Search Results

Search found 4012 results on 161 pages for 'alpha channel'.

Page 124/161 | < Previous Page | 120 121 122 123 124 125 126 127 128 129 130 131  | Next Page >

• VMWare Raw Device Mapping Not Working

  - by George H. Lenzer

  While I'm waiting for VMWare support to get back to me, I thought I'd ask here. I have a 400 gig LUN presented from a fiber channel SAN to my VMWare host. It's legacy from another virtualization platform and I need to keep it as is to avoid a long period of downtime. I formatted my VMFS3 datastore with 4 meg blocks to allow up to 1 TB disks. Then I tried adding my 400 gig disk as a raw device in physical compatibility mode. I get the error: "File is larger than the maximum size supported by datastore 'Base Test'. [Base Test]VMTEST01/VMTEST01_2.vmdk Originally I had the VMFS datastore formatted with 1 meg blocks which was the cause of this problem since the largest disk allowed would be 256 gigs. But I deleted the data store and then reformatted with 4 megs blocks. I've also tried using virtual compatibility mode for the raw device but it still fails. Does anyone have any suggestions? I've been waiting for a little over a week for VMWare, but that's fine because I'm not yet a paying customer. I'm still in the eval phase.

  Read the article

• Too many concurrent connections Exchange 2010. What else is there to check?

  - by hydroparadise

  I thought that I had this under control before. But for some reason during our last email marketing promo, I start receiving from our mass email client (built in house).. The message could not be sent to the SMTP server. The transport error code is 0x800ccc67. The server repsonse was 421 4.3.2 The maximum number of concurrent connections has exceeded a limit, closing transmission channel again. There's several places I've checked to make sure that wouldn't be an issue. First I checked that receive connector was set to receive an adequate number of connections on our relay connector (1000 connections). Then, I would later find out about Throttling Policies. I created one and set all the properties I knew to set in terms of the policy following properties to 1000; EWSMaxConcurrency, OWAMaxConcurrency, CPAMaxConcurrency, and CPAMaxConcurrency. Still, the email client starts receiving the error shortly after 100 has been sent and takes about 15-30 seconds. The process is then repeatable, but still the error gets received at the same spot everytime. Is there a rate setting that I am missing? Was there a windows update that I missed looking at? Should the software have it's own throttling feature?

  Read the article

• Photoshop CS4. How do I make sure my color stays the same in my different .psd files? (could be RGB

  - by Kris

  I asked 2 photoshop experts I know but they haven't got a clue because all my settings are exactly the same, in both files. (except the RGB type !! I'm not sure. Please read on) I use RGB color, 72DPI, 8 bits / channel. No adjustments (filters, like greyscale, etc ...) are selected / used. The layers are both normal, and opacity and fill are 100% (yes, in both files). I took two screenshots, and you can see the difference: http://www.flickr.com/photos/30465871@N05/4623864297/ http://www.flickr.com/photos/30465871@N05/4624469754/ Both colors are ff795d, but that doesn't matter, any color I use gives me the same problem: they both look different. Now, I know the CMYK settings (see screenshots) are different, but when the settings are the same the color changes. Why is this happening and how do I solve this problem? My guess is I'm working with different a type of RGB. It's sRGB IE61966 - 2.1 in the file I created (file info raw data) but I can't find that in the file that started with a screenshot. If that's the problem, how do I change / convert the RGB, once the file is already open? Thank you.

  Read the article

• Windows 7 hangs after going into sleep a second time

  - by Brian Stephenson

  I've searched everywhere around Google and can't figure out why this is happening so I decide to ask here to see if anyone has a problem like this. Like it says in the title, whenever I sleep ONCE I'm able to wake the system, but going back to sleep again AFTER waking up for the first time results in it hanging on no input and no output, with the fan spinning as fast as possible and alot of heat being spewed out by the fan as well. I've tried various things like setting all USB Hub Root's to not get switched off for power saving, disabling USB selective suspend, disabling PCI-e link state power management, and even unplugging ALL USB devices and it wont wake up after the second attempt. And I've even waited up to a full hour of the CPU fan spinning loudly and it's still stuck trying to wake up. The only USB devices I use are a Microsoft USB Comfort Curve Keyboard 2000 (IntelliType Pro) and a generic HID compliant mouse from Creative model number OMC90S "CREATIVE MOUSE OPTICAL LITE". My other devices like external drives and controllers are unplugged when I'm not using them as having too many USB devices plugged in at a time causes a deadlock on almost all of the ports I have. Here's my system specifications (Most of these are from CPU-Z): Brand: Gateway DX4300-19 Mainboard: Gateway RS780 Chipset: AMD 780G Rev 00 Southbridge: AMD SB700 Rev 00 LPCIO: ITE IT8718 BIOS: American Megatrends Inc. ver P01-A4 09/15/2009 CPU: AMD Phenom II X4 810 at 2.60 GHz RAM: 8.0 GB DDR2 Dual Channel Ganged Mode at 400 MHz GPU: ATI Radeon HD3200 Graphics Intergrated - RS780 OS: Windows 7 Home Premium x64 OEM (Acer Group) HDD: WDC WD10EADS-22M2B0 1.0 TB (Western Digital Green Caviar) My BIOS has absolutely no control over how I setup the sleep mode to be either S1 or S3. So I can't check these settings or even change them. Hybrid sleep is also disabled, I can successfully go into hibernation and wake from hibernation but this is painfully slow due to a harddrive problem I'm having with this "Green Drive". (Hibernation takes over ~3 minutes to complete) Any help would be appreciated, thanks.

