Search Results

Search found 3993 results on 160 pages for 'broken pipe'.

Page 121/160 | < Previous Page | 117 118 119 120 121 122 123 124 125 126 127 128  | Next Page >

• Cannot load from raid with grub

  - by Andrew Answer

  I have a RAID1 array on my Ubuntu 12.04 LTS and my /sda HDD has been replaced several days ago. I use this commands to replace: # go to superuser sudo bash # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded" # remove broken disk from RAID mdadm /dev/md0 --fail /dev/sda1 mdadm /dev/md0 --remove /dev/sda1 # see partitions fdisk -l # shutdown computer shutdown now # physically replace old disk by new # start system again # see partitions fdisk -l # copy partitions from sdb to sda sfdisk -d /dev/sdb | sfdisk /dev/sda # recreate id for sda sfdisk --change-id /dev/sda 1 fd # add sda1 to RAID mdadm /dev/md0 --add /dev/sda1 # see RAID state mdadm -Q -D /dev/md0 # State should be "clean, degraded, recovering" # to see status you can use cat /proc/mdstat After bebuilding completion "fdisk -l" says what I have not valid partition table /dev/md0. So 1) "update-grub" find only /sda and /sdb Linux, not /md0 2) "dpkg-reconfigure grub-pc" says "GRUB failed to install the following devices /dev/md0" I cannot load my system except from /sdb1 and /sda1, but in DEGRADED mode... This is my partial fdisk -l output: Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000667ca Device Boot Start End Blocks Id System /dev/sdb1 * 63 940910984 470455461 fd Linux raid autodetect /dev/sdb2 940910985 976768064 17928540 5 Extended /dev/sdb5 940911048 976768064 17928508+ 82 Linux swap / Solaris Disk /dev/md0: 481.7 GB, 481746288640 bytes 2 heads, 4 sectors/track, 117613840 cylinders, total 940910720 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table Anybody can resolve this issue? I have big headache with this.

  Read the article

• Concatenating ogg video files from the command line

  - by Noufal Ibrahim

  Okay. I've got a few ogg files I've created using a desktop recording tool. I've transcoded them using ffmpeg once (mainly to clip out the beginnings and the ends). Now, I have 3 such files which I want to concatenate into a single .ogv file. I tried using oggCat, it crashed with some kind of error (I tried concatenating a file to itself using oggCat and that failed too leading me to believe that my distro is shipping a broken version of the package). Simply cating the files works but I can't seek which is not cool. mencoder run like this mencoder -ovc lavc -oac lavc file1.ogv file2.ogv file3.ogv -o complete.ogv. It transcodes the files into an avi and clips off a little of the 3 videos. So, how do I do this? Update 1: My current workaround is to transcode the 3 files into .mpg using ffmpeg, then cating them together and then transcoding them back into ogv. Update 2: PiTiVi works for this kind of thing but I need something from the command line that I can automate and script.

  Read the article

• Broke NetBeans file associations in Windows XP how do I get them back?

  - by Serhiy

  Hello... I broke my file association in XP... Does anyone have any clue how to fix it? When I right click and select Open With... the application I want to use (NetBeans) to open the file is not on the list... and when I browse for it it won't let me select it (well it does but then won't add it to the list). The way I broke it is by installing 6.7 and then uninstalling 6.5.... since then my file associations have all been broken. I even tried uninstalling NetBeans and reinstalling it again... no luck... I even went as far as adding my own action called "OpenIt" to the file types I wanted... and that works... but only if the file/folders that contain in don't have any spaces... otherwise NetBeans throws a ".....does not exist, or is not a plain file". Thus nothing off the desktop can be opened... Does anyone know of how I can fix this problem? Thanks.

