Search Results

Search found 10078 results on 404 pages for 'bad man'.

Page 119/404 | < Previous Page | 115 116 117 118 119 120 121 122 123 124 125 126 | Next Page >

Get 5.1 surround sound from computer through a VCR config?

- by Wedding Nails

I'm posting to see if my idea of this setup is right and can be done. I currently have the following "equipment": a JVC VCR -quite old-, which has built in surround sound (aka it has several speaker outputs, which I believe is 5.1 and are connected to several speakers that are in every corner of the room), a computer with SPDIF optical output and a new flat screen TV (with built in HDMI). I want the computer to take advantage of the VCR's surround system (all the speakers in the room) in order to play mainly music and video always with all the speakers (5.1) and with the maximum sound quality. Currently, the computer plays sound only through the front speaker (I connect one output to the on board pc audio input) and the quality is really bad. As a side note, the computer video runs with S-video (old school), and the picture quality as you would imagine, is really bad with the new big LCD screen. My main goals are: to upgrade the picture with a new video card which would support HDMI (my tv has HDMI). to buy a SPDIF optical cable, connect one end to the VCR SPDIF input and the other end to the PC output This is theoretically what I've researched so far, and I came out with several questions: in this case, with the SPDIF cable connected, and all the configurations done in windows allowing the 5.1, will I get every content I play "converted" or played through all of my speakers? (I read this forum post). I already know that in order for this setup to play from all the speakers, the content/audio source has to be 5.1. but my question is, if there is a way to play from all of the speakers no matter what type of content I'm playing (that's why I said conversion there) I already know that HDMI cables carry digital sound. Is there a way I can only use said HDMI cord to the tv, and get sound through the VCR? (I'm not too sure about this, I would have to disable the TVs speakers and use the VCR surround as default, but I have no clue wether this can be done or not). Update: The ultimate question is, do I really have to rely on "sound virtualization" technology to get sound from all the speakers, no matter what content I play? (do I require a newer sound card, like a creative soundblaster with said technology?) Thanks!

Read the article
tomcat6 on ubuntu fails when user set to root

- by J G

I'm well aware that running tomcat6 is really bad from a security point of view - and opens the box it is running on to all kinds of security risks and attack vectors. That said: When I change the entry in the /etc/init.d/tomcat6 to TOMCAT6_USER=root and then run sudo /etc/init.d/tomcat6 start I get [fail] and nothing is written to the logs under /var/log/tomcat6 and no entry for tomcat6 is created under /var/run How do I diagnose what is going wrong?

Read the article
How do you enable syslogd to accept incoming connections on Snow Leopard from remote loggers?

- by Emmel

How do I get syslogd to accept incoming connections from remote hosts on Snow Leopard? I'd like to centralize logging such that various devices and systems send logs to Snow Leopard's syslogd, which normally hangs out on UDP 514. However, I'm unable to get them to successfully be accepted by good ole syslogd. I tcpdumped on the Snow Leopard box to verify that packets are being spouted to port 514 -- they are. I checked that syslogd is listening on 514 -- it's not. Googling around told me that, on older versions of OSX (don't you love the way things change so rapidly on OSX), one just had to add a flag to the syslogd daemon to allow remote; one did this in com.apple.syslogd.plist. However the syslogd daemon has no flags (at least in its man page) that suggests any remote anything. What's the solution to this? Secondary, less import but relevant question: What's 'newsyslog'? I see a plist file but it's not running (apparently). Thanks

Read the article
RabbitMQ and persistence (blocking writes?)

- by daharon

I want to create a RabbitMQ server on a virtual machine (VMware) to be used in production. It will contain persistent queues. I'm wondering if it is a bad idea to store the server on a NAS that's accessed over NFS. Basically my questions are: Will RabbitMQ's writes be blocking? Will the entire queue's operation halt on a write? How much performance degradation should I expect when persisting over NFS?