  Read the article

• Which upgrade path for disk IO bound postgres server?

  - by user41679

  Hi all, We currently have a Sun x4270 with 2xquad core Xeon Nehalmen 2.93ghz cores (16 threads), 72 gig of ram and 16 x 10k SAS disks split between the os raid 1, a partition for the Write Ahead Logs which is raid 10 and a partition for the database tables and indexes which is also raid 10, all xfs. I'm currently evaluating which path to go down in terms of upgrades. We'll be sharding the DB at some point soon, but for now I need to focus on hardware upgrades specifically. The machine is not CPU or memory bound at all at the moment, just IOWait is become an issue. The machine is mostly write access as we have a heavy caching layer. We're seeing about 300 write IOPS average on both the database partitions. We don't have any additional storage infrastructure like a Fiber Channel or ISCSI network. Budget isn't too much of a concern, something inline with the size of this server (i.e no $1m IBM machines) Space is ok on the DB side of things, we're running out obviously but there's also some reduction we can do. Additional space would be good though. My current thoughts are either: * ISCSI SAN, possible with 10Gbit network that has solid state acceleration. * FusionIO card / Sun F20 card (will the FusionIO card work in the Sun box? * DAS shelf (something like this http://www.broadberry.co.uk/das-direct-attached-storage-servers/cyberstore-224s-das) which a combination of 15k sas disks and some Intel X25-E drives for DB indexes etc) what would I need to put in the x4270 to add a DAS shelf? I think it's a SAS HBA card, do I have to use Sun's own card or will any PCI Express card work? Anything else??? what would you guys do from your experience? I appreciate it's a lot of questions, but I haven't expanded a DB machine for a number of years and the landscape has changed dramatically since then! Any advice or feedback would be very much appreciated. Let me know if there's anything else I can clarify. Thanks in advance!

  Read the article

• nginx: dump HTTP requests for debugging

  - by Alexander Gladysh

  Ubuntu 10.04.2 nginx 0.7.65 I see some weird HTTP requests coming to my nginx server. To better understand what is going on, I want to dump whole HTTP request data for such queries. (I.e. dump all request headers and body somewhere I can read them.) Can I do this with nginx? Alternatively, is there some HTTP server that allows me to do this out of the box, to which I can proxy these requests by the means of nginx? Update: Note that this box has a bunch of normal traffic, and I would like to avoid capturing all of it on low level (say, with tcpdump) and filtering it out later. I think it would be much easier to filter good traffic first in a rewrite rule (fortunately I can write one quite easily in this case), and then deal with bogus traffic only. And I do not want to channel bogus traffic to another box just to be able to capture it there with tcpdump. Update 2: To give a bit more details, bogus request have parameter named (say) foo in their GET query (the value of the parameter can differ). Good requests are guaranteed not to have this parameter ever. If I can filter by this in tcpdump or ngrep somehow — no problem, I'll use these.

  Read the article

• What is the peak theoretical WiFi G user density? [closed]

