Search Results

Search found 3505 results on 141 pages for 'silent installer'.

Page 120/141 | < Previous Page | 116 117 118 119 120 121 122 123 124 125 126 127  | Next Page >

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• How to move the Windows 7 bootloader to the Windows 7 partition?

  - by pauldoo

  I recently installed Windows 7 in a triple boot setup alongside XP and Linux. When I was finished and was in the process of restoring the bootloader for Linux I discovered something strange about what Windows 7 had done. I discovered that Windows 7 had not installed a bootloader to it's own partition, and instead had instead set up a bootloader on the pre-existing XP partition that offers a choice between 7 and XP. This behaviour has been noticed by others. Now my booting is slightly odd. I have GRUB on the MBR which lets me choose between Linux and Windows. When I select Windows I have Grub boot to the XP partition where I get the 2nd choice between 7 and XP. Why doesn't the Windows 7 installer put the Windows 7 bootloader on the Windows 7 partition like all previous MS OSs? This is now going to be a real problem for me, as I now want to wipe the XP partition and install something else there (probably another non-MS OS). How can I move the bootloader for Windows 7 onto the Windows 7 partition, thus making it bootable and allowing me to safely wipe the XP partition?

  Read the article

• CentOS 5.5 remote kickstart installation stalls at "Starting install process." How to debug?

  - by ewwhite

  Hello, I'm having a difficult time with a remote CentOS 5.5 kickstart installation on an HP ProLiant DL360 G6. This is in an environment where I maintain an internal CentOS yum repository. The kickstart installation and post scripts have been tested and normally work. This hardware is also common in this environment, so I do not believe that it is a factor. Unfortunately, I'm having problems with a specific server install. The system is remote to the yum repository at a distance of 500 miles. They are connected over a private low-latency 100-megabit layer 2 connection (26ms round-trip). I'm mounting the 10mb CentOS 5 netinstall ISO image via an HP ILO remote console. The initial boot parameters are: linux ks=http://yum.abctrading.com/prop.cfg ksdevice=eth0 ip=x.x.x.x dns=x.x.x.x netmask=255.255.255.0 gateway=x.x.x.x I'm using the url --url http://ks.abctrading.com/5.5/os/x86_64/ method of installation. This quickly boots into the anaconda installer, pulls the kickstart config and formats the drives. The process eventually halts at the screen below, reading "Starting install process.". Going to the other virtual consoles give the second image below. The process stalls at this point and cannot proceed with the rest of the installation. Running the same kickstart config locally works just fine. I've tried mounting the boot ISO from the console as well as from the ILO2 command line pointing to a locally-hosted boot ISO via http. How can I debug this? Are there any options I've overlooked?

  Read the article

• x display problems in centos 5.5

  - by John Ruiz

  I have a Dell E510 desktop with a geForce 7200 instead of the ATI x600 it came with. I have attempted to install CentOS 5.4 x86_64 (DVD), CentOS 5.5 (net install), and CentOS 5.5 x86_64 (DVD). Gnome desktop. All of these run into the same issue. When I put the DVD into the machine and reboot, the installer begins and I select "graphical install". I see text that say anaconda is starting, and then my screen goes nuts. It's not black, but rather a screen full of diagonal stripes or multiple colors. So I attempted to do a text install of CentOS 5.5 (DVD) and got it installed. When I booted for the first time, I logged into the virtual console and started X (startx). The desktop came up and it already had the display properties GUI up. I changed it from 800x600 to 1680x1050, saw that there were updates available, installed them, and then rebooted. When I start X from the virtual console this time, I get exactly the same display problem as I described before. Does anyone know what might be causing this and what I can do about it? edit: I should also mention that I'm capable of installing Windows 7 and Ubuntu 10.04 onto this machine with absolutely no issues at all.

  Read the article

• How does the "Steam" platform work? Is it DRM? Can I trust "Steam"-powered software? [closed]

  - by Chris W. Rea

  So – I just bought the new game Supreme Commander 2. This question is not about the game, but about the online software installation platform that it seems to require. I haven't bought a game in a long time, and I'm puzzled: Apparently, SC2 is a "Steam"-powered game. When I went to install the game, it asked me to either create a new Steam account, or log in with an existing account. I clicked "Cancel" because I don't plan to play online and I don't want anything unnecessary installed on my computer, since I only plan to play single player! However, after clicking "Cancel", the installer asked for my confirmation that I indeed wanted to cancel installation of the game! I thought I was just canceling the "online" portions! So I really want to know: How do "Steam" powered games work? Is this essentially a form of DRM (Digital Rights Management)? Can I trust this software platform? Has anybody done any independent verification on how this platform works? (I'm very leery of any DRM after the Sony BMG CD copy protection scandal. Thank goodness for Mark Russinovich.) Does the "Steam" platform install anything particularly nasty or unwanted on my computer? High-rep users: Please vote to reopen this question. It is not about the game, but about the software update platform / updater / DRM. Imagine if the software in question were a productivity application. The issues remain the same.