  Read the article

• Debian/Ubuntu - No network connection

  - by leviathanus

  I have a very weird situation on my Ubuntu 12.04 LTS Server. I can not access (ping) my gateway, although I believe my config is ok - I attach the outputs. Any hints where to look? (I changed the beginning of the IP to something different, just obfuscation) ping 5.9.10.129 PING 5.9.10.129 (5.9.10.129) 56(84) bytes of data. From 5.9.10.129 (5.9.10.129) icmp_seq=2 Destination Host Unreachable From 5.9.10.129 (5.9.10.129) icmp_seq=3 Destination Host Unreachable From 5.9.10.129 (5.9.10.129) icmp_seq=4 Destination Host Unreachable uname -r 3.2.0-29-generic ifconfig eth0 eth0 Link encap:Ethernet HWaddr 3c:97:0e:0e:54:d7 inet addr:5.9.10.142 Bcast:5.9.10.159 Mask:255.255.255.224 inet6 addr: fe80::8e70:5aff:feda:c4ac/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1216 errors:0 dropped:0 overruns:0 frame:0 TX packets:490 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107470 (107.4 KB) TX bytes:34344 (34.3 KB) Interrupt:17 Memory:d2500000-d2520000 ip route default via 5.9.10.129 dev eth0 metric 100 5.9.10.128/27 via 5.9.10.129 dev eth0 5.9.10.128/27 dev eth0 proto kernel scope link src 5.9.10.142 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 5.9.10.129 0.0.0.0 UG 1000 0 0 eth0 5.9.10.128 5.9.10.129 255.255.255.224 UG 0 0 0 eth0 5.9.10.128 0.0.0.0 255.255.255.224 U 0 0 0 eth0 iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination UPD: Eric, this is how routing information looks on a working server: 0.0.0.0 78.47.198.49 0.0.0.0 UG 100 0 0 eth0 78.47.198.48 78.47.198.49 255.255.255.240 UG 0 0 0 eth0 78.47.198.48 0.0.0.0 255.255.255.240 U 0 0 0 eth0 As I understand it, Hetzner tries to ensure security by this, so I can not take over an IP by changing my MAC. But this is another server, which has another netmask (255.255.255.240) UPD2: BatchyX, on the working server: 78.47.198.49 dev eth0 src 78.47.198.60 cache on the broken: 5.9.10.129 dev eth0 src 5.9.10.142 cache

  Read the article

• When did my LaTeX files become TeX files!?

  - by andrz_001

  After transferring all my files onto a new machine, all files that were once LaTeX files (having the texnic center "T" icon) are now TeX files (having the TeX works icon --I don't remember installing that one!). But....the files are associated with the technic center! In other words, the files open with the texnic center, yet the "type of file" is "tex document". I'm using the same miktex distrubution and texnicCenter (both for windows xp) as on the old machine. Again, I don't know how/where I got this texworks on the new machine--assuming it came with windows. A question: Could these tex associations cause me any new surprises, anything unexpected? Like certain packages not working, etc? Because I can't have that!! Should I not fix it if it ain't broken!? For instance, one particular file yesterday would not produce any pdf output after compiling...after trying many things (other files compiled as they should have), I got to thinking to try it without the setspace for doublespacing!! And it worked. I have no idea why. Anyway.... Real question: How to revert to LaTeX file associations?? Rhetorical question: Would this question have better luck in ctan or stackoverflow? I guess I'll find out! Thank you wholeheartedly!

  Read the article

• How to setup Python with Lighttpd and FastCGI (like PHP)

  - by johndir

  Running Lighttpd on Linux, I would like to be able to execute Python scripts just the way I execute PHP scripts. The goal is to be able to execute arbitrary script files stored in the WWW directory, e.g. http://www.example.com/*.py. I would not like to spawn a new Python instance (interpreter) for every request (like done in regular CGI, if I'm not mistaken), which is why I'm using FastCGI. Following Lighttpd's documentation, the following is the FastCGI part of my config file. The problem is that it always runs the /usr/local/bin/python-fcgi script for every *.py file, regardless of the content of that file: http://www.example.com/script.py [output=>] "python-fcgi: test" (regardless of the content of script.py) I'm not interested in using any framework, but simply executing individual [web] scripts. How can I make it act like PHP, executing any script in the WWW directory by requesting it's path? /etc/lighttpd/conf.d/fastcgi.conf: server.modules += ( "mod_fastcgi" ) index-file.names += ( "index.php" ) fastcgi.server = ( ".php" => ( "localhost" => ( "bin-path" => "/usr/bin/php-cgi", "socket" => "/var/run/lighttpd/php-fastcgi.sock", "max-procs" => 4, # default value "bin-environment" => ( "PHP_FCGI_CHILDREN" => "1", # default value ), "broken-scriptfilename" => "enable" ) ), ".py" => ( "python-fcgi" => ( "socket" => "/var/run/lighttpd/fastcgi.python.socket", "bin-path" => "/usr/local/bin/python-fcgi", "check-local" => "disable", "max-procs" => 1, ) ) ) /usr/local/bin/python-fcgi: #!/usr/bin/python2 def myapp(environ, start_response): start_response('200 OK', [('Content-Type', 'text/plain')]) return ['python-fcgi: test\n'] if __name__ == '__main__': from flup.server.fcgi import WSGIServer WSGIServer(myapp).run()