  - by Bigbio2002

  I've seen a few WiFi capacity planning questions, and this one is related, but hopefully different enough not to be closed. Also, this is related specifically to 802.11g, but a similar question could be made for N. In order to squeeze more WiFi users into a space, the transmit power on the APs need to be reduced and the APs squeezed closer together. My question is, how far can you practically take this before the network becomes unusable? There will come a point where the transmit power is so weak that nobody will actually be able to pick up a connection, or be constantly roaming to/from APs spaced a few feet apart as they walk around. There are also only 3 available channels to use as well, which is a factor to consider. After determining the peak AP density, then multiply by users-per-AP, which should be easier to find out. After factoring all of this in and running some back-of-the-envelope calculations, I'd like to be able to get a figure of "XX users per 10ft^2" or something. This can be considered the physical limit of WiFi, and will keep people from asking about getting 3,000 people in a ballroom conference on WiFi. Can anyone with WiFi experience chime in, or better yet, provide some calculations for a more accurate figure? Assumptions: Let's assume an ideal environment with no reflection (think of a big, square, open room, with the APs spaced out on a plane), APs are placed on the ceiling so humans won't absorb the waves, and the only interference are from the APs themselves and the devices. As for what devices specifically, that's irrelevant for the first point of the question (AP density, so only channel and transmit power should matter). User experience: Wikipedia states that Wireless G has about 22Mbps maximum effective throughput, or about 2.75MB/s. For the purpose of this question, anything below 100KB/s per user can be deemed to be a poor user experience. As for roaming, I'll assume the user is standing in the same place, so hopefully that will be a non-issue.

  Read the article

• Slowdown upon router/modem setup change

  - by Ollie Saunders

  I’ve been using a Belkin FSD7632-4 modem router to connect to my TalkTalk provided ADSL internet connection for some time and been pretty happy with it. Recently, however, the connection has been failing and I decided to get a ASUS RT-N16 instead, which is also a much more capable router generally. The ASUS RT-N16 doesn’t come with a modem built-in so I purchased as Zoom modem as well. I’ve set them both up and am using them to post this message. But I’m a bit miffed to find that I get a significantly and consistently slower downstream rate from the new configuration than with the old Belkin. Belkin modem router: downstream: 3.45 mbps upstream: 0.73 mbps ASUS router + Zoom modem: downstream: 2.71 mbps upstream: 0.66 mbps Any ideas why this is? The really weird thing about this is that the Zoom supports ADSL2 and ADSL2+ but I don’t think the old Belkin does. At first I thought it might be due to the Zoom modem being limited to PPPoE instead of PPPoA, which my ISP supports, but then I tried using PPPoE with the Belkin and that still gave a high speed. I’m using VC-Mux encapsulation with both. VPI of 0 and VCI of 38. I pulled this data off the Zoom: Mode: ADSL2 Line Coding: Trellis On Status: No Defect Link Power State: L0 Downstream Upstream SNR Margin (dB): 12.3 11.8 Attenuation (dB): 43.0 24.9 Output Power (dBm): 12.9 0.0 Attainable Rate (Kbps): 3936 844 Rate (Kbps): 3194 840 MSGc (number of bytes in overhead channel message): 59 10 B (number of bytes in Mux Data Frame): 99 14 M (number of Mux Data Frames in FEC Data Frame): 2 16 T (Mux Data Frames over sync bytes): 1 8 R (number of check bytes in FEC Data Frame): 8 8 S (ratio of FEC over PMD Data Frame length): 1.9833 9.0594 L (number of bits in PMD Data Frame): 839 219 D (interleaver depth): 32 2 Delay (msec): 15 4 Super Frames: 15808 14078 Super Frame Errors: 0 4294967232 RS Words: 513778 111753 RS Correctable Errors: 126 4294967238 RS Uncorrectable Errors: 0 N/A HEC Errors: 0 4294967279 OCD Errors: 0 0 LCD Errors: 0 0 Total Cells: 1920175 237597 Data Cells: 205993 392 Bit Errors: 0 0 Total ES: 0 0 Total SES: 0 0 Total UAS: 34 0

  Read the article

• Computer does not boot after ram upgrade

  - by Calmarius

  I have a Dell Optiplex GX520 desktop (it's abount 5 yr old) PC with 512 MB DDR2 RAM. Since my computer always swapping I thought I should upgrade my RAM. I bought a Kingmax 2GB DDR2 RAM. But my system does not boot. The status leds are on 2 and 4. The user manual says 'video card failure' wtf? I put back the original module and everything works. I tried many combinations. When I leave the old 512 RAM in and put the 2GB next to it to the other socket my system completes the POST and I'm able to enter the BIOS menu. It says my system has 2.5 GB installed, one 0.5GB and one 2GB in dual asymmetric channel mode. It's seemingly right. Exiting the BIOS setup GRUB loads successfully, but when I try to boot Ubuntu it crashes with kernel panic immediately. Trying to load Windows XP does not get past the loading screen, it crashes with 0x8E stop error. Does this mean the ram I bought is faulty? Or is it just mean that the memory module I bought is too new to be handled my computer? I this case I may exchange the RAM with my friends. No other computer is in my house (my very old box has DDR1 ram, my systers new box has DDR3 ones. I can't plug my memory in neither one.) I'm going to return the RAM to store to replace it with a better one tomorrow. Is there any hope to get this new module work?