  Read the article

• SQL Server 2008 Cluster Installation - First network name always fails

  - by boflynn

  I'm testing failover clustering in Windows Server 2008 to host a SQL Server 2008 installation using this installation guide. My base cluster is installed and working properly, as well as clustering the DTC service. However, when it comes time to install SQL Server, my first attempt at installation always fails with the same message and seems to "taint" the network name. For example, with my previous cluster attempt, I was installing SQL Server as VSQL. After approximately 15 attempts of installation and trying to resolve the errors, e.g. changing domain accounts for SQL, setting SPNs, etc., I typoed the network name as VQSL and the installation worked. Similarly on my current cluster, I tried installing with the SQL service named PROD-C1-DB and got the same errors as last time until I tried changing the name to anything else, e.g. PROD-C1-DB1, SQL, TEST, etc., at which point the install works. It will even install to VSQL now. While testing, my install routine was: Run setup.exe from patched media, selecting appropriate options After the install fails, I'd chose "Remove node from a SQL Server failover cluster" and remove the single, failed, node Attempt to diagnose problem, inspect event logs, etc. Delete the computer account that was created for the SQL Service from Active Directory Delete the MSSQL10.MSSQLSERVER folder from the shared data drive The error message I receive from the SQL Server installer is: The following error has occurred: The cluster resource 'SQL Server' could not be brought online. Error: The group or resource is not in the correct state to perform the requested operation. (Exception from HRESULT: 0x8007139F) Along with hundreds of the following errors in the Application event log: [sqsrvres] checkODBCConnectError: sqlstate = 28000; native error = 4818; message = [Microsoft][SQL Server Native Client 10.0][SQL Server]Login failed for user 'NT AUTHORITY\ANONYMOUS LOGON'. System configuration notes: Windows Server 2008 Enterprise Edition x64 SQL Server 2008 Enterprise Edition x64 using slipstreamed SP1+CU1 media Dell PowerEdge servers Fibre attached storage

  Read the article

• apache webserver unresponsible with server-status showing all child processes waiting for connection

  - by Jeff

  My setup: i have 3 nearly identical webserver machines serving the same high loaded dynamic website with simple load balancing over dns. The service has been working for over two ears with the same apache config. apache2, php5, ubuntu 8.04 linux 2.6.24-29-server My problem: since about two weeks i'm experiencing problems with this config. Nearly every day i have one small moment about 5 minutes, in which the website is unreachable. I'm still able to login to the servers over ssh. If i run htop, i see the machine simply doing nothing. i have about 1000 apache processes running, but no cpu activity. i've used the apache mod_status to debug this situation. the process scoreboard looks like this: _C.___K_______________________R._______.__K_K____K___C_______.__ _______C__________.___________________________________.________C _.____K__________K___K_WK_____._K_____________________________._ W______K__________K________.____________________._______C_______ _C_.__K__K____.._.._____________________________________C_______ _R___________K___.______C________.C_________.______._____C______ ____________KKC____K_____K__WC_________________C_____.__.____.__ _____________________C_________K______.____C______._____________ _.___C____.___.___________________________.K______.____K________ W__.___________________C.__.____K________K_______R_._.__._______ __C__C_.__________C__C_______._____W______________C_.___C_______ ____.______C_____________C________.____C____________.________._K __.__________.K_____________K_________._____C____.K__________KW_ __K.W________R_________._______.___W___________.____.__K_____W__ W___.___..________W____K Scoreboard Key: "_" Waiting for Connection, "S" Starting up, "R" Reading Request, "W" Sending Reply, "K" Keepalive (read), "D" DNS Lookup, "C" Closing connection, "L" Logging, "G" Gracefully finishing, "I" Idle cleanup of worker, "." Open slot with no current process So the most of the processes are just waiting for connection. after about 5 minutes the situation will return to normal: i have lot least processes on every machine, the most workers have the "."-status (meaing they are open to process a request) and of course the website is reachable! so i'm trying to find something in the logs, but there is simply nothing... the apache access log is silent for about 4 minutes, the same is for the error log. i also can not figure out anything wrong in other system logs. the situation is the same on all 3 webservers (all of them have this load peak and unresposibility at the same time), so i do not thing this is hardware related. but i think, this might be related to some network (tcp) issue. any ideas? EDIT: some more information, that i have just discovered: it has just happened again. and i was able to verify that i'm also not able to connect locally when this problem occurs. i have made some connection statistics with the following command after it happend netstat -an|awk '/tcp/ {print $6}'|sort|uniq -c 109 CLOSE_WAIT 2652 ESTABLISHED 2 FIN_WAIT1 11 LAST_ACK 12 LISTEN 91 SYN_RECV 1 SYN_SENT 16 TIME_WAIT If i execute the same command some time later, i have something like this: 4 CLOSING 108 ESTABLISHED 18 FIN_WAIT1 182 FIN_WAIT2 37 LAST_ACK 12 LISTEN 50 SYN_RECV 11276 TIME_WAIT So in the normal situation i have only 100-200 open connections by clients beeing handled by apache in this moment. when i have this "crash", i have a lot more connections. what is the best way to analyse this? EDIT2: the important lines in apache2.conf are: KeepAlive On MaxKeepAliveRequests 20 KeepAliveTimeout 1 <IfModule mpm_prefork_module> ServerLimit 920 StartServers 30 MinSpareServers 80 MaxSpareServers 120 MaxClients 920 MaxRequestsPerChild 700 </IfModule> it is an apache2 prefork with php_mod. the server has 8GB ram and a 4gb swap partition.