Read the article
Project Honey Pot - mod_httbl

- by Henko

I'm very interested in project honey pot. It seems like a smart way of blocking harversters etc from your web server. I found out about mod_httpbl for apache but I haven't find much to read about it other than on project honey pot's homepage. Doesn't seem like a very active project(?) Could someone with exeperience of httpbl tell me if mod_httpbl is good/bad or if there are other better alternatives?

Read the article
Is RAID 5 or SnapRAID the better alternative for a media server raid system?

- by rubo77

I am using a raid 5 system for my ubuntu 12.04 xmbc media server with 5 disks. Since the data isn't changing a lot and a total loss wouldn't be so bad, cause I have another backup anyway I am thinking about using SnapRAID It sais: SnapRAID is mainly targeted for a home media center, where you have a lot of big files that rarely change The main advantage for me would be power-saving, cause not all disks have to run all the time. Would you recomment using this? (with a regular resync script once a day)

Read the article
What are RES interrupts (from Munin)

- by grosser

Our server recently had a very bad day, and one of the indicators/reasons seems to be that RES interrupts are douple their normal value, but what does this mean ? (other interrupts: LOC+100%, eth1/TLB +30%)

Read the article
rsync to windows (cygwin)

- by abergmeier

We have a windows file storage (don't ask) and now I want to rsync with the machine from Windows, Mac and Linux. So I installed freeSSHd (login shell is set to C:/cygwin64/bin/sh.exe), set up certificates and testing from Linux the test.dat has 0 bytes: ssh myuser@winmachinename "C:/cygwin64/bin/true.exe" > test.dat Even double checking with actual output works fine: ssh myuser@winmachinename "C:/cygwin64/bin/ls.exe" > test.dat Now, when I call rsync: rsync --progress -avz -e ssh myuser@winmachinename:/c/Users ~/test it fails with: protocol version mismatch -- is your shell clean? (see the rsync man page for an explanation) rsync error: protocol incompatibility (code 2) at compat.c(174) [Receiver=3.1.0] As far as reading the docs, this should not happen, when the first test is successful!? I am by now out of ideas - any recommendations how to debug this? EDIT: | OS | rsync version | |:--------------|:------------------------------------------| | Windows | rsync version 3.0.9 protocol version 30 | | Linux | rsync version 3.1.0 protocol version 31 |

Read the article
issues changing default version when updating Python on Mac

- by Emma

I have a MacBook that came with Python 2.5 installed. I need use a newer version, so I downloaded 3.1 and installed it, then ran the "Update Profile Script" that came with it, which is supposed to change the default version of Python to the one I downloaded. It appeared to run fine and said process completed, but it didn't work. When I type "python" into the terminal it displays version 2.5, and I still can't install pygame, which requires at least Python 2.6. When I do vi .profile I get this: export PATH=.:/opt/local/bin:/opt/local/sbin:$PATH export MANPATH=/opt/local/man:$MANPATH Setting PATH for Python 3.1 The orginal version is saved in .profile.pysave PATH="/Library/Frameworks/Python.framework/Versions/3.1/bin:${PATH}" export PATH ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ".profile" 6L, 251C So it looks like the script did do something, but I don't know enough bash script to understand what. Does anyone know what the issue could be or how to fix it? Thanks a lot!

Read the article
What metric captures why my OSX machine is so slow during XCode indexing

- by Ben Flynn

My entire machine OSX Lion machine slows down while XCode 4.4 is indexing. The CPU is less than 10% busy, I've got over 500 MB free memory, plenty of disk space, disk IO rate is not high, network activity is not high. Indexing just a few files can take minutes and builds are extremely slow. While this is going on, even loading a new web page in Chrome can be slow. Knowing how to fix it would be great, but more fundamentally how can I measure what is actually going slowly? What metrics should I be looking at? Nothing in Activity Monitor, iostat, top, or sar betray anything about what's going on to me. Even getting a man page is interminable.