  Read the article

• How to play WAV file through Network Paging Interface

  - by BGM

  In our building we have a Viking Paging ZPI-4 Interface for our intercom. The interface receives data from our Asterisk Phone system via a Cisco SPA112 Port Adapter which has it's own IP address on the network and converts digital into analog. Asterisk plays the "5" tone and then allows the user's voice to commence over the connection. Now, what I want to do is to play a wav file over this Viking Paging device using the Cisco Port Adapter. I know how to get Asterisk to do it, but I want to do this without Asterisk. I want some kind of program that can talk to the Cisco Port Adapter and then transmit the wav file into the Viking Paging Device. What kind of program do I need to get or make? Now, I found this link if it helps anyone with ideas. I also found this information, but I'm not sure how to apply it. I also found this, but it involves an arduino. However, I already have the analog-to-digital convertor, and the Viking will handle sending sound over the paging speakers. I just need to know how to send the wav file to the Viking via the Port Adapter. So far, I know my wav file should be formatted as 8bit mono, and I need to send the "5" tone to open the Viking Pager's channel. [update] I am trying to figure out if I can use VLC player to stream to the ipaddress of the Port Adapter. So far I'm not having success with that, and don't even know if it will work. Windows Media Player has a streaming option too. I am thinking that since the Cisco Port Adapter thinks it is a sort of phone, that the only way this can be done is via SIP.

  Read the article

• Mac Mavericks, ngircd localhost works, private IP doesn't

  - by user221945

  I have configured ngircd to listen on my private ip address. It doesn't. Localhost works fine. Configuration test: ngIRCd 21-IDENT+IPv6+IRCPLUS+SSL+SYSLOG+TCPWRAP+ZLIB-x86_64/apple/darwin13.2.0 Copyright (c)2001-2013 Alexander Barton () and Contributors. Homepage: http://ngircd.barton.de/ This is free software; see the source for copying conditions. There is NO warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. Reading configuration from "/opt/local/etc/ngircd.conf" ... OK, press enter to see a dump of your server configuration ... [GLOBAL] Name = irc.bellbookandpistol.com AdminInfo1 = Jaedreth AdminInfo2 = San Diego County CA, US AdminEMail = [email protected] HelpFile = /opt/local/share/doc/ngircd/Commands.txt Info = Server Info Text Listen = 10.0.1.5,127.0.0.1 MotdFile = MotdPhrase = "Welcome to irc.bellbookandpistol.com" Password = PidFile = Ports = 6667 ServerGID = wheel ServerUID = root [LIMITS] ConnectRetry = 60 IdleTimeout = 0 MaxConnections = 0 MaxConnectionsIP = 6 MaxJoins = -1 MaxNickLength = 9 MaxListSize = 0 PingTimeout = 120 PongTimeout = 20 [OPTIONS] AllowedChannelTypes = #&+ AllowRemoteOper = no ChrootDir = CloakHost = CloakHostModeX = CloakHostSalt = kBih5mu\kVI!DC6eifT(hd4m/0'zb/=: CloakUserToNick = no ConnectIPv4 = yes ConnectIPv6 = no DefaultUserModes = DNS = yes IncludeDir = /opt/local/etc/ngircd.conf.d MorePrivacy = no NoticeAuth = no OperCanUseMode = no OperChanPAutoOp = yes OperServerMode = no RequireAuthPing = no ScrubCTCP = no SyslogFacility = local5 WebircPassword = [SSL] CertFile = CipherList = HIGH:!aNULL:@STRENGTH DHFile = KeyFile = KeyFilePassword = Ports = [OPERATOR] Name = [REDACTED] Password = [REDACTED] Mask = [CHANNEL] Name = #BBP Modes = tnk Key = MaxUsers = 0 Topic = Welcome to the Bell, Book and Pistol IRC Server! KeyFile = As you can see, it should be listening on 10.0.1.5, but it isn't. After turning on Apache manually, port 80 works on 10.0.1.5, but port 6667 doesn't. It only works on localhost. Is there some terminal command I could use or some config file I could edit to get this to work?