  Read the article

• How to fix a bootable USB Kubuntu installation when the drive has maxed out?

  - by NoCatharsis

  I used Universal-USB-Installer-v1.5.1 from PenDriveLinux.com with Kubuntu 10.04 so I could set up my 4GB flash drive as a totally independent installation. Unfortunately, there was an OS upgrade available which Kubuntu downloaded and attempted to install. This, along with some other software, apparently maxed out my drive before I realized it. Now when I try to boot from the drive, everything boots as normal to the OS boot screen where I select "Boot from this Kubuntu USB Installation." The startup process initiates, then stalls about halfway through and hangs indefinitely. I'm guessing the drive is trying to use space it doesn't have and completely stops working. I realize that once the OS upgrade is in place, the old files could be deleted for a potential 700MB space gain. However, I just have no way to get into the OS and complete the upgrade. My main OS is Windows 7. Is there a way I can fix this issue from within Windows without formatting the entire drive and reinstalling Kubuntu from scratch?

  Read the article

• How does the "Steam" platform work? Is it DRM? Can I trust "Steam"-powered games?

  - by Chris W. Rea

  So – I just bought the new game Supreme Commander 2. This question is not about the game, but about the online software installation platform that it seems to require. I haven't bought a game in a long time, and I'm puzzled: Apparently, SC2 is a "Steam"-powered game. When I went to install the game, it asked me to either create a new Steam account, or log in with an existing account. I clicked "Cancel" because I don't plan to play online and I don't want anything unnecessary installed on my computer, since I only plan to play single player! However, after clicking "Cancel", the installer asked for my confirmation that I indeed wanted to cancel installation of the game! I thought I was just canceling the "online" portions! So I really want to know: How do "Steam" powered games work? Is this essentially a form of DRM (Digital Rights Management)? Can I trust this software platform? Has anybody done any independent verification on how this platform works? (I'm very leery of any DRM after the Sony BMG CD copy protection scandal. Thank goodness for Mark Russinovich.) Does the "Steam" platform install anything particularly nasty or unwanted on my computer?

  Read the article

• Install a KVM guest with LVM partitioning on an LVM partitioned host using virt-install fails, volume group already exists

  - by Rilik84

  our setup consists of a ubuntu 10.04 kvm host server with LVM, on top of which we install the ubuntu 10.04 virtual machines via virt-install and preseed. Each VM has a dedicated logical volume which we pass to virt-install via the "--disk path=/dev/sysvg/vm-name" parameter. The virtual machines themselves are using LVM as well. Virt-install seems to have a few issues with this setup. Say we want to install two virtual machines in parallel. The first vm installs correctly while the second halts during the partitioning, complaining with this error: "volume group name already in use". I tried removing the logical volumes, recreated them, rebooted the kvm host to clear any leftovers but the issue perists. The preseed is telling the vms to create a volume group named "sysvg", which is the same name used by the volume group of the kvm host. Considering this I did another test: I got rid of the preseed part taking care of the partitioning/lvm creation and started the creation of two vms in parallel. If, when prompted, I instruct the vms' installer to do a guided partitioning of the disk with LVM, it will still fail giving this different error on both the vms: Physical Volume /dev/sda5 is already in volume group sysvg. As I wrote, sysvg is the volume group used by the KVM host. So I thought the name clashing was the issue. By removing the preseed part I skipped the volume group naming. I can't understand how the virtual machines would be aware of the presence of that volume group since they're supposed to be isolated from it, especially after I removed and recreated the logical volumes dedicated to them. That detail should not be exposed at all to them! Thanks for the help. I'm clueless.