Read the article
ubuntu 8.04lts + rdiff-backup: Should I install from source instead of using apt repositories?

- by egarcia

I'm trying to use rdiff-backup in order to make backup copies of some folders inside an Ubuntu 8.04LTS server. I'm attempting to do the backup on another server with a more modern Ubuntu distro (9.10). I'll call this one the "client". rdiff-backup needs to be installed on both the client and the server. It is available on the apt repositories on both machines, so I installed it using sudo apt-get install rdiff-backup. The problem is that the version installed on the server is older than the one on the client (1.1.15 vs 1.2.8). Thus I get errors when I try do make them work together. So I need both versions to be the same. What is the standard procedure in these cases? Should I attempt to upgrade the version on the server, or downgrade the version on the client? And how whould I do that? In case it is useful, I'd like to point out that the rdiff-backup apt-package has some dependencies - librsync1 & python-support Attaching the errors I got in case they help: rdiff-backup egarcia@test::/var/rails/ohwr/backup /home/kikito/backup/files Warning: Local version 1.2.8 does not match remote version 1.1.15. Exception ' Warning Security Violation! Bad request for function: rpath.make_file_dict with arguments: ['/var/rails/ohwr/backup'] ' raised of class '<class 'rdiff_backup.Security.Violation'>': File "/usr/lib/pymodules/python2.6/rdiff_backup/Main.py", line 304, in error_check_Main try: Main(arglist) File "/usr/lib/pymodules/python2.6/rdiff_backup/Main.py", line 321, in Main rps = map(SetConnections.cmdpair2rp, cmdpairs) File "/usr/lib/pymodules/python2.6/rdiff_backup/SetConnections.py", line 78, in cmdpair2rp return rpath.RPath(conn, filename).normalize() File "/usr/lib/pymodules/python2.6/rdiff_backup/rpath.py", line 884, in __init__ else: self.setdata() File "/usr/lib/pymodules/python2.6/rdiff_backup/rpath.py", line 908, in setdata self.data = self.conn.rpath.make_file_dict(self.path) File "/usr/lib/pymodules/python2.6/rdiff_backup/connection.py", line 450, in __call__ return apply(self.connection.reval, (self.name,) + args) File "/usr/lib/pymodules/python2.6/rdiff_backup/connection.py", line 370, in reval if isinstance(result, Exception): raise result Traceback (most recent call last): File "/usr/bin/rdiff-backup", line 30, in <module> rdiff_backup.Main.error_check_Main(sys.argv[1:]) File "/usr/lib/pymodules/python2.6/rdiff_backup/Main.py", line 304, in error_check_Main try: Main(arglist) File "/usr/lib/pymodules/python2.6/rdiff_backup/Main.py", line 321, in Main rps = map(SetConnections.cmdpair2rp, cmdpairs) File "/usr/lib/pymodules/python2.6/rdiff_backup/SetConnections.py", line 78, in cmdpair2rp return rpath.RPath(conn, filename).normalize() File "/usr/lib/pymodules/python2.6/rdiff_backup/rpath.py", line 884, in __init__ else: self.setdata() File "/usr/lib/pymodules/python2.6/rdiff_backup/rpath.py", line 908, in setdata self.data = self.conn.rpath.make_file_dict(self.path) File "/usr/lib/pymodules/python2.6/rdiff_backup/connection.py", line 450, in __call__ return apply(self.connection.reval, (self.name,) + args) File "/usr/lib/pymodules/python2.6/rdiff_backup/connection.py", line 370, in reval if isinstance(result, Exception): raise result rdiff_backup.Security.Violation: Warning Security Violation! Bad request for function: rpath.make_file_dict with arguments: ['/var/rails/ohwr/backup']

Read the article
Why does a PDF printed in iWork Pages 09 look crappy in Adobe Reader?

