Search Results

Search found 9773 results on 391 pages for 'networking and sharing'.

Page 122/391 | < Previous Page | 118 119 120 121 122 123 124 125 126 127 128 129  | Next Page >

• Can't ping devices by IP address for devices allocated IPs by DHCP

  - by GiddyUpHorsey

  I have a home network with a Trendnet wireless router and a Windows Domain. The Domain Controller/DNS server is a Windows 2000 Server and is configured to forward queries to DNS servers provided by the ISP. The router provides DHCP and is configured with the Windows 2000 Server as the DNS server. The network has been set up for a couple of years and usually works fine. When I connect iPhones to the network over WiFi, the router can ping the iPhones through its browser based admin interface, but Windows machines that are part of the Windows Domain cannot. A laptop was connected to the network over WiFi that wasn't joined to the domain and it could see the iPhones. The router UI shows that the laptop has a reserved IP allocated via DHCP. All machines either have a static or DHCP allocated IP on the 192.168.0.* subnet. Router - 192.168.0.1 - Static - Wired Windows Domain Controller - 192.168.0.8 - Static - Virtual Windows 7 Workstation - 192.168.0.200 - DHCP Auto - Wired VMWare ESXi Host - 192.168.0.201 - Static? - Wired iPhone 1 - 192.168.0.202 - DHCP Auto - WiFi iPhone 2 - 192.168.0.203 - DHCP Auto - WiFi Windows Vista Laptop - 192.168.0.204 - DHCP Reserved - WiFi Using the Windows 7 machine (200), I try to ping each machine and the only DHCP machine that responds is itself. The other DHCP machines fail with Reply from 192.168.0.200: Destination host unreachable.. Using nslookup fails with *** domain.controller.name can't find 192.168.0.203: Non-existent domain. Using the Windows 2000 Domain Controller (8), I try to ping each machine and the only DHCP machine that responds is the Windows 7 machine (200). Pinging the other DHCP machines fails with Request timed out.. Using nslookup also fails with *** domain.controller.name can't find 192.168.0.203: Non-existent domain. Using the iPhone 2 (203), I try to ping (Network Ping Lite) the machines with static IP addresses and that works fine. When I try to ping the Windows 7 machine (200) it is unable to get a response. How do I configure the DNS server/Windows Domain/Router properly so that the Windows Domain machines can see the IPs allocated via DHCP?

  Read the article

• No option to connect to wireless network

  - by Casebash

  I don't have any option to connect to wireless. It just doesn't appear in the taskbar at all - even the no wireless networks were found doesn't appear. In network connections, I only have the option of using a wired connection. According to device manager, I have a working VIA Rhine II Fast Ethernet Adapter (this device only appeared after I selected showing hidden devices). I have already attempted restarting the computer a few times. Does anyone have any suggestions?

  Read the article

• How to configure a wireless router to point to a remote www proxy

  - by Mark

  I have a LG smart Tv with browser. I need the tv browser to connect to a uk based proxy server on port 808. Unfortunately there is no option within tv to setup proxy for its browser. Now the Tv connects via a wireless connection to the internet. IE: TV <- D-Link DIR-605L <- ADSL <- WWW. Is it possible to setup this wireless router to connect the TV to the Proxy ?? If so ? where ? and what setings do i need to change in the wireless router ?? In short my question is ? How do i get the wireless router to make up for the lack of proxy connectivity within my Tv browser ?? Thanks in advance NB: I have configured my Pc's browser's proxy settings, and streaming via the proxy works 100%

  Read the article

• Window 7 image in vmware will allow network connection out but not http

  - by Ormis

  I am currently trying to create a set of images to deploy on my network, but I've run in to a snag. When I create my own Windows 7 image I can successfully use NAT for connecting to the network but whenever I try to access a webpage I get nothing. To be more specific, All firewalls/iptables are disabled on my host machine, my virtual machine, and my network. I can do lookups and all addresses respond correctly (i'm even using Google's DNS). On the host OS i have full connectivity. On the virtual machine I can ping any device I want and all addresses resolve correctly. Within a browser I cannot reach any page via hostname or IP. I feel almost like port 80 is being blocked but i can't find any reason this would be the case. If anyone has had this occur before, I would love some insight to the problem. I understand this question is a bit out of the norm for stackoverflow, but I've run out of ideas. Thank you for any help you can provide.