  Read the article

• Mounting a VirtualBox shared folder on boot with fstab in OpenSuse 11.3

  - by ccook

  I have followed the steps found here, however, the share is not mounted on boot. The share will mount if i run 'mount -a' after booting. Why would the share not mount on boot? 1 - Set up a Virtual Machine and install OpenSUSE 11.2 2 - Create a shared folder on host (HostFolder) 3 - Setup the shared folder in Virtualbox Via the Virtual Machine details or via Devices Shared Folders... 4 - Install dependencies for running the Virtualbox installer You need to install the right development kernelpackage for your machinetype (use 'zypper search -i kernel' to see what's installed) sudo zypper install make gcc kernel-source kernel-hosttype/default-devel 5 - Run the Virtual Machine and go to Devices Guest Additions This mounts an iso image in your OpenSUSE guest. 6 - Open a root terminal and run cd /usr/src/linux make oldconfig && make prepare && make scripts && make dep cp ../linux-obj/$HOSTTYPE/default/Module.symvers . make prepare A commenter on previously mentioned thread says this step is unnecessary but it doesn't work without on my system. I suggest trying step 7 first and returning to step 6 if that fails. * 7 - Run ./VirtualboxLinux yourhosttype .run from the mounted iso image. 8 - Create shared folder in OpenSUSE (GuestFolder) 9 - Test with sudo mount -t vboxsf HostFolder /home/user/GuestFolder It works? Great! Let's set up the system so it automounts for your regular useraccount instead of root-only access. 10 - Add this line to /etc/fstab HostFolder /home/user/GuestFolder vboxsf defaults,uid=1000,gid=1000 0 0 11 - It works for me but if it still doesn't automount after a reboot; sudo mount -a

  Read the article

• Configuring three monitors with two Radeon X1600/X1650 graphics cards under Ubuntu

  - by cpm

  I have three SyncMaster 932a monitors I want to use with two Radeon X1600/X1650 cards under Linux. I am running X.org X Server 1.6.0, as provided by Ubuntu's Wubi installer. After turning off mirroring, I ended up with this xorg.conf: Section "Monitor" Identifier "Configured Monitor" EndSection Section "Screen" Identifier "Default Screen" Monitor "Configured Monitor" Device "Configured Video Device" SubSection "Display" Virtual 2560 1024 EndSubSection EndSection Section "Device" Identifier "Configured Video Device" EndSection The left monitor had a menu bar and a task bar, the center monitor was just desktop, and windows would maximize to the current monitor. The third monitor and second graphics card weren't being used at all. Then I changed my configuration to manually specify each card with their PCI bus: Section "ServerLayout" Identifier "TheLayout" Screen 0 "Radeon Screen 1" Screen 1 "Radeon Screen 2" RightOf "Radeon Screen 1" EndSection Section "Screen" Identifier "Radeon Screen 1" Monitor "Configured Monitor" Device "Radeon the First" SubSection "Display" Virtual 2560 1024 EndSubSection EndSection Section "Screen" Identifier "Radeon Screen 2" Monitor "Configured Monitor" Device "Radeon the Second" EndSection Section "Device" Identifier "Radeon the First" Driver "radeon" BusID "PCI:1:0:0" EndSection Section "Device" Identifier "Radeon the Second" Driver "radeon" BusID "PCI:2:0:0" EndSection Section "Monitor" Identifier "Configured Monitor" EndSection Now both the left and right monitors have task bars and menu bars. Windows cannot be dragged from the first two monitors to the third monitor. Also, maximizing in the left or center window fills both monitors. I also tried adding Option "Xinerama" "true" to the ServerLayout section. X11 wasn't able to start up. I want to: Allow moving windows along all three monitors. Maximizing only fills the current monitor. Either have menu/task bars on only the left monitor or all three monitors How can I make this possible?

  Read the article

• How to install IE9 when KB2120976 is not applicable to my Windows 7 x86 Ultimate edition?

  - by CVertex

  I'm trying to install IE9, visit http://beautyoftheweb.com, download it and then says it's downloading prereqs. After a minute, the installer says there's a problem and directs me to Prerequisites for installing Internet Explorer 9 Beta I click on the x86 installers one by one... most say "already installed".. But http://support.microsoft.com/kb/2120976/ says "The update is not applicable to your computer". Lame. So I try the IE9 install and the go through the whole process again with the same result. I discovered there's an IE9 install log at C:\Windows\IE9_main.log which logs the install process and reports an Error for 2120976 00:06.630: ERROR: Error installing prerequisite file (C:\Users\Vijay\AppData\Local\Temp\IE98036.tmp\KB2120976_x86.msu): 0x80240017 (2149842967) 00:06.677: INFO: PauseOrResumeAUThread: Successfully resumed Automatic Updates. 00:12.090: INFO: Link clicked, opening URL in new window:'http://go.microsoft.com/fwlink/?LinkId=185111' 00:12.106: INFO: Setup exit code: 0x00009C47 (40007) - Required updates are missing from the system.are missing from the system. Any idea why KB2120976 is inapplicable to my LEGAL Windows 7 Ultimate system? Any help is greatly appreciated.

  Read the article

• Completely remove and freshly install MySql on XP?