  Read the article

• Recover data from physically damaged harddrive. What are my options?

  - by Michael Kniskern

  I was trying to replace the power supply in my desktop PC and ended up physically damaging the data connection from the hard drive to the motherboard. The plastic shelf for the copper prongs on the hard drive broke into the cable. Here is a picture of my handy work: I went to Best Buy Geek Squad to discuss my options and they said that they will need to send it to the recover center it could cost anywhere between $250 to $1600 USD to recover the data out the hard drive Is this reasonable for data recovery from a physically damaged hard drive? Are there any other options I can explore? I am going to talk to the data doctors to see what my options are. Update I took the HD to Data Doctors, and they told me that the SATA connection was broken to they would need to replaced the data connector and then copy the data to a brand new hard drive. So, with the initial analysis, cost of replacement parts, and data recovery fee it came out to $865.00 USD. The technician specifically stated if this was an older hard drive that would just need to replace the data connector. But because there is specific information related to the individual hard drive in the flash ROM, they need to transfer the data to a brand new hard drive.

  Read the article

• How to remove static IP from Mitel 5312 and enable DHCP

  - by jimbo

  I'm not sure this is the right forum for this question -- although I'm confident I'll be told if not! -- but I've read the fine manual (at least, such a manual as I have), I've googled and I cannot get any insight into where to even start solving this problem. I have a bunch of Mitel 5312 handsets, talking to a 3300 ICP controller. Some handsets are at a remote location, get an address from my DHCP server over there, and use the Mitel "Teleworker" extension to connect in over the Internet. The remaining handsets were set up with static IPs by a BT-supplied engineer, on the same subnet as the ICP itself. So far, so good. I have one remaining teleworker licence, and need to move a handset from the home location to the remote. I've managed to boot it and configure teleworker, but I cannot for the life of me see where I tell it to forget its static IP, and make a DHCP request. Any ideas? Should I be looking on the controller, or holding magic combinations of buttons on the handset itself? EDIT: Following some advice from Robert, below, I've broken out a spare device and reassigned the profile for this user's extension to the MAC of the new phone, and a new profile to the old MAC. Unfortunately this still doesn't get me anywhere -- the new handset now asks for the teleworker install password. I suspect I'm going to have to get a Mitel engineer involved here, since I've never been given that password... Unless anyone has any great ideas?

  Read the article

• How do I repair my Logitech Anywhere MX?

  - by Stefano Palazzo

  My Anywhere Mouse has got mushy mouse button syndrome. That is, the left mouse button feels a little bit soft, and it easily double clicks, let's go when I drag something. Before I repair it at home, rather than bringing it to the store (I kind of need it, it's the only one I have), I'd like to know exactly what I'm doing. It'd be too bad if I tried to repair it, voided the warranty and didn't succeed. I'm guessing there are screws to open it under the rubber pads. And I suppose I can take those off without breaking them, and put them back on without bending them. How is this mouse held together, and what's the safest way to open it? Once I have it open, will I be able to fix the problem? What's causing the mushy mouse button? Here's what I know so far: It might be the switch itself that's broken, in which case I shouldn't open it (I can't get a replacement, voiding the warranty to "have a look" seems pointless) If there are screws underneath the rubber pads, they're only on the 'front', the back two thirds of the mouse are all battery cover: There's nothing I can see under the batteries either. In the mouse I had before this one, there were sort of springy things connecting the actual button with the switch soldered to the board. They were just lying inside of a bit of plastic, and I could swap the left and right ones easily. If repairing it is more difficult, transferring the problem to the right mouse button would be a very good start.

