Search Results

Search found 3617 results on 145 pages for 'physical wear'.

Page 118/145 | < Previous Page | 114 115 116 117 118 119 120 121 122 123 124 125  | Next Page >

• Microsoft Deployment Toolkit 2012 Error

  - by Jacob Schaer

  I just started with MDT2012 recently in hopes of eventually getting away with using Ghost to deploy all of our department computers. When I test deploy in VirtualBox, it deploys the OS properly, but stops because of a network driver failure (it gets the "could not allocate resources" issue). On physical hardware (Latitude E6500, Optiplex 980, and an older Latitude) it gets through the multicast and stops immediately after with: "Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information" I've looked at the logs and never see anything really of note. Originally I was using DriverPacks from DriverPacks.net, but thinking it was a driver issue, I switched over to using Dell's cab driver packs. Still the same issue. I check and it did the HDD is all fine - it was properly partitioned, set to bootable, and was loaded with all the proper OS installer files. I'm using a flash drive to do the install - when I make changes to the deployment share I rebuild and copy the ISO to the drive, then use YUMI multiboot to start the ISO (probably irrelevant).

  Read the article

• How to tell Linux to explicitly swap out main memory of a suspended process?

  - by Vi

  I run a memory-hungry process (mkcromfs) which consumes more memory than I have physical memory on my latop, so it is paging and swappin and thrashing all the time and loadavg is about 2 (compcache is already in use with usual swap partition as well), but slowly moving forward (Although I afraid it will finally try to allocate 2GB and crash draining 2 days of thrashing). When I want to use the laptop for something else, I stop the process, start X server, firefox and other programs. The problem is that when I start Firefox the loadavg jumps to 10 and the system becomes almost unresponsive at all (long time to turn on/off caps lock, slow mouse cursor position updates, slow switching from X server to Linux console, slow login). The stopped mkcromfs still holds a lot of memory (464.8 MiB and slowly falling) and moves it to swap only when more memory is needed for some other program, which results in a great slowdown. How to tell the Linux to swap out this process entirely (e.g. I'm not intending to resume it in short term), possibly waking from swap other data? Also it will be useful to be able to specify the exact swap device to swap the given process out.

  Read the article

• vSphere education - What are the downsides of configuring virtual machines with *too* much RAM?

  - by ewwhite

  VMware memory management seems to be a tricky balancing act. With cluster RAM, Resource Pools, VMware's management techniques (TPS, ballooning, host swapping), in-guest RAM utilization, swapping, reservations, shares and limits, there are a lot of variables. I'm in a situation where clients are using dedicated vSphere cluster resources. However, they are configuring the virtual machines as though they were on physical hardware. In turn, this means a standard VM build may have 4 vCPUs and 16GB or more of RAM. I come from the school of starting small (1 vCPU, minimal RAM), checking real-world use and adjusting up as necessary. Some examples from a "problem" cluster. Resource pool summary - Looks almost 4:1 overcommitted. Note the high amount of ballooned RAM. Resource allocation - The Worst Case Allocation column shows that these VMs would have access to less than 50% of their configured RAM under constrained conditions. The real-time memory utilization graph of the top VM in the listing above. 4 vCPU and 64GB RAM allocated. It averages under 9GB use. Summary of the same VM What are the downsides of overcommitting and overconfiguring resources (specifically RAM) in vSphere environments? Assuming that the VMs can run in less RAM, is it fair to say that there's overhead to configuring virtual machines with more RAM than they need? What is the counter-argument to: "if a VM has 16GB of RAM allocated, but only uses 4GB, what's the problem??"? E.g. do customers need to be educated? What specific metric should be used to meter RAM usage. Tracking the peaks of "Active" versus time?