  Read the article

• Wireless does not work on Ubuntu 9.04

  - by Yongwei Xing

  Hi all I install the Ubuntu 9.04 my old Lenovo Y520 laptop, the wirless does not work.My Wireless card is Intel Pro/wireless 2100 card. But I can not enable it. My wired card is working well. Does anyone meet it before. the ifconfig output is eth0 Link encap:Ethernet HWaddr 00:0a:e4:5f:6c:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:973 errors:0 dropped:0 overruns:0 frame:0 TX packets:1025 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:574701 (574.7 KB) TX bytes:169249 (169.2 KB) Interrupt:10 eth1 Link encap:Ethernet HWaddr 00:0c:f1:58:79:b5 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:10 Base address:0x8000 Memory:d0202000-d0202fff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) the output of iwconfig is eth1 unassociated ESSID:off/any Nickname:"ipw2100" Mode:Managed Channel=0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:off Retry short limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I have another question. When my OS is 9.04, there is a icon about network connection on the panel at the top. After I upgraded to 9.10, that icon disappeared. How can I get that back? Best Regareds,

  Read the article

• GA 8KNXP Rev1.0: 4GB installed, only 3.5 recognized by BIOS

  - by hurikhan77

  I've installed 2x 1 GB and 4x 512 MB memory into my GA-8KNXP system which would sum up to 4GB. The specs from the manual say: Maximum memory support: 4GB. If all six slots are utilized, slot 5+6 may only equipped with single-sided RAM modules. And so I did. Anyway: The BIOS counts up to 3.5 GB and finishes there. Also my linux system reports only 3.5 GB of memory although 4 GB memory support is activated in the kernel. So I suppose this is a memory mapping issue or a hardware issue. I've tried removing only on of the 512 MB memory modules leaving 5 modules in place. But that just stopped the system from powering on correctly (screen stays black although fans and leds come to live). Dual Channel was detected and enabled so the system technically found all 6 modules. "dmidecode" in linux reports only memory in slots 1 to 4 and ignores slots 5+6, so it only detects 3 GB of memory. It also says the system would support up to 16 GB of memory with 4 GB modules per slot. I think technically the chipset should be able to offer and utilize the complete 4 GB memory range. Any clues what else I could check? Or do I have just to live with 0.5 GB wasted memory?

  Read the article

• Ubuntu 9.10 RSA authentication: ssh fails, filezilla runs fine

  - by MariusPontmercy

  This is quite a mistery for me. I usually use passwordless RSA authentication to login into my remote *nix servers with ssh and sftp. Never had any problem until now. I cannot connect to an Ubuntu 9.10 machine: user@myclient$ ssh -i .ssh/Ganymede_key [email protected] [...] debug1: Host 'ganymede.server.com' is known and matches the RSA host key. debug1: Found key in /home/user/.ssh/known_hosts:14 debug2: bits set: 494/1024 debug1: ssh_rsa_verify: signature correct debug2: kex_derive_keys debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: .ssh/Ganymede_key (0xb96a0ef8) debug2: key: .ssh/Ganymede_key ((nil)) debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: publickey debug1: Offering public key: .ssh/Ganymede_key debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Trying private key: .ssh/Ganymede_key debug1: read PEM private key done: type RSA debug2: we sent a publickey packet, wait for reply debug1: Authentications that can continue: publickey,password,keyboard-interactive debug2: we did not send a packet, disable method debug1: Next authentication method: keyboard-interactive debug2: userauth_kbdint debug2: we sent a keyboard-interactive packet, wait for reply debug2: input_userauth_info_req debug2: input_userauth_info_req: num_prompts 1 Then it falls back to password authentication. If I disable password authentication on the remote machine my connection attempt just fails with a "Permission denied (publickey)." state. Same thing for sftp from command line. The "funny" thing is that the exact same RSA key works like a charm with a Filezilla sftp session instead: 12:08:00 Trace: Offered public key from "/home/user/.filezilla/keys/Ganymede_key" 12:08:00 Trace: Offer of public key accepted, trying to authenticate using it. 12:08:01 Trace: Access granted 12:08:01 Trace: Opened channel for session 12:08:01 Trace: Started a shell/command 12:08:01 Status: Connected to ganymede.server.com 12:08:02 Trace: CSftpControlSocket::ConnectParseResponse() 12:08:02 Trace: CSftpControlSocket::ResetOperation(0) 12:08:02 Trace: CControlSocket::ResetOperation(0) 12:08:02 Status: Retrieving directory listing... 12:08:02 Trace: CSftpControlSocket::SendNextCommand() 12:08:02 Trace: CSftpControlSocket::ChangeDirSend() 12:08:02 Command: pwd 12:08:02 Response: Current directory is: "/root" 12:08:02 Trace: CSftpControlSocket::ResetOperation(0) 12:08:02 Trace: CControlSocket::ResetOperation(0) 12:08:02 Trace: CSftpControlSocket::ParseSubcommandResult(0) 12:08:02 Trace: CSftpControlSocket::ListSubcommandResult() 12:08:02 Trace: CSftpControlSocket::ResetOperation(0) 12:08:02 Trace: CControlSocket::ResetOperation(0) 12:08:02 Status: Directory listing successful Any thoughts? M

  Read the article

• Am I getting the right memory for my motherboard?