  Read the article

• Permissions nightmare - tried all I know

  - by Ben

  Working on a new client's dev site, which is a wordpress install on a Plesk box. I have SSH root access, and FTP access through a separate account. What I've done so far Initially I couldn't make any changes to any files at all. The permissions on all the template files looked a little screwy (644), so I figured change them to allow group, and add myself to the group: CHMOD Recursive on the theme folder to set everything to 664 Quickly realised I'd broken it, set the folders to 755, kept files as 664 Ownership on all files is a mixture of root:root and 500:500 (there is no user nor group with the ID of 500 on the server). Added myself to the group 'root' so I could modify the files too The Problem This worked OK, in terms of being able to edit the existing files, so I began working. However, I can't upload to the directory, even having run CHOWN -R root:root templatefolder/ and being in the root group. I feel like I must be missing something obvious, and it's doing my head in. Questions: Files in the install owned by 500 with group 500 - I've looked in /etc/group and /etc/passwd and there is no user nor group with this ID. Is that left over from another developer's setup or the previous server (they moved recently)? Is being in the 'root' group enough, or do I need to own the theme folder as 'myftpuser' in order to upload and create new files? Like I say, I have edit access, so I got myself this far. I'm now questioning what to do next!

  Read the article

• Security implications of adding www-data to /etc/sudoers to run php-cgi as a different user

  - by BMiner

  What I really want to do is allow the 'www-data' user to have the ability to launch php-cgi as another user. I just want to make sure that I fully understand the security implications. The server should support a shared hosting environment where various (possibly untrusted) users have chroot'ed FTP access to the server to store their HTML and PHP files. Then, since PHP scripts can be malicious and read/write others' files, I'd like to ensure that each users' PHP scripts run with the same user permissions for that user (instead of running as www-data). Long story short, I have added the following line to my /etc/sudoers file, and I wanted to run it past the community as a sanity check: www-data ALL = (%www-data) NOPASSWD: /usr/bin/php-cgi This line should only allow www-data to run a command like this (without a password prompt): sudo -u some_user /usr/bin/php-cgi ...where some_user is a user in the group www-data. What are the security implications of this? This should then allow me to modify my Lighttpd configuration like this: fastcgi.server += ( ".php" => (( "bin-path" => "sudo -u some_user /usr/bin/php-cgi", "socket" => "/tmp/php.socket", "max-procs" => 1, "bin-environment" => ( "PHP_FCGI_CHILDREN" => "4", "PHP_FCGI_MAX_REQUESTS" => "10000" ), "bin-copy-environment" => ( "PATH", "SHELL", "USER" ), "broken-scriptfilename" => "enable" )) ) ...allowing me to spawn new FastCGI server instances for each user.

  Read the article

• How to configure a trusted connection between IIS 7 and SQL Server 2005?

  - by user1180652

  How do configure a trusted connection between IIS 7 and SQL Server 2005? My webapp was working fine with Windows Authentication enabled in IIS. Now, in order to solve a problem, we need to use a trusted connection. Unfortunately, enabling the trusted connection in the web.config broke the webapp. Oddly enough, when I run this application with trusted connection from my local dev machine (using the Cassini web server) IIS (Windows Server 2008) is running on one machine. The database (SQL Server 2005 but could migrate to 2008) is running on another machine. We are on a Windows domain running AD. All traffic is within our own firewall - no public access. Beyond that, I can't provide much info but I can find it. We're very "compartmentalized" (we have server people, security people, oracle people, SQL Server people, etc.) Thanks! Update 02/14/2012 0902: The webapp is now functional (app no longer broken) but the main issue is still unresolved. Now I have the app's application pool running as a domain account with permissions on the SQL Server box and IIS box. We were using this account to run the application but, and here's the problem, we need to log the real user name that made a change. When using the service account, the name of that service account appeared in the audit tables, making the auditing quite useless. So, not I'm at least running again. The connection string in the web.config is using "Trusted_Connection=True", the appPool is using a domain account with access to both boxes, BUT when I make a change (logged in as me) the name of the service account (appPool identity) is still logged in the audit tables. I also manually granted full permissions to the service account on the webapp folder. What do I need to do in order to log my name, not the service account, in the audit tables? Everything I'm reading says I need to establish a trusted connection between the two servers.