  Read the article

• Automatically creating volume partitions on boot

  - by Justin Meltzer

  I followed this guide: http://www.mongodb.org/display/DOCS/Amazon+EC2+Quickstart to set up Mongodb. It had me create a RAID 10 array out of the four devices on EBS. Then it had me create a physical volume, a volume group, and three logical volumes out of that RAID 10 array. Lastly it had me create ext4 filesystems out of the logical volumes and mount them. Now the quickstart guide had me put two things in place so that these steps would be replicated on reboot of the system. It had me add some instructions to the mdadm.conf file to automatically create the RAID 10 array, and it also had me add instructions to the fstab file to automatically mount the filesystem for each logical volume. However, the quickstart guide does not have anything for automatically creating the logical volumes from the RAID 10 array. I checked my system and see that each of the four devices are part of a RAID array: $ sudo mdadm -Q /dev/sdh1 /dev/sdh1: is not an md array /dev/sdh1: device 0 in 4 device unknown raid10 array. Use mdadm --examine for more detail. However, the filesystem is never created or mounted from fstab because it's trying to mount it from logical volumes that were never created (or so it seems). My question is, how can I automatically accomplish all the steps from the quickstart guide on a reboot of the system, and what config file do I need to add data to so that I can automatically create these volume partions after the RAID 10 is created but before the filesystem is mounted. Also I'm unsure whether fstab actually creates and mounts the filesystem or just mounts the filesystem.

  Read the article

• IPTABLES syntax help to forward Remote Desktop requests to a VM [CentOS host]

  - by NVRAM

  I've a VM running MSWindows XP hosted on my CentOS 5.4 machine. I can rdesktop into it from the hosting machine and work just fine using the private ddress (192.168.122.65), but I now need to allow Remote Desktop access from other computers (not just the machine hosting the VM). [Edit] I only need to allow access for a day or so, so don't want to add a NIC (for XP activation reasons). Could someone help me with the iptables syntax? The VM is on a private/virtual network: 192.168.122.65 and my CentOS machine is on a physical network, at 10.1.3.38 (and 192.168.122.1 as the GW for the virtual net). I found this question, but none of the answers seemed to work and I'm a bit timid at blindly trying variations. My FORWARD rules are as listed. Thanks in advance. # iptables -L FORWARD Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable RH-Firewall-1-INPUT all -- anywhere anywhere [Edit] If I do play "blindly" is there a simple way to reset the settings on CentOS (a la service network restart)?

  Read the article

• Setup ejabberd with SQL Server 2008

  - by wonster

  Here's what I have got so far. Windows 2008 Server 64 bit. Installed the latest version of ejabberd, ejabberd-2.1.8-windows-installer.exe. The windows service starts up fine but seems ineffective. However, using the start & stop scripts work. I am able to login to the admin page which so far doesn't seem that versatile. Opened up ports 5222, 5226 and 5280 for my workstation to talk to the server. I've got Spark and Jabbear Windows clients to register, login and instant message with multiple accounts using the server. After confirming that I've got the very basics working, I've decided to make use of SQL Server 2008 as the database. Reason? Mainly, I am very comfortable with SQL Server. I can deal with redundancy, failover, data analysis easily. Not sure if ejabberd's built in DB provides all that. Following the instructions from ejabberd's documentation, I setup a system DSN that points to another physical database. The DSN checks out fine. (Tried both Named Pipes and TCP/IP) Modified ejabberd.cfg. Commented line %%{auth_method, internal} and uncommented line {auth_method, odbc} Uncommented and modified {odbc_server, "DSN=ejabberd;UID=somelogin;PWD=somepassword"}. After making these changes, I restarted. No errors are found in the log files. The jabber clients are no longer able to register new accounts. I'm not sure where to look for errors besides the /logs/ folder as I'm new to all this. I am basically stuck here on step 5. Has anyone got this setup to work recently? Some of the posts I've found around are years old and of no help. I can't be the only one setting up ejabberd with MS SQL. Any help would be appreciated!

  Read the article

• Why can't a PC with 2 network cards be accessed by hostname?

  - by lewis

  I set up PC with 2 network cards, connected to the same LAN. I can connect to this PC (e.g. by remote desktop) only via ip-addresses. Accessing by hostname does not work. Why is this the case? UPDATE: Full environment 1. PC with 2 hardware network adapters. 2. On this PC installed VMWare Workstation. Created 3 VM's, networked by "bridged" network setting in VMWare. 3. In LAN all ip-addresses given from DHCP. 4. Win2k8 on all hosts (both physical and vitrual). As result: 1. PC has 2 ip-address (e.g. 192.168.1.71 and 192.168.1.72). PC available in LAN by ip-addreses, but not avail by hostname. 2. VM's has own ip-addr on each (e.g. 192.168.1.73, *74, *75 etc). They are available from LAN by their ip's, BUT not by their hostnames. How can I access to PC and to VM's by hostname?