- by Abhic

Hello, I use Snow Leopard at home and work and recently realized that the documents I create in iWork Pages 09 don't look good in Adobe Reader. I go about creating a regular document and 'Print' - Save as PDF in Pages in OS X. The saved PDF file looks great in Preview in OS X but it looks pretty bad in Windows' Adobe Reader and even Adobe Acrobat in OS X. Is there something I could do to make it look better on both platforms? Thank you.

Read the article
printer with win7

- by KareemSaad

I had printer on network and I tried to install it as driver on pc on network it installed but the letters with bad language note . that I installed win7 on pc any one help me

Read the article
printer with win7

- by kareemsaad

I had printer on network and I tried to install it as driver on pc on network it installed but the letters with bad language note . that I installed win7 on pc any one help me

Read the article
printer with win7

- by kareemsaad

I had printer on network and I tried to install it as driver on pc on network it installed but the letters with bad language note . that I installed win7 on pc any one help me

Read the article
Why is Flash power-hungry?

- by Doug

Apple historically argued that Flash was power-hungry, which made it inappropriate for use on mobile devices. I always thought that was just bluster excusing Apple's exclusion of Flash support from their mobile devices. But now I see that Adobe acknowledges that Flash is a pig. Why is it a pig? Are there bad programming approaches (that can be explained in layman's terms) that make it so power-hungry?

Read the article
How to programmatically query bash completion for given string

- by Ryan McKay

I want to ask bash how it would complete a string as if I had typed it in a shell and hit tab. For example, if I type ls /[TAB][TAB] I see the list of files and dirs in / that could possibly complete the ls command. How do I ask bash how it would complete 'ls /' without typing it and hitting tab? I want something like: query_complete 'partial command line string' I read the man page for complete and compgen, but couldn't figure out how to do it with them. Note: 'ls /' is not the actual command I'm interested in, just an example. I am looking for a general solution for any arbitrary string representing a partial command line.

Read the article
Getting NFS clients to retry mount if NFS server down when client boots

- by z0mbix

I have an NFS server that several clients mount. I am using the following in my /etc/exports on the server: /content *(rw,no_root_squash) and on the clients in my /etc/fstab I have: content.prd.domain.tld:/content /content nfs rw,hard,intr 0 0 If the clients boot while the NFS server is down, the share does not get mounted. I read in the NFS man page that the retry defaults should handle this: retry=n The number of minutes to retry an NFS mount operation in the foreground or background before giving up. The default value for forground mounts is 2 minutes. The default value for background mounts is 10000 minutes, which is roughly one week. I have tested this, but it doesn't appear to work. Am I missing something? All servers are RHEL 5.4. Cheers z0mbix

Read the article
esx backup usb disk

- by maruti

my server has a disk error, unfortunately RAID-0. So i am planning to boot it off CD (partedmagic) and copy the VMs to a USB disk. File system is VMFS (esxi4) once the damaged disk is replaced back could the data be restored back? this server has two datastores this bad disk belongs to store-1. please suggest any better ways or tools. thanks in advance

Read the article
Unable to access intel fake RAID 1 array in Fedora 14 after reboot