  Read the article

• Can I set up multiple accounts on DD-WRT? [closed]

  - by Greg Ros

  Possible Duplicate: Can I set up multiple accounts on DD-WRT? I want to set up multiple accounts on DD-WRT (accounts meaning, username-password pairs). Specifically, I want one to be used primarily for remote web management (though there is no reason to restrict the account to such). Is this possible? If so, how do I go about it? I'm running: Router Model TP-Link TL-WR1043ND Firmware Version DD-WRT v24-sp2 (08/07/10) std - build 14896

  Read the article

• VPN Network intermittantly fails to provide internet: What could be possible causes

  - by Jake M

  We have a small office with our own VPN setup. We occasionally experience failures in our internet connection where we cannot access the internet. Most of the time the internet connection will resume by itself(without me doing anything) after a period of time(10 mins). Would you be able to suggest possible causes of the connection failure so I can then go and run some tests? Our network architecture is like so: A 'Billion' brand router that is connected to the internet via phone cable and then connected to our Cisco Switch A Cisco Switch/Bus which is connected to all our office nodes, our external harddrive and also to our router as stated above. All connections are via ethernet cable A series of work computers(nodes) connected via ethernet cable to the Cisco switch. Our ISP is TPG Australia We have a Virtual Private Network All the ethernet cables are about 3 years old Do you think that the causes of our intermittant connection problems could be due to the following: Data collisions in the ethernet cables Old/Faulty ethernet cables Our ISP has bad service Can you think of any other causes of the problem?

  Read the article

• Does a router have a receiving range?

  - by Aadit M Shah

  So my dad bought a TP-Link router (Model No. TL-WA7510N) which apparently has a transmitting range of 1km; and he believes that it also has a receiving range of 1km. So he's arguing with me that the router (which is a trans-receiver) can communicate with any device in the range of 1km whether or not that device has a transmitting range of 1km. To put it graphically: +----+ 1km +----+ | |------------------------------------------------->| | | TR | | TR | | | <----| | +----+ 100m+----+ So here's the problem: The two devices are 1km apart. The first device has a transmitting range of 1km. The second device only has a transmitting range of 100m. According to my dad the two devices can talk to each other. He says that the first device has a transmitting and a receiving range of 1km which means that it can both send data to devices 1km away and receive data from devices 1km away. To me this makes no sense. If the second device can only send data to devices 100m away then how can the first device catch the transmission? He further argues that for bidirectional communication both the sender and the reciver should have overlapping areas of transmission: According to him if two devices have an overlapping area of transmission then they can communicate. Here neither device has enough transmission power to reach the other. However they have enough receiving power to capture the transmission. Obviously this makes absolutely no sense to me. How can a device sense a transmission which hasn't even reached it yet and go out, capture it and bring it back it. To me a trans-receiver only has a transmission power. It has zero receiving power. Hence for two devices to be able to communicate bidirectionally, the diagram should look like: Hence, from my point of view, both the devices should have a transmission range far enough to reach the other for bidirectional communication to be possible; but no matter how much I try to explain to my dad he adamantly disagrees. So, to put an end to this debate once and for all, who is correct? Is there even such a thing as a receiving range? Can a device fetch a transmission that would otherwise never reach it? I would like a canonical answer on this.

  Read the article

• Sonicwall 3500 (Creating VLANS for usage of multiple SSID)

  - by Thomas Chia

  I have an issue here. Here is my setup: X0 - STAFF network | X2 - AGENT network | X4 - Wireless AP (for multiple SSID) Okay, basically I'm going to set up the wireless AP to be broadcasting 2 SSID, STAFF-WIFI and AGENT WIFI. When connected to STAFF-WIFI, the users will be connected to the STAFF network, while connected to the AGENT WIFI, the users will be connected to the AGENT network. Can someone explain in details how to go about setting up this configuration? Thanks!

  Read the article

• Failed to mount to nfs server with "Program not Registered"