  - by Daniel Carvalho

  Hi technophiles; I have a Gigabyte GA-EP45-DS motherboard. Also, the memory that came with my computer was two Transcend aXe RAM 1066MHZ 1GB modules. The thing is, I noticed that my motherboard has "DDR2 1200" written on it. This concerns me, have I bought slower memory than my computer is supposed to have ideally? Now, I'm not super concerned at a granular level about the best optimal RAM with the best CAS latency etc... but I do hope at least that I've got the right speed. Now, as far as I know, there is no such thing as ram at 1200MHZ? Am I right? You see, because I'm thinking of getting more RAM now, before I can't find the same type or speed any-more and just want to make sure it's the right thing. Furthermore, if the memory is slower than what I should be getting for my motherboard, what RAM should I be getting, and will that new RAM play nice with my old RAM? If I get new RAM at a different speed, would it be better / more beneficial performance-wise to omit the old RAM because of how the whole DUAL channel RAM thing works? I'm not too clued up on this area. Thanks chiefs.

  Read the article

• Unable to access site over HTTPS using self signed certificate

  - by James

  I am developing a REST API which I want to secure with SSL/TLS. I have implemented a large part of the API which I have tested over HTTP, however, I am now at the stage where I want to switch it over to use HTTPS. At the moment the API is hosted on a Windows XP professional SP2 box running IIS 5.1 (development environment only) and I used the SelfSSL.exe tool from the IIS 6.0 Resource Kit Tools to generate a server certificate. I then configured my API to use this certificate which all appeared to work fine as I attempted to connect to my API using HTTP and I get a 403 response saying "... must be accessed over a secure channel...". However, the problem is when I attempt to access the same the API over HTTPS it just appears to hang! As this is a development environment at the moment I don't have a domain name (just a static IP address) and the API is running on port 81. Also (incase it matters) the API is the default site (I replaced it). Any ideas why I can't connect using HTTPS?

  Read the article

• Connecting a laptop to a TV via HDMI

  - by Madmartigan

  I just bought a new Dell XPS17 laptop (Win7) that only has HDMI output. My last 2 laptops had VGA, which I used to connect to my Sony Bravia 32" TV with no issues, but with the HDMI it's been quite a headache. Drivers for display adapters have been updated to the latest versions: Intel(R) HD Graphics Family NVIDIA GeForce GT 550M I went to a store and plugged in to 4 different TVs from different manufacturers. A sales rep and I spent about 30 minutes being baffled by the results (which are the same as my current TV): Extreme buggy behavior in the Nvidia and Windows display/resolution control panel Can not extend or duplicate displays, can only select one Third and fourth output devices "randomly" detected by the Windows control panel Could not get the screen to fit the output (edges cut off on all sides by about a half inch) Resolution and colors less than perfect. Artifacts around text. Display "randomly" cuts out Defaults to TV output only when plugged in Can not change resolution on either device when connected No audio from the TV Plugged in to 3 monitors from different manufacturers: Defaults to duplicated displays when plugged in Everything works perfectly So far, four people have gone through all the settings in the latop with no luck. I had similar, but not exactly matching results with a different laptop. I'm using the Sony Bravia currently at home, but in order to get it to work I have to turn on the laptop, wait until the display shows up on it, close the lid, then cycle through each output channel on the TV until I come back around to the HDMI port again, but still I have the symptoms described above. However: Once in a while, it just works. Sometimes, seemingly randomly, the output fits the screen perfectly. Sometimes the audio comes through the speakers too, but not always. Usually my screen saver "Mystify" will come up with a message that it cannot be displayed due to a limitation of the video card, but then sometimes it works fine. These 3 things seem to be independent of each other and don't always happen together. So, is there any way to get the laptop to output correctly to a TV, or is it just not meant to be?

  Read the article

• Downmix surround to Dolby Pro-Logic at the OS/driver level in Windows 7?

  - by davr

  First off, I'm talking about Dolby Pro-Logic, a really old tech for encoding 4 audio channels (L/R/C/SR) into two analog outputs, and then extracting them again. It was used in surround sound systems in the last century. I have a modern PC that can output 5.1 analog audio (Three outputs on the back carry six channels of audio). But I have a really old surround sound reciever that only has a two-channel, L/R input, which it extracts 4 channels of audio from, and outputs to 5.1 speakers. What I want is some way for the OS, Windows 7, to act as if I really had 5.1 audio channels available, so applications produce surround audio, but before outputting it out of the back of my PC, apply Dolby Pro-Logic matrix encoding so that it outputs over only two channels. These two channels would then get sent to my receiver via a RCA cable, which would decode it again and drive the surround speakers. Is anything like this possible? I'm pretty sure I could do it at an application / codec level, but I'm looking for something that I just have to set once.