  - by Corey Ogburn

  I have read this question and have not found it as a solution and I have even attempted much more. I've uninstalled MySql 5.5.18 and deleted: C:\Program Files\MySql C:\Documents and Settings\All Users\Application Data\MySql After uninstalling, I restart the computer. When I reinstall, in the MySql Server Instance Configuration Wizard I leave everything to their defaults except: I add a firewall exception I check Launch MySQL Server Automatically I check Include BIN directory in windows path Enable root access from remote machines (I'll lock that down later, just debugging for now, I have also tried installing without this option to no avail) I've tried Typical and Complete while installing, as well as with and without strict mode. No combination shows a difference. After all this, it cannot Apply Security Settings and I get a 10061 error (it also said error number 2003) and this article didn't help. I've tried everything I can to completely uninstall and successfully reinstall so I can start from scratch. I've uninstalled and reinstalled about a dozen times with minor changes (including turning off the firewall at times), each time deleting the above folders and any proper registry entries with no success. Note by success, applying security settings and a working remote connection. I can connect locally every time, but it's remotely that counts. I have tried to look for exterior problems such as port forwarding in the router and (even though the installer should add it) I do double check the firewall settings, which have always allowed the default port. I'm out of ideas.

  Read the article

• Win7 Ultimate 64bit not finding my SSD, any ideas?

  - by Jakub

  So I am trying to install Windows 7 Ultimate 64bit on my new SSD (Kingston SNVP325-S2/64GB) and I have unplugged my other drives (for the install only). The SSD is detected by BIOS, I am running the latest Firmware for my motherboard P5N-E SLI (775 socket). Upon getting the Windows 7 install screen, it gives me a 'no drives detected'. I have tried Load Driver and downloding nForce drivers (latest for Win7 64bit signed WHQL) results in a message of (something like) "To continue please click Load Driver and load 32-bit and signed 64-bit drivers... blah blah" ... basically it does NOT accept my nForce SATA drivers, nor my 2ndary SATA drivers (JMicron? can't recall the exact name now). I have tried F8 at loading to 'disable driver signing' in hopes that it was an unsigned driver, however nothing works. The SSD is not detected by the Windos 7 installer. I wasted 4 hours on this last night, and gave up, and got nowhere. Anyone heard / ran into this issue before? How can I get the drive detected? Some more details: - Kingston SNVP325-S2/64GB V+ SSD - ASUS P5N-E SLI MOBO - 8GB RAM A-DATA (memory is checked out and fine)

  Read the article

• Thoughts on home NAS server

  - by user826955

  I currently have a NAS with a 2x2TB HDD 1x16GB SSD layout on a mini-itx atom board. The NAS is in a Lian Li PC-Q07 case. On this system I was running freebsd 8 with a gmirror raid 1 setup, which was enough for my needs. So far I was using the NAS for: Fileserver with AFP protocol (only mac clients used) SVN server hosting all my source trees of my projects JIRA (performance was okay-ish) Timemachine backup for the macs The power consumption was about 38W, although I did not put HDDs asleep when unused (I think this is not possible in a raid setup). I liked the NAS because: the performance was good through gigabit LAN (enough for my needs) power consumption was good its a pretty small case and fits in one of my cupboards I disliked the NAS a bit because: it was a bit noisy, the Q07 case vibrated a good amount because of the HDDs. I switched the NAS off every evening I do not have a real backup of the data on the NAS, only the internal raid 1 as safety. I really dont want to loose my source trees under no circumstances, so I would really be sleeping better if I knew I had regular backups somewhere. Recently, the board seemed to have died, I can't boot anymore. Thus, I was thinking about a redesign of my NAS (I still have to find out what parts are broken, I probably need to replace the mainboard and SSD. HDDs seem to be okay). First of all, I was wondering what other users have as backup for their NAS? Are you actually using a second NAS, and regularly copying over the data to have it safe? Or is there any better solution to this? I was thinking about getting a cheap NAS like the synology DS112j with only one disk, and use rsync or something similar to regularly copy data over to the second NAS (wake the second NAS upon start, shut it down after copy). Although this approach seems somewhat weird, It would have the benefit (?) that I could use a single disk instead of raid in the main NAS, and put the disk asleep when idle, and have the NAS running 24/7 with low energy consumption (I found no way to do this with a gmirror setup). Is there any recommended backup solution for a small NAS? Then I was thinking about a different raid setup. Since I have to buy a new mainboard as well as SSD, I might as well switch over to a i3 board with more ram, and also switch to ZFS. I am not familar with ZFS, I've never used it, but I read and hear much about it. Would it be viable to set up a ZFS storage with only 2 disks? Can I easily extend this storage with more disks, once I choose to add some? I could maybe get a new case like the Fractal Design Array R2 which has more 3,5" slots. I could as well get another 2 disks, but I would prefer sticking with the existing 2 for enegery/heat/noise reasons. Should I go for a ZFS storage or stick to my gmirror setup? I would also like to keep freebsd as operating system, and also I dont need any web gui or something (that is, I dont need/want to use FreeNAS or Openfiler etc). Does anyone maybe have a sample setup in use so I can compare energy consumption/noise/software setup? Any guidance towards the NAS of my dreams (silent, low energy, safe w/ backups) much appreciated.

  Read the article

• Where is the bare cygwin package list located and how do I manipulate it?