  Read the article

• All commands stopped working in centos 6.5

  - by Michael

  I have made a big mistake while removing some duplicate packages as it appears to be broken. yum 1036 rpm -e --nodeps glibc-2.12-1.132.el6_5.2.x86_64 1037 rpm -e --nodeps nscd-2.12-1.132.el6_5.2.x86_64 1038 rpm -e --nodeps glibc-common-2.12-1.132.el6_5.2.x86_64 1040 rpm -e --nodeps glibc-common-2.12-1.132.el6.x86_64 glibc-devel-2.12-1.132.el6.x86_64 glibc-headers-2.12-1.132.el6.x86_64 1041 rpm -e glibc.x86_64 1042 rpm -e --nodeps glibc.x86_64 The issue happened after doing 1042 step. None of commands work(including yum, rpm, ls, cp etc) and getting error /lib64/ld-linux-x86-64.so.2: bad ELF interpreter: No such file or directory I thought that installing glibc after removing all the current ones would help to resolve the duplicate package error :( Now I realised that it is used as the C library in the GNU system and most systems with the Linux kernel. It defines the "system calls" and other basic facilities such as open, malloc, printf, exit, etc. Is there any possible solutions other than reinstall? I have lost ssh access. Maybe anything can be done using rescue cd? Thanks

  Read the article

• How to figure out what VirtualBox did?

  - by AndrejaKo

  I'm trying to boot a custom made-in-ASM OS on my recent laptop. The OS is intended to be installed on a floppy and during make creates a bootable floppy. Since I don't have a floppy drive, I installed it on a virtual floppy. After that I used WinToFlash's create bootable MS-DOS USB drive option to transfer the floppy image to an USB flash drive. Then I tried to boot my computer from it but got only a repeating broken string on screen. After all that I made a virtual hard disk image form the flash drive using this tutorial and tried to boot a virtual machine from it. First time I got same problem as on real computer. I then used the reset option and next time and every time after that OS booted correctly. My question is: How do I figure out what exactly happened to the virtual machine between first and second boot? UPDATE I just created a new VM with default settings for windows XP and it has the same problem that I have on a real computer. I was unable to reproduce the procedure which made the first VM work correctly.

  Read the article

• Repairing hard disk when Windows installation disk won't boot

  - by Echows

  I'm trying to recover some data from a faulty hard disk with Windows installed on it (on which Windows won't even boot). I have tried so far: Booting to Ubuntu live USB stick and running ntfsfix (didn't work) Trying to mount the broken partition when running Ubuntu from usb stick (doesn't mount) Running photorec image recovery tool from live Ubuntu (it found some stuff but not the images I was looking for) Now as a last resort I got myself a Windows installation on a USB stick so that I can try fdisk, but the installer doesn't work. The loading screen shows up and then the installer crashes. The installer works fine on other computers. I suspect that the installer is trying to read the hard drive to see if there's something there but when it can't read one partition, it crashes. On Ubuntu, I can mount other partitions except the one I'm interested in so at least the hard drive is not completely dead. So the question is, what options do I have left? To be more specific, my goal is to recover some images from the faulty ntfs-partition on the hard drive. Other than that, I don't care about the contents of the hard disk.

  Read the article

• LG LW20 Express won't boot after hdd replace

  - by Mika

  My old laptop (LG LW20 Express) got a hdd failure and I replaced the hdd. Now the laptop won't boot from cd or usb. I'm trying to install ubuntu on it. When I turn the laptop on it shows me the startup screen but when it should be the time to load operating system it just gives a black screen and starts over. This loop continues until I shut down the laptop. I created the usb boot drive following this guide https://help.ubuntu.com/community/Installation/FromUSBStick/ I used my boot cd to install ubuntu on this machine I'm using right now. So at least the cd should work. From the BIOS I can see that my newly installed hdd is recognized and put as a secondary master. Also the cd and removable media are in the boot list before hdd. The laptop runs pretty hot. The fan is at full speed pretty soon after the laptop is turned on. Earlier I suspected that it would have been the almost broken hdd that would have produced that heat but there obviously is something else also. Any ideas what to check?