  - by Farrel

  I'm trying to setup nfs server on Fedora 17 and I'm getting "Program not Registered" error when I'm trying to mount. I guess the main reason for this is rpcbind. I'm a newbie in linux, so I don't know what info should I provide you with. Here is some info that might be useful. rpcinfo -p program vers proto port service 100000 4 tcp 111 portmapper 100000 3 tcp 111 portmapper 100000 2 tcp 111 portmapper 100000 4 udp 111 portmapper 100000 3 udp 111 portmapper 100000 2 udp 111 portmapper 100005 1 udp 20048 mountd 100005 1 tcp 20048 mountd 100005 2 udp 20048 mountd 100005 2 tcp 20048 mountd 100005 3 udp 20048 mountd 100005 3 tcp 20048 mountd 100024 1 udp 42223 status 100024 1 tcp 50054 status cat /etc/exports /home/Farrel/prog 192.168.xxx.xxx (ro,sync) service nfs status Redirecting to /bin/systemctl status nfs.service nfs-server.service - NFS Server Loaded: loaded (/usr/lib/systemd/system/nfs-server.service; enabled) Active: active (exited) since Fri, 02 Nov 2012 09:29:04 +0300; 5min ago Process: 924 ExecStartPost=/usr/lib/nfs-utils/scripts/nfs-server.postconfig (code=exited, status=0/SUCCESS) Process: 909 ExecStart=/usr/sbin/rpc.nfsd $RPCNFSDARGS ${RPCNFSDCOUNT} (code=exited, status=0/SUCCESS) Process: 885 ExecStartPre=/usr/sbin/exportfs -r (code=exited, status=0/SUCCESS) Process: 864 ExecStartPre=/usr/lib/nfs-utils/scripts/nfs-server.preconfig (code=exited, status=0/SUCCESS) CGroup: name=systemd:/system/nfs-server.service Warning: Journal has been rotated since unit was started. Log output is incomplete or unavailable. Firewall is disabled on both systems. I spent a lot of time reading on the topic but all manuals on setting up nfs server lead to "Program not Registered" error. Any how-to-fix-it ideas?

  Read the article

• Troubleshooting an unstable internet connection

  - by Konrad Rudolph

  My MacBook Pro running OS X (10.9, but I had the same problem before) is connected to a Belkin router via WiFi and, using Virgin Media as the ISP, to the internet. The connection is extremely unstable – on some days, I get a ping timeout every few seconds. In addition, some domains seem to suffer general connectivity issues. For instance, I often find that while the youtube.com website loads, none of the videos (which are hosted on a separate domain) do. At other times, videos load but always fail to buffer, even though the actual connection speed is ok, even though I’ve disabled dash playback. Since I’m living in a rented room and the ISP contract isn’t actually mine I’ve got only limited possibilities of addressing the problem. In particular, I have no access to the router configuration and my non tech savvy landlady, while sympathetic, is not in a great hurry to hand the problem over to the ISP’s customer support. What’s more, I seem to be the only person in the house experiencing these problems – but I can imagine that this is simply because I’m the only one who’s using the internet continuously. I’m searching for specific tests that might be able to pinpoint – and ideally solve – the problem. So far all I’ve managed to do is establish that Virgin is routing my traffic in mysterious ways. Here’s an excerpt from traceroute google.co.uk. It’s worth mentioning that the host name doesn’t seem to matter a lot, the trace route is always the same. traceroute: Warning: google.co.uk has multiple addresses; using 62.254.36.148 traceroute to google.co.uk (62.254.36.148), 64 hops max, 52 byte packets 1 (192.168.2.1) 1.112 ms 1.300 ms 2.359 ms 2 10.100.32.1 (10.100.32.1) 11.926 ms 10.217 ms 24.987 ms 3 cmbg-core-1a-ae3-610.network.virginmedia.net (80.1.202.93) 28.809 ms * 66.653 ms 4 popl-bb-1b-ae16-0.network.virginmedia.net (212.43.163.141) 13.759 ms 126.504 ms 20.472 ms 5 nrth-bb-1b-et-010-0.network.virginmedia.net (62.253.175.57) 28.357 ms 16.398 ms 42.387 ms 6 nrth-bb-1c-ae1-0.network.virginmedia.net (62.253.174.110) 27.441 ms 15.622 ms 12.044 ms 7 lutn-icdn-1-ae0-0.network.virginmedia.net (62.253.175.82) 16.678 ms 28.463 ms 28.253 ms 8 * * * 9 * * * 10 * * * ^C If I let it, this goes on until the end of time. It never seems to reach a destination. Is this normal? A friend living in the same town who is also with Virgin Media has a more conventional traceroute output: 7 hops to google.co.uk, all of which send the ICMP TIME_EXCEEDED response. The obvious fix – rebooting the router – doesn’t seem to help. As far as I can tell, the WiFi connection is stable (I can always ping the router) so the problem is further downstream. I’ve tried using an alternative DNS before (OpenDNS) but if anything, this made things worse. In fact, it made all Google services nigh unreachable.