  Read the article

• Rescue system running TFS that BSODs, into vmware esxi

  - by 3molo

  Hi, After moving to new facilities, one of our old Dell servers running Windows Server 2003 R2 on PowerEdge 2650 HW BSODs with 0x8e. The server runs Team Foundation Server, so we have a few guys dependent on it. No one here knows TFS, so we have no idea how difficult it would be to setup from scratch. We have the MSSQL database(s) backed up, recent and fresh copy. Tried removing/refitting memory modules, but with no success. The system boots into safe mode but hangs occasionally. I booted a linux livecd and did a dd of both c: and d:, so I have all the data in compressed images on a vmware machine. For the guest, I created a 38G (actually it became 40GB) partition to act as C:, and booted a live cd. I then uncompressed the compressed disk image of c: and dd'd it to the new c: using 'gunzip -dc c.img.gz | dd of=/dev/sda1 bs=1M'. The operation ran for about 1000 seconds, and completed successfully. I assumed it would at least try to boot windows (but most likely BSOD due to not having correct drivers), but the Vmware ESXi guest does not seem to recognize it as a bootable disk. We don't have the vmware enterprise license, so the vmware converter cold cloning is not an option. Did I do something wrong in my dd's etc with the ISOs, or why would it not (try to) boot? Am I wasting my time? What other approach is there? Will continue to try to remove services and drivers to make the physical machine at least work reasonably well in safe mode. What do you suggest? 1. Continue to get the dd'd images to the virtual disk and get it to boot. 2. Install a new windows server, get team foundation server and restore from backup. 3. Focus on the old problematic hardware Any help appreciated

  Read the article

• Client cannot access my IIS7 web server

  - by Soccerwiz

  I have a Windows 2008 web server on running IIS 7 with about 25 websites. One of those sites is an SaaS application that is accessed constantly throughout the day. However, one particular client keeps getting blocked from my server. They will be using the service, and then all of a sudden they cannot access the program, or any other site on the server. The entire office of 4 users is blocked from accessing anything on the web server. A trace route reveals they get all the way to the server before they are blocked. However, they can access a linux server that is a different VM with a different IP on the same physical server. Also, when they are blocked from their office, they can still access the site from their mobile phone or local Starbucks. They can also occasionally reset the router and gain access to the web server again as they are on a dynamic IP address. I checked IIS and allow all IPs to access the server. There is nothing in the logs the says anything about a user being banned. I really have no idea what is causing this? Could it be a virus on their end? I have even moved the SaaS to a completely new server in a different location, and they were working fine for about a month, and then the problem started occurring again. Are there any hidden blacklists in IIS? Or is it a routing issue on their end?

  Read the article

• Siege - running a stress test benchmark

  - by morgoth84

  I need to do a benchmark test of a HTTPS server using Siege, to see how it behaves under massive load. I'm initiating tests from another machine which is quite powerful and it is connected to the same physical switch the server is connected on. But when I initiate a test, I can't get it to make more than 170 requests per second. With this load the server's CPU usage is at 15-20% and the average response time for a request is approx. 0.03 seconds. Load of the client machine is approx. at 10%. So, I gradually increase the number of users in Siege (the number of worker threads) and request rate linearly increases up to 170 reqs/sec, but it never gets over it. No matter how many more worker threads I start, the load on the server is never more than 20% (and the client's load also doesn't increase any more). How can I overcome this? I've googled a bit and found out that after a request is completed, a socket associated with one ephermal port remains in WAIT_TIME state for some time during which it can't be reused. I tried to overcome this by doing these things: sysctl -w net.ipv4.ip_local_port_range="1024 65535" echo 1 > /proc/sys/net/ipv4/tcp_tw_recycle Oh, and the client machine is a Linux (RedHat, I think, but I'm not sure). Any help would be appreciated.