  Read the article

• What Media Extender / Centre Set up should I use?

  - by Bryn Hird

  I have installed cat6 throughout the house which I use for telephony and network. In my cellar I have a NAS Server, gigabit switch and I want to install a Media Centre to stream my video's, music, photo's and live TV (coax from the aerial to the cellar) over the cat6. Yeah I know I can get stuff on the internet but shared experience of watching TV as a family as it happens is a big plus for live TV. I'm aiming for 1080p. I want different users to be able to watch different channels. Max users = 4. I've played a little with Windows Media Centre, works fine with live TV. Likewise I have XBMC up and running with live TV. The issue I have is what do I put near the TV. I'd like a consistent user interface (grandma and the the other technophobes in the house are continually pestering me on how to use different TVs, change channel, inputs etc.) so a key part of this for me is to make the user experience the same and simple i.e. no keyboards / PCs hanging around the TV. I've just bought a Linksys DMA 2200 to test the Windows Media Centre, but obviously off eBay as they're a dying breed. And with Windows Media Centre removed from Microsoft plans such devices will get rarer. And as for 1080p, think I can forget it with that set up. I have tested XBOX 360, also works but ditto on Microsoft plans for WMC. I was thinking of a WD Live TV to test the XMBC setup. Now to the question. Any advice on Media Centre / Extender setups that will do the job as above and have some degree of futureproofing (building my own with my Raspberry PI is a last resort). I'd like to understand the standards involved in the futureproofing if anyone knows (DNLA, RVU etc.).

  Read the article

• Can I connect a Playstation 3's HDMI output to my monitor's DVI-D input? [migrated]

  - by HankJDoomstorm

  I'm attempting to connect my Playstation 3 to my computer monitor. The monitor has a DVI-D (dual link) input, so before distinguishing between the different DVI varieties, I bought a DVI-I (dual link) to HDMI converter that won't fit into the port on the monitor (not only that, there isn't enough physical space in the back of the monitor to fit that much stuff before it hits the bottom of it). So I grabbed a DVI-D (single link) cable and got a female-to-female DVI-I coupler, and plugged the DVI-D cable into the monitor and the whole mess of converters. The end result was HDMI to DVI-D single link, but my monitor isn't receiving a signal on its digital channel. (For clarity's sake: DVI-D DL input on Monitor, DVI-D SL cable, DVI-I DL female-to-female coupler, DVI-I DL to HDMI converter, HDMI output on PS3) I don't know much about this stuff (obviously), but my educated guess is that the bandwidth of the PS3 is too high for the DVI-D Single Link cable, so nothing's getting through. Will replacing the single link cable with dual link resolve this? If not, is it possible at all? Oh, I should mention I'm aware I won't get audio through the monitor. I have an RCA to 3.5mm converter for that.

  Read the article

• Under FreeBSD, can a VLAN interface have a smaller MTU than the primary interface?

  - by larsks

  I have a system with two physical interfaces, combined into a LACP aggregation group. That LACP channel has two VLANs, one untagged (the "native vlan") and one using VLAN tagging. This gives us: lagg0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> ether 00:25:90:1d:fe:8e inet 10.243.24.23 netmask 0xffffff00 broadcast 10.243.24.255 media: Ethernet autoselect status: active laggproto lacp laggport: em1 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> laggport: em0 flags=1c<ACTIVE,COLLECTING,DISTRIBUTING> vlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=3<RXCSUM,TXCSUM> ether 00:25:90:1d:fe:8e inet 10.243.16.23 netmask 0xffffff80 broadcast 10.243.16.127 media: Ethernet autoselect status: active vlan: 610 parent interface: lagg0 Is it possible to set a 9K MTU on lagg0 while preserving the 1500 byte MTU on vlan0? Normally I would simply try this out, but this is actually on a vendor-supported platform and I am loathe to make changes "behind the back" of their administration interface. This system is roughly FreeBSD 7.3.