  - by matnagel

  Where is the bare cygwin package list located and how do I manipulate it programmatically or from a shell or with a different method than the gui? I know the gui (setup.exe), and I'd love to go one or more levels deeper. I can retrieve a list of selected/installed packages ( http://serverfault.com/questions/83456/cygwin-package-management ), but how do I write it back or to a different machine? What I have in mind is when I install a new windows I would like to start with my package list in text form, an apply or inject it somehow to the new system. Where is it? In the registry? In a binary file? in a local database? Or has anybody done this, is there a tool, a tutorial? The essence of what I want is to manipulate the selected package list with something else than the gui. It is ok for me to use the gui for the setup process. So I could imagein manipulating the package List and then run setup.exe and just click through it. Note: I do not want to manipulate the list of already installed packages but of packages that "should be installed". But if htis is not possible, maybe there is some workaround. E.g add an outdated version as installed and the installer will then install the new version.

  Read the article

• Python not Working in Vim

  - by jdg

  I have a new install of VIM from the automatic windows installer: gvim73_46.exe I have Python 2.7 (32 bit) installed. If I open gvim, and type: :set python? I get E518: Unknown option. If I try typing: :python 'hello' Vim crashes. What could be wrong? Here are the contents of :version in case they are helpful, although python is installed, and it is using Python 2.7. I also checked, and C:\Windows\System32\python27.dll is where it should be... I am really lost here. Does anyone have any ideas as to what is going wrong? VIM - Vi IMproved 7.3 (2010 Aug 15, compiled Oct 27 2010 17:59:02) MS-Windows 32-bit GUI version with OLE support Included patches: 1-46 Compiled by Bram@KIBAALE Big version with GUI. Features included (+) or not (-): +arabic +autocmd +balloon_eval +browse ++builtin_terms +byte_offset +cindent +clientserver +clipboard +cmdline_compl +cmdline_hist +cmdline_info +comments +conceal +cryptv +cscope +cursorbind +cursorshape +dialog_con_gui +diff +digraphs -dnd -ebcdic +emacs_tags +eval +ex_extra +extra_search +farsi +file_in_path +find_in_path +float +folding -footer +gettext/dyn -hangul_input +iconv/dyn +insert_expand +jumplist +keymap +langmap +libcall +linebreak +lispindent +listcmds +localmap -lua +menu +mksession +modify_fname +mouse +mouseshape +multi_byte_ime/dyn +multi_lang -mzscheme +netbeans_intg +ole -osfiletype +path_extra +perl/dyn +persistent_undo -postscript +printer -profile +python/dyn +python3/dyn +quickfix +reltime +rightleft +ruby/dyn +scrollbind +signs +smartindent -sniff +startuptime +statusline -sun_workshop +syntax +tag_binary +tag_old_static -tag_any_white +tcl/dyn -tgetent -termresponse +textobjects +title +toolbar +user_commands +vertsplit +virtualedit +visual +visualextra +viminfo +vreplace +wildignore +wildmenu +windows +writebackup -xfontset -xim -xterm_save +xpm_w32 system vimrc file: "$VIM\vimrc" user vimrc file: "$HOME_vimrc" 2nd user vimrc file: "$VIM_vimrc" user exrc file: "$HOME_exrc" 2nd user exrc file: "$VIM_exrc" system gvimrc file: "$VIM\gvimrc" user gvimrc file: "$HOME_gvimrc" 2nd user gvimrc file: "$VIM_gvimrc" system menu file: "$VIMRUNTIME\menu.vim" Compilation: cl -c /W3 /nologo -I. -Iproto -DHAVE_PATHDEF -DWIN32 -DFEAT_CSCOPE -DFEAT_NETBEANS_INTG -DFEAT_XPM_W32 -DWINVER=0x0400 -D_WIN32_WINNT=0x0400 /Fo.\ObjGOLYHTR/ /Ox /GL -DNDEBUG /Zl /MT -DFEAT_OLE -DFEAT_MBYTE_IME -DDYNAMIC_IME -DFEAT_GUI_W32 -DDYNAMIC_ICONV -DDYNAMIC_GETTEXT -DFEAT_TCL -DDYNAMIC_TCL -DDYNAMIC_TCL_DLL=\"tcl83.dll\" -DDYNAMIC_TCL_VER=\"8.3\" -DFEAT_PYTHON -DDYNAMIC_PYTHON -DDYNAMIC_PYTHON_DLL=\"python27.dll\" -DFEAT_PYTHON3 -DDYNAMIC_PYTHON3 -DDYNAMIC_PYTHON3_DLL=\"python31.dll\" -DFEAT_PERL -DDYNAMIC_PERL -DDYNAMIC_PERL_DLL=\"perl512.dll\" -DFEAT_RUBY -DDYNAMIC_RUBY -DDYNAMIC_RUBY_VER=191 -DDYNAMIC_RUBY_DLL=\"msvcrt-ruby191.dll\" -DFEAT_BIG /Fd.\ObjGOLYHTR/ /Zi Linking: link /RELEASE /nologo /subsystem:windows /LTCG:STATUS oldnames.lib kernel32.lib advapi32.lib shell32.lib gdi32.lib comdlg32.lib ole32.lib uuid.lib /machine:i386 /nodefaultlib gdi32.lib version.lib winspool.lib comctl32.lib advapi32.lib shell32.lib /machine:i386 /nodefaultlib libcmt.lib oleaut32.lib user32.lib /nodefaultlib:python27.lib /nodefaultlib:python31.lib e:\tcl\lib\tclstub83.lib WSock32.lib e:\xpm\lib\libXpm.lib /PDB:gvim.pdb -debug