  Read the article

• Cloudstack virtual machines can't communicate with virtual routers when they are on different hosts

  - by Jorge Suárez de Lis

  I'm using Cloudstack 2.2.14 on a Ubuntu 10.04 set of hosts, and I have a problem on my setup. I have two hosts running. When a virtual router is created on host 1 and a virtual machine using that virtual router is created on host 2, or vice versa, I have no connectivity at all on the virtual machine. First of all, I have to setup the network manually on that virtual machine -usually DHCP is working, but not here-. Then, I can't ping to the virtual router from the virtual machine or vice versa. When both virtual router and virtual machine are created on the same host, everything works! Maybe those packages are being filtered somehow? I have no clue on how to proceed. Both hosts can communicate directly outside the virtualization.

  Read the article

• How can I get my routers to forward ports correctly?

  - by Giffyguy

  My network currently looks like this (simplified): Note that Router #2 is connected to the LAN interface of Router #1. This should be familiar to anyone who has seen a standard static-IP setup with an additional firewall for a residence or other small building. Router #1 is actually my cable gateway, but since it is a fully functional router/firewall, I am going to refer to it as a router. Now, I need to open various ports in both firewalls for incoming communication to my server - port 80 is a good example. So I've opened up port 80 in Router #2, and so far all incoming traffic at the public IP X.X.X.129 is being routed correctly. The problem is that I also need my server to respond to incoming traffic at the public IP X.X.X.130 on the WAN interface of Router #1. Naturally, I can't just tell Router #1 to forward port 80 to another public IP. Port forwarding is only supported when the traffic is being directed to the LAN subnet. I am willing to restructure my network topology if required, with the following conditions: Router #1 cannot have its WAN IP reassigned - X.X.X.130 is mandatory. Router #1 cannot be moved or disconnected from the cloud. The server cannot be given a second IP address. I would prefer the server to have a private IP address - e.g. 10.0.0.10 I'd like to keep Router #2, but it can have a private IP - e.g. 10.0.1.10 Following these rules, I need to get my server to receive incoming traffic on port 80 from both public IP addresses. Does anyone on SU know if this is possible? So far my only theories have been to set up a static route on either router, or to somehow combine my two subnets into a single subnet.

  Read the article

• How to calculate CIDR notation from entries in a routing table

  - by febreezey

  I have some entries in a routing table that were created using longest prefix matching, and I have to use those entries to determine the a.b.c.d/x notation (CIDR). This is an example entry: 11001000 00010111 00010. That was calculated from the range 11001000 00010111 00010000 00000000 through 11001000 00010111 00010111 11111111. I know the range is from IP addresses 200.23.16.0 to 200.23.23.255, but getting the /x for the subnet # doesn't make sense to me. Anyone know how to properly go about calculating it?

  Read the article

• MikroTik ipv6 Tunnel

  - by MikeSmitty

  I've got a MikroTik router set up with the latest stable OS on it, and I just set up an ipv6 tunnel with Hurricane Electric, but I'm having an odd issue with it. I can't ping anything until I first ping the tunnel endpoint on HE's side. After that I can ping any ipv6 address fine, but give it a little time (say, maybe 30 sec) and I can't ping any ipv6 addresses again. Whenever it stops allowing ping to go through I notice the counter on my firewall rule that drops invalid connections goes up. this is my ipv6 firewall config: add action=accept chain=input comment="" connection-state=established \ disabled=no in-interface=sit1 add action=accept chain=input comment="" connection-state=related disabled=no \ in-interface=sit1 add action=accept chain=input comment="" disabled=no in-interface=bridge \ src-address=ipv6_address_here/64 add action=drop chain=input comment="" connection-state=invalid disabled=no \ in-interface=sit1 add action=drop chain=input comment="" disabled=no in-interface=sit1 Any ideas on what it could be?

  Read the article

• What is the equivalent of 127.255.255.255 for OS/X machines so I can test broadcast udp packets without a network?

  - by JohnPristine

  I am trying to test my program that makes use of broadcast UDP (not multicast!). In Linux, I can use the 127.255.255.255:64651 address and everything works beautifully, in other words, I send a packet to 127.255.255.255:64651 and multiple clients listening on that port get the packet. A real broadcast example! Unfortunately on my OS/X machine (Mountain Lion) the same example does not work. Is there any way I can get 127.255.255.255 to work on mac machines? Any other solution to get broadcast working on my mac machine without a network? Note: It has to be broadcast, not multicast.

  Read the article

• Does HP 8530w support Wifi 802.11n?