  Read the article

• Visual Studio 2010 won't compile/create new projects

  - by tuner

  My Visual Studio 2010 Professional with SP1 installed won't compile anymore. The shown error is: TRACKER : error TRK0005: Failed to locate: "CL.exe". The system cannot find the file specified. Strangely it is also not possible anymore to create new projects - the wizard appears but just restarts when I press create. As I found out the paths for Visual Studio are now built from settings in the registry. Namely HKEY_CURRENT_USER\Software\Microsoft\VisualStudio. Comparing a colleagues installation with mine revealed no different settings. So this is how the Property Pages/Configuration Properties/VC++ Directories look like: Executable Directories: $(ExecutablePath) Include Directories: $(IncludePath) Reference Directories: $(ReferencePath) Library Directories: $(LibraryPath) Source Directories: $(SourcePath) Exclude Directories: $(ExcludePath) From the Visual Studio 2010 Command Prompt, cl.exe is found. I can only guess that this behavior was caused by a reinstallation of Studio a couple of months ago (to a different folder). As we use an external build-script for our main project there is a good chance that it is broken since then. Any hints?

  Read the article

• Why is lighttpd and fastcgi keeping sending me the *.scgi file instead of the website content?

  - by e-satis

  I have the following config: server.modules = ( "mod_compress", "mod_access", "mod_alias", "mod_rewrite", "mod_redirect", "mod_secdownload", "mod_h264_streaming", "mod_flv_streaming", "mod_accesslog", "mod_auth", "mod_status", "mod_expire", "mod_fastcgi" ) [...] fastcgi.server = ( ".php" => (( "bin-path" => "/usr/bin/php-cgi", "socket" => "/var/tmp/lighttpd/php-fastcgi.socket" + var.PID, "max-procs" => 1, "kill-signal" => 9, "idle-timeout" => 10, "bin-environment" => ( "PHP_FCGI_CHILDREN" => "200", "PHP_FCGI_MAX_REQUESTS" => "1000" ), "/pyapps/essai/blondes.fcgi" => ( "main" => ( "socket" => "/var/tmp/lighttpd/django-fastcgi.socket", ), ), "bin-copy-environment" => ( "PATH", "SHELL", "USER" ), "broken-scriptfilename" => "enable" ))) [...] $HTTP["host"] =~ "(^|www\.)cam\.com(\:[0-9]*)?$" { server.document-root = "/home/cam/web/" accesslog.filename = "/home/cam/log/access.log" server.errorlog = "/home/cam/log/error.log" server.follow-symlink = "enable" # files to check for if .../ is requested server.indexfiles = ( "index.php", "index.html", "index.htm", "index.rb") url.rewrite = ( "^(/blondes/.*)$" => "/pyapps/essai/blondes.fcgi$1" ) } I have the following dir tree: /home/tv/web/ `-- pyapps `-- essai `-- __init__.py `-- blondes.fcgi `-- blondes.pid `-- django-fcgi.py `-- manage.py `-- manage.pyo `-- plop `-- settings.py `-- urls.py No error when restarting lighthttpd. The I run: ./manage.py runfcgi method=prefork socket=/var/tmp/lighttpd/django-fastcgi.socket daemonize=false pidfile=blondes.pid No errors neither. I then go to http://cam.com/blondes/. I offers me to download an empty file. I checked permissions but everything is set to the same user and group, and they work for the PHP site. The file /var/tmp/lighttpd/django-fastcgi.socket exists. When I reload the page, I got no output in error logs, nor in the manage.py runfcgi command. I probably missed something obvious, but what ?