  Read the article

• Kickstarting an Ubuntu Server 10.04 installation (DHCP fails)

  - by William

  I'm trying to automate the network installation of Ubuntu 10.04 LTS with an anaconda kickstart and everything seems to running except for the initial DHCP autoconfiguration. The installer attempts to configure the install via DHCP but fails on its first attempt. This brings me to a prompt where I can retry DHCP and it seems to always work on the second attempt. My issue is that this is not really automated if I have to hit retry for DHCP. Is there something I can add to the kickstart file so that it will automatically retry or better yet not fail the first time? Thanks. Kickstart: # System language lang en_US # Language modules to install langsupport en_US # System keyboard keyboard us # System mouse mouse # System timezone timezone America/New_York # Root password rootpw --iscrypted $1$unrsWyF2$B0W.k2h1roBSSFmUDsW0r/ # Initial user user --disabled # Reboot after installation reboot # Use text mode install text # Install OS instead of upgrade install # Use Web installation url --url=http://10.16.0.1/cobbler/ks_mirror/ubuntu-10.04-x86_64/ # System bootloader configuration bootloader --location=mbr # Clear the Master Boot Record zerombr yes # Partition clearing information clearpart --all --initlabel # Disk partitioning information part swap --size 512 part / --fstype ext3 --size 1 --grow # System authorization infomation auth --useshadow --enablemd5 %include /tmp/pre_install_ubuntu_network_config # Always install the server kernel. preseed --owner d-i base-installer/kernel/override-image string linux-server # Install the Ubuntu Server seed. preseed --owner tasksel tasksel/force-tasks string server # Firewall configuration firewall --disabled # Do not configure the X Window System skipx %pre wget "http://10.16.0.1/cblr/svc/op/trig/mode/pre/system/Test-D" -O /dev/null # Network information # Start pre_install_network_config generated code # Start of code to match cobbler system interfaces to physical interfaces by their mac addresses # Start eth0 # Configuring eth0 (00:1A:64:36:B1:C8) if ip -o link show | grep -i 00:1A:64:36:B1:C8 then IFNAME=$(ip -o link show | grep -i 00:1A:64:36:B1:C8 | cut -d" " -f2 | tr -d :) echo "network --device=$IFNAME --bootproto=dhcp" >> /tmp/pre_install_ubuntu_network_config fi # End pre_install_network_config generated code %packages openssh-server

  Read the article

• Slower/cached Linux file system required

  - by Chopper3

  I know it sounds odd but I need a slower or cached filesystem. I have a lot of firewalls that are syslog'ing their data to a pair of Linux VMs which write these files to their 'local' (actually FC SAN attached) ext3-formatted disks and also forward the messages to our Splunk servers. The problem is that the syslog server is writing these syslog messages as hundreds, sometimes thousands, of tiny ~4k writes per second back to our FC SAN - which can handle this workload right now but our FW traffic's going to be growing by at least a factor of 5000% (really) in coming months and that'll be a pain for the SAN, I want to fix the root cause before it's a problem. So I need some help figuring out a way of getting these writes cached or held-off in some way from the 'physical' disks so that the VMs fire off larger, but less frequent, writes - there's no way of avoiding these writes but there's no need for it to do so many tiny ones. I've looked at the various ext3 options, setting noatime and nodiratime but that's not made much of a dent in the problem. Obviously I'm investigating other file systems but thought I'd throw this out in case others have the same problem in the future. Oh and I can't just forward these messages to Splunk, our firewall team insist they're in their original format for diag purposes.

  Read the article

• a disk read error occurred [closed]

  - by kellogs

  Hi, ¨a disk read error occurred¨ appears on screen after choosing to boot into Windows XP from GRUB. [root@localhost linux]# fdisk -lu Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x48424841 Device Boot Start End Blocks Id System /dev/sda1 63 204214271 102107104+ 7 HPFS/NTFS Partition 1 does not end on cylinder boundary. /dev/sda2 204214272 255606783 25696256 af HFS / HFS+ Partition 2 does not end on cylinder boundary. /dev/sda3 255606784 276488191 10440704 c W95 FAT32 (LBA) Partition 3 does not end on cylinder boundary. /dev/sda4 276490179 312576704 18043263 5 Extended /dev/sda5 * 276490240 286709759 5109760 83 Linux /dev/sda6 286712118 310488254 11888068+ b W95 FAT32 /dev/sda7 310488318 312576704 1044193+ 82 Linux swap / Solaris sda is a 160GB hard disk with quite a few partitions and 3 OSes installed. I am able to boot into Linux and Mac OS fine, but not into Windows anymore. The Windows system is located on /dev/sda1. I can not recall how exactly have I used testdisk but it once said that ¨The harddisk /dev/sda (160GB / 149 GB) seems too small! (< 172GB / 157GB)¨ or something simillar. So far I have tried to ¨fixboot¨ and ¨chkdsk¨ from a recovery console on the affected windows partition (/dev/sda1), the plug off power cord for 15 seconds trick, reinstalling GRUB, repairing the MFT and boot sector of the affected partition via testdisk, what next please ? Thank you!