  - by FoxyBOA

  According to vendor site HP 8530w supports 802.11n draft mode. My Windows 7 tell me that network card is 5100 ABG and know nothing about N mode (guys from Intel forum mentioned, that 802.11N versions must ended with N letter, e.g. 5100 ABN). Not sure if it matter, but my laptop model id is #FU462EA. How could I check that my Wifi card compliant with 802.11n (I suspect that "draft N" could have two "special" meaning: doesn't work with 802.11n at all or requires special activation of the mode). Any hints are welcome.

  Read the article

• Top ten security tips for non-technical users

  - by Justin

  I'm giving a presentation later this week to the staff at the company where I work. The goal of the presentation is to serve as a refresher/remidner of good practices that can help keep our network secure. The audience is made up of both programmers and non-technical staff, so the presentation is geared for non-technical users. I want part of this presentation to be a top list of "tips". The list needs to be short (to encourage memory) and be specific and relevant to the user. I have the following five items so far: Never open an attachment you didn't expect Only download software from a trusted source, like download.com Do not distribute passwords when requested via phone or email Be wary of social engineering Do not store sensitive data on an FTP server Some clarifications: This is for our work network These need to be "best practices" tips for the end-user, not IT policy We have backups, OS patches, firewall, AV, etc, all centrally managed This is for a small business (less than 25 people) I have two questions: Do you suggest any additional items? Do you suggest any changes to existing items?

  Read the article

• Problem with Lenovo x200s Wifi under Ubutu Karmic

  - by oneself

  Hi, I have just gotten my Lenovo X200s laptop, and I am install Ubuntu 9.10 Karmic on it. The installation went through without a hitch, but I can't get my wifi to work. lspci | grep Network Produces the following results: 00:19.0 Ethernet controller: Intel Corporation 82567LM Gigabit Network Connection (rev 03) 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8172 (rev 10) The weird part is that when I turn the wifi hardware stitch on and off on the side of the laptop, I get the following printed in /var/log messages: Dec 30 23:24:48 temp-laptop kernel: [ 213.432302] usb 4-2: USB disconnect, address 2 Dec 30 23:24:52 temp-laptop kernel: [ 217.276310] usb 4-2: new full speed USB device using uhci_hcd and address 3 Dec 30 23:24:52 temp-laptop kernel: [ 217.441759] usb 4-2: configuration #1 chosen from 1 choice Does Ubuntu think my wifi card is a USB device? Am I missing some driver? What can I do to fix this? Please, help!

  Read the article

• Having trouble setting up my router

  - by indyK1ng

  I just moved into my apartment and the Internet connection is working. It's Comcast in case that matters. Anyway, I'm having trouble setting up my wireless router (Netgear WNR2000) to work with it. Are there any settings that I could be missing? I currently have it set up to use a static IP address and I found the DNS servers I'm supposed to use and the Internet light is green, but I can't get out to the Internet. When I am trying, I'm connecting to an Ethernet port on the back of my router. Is there a setting I'm missing or a setting that I have set wrong? I used the automatic set up wizard to learn that it's a static IP address. Any help would be appreciated. I am currently only able to use my Linux machine, so please make any help in Linux commands. Yes, I can connect to the Internet if I connect to the modem directly and I've been using the web interface when I'm connected to the router, so I suppose I can ping the router. My router detected the connection as using a static IP address, so I connected to the modem directly and figured out what my IP address, gateway, and mask were as well as DNS servers.

  Read the article

• What keeps you from changing your public IP address and wreak havok?

  - by Whitemage

  An interesting question was asked to me and I did not know what to answer.. So I'll ask here. Let's say I subscribed to an ISP and I'm using cable internet access. ISP gives me a public IP address of 60.61.62.63. What keeps me from changing this IP address to, let's say, 60.61.62.75 and mess with another consumer's internet access? For the sake of this argument, let's say that this other IP address is also owned by the same ISP. Also, let's assume that it's possible for me to go into the cable modem settings and manually change the IP address. Under a business contract where you are allocated static addresses, you are also assigned a default gaetway, a network address and a broadcast address. So that's 3 addresses the ISP "loses" to you. That seems very wastefull for dynamically assigned IP addresses where the majority of customers are.. Could they simply be using static arps? ACLs? Other simple mechanisms? Anyone who worked at an ISP would be willing to explain this a bit?