- by Sim

Hello everyone, 1st I am relatively new to linux (but not to *nix). I have 4 disks assembled in the following intel ahci bios fake raid arrays: 2x320GB RAID1 - used for operating systems md126 2x1TB RAID1 - used for data md125 I have used the raid of size 320GB to install my operating system and the second raid I didn't even select during the installation of Fedora 14. After successful partitioning and installation of Fedora, I tried to make the second array available, it was possible to make it visible in linux with mdadm --assembe --scan , after that I created one maximum size partition and 1 maximum size ext4 filesystem in it. Mounted, and used it. After restart - a few I/O errors during boot regarding md125 + inability to mount the filesystem on it and dropped into repair shell. I commented the filesystem in fstab and it booted. To my surprise, the array was marked as "auto read only": [root@localhost ~]# cat /proc/mdstat Personalities : [raid1] md125 : active (auto-read-only) raid1 sdc[1] sdd[0] 976759808 blocks super external:/md127/0 [2/2] [UU] md127 : inactive sdc[1](S) sdd[0](S) 4514 blocks super external:imsm md126 : active raid1 sda[1] sdb[0] 312566784 blocks super external:/md1/0 [2/2] [UU] md1 : inactive sdb[1](S) sda[0](S) 4514 blocks super external:imsm unused devices: <none> [root@localhost ~]# and the partition in it was not available as device special file in /dev: [root@localhost ~]# ls -l /dev/md125* brw-rw---- 1 root disk 9, 125 Jan 6 15:50 /dev/md125 [root@localhost ~]# But the partition is there according to fdisk: [root@localhost ~]# fdisk -l /dev/md125 Disk /dev/md125: 1000.2 GB, 1000202043392 bytes 19 heads, 10 sectors/track, 10281682 cylinders, total 1953519616 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1b238ea9 Device Boot Start End Blocks Id System /dev/md125p1 2048 1953519615 976758784 83 Linux [root@localhost ~]# I tried to "activate" the array in different ways (I'm not experienced with mdadm and the man page is gigantic so I was only browsing it looking for my answer) but it was impossible - the array would still stay in "auto read only" and the device special file for the partition it will not be in /dev. It was only after I recreated the partition via fdisk that it reappeared in /dev... until next reboot. So, my question is - How do I make the array automatically available after reboot? Here is some additional information: 1st I am able to see the UUID of the array in blkid: [root@localhost ~]# blkid /dev/sdc: UUID="b9a1149f-ae11-4fc8-a600-0d77354dc42a" SEC_TYPE="ext2" TYPE="ext3" /dev/sdd: UUID="b9a1149f-ae11-4fc8-a600-0d77354dc42a" SEC_TYPE="ext2" TYPE="ext3" /dev/md126p1: UUID="60C8D9A7C8D97C2A" TYPE="ntfs" /dev/md126p2: UUID="3d1b38a3-b469-4b7c-b016-8abfb26a5d7d" TYPE="ext4" /dev/md126p3: UUID="1Msqqr-AAF8-k0wi-VYnq-uWJU-y0OD-uIFBHL" TYPE="LVM2_member" /dev/mapper/vg00-rootlv: LABEL="_Fedora-14-x86_6" UUID="34cc1cf5-6845-4489-8303-7a90c7663f0a" TYPE="ext4" /dev/mapper/vg00-swaplv: UUID="4644d857-e13b-456c-ac03-6f26299c1046" TYPE="swap" /dev/mapper/vg00-homelv: UUID="82bd58b2-edab-4b4b-aec4-b79595ecd0e3" TYPE="ext4" /dev/mapper/vg00-varlv: UUID="1b001444-5fdd-41b6-a59a-9712ec6def33" TYPE="ext4" /dev/mapper/vg00-tmplv: UUID="bf7d2459-2b35-4a1c-9b81-d4c4f24a9842" TYPE="ext4" /dev/md125: UUID="b9a1149f-ae11-4fc8-a600-0d77354dc42a" SEC_TYPE="ext2" TYPE="ext3" /dev/sda: TYPE="isw_raid_member" /dev/md125p1: UUID="420adfdd-6c4e-4552-93f0-2608938a4059" TYPE="ext4" [root@localhost ~]# Here is how /etc/mdadm.conf looks like: [root@localhost ~]# cat /etc/mdadm.conf # mdadm.conf written out by anaconda MAILADDR root AUTO +imsm +1.x -all ARRAY /dev/md1 UUID=89f60dee:e46a251f:7475814b:d4cc19a9 ARRAY /dev/md126 UUID=a8775c90:cee66376:5310fc13:63bcba5b ARRAY /dev/md125 UUID=b9a1149f:ae114fc8:a6000d77:354dc42a [root@localhost ~]# here is how /proc/mdstat looks like after I recreate the partition in the array so that it becomes available: [root@localhost ~]# cat /proc/mdstat Personalities : [raid1] md125 : active raid1 sdc[1] sdd[0] 976759808 blocks super external:/md127/0 [2/2] [UU] md127 : inactive sdc[1](S) sdd[0](S) 4514 blocks super external:imsm md126 : active raid1 sda[1] sdb[0] 312566784 blocks super external:/md1/0 [2/2] [UU] md1 : inactive sdb[1](S) sda[0](S) 4514 blocks super external:imsm unused devices: <none> [root@localhost ~]# Detailed output regarding the array in subject: [root@localhost ~]# mdadm --detail /dev/md125 /dev/md125: Container : /dev/md127, member 0 Raid Level : raid1 Array Size : 976759808 (931.51 GiB 1000.20 GB) Used Dev Size : 976759940 (931.51 GiB 1000.20 GB) Raid Devices : 2 Total Devices : 2 Update Time : Fri Jan 7 00:38:00 2011 State : clean Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 UUID : 30ebc3c2:b6a64751:4758d05c:fa8ff782 Number Major Minor RaidDevice State 1 8 32 0 active sync /dev/sdc 0 8 48 1 active sync /dev/sdd [root@localhost ~]# and /etc/fstab, with /data commented (the filesystem that is on this array): # # /etc/fstab # Created by anaconda on Thu Jan 6 03:32:40 2011 # # Accessible filesystems, by reference, are maintained under '/dev/disk' # See man pages fstab(5), findfs(8), mount(8) and/or blkid(8) for more info # /dev/mapper/vg00-rootlv / ext4 defaults 1 1 UUID=3d1b38a3-b469-4b7c-b016-8abfb26a5d7d /boot ext4 defaults 1 2 #UUID=420adfdd-6c4e-4552-93f0-2608938a4059 /data ext4 defaults 0 1 /dev/mapper/vg00-homelv /home ext4 defaults 1 2 /dev/mapper/vg00-tmplv /tmp ext4 defaults 1 2 /dev/mapper/vg00-varlv /var ext4 defaults 1 2 /dev/mapper/vg00-swaplv swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts gid=5,mode=620 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 [root@localhost ~]# Thanks in advance to everyone that even read this whole issue :-)