  Read the article

• HPET missing from available clocksources on CentOS

  - by squareone

  I am having trouble using HPET on my physical machine. It is not available, even though I have enabled it in my bios, forced it in grub, and triple checked my kernel to include HPET in its compilation. Motherboard: Supermicro X9DRW Processor: 2x Intel(R) Xeon(R) CPU E5-2640 SAS Controller: LSI Logic / Symbios Logic SAS2004 PCI-Express Fusion-MPT SAS-2 [Spitfire] (rev 03) Distro: CentOS 6.3 Kernel: 3.4.21-rt32 #2 SMP PREEMPT RT x86_64 GNU/Linux Grub: hpet=force clocksource=hpet .config file: CONFIG_HPET_TIMER=y CONFIG_HPET_EMULATE_RTC=y CONFIG_HPET=y dmesg | grep hpet: Command line: ro root=/dev/mapper/vg_xxxx-lv_root rd_NO_LUKS rd_LVM_LV=vg_xxxx/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_MD SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=vg_xxxx/lv_swap rd_NO_DM LANG=en_US.UTF-8 rhgb quiet panic=5 hpet=force clocksource=hpet Kernel command line: ro root=/dev/mapper/vg_xxxx-lv_root rd_NO_LUKS rd_LVM_LV=vg_xxxx/lv_root KEYBOARDTYPE=pc KEYTABLE=us rd_NO_MD SYSFONT=latarcyrheb-sun16 crashkernel=auto rd_LVM_LV=vg_xxxx/lv_swap rd_NO_DM LANG=en_US.UTF-8 rhgb quiet panic=5 hpet=force clocksource=hpet cat /sys/devices/system/clocksource/clocksource0/current_clocksource: tsc cat /sys/devices/system/clocksource/clocksource0/available_clocksource: tsc jiffies What is even more confusing, is that I have about a dozen other machines that utilize the same kernel .config, and can use HPET fine. I fear it is a hardware issue, but would appreciate any advice or help with getting HPET available. Thanks in advance!

  Read the article

• Allowing Sharepoint to relay email through Exchange

  - by dunxd

  I have written a Sharepoint 2007 web part that sends a field from a form to a specified email address. I have got the form working as I require, but at present it can only send to internal email addresses. Sharepoint's email functions use SMTP to send to our Exchange 2003 server, but because our Exchange server is configured to prevent relaying, if the To: address is not at a local domain, it won't deliver the mail. I don't want to open up our Exchange server to be a completely open relay. What I want is to allow my Sharepoint servers to send mail to addresses outside our domain. The following seem possible: Allow all mail sent from one of the Sharepoint servers to be relayed Allow all mail from a web application pool account to be relayed (I am not sure that the application pool authenticates to the SMTP server though) A combination of the two Can anyone advise on the best way of doing this? Is setting up a dedicated SMTP server on the Exchange server (not a separate physical server) the right way of going about this? EDIT: Note this is for Exchange 2003. There is a post on setting this up in Exchange 2007 which appears to have recognised the frequent requirement to do what I need. It doesn't give much detail on 2003 though. Can anyone expand?

  Read the article

• How to tell Linux to explicitly swap out main memory of suspended process?

  - by Vi

  I run a memory-hungry process (mkcromfs) which consumes more memory than I have physical memory on my latop, so it is paging and swappin and thrashing all the time and loadavg is about 2 (compcache is already in use with usual swap partition as well), but slowly moving forward (Although I afraid it will finally try to allocate 2GB and crash draining 2 days of thrashing). When I want to use the laptop for something else, I stop the process, start X server, firefox and other programs. The problem is that when I start Firefox the loadavg jumps to 10 and the system becomes almost unresponsive at all (long time to turn on/off caps lock, slow mouse cursor position updates, slow switching from X server to Linux console, slow login). The stopped mkcromfs still holds a lot of memory (464.8 MiB and slowly falling) and moves it to swap only when more memory is needed for some other program, which results in a great slowdown. How to tell the Linux to swap out this process entirely (e.g. I'm not intending to resume it in short term), possibly waking from swap other data? Also it will be useful to be able to specify the exact swap device to swap the given process out.