  Read the article

• Google account gives ERR_SSL_BAD_RECORD_MAC_ALERT errors

  - by Kjensen

  A couple of days ago, I started being unable to connect to accounts.google.com, which handles logins to all kinds of google services. I get this error in Chrome: Error 126 (net::ERR_SSL_BAD_RECORD_MAC_ALERT): Unknown error. In IE I get this: I assume it is the same error, just wrapped up. I run Win8 RTM. On the SAME machine, using the same network card, in a VMWare workstation image running Win7, I am able to connect perfectly. On another of my machines on my network, I am also still able to connect with no problem. My girlfriend uses the same network and has also complained a couple of times about this error (google calendar) - but this is anecdotal, since her technical troubleshooting abilities stop at "xxxx is broken". Her machine runs Win7. ;) I have rebooted, cleared cookies, do not run any antivirus/firewall, have not changed network config. The first 3-4 days after installing Win8, I did not have any problems. I have also searched, and found a hint about enabling SSL2.0 in connection settings, which did not help. Anybody know something about this error and what I can do to fix it?

  Read the article

• Can't access one directory via HTTPS + public FQDN

  - by Justin James

  Hello - I have the strangest IIS error that I've ever seen in my life. I have an application/directory on an IIS server, that throws an error 500 when accessing ANY of the content in it, including HTML documents, when accessed via HTTPS AND the machines FQDN. When I access it with "localhost" it works fine. When I added a bogus entry for the NIC's IP in the hosts file, it worked fine. When I access it with the machines name and HTTP it works fine. Here's a chart (the machine's name is "lofn.titaniumcrowbar.com"): http - lofn.titaniumcrowbar.com: works https - lofn.titaniumcrowbar.com: broken https - localhost: works https - temp.titaniumcrowbar.com (put into hosts file): works I set up tracing, and I got some useless information: "The I/O operation has been aborted because of either a thread exit or an application request. (0x800703e3)" This would make sense, except this happens when pulling up static content. While the directory may be an "application", the content is all static in it. Any/all suggestions, no matter how strange, are VERY appreciated. Thanks! J.Ja

  Read the article

• Write permissions on uploaded files - PHP & Linux

  - by letseatfood

  I am working on a PHP script that transfers files using FTP functions. It has always worked on my production server (which is a hosting service). The development server I have just setup (I am a novice to servers) is Debian Lenny with Apache2, PHP5, and MySQL5. The file transfer works correctly, but once the file has been written to the server, it has permissions of 600. This makes it impossible for me to view the file (JPEG) in the web browser, as permission is denied. I have scoured the internet and even broken my server installation and reinstalled it trying to figure this out (which has been fun, nonetheless!). I know it is unwise to set 777 permissions on public accessible files, but even that will not solve the problem. The only thing that works is if I chmod 777 thefile.jpg after it has been transferred, which is not a working solution. I tried changing the owner of my site files to www-data per this post, but that also does not work. My user is mike, and it still does not work whether the owner of the files is mike or root. Would somebody point me in the right direction? Thanks! And, of course, let me know if I can clarify anything.

  Read the article

• Write permissions LAMP (Debian Lenny)

  - by letseatfood

  I am working on a PHP script that transfers files using FTP functions. It has always worked on my production server (which is a hosting service). The development server I have just setup (I am a novice to servers) is Debian Lenny with Apache2, PHP5, and MySQL5. The file transfer works correctly, but once the file has been written to the server, it has permissions of 600. This makes it impossible for me to view the file (JPEG) in the web browser, as permission is denied. I have scoured the internet and even broken my server installation and reinstalled it trying to figure this out (which has been fun, nonetheless!). I know it is unwise to set 777 permissions on public accessible files, but even that will not solve the problem. The only thing that works is if I chmod 777 thefile.jpg after it has been transferred, which is not a working solution. I tried changing the owner of my site files to www-data per this post, but that also does not work. My user is mike, and it still does not work whether the owner of the files is mike or root. Would somebody point me in the right direction? Thanks! And, of course, let me know if I can clarify anything.