  Read the article

• Can't upgrade NVIDIA GeForce 310M display driver on Acer Aspire 5745PG

  - by Emerson

  I've been for days already trying to update my video driver. I have an Acer Aspire 5745PG with a "NVIDIA GeForce 310M" board, and I was trying to run Sony Vegas video editor with Boris Continunn plugins. It happened that some of the plugins, like BCC Text Extrude wouldn't work, showing the message "Insufficient depth resolution to run Blue". I then read somewhere that updating the display driver would do the trick. That was when my nightmares started, I lost already good 3 nights trying to sort this out, without success :( The display driver that was before (and that I current have after restoring) was the version 8.16.11.8997. First thing I tried was downloading the 8.17.12.6619 driver directly from Acer, which was shown as the latest version from Acer website: http://support.acer.com/product/default.aspx?modelId=2466 Running it would say "Diver Package Failure - Setup failed to read the required Display Driver to be used with this package" I then tried directly the NVIDIA own driver, which the latest was version 296.10: http://us.download.nvidia.com/Windows/296.10/296.10-notebook-win7-winvista-64bit-international-whql.exe That gave me similar error message :/ So after some researching I found out that some people had the same issue and they had to change the configuration file to allow the installer to recognize this NVIDIA board: http://forums.nvidia.com/index.php?showtopic=222904 That topic said to look for the "Device Instance Id" property of the "NVIDIA GeForce 310M" display , which I couldn't find, instead I found the "Hardware Id", which seemed to be the right one. I followed the instructions and changed the inf file first for the Acer installation, and after for the NVIDIA own driver. It actually managed to go ahead with the installation in both instances, but the only thing I got was a black screen, while the computer still apeared to be running fine. I had to hard reset, and then it would come back with generic vga driver. I could only get my display back using the recovery function. I imagine thousands of this notebook was sold, and it can't have its driver updated?? Could someone help me with this?? Thanks Echo

  Read the article

• Windows 7 Won't Boot

  - by Vie

  I recently built a new computer, my fifth one. ASUS Maximus III Formula LGA 1156 Intel P55 ATX Motherboard EVGA 01G-P3-1452-TR GeForce GTS 450 Superclocked 1GB 128-bit GDDR5 PCI Express 2.0 x16 HDCP Video Card COOLMAX RM-1000B 1000W ATX psu Intel Core i7-875K lynnfield 2.93GHz LGA 1156 95w Quad-Core unlocked processor G.SKILL Ripjaws Series 16 (4x4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10666) memory WD VelociRaptor WD3000GLFS 300gb 10000 RPM SATA 3.0Gb/s Hard Drive Sony Optiarc CD/DVD Burner model AD-7261S-0B LightScribe Windows 7 Home Premium 64-bit It gets hung up on the starting windows screen. When I went to install the OS it did the same thing wouldn't go past the windows logo, so I put the new HDD into my old computer and installed windows 7 thinking it was just an installer error. Put the fully installed HDD back into my new machine and it still gets stuck on the starting windows screen. I've tried most everything I've looked up. Disabled USB, Disabled Turbo Boost, Disabled everything that wasn't essential(just about every configuration I can think of), took it apart and put it back together, took all the ram out save one 4g stick(wouldn't even boot when I did this), did a memory scan which came back successful, I don't know what could be wrong. Only thing I can think of is a compatibility issue somewhere, but I've ran over it again and again and I don't know where there would be an issue like that. Need Backup! .<

  Read the article

• Configuring three monitors with two Radeon X1600/X1650 graphics cards under Ubuntu

  - by cpm

  I have three SyncMaster 932a monitors I want to use with two Radeon X1600/X1650 cards under Linux. I am running X.org X Server 1.6.0, as provided by Ubuntu's Wubi installer. After turning off mirroring, I ended up with this xorg.conf: Section "Monitor" Identifier "Configured Monitor" EndSection Section "Screen" Identifier "Default Screen" Monitor "Configured Monitor" Device "Configured Video Device" SubSection "Display" Virtual 2560 1024 EndSubSection EndSection Section "Device" Identifier "Configured Video Device" EndSection The left monitor had a menu bar and a task bar, the center monitor was just desktop, and windows would maximize to the current monitor. The third monitor and second graphics card weren't being used at all. Then I changed my configuration to manually specify each card with their PCI bus: Section "ServerLayout" Identifier "TheLayout" Screen 0 "Radeon Screen 1" Screen 1 "Radeon Screen 2" RightOf "Radeon Screen 1" EndSection Section "Screen" Identifier "Radeon Screen 1" Monitor "Configured Monitor" Device "Radeon the First" SubSection "Display" Virtual 2560 1024 EndSubSection EndSection Section "Screen" Identifier "Radeon Screen 2" Monitor "Configured Monitor" Device "Radeon the Second" EndSection Section "Device" Identifier "Radeon the First" Driver "radeon" BusID "PCI:1:0:0" EndSection Section "Device" Identifier "Radeon the Second" Driver "radeon" BusID "PCI:2:0:0" EndSection Section "Monitor" Identifier "Configured Monitor" EndSection Now both the left and right monitors have task bars and menu bars. Windows cannot be dragged from the first two monitors to the third monitor. Also, maximizing in the left or center window fills both monitors. I also tried adding Option "Xinerama" "true" to the ServerLayout section. X11 wasn't able to start up. I want to: Allow moving windows along all three monitors. Maximizing only fills the current monitor. Either have menu/task bars on only the left monitor or all three monitors How can I make this possible?