  Read the article

• Boot stuck at blinking cursor before GRUB - only works via BIOS boot menu

  - by delta1

  I have a new box running Debian Squeeze. Grub is installed on /dev/sda, but when booting up I just get a blinking cursor, before the Grub menu. I can only boot to grub successfully when I choose boot options (during post) and select that specific drive! I have made sure the correct drive is set to boot first in the BIOS. So Grub works, but the system won't boot to that drive automatically? Any ideas on what could cause this? Drives sda/b/c are all 2TB (sda runs the system with b/c as raid device md0) with the following partitions: $ cat /proc/partitions major minor #blocks name 8 0 1953514584 sda 8 1 977 sda1 8 2 9765625 sda2 8 3 6445313 sda3 8 4 1937302627 sda4 8 32 1953514584 sdc 8 16 1953514584 sdb 9 0 1953513424 md0 but # fdisk -l /dev/sda gives WARNING: GPT (GUID Partition Table) detected on '/dev/sda'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sda: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sda1 1 243202 1953514583+ ee GPT Any insight into this strange behaviour would be greatly appreciated.

  Read the article

• How to install (old) packages for Ubuntu 9.04?

  - by wchrisjohnson

  Based on some excellent feedback by Mark here (http://serverfault.com/questions/285598/should-i-clone-a-physical-server-to-create-a-vm-for-a-staging-server), today I was able to use the vmware converter to clone my production server for a staging server. However the nic won't come up no matter what I do. I attempted to inistall vmware tools, as I suspect that the fact that it is not installed might prevent the nic from working. (I have the nic set as a vmxnet3 card in the vm settings). The install failed because there were several dependencies missing as well as the Linux headers. Given that Ubuntu 9.04 has been EOL'd, the packages I need to install to get the vmware tools to install are no longer available. I doubt the ubuntu 9.04 install CD has the packages on it. What are my options? I'd rather not upgrade the version of Ubuntu yet, as the point of the vm right now is to maintain parity with the production server. Might I have better luck resetting the driver to use vmxnet2 instead of the vmxnet3? Thanks in advance! Chris

  Read the article

• Why is there an extra HDD under /dev being added in my Linux Kernel?

  - by user1279156

  I have created a Linux kernel and for some reason an extra drive is always added at bootup. My hard drive is listed as /dev/sdb. /dev/sda is created too, and it is 8 MB in size. I can't find anything in the kernel config that is creating this, but if I use a different kernel it is not there. Kernel logs show it as an attached SCSI device, looks just like my hard drive but only 8 MB, and has no partition table. It also doesn't appear to be a physical device. I've tried the kernel on many different models of PCs and it is always there. Does anyone know how to remove it? /dev/disk/by-id gives me: scsi-1AMCC_U21413034D98EB000584 scsi-1AMCC_U21413034D98EB000584-part1 scsi-353333330000007d0 scsi-SATA_ST3250312AS_5VY7SH42 scsi-SATA_WDC_WD800JD-60L_WD-WMAM9Y085675 scsi-SATA_WDC_WD800JD-60L_WD-WMAM9Y085675-part1 scsi-SATA_WDC_WD800JD-60L_WD-WMAM9Y085675-part2 hdparm -i /dev/sda gives me an "invalid argument". dd if=/dev/sda of=sda.img the resulting file does not have any content sdparm results: /dev/sda: Linux scsi_debug 0004 Device identification VPD page: Addressed logical unit: designator type: T10 vendor identification, code set: ASCII vendor id: Linux vendor specific: scsi_debug 2000 designator type: NAA, code set: Binary 0x53333330000007d0 Target port: designator type: Relative target port, code set: Binary transport: Serial Attached SCSI (SAS) Relative target port: 0x1 designator type: NAA, code set: Binary transport: Serial Attached SCSI (SAS) 0x52222220000007ce designator type: Target port group, code set: Binary transport: Serial Attached SCSI (SAS) Target port group: 0x100 Target device that contains addressed lu: designator type: NAA, code set: Binary transport: Serial Attached SCSI (SAS) 0x52222220000007cd designator type: SCSI name string, code set: UTF-8 transport: Serial Attached SCSI (SAS) SCSI name string: naa.52222220000007CD