  Read the article

• Host name change breaking http? Fedora

  - by Dave

  OK so I have been messing around on my development server. It has been a while since I have had my head in linux and I suspect I have broken something. I have SSH running and that is working fine. I also have HTTP and I had FTP running also. Earlier today I decided I wanted to rename the machine so I updated the /etc/hosts file and /etc/sysconfig/network. I also changed the server name in the httpd.conf. I rebooted the machine and reconnected to SSH fine. Later I was messing around with the FTP service (trying to tighten up the user security) and when i tried to connect remotely to FTP no joy, it said cannot connect. I thought that was weird but had planned to remove ftp as we will be using github so removed ftp and moved on. Then I tried to connect to the website but major fail. even connecting to the IP address is failing. I used lynx to connect to the localhost and there was my site so something going on at server level. I thought maybe something up with iptables but I have not changed them but tried adding http but still no joy. I have a - Fedora release 17 (Beefy Miracle) NAME=Fedora VERSION="17 (Beefy Miracle)" ID=fedora VERSION_ID=17 PRETTY_NAME="Fedora 17 (Beefy Miracle)" ANSI_COLOR="0;34" CPE_NAME="cpe:/o:fedoraproject:fedora:17" Fedora release 17 (Beefy Miracle) Fedora release 17 (Beefy Miracle) Linux version 3.3.4-5.fc17.x86_64 ([email protected]) (gcc version 4.7.0 20120504 (Red Hat 4.7.0-4) (GCC) ) #1 SMP Mon May 7 17:29:34 UTC 2012 This is my iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT icmp -- anywhere anywhere ACCEPT all -- anywhere anywhere ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:ssh REJECT all -- anywhere anywhere reject-with icmp-host-prohibited Chain FORWARD (policy ACCEPT) target prot opt source destination REJECT all -- anywhere anywhere reject-with icmp-host-prohibited Chain OUTPUT (policy ACCEPT) target prot opt source destination Like I say I can use SSH no issue but http although running is a no go from a remote computer. Any ideas?

  Read the article

• MicroSD card getting corrupted for no good reason

  - by ChaosR

  I recently bought an MicroSD card online. It's a Sandisk 16GB class 2. However, it has a nasty problem. Every time I fill it with my data, the fat tables get corrupted. I've tried reformatting it, blanking it, doesn't seem to solve the problem. I have tried windows and linux (ubuntu), both have the problem. I've used my usb microsd readers, and even tried putting it in my phone and putting data on it from there. All have this problem. Now the really odd thing is, besides the corrupted file tables, no programs can find anything wrong with the hardware. I've tried both chkdisk and "badblocks -w", neither give any type of error. Now I don't know if the actual data gets corrupted, or if its just filesystem tables. What happens is that one or more folders start showing a load of chinese-charred (random UTF8 symbols I suppose) folders and files, and it is impossible to do anything with those. All the other data (outside of the corrupted folders) seems fine. I've tried to test it, and the problem doesn't seem to show up until I fill the disk upto about 3~4GB. After that I can still access the data. But as soon as I eject/safely remove/unmount it, the bad things happen somehow. Next time I plug it in, the folders I most recently wrote to (but sometimes also the folders I wrote the time before last time to) are all gibberish. Does anybody have any clue what might be going on here? EDIT: It seems I can't even put ext3 or ext4 on it, they both complain about a corrupted journal. Gheh, guess something is really broken here.

  Read the article

• Cheap Solution for Routing a Toll Free Number to a Standard POTS Number

  - by VxJasonxV

  I do some technical work for an Internet Radio Show/Podcast, and need to fix something that has been broken for a while. The hosts have a Skype-In number to take listener calls, and for convenience sake, I bought and paid for a toll free number for a period of time. I used to use Asterlink for routing calls, but they folded and sent my number to OneBox, but they're ridiculously expensive by comparison. I'm looking for a cheap solution for this one simple task. Forward toll free calls to a skype-in number. The definition of cheap is as cheap or cheaper than Asterlink was. I paid something like $2 a month, and then the termination/call rate, which was a fraction of a sent for termination, and only whole cents after some serious time on the call. A $20 preload lasted me months at a time. I don't want to be upsold too, I want a simple web based management screen (CDR/stats are fun!), and obviously, it needs to be reliable. What vendors out there are you a fan of that solves this need?

  Read the article

< Previous Page | 117 118 119 120 121 122 123 124 125 126 127 128  | Next Page >