Read the article
ProFTPD mod_tls is not loaded properly?

- by develroot

The server is running CentOS 5 with DirectAdmin. I am trying to get ProfFTPD work over TLS, however it seems that proftpd is lacking mod_tls support, even though it was compiled with mod_tls. # proftpd -l Compiled-in modules: mod_core.c mod_xfer.c mod_auth_unix.c mod_auth_file.c mod_auth.c mod_ls.c mod_log.c mod_site.c mod_delay.c mod_facts.c mod_ident.c mod_ratio.c mod_readme.c mod_cap.c As you can see there is no mod_tls.c, however, the DirectAdmin configuration file for proftpd suggests that it was built with TLS support: # cat /usr/local/directadmin/custombuild/configure/proftpd/configure.proftpd #!/bin/sh install_user=ftp \ install_group=ftp \ ./configure \ --prefix=/usr \ --sysconfdir=/etc \ --localstatedir=/var/run \ --mandir=/usr/share/man \ --without-pam \ --disable-auth-pam \ --enable-nls \ --with-modules=mod_ratio:mod_readme:mod_tls And all I get when I try to connect over FTPS using FileZilla is: Raspuns: 220 ProFTPD 1.3.3c Server ready. Comanda: AUTH TLS Raspuns: 500 AUTH not understood Comanda: AUTH SSL Raspuns: 500 AUTH not understood Am I missing something? thanks.