  Read the article

• Drive letter not appearing after heat-related crash

  - by NickAldwin

  I recently had my old PC (has 3 physical hard drives partitioned into 6 partitions) off while on vacation. When I came back, I turned it on. I hadn't realized the room was warmer than it usually is due to hot weather while I was away. The computer was extremely slow to start up, then it crashed. When i rebooted, it got halfway through chkdsk on one of the non-system partitions, then crashed again. I opened it up and felt the hard drives and immediately shut down the computer and moved it to my basement to cool down because it was so hot. I left it there for a length of time while I reinstalled the A/C. I have now turned it on again. It is working fine, and every drive except for the one with the partition that was being checked has appeared in Windows. I scheduled chkdsk for all of the other partitions anyway, just in case, but I'm worried about that drive. I'm pretty sure the drive itself hasn't broken but that crashing in the middle of a chkdsk repair may have corrupted the data. What would you do in this situation? Most of the data on that drive was backed up, so it's not a huge deal if I lost it, but I'd like to get it back if I could. I also would love to regain usability of the drive, even if I have to wipe it -- but that's a last-resort sort of thing. What do you suggest I do?

  Read the article

• What I should know about memory management?

  - by bua

  first of all: I don't use stackadmin or similar so please don't vote for moving there, I'm reading man top and paper "what every programmer should know about memory ..." I need really simple explanation like for retard ;) Having following top dump: top - 11:21:19 up 37 days, 21:16, 4 users, load average: 0.41, 0.75, 1.09 Tasks: 313 total, 5 running, 308 sleeping, 0 stopped, 0 zombie Cpu(s): 0.4%us, 0.6%sy, 0.9%ni, 96.2%id, 0.1%wa, 0.0%hi, 1.9%si, 0.0%st Mem: 132103848k total, 131916948k used, 186900k free, 54000k buffers Swap: 73400944k total, 73070884k used, 330060k free, 13931192k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 3305 tudb 25 10 144m 52m 940 R 6.0 0.0 1306:09 app 3011 tudb 15 0 71528 19m 604 S 3.3 0.0 171:57.83 app 3373 tudb 25 10 209m 93m 940 S 3.0 0.1 1074:53 app 3338 tudb 25 10 144m 47m 940 R 2.7 0.0 780:48.48 app 4227 tudb 25 10 208m 99m 904 S 1.3 0.1 198:56.01 app 8506 tudb 25 10 80.7g 49g 932 S 2.0 39.6 458:31.22 app I'm wondering what is: RES (my expl. physical memory consumption ? see 49GB) VIRT (memory mapped disk to cache? see 80GB) SHR (shared pages?) Swap: (is this cached label - for memory mapped disk into swap cache?) Should sum of RES give MEM: X used? or maybe sum of VIRT?

  Read the article

• How can I take browser screenshots at a higher resolution than my browser supports?

  - by user53575

  I need to take a screenshot of a website as it would appear on a very high resolution monitor... say 16000x12800 pixels. My laptop's screen has a native resolution of 1280x800. Basically, I need to simulate having a monitor resolution much higher than my monitor and video card actually supports. I want the screenshot of the site to look pretty much how it does when you hit CTRL MINUS (zoom out) in Firefox repeatedly, but without any loss of pixels due to scaling. How can I do this? Is there some way to use virtual machine software to simulate a super-high-res display? If not, is there some way to open a browser window bigger than the screen, and then capture its contents as a PNG somehow? Anything else that might work? Here was an answer: http://superuser.com/questions/120266/how-can-i-take-browser-screenshots-at-a-higher-resolution-than-my-browser-support But it doesn't work. Firefox remains in the resolution of the physical screen. The window blinks and shrinks back to normal resolution. Please Help!!