  Read the article

• http, https and ftp is not working but smtp and imap is working

  - by Unicron

  hi all, yesterday on a computer of a friend a strange thing happened. after booting the ports fo http, https and ftp are closed but e-mail is still working. in the control panel the windows firewall seems active even if he tries to deactivate it. i have a suspision that it is the faul of norton internet security 2010, we have tried to uninstall it, but the uninstallation did not work. when using the removal tool from symantec it just goes to 23% and then it crashes. the process ccSvcHst.exe is still running. how can i safeley remove the rest of norton internet security? thanks in advance [edit] norton internet security 2010 is sucesfully removed, but still no connectivity

  Read the article

• why would you create two different subnets on the same physical network?

  - by xirtyllo

  I'm working at a messy location, one of the strange (for me) things is that on the same physical network there are two different subnets. Specifically some computers will have 10.0.0.0/24 and some others will have 172.16.0.0/24. There is only one DHCP server, which gives IPs on the 10.0.0.0/24 range, and there are two internet gateways, one with IP 172.16.0.1 and one with IP 10.0.0.1 . To give an example, I can easily swap one PC from one subnet to the other just by changing its IP and gateway settings. I am trying to imagine why they created the network this way, and which may be the possible advantages and/or drawbacks of having two different subnets on the same physical network. Any thoughts?

  Read the article

• How to Set Linux Bonding Interface to Gigabit

  - by Kyle Brandt

  I have enabled Linux active backup mode bonding. Each interface is a gigabit interface, but the bond interface seems to end up at 100 Megabit: bonding: bond0: Warning: failed to get speed and duplex from eth1, assumed to be 100Mb/sec and Full. ... bnx2: eth0 NIC Link is Up, 1000 Mbps full duplex, receive & transmit flow control ON ... bonding: bond0: backup interface eth1 is now up ethtool apparently can't provide info on bond: sudo ethtool bond0 Settings for bond0: No data available So does this mean I am operating at 100 or 1000 Megabit (My guess is 1000)? If it is only 100, what options in the ifcfg scripts or the modprobe bonding options do I need to sett to make it 1000?

  Read the article

• Configure an Azure VM for Dynamic DNS for Cloud Services

  - by Adam

  I am trying to setup an azure VM with proper DNS to allow multiple cloud services to communicate across cloud service boundaries. As I understand it, I need to provide my own DNS server. I do not have any on-premise infrastructure, so I am trying to configure an Azure VM to act as my DNS. This SO question (http://stackoverflow.com/questions/21858926/azure-how-to-connect-one-cloud-service-with-other-in-one-virtual-network) is very similar to my setup. This article (http://msdn.microsoft.com/en-us/library/windowsazure/jj156088.aspx) describes my particular case: Name resolution between virtual machines and role instances located in the same virtual network, but different cloud services Here is what I have done: Created Azure Virtual Network and declared subnets for each of my cloud services. Created an Azure VM (Windows 2012 R2) with DNS enabled RDP to the VM and enabled the DNS role and installed features Added the appropriate NetworkConfiguration xml section to each of my cloud services .csfg files Re-deployed my cloud services I have verified that I setup the virtual network and networkconfiguration properly because my cloud service hosts are able to communicate with each other if I use the internal ips. However, name resolution doesn't appear to be working, and it doesn't appear that my cloud service roles can communicate with my DNS server. How do I configure my VM so that my different cloud services roles register themselves with my DNS server? EDIT: I think I am 1 step closer to getting this to work. The cloud services that I was using are in an old affinity group which is not supported by VMs, so I was unable to add my VM into my virtual network. I created a new VNET in a new affinity group with my VM added into it. However, I still don't know how to configure the azure VM's DNS server so that the cloud services register themselves for name resolution. Also, an added bonus guaranteed to get a +1 would be to explain if it is possible to register a DNS entry for the VIP for an internal endpoint of my cloud services so we can get load balancing. Thanks!

  Read the article

• How to stop a infinite running process(ztail) started by a ssh session after that session is closed

  - by Sanath Adiga

  I have a peculiar problem. My server supports multiple ssh session simultaneously, so that multiple admins can manage it simultaneously. We have a command which calls ztail to show the compressed log files and when the current ssh session is closed (without pressing ctrlc, to stop the tail command), the command should ideally stop working. But what I observed when I start a new ssh session is that the process ztail is still running in the background and consuming CPU, even though the previous session was closed. How can I determine when the session is closed, so that I can use that variable/flag to close/stop any commands initiated by that previously closed session?

  Read the article

< Previous Page | 118 119 120 121 122 123 124 125 126 127 128 129  | Next Page >