  Read the article

• Excel data representation: show me all people who did not pass the exam

  - by dreftymac

  Background I have an excel spreadsheet with the results of a pass/no-pass exam. Students are allowed to take the exam as often as they want until they either pass, or give up trying. student ;; result ;; date [email protected] ;; no-pass ;; 2000-06-07 [email protected] ;; pass ;; 2000-06-07 [email protected] ;; pass ;; 2000-06-07 [email protected] ;; no-pass ;; 2000-06-07 [email protected] ;; pass ;; 2000-06-07 [email protected] ;; pass ;; 2000-06-08 [email protected] ;; no-pass ;; 2000-06-08 Question Using a pivot-table or something else, how can I get excel to show me a clean report or representation of this data on another sheet that answers the question: Who are all the people who took the exam, but never got a passing grade? In the above example it would just show me [email protected] ;; no-pass ;; with all the dates that delta took the exam. I know excel is not a database nor a reporting tool per-se, but it would be great if I could get it to do this.

  Read the article

• This .mpg video clip doesn't play well

  - by Roey

  I've installed K-lite mega codec pack v6.9.0 with playback essentials without player. My default and only media player is windows media player. here are the clip's media info: General Complete name : D:\Users\Roey\Downloads\B384MV.mpg Format : MPEG-PS File size : 273 MiB Duration : 4mn 59s Overall bit rate : 7 643 Kbps Video ID : 224 (0xE0) Format : MPEG Video Format version : Version 2 Format profile : Main@High Format settings, BVOP : No Format settings, Matrix : Default Format settings, GOP : M=1, N=15 Duration : 4mn 57s Bit rate mode : Variable Bit rate : 7 363 Kbps Nominal bit rate : 9 000 Kbps Width : 1 920 pixels Height : 1 080 pixels Display aspect ratio : 16:9 Frame rate : 25.000 fps Color space : YUV Chroma subsampling : 4:2:0 Bit depth : 8 bits Scan type : Progressive Compression mode : Lossy Bits/(Pixel*Frame) : 0.142 Stream size : 261 MiB (96%) Audio ID : 192 (0xC0) Format : MPEG Audio Format version : Version 1 Format profile : Layer 3 Mode : Joint stereo Duration : 4mn 59s Bit rate mode : Constant Bit rate : 128 Kbps Channel(s) : 2 channels Sampling rate : 44.1 KHz Compression mode : Lossy Stream size : 4.56 MiB (2%) Menu When I play it there is no sound (just a little "kahhhh" noise every 10-20 seconds) and the frames are moving very slow - it "jumps" frames. A blue tray icon [FFa] "ffdshow audio decoder" pops with the following details: Input:MP3, stereo, 44100 Hz (libavocodec) Output:PCM, stereo, 44100 Hz, 16-bit integer Any help will be much appreciated. Thanks

  Read the article

• Xen Bridge only working when IP Assigned

  - by m.sr

  Hey! Just had an (in my sense) obscure situation. I have a Xen Server with bridged networking. Everything works fine since month. A while ago i configuresd a second bridge. only some DomUs get an channel on this bridge - my Dom0 doesn't need to / should'nt use this bridge. So just 5 minutes ago while rebooting the xen host (because of an other problem with the UPS) i decided to removed the fixed ip from the the interface of the Dom0 which belongs to the second bridge. So after reboot i noticed that none of the interfaces on the second bridge is available. I couldn't find a problem. Everything was just like before the reboot, except the interface of the Dom0 had no IP address. After a while i tried to give the DomO interface of this bridge an IP again and ... BOOM ... everything is up and running again! WTF? Why is it important to have the interface of a bridge configured in the Dom0? Even when confiugured 'wrong' (complitely different netowkr settings as the network really hanging on the bridge) everythjing works fine ... I don't get it. Could please someone explain? Tnaks a lot!

  Read the article

• Intel Ethernet Bottlenecking Internet?

  - by Donald Darma

  I'm having trouble with my internet speeds. So I just recent build a pc and everything is fine. I installed the Intel drivers and connected to the internet. It connects but I'm only half the speed I should be getting. My normal speed is 20mbps but speedtest.net is only showing 10. It can't be my ISP (which is TWC if anyone is asking) because my other devices like my laptop and my smartphone are showing 20 down. Heres my system: CPU: i5 4430 HSF: Stock cooler Mobo: Gigabyte Z87MX-D3H GPU: x2 MSI R7950-3GD5/OC BE RAM: Crucial Ballistix Tactical Tracer 8GB dual channel PSU: Silencer High Performance Power Supply 750 Watt 80+ (It's a subdivision of OCZ) HDD: Seagate Barracuda 7200RPM 3TB SSD: Samsung 840 Evo 120 GB Case: Corsair Obsidian 350D Edit: I am using the stock adapter that is on the motherboard. I know for a fact that the cable is good because I used it on my laptop and it ran fine. Its a CAT5E cable. I also ran IPERF and its giving me the same results, 10 mbps.

  Read the article

< Previous Page | 120 121 122 123 124 125 126 127 128 129 130 131  | Next Page >