  Read the article

• How to use LVM on Rackspace Cloud

  - by batrick

  Dear all, I am trying to set up a simple but effective solution to make a backup of my rackspace cloud servers. These servers each run subversion, trac, and some database-backed custom php applications. My idea is to set up a LVM and mount a volume under, say, /srv. In this volume, I keep the data from all applications. Instead of caring about how to back-up each app in a different way (svn hotcopy, trac-admin hotcopy, huge mess for mysql), I simply take an LVM snapshot and back this one up cloud files using the excellent cloudcity script (http://github.com/jspringman/cloudcity/blob/master/cloudcity). The advantage of this solution is that it is quick and easy, and LVM allows to make decent backups. As more apps are added, it should not be required to change the backup script much. The downside, and main point of my question here, is that I am not sure how to get LVM working on Rackspace cloud, because there is only one root volume and no service like Amazon's EBS. I was thinking it may be possible to create a large empty file and use this as a "physical volume". Has anybody done anything like this before? Or do you know why it can never work? It would be great to hear from you. Thanks, batrick

  Read the article

• Exchange 2010 mail routing with Hub Transport in multiple sites

  - by jmreicha

  I have two separate physical sites, Site A and Site B. In site A, I have following: 2 CAS servers 2 Hub Transport servers 2 Mailbox servers 2 Edge servers In site B, I have the following: 1 CAS 1 Hub 1 Mailbox 1 Edge Currently everything is working out of site A. That is, all users are housed on mailboxes that are in site A and all inbound mail flow is pointing to site A. I would eventually like to be able to move some of the mailboxes to site B without causing a disruption for resliency and redundancy purposes but I am not quite sure how to go about setting this up or if it is even possible. So far I have created an Edge subscription in site B and am able to send emails out from test accounts set up with mailboxes on the site B Mailbox server. However, I am unable to receive incoming mail messages and am confused. So I'm thinking incoming mail messages are still being directed to site A and then they are getting stuck because there is no way to route the mail to the site B mailboxes. Is this assumption correct? I am unfamiliar with mail flow and routing so I am not really sure what I need to be looking at? Would I add the site B hub transport to the Edge subscription in site A? Or I guess more specifically, how would I go about enabling communication and mail flow between mailboxes split up on site A and B?

  Read the article

• Optimize Apache performance

  - by Phliplip

  I'm looking for ways to optimize our current web server hosted in-house. I'm trying to supply as much relevant information below. Please let me know if you would require additional information in order to assist. Server is running 1 single website, which is an online pizza ordering platform built on Zend Framework (ver1). On traffic stats from the last month aprox 6.000 pageloads per day, concentrated mainly around dinnertime. Around 1500 loads/hour peaks in that period. We recently upgraded from a 2/2mbit aDSL-line to 100/100mbit fiber, and we still have performance issues at dinner time. We assumed the 2mbit was the issue. Website is pretty snappy in low-load periods. Hardware CPU: Intel(R) Xeon(R) CPU 5160 @ 3.00GHz (3000.13-MHz K8-class CPU) Mem: 328M Active, 4427M Inact, 891M Wired, 244M Cache, 623M Buf, 33M Free Swap: 16G Total, 468K Used, 16G Free (6GB physical, 16GB swap) Filesystem Type Size Used Avail Capacity Mounted on /dev/ad7s1a ufs 4.8G 768M 3.7G 17% / devfs devfs 1.0K 1.0K 0B 100% /dev /dev/ad7s1g ufs 176G 5.2G 157G 3% /home /dev/ad7s1e ufs 4.8G 2.8M 4.5G 0% /tmp /dev/ad7s1f ufs 19G 3.5G 14G 19% /usr /dev/ad7s1d ufs 4.8G 550M 3.9G 12% /var Server OS FreeBSD 8.2-RELEASE Software apache-2.2.17 php5-5.3.8 mysql-server-5.5 Apache footprint (example, taken from # top) 31140 www 1 45 0 377M 41588K lockf 2 0:00 0.00% httpd 31122 www 1 44 0 375M 35416K lockf 2 0:00 0.00% httpd 31109 www 1 44 0 375M 38188K lockf 2 0:00 0.00% httpd 31113 www 1 44 0 375M 35188K lockf 2 0:00 0.00% httpd Apache is using the prefork MPM, APC (Alternative PHP Cache). SSL module is loaded, but not utilized (as in don't really work, thus not used). There is a file containing settings for MPM modules, but as i see it's not included in the httpd.conf file, the include line is commented out. Thus i would guess that the prefork MPM is working of default values too. Here are some other Apache conf values that i found - which are included in https.conf Timeout 300 KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 5 UseCanonicalName Off HostnameLookups Off

  Read the article

< Previous Page | 114 115 116 117 118 119 120 121 122 123 124 125  | Next Page >