  Read the article

• Is my OCZ SSD aligned correctly? (Linux)

  - by Barney Gumble

  I have an OCZ Agility 2 SSD with 40 GB of space. I use it as a system drive in Debian Linux (Squeeze) and in my opinion it's really fast. But I've read a lot on aligning partitions and file systems... And I'm not sure if I succeeded in aligning the partitions correctly. Maybe the SSD could be even faster?? ;-) I use ext4 and here is the output of fdisk -cul: Disk /dev/sda: 40.0 GB, 40018599936 bytes 255 heads, 63 sectors/track, 4865 cylinders, total 78161328 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: [...] Device Boot Start End Blocks Id System /dev/sda1 * 2048 73242623 36620288 83 Linux /dev/sda2 73244670 78159871 2457601 5 Extended /dev/sda5 73244672 78159871 2457600 82 Linux swap / Solaris My partitions were created just by the Debian Squeeze setup assistant. So I didn't care about the details of partitioning. But now I think maybe the installer didn't align it correctly? Actually, 2048 looks good to me (better than odd values like 63 or something like that) but I've no idea... ;-) Help plz! According to some "SSD Alignment Calculator" I found on the web, the OCZ SSDs have a NAND Erase Block Size of 512kB and their NAND Page Size is 4kB. 2048 is divisible by 4 and 512. So are the partitions aligned correctly?

  Read the article

• How do I install Windows XP from an external hard drive?

  - by Plasmer

  I'm trying to install Windows XP Media Center edition by copying the install disc image to an external hard drive and making it bootable. Has anyone had success getting this to work on systems that can't boot from dvds/floppies? I'm basically working from this guide: http://www.dl4all.com/other/21495-install-windows-xp-from-usb.html Update - 2/15/10 I used WinToFlash on my laptop to format my usb hard drive from my install dvd (Windows XP Media Center Version 2005 with Update Rollup 2 from Dell) and selected "boot from usb device" at the boot selection menu and the windows installer started up. However, an error message came up saying that: "A problem has been detected and windows has been shut down to prevent damage to your computer." Originally on my desktop machine, I had 1 150Gb SATA drive, and 2 150 Gb SATA drives striped together using RAID. From the hard drive diagnostics, it appears the windows install on one of the RAIDed disks lost a block and this has been preventing me from booting up. I replaced the standalone drive with a new 1Tb SATA drive and disconnected the other hard drives. Could the message be indicating a virus is on the unformatted drive? or the usb hard drive? Update 2 - 2/15/10 The external hard drive didn't find any viruses when scanned. I tried installing Vista Home Premium 64bit SP1 using WinToFlash and that installed successfully onto the new 1Tb drive. WinToFlash was really easy to use and helped a lot, thanks!

  Read the article

• Windows + Django + mod_wsgi = "DLL load failed"

  - by Kyle MacFarlane

  For a long time I was using Python 2.5 to do all this fine but recently upgraded to 2.7 since building stuff for 2.5 is a real pain. I also updated mod_wsgi to 3.3 for Python 2.7. Everything is working fine with Apache + mod_wsgi on CentOS and also in the Django runserver on both Windows and CentOS, but not with Apache + mod_wsgi on Windows. Whenever I try to access a page in my Django app I get the following (note that Apache starts fine): ImportError at / DLL load failed: The specified module could not be found. Which is caused by things like: from Crypto.Cipher import AES Etree and others cause the exact same error and it is not limited to any specific packages. Anything with pyd files fails. Googling around suggests reinstalling Python "for all users", but the installer doesn't give you that option anymore anyway. For good measure I've tried reinstalling Python 2.7 as an administrator and also told it to register itself as the default version of Python but neither helped. I think the solution might have something to do with: The fact that I have 2.5, 2.6 and 2.7 installed on this machine and mod_wsgi might be loading the DLLs for 2.5 instead of 2.7. Something to do with WSGIPythonPath, which I usually don't need to set.

  Read the article

< Previous Page | 116 117 118 119 120 121 122 123 124 125 126 127  | Next Page >