Read the article
pam_exec.so PAM module does not export variable PAM_USER as stated in the documentation

- by davidparks21

I'm trying to use the pam_exec.so PAM module to execute a script which needs to know the username/password coming from the application (OpenVPN in this case). I have a script that executes printenv >>afile, but I don't see all the environment variables that the man pages states that pam_exec.so exports (namely PAM_USER I think), I only see the following: PAM_SERVICE=openvpn PAM_TYPE=auth PWD=/usr/local/openvpn/bin SHLVL=1 A__z="*SHLVL I do successfully pick up the password off of STDIN and output it with this same script. But for the life of me I can't get the username. Any thoughts on what I should try next?

Read the article
Proxy / Squid 2.7 / Debian Wheezy 6.7 / lots of TCP Timed-out

- by Maroon Ibrahim

i'm facing a lot of TCP timed-out on a busy cache server and here below my sysctl.conf configuration as well as an output of "netstat -st" Kernel 3.2.0-4-amd64 #1 SMP Debian 3.2.57-3 x86_64 GNU/Linux Any advice or help would be highly appreciated #################### Sysctl.conf cat /etc/sysctl.conf net.ipv4.tcp_tw_reuse = 1 net.ipv4.tcp_tw_recycle = 1 fs.file-max = 65536 net.ipv4.tcp_low_latency = 1 net.core.wmem_max = 8388608 net.core.rmem_max = 8388608 net.ipv4.ip_local_port_range = 1024 65000 fs.aio-max-nr = 131072 net.ipv4.tcp_fin_timeout = 10 net.ipv4.tcp_keepalive_time = 60 net.ipv4.tcp_keepalive_intvl = 10 net.ipv4.tcp_keepalive_probes = 3 kernel.threads-max = 131072 kernel.msgmax = 32768 kernel.msgmni = 64 kernel.msgmnb = 65536 kernel.shmmax = 68719476736 kernel.shmall = 4294967296 net.ipv4.ip_forward = 1 net.ipv4.tcp_timestamps = 0 net.ipv4.conf.all.accept_redirects = 0 net.ipv4.tcp_window_scaling = 1 net.ipv4.tcp_sack = 0 net.ipv4.tcp_syncookies = 1 net.ipv4.ip_dynaddr = 1 vm.swappiness = 0 vm.drop_caches = 3 net.ipv4.tcp_moderate_rcvbuf = 1 net.ipv4.tcp_no_metrics_save = 1 net.ipv4.tcp_ecn = 0 net.ipv4.tcp_max_orphans = 131072 net.ipv4.tcp_orphan_retries = 1 net.ipv4.conf.default.rp_filter = 0 net.ipv4.conf.default.accept_source_route = 0 net.ipv4.tcp_max_syn_backlog = 32768 net.core.netdev_max_backlog = 131072 net.ipv4.tcp_mem = 6085248 16227328 67108864 net.ipv4.tcp_wmem = 4096 131072 33554432 net.ipv4.tcp_rmem = 4096 174760 33554432 net.core.rmem_default = 33554432 net.core.rmem_max = 33554432 net.core.wmem_default = 33554432 net.core.wmem_max = 33554432 net.core.somaxconn = 10000 # ################ Netstat results /# netstat -st IcmpMsg: InType0: 2 InType3: 233754 InType8: 56251 InType11: 23192 OutType0: 56251 OutType3: 437 OutType8: 4 Tcp: 20680741 active connections openings 63642431 passive connection openings 1126690 failed connection attempts 2093143 connection resets received 13059 connections established 2649651696 segments received 2195445642 segments send out 183401499 segments retransmited 38299 bad segments received. 14648899 resets sent UdpLite: TcpExt: 507 SYN cookies sent 178 SYN cookies received 1376771 invalid SYN cookies received 1014577 resets received for embryonic SYN_RECV sockets 4530970 packets pruned from receive queue because of socket buffer overrun 7233 packets pruned from receive queue 688 packets dropped from out-of-order queue because of socket buffer overrun 12445 ICMP packets dropped because they were out-of-window 446 ICMP packets dropped because socket was locked 33812202 TCP sockets finished time wait in fast timer 622 TCP sockets finished time wait in slow timer 573656 packets rejects in established connections because of timestamp 133357718 delayed acks sent 23593 delayed acks further delayed because of locked socket Quick ack mode was activated 21288857 times 839 times the listen queue of a socket overflowed 839 SYNs to LISTEN sockets dropped 41 packets directly queued to recvmsg prequeue. 79166 bytes directly in process context from backlog 24 bytes directly received in process context from prequeue 2713742130 packet headers predicted 84 packets header predicted and directly queued to user 1925423249 acknowledgments not containing data payload received 877898013 predicted acknowledgments 16449673 times recovered from packet loss due to fast retransmit 17687820 times recovered from packet loss by selective acknowledgements 5047 bad SACK blocks received Detected reordering 11 times using FACK Detected reordering 1778091 times using SACK Detected reordering 97955 times using reno fast retransmit Detected reordering 280414 times using time stamp 839369 congestion windows fully recovered without slow start 4173098 congestion windows partially recovered using Hoe heuristic 305254 congestion windows recovered without slow start by DSACK 933682 congestion windows recovered without slow start after partial ack 77828 TCP data loss events TCPLostRetransmit: 5066 2618430 timeouts after reno fast retransmit 2927294 timeouts after SACK recovery 3059394 timeouts in loss state 75953830 fast retransmits 11929429 forward retransmits 51963833 retransmits in slow start 19418337 other TCP timeouts 2330398 classic Reno fast retransmits failed 2177787 SACK retransmits failed 742371590 packets collapsed in receive queue due to low socket buffer 13595689 DSACKs sent for old packets 50523 DSACKs sent for out of order packets 4658236 DSACKs received 175441 DSACKs for out of order packets received 880664 connections reset due to unexpected data 346356 connections reset due to early user close 2364841 connections aborted due to timeout TCPSACKDiscard: 1590 TCPDSACKIgnoredOld: 241849 TCPDSACKIgnoredNoUndo: 1636687 TCPSpuriousRTOs: 766073 TCPSackShifted: 74562088 TCPSackMerged: 169015212 TCPSackShiftFallback: 78391303 TCPBacklogDrop: 29 TCPReqQFullDoCookies: 507 TCPChallengeACK: 424921 TCPSYNChallenge: 170388 IpExt: InBcastPkts: 351510 InOctets: -609466797 OutOctets: -1057794685 InBcastOctets: 75631402 #

