WVDIAL=/usr/bin/wvdial SLEEP=/bin/sleep SUDO=/usr/bin/sudo WHICH=/usr/bin/which switch_config="$SWITCH_D/$VID:$WRONG_PID" if ! [ -x $WVDIAL -a -x $SWITCH ]; then echo "Install wvdial and usb_modeswitch." exit 0 fi check_usb() { local vid="$1" local pid="$2" ($LSUSB | $GREP "$vid:$pid") } if ! (check_usb "$VID" "$PID"); then echo "Cannot find modem device..." if (check_usb "$VID" "$WRONG_PID") && ( [ -f "$switch_config" ] ); then echo "The device is attached but its mode is wrong." echo "Try usb_modeswitch..." $SUDO $SWITCH -c "$switch_config" $SLEEP 1 if (check_usb "$VID" "$PID"); then echo "Successfully switched the mode." else echo "Failed to switch the mode..." exit 1 fi else exit 1 fi fi if [ ! -c "$usbinterface" ]; then $SUDO $MODPROBE usbserial vendor=0x$VID product=0x$PID $SLEEP 2 fi $SUDO $WVDIAL which works completely fine - no problems what-so-ever. But we also have 1 more laptop here which I need to share the internet connection with. In Windows 7 I do this with the Connectify program, and in Ubuntu I have seen that you can do things like set up hotspots etc. But because I am using WvDial I am not sure how I would share the internet. I am only beginning to use Ubuntu but unfortunately until I can figure out how to share the internet over WiFi when connected via WvDial I have to stick with Windows. If you have any ideas on how to do this it would be much appreciated!

  Read the article

• Which service should I make mine dependant on ?

  - by Retrocoder

  I want to add a dependency to my service so that it only tries to start after most of the Windows services have started. Can anyone recommend such a service that is unlikely to have been disabled for security reasons on corporate sites. As my service needs the networking services up and running I want to make sure mine starts after these. This service may also be deployed in non-corporate environments so I’m looking for a suitable service that is unlikely to have been disabled by the end user.

  Read the article

• how to install a 3g dongle onn ubuntu

  - by user211208

  i have a 3g dongle of lava and i am not able to install it on my Ubuntu OS.when i plug it in it does not even recognize it,although the dongle has installation setup for Linux also. so how do i use internet on Ubuntu using a 3g dongle?? i even tried out the 3g dongle of Tata Docomo.i need to get software for my P.C to listen songs and watch movies.without net the OS is useless. i clicked on the network icon on the right corner and then on VPN connections to set up and Mobile broadband connection by providing the necessary info.at the end of all the stuff i entered the password for allowing it to install but there was an error. what am i supposed to do ??

  Read the article

• How to Configure Source NAT (Private IP => Public IP Outbound)

  - by DavidScherer

  I'm running VMWare ESXi Free and have Zentyal SBS 3.2 running as a Gateway. I have 5 Public IPS (CIDR/29, let's call them 69.1.1.1 - 69.1.1.5) and currently Zentyal is bound to 69.1.1.1 as the Gateway, with the other 4 Public IPs set as Virtual Interfaces in Zentyal (wan2-wan5) I have machines sitting on the Private Network (10.34.251.x) that, when going Outbound (to Google for instance) should be seen by the Internet as an IP other than the Gateway (69.1.1.1), this is because our machines need to be able to communicate with 3rd party APIs that expect these requests to come from a specific IP. From what I could find, SNAT (Source NAT) in Zentyal is used to achieve this, but I'm not sure how to configure it and cannot find a specific piece of Documentation for it at Zentyal. I've tried setting this up a couple different ways, with no results and at this point I have no idea if I'm going about this completely wrong, or my lack of experience with networking and the associated terminology is preventing me from placing the correct values in the correct fields. I get the following form to set up "SNAT" rules in Zentyal: Perhaps someone can offer some guidance and definitions for the fields above? SNAT Address Is this the Public IP I want to masquerade? Outgoing Interface Should this by my External NIC (one connected to Public 'Net), or is it the "Private" interface? It sounds as though this should be the External interface as I want the traffic from the internal network sent Out over this Interface (using a different IP than normal, anyway) Source Is the the Source on the internal network (one of the private IPs?), a public IP I want to masquerade as, or something else entirely? Destination Is this a place on the Internet (eg, "Only do this for the Site Google.com"/IP) or am I allowing myself to become confused again? Service I'm assuming this allows me to restrict which services this rule will apply to, but is it for a service on the internal network or a service being accessed on the external network? If I can offer any further details or information to make what I'm trying to do more clear, I will happily do so. Honestly any kind of help here would be very appreciated. I'm not a NetOps or anything even close, I spend most of my day writing code and my entire "team" at this company consists of "me, myself, and I" so while I try to broaden my KB at every possible opportunity, I can only learn so much, so fast and I feel like with networking especially there's just so much, coupled with a learning curve for each solution that likes to (from my limited perspective) use slightly different terminology that what I'm used to (and I don't exactly have the necessary experience to cross reference this stuff with the stuff I already know in context).

  Read the article

• RTL8192SU-based Wi-Fi adapter disconnects permanently

  - by leventov

  I've already tried all possible (http://ubuntuforums.org/showpost.php?p=10129571&postcount=43) solutions, no progress. I'm in despair. In Windows (on the same machine) this adapter works stably. Device: Trendnet TEW-649UB. System details: Ubuntu 11.10; leventov@leventov-ubuntu:~$ uname -a Linux leventov-ubuntu 3.0.0-12-generic #20-Ubuntu SMP Fri Oct 7 14:56:25 UTC 2011 x86_64 x86_64 x86_64 GNU/Linux leventov@leventov-ubuntu:~$ lsusb ... Bus 002 Device 002: ID 0bda:8172 Realtek Semiconductor Corp. RTL8191S WLAN Adapter ... leventov@leventov-ubuntu:~$ dmesg | grep 8712 #current driver [ 8.146510] r8712u: module is from the staging directory, the quality is unknown, you have been warned. [ 8.147113] r8712u: DriverVersion: v7_0.20100831 [ 8.147124] r8712u: register rtl8712_netdev_ops to netdev_ops [ 8.147127] r8712u: USB_SPEED_HIGH with 4 endpoints [ 8.147478] r8712u: Boot from EFUSE: Autoload OK [ 8.551272] r8712u: CustomerID = 0x0000 [ 8.551275] r8712u: MAC Address from efuse = 00:14:d1:6c:52:19 [ 8.551625] usbcore: registered new interface driver r8712u [ 9.501351] r8712u: Loading firmware from "rtlwifi/rtl8712u.bin" [ 10.160471] r8712u: 1 RCR=0x153f00e [ 10.161241] r8712u: 2 RCR=0x553f00e leventov@leventov-ubuntu:~$ lsmod | grep 8712 r8712u 189049 0 t

  Read the article

• How Windows Server routes PTP v2 unicast messages?

  - by Bobb

  If my server is placed in PTP v2 enabled network which has grand master clock. And the switch is PTP aware. The server is W2008R2 (soon to be W2012). I also have PTP v2 software client. How does the master clock messages are getting on with Windows Server? Does it need special PTP-aware NIC or it will be treated as normal networking traffic and the software receives it through regular NIC no problem?

  Read the article

< Previous Page | 113 114 115 116 117 118 119 120 121 122 123 124  | Next Page >