Read the article
Unexpected behavior in Bash

- by cYrus

From man bash: A simple command is a sequence of optional variable assignments followed by blank-separated words and redirections, and terminated by a control operator. The first word specifies the command to be executed, and is passed as argument zero. The remaining words are passed as arguments to the invoked command. So it's perfectly legal to write: foo=bar echo $foo but it doesn't work as I expect (it prints just a newline). It's quite strange to me since: $ foo=bar printenv foo=bar TERM=rxvt-unicode [...] Could someone please explain me where I'm doing wrong?

Read the article
Can Resource Governor for SQL Server 2008 be scripted?

- by blueberryfields

I'm looking for a method to, in real-time, automatically, adjust Resource Governor settings. Here's an example: Imagine that I have 10 applications, each hitting a different database on the same database machine. For normal operations, they do not hit the database very hard, so I might want each one to have 10% CPU power reserved. Occasionally, though, one or two of them might spike, and run an operation which could really use the extra power to run faster. I'd like to be able to adjust to compensate (say, reducing the non-spiking apps to 3%, and splitting the difference between the spiking apps). This is a kind of poor man's method of trying to dynamically adjust resource allocation and priorities. Scripts (or something script-like) is preferred, since the requirement is for meta-level adjustments to be possible in real-time, also.

Read the article

< Previous Page | 115 116 117 118 119 120 121 122 123 124 125 126 